PIPES
XINXING
PIPES
Product
Technical Manual
Contents
Company Profile
Company Profile
Xinxing Ductile Iron Pipes Co., Ltd., as a subsidiary of Xinxing Cathay International Group Co.,Ltd, adheres
to the orientation of science and technology, environmental protection, quality and efficiency. At present,
it has grown into a trans-regional and multi-industrial enterprise group integrating such wide industries as
ductile iron pipe, steel and machinery, as well as various areas such as scientific research, production and
trade. In 1997, Xinxing was listed on the Shenzhen Stock Exchange of China and has been selected as the
Top 50 Most Promising Listed Companies for 8 consecutive years since then. Xinxing is primarily engaged
in the centrifugal casting ductile iron pipes and fittings, steel smelting and rolling processing, special steel
pipes, and foundry products, etc. At present, it has grown into an integrated processing enterprise with the
annual output of more than 10 million tons of metal products, including eight major series, i.e. Xinxing ductile
iron pipes, Xinxing steel, Xinxing special steel pipes, Xinxing gratings, Xinxing castings, Xinxing steel-plastic
composite pipes, with the annual output of 8.0 million tons of steel, 1.8 million tons of ductile iron pipes,
40,000 tons of ductile iron fittings, 180,000 tons of special steel pipes, 3,000,000 m steel-plastic composite
pipes and 80,000 tons of steel gratings. It has established production bases in Handan of Hebei, Wuhu of
Anhui, Bazhou of Xinjiang, Huangshi of Hubei, Taojiang of Hunan, and Chongzhou of Sichuan, etc.
XINXING PIPES
fields.
e l e c t r i c p o w e r, p e t r o l e u m , c h e m i c a l ,
Quality Assurance.
01
Chapter I ,
Ductile Iron
Pipe Joint and
Anti-corrosion
Solution
02
XINXING PIPES
03
Chapter I ,
Ductile Iron
Pipe Joint and
Anti-corrosion
Solution
13
18
04
XINXING PIPES
05
Ductile iron material features similar mechanical properties with carbon steel, such as high mechanical
strength and good ductility, and the same anti-corrosion performance as cast iron. Therefore, ductile iron
pipe has gradually become one of the most secure and reliable pipes in the water supply and drainage area
Xinxing ductile iron pipes can be graded by the wall thickness class coefficient K or pressure class C.
Xinxing Ductile Iron Pipes Co., Ltd. provides ductile iron pipe products ranging from DN80 ~ DN2600 in
accordance with ISO2531/7186 or EN545/598. Meanwhile, it can provide the most appropriate joints and
EN 545/EN 598
internal and external anti-corrosion solutions according to the pipeline laying and using conditions. For
GB/T 13295, GB/T 26081 and other related standards for ductile iron pipes
Note: The wall thickness class coefficient K (or pressure class C) shall be specified in the agreement
between the supplier and the purchaser.
Flexible joint
Self-anchored joint
Rigid
Specification Range
Internal lining
External Coating
polyethylene finishing
T-type joint
DN80~2000
XT2-type joint
DN80~2600
TF joint
DN80~1200
layer
Xanchor joint
DN1400~2000
Polyurethane lining
Zinc+epoxy coating
DN80~2000
Polyurethane coating
KWall thickness class coefficient, selected from a series of whole numbers ...9,10,11,12...
DN250~2000
The minimum nominal wall thickness of centrifugal casting ductile iron pipe is 6mm, and the minimum wall
thickness of non-centrifugal casting ductile iron pipe and fittings is 7 mm; the tolerance on thickness for
pipes and fittings is shown in the table below.
Table 2 Limit Deviation on Nominal Wall Thickness for Pipes and Fittings (Unit: mm)
Type of casting
Pipes centrifugally cast
Limit Deviation
-1.3
-(1.3+0.001DN)
-2.3
-(2.3+0.001DN)
06
XINXING PIPES
07
emin=
Where
PFA SF DE
20Rm+ PFASF
Sealing principle
Structure of T-type joint is shown in Figure 1. During joint installation, the external spigot is extruded on
the rubber ring inside the socket.The compression deformation can generate a certain degree of contact
pressure. And it is the so-called self-sealing action of the rubber ring that keeps the joint tight. The selfsealing effect means, when the rubber ring is under the fluid pressure, the actual contact pressure on the
rubber ring is the sum of the contact pressure of the pre-compressed rubber ring and the new contact
Tolerance
+1.3+0.001DN
Pipes Non-centrifugally
Cast and fittings
+2.3+0.001DN
pressure on the rubber ring brought by the fluid pressure. Since the contact pressure is higher than the fluid
pressure, so that the joint is well tightened.
