1.
Ans.
ds=dQ/T Entropy is inversely proportional to the temperature so, as temp. Increases, entropy decreases.
2.
Why different types of sound are produced in different bikes, though they run on SI Engines?
Ans.
Engine specifications are different in different manufactures like as Bore Diameter (CC), Ignition timing. Also the exhaust
passage takes more responsible for sound.
3.
Ans.
746.2 Watt
4.
Ans.
Rear wheel sprocket works under the principle of ratchet and pawl.
5.
Ans. Octane No.- Octane number is defined as the percentage, by volume, of iso octane in the mixture of iso octane and hheptane. It is the measure of rating of SI engine.
Cetane No.- Cetane number is defined as the percentage, by volume, of n-cetane in the mixture of n-cetane and alpha methyl
naphthalene. It is the measure of rating of CI engine.
6.
Ans.
Differential mechanism
7.
Ans.
8.
Ans.
Divide the shaft diameter size by 5, it will give last two digit of the bearing no. and according to type of load we have to
choose the type of bearing and that will give prior number of the bearing.
9.
Ans.
Improving the surface finish by Polishing & providing residual stress by Shot peening.
10.
What happens if gasoline is used in a Diesel Engine, Siesel Engine will work?
Ans.
No, It will not work, as the Compression ratio of Petrol engine is 6 to 10 & that of Diesel engine is 15 to 22. Thus on such
high compression, gasoline gets highly compressed & it may blast.
11.
Ans.
When a material is compressed in one direction, it usuallytends to expand in the other two directions perpendicular tothe
direction of compression. This phenomenon is called thePoisson effect. Poissons ratio is a measure of the Poisson effect.
For rubber = 0.5
For steel = 0.288
For wood < 0.2
Thus Poissons ratio is higher in RUBBER.
12.
Ans. Centrifugal pump is a kinetic device. The centrifugal pump uses the centrifugal force to push out the fluid. So the liquid
entering the pump receives kinetic energy from the rotating impeller. The centrifugal action of the impeller accelerates the liquid to a
high velocity, transferring mechanical (rotational) energy to the liquid. So it discharges the liquid in high rate. It is given in the
following formulae:
2
R-Radius
14.
Why Cavitation will occur in Centrifugal Pump and not in Displacement Pump?
Ans. The formation of cavities (or bubbles) is induced by flow separation, or non-uniform flow velocities, inside a pump casing. In
centrifugal pumps the eye of the pump impeller is smaller than the flow area of pipe. This decrease in flow area of pump results in
increase in flow rate. So pressure drop happened between pump suction and the vanes of the impeller. Here air bubbles or cavities
are formed because of liquid vapour due to increase in temperature in impeller. This air bubbles are transmitted to pump which
forms cavitation.
15.
Ans. Centrifugal pump. Because flow rate is higher compared to reciprocating pump. Flow is smooth and it requires less space to
install. Lower initial cost and lower maintenance cost.
16.
Ans. The centrifugal has varying flow depending on pressure or head, whereas the Positive Displacement pump has more or less
constant flow regardless of pressure.
Likewise viscosity is constant for positive displacement pump where centrifugal pump have up and down value because the higher
viscosity liquids fill the clearances of the pump causing a higher volumetric efficiency. When there is a viscosity change in supply
there is also greater loss in the system. This means change in pump flow affected by the pressure change.
One more example is, positive displacement pump has more or less constant efficiency, where centrifugal pump has varying
efficiency rate.
17.
Ans. In Solid mechanics, in the field of rotor dynamics, the critical speed is the theoretical angular velocity which excites the
natural frequency of a rotating object, such as a shaft, propeller or gear. As the speed of rotation approaches the objects natural
frequency, the object begins to resonate which dramatically increases system vibration. The resulting resonance occurs regardless
of orientation.Whirling Speed is due to the unbalanced forces acting on a rotating shaft.
18.
Ans. Diesel engine is a prime mover, for a generator, pump,and for vehicles etc. generator is connected to engine by shaft.
mostly in thermal power plat ,there is an engine is used to drive generator to generate power.
19.
Ans.
20.
Ans. The heat addition and rejection processes in Otto cycle are of constant volume, whereas in Brayton cycle, they are of
constant pressure.
-Otto cycle is the ideal cycle for spark ignition engines.
-Brayton cycle is the ideal cycle for gas power turbines.
21.
Ans.
22.
Ans. DTSI stands for Digital Twin Spark Plug Ignition. The vehicles with DTSI Technology use 2 spark plugs which are controlled
by digital circuit. It results in efficient combustion of air fuel mixture.
Digital - Since the spark generation will be initiated by a microchip.
Twin - Since two spark plugs will be used.
Spark ignition - Since the ignition will be done via a spark.
23.
Ans. The point at which the fracture energy passes below a pre-determined point for a standard Impact tests. DBTT is important
since, once a material is cooled below the DBTT, it has a much greater tendency to shatter on impact instead of bending or
deforming.
24.
Ans. All the mechanical engineering systems are studied with the help of thermodynamics. Hence it is very important for the
mechanical engineers.
25.
Ans.
Ans. Generally, journal bearings have higher friction force, consume higher energy and release more heat, but they have larger
contact surface, so normally used in low speed high load applications. In anti friction bearings friction is less. One object just rolls
over each other.
27.
Ans. Fan is an air pushing device. Either Axial or Centrifugal type systems are used to move the air in low pressure. It is rotated
by a motor separately.
When the fan is a housing of blades and motor, then it called as Blower. It directs the air in a single path with high pressure.
28.
Ans. Heat rate is a measure of the turbine efficiency. It is determined from the total energy input supplied to the Turbine divided
by the electrical energy output
29.
Ans.
Bubble generation and Bubble implosion which occurs in a flowing liquid as a result of a decrease and subsequent increase in
pressure.
30.
Ans.
Ans. Face of Flange, The F.O.F (Raised face and Flat face) is used to know the accurate dimension of the flange in order to
avoid the minute errors in measurement in case of vertical or horizontal pipe lines.
33.
Ans. Pressure washing of Aircraft, Trains, Boats and Road vehicles as well as Spray washing of industrial parts and Electronic
components.
34.
Ans.
35.
Ans. Normally the temperature range from 80 degree to 110 degree Celsius. So the following temperature measurement devices
are used.
Dial Type Bearing Temperature Detector
Stator Winding Temperature Detector
Resistance Bearing Temperature Detector (Bearing RTD)
Ans. The accomplishment of a given task measured against preset known standards of accuracy, completeness, cost, and speed
is called as Performance.
Efficiency is defined as the input given and the work obtained from that input like money, time, labour etc. Its the main factor of
productivity.
36.
Ans. Its a special type valve system. The valve will open when exhaust casing pressure is excessive (high). The valve warns the
operator only; it is not intended to relieve the casing pressure.
37.
Ans.
Ans. Auto dosing is an automated system of feeding the equipment with liquid products. It is the ideal way to ensure the correct
calibrated dose at the right time every time in auto.
40.
Ans.
A force which applies on the body (material) suddenly is known as sudden force.
41.
Ans.
42.
Ans. Corrective actions are taken on discrepancies noticed during inspection of products/documents/process whereas preventive
actions are taken to eliminate the possibility ofdiscrepancy in future.
43.
Ans.
44.
Ans.
The Function of Scoop tube is regulating the varying amount of oil level in the coupling during operation of infinite variable
speed.
45.
Ans.
The amount of pressure nearest the point of performing work at the output end of a pneumatic system. The system
operating pressure is used to specify the capability of valves and actuators.
46.
Ans. Engineering is application of science. Technology shows various methods of Engineering. A bridge can be made by using
beams to bear the load,by an arc or by hanging in a cable; all shows different technology but comes under civil engineering and
science applied is laws of force/load distribution.
47.
Ans.
Wet bulb temperature is measured in a wet bulb thermometer by covering the bulb with a wick and wetting it with water. It
corresponds to the dew point temperature and relative humidity.
48.
Ans.
1. Complete combustion
2. Fuel saving
3. Homogenous combustion
Disadvantages
1. As complete combustion is occurring ,more heat liberated,not advised for long journey, engine will be over heated
2. Installation is difficult
3. Reduce engine life efficiency
49.
Ans. The rated speed tells us about the maximum speed which can be achieved by a vehicle or some other machine but the
economical speed means the speed limit at which the machine works efficiently with least consumption of fuel.eg-in normal
bikes(not racing),the max.speed limit shown on speedometer is upto 120 kmph but companies always advice their customers to
drive such bikes at around 60 kmph to have maximum mileage.
50.
Ans. Powder technology is one of the ways of making bearing material. In this method metals like bronze, Al, Fe are mixed and
compressed to make an alloy.
51.
Ans.
First Law: Energy can be neither created nor destroyed. It can only change forms. In any process in an isolated system, the total
energy remains the same.
Second Law: When two isolated systems in separate but nearby regions of space, each in thermodynamic equilibrium in itself, but
not in equilibrium with each other at first, are at some time allowed to interact, breaking the isolation that separates the two systems,
and they exchange matter or energy, they will eventually reach a mutual thermodynamic equilibrium. The sum of the entropies of the
initial, isolated systems is less than or equal to the entropy of the final exchanging systems. In the process of reaching a new
thermodynamic equilibrium, entropy has increased, or at least has not decreased.
Third Law: As temperature approaches absolute zero, the entropy of a system approaches a minimum.
52.
