Living
Outside
Play
Technology
Workshop
Table of Contents
Assemble a HHO Mini Torch from plumbing parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
Author:petercd
general bloke type of tinkering
Image Notes
1. not hot enough to burn fingers
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
Image Notes
1. this second pic was taken 5min later and still not hot enough to burn fingers.
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
Image Notes
1. mig welder tip
2. copper stopend
3. brass nut to retain mig tip
4. copper elbow
5. 1" connecting pipe
6. 4" connecting pipe
7. ball valve compression fittings both ends
8. 1.25" connecting pipe
9. coupler
10. LP gas hosetail
11. standard 10mm barb
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
Image Notes
1. stabdard 0.8mm tip before mods
2. 0.9mm tip after mods, roughly 0.45mm in dia
Image Notes
1. M6 nuts to protect the thread while hitting on top with a hammer
Image Notes
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
Image Notes
1. a view down the threaded tip hole showing the brass and solder layer
Image Notes
1. another option is brass contacts from an old carbon dry cell
2. my drilled and tapped brass earth pin from a 15A 3pin plug
Image Notes
1. the view inside before soldering
2. dont leave this tip in while soldering this was just a test fit
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
Image Notes
1. ss allen bolt used during soldering to line up the parts
Image Notes
1. modified ss M6 washer
Related Instructables
Hydroxy Gas
Generator by
petercd
Mini Hydrogen
gas generator
(video) by
kevins82
How to
assemble a
HHO Generator
and why it
works by
Electrified
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/
How to Convert
Water into Fuel
by Building a
DIY
Oxyhydrogen
Generator by
The King of
Random
Advertisements
http://www.instructables.com/id/Assemble-a-HHO-Mini-Torch-from-plumbing-parts/