1:119
December 2008
W3735-1
W3745-1
Introduction
Features
D100006X012
www.emersonprocess.com/regulators
Bulletin 71.1:119
Specifications
Body Sizes and End Connection Styles(1)
3/4, 1, or 1-1/4-inch NPT
Construction Materials
Standard Construction
Valve Body: Cast iron
Spring Case: Aluminum
Bonnet: Aluminum
Disk Holder Assembly: Aluminum and Nitrile (NBR)
(standard), Stainless steel and Nitrile (NBR) or
Stainless steel and Fluorocarbon (FKM)
Orifice: Aluminum (standard) or Stainless steel
Diaphragm: Nitrile (NBR) or Fluorocarbon (FKM)
O-Rings: Nitrile (NBR) (standard) or
Fluorocarbon (FKM)
Stem Wiper: Polytetrafluoroethylene (PTFE)
Adjusting Screw: Steel
Spring: Steel
NACE Construction
Body: Steel
Disk Holder Assembly: Aluminum/
Fluorocarbon (FKM)
Diaphragm/Stem Assembly: Aluminum/
Fluorocarbon (FKM)
O-Rings and Internal Retaining Rings:
Fluorocarbon (FKM)
Approximate Weight
6 pounds (3 kg)
1. End connections threaded to various national or international thread standards can usually be supplied. Contact the local Sales Office.
2. The pressure and temperature limits in this bulletin and any applicable code limitation should not be exceeded.
Installation
The Type 119 control valve may be installed in any
position, but normally the actuator is vertical above
the valve body. Install the valve body such that
the direction of the process flow matches the flow
direction arrow on the side of the body.
Each control valve has a screened vent in the spring
case and in the valve bonnet. On indoor installations,
these vents should be piped outdoors with the shortest,
straightest pipe of the largest practical diameter.
(0,21 to 1,0)
(0,34 to 1,4)
(0,34 to 2,4)
(2,1 to 4,1)
spring
part number
spring
color code
1D892327022
1D751527022
1D665927022
1D7455T0012
Red
Silver
Blue
Green
Bulletin 71.1:119
Universal NACE Compliance
4.12
(105)
Ordering Information
8.00
(203)
MAXIMUM
3/4, 1, OR
1-1/4-INCH NPT
Application Information
1. Controlled fluid
a. Type (include chemical analysis, if possible)
b. Temperature (normal and maximum anticipated)
c. Specific gravity
2.12
(54)
INCHES
(mm)
4.00
(102)
A2952-1
Figure 3. Dimensions
4. Flow rates
a. Minimum controlled flow
b. Normal flow
c. Maximum flow
3/16 (4,8)
orifice size,
inch (mm)
3/4-inch body
1-inch body
1-1/4-inch Body
Cv
Cg
C1
Cv
Cg
C1
Cv
Cg
C1
1/8 (3,2)
0.43
12.5
29.1
0.43
12.5
29.1
0.43
12.5
29.1
3/16 (4,8)
0.95
27.8
29.3
0.95
27.8
29.3
0.95
27.8
29.3
1/4 (6,4)
1.70
48.3
28.4
1.70
48.3
28.4
1.70
48.3
28.4
5/16 (7,9)
2.64
76.5
29.0
2.64
76.5
29.0
2.64
76.5
29.0
3/8 (9,5)
3.22
104
32.3
3.3
105
31.8
3.57
106
29.7
1/2 (13)
4.7
176
37.4
5.0
178
35.6
5.75
183
31.8
9/16 (14)
5.6
213
38.0
5.9
218
36.8
7.2
230
31.9
Bulletin 71.1:119
Industrial Regulators
TESCOM
USA - Headquarters
McKinney, Texas 75069-1872 USA
Tel: 1-800-558-5853
Outside U.S. 1-972-548-3574
USA - Headquarters
McKinney, Texas 75069-1872 USA
Tel: 1-800-558-5853
Outside U.S. 1-972-548-3574
USA - Headquarters
Elk River, Minnesota 55330-2445 USA
Tel: 1-763-241-3238
Asia-Pacific
Shanghai, China 201206
Tel: +86 21 2892 9000
Asia-Pacific
Singapore, Singapore 128461
Tel: +65 6777 8211
Europe
Bologna, Italy 40013
Tel: +39 051 4190611
Europe
Bologna, Italy 40013
Tel: +39 051 4190611
Gallardon, France 28320
Tel: +33 (0)2 37 33 47 00
Europe
Selmsdorf, Germany 23923
Tel: +49 (0) 38823 31 0
Emerson Process Management Regulator Technologies, Inc., 1990, 2008; All Rights Reserved