Ans. A unilateral tolerance is tolerance in which variation is permitted only in one direction from the specified direction.e.g. 1800
+0.000/-0.060
Bilateral tolerance is tolerance in which variation is permitted in both direction from the specified direction.e.g. 1800 +0.060/-0.060
53.
Ans.
In Brazing involves significantly lower temperatures and does not entail the melting of base metals. Instead, a filler metal is melted
and forced to flow into the joint through capillary action.
55.
Ans.
20. Which theories of failure are used for (a) ductile materials, and (b) brittle materials ?
Ans: For ductile materials, theories of failure used are maximum shear stress theory, and
maximum energy of distortion theory; while for brittle materials, theory of maximum principal
stress, and maximum strain are used.
21. What does thermal diffusivity of metals signify.
Ans: Thermal diffusivity is associated with the speed of propagation of heat into solids during
changes in temperature with time.
22. For conduction of heat, the instantaneous rate of heat flow is product of three factors.
What are these ?
Ans: (i) Area of the section of the heat flow path, perpendicular to the direction of heat flow.
(ii) temperature gradient, i.e. change of temperature w.r.t. length of path.
(ii) Thermal conductivity of material.
23. How convective heat transfer is effected and on what factors it depends ?
Ans: Convective heat transfer is effected between a solid and fluid by a combination of
molecular conduction within the fluid in combination with energy transport resulting from the
motion of fluid particles. It depends on boundary layer configuration, fluid properties and
temperature difference.
24. Which is the common element between brass and bronze ?
Ans: Copper.
25. What does following alloy designation indicate FG 250 ?
Ans: Grey cast iron with tensile strength of 250 MPa.
26. How is ceramic defined ?
Ans: It is a solid formed by combination of metallic and non-metallic elements.
27. Give one example of metal classified as per structure as BCC, FCC, HCP and CCP.
Ans: BCC (body centred cubic) structureMolybdenum
FCC (face centred cubic) structureAluminium
HCP (hexagonal closed packed) structureZinc
CCP (cubic dosed packed) structure-Copper.
28. What is the name of solid solution of carbon in alpha iron and delta iron ?
Ans: Ferrite and austenite respectively.
29. Explain the difference between pearlite and cementile ?
Ans: Pearlite is eutectoid mixture of ferrite and cementile. Cementite is chemical compound of
iron and carbon.
30. Give one example each of the following proportion of materials dimensional, physical,
technological and mechanical.
Ans: Roughness, enthalpy, toughness, and hardness respectively.
31. For which parts the Wahl factor and Lewis form factor used ?
Ans: For springs and gears respectively.
32. How oxygen can be removed from steel during melting? What are fully killed steels ?
Ans: Oxygen can be removed by adding elements such as manganese, silicon or aluminium
which, because of their high affinity for oxygen, react with it to form non-metallic oxides which
rise into the slag. Steels which have had most of their dissolved oxygen removed are called
"fully killed steels".
33. Hydrogen cannot be removed easily from molten steel. What harm hydrogen has on
property of steel ?
Ans: Execessive hydrogen results in the formation of small fissures often described as hairline
cracks or flakes in the steel. Large forgings in alloy steel are particularly sensitive to this
phenomenon.
34. What is allotrope ? In what forms of cubic pattern, iron exists ?
Ans: Some elements exist in more than one crystalline form. Each form is known as
"allotrope". Iron exists in two forms of cubic pattern, namely body centered cubic (bcc) and
face-centered cubic (fee).
35. What is the difference between alpha iron, delta iron and gamma iron ?
Ans: The bcc form of iron exists between room temperature and 910C, and between 1400C
and the melting point at 1539C. The lower temperature form is known as " alpha"-iron and the
higher temperature form as "delta"-iron. The face-centered cubic form existing between
910C and 1400C is referred to as "gamma -iron".
36. Metals, in general are of low strength and do not possess required physio-chemical and
technological properties for a definite purpose. Alloys are therefore more than metals alone.
Discuss the arrangement of atoms and structures of alloys.
Ans: Alloys are produced by melting or sintering two ore more metals, or metals and a nonmetal,
together. Alloys possess typical properties inherent in the metallic state. The chemical
elements that make up an alloy are called its components. An alloy can consist of two or more
components. The phase and structures of alloys describe the constitution, transformations
and properties of metals and alloys. A combination of phases in a state of equilibrium is called
a system. A phase is a homogeneous portion of a system having the same composition and
the same state of aggregation throughout its volume, and separated from the other portions
of the system by interfaces. For instance, a homogeneous pure metal or alloy is a singlephase
system. A state in which a liquid alloy (or metal) coexists with its crystals is a two-phase
system. Structure refers to the shape, size or the mutual arrangement of the corresponding
phases in metals or alloys. The structural components of an alloy are its individual portions,
each having a single structure with its characteristic features.
37. What is the difference between isotropic material and homogeneous material ?
Ans: In homogeneous material the composition is same throughout and in isotropic material
the elastic constants are same in all directions.
38. Explain the difference between the points of inflexion and contraflexure.
Ans: At points of inflexion in a loaded beam the bending moment is zero and at points of
contraflexure in loaded beam the bending moment changes sign from increasing to
decreasing.
39. What is the difference between proof resilience and modulus of resilience ?
Ans: Proof resilience is the maximum strain energy that can be stored in a material without
permanent deformation. Modulus of resilience is the maximum strain energy stored in a
material per unit volume.
40. What is the difference between column and strut ?
Ans: Both column and strut carry compressive load. Column is always vertical but strut as
member of structure could carry axial compressive load in any direction.
41. Explain the difference between ferrite, austenite and graphite ?
Ans: Ferrite is the solid solution of carbon and other constituents in alpha-iron. It is soft,
ductile and relatively weak.
Austenite is the solid solution of carbon and other constituents in gamma-iron. It exists in
ordinary steels at elevated temperatures, but it is also found at ordinary temperatures in
some stainless steels.
Graphite has a hexagonal layer lattice. '
42. Explain the terms solid solution, eutectic, eutectoid and peritectic.
Ans: Solid Solution. When a homogeneous mixture of two (or more) atomic forms exists in
solid state, it is known as solid solution.
Eutectic. A mixture of two (or more) phases which solidify simultaneously from the liquid alloy
is called an eutectic. Alloys in which the components solidify simultaneously at a constant
temperature the lowest for the given system, are called eutectic alloys.
Eutectoid. Eutectoid alloys are the alloys for which two solid phases which are completely
soluble become completely insoluble on cooling before a certain temperature called eutectoid
temperature.
Peritectic. A peritectic transformation involves a reaction between a solid and liquid that form
a different and new solid phase. This three phase transformation occurs at a point called
peritectic point.
43. What do you understand by critical points in iron, iron-carbide diagram ?
Ans: The temperatures at which the phase changes occur are called critical points (or
temperatures).
45. Why PERT is preferred over CPM for evaluation of project ?
Ans: PERT is based on the approach of multiple time estimates for each activity.
46. What is the percentage of chromium in 18 : 4 : 1 IISS ?
Ans: 4%.
47. What is stellite ?
Ans: It is a non-ferrous cast alloy containing cobalt, chromium and tungsten.
48. Which rays are produced by cobalt-60 in industrial radiography ?
Ans: Gamma rays.
49. What are killed steels and what for these are used ?
Ans: Killed steels are deoxidised in the ladle with silicon and aluminium. On solidification no
gas evolution occurs in these steels because they are free from oxygen.
50. What is critical temperature in metals ?
Ans: It is the temperature at which the phase change occurs in metals.
51. Car tyres are usually made of ?
Ans: Styrene-butadine rubber.
52. What is the structure of pure iron and whether it is soft or hard ?
Ans: Ferrite and it is soft.
53. Which elements increase the corrosion resistance of steel ?
Ans: Chromium and nickel.
54. What causes hardness in steel ? How heat treatment alters properties of steel ?
Ans: The shape and distribution of the carbides in the iron determines the hardness of the
steel. Carbides can be dissolved in austenite is the basis of the heat treatment of steel. If
steel is heated above the A critical temperature to dissolve all the carbides, and then cooled,
suitable cooling through the cooling range will produce the desired size and distribution of
carbides in the ferrite, imparting different properties.
55. Explain the formation of microstructures of pearlite, bainite and martensite in steel.
Ans: If austenite containing about 0.80 percent carbon is slowly cooled through the critical
temperature, ferrite and cementite are rejected simultaneously, forming alternate plates or
lamellae. This microstructure is called pearlite. At temperatures just belot the A1, the
transformation from austenite.to pearlite may take an appreciable time to initiate and
complete, but the product will be lameller pearlite. As the transformation temperature is
lowered, the time to initiate transformation shortens but the product is pearlite of increasing
distance. Depending on the channel slope, the surface conditions, the sectional geometry,
and the discharge, these may be classified into five categories : steep channel, critical
channel, mild channel, horizontal channel, and adverse channel.
25. Explain 5 types of channels.
Ans: Steep channel : In this case normal depth < critical depth.
Critical channel : In this case normal depth = critical depth.
Mild channel : In this case, normal depth > critical depth.
Adverse channel : In this case, the slope of channel bed < 0
Horizontal channel : In this case, the slope of channel bed = 0.
