0.5
Gears
Spur
Screw
D
S
L
S1 Shape
■ Module 0.5
Catalog Module No. of teeth Bore NOTE 1 Hub dia. Pitch dia. Outside dia. Face width Hub width Total length Cap Screw Dimensions NOTE 2
Ǿ
Bore (mm)
Ǿ
Ǿ
Ǿ
Ǿ
104
Acetal Fairloc Hub Spur Gears
Gears
Spur
Specifications
Precision grade JIS N10 grade (JIS B1702-2: 1998) Tooth hardness 110~120HRR
D
Gear teeth Standard full depth Surface treatment - S
L
Pressure angle 20° Tooth surface finish Cut
105
DSL Acetal Fairloc Hub Spur Gears Modules
0.8~1
Gears
Spur
D
S
L
S1 Shape
■ Module 0.8
Catalog Module No. of teeth Bore NOTE 1 Hub dia. Pitch dia. Outside dia. Face width Hub width Total length Cap Screw Dimensions NOTE 2
■ Module 1
DSL1 - 15 1 015 5 14 1500 017.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 16 1 016 5 14 1600 018.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 18 1 018 5 14 1800 020.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 20 1 020 5 14 2000 022.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 24 1 024 5 14 2400 026.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 25 1 025 5 14 2500 027.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 28 1 028 5 14 2800 030.0 5 8.5 13.5 M2.5 3.3 4.4
DSL1 - 30 1 030 8 17 3000 032.0 5 9.8 14.8 M3.5 4.3 5.9
DSL1 - 32 1 032 8 17 3200 034.0 5 9.8 14.8 M3.5 4.3 5.9
DSL1 - 35 1 035 8 17 3500 037.0 5 9.8 14.8 M3.5 4.3 5.9
DSL1 - 36 1 036 8 17 3600 038.0 5 9.8 14.8 M3.5 4.3 5.9
DSL1 - 40 1 040 8 17 4000 042.0 5 9.8 14.8 M3.5 4.3 5.9
DSL1 - 45 1 045 8 17 4500 047.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 48 1 048 8 17 4800 050.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 50 1 050 8 17 5000 052.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 56 1 056 8 17 5600 058.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 60 1 060 8 17 6000 062.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 64 1 064 8 17 6400 066.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 70 1 070 8 17 7000 072.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 72 1 072 8 17 7200 074.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 80 1 080 8 17 8000 082.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 - 90 1 090 8 17 9000 092.0 5 9.8 14.8 M3.0 4.3 5.9
DSL1 -100 1 100 8 17 100000 102.0 5 9.8 14.8 M3.0 4.3 5.9
CAUTION: Gears with wider face widths such as SS and SSA series can be used as the mating gars to these.
NOTE 1: The bore cannot be modified. It is possible to pin the gear to the shaft to prevent slippage.
NOTE 2 : Do not tighten the clamping screw without inserting a shaft, or the bore will be permanently deformed and will not accept a shaft.
106
Acetal Fairloc Hub Spur Gears
Gears
Spur
Specifications
Precision grade JIS N10 grade (JIS B1702-2: 1998) Tooth hardness 110~120HRR
D
Gear teeth Standard full depth Surface treatment - S
L
Pressure angle 20° Tooth surface finish Cut
107