0, class II
USER MANUAL
Disclaimer
We spared no efforts to make sure that the information in this
manual is correct and complete. However no liability is accepted for any
errors or omissions. Gembird Electronics reserves the right to change the
specifications of the hardware and software described in this manual
without prior notice.
No part of this manual may be reproduced, transmitted or translated
in any language in any form, by any means, without the prior written
permission of Gembird Electronics Ltd.
Gembird Electronics makes no warranties for damages resulting
from corrupted or lost data due to a mistaken operation or malfunction of
the product, the software, personal computers or peripheral devices.
Gembird is a registered trademark of Gembird Europe bv.
Other names or products not mentioned above may be registered
trademarks or trademarks of their respective owners.
Copyright 2008 Gembird Electronics Ltd. All rights reserved
http://www.gembird.eu
Features
Ergonomic design
http://www.gembird.eu
http://www.gembird.eu
Pothook can be installed for wearing the headset on right or left ear.
You can change the ear by reinstalling the pothook very easily (see the
figure 2).
http://www.gembird.eu
CHARGE SOCKET
POTHOOK POLE
http://www.gembird.eu
http://www.gembird.eu
Pairing process
1. With the headset turned off, press and hold the TALK button for five
seconds. The blue and Red LEDs will flash alternately. Release the TALK
button. The headset is now in pairing Mode.
2. Turn on the mobile phone, initiate the device Bluetooth discovery
feature. Refer to the mobile phone user guide for instructions for initiating
this feature.
3. When prompted by the mobile phone, enter the headset default pin
code 0000.
4. When pairing is complete, the blue LED on the headset will flash in
three second intervals and the headset will be placed in standby mode,
ready to make and receive calls.
5. The disconnection or lost links can occurs due to the following
reasons:
The range between headset and mobile phone is over 10 feet.
Mobile phone has disconnected the link in order to save the
power or other purpose.
Either device has been switched off.
Note: The headset will keep the connection with mobile phone at all
times if both connection links have been built up.
Canceling the pairing mode.
http://www.gembird.eu
While you are in pairing mode, you can cancel the pairing process and
turn off the headset.
Press and hold the TALK button for three seconds. Both LEDs will turn
off.
Using the BTHS-004
1. Press and hold the Talk button for four seconds. You will see blue
light flashing. The headset turns on and stay in standby mode, ready to
make and receive calls with last paired mobile phone.
2. In the stand by condition, press and hold the Talk button for four
seconds. The blue light will turn off. The headset turns off.
3. Make a call from your mobile phone. The call is auto directed to
your headset.
4. When your mobile phone rings, press the Talk button on your
headset. The call is also automatically directed to your headset.
5. You can end the call by the Talk button on your headset. Or wait
until your interlocutor will end the call. In this case no need to press the
Talk buttons. The headset will go into standby mode automatically.
6. You can make calls from your mobile phone or directly from your
headset using voice dialing commands. Just say the name of the person
you wish to call. This person will called automatically. (This feature should
be supported by your mobile phone. For more detailed information please
refer to the mobile phone Users Manual).
Adjusting The Volume
GEMBIRD EUROPE B.V.
http://www.gembird.eu
Indication
Red LED are off
Red LED is On
Both LEDs are off
Blue LED flashes one time in
three seconds interval
http://www.gembird.eu
10
calls
Headset is in pairing mode
Audible Indicators
Tones heard through the headset provide an audible Indication of a
requested action :
Beep Tone
On
Off
Pairing
Indicates
Headset has been on
Headset has been off
Headset has been put into pairing
mode
Important:
Charge the BTHS-004 only with the provided AC adapter. Using
another A/C adaptor may damage the headset.
Before use BTHS-004 please make sure that the battery has been
fully charged.
Always store BTHS004 with power off and safely protected.
Avoid storage in a hot vehicle or under the direct sunlight.
Dont expose or any of its supplied parts to rain or other liquids.
Please keep the headset dry, and clean it periodically with a soft cloth.
GEMBIRD EUROPE B.V.
http://www.gembird.eu
11
http://www.gembird.eu
12