26. Mention two major differences between shaper and planer ?
Ans: Shaper Planer
(a) The cutting tool reciprocates (a) Work reciprocates
(b) The work is stationary (b) Tool is stationary
(c) Meant for small work pieces (c) Meant for large work pieces
(d) Only lighter cut can be taken (d) Heavy cuts can be taken
(e) Tools are smaller in size (e) Tools are bigger in size
27. Differentiate between drilling and reaming ?
Ans: Drilling Reaming
(a) It is the operation of initiating hole (a) Reaming is the operation of finishing
and
sizing a drilled/bored hole
(b) It can be done at relatively high speeds (b) It should be done only at slow speeds
(c) Larger chips are produced (c) Less chips are produced
(d) Drill has only two flutes (d) Reamer has more than 4 flutes
(e) Drill has chisel edge (e) Reamer has a bevel edge
28. What is similarity between normal shock wave and hydraulic jump ?
Ans: Both are analogous and irreversible.
29. For what purpose chills are used in moulds ?
Ans: Chills are used to achieve directional solidification.
30. What is tumbler gear mechanism ?
Ans: Tumbler gear mechanism is a mechanism consisting of number of different sized gears
keyed to the driving shaft in the form of cone and is used to give the desired direction of
motion of the lathe spindle.
31. What is relative roughness of pipe ?
Ans: It is the ratio of the size of the surface imperfections to the inside diameter of the pipe.
32. What is conicity ?
Ans: The ratio of the difference in diameter of the taper to its length is termed conicity.
33. Under what condition the effect of compressibility of fluid can be neglected ?
Ans: When Mach number is less than 0.4.
34. For which type of flow the velocity distribution in a pipe is parabolic.
Ans: For uniform laminar flow.
35. What is the relationship between center line velocity and average velocity for a
laminar flow in a pipe ?
Ans: Average velocity = 1/2 centre line velocity.
36. On which factor the friction factor for a smooth pipe in turbulent flow depends ?
Ans: Reynolds number.
37. What do you understand by pipe branchings ?
Ans: When water is brought by pipes to a junction where more than two pipes meet, them the
total amount of water brought by pipes to a junction must always be equal to that carried away
from the junction by other pipes, and all pipes that meet at the junction must share the same
pressure at the junction.
38. What is pipe networks and what are the condition for network ?
Ans: Pipe network comprises a number of pipes connected together to form loops and
branches. For a network,
(i) at any junction, Y.Q = 0 and
(ii) between any two junctions the total head loss is independent of the path taken.
39. What is Hardy-Cross Method ?
Ans: It is a commonly used computer program for a pipe network.
40. Explain water hammer.
Ans: The force resulting from changing the speed of the water mass (say in a pipe due to
sudden change of flow rate) may cause a pressure rise in the pipe with a magnitude several
times greater
than the normal static pressure in the pipe. Pressure head caused by water hammer = C (V velocity in pipe, C = celerity).
41. What happens to impurities in centrifugal casting ?
Ans: They get collected at the center of the casting.
42. Define the terms hydraulic similitude and dimensional analysis.
Ans: Hydraulic similitude is the principle on which the model studies are based.
Dimensional analysis is the analysis of the basic relationship of the various physical quantities
involved in the static and dynamic behaviors of water flow in a hydraulic structure.
43. Explain the difference between geometric similarity, kinematic similarity and
dynamic similarity.
Ans: Geometric similarity : It implies similarity of form. The model is a geometric reduction
of the prototype and is accomplished by maintaining a fixed ratio for all homologous lengths
between the model and the prototype.
Kinematic similarity : It implies similarity in motion. Kinematic similarity between a model and
the prototype is attained if the homologous moving particles have the same velocity ratio
along geometrically similar paths. It involves the scale of time as well as length.
Dynamic similarity : It implies similarity in forces involved in motion.
44. Define Reynolds law ?
Ans: When the inertial force and the viscous force are considered to be the only forces
governing the motion of the water, the Reynolds number of the model and the prototype must
be kept at the same value.
45. When a built up edge is formed while machining ?
Ans: While machining ductile materials at high speed.
46. On what factor the friction factor for a rough pipe in turbulent flow depends ?
Ans: Relative roughness.
47. What is unit power of a turbine ?
Ans: PHP12.
48. How cavitation causes damage ?
Ans: In a a closed system (pipelines, or pumps), water vaporises rapidly in regions where the
pressure drops below the vapour pressure. This phenomenon is called cavitation. The vapour
bubbles formed in cavitation usually collapse in a violent manner, which may cause
considerable damage to the system.
49. In milling process, how the arbor torque can be smoothend ?
Ans: Arbor torque can be smoothened by increasing number of teeth, using higher spiral
angle of teeth, using higher cutting depth.
49. What are webs in a twist drill ?
Ans: Webs are the metal column in the drill which separates the flutes.
50. What is bluff body ?
Ans: It is a body with such shape that the flow is separated much ahead of its rear end
resulting in a large wake, the pressure drag being much greater than the friction drag.
51. What is bulk modulus ?
Ans: It is the ratio of hydrostatic stress to volumetric strain within the elastic limits.
52. Define boundary layer.
Ans: It is the fluid layer in the neighborhood of a solid boundary where the effects of fluid
friction are predominant.
53. What is creep flow ?
Ans: It is flow at very low Reynolds number where viscous forces are larger than the inertia
forces.
54. What is Torricellis theorem ?
Ans: According to it velocity of jet flowing out of a small opening is proportional to the square
root of head of liquid above it.
55. How does cavitation manifest itself in a centrifugal pump ?
Ans: Usual symptoms of cavitation of pump are noise, vibration, a drop in head and capacity
with a decrease in efficiency, accompanied by pitting and corrosion of the impeller vanes.
56. What happens if centrifugal pump is operated at excessive speeds ?
Ans: When a pump is operated at excessive speeds, the differential pressure developed
increases and causes a powerful pulsating vacuum on the underside of the blade tips and
each particle of water is pulled away from the blade, taking away with it a small particle of
metal, producing pitting/grooved effect. Repeated erosive action results in complete honey
combing and total destruction of blade, with resultant loss in pump performance.
57. On what parameters the head developed by a centrifugal pump depends ?
Ans: It depends upon the impeller diameter and its rotative speed.
58. Which factors determine the selection of electrolyte for electrochemical
machining process ?
Ans: Electrolyte should be chemically stable and have high electrical conductivity.
59. What is the disadvantages of centrifugal pump having very low specific speed ?
Ans: For a.centrifugal pump having very low specific speed, the impeller diameter is large
and narrow having excessively high disc friction and excessive hydraulic losses.
60. On what factors the efficiency of pump depends ?
Ans: Efficiency of a pump (centrifugal) depends on the size, speed, and proportions of the
impeller and casing.
61. On what factors the cavitation in centrifugal pumps is dependent ?
Ans: Cavitation in centrifugal pumps depends on the velocity of water entering tne impeller
and on the relatiave velocity of the impeller blades where the water is picked up.
62. What are the losses in a centrifugal pump ?
Ans: The losses in a centrifugal pump are : Friction losses due to eddies in flow, leakage,
friction loss due to rotation of impeller in chamber of water, gland and bearing power losses.
63. What should be done to avoid cavitation in pumps ?
Ans: In order to avoid cavitation, the suction lift and the operating speed must be carefully
chosen.
64. What will happen if speed of reciprocating pump is increased ?
Ans: If speed of a reciprocating pump is increased beyond a limit, then atmospheric pressure
would be insufficient to force water into the pump at the same speed as the piston. This would
a break in the continuity of the water in suction pipe (cavitation) and give rise to vibration,
noise, and chemical attack by any dissolved gases which may be released from the water
owing to the high vacuum and the breaking of the water column.
65. What is the order of efficiency of cenetrifugal and reciprocating pumps ?
Ans: The efficiency of centrifugal pump is of the order of 45% whereas that of reciprocting
pump is around %.
66. What are the basic operations performed in a slotter ?
Ans: The different operations done in slotter are :
1. Machining grooves
2. Machining cylindrical surface
3. Machining irregular profiles.
67. How the positive displacement is obtained in rotary pumps ?
Ans: Positive displacement in rotary pumps is achieved in two ways :
(i) A rotor carries radially adjustable vanes, the outer tips of which are constrained by a
circular casing, whose centre is remote from that of the rotor.
(ii) Various combinations of gears, lobes, helices, etc. within a casing arranged so that the
lobes or teeth attached to each rotor pass in sequence through the same pumping space.
68. How a slotter differs from shaper ?
Ans: Slotter Shaper
(a) Ram reciprocates vertically (a) Ram reciprocates horizontally
(b) It has a circular table (b) It has a rectangular table
(c) Suited for machining internal surfaces (c) Suited for machining external surfaces
(d) Table can take less load (d) Table can take much load
69. Under what condition the flow and power of pump vary as square of the size ?
Ans: The flow and power vary as size2 when the geometric size changes as inverse of
change of speed.
70. How the incidence of cavitation detected ?
Ans: The incidence of cavitation is detected by the following in order of appearance.
(i) stroboscopic observation of bubble appearance and size
(ii) sensitive acoustic tests of cavitation noise
(iii) reduction of efficiency and/or head of 3%.
71. How cavitation erosion is assessed ?
Ans: Cavitation erosion is assessed by depth of attack or weight of metal removed.
72. At which temperature the cavitation erosion is negligible and why ?
Ans: Cavitation erosion is negligible at above 300C because the water and steam ha ve
same densities at critical temperature of 374C and thus there is no volume chang e or bubble
collapse in the vicinity of this range.
73. What is an arbor ?
Ans: An arbor is an accurately machined shaft for holding and driving the arbor type cutter. It
is tapered at one end to fit the spindle nose and has two slots to fit the nose keys for locating
and driving it.