Joint features
The joint features simple structure, easy installation and sound sealing performance. The positioning of
sealing ring and deflection of joint are taken into consideration during socket structure design. By controlling
the insertion depth of the spigot, the joint can have certain axial flexibility. Therefore this type of joint is able
to adapt to certain foundation settlement, while long-distance deflection of pipeline can be achieved through
its deflection angle . Joint deflection installation is shown in Figure 2.
The rubber ring consists of two parts, i.e. the hard rubber and soft rubber. The hard rubber can support and
align the pipe joints, and greater thrust is needed during installation.
Specification Range
DN80~DN300
C40
DN350~DN600
C30
blocks to resist the axial forces should be set at the bend of pipeline, or
DN700~DN2000
C25
08
XINXING PIPES
09
The main technical parameters of T-type joint ductile iron pipe are shown in Figure 3 and Table 5:
enom
DE
Lu
Figure 3 T-type joint ductile iron pipe
C-Class
DE
Lu
(mm)
(mm)
(mm)
()
(mm)
80
98
140
85
100
118
163
88
125
144
190
91
150
170
217
94
200
222
278
100
6.3
62
4.7
250
274
336
105
6.8
54
5.5
300
326
393
7.2
49
6.2
350
378
448
7.7
45
6.3
400
429
500
8.1
42
6.5
450
480
540
8.6
40
6.9
500
532
604
38
7.5
600
635
713
9.9
36
8.7
700
738
824
150
10.8
34
8.8
800
842
943
160
11.7
32
9.6
Application Field
900
945
1052
175
12.6
31
10.6
1000
1048
1158
185
13.5
30
11.6
1100
1152
1267
200
14.4
29
12.6
1200
1255
1377
215
1400
1462
1610
239
1500
1565
1710
250
1600
1668
1820
262
18.9
1800
1875
2050
300
20.7
2000
2082
2266
319
22.5
DN
110
120
enom(mm)
PFA
(bar)
64
6000
15.3
17.1
6000/8150
18
enom(mm)
27
26
(bar)
4.4
Sealing principle
4.4
4.5
4.5
28
PFA
13.6
30
25
Installation method
15.7
16.7
17.7
installation.
19.7
21.8
10
XINXING PIPES
11
enom
DE
Locking Ring
Gland
Bolts and Nuts
Lu
DN
DE
(mm)
D
(mm)
P
(mm)
80
98
140
92.5
100
118
163
94.5
150
170
217
100.5
200
222
278
250
274
336
300
326
393
350
378
400
()
Lu
(mm)
K9
enom(mm)
C-Class
PFA
(bar)
6
5
64
enom(mm)
PFA
(bar)
Joint structure
4.4
As shown in Figure 6, TF self-anchored joint adopts the T-joint sealing structure. Compared with T-joint, it
4.4
adds a welded bead on spigot, an open-end locking ring, a special gland and connecting bolts to provide the
4.5
40
joint with good anti-slippage performance. The locking ring and the gland can slide between each other, so
6.3
62
4.7
6.8
54
5.5
Working principle
107.5
7.2
49
6.2
The axial thrust forces generated at the bending places and tees of the pressure pipeline will cause the
448
110.5
7.7
45
6.3
socket and spigot components to have relative displacement. Axial stress generated at spigot is passed on
429
500
112.5
8.1
42
6.5
450
480
540
115
8.6
40
6.9
500
532
604
117.5
38
7.5
600
635
713
122.5
9.9
36
8.7
700
738
824
10.8
34
8.8
800
842
943
11.7
32
9.6
900
945
1052
12.6
31
10.6
1000
1048
1158
157.5
13.5
30
11.6
1200
1255
1377
167.5
15.3
1400
1462
1610
245
17.1
1600
1668
1820
275
1800
1875
2050
285
2000
2082
2266
290
2200
2288
2482
317
24.3
2400
2495
2702
336.5
26.1
2600
2702
2921
353
27.9
105.5
147.5
6000
3.5
18.9
1.8
6000/8150
20.7
22.5
28
27
26
25
30
17.7
to the socket through welded bead, locking ring, gland and connecting bolts, enabling the transmission of
axial stress to equip the joint with good anti-slippage performance. When the friction between the restrained
pipeline and its surrounding soil is greater than the axial stress generated inside the pipe, safe operation of
the pipeline can be guaranteed, thus avoiding the set-up of concrete block.
