Applied Machine:
(unit:mm)
(unit:mm)
177
420
393
1591
1591
1231
1021
899
950
293
2142
1021
254
100
760
400
85
175
947
100
2821
FS-503+RU-504+C6500+DF-609+PF-601
(unit:mm)
177
393
1591
1177
1021
100
254
760
544
85
175
947
100
2965
FS-503+LS-501+RU-504+C6500+DF-609+PF-601
(unit:mm)
177
393
1591
1177
1021
100
254
544
760
785
85
175
947
100
3750
SD-501+FD-501+RU-503+C6500+DF-609+PF-601
(unit:mm)
177
393
1591
1231
1021
1170
760
400
175
3652
100
947
100
E-1
A03U956200
Corrugated fiberboard
Veneer
Cushion(rear)
Note:
Lifting the machine in an awkward position or
transporting it in a poorly balanced position could
result in personal injury. When transporting the
machine, assign an adequate number of persons
to the job and ensure that each person can take
a good position of not being excessively loaded.
(mass: approx. 340 kg)
1. Lift the Machine by hand to remove the cushion.
Caution:
Perform the process mentioned above one side at
a time.
Front
A03UIXE067SA
Cushion
Cushion
A03UIXE064SA
2. Fix the veneer with the nail at the top end face of
the pallet, setting its beveled portion upward.
Corrugated fiberboard
Nail:2pcs.
Veneer
<Front>
A03UIXE065SA
E-2
Name
No.
Shape
Qty
Name
12. Nails
1. Rear cover/2
Shape
Qty
2
13. Veneer
1
1
14. Clamp
A03UIXC005SA
2. Developer
(Y/M/C/K)
1
each
1
A03UIXC006SA
3. Developing unit
(Y/M/C/K)
each
1
A03UIXC007SA
4. Transfer unit
15. TP screw
M4x6
16. TP screw
M3x6
19. Installation
manual
1
A03UIXC008SA
6. Separation
claw unit
1
A03UIXC010SA
7. Working table
1
A03UIXC011SA
8. Control panel
1
A03UIXC012SA
9. Users guide
holder
1
A03UIXC013SA
English
French
Italian
German
Spanish
Japanese
Chinese(
)
Chinese(
)
Korean
A03UIXC014SA
1
15KVIXC014SA
E-3
each
1
V. Installation Procedure
Note 1:
Be sure to correctly follow the procedures in order
as explained in this Installation Manual. If you do
not follow the procedure in order, the image trouble may occur.
Black PET
Note 2:
Release all locks, and do not plug the power cord
into the outlet until you are instructed to do so.
1. Inspect the outward of the Machine.
2. Remove the wrapping sheet on the top.
3. Remove the locking tapes put on the exterior
panels.
Note:
Locking guide tapes indicate the portions to be
unlocked; those tapes should be removed after
the completion of each unlocking procedure.
Locking tape
Locking
guide tape
Locking tapes
A03UIXE002SA
Locking
tapes
Locking screw
Locking tapes
Wrapping sheet
A03UIXE003SA
Locking
tapes
Power cord
A03UIXE001SA
A03UIXE004SA
E-4
(2) Loosen the upper lock screw of the toner supply unit.
A03UIXE017SA
A03UIXE007SA
Toner supply
unit lock screw
(under)
A03UIXE005SA
A03UIXE061SA
A03UIXE006SA
A03UIXE062SA
00AAIXE000SA
E-5
Locking tape
ADU Lock bracket(top)
A03UIXE010SA
Toner supply
unit stopper
Protection paper
A03UIXE008SA
Locking tape
Desiccating agent
ADU lock
A03UIXE011SA
A03UIXE009SA
Note:
Do not remove the red tags in this step because it
shows that locking materials are on ADU inner part
side.