74. For a body to float in stable equilibrium where the e.g. should be located w.r.t. metacentre
?
Ans: e.g. should be below metacentre.
75. What is the condition for a flow to be fully developed through a pipe ?
Ans: Ratio of maximum velocity to average velocity should be 2.
76. When a fluid is moving with uniform velocity, whether the pressure of fluid will depend on
its depth and orientation ?
Ans: No.
77. How much is the vertical component of force on a curved surface submerged in a static
liquid ?
Ans: It is equal to weight of the liquid above the curved surface.
78. On which factors depends the friction factor in a rough turbulent flow in a pipe?
Ans: It depends on pipe diameter and the condition of the pipe.
79. What does the realisation of velocity potential in fluid flow indicate ?
Ans: It indicates that flow is irrotational.
80. What is the difference between potential flow and creep flow ?
Ans: Potential flow assumes viscous forces to be zero but same is considered larger than
inertia forces in creep flow.
81. For which application Mach number and Froude numbers are significant ?
Ans: Mach no. is significant in the study of projectiles and jet propulsion. Froude number is
significant in the study of ship hulls.
82. What is the difference between geometric, kinematic, and dynamic similarities between
model and prototype ?
Ans: Geometric similarity is mainly for same shape for model and prototype, kinematic
similarity is concerned with stream line pattern, whereas dynamic similarity concerns the ratio
of forces.
83. A body is floating in water. If it is displaced slightly then about which point it will oscillate.
Ans: It will oscillate about centre of buoyancy.
84. Why uniform ramming is considered desirable in green sand moulding process ?
Ans: Uniform ramming results in greater dimensional stability of a casting.
85. On what account the friction drag is experienced ?
Ans: Friction drag is experienced on separation of boundary layer.
86. What is the characteristic of centrifugally cast components ?
Ans: These have fine grain structure with high density.
87, Under what condition the separation of flow occurs ?
Ans: When pressure gradient changes abruptly.
88. What is the criterion for shaping of streamlined body ?
Ans: It is shaped to suppress the flow separation about the body and to shift the boundary
layer separation to near most part of body to reduce the wake size.
89. What do you understand by entrance length and what is its value for turbulent flow in
smooth pipe ?
Ans: Entrance length of flow is the initial length in which the flow develops fully such that the
velocity profile remains unchanged downstream. For turbulent flow in smooth pipe, entrance
length is taken as 50 x diameter of pipe.
90. Explain the difference between friction drag and pressure drag.
Ans: Friction drag is the drag force exerted by a fluid on the surface due to friction action
when
the flow occurs past a flat surface at zero incidence. Pressure drag is the additional drag
force on
account of the differences of pressure over the body surface when flow occurs past a surface
which is
not everywhere parallel to the fluid stream. Pressure drag depends upon separation of
bondary layer
and the size of wake. Friction drag is due to shear stresses generated due to viscous action.
91. What do you understand by choking in pipe line ?
Ans: When specified mass flow is not able to take place in a pipe line.
92. What is the difference between streamline body and bluff body ?
Ans: In streamline body the shape is such that separation in flow occurs past the nearmost
part of the body so that wake formed is small and thus friction drag is much greater than
pressure drag. In bluff body the flow gets separated much ahead of its rear resulting in large
wake and thus pressure drag is much greater than the friction drag.
93. What is the difference between dressing and trueing of a grinding wheel ?
Ans: Dressing is the process used to clear the cutting surface of the grinding wheel of any
dull grits and embedded swarf in order to improve the cutting action. Trueing is the process
employed to bring the wheel to the required geometric shop and also to restore the cutting
action of a worn wheel.
94. Whether hard grade or softer grade is required for internal grinding than external
grinding?
Ans: Softer graders of wheel are required for internal grinding than for external grinding.
95. How is the velocity profile and stress distribution due to laminar flow of an incompressible
flow under steady conditions in a circular pipe.
Ans: Velocity profile is parabolic with zero velocity at boundary and maximum at the centre.
Shear stress distribution is linear, being maximum at boundary and zero at centre.
96. Where the maximum velocity occurs in open channels ?
Ans: Near the channel bottom.
97. Define hydraulically efficient channel cross section.
Ans: The shape of such section is that which produces minimum wetted perimeter for a given
area of flow and carries maximum flow.
9. What is follower rest ?
Ans .For slender work a travelling or follower rest is used. This fits on the lathe - saddle and
travels to and fro with it. By this means support is constantly provided at the position of cut.
Thus the work piece being turn is rigidly held against the tool.
99. What is the meaning of the term sensitive drill press ?
Ans: A sensitive drilling press is a light, simple, bench type machine for light duty working with
infinite speed ratio.
100. Why carburised machine components have high endurance limit ?
Ans: In carburised machine components, the process of carburisation introduces a
compressive layer on the surface and thus endurance limit is increased.
1. What is anisotropy ?
Ans: The phenomenon of different properties in different directions is called anisotropy.
2. What is vapour pressure and when it becomes important ?
Ans: Vapour pressure is the partial pressure created by the vapour molecules when
evaporation takes place within an enclosed space. It becomes important when negative
pressures are involved.
3. Explain absolute viscosity ?
Ans: It is the ratio of shear stress and the gradient of velocity with distance between a fixed
plate and moving plate (Its unit is Pa . s).
4. Define surface tension ?
Ans: Surface tension of a liquid is the work that must be done to bring enough molecules
from inside the liquid to the surface to form one new unit area of that surface. (Its unit is
Nm/m2 or N/m).
5. What is capillarity and when liquid rises or falls ?
Ans: Capillarity : The rise or fall of a liquid in a capillary tube caused by surface tension.
The magnitude of rise or fall depends on the relative magnitudes of the cohesion of the liquid
and adhesion of the liquid to the walls of the containing vessels. Capillarity is of importance in
tubes smaller
than 10 mm diameter.
Rise of liquid : Liquids rise (in capillary tube) when they wet and adhesion of the liquid to the
walls is greater than the cohesion of the liquid.
Fall of liquid : Liquids fall (in capillary tube) when they do not wet and the cohesion of the
liquid is greater than the adhesion of the liquid to the walls.
6. What is the difference between perfect and real fluids ?
Ans: Perfect fluids are treated as if all tangential forces created by friction can be ignored.
Real fluids refer to the cases in which friction must properly be taken into account.
7. Which factors affect tool size ?
Ans: Following factors influence tool size :
1. Process variable (speed, feed and depth of cut)
2. Tool material
3. Tool geometry
4. Work piece material, its hardness, microstructure and surface condition
5. Cutting conditions.
8. When the motion of fluid is fully known ?
Ans: The motion of a fluid is fully known when the velocity of each of its particles can be
specified.
9. Define fluid.
Ans: A fluid is a substance that can't remain at rest under the action of any shear force.
10. How is the size of a vertical boring machine designated ?
Ans: The specifications of vertical boring machine are :
(i) Column height
(ii) Table size
(iii) Floor area
(iv) Weight of the job
(v) Spindle of the motor.
11. What do you mean by drill sleeve and a drill socket ?
Ans: The drill sleeve is suitable for holding only one size of shank. If the taper shank of the
tool is smaller than the taper in the spindle hole, a taper sleeve is used.
When the tapered tool shank is larger than the spindle taper, drill sockets are used to hold
the tools. Drill sockets are much longer in size than the drill sleeves.
12. What is nonbarotropic fluid ?
Ans: Fluid such as air for which the density is not a single-valued function of the pressure
(aerostatics).
13. On account of which property, the falling drops of rain acquire superical shape.
Ans: Surface tension.
14. How you can definte standard atmospheric pressure ?
Ans: By international agreement, the standard atmospheric pressure is defined as 101.325
kN/m2.
15. What do you understand by acoustic velocity ?
Ans: Accoustic velocity is the speed of a small pressure (sound) wave in a fluid.
16. Explain the difference between centipoise and centistoke ?
Ans: Centipoise is the unit of dynamic viscosity. It is equal to 1/100 of poise, and poise = 0.1
Pa . s. Value of dynamic viscosity of water at 20C is approximately equal to 1 Centipoise.
Centistoke is the unit of kinematic viscosity and is equal to 1/100 x stoke. Stoke is defined as
1 square centimeter per second.
17. What is saybolt seconds universal ?
Ans: Saybolt Seconds Universal (SSU) is the unit of viscosity and is equal to the time
required for a gravity flow of 60 cc through saybolt universal viscometer.
18. Explain difference between cohesion, adhesion and capillarity ?
Ans: Cohesion is the attraction of like molecules.
Adhesion is the attraction of unlike molecules for each other.
Capillarity is the elevation or depression of a liquid surface in contact with a solid.
19. Differentiate between gear hobbing and gear shaping with reference to various relative
37. Explain the difference between horizontal and vertical components of hydrostatic force ?
Ans: The horizontal component of the hydrostatic force on any surface is equal to the normal
force on the vertical projection of the surface and acts through the center of pressure for the
vertical projection.
Vertical component of the hydrostatic force on any surface is equal to the weight of the
volume of liquid abaove the area and passes through the e.g. of the volume.
38. What should be diameter of capillary tube to avoid correction for effect of capillarity in
manometer ?
Ans: Greater than 6 mm.
39. How much hydrostatic pressure acts on a curved surface ?
Ans: The horizontal component of the total hydrostatic pressure force on any surface is
always equal to the total pressure on the vertical projection of the surface, and can be
located through the center of pressure of this projection.