Application Field
In the following conditions, certain length of pipeline with TF-joints could be applied in order to prevent
pipeline slippage:
1. Places such as bends, tees, reducers and plugs, etc;
13.6
15.7
that the joint has certain axial stretching and deflection capability.
2. When the pipeline laying slope exceeds 20% (laying overground) or 25% (laying underground);
25
3. When it is uneconomical (such as large-diameter high-pressure pipelines, etc.) or unable to set concrete
19.7
21.8
A. The construction site is too narrow; there is no space to set up specified concrete block;
23.8
25.8
Installation method
27.9
12
XINXING PIPES
13
The technical parameters of TF self-anchored joint ductile iron pipe are shown Figure 7 and Table 7.
DE
enom
Front Stopper
Rear Stopper
Rubber Supporter
Rubber Gasket
Lu
Joint structure
K9
Xanchor self-anchored joint, as shown in Figure8, adopts the sealing structure of XT2 joint. Its socket is
DE
DGland
(mm)
(mm)
80
98
243
85
is where the sealing ring is set, and the stopper chamber is used to house the self-anchored components
100
118
264
88
which are comprised of the front blocks, the rear blocks, the supporting ring and welded bead.
150
170
321
94
200
222
375
100
250
274
433
105
300
326
509
350
378
567
400
429
591.6
450
480
675
500
532
700
600
635
811
700
738
935
800
842
900
DN
P(mm)
()
Lu(mm)
enom(mm)
6.3
PFA1(bar)
30
essential mechnism is to effectively prevent slippage through the two rows of rigid blocks . Meanwhile,
7.2
the circular sliding of the front and rear rows of blocks along the stopper chamber provides the joint with
7.7
6000
greater flexibility. Compared with other self-anchored joint, Xanchor joint features simpler structure, easier
8.1
1.5
8.6
120
Working principle
Working principle of Xanchor joint is quite different from that of the traditional self-anchored joint. The
6.8
110
designed to have two annular chambers, i.e. sealed chamber and anchoring chanber. The sealed chamber
25
Application Field
9.9
The same with TF joint, please refer to "1.4.1 Joint description Application Field ";
150
10.8
Installation method
1048
160
11.7
945
1158
175
1000
1048
1308
185
1100
1152
1420
200
1200
1255
1539
215
6000/8150
12.6
23
13.5
22
14.4
21
15.3
20
1 By adjusting the wall thickness class of the pipe and material of connecting bolts, etc., TF joint's PFA can reach 25bar.
Please consult us for detailed technical parameters.
14
XINXING PIPES
15
The technical parameters of Xanchor self-anchored joint ductile iron pipe are shown in Figure 9 and Table 8:
DE
enom
Lu
Figure 9 Xanchor self-anchored joint ductile iron pipe
Sealing principle
K9
DN
DE(mm)
D(mm)
P(mm)
()
1400
1462
1610
330
1500
1565
1710
341
1600
1668
1820
363
1.1
1800
1875
2050
410
2000
2082
2266
430
Lu(mm)
Structure of Flange-joint is shown in Figure 10. Its sealing is realized through the flanges compressing the
enom(mm)
PFA1(bar)
1.2
17.1
19
1.1
18
18
18.9
17
Flange joint is rigid joint with sound sealing performance. It is usually used in the following places, such as
1.0
20.7
16
0.8
22.5
15
8000
the connection with pumps, valves, fire hydrant as well as crossing foundation, walls and so on.
1 By adjusting the wall thickness class, Xanchor joints allowable operating pressure can reach PN25.
16
XINXING PIPES
17
Symbol
Name
Symbol
Pipe structure
XTJ jacking pipe, as shown in Figure 11, is to make a tubular reinforced concrete protective jacket on the
external wall of T-type joint pipe. Theres a jacking flange welded on the spigot of the pipe. During the pipe
jacking, the pushing force is evenly passed from the flange with ribbed plate welded at the spigot to the
socket, thus ensuring the pushing operation will not cause deformation of the spigot and will not damage the
outer protective sleeve;
Application Field
XTJ jacking pipes are applied when the pipeline need to cross obstructions such as roads, railways, rivers
and buildings, while trench excavation is not allowed or difficult to prepare on the construction site.
