:clap::clap:
GUSTO KO LANG MAKATULONG!!!!!!!!!! BECAUSE I experience the same kind of problem recently
QPST PROBLEM CM FLARE SOLUTION
follow lang po ninyo ung steps na yan ayan din po ung ginawa ko sa flare ko ung na deadboot po xia pde din
po yan sa hard brick as long as na dedetect pa xia nang computer
Follow this guide carefully and you can revive your dead Karbonn A9+/ CM Flare after Jelly Bean Upgrade.
Tools Needed:
Dead Phone (When u connect to PC it should install Qualcomm HS-USB QD Loader 9008 Driver) You can see
links before reply
QPST.2.7.399 You can see links before reply
Flare Revival kit Link You can see links before reply
PC with 32 bit Windows (XP/Vista/7/8) (64bit casus problem in QPST installation)
Connect ur phone to PC and let the driver install
Install QPST
You can see links before reply
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your
device ->exit.
You
You
You
You
can
can
can
can
see
see
see
see
links
links
links
links
before
before
before
before
reply
reply
reply
reply
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot
loaders -> Browse for the device com port
You can see links before reply
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and
thats important) and it will search for the new hardware found, install the driver
You can see links before reply
ALTERNATIVE PROCEDURE
Solution For Deadboot
Download first this Files bago tayu mag simula
QPST 2.7 build 399 You can see links before reply
JB drivers You can see links before reply
Jelly Bean BP Firmware
You can see links before reply
WARNING : Supported ito sa mga flare na nadedetect pa ng Pc if hndi ito ma detect sa pc dont do this
anymore
Install QPTS (alam ko pamilyar kayo jn.. ginagamit yan sa mga broadband stick..)
install lahat ng drivers para walang aberya
Install drivers
1. Connect deadboot flare to PC / Laptop.
2. Go to device manager, expand PORTS (COM & LPT). Check if there is an item called Qualcomm HSUSB
QDLOADER 9008. If the item is there, you are done with driver install. If it does not exist, proceed to step3.
3. If there is no item under PORTS (COM & LPT), check device manager under OTHER DEVICES > Unknown
Device
4. Double click UNKNOWN DEVICE > UPDATE DRIVER > BROWSE MY COMPUTER > browse to the folder
where you saved extracted the ICS / JB drivers. It will install the driver, if it prompts for unsigned drivers,
press INSTALL ANYWAY.
5. It should now be listed under COM PORTS > Qualcomm HSUSB QDLOADER 9008.
Run QPST and reprogram EMMC (dito tayu mag sisimula)
1. Run EMMC SOFTWARE DOWNLOAD.
2. Press BROWSE, it will detect your phone. Look for the PHONE TAB that says DOWNLOAD. Press OK.
3. Put check mark on PROGRAM BOOTLOADERS, PROGRAM MMC DEVICE, TRUSTED.
4. Under FLASH PROGRAMMER FILENAME, enter MPRG8X25.hex
5. Under BOOT IMAGE, enter 8X25_msimage.mbn
6. Press LOAD XML DEF > navigate to your extracted JB firmware > select rawprogram0 > press OPEN.
7. Press LOAD PATCH DEF > navigate to your extracted JB firmware > select patch0 > press OPEN
8. PRESS DOWNLOAD
9. An warning message may appear, TIME OUT WAITING etc etc or COOKIE NOT RECEIVED. If the error is
TIME OUT WAITING, press OK and then press SWITCH DEVICE TO DLOAD. Check the flare, it will show
RESET FOR ENTRY QPST.
10. Exit EMMC SOFTWARE DOWNLOAD. Proceed to flash Jelly Bean BP Firmware and then flash Jelly Bean
img dump.
11. IF ERROR IS COOKIE NOT RECEIVED, sorry it is still bricked
PROCEDURE 3
GO TO THIS LINK!!!