The vertical components of the total hydrostatic pressure force on any surface is always
equal to the weight of the entire water column above the surface extending vertically to the
free surface, and cvan be located through the cemntroid of this column.
40. How much is the horizontal component of force on a curved surface ?
Ans: Force on a vertical projection of the curved surface.
41. State Archimedes principle.
Ans: Any weight, floating or immersed in a liquid, is acted upon by a buoyant force equal to
the weight of the liquid displaced. This force acts through the center of buoyancy, i.e. the e.g.
of the displaced liquid.
42. What do you understand by center of buoyancy ?
Ans: Center of buoyancy is the center of gravity of the displaced liquid and buoyant force
acts through it.
43. How one can establish stability of submerged body and floating body ?
Ans: A submerged body floats in stable equilibrium when the center of gravity of the body lies
directly below the center of buoyancy.
44. What is neutral equilibrium ?
Ans: A submerged body is in neutral equilibrium for all positions when the center of gravity of
body coincides with the center of buoyancy.
45. On what factors the stability of floating objects depends ?
Ans: Stability of floating objects depends upon whether righting or overturning moment is
developed when the center of gravity and center of buoyancy move out of vertical alignment
due to the shifting of position of center of buoyancy.
46. State two products each produced by forward extrusion and reverse impact extrusion.
Ans: Two examples of products made by direct extrusion are : gear profile, solder wire.
Two examples of reverse impact extrusion are : Short tubes of soft alloys, tooth paste
containers.
47. What are the best geometrical shapes suggested for sheet metal drawing and spinning?
Ans: Cup shape is best suited by drawing operation. Conical shape is easiest to produce by
spinning operation.
48. What are the conditions for stability of buoyant bodies ?
Ans: A floating body is stable if the center of gravity is below the metacentre.
A submerged body is stable if the center of gravity is below the center of buoyancy.
49. Define pipe flow ?
Ans: It refers to full water flow in closed conduits of circular cross section under a certain
pressure gradient.
50. How much is vertical component of pressure force on a submerged curved surface ?
Ans: The weight of liquid vertically above the curved surface.
51. Multiple coated, disposable carbide tips have more-or-less replaced brazed carbide
tipped tools in CNC applications. Why ?
Ans: Disposable tips are usually indexable type and have a number of cutting edges. Very
convenient gripping devices for holding such inserts on tool holders are available. A wide
variety of ready made inserts are available which require no grinding or adjustment.
52. State, sequentially elements of a canned CNC drilling cycle.
Ans: Canned cycles are fixed cycles for general sequences of operations. For drilling
operation, sequence of operations will be movement of drill or workpiece to position of actual
drilling, movement of drill downwards till it is in the proximity of workpiece, then movement of
drill at desired feed rate to sufficient depth of hole, retracting the drill above the workpiece.
54. Explain the difference between one and two dimensional flow ?
Ans: True one-dimensional flow occurs when the direction and magnitude of the velocity at all
points are identical. Velocities and accelerations normal to the streamline are negligible. Two
dimensional flow occurs when the fluid particles, move in planes or parallel planes and the
stream-line patterns are identical in each plane.
55. What is the difference between irrotational and rotational flow ?
Ans: Irrotational flow : An ideal fluid flow in which no shear stresses occur and hence no
torques exist. Rotational motion of fluid particles about their own mass centers can not exist. It
can be represented by a flow net.
Rotational flow occurs when the velocity of each particle varies directly as the distance from
settings have to be made to cut a left hand helical gear of same pitch and number of teeth ?
Ans: For cutting right hand helical gear right side of milling table is tilted up from normal
position by the helix angle. For cutting left hand helical gear, right side of table needs to be
tilted down at helix angle, all other settings remaining unchanged.
73. Explain what you understand by the term hydrostatic paradox ?
Ans: Hydrostatic paradox is the phenomenon that the floor load of water in vessels of
different shapes carrying water at same level depends only on the area of the bottom surface
and not on the shape of the vessel.
74. Define buoyancy in brief.
Ans: Buoyancy is the vertical force exerted on the body by the fluid at rest. The buoyancy of
a submerged body in a fluid at rest is equal to the weight of the fluid displaced by the body
and it acts upward through the center of gravity of the displaced volume (the center of
buoyancy).
75. What is the necessary condition for a body to float in stable equilibrium ?
Ans: Meta center should be above the center of gravity.
76. If liquid rotates at constant angular velocity about a vertical axis as a rigid body, then how
its pressure varies at various radial distances ?
Ans: As square of the radial distance.
77. How does the velocity vary along radius in a few vortex ? .
Ans: It decreases with radius.
78. What type of flow will occur when liquid discharges at constant rate through a long,
straight tapering pipe ?
Ans: Steady non-uniform flow.
79. What does continuity equation represent ?
Ans: It relates mass rate of flow along a stream tube.
80. Under what condition steady flow occurs ?
Ans: When conditions do not change with time at any point.
81. Why a drill can not drill deeper than its flute length ?
Ans: If flute submerges in a drilled hole, the chips disposal passage is blocked and the drill
will get jammed in the hole.
82. When do you recommend the use of straight fluted drill ?
Ans: Drills used for brass and other soft materials and thin sheets need not be provided with
any helix angle, to prevent the lips digging into the workpiece.
83. Explain velocity distribution for laminar and turbulent flows.
Ans: In case of laminar flow, the velocity distribution follows a parabolic law of variation. The
maximum velocity at center of pipe is twice the average velocity. For turbulent flow, more
uniform velocity distribution results.
84. In which type of flow the stream lines, streak lines and path lines are identical ?
Ans: In steady flow.
85. Under what condition a drill may not cut ?
Ans: When the cutting lips are not provided with clearance angles. It will cut if 12 clearance
angle is ground.
86. Some drills have straight shanks and some have tapered shank. Why ?
Ans: Small drills (less than 12 mm diameter) are provided with straight shanks which can be
held in Dniren chucks. Bigger drills have tapered shank using self holding Morse tapers which
prevent gravitational fall of drill.
87. What are the main factors that are responsible for the formation of built up edge ?
Ans: The main factors that are responsible for the formation of built up edge are :
1. Extreme pressure in the cutting zone
2. High friction in the tool chip interface
3. High local temperature.
88. In which type of flow the Navier-strokes equation is useful ?
Ans: Viscous flow.
89. Explain the difference between energy line and hydraulic grade line ?
Ans: The energy line is a graphical representation of the energy at each section.
Hydraulic grade line lies below the energy line by an amount equal to the velocity head at the
section.
90. What is the characteristic of equipotential line ?
Ans: It has no velocity component tangent to it.
91. How specific cutting pressure behaves with feed rate and what conclusion can be drawn
from this ?
Ans: As feed rate increases, the specific cutting pressure decreases. It leads to conclude
that feed rates be maximised in metal cutting process.
92. What is hydraulically rough pipe ?
Ans: When Reynolds number is very small, friction factor f becomes independent of the
Reynolds number and depends only on the relative roughness height. Such a pipe behaves
as hydraulically rough pipe.
93. What are the qualities of ideal tool material ?
Ans: It should be hard to resist flank wear and deformation, have high toughness to resist
fracture, be chemically inert to the workpiece, be chemically stable to resist oxidation and
A stagnation point is one at which velocity is zero. Stagnation pressure is the sum of static
pressure and dynamic pressure.
13. What is the hydraulic-grade line ?
It is the line which shows tne variation of piezometric head.
14. Under what condition the thickness of thermal boundary layer and hydrodynamic
boundary layer is same ? When Prandtl number is equal to unity.
15. What keeps the shaft in floating condition in hydrodynamic journal bearing ?
Hydrodynamic pressure developed in the lubricant.
16. Why the elements of higher pairs must be force closed ?
This is necessary to provide completely constrained motion.
17. What is the value of coefficient of friction for ball bearing ?
Ans: 0.1 to 0.25.
18. Why belts are subject to creep ?
Due to uneven extension and contraction of belt.
19. What is the ratio of damping coefficient to critical damping coefficient called ?
Damping factor.
20. In which type of lubrication the starting friction is low ?
In hydrostatic lubrication.
21. Whether Bernoulli's equation is applicable for streamline straight and rotational
flows ?
Ans: Yes.
22. When a plate slides over a parallel plate, what is the relationship between
viscous force and the lubricant thickness ? They are directly proportional.
23. How the stability of empty ship increased.
By adding ballasts at the bottom level.
24. Define Froude number.
It is the square root of ratio of inertia force to gravity force.
25. What for Maning's formula used ?
It is used to determine velocity of flow in pipe.
26. What is the maximum efficiency of power transmission through a pipe ?
Ans: 66.67%.
27. What is the necessary and sufficient condition for bodies in floatation to be in
stable equilibrium ?
Centre of gravity of body should be located below metacentre.
28. Under what condition the thermal boundary layer thickness will be equal to the
hydrodynamic boundary layer thickness ? When Prandtl number is unity.
29. How laminar boundary layer thickness varies on a flat plate ?
It is proportional to the square root of the distance from the leading edge.
30. Name the axial flow reaction turbine with adjustable vanes.
Kaplan turbine.
31. Define the degree of reaction of a turbomachine.
It is the ratio of total pressure change in the rotor to that in the stage.
32. What is meant by relative stability ?
If the system is found to be stable, then it is necessary to know the stable strength or degree
of stability which is called relative stability. Phase margin and gain margins are the measures
of relative stability.
33. On what factors the efficiency of a centrifugal pump depends ?
The efficiency of a centrifugal pump depends on size, speed and type number.