Locking tape
Locking materials
A03UIXE069SA
Locking tape
A03UIXE068SA
E-6
Cap
Top cover/Rr
Locking tape
Spacer
A03UIXE014SA
A03UIXE063SA
00AAIXE000SA
Top cover/Rr
Right cover/Rr
Loosen
the screws
A03UIXE015SA
A03UIXE012SA
Connector cover
A03UIXE013SA
E-7
TP screws M46
TP screws M46
TP screws M46
Control panel
installation section
A03UIXE070SA
Clamp
Large connector
A03UIXE019SA
Clamp
Clamp
Small connector
A03UIXE020SA
Large connector
A03UIXE018SA
E-8
Tape
A03UIXE025SA
A03UIXE022SA
Developing unit
Lever
A03UIXE021SA
Straight
C
K
A03UIXE026SA
A03UIXE024SA
E-9
A03UIXE029SA
Drum blade
pressure release
screw
Rear
Connector
Drum blade
pressure release
screw
Connector location
of connections
A03UIXE028SA
E-10
A03UIXE030SA
Transfer unit
fixing materials
A03UIXE031SA
A03UIXE032SA
A03UIXC001SA
Mylar
A03UIXE041SA
E-11
Rear
Transfer unit
1st transfer
roller locking
materials
A03UIXE036SA
A03UIXE033SA
Rear
Red papers
Front
Lock screws
TP screw
M3x6
Rear
Slit
A03UIXE034SA
A03UIXE037SA
Transfer unit
protection cover
A03UIXE035SA
E-12
Belt driving
coupling
Application area
A03UIXE040SA
A03UIXE038SA
Grooves
A03UIXC003SA
(14) Remove the transfer unit stand, pull the handle on the top of the transfer unit, and lift the
belt.
Note:
Return the transfer unit stand to the original position.
Handle
TP screws M3x6
A03UIXE039SA
Pins
A03UIXE042SA
E-13
(15) Set the transfer unit with the surface of its belt
facing the drum side. Position the unit obliquely,
as shown in the figure, and move it into place
from the rear, then align it so that the pins of the
transfer unit are engaged by the positioning
hooks (4 places) in the front and rear.
Note:
Be careful not to hit the drum with the transfer unit.
(17) Turn the transfer unit fixing material in the direction of the arrow until it reaches the screws, and
secure it with screws (2 screws each).
Transfer unit
fixing materials
Rear side
A03UIXE045SA
Positioning hooks
Front side
Positioning hooks
A03UIXE043SA
A03UIXE046SA
Handle
Screws
Rear cover / 2
A03UIXE044SA
A03UIXE047SA
E-14
Top cover/Fr
Y developer
charging plate
fixing screws
M C K
developer
charging plate
fixing screws
A03UIXE023SA
Developer
charging plate
A03UIXE048SA
(3) Place a piece of paper below the toner insertion slots to prevent soiling.
Developer Charging
funnel/L
Developer charging plate
Paper for prevention of dirt
A03UIXE049SA
A03UIXE051SA
E-15
Step
8. After the developer is completely poured in,
touch the CANCEL.
9. Touch the M (magenta).
10. Pour in the developer in the same manner as
for yellow.
Note:
Ensure before loading that the color of the
developer matches to the color displayed
on the screen.
Make sure the developer charging funnel /
L is cleaned before moving from one color
of the developer to the next.
Replace the developer charging funnel /U
for each color of developer.
Follow the same procedure for cyan (C)
and black (K) developers.
Note:
When removing the developer charging plate from
the machine, lift the right side of the stopper plate,
and slide the developer charging plate to the left
side to remove it.
A03UIXE052SA
A03UIXC004SA
E-16
Stopper plate
A03UIXE053SA
Note:
Execute the adjustments and settings below.
Step
1. Turn ON the Main power switch.
E-17
A03UIXC015SA
Internal door
A03UIXE055SA
Step
E-18
OC-506
Working table
installation part covers
A03UIXE056SA
OT-502
Paper exit tray unit
(option)
A03UIXE059SA
Working table
A03UIXE060SA
A03UIXE058SA
E-19
Note:
User networks and the PC environment are usually managed by technical administrators. When
doing the following setup, be sure to check with
the person in charge to get approval and proceed
under that persons supervision.
E-20
Step
1. Press the [Utility/Counter] key.
2. Touch Machine Admin. Setting.
Note:
If an administrator password has been set
already, enter the current password and
touch OK.
3. Touch Network Setting.
4. On the screen that appears when Machine
NIC Setting is touched, set the following
items.
IP Address: IP address of the machine
Subnet Mask:
subnet mask of network to be connected to
Gateway Address:
IP address of the default gateway
5. Touch OK to display the Network Setting
screen.
6. When the setup is completed, be sure to
turn OFF then turn ON the Main and Sub
power switches. (Otherwise the new settings
will not be registered. When turning the Main
and Sub power switches back ON, wait for
10 seconds or more after turning them OFF.)