34. Define transducer ?
Transducer is an element which converts the signal from one physical form to another
without changing the information content of the signal.
35. A 200 mm impeller of centrifugal pump develops discharge head of 2 kg/cm2. If
discharge head is required as 8 kg/cm2, what should be diameter of impeller. Ans:
400 mm.
36. Why thin-plate orifice is frequently recommended for flow measurement in most
of the cases ?
It is recommended because of its high accuracy, low cost, and extreme flexibility.
37. How the water flow from a hydrant in a city water system measured ?
It can be measured by allowing the flow of water from a hydrant and noting down the
horizontal distance (x) where jet strikes the ground and the vertical distance (y) of outlet from
ground.
Then flow = area of hydrant x
38. For the same size, length and condition of pipe, how the friction head loss
changes if pipe size is varied.
Under same flow conditions the friction head loss increases as the size change to the 4.8th
power.
39. How does the capacity changes in pipe flow with increase in pipe diameter if
head is constant ?
At constant head, capacity is proportional to d25. .
40. How does the head change in pipe flow with change in diameter, if capacity is
constant.
At constant capacity, head is proportional to
41. How head varies in pipe flow with change in flow, if pipe diameter is same.
At constant diameter, head is proportional to (flow)2.
42. Give some properties of errors ?
(i) Errors give the difference between the measured-value and the true value
(ii) Accuracy of a measurement system is measured in terms of error
(iii) A study of error helps in finding the reliability of the results.
43. Define the term contraction coefficient.
The ratio of area of jet (contracted) and the cross section of the orifice.
44. What for pycnometer is used ?
Pycnometer is used to measure specific gravity of the liquid.
45. How may types of bonded strain gauges used ?
(a) Fine wire strain gauge
(b) Metal foil strain gauge
(c) Piezo resistive gauge.
46. Name various functional elements of an instrumental system ?
(1) Primary sensing element
(2) Variable conversion (or) transducer element
(3) Variable manipulation element
(4) Data transmission element
(5) Data processing element
(6) Data presentation element
(7) Data storage and playback element.
47. Name the three stages of a generalised measuring system.
(i) Sensing and converting the input to a convenient and practicable form.
(ii) Processing/manipulating the measured variable.
(iii) Presenting the processed measured variable in quantitative form.
48. How is a Pelton turbine braked ?
A pelton wheel is braked by a nozzle directing a jet on the back of the buckets.
49. What is static pressure ? How is it measured.
The pressure caused on the walls of a pipe due to a fluid at rest inside the pipe or due to the
flow of a fluid parallel to walls of the pipe is called static pressure. This static pressure is
measured by inserting a pressure measuring tube into the pipe carrying the fluid so that the
tube is at right angle to the fluid flow path.
50. What are the requirements of a control system ?
Stability, accuracy and speed of response are the three requirements of control system.
51. What is the difference between weir, and submerged weir.
Any obstruction of a streamflow over which water flows is weir. When the downstream water
level rises over the weir crest, it is called submerged weir.
52. What is the difference between spillway and siphon spillway ?
Spillway is an essential part of a large dam and provides an efficient and safe means of
releasing flood water that exceeds the design capacity of the reservoir.
Siphon spillway is spillway designed to discharge water in a closed conduit under negative
pressure.
53. What is the difference between culverts, stilling basin, and standpipe ?
Culverts are built at the points of lowest valley to pass water across the embankments of
highways or railroads.
Stilling basin is transitional energy dissipating structure to avoid the damaging process by a
highly accelerated spilled water.
Standpipe is used principally for alleviating the transient pressures in large pipeline system. It
also works as a pressure relief valve for the upstream pipe during the turbine shut off.
54. What do you understand by run-of-river scheme in hydro power generation ?
A scheme in which the discharge is varying and only that much water can be utilised for
conversion as available in the river.
55. What is the difference between firm power and secondary power in hydro power plants ?
The approximate constant and continuous power which is assured at power station and
would be available throughout the year is called firm power.
In run-of-the river schemes which are generally designed for % availability of water, the firm
power would be available for at least % of the years during the life of the scheme. However in
some years discharge in the river may be more than % availability discharge and some extra
power known as secondary power can be generated.
56. What is the criterion for determining economic diameter of power tunnel ?
The economic diameter of a power tunnel is determined such that the total value of following
two factors is least
(i) annual loss of revenue on account of power head lost due to friction.
(ii) recurring annual expenditure.
57. What are the three functions served by a surge tank in a hydro plant ?
The three functions served by a surge tank are
(i) flow regulation - act as a reservoir for acceptance or delivery of water to meet
Ans: 2.
82. Out of centrifugal, axial and positive displacement pumps, which has maximum specific
speed and which has minimum ?
Axial pump has maximum specific speed and reciprocating pump has minimum.
83. Specific speed of a turbine is 800. What type of turbine is this ?
Kaplan turbine.
84. In which type of lubrication system the starting friction is low ?
Hydrostatic lubrication.
85. At which point the cavitation is most likely to occur in a hydel plant ?
At turbine rotor exit.
86. What is the difference between lower pair and higher pair ?
In a kinematic pair, if the elements have surface contact when in motion, the pair is called
lower pair and if elements have line or point contact the pair is called higher pair.
87. What do you understrand by inversions and how many inversions are possible in a
kinematic chain having 'n' links ?
Inversions are different mechanisms obtained by fixing different links in a kinematic chain but
keeping relative motions of links unchanged with respecat to one another. A kinematic chain
with 'n' links can have 'n' inversions.
88. What is the difference between basic kinematic chain and compound kinematic chain ?
What is the criteria for a chain to be constrained ?
A basic kinematic chain consists of four kinematic links and a compound kinematic chain is a
constrained chain of more than four links. A chain is constrained if no. of binary joints and half
of number of higher pairs is equal to 3/2 of no. of links minus 2.
89. What is the difference between a machine and a mechanism ?
A mechanism consists of links forming a constrained kinematic chain. Its function is basically
to transmit or modify motion. A machine is a mechanism but here we are concerned with
forces to be transmitted and it is used to modify mechanical work.
90. In which type of motion, acaceleration is directly proportional to displacement ?
SHM.
91. What is the function of a transducer element ?
The function of a transducer element is to sense and convert the desired input into a more
convenient and practicable form to be handled by measurement system.
92. What is the direction of tangential acceleration ?
The direction of tangential acceleration may be same or opposite to that of angular velocity.
93. What is the number of degrees of freedom constrained in each case by the kinematic
pairs.
(i) Itevolute pair, (ii) cylindrical pair, (iii) Screw pair, (iv) Spherical pair.
Ans: (i) Revolute pairsingle degree of freedom.
(ii) cylindrical pairtwo degrees of freedom.
(iii) Screw pairone degree of freedom.
(iv) spherical pairthree degrees of freedom.
94. What is the purpose of D-slide valve in steam engines ?
It controls the piston position for cut off of steam, for release of steam and compression
position for steam in cylinder.
95. What is the purpose of Corliss valve in place of D'-slide valve in steam engine ?
Corliss valve reduces condensation, provides independent control on admission, cut off,
release and compression, and reduces driving power requirements.
96. On what factor the size of cam depends ?
Size of cam depends on base circle.
97. If base circle diameter of cam increases, what happens to pressure angle ?
It decreases.
98. If angular speed of cam is increased two times, how much jerk will be increased ?
Eight times.
99. Define primary and secondary transducers ?
A primary transducer senses a physical phenomena and converts it to an analogous output.
The analogous output is then converted into an electrical signal by secondary transducer.
100. What is the relationship between (i) axes of spin, precession, and applied gyroscopic
torque and (ii) in between their planes ?
The axes of spin, precession, and applied gyroscopic torque are contained in two planes
perpendicular to each other, and planes of spin, precession, and applied gyroscopic torque in
the three planes perpendicular to one another.
3. Materials which absorb neutrons and produce fissionable material are called ?
Ans: Fertile materials, such as U28 and Th22.
4. What is the process which produces fissionable material from a fertile material ?
Ans: Breeding.
5. What is burn up in connection with fissionable material ?
Ans: Burn up corresponds to destruction of fissionable material when it undergoes nuclear
fission.
6. What kind of nuclear fuel is used in Narora, Kalapakkam and Rana Pratap Sagar
nuclear plants ?
Ans: Natural uranium.
7. Which type of plant will you recommend for remote location if power is required in
six to twelve months time ?
Ans: Diesel engine power plant.
8. Under what condition a nuclear reaction is said to be critical ?
Ans: For critical condition, the reaction should continue at a steady rate which is possible
when rate of production of neutrons is same as the combined rate of absorption of neutrons
and the rate of leakage of neutrons.
9. If a nuclear reactor generates more fuel that it consumes, it is called ______ ?
Ans: Fast breeder reactor.
10. Natural uranium contains only 0.7% U25 which is capable of switching chain
nuclear reaction. How this percentage is increased ?
Ans: Percentage of U25 in natural uranium is increased by a process called uranium
enrichment.
11. Why the vane passages are gradually increased in size in successive wheels in steam
turbine ?
Ans: The velocity of steam decreases in successive stages and to accommodate same flow
per unit time, the area of flow must increase.
12. At what pressure and temperature the density of water and steam is same ?
Ans: At 225 kg/cm2 and 74.6 C.
13. What is the latent heat of evaporation at critical point ?
Ans: Zero.
14. How much space steam will occupy at atmospheric pressure corresponding to 1 kg of
water ?
Ans: 100 times the space occupied by 1 kg of water.
15. What is meant by quality of steam ?
Ans: It refers to amount of unevaporated moisture in steam. If steam is perfectly dry, it's
quality is 100%.
16. What is diagram efficiency in steam turbine ?
Ans: Diagram efficiency = Change in K.E./kg / Energy suppled/kg.
17. What do you understand by effectiveness of heat exchanger ?
Ans: Effectiveness of heat exchanger = actual heat transfer/maximum possible heat transfer.
18. If superheat and condenser temperatures are unchanged and if pressure of steam is
increased, then what happens to dryness fraction of steam after isentropic expansion ?
Ans: It will decrease.
19. As pressure of steam is increased, why reheating is necessary?
Ans: As pressure is increased, the dryness fraction of steam lowers on isentropic expansion.
Therefore, steam has to be reheated after partial expansion so that dryness fraction remains
within limits after expansion.
20. What is boundary layer thickness in free convection case ?
Ans: Velocity of fluid flow at solid surface is zero and it increases rapidly as distance from
solid surface becomes greater, reaches a maximum value and then decreases to that of
undisturbed fluid. The distance between the solid surface and point where boundary layer
velocity equals undisturbed flow (edge) is called boundary layer thickness.
21. What do you understand by forced convection ?
Ans: When convection heat transfer occurs between a solid body and a fluid and where
circulation of fluid is caused and controlled by some mechanical.
22. In radiative heat transfer, a gray surface is one whose emissivity is _____ ?
Ans: Independent of wavelength.
23. What is the effect of water injection and steam injection in gas turbine of heat rate and
power output ?
Ans: Water injection results in higher mass flow rate through turbine section and as rich
electrical output is increased. However it increases gas turbine heat rate because of the
additional heat consumption required to vaporise the water.
Steam injection increases power output and decreases heat rate because of its higher energy
entering the combustion zone.
24. Water/steam injection in gas turbines increases power output. What is the limit and
reasons for same ?
Ans: Water/steam injection is not allowed beyond 5% of compressor flow to avoid flame out in
combustion and to minimise operating cost and impact on inspection intervals.
25. What are the advantages and drawbacks of centrifugal compressor and axial flow
surrounding objects.
29. Why high latent heat of vaporisation is desirable in a refrigerant ?
Ans: A high latent heat of vaporisation of refrigerant results in small amount of refrigerant
and thus lesser circulation system of refrigerant for same tonnage.
30. What is the critical temperature of a refrigerant ?
Ans: Critical temperature is the maximum temperature of a refrigerantrat which it can be
condensed into liquid and beyond this it remains gas irrespective of pressure applied.
31. Maximum combustion temperature in gas turbines is of the order of 1100 to 10C whereas
same is around 00C in I.C. engine ? Why ?
Ans: High temperature in I.C. engine can be tolerated because it lasts for a fraction of
second but gas turbines have to face it continuously which metals can't withstand.
32. Why efficiency of gas turbines is lower compared to I.C. engines ?
Ans: In gas turbines, 70% of the output of gas turbine is consumed by compressor. I.C.
engines have much lower auxiliary consumption. Further combustion temperature of I.C.
engines is much higher compared to gas turbine.
33. What do you understand by timed cylinder lubrication ?
Ans: For effective lubrication, lub oil needs to be injected between two piston rings when
piston is at bottom of stroke so that piston rides in oi during upward movement. This way lot of
lub oil can be saved and used properly.
34. What is IIUCR in relation to petrol engine ?
Ans: HUCR is highest useful compression ratio at which the fuel can be used in a specific test
engine, under specified operating conditions, without knocking.
35. In some engines glycerine is used in place of water for cooling of engine. Why ?
Ans: Glycerine has boiling point of 90C which increases its heat carrying capacity. Thus
weight of coolant gets reduced and smaller riadiator can be used.
36. Why consumption of lubricating oil is more in two-stroke cycle petrol engine than fourstroke
cycle petrol engine ?
Ans: In two-stroke engine lub oil is mixed with petrol and thus some lub oil is blown out
through the exhaust valves by scavenging and charging air. There is no such wastage in four
stroke petrol engine.
37. As compression ratio increases, thermal n increases. How is thermal n affected by weak
and rich mixture strength ?
Ans: Thermal n is high for weak mixture and it decreases as mixture strength becomes rich.
38. How engine design needs to be changed to burn lean mixture ?
Ans: Engine to burn lean mixture uses high compression ratio and the highly turbulent
movement of the charge is produced by the geometry of the combustion chamber.
39. Horse power of I.C. engines can be expressed as RAC rating, SAE rating, or DIN rating.
To which countries these standards belong ?
Ans: U.K., USA and Germany respectively.
40. What is the use of flash chamber in a vapour compression refrigeration cycle to improve
the COP of refrigeration cycle ?
Ans: When liquid refrigerant as obtained from condenser is throttled, there are some
vapours. These vapours if carried through the evaporator will not contribute to refrigerating
effect. Using a flash chamber at some intermediate pressure, the flash vapour at this
pressure can be bled off and fed back to the compression process. The throttling process is
then carried out in stages. Similarly compression process is also done in two separate
compressor stages.
41. Why pistons are usually dished at top ?
Ans: Pistons are usually hollowed at top to (i) provide greater spa'e for combustion, (ii)
increase surface for flue gases to act upon, and (iii) better distribution of stresses.
42. What is the function of thermostat in cooling system of an engine ?
Ans: Thermostat ensures optimum cooling because excessive cooling decreases the overall
efficiency. It allows cooling water to go to radiator beyond a predetermined temperature.
43. What are the causes of failure of boiler tubes ?
Ans: Boiler tubes, usually are made from carbon steel and are subject to (a) high rates of
heat transfer, (b) bending stresses due to uneven heating, especially at expanded or welded
joints into headers or drums, (c) external erosion from burners and flue gas, (d) possible
corrosion on the boiler side, and (e) occasional manufacturing defects.
Failure may occur due to following reasons :
(a) High thermal ratings may lead to rapid failure if the internal fluid flow is reduced for any
reason. The resultant overheating leads to a failure by creep, characterised by the bulging of
the tube with the eventual development of a longitudinal split.
(b) Fatigue cracking due to bending stresses occur. These are associated with change of
section and/or weld undercut, where tubes are expanded or welded into headers.
(c) Failure may arise due to overstressing of a reduced section of metal.
(d) Sudden failure of the boiler tube due to corrosion arises from embrittlement of the
carbon steel due to interaction between atomic hydrogen from the corrosion process and the
iron carbide present in the steel.
(e) Defects in tube manufacture, although far from being a regular occurrence, can be a
cause of serious trouble. Lamination in boiler tubes or score marks arising from the cold
drawing of tubes, give rise to premature failure and may promote corrosion at these regions.
44. What are the causes of failure of superheater tubes ?
Ans: Superheater tubes are subjected to the most severe combination of stress, temperature
and corrosive environment. In addition to high-temperature strength, resistance to corrosion
is also important. For example, low-alloy ferritic steel such as -1/% Cr, 1% Mo would not be
used at metal temperatures above 580C because of inadequate resistance to corrosi on and
oxidation over a full service life of 100,000/150,000 hr.
Failures in superheater tubes may arise from :
(a) Prior fabrication history (b) Faulty heat treatment
(c) Consequences of welding (d) Overheating of the tube metal
(e) Gas-side corrosion (f) Stress corrosion (austenitic steels).
45. Why supercritical boilers use less amount of steel compared to non-supercritical boilers ?
Ans: Supercritical boilers do not head heavy drum for separation of steam from mixture of
water and steam.
46. Out of electric heater and heat pump, which is economical in operation ?
Ans: Heat pump.
47. Which furnace burns low-ash fusion coal and retains most of the coal ash in the slag?
Ans: Cyclone furnace.
48. How the thickness of thermal boundary layer and thickness of hydrodynamic boundary
layer related ?
Ans: Ratio of their thickness = (Prandtl number)-1/3.
49. What is the effect of friction on flow of steam through a nozzle ?
Ans: To decrease both mass flow rate and wetness of steam.
50. Why gas turbine power plant needs efficient compressor ?
Ans: Because a large portion of turbine work is eaten away by compressor and its
inefficiency will affect net power output and cost of generation.
51. Why rockets using liquid hydrogen have higher specific impulse compared to liquid
hydrocarbon ?
Ans: Liquid hydrogen has higher burning velocity.
52. Why axial flow compressor is preferred for gas turbines for aeroplanes ?
Ans: Because it has low frontal area.
53. What is the effect of inter cooling in gas turbines ?
Ans: It decreases thermal efficiency but increases net output.
54. Why iso-octane is chosen as reference fuel for S.I. engines and allotted 100 value for its
octane number ?
Ans: Iso-octane permits highest compression without causing knocking.
55. Why thermal efficiency of I.C. engines is more than that of gas turbine plant ?
Ans: In I.C. engine maximum temperature attained is higher than in gas turbine.
56. Which are the reference fuels for knock rating of S.I. engines ?
Ans: n-heptane and ISO-octane.
57. When effect of variations in specific heats is considered then how do maximum
temperature and pressure vary compared to air standard cycle ?
Ans: Temperature increases and pressure decreases.
58. Quantities like pressure, temperature, density, viscosity, etc. are independent of mass.
What are these called ?
Ans: Intensive properties.
59. The amount of radiation emitted per scm per sec is called .... ?
Ans: Emissive power.
60. In convection heat transfer, if heat flux intensity is doubled then temperature
difference between solid surface and fluid will ?
Ans: Get doubled.
61. How you can define coal ?
Ans: Coal is a naturally occurring hydrocarbon that consists of the fossilised remains of
buried plant debris that have undergone progressive physical and chemical alteration, called
coalification, in the course of geologic time.
62. Which pollutant is major greenhouse gas and what is its effect ?
Ans: CO is major greenhouse gas and it traps the radiation of heat from the sun within
earth's atmosphere.
63. In order to increase efficiency and reduce CO emissions and other emissions, clear coal
technologies are receiving major attention. What are these ?
Ans: (i) Advanced pulverised and pressurised pulverised fuel combustion.
(ii) Atmospheric fluidised bed combustion and pressurised fluidised bed combustion.
(iii) Supercritical boilers.
(iv) Integrated gasification combined cycle systems.
(v) Advanced integrated gasification, including fuel cell systems.
(vi) Magneto hydrodynamic electricity generation.
64. What are the important operational performance parameters in design of fuel firing
equipment ?
Ans: Fuel flexibility, electrical load following capability, reliability, availability, and maintenance
ease.
65. What is the differenc between total moisture and inherent moisture in coal ?
Ans: The moisture content of the bulk as sampled is referred to as total moisture, and that of
the air dried sample is called inherent moisture.
66. Proximity analysis of coal provides data for a first, general assessment of a coal's quality
and type. What elements it reports ?
Ans: Moisture, volatile matter, ash and fixed carbon.
67. Ultimate analysis of coal is elementary analysis. What it is concerned with ?
Ans: Carbon, hydrogen, nitrogen, and sulphur in coal on a weight percentage basis.
68. Explain the difference between AFBC, BFBC, PFBC and PCFB in regard to fluidised bed
technologies.
Ans: AFBC (Atmospheric fluidised bed combustion) process consists of forming a bed of inert
materials like finely sized ash or ash mixed with sand, limestone (for sulphur removal), and
solid fuel particles in a combustor and fluidising it by forcing combustion air up through the
bed mixture. The gas flows thorugh bed without disturbing particles significantly but gas
velocity is high enough to support the total weight of bed (fluidisation). At slightly higher
velocity excess gas passes through the bed as bubbles (fluidised bed) and gives the bed the
appearance of a boiling liquid.
Bubbling fluidised bed combustion (BFBC) has a defined height of bed material and operates
at or near atmospheric pressure in the furnace.
Pressurised fluidised bed combustion (PFBC) system operates the bed at elevated pressure.
Exhaust gases have sufficient energy to power a gas turbine, of course, gases need to be
cleaned.
In fluidised combustion, as ash is removed some unburned carbon is also removed resulting
in lower efficiency. In circulating fluidised bed combustion (CFBC) system, bed is operated at
higher pressure leading to high heat transfer, higher combustion efficiency, and better fuel
feed. Circulating fluidised beds operate with relatively high gas velocities and fine particle
sizes. The maintenance of steady state conditions in a fast fluidised bed requires the
continuous recycle of particles removed by the gas stream (circulating bed). The term
circulating bed is often used to include fluidised bed systems containing multiple
conventional bubbling beds between which bed material is exchanged.
69. What for Schmidt plot for is used in heat transfer problems ?
Ans: Schmidt plot is a graphical method for determining the temperature at any point in a
body at a specified time during the transient heating or cooling period.
70. In which reactor the coolant and moderator are the same ?
Ans: Pressurised water reactor.
71. Which reactor has no moderator ?
Ans: Fast breeder reactor.
72. What are thermal neutrons ?
Ans: Thermal neutrons are slow neutrons (having energy below 1 eV) which are in thermal
equilibrium with their surroundings.
73. What is big advantage of fast breeder reactor ?
Ans: It has rapid self breeding of fissile fuel during the operation of the reactor, and thus, it
offers about sixty times the output with same natural uranium resources through ordinary nonbreeder
nuclear reactor.
74. What is the purpose of biological shield in nuclear plants ?
Ans: Biological shield of heavy concrete prevents exposure to neutrons, beta rays and
gamma rays which kill living things.
75. Which two elements have same percentage in proximate and ultimate analysis of coal?
Ans: Moisture and ash.
76. On which analysis is based the Dulong's formula for the heating value of fuel ?
Ans: On ultimate analysis.
77. Which element causes difference in higher and lower heating values of fuel ?
Ans: Hydrogen.
78. Which heating value is indicated by a calorimeter and why ?
Ans: Gross heating value because steam is condensed and heat of vapour formed is
recovered.
79. State the difference between ultimate and proximate analysis of coal ?
Ans: In ultimate analysis, chemical determination of following elements is made by weight:
Fixed and combined carbon, H, O, N, S, water and ash. Heating value is due to C, H and S.
In proximate analysis following constituents are mechanically determined by weight. Moisture,
volatile matter, fixed carbon and ash. Heating value is due to fixed carbon and volatile matter.
80. What is fuel ratio ?
Ans: Fuel ratio is the ratio of its % age of fixed carbon to volatile matter.
81. How the analyses and calorific values of fuels can be reported ?
Ans: It may be reported as
(a) as received or fired (wet) basis
(b) dry or moisture free basis
(c) combustible or ash and moisture free basis
82. What is the difference between nuclear fission and fission chain reaction.
Ans: The process of splitting of nucleus into two almost equal fragments accompanied by
release of heat is nuclear fission. Self sustained, continuing, sequence of fission reactions in
a controlled manner is fission chain reaction.
83. Explain difference between fissile and fertile materials.
Ans: The materials which can give nuclear fission e.g. U 35, Pu 39, U 33 are fissile
materials. Fertile material itself is not fissionable, but it can be converted to a fissionable
material by irradiation of neutrons in a nuclear reactor.
84. What do you understand by fuel cycle in nuclear plants ?
Ans: Fuel cycle a series of sequential steps involved in supplying fuel to a nuclear power
reactor. The steps include : Mining, refining uranium, fabrication of fuel elements, their use in
nuclear reactor, chemical processing to recover remaining fissionable material, re-enrichment
of fuel from recovered material, refabrication of new fuel elements, waste storage etc.
85. What is heavy water and what is its use in nuclear plants ?
Ans: Water containing heavy isotopes of hydrogen (Deuterium) is known as heavy water.
Heavy water is used as a moderator. Heavy water has low cross section for absorption of
neutrons than ordinary water. Heavy water slows down the fast neutrons and thus moderates
the chain reaction.
86. What is a converter reactor ?
Ans: A reactor plant which is designed to produce more fuel than it consumes. The breeding
is obtained by converting fertile material to fissile material.
87. Explain nuclear reactor in brief.
Ans: A plant which initiates, sustains, controls and maintains nuclear fission chain reaction
and provides shielding against radioactive radiation is nuclear reactor.
88. What is the difference between conversion and enrichment ?
Ans: The process of converting the non fissile U 38 to fissile U-35 is also called "Conversion".
The material like U 38 which can be converted to a fissile material by the neutron flux is called
"fertile material". The conversion is obtained within the nuclear reactor during the chain
reaction.
Enrichment is the process by which the proportion of fissile uranium isotope (U-35) is
increased above 0.7% (original % in natural uranium).
The concentration of U-35 in the uranium hexafluoride is increased from the 0.7% in natural
uranium to to 4%. This is called enrichment and is accomplished in an enrichment plant.
89. Disposal of radioactive waste materials and spent fuel is a major and important
technology. How the waste radioactive material is disposed off ?
Ans: Nonusable fission products are radioactive and take short/medium/long time for
radioactive decay to reach safe level of radioactivity. Accordingly three methods of disposal
are :
(a) Zero or low radioactivity material is dispersed or stored without elaborate shielding.
(b) Medium radioactivity material is stored for short duration of about 5 years to allow decay
of radioactivity.
(c) High radioactive material. They are stored in water for several months to permit
radioactive decay to an accepetable low level.
90. Which nuclear reactor uses water as a coolant, moderator and reflector ?
Ans: Pressurised water reactor.
91. Which reactor produces more fissionable material than it consumes ?
Ans: Breeder reactor.
92. Which reactor uses natural uranium as fuel ?
Ans: Gas cooled reacator.
93. Which reactor uses heavy water as moderator ?
Ans: CANDU.
94. Which reactor requires no moderator ?
Ans: Breeder reactor.
95. Which reactor uses primary coolant as fluoride salts of lithium, beryllium, thorium and
uranium ?
Ans: Molten salt breeder reactor.
96. Why an increase in area is required to produce an increase of velocity in case of
supersonic flow ?
Ans: Increase in area for increase in velocity for supersonic flow is required because the
density decreases faster than velocity increases at supersonic speeds and to maintain
continuity of mass, area must increase.
97. Under what circumstances would there be an increase in pressure in a divergent nozzle
?
Ans: For subsonic flow at inlet section of a diffuser a lower velocity and higher pressure will
exist at the exit section. For supersonic isentropic flow at the inlet section a higher velocity
and lower pressure will exist at the exit but if a shock wave occurs in the diffuser then a higher pressure will exist at the exit.
98. Why water can't be used as refrigerant for small refrigerating equipment ?
Ans: The refrigerant should be such that vapour volume is low so that pumping work will be
low. Water vapour volume is around 4000 times compared to R- for a given mass.
99. Which parameter remains constant in a throttling process ?
Ans: Enthalpy.
100. What is the difference between isentropic process and throttlinglprocess ?
Ans: In isentropic process, heat transfer takes place and in throttling process, enthalpy
before and after the process is same.