XTJ jacking pipe adopts T-type flexible joint. It features sound sealing performance, faster installation,
PN10/PN16/PN25
DN1400~DN1600
PN10/PN16
DN1800~DN2000
PN10
more reliable internal and external anti-corrosion coating, and is adaptive to various soil environments and
different transmitted media.
Flange
Concrete Cement
Stiffened Plate
Spigot
Rubber Gasket
Socket
18
XINXING PIPES
19
DE
topographical map, based on which initial analysis shall be formed on the corrosivity of the soil. Then,
250
DE(mm)
D(mm)
A(mm)
274
342
95
300
326
397
100
350
378
448
100
400
429
502
100
450
480
551
110
500
532
616
110
600
635
725
110
700
738
850
150
K9
800
842
956
150
900
945
1064
165
1000
1048
1170
175
1200
1255
1396
205
1400
1462
1630
229
1600
1668
1840
252
1800
1875
2060
290
2000
2082
2280
330
Lu(mm)
Total
weight
(kg)
4000
518
6000
773
4000
639
6000
953
4000
766
6000
1145
4000
907
6000
1353
4000
1045
6000
1554
4000
1268
6000
1890
4000
1626
6000
2423
4000
2281
6000
3385
4000
2661
6000
3992
4000
3171
6000
4706
4000
3684
6000
5376
4000
5027
6000
7436
4000
6841
6000
10151
4000
8310
6000
12380
4000
10110
6000
14895
4000
12046
6000
17740
through on-site examination, further analysis shall be made. Finally, through lab-test of the sample soil,
XINXING PIPES
KN
Tonf
920
94
1240
127
1270
129
1350
138
1560
159
1910
195
Collect potential corrosive elements for the embedded ductile iron pipes along the pipeline, including
2720
278
corrosive sewage discharged from livestock farms, wineries, paper mills and other factories, or from local
2720
277
3300
337
4140
422
5080
518
7240
739
9020
920
12360
1261
12360
1261
16970
1731
Data collection
Collect the topographical information for the area of pipeline burrial, such as the distribution and
altitudes of level ground, hills, swamp lands, paddy fields, rivers and beaches, soil types of various regions,
transitional areas of two different soils and the terrains with great changes. For example, in the dry area in
high altitude, the soil tends to be less aggressive; while in damp areas in low altitude such as ponds, lakes,
marshes and peat beds, the soil tends to be more aggressive due to rich humic acid and anaerobes. In the
river mouths, lowland, marshes, saline and alkaline lands and other regions along the sea, the aggressivity
of soil is probably high.
residence.
Note: 1. The jacking pipe with grouting hole can be provided according to customer requirements;
2. We could also supply jacking pipe with other wall thickness class. Please contact us for detailed technical parameters.
20
and backfilled soil, and soil polarity caused by local topographical and backfilling. Therefore, technicians
should familiarize themselves with the topographical and geography of the targeted area through
Size
DN
Pipelines buried underground will be exposed to various corrosive elements, including the aggressive soil
Collect potential disturbing power sources near the pipelines that probably corrode ductile iron pipes,
such as power plants, substations, HV transmission lines, and other forms of DC and AC interfering power
sources.
Gather local meteorological data, including maximum and minimum temperature, average temperature
per year, soil temperature at the burial depth of ductile iron pipes, soil freezing depth, underground water
level, rainfall volume and sunlight intensity, etc.
A report shall be issued with information mentioned above for the reference of designers.
Site surveys
The selection of site surveys shall be based on following principles:
a. At least 2 test points shall be chosen for every soil type;
b. For the same type of soil, one test point shall be chosen every 400~500m;
c. Test points shall be typical for the topographical features of the area along the pipeline;
d. Mark test points on the general pipeline layout plan to make a soil survey test point distribution plan.
Xinxing Ductile Iron Pipes Technical Manual
21
Product description
Soil resistivity test: soil resistivity, as an important index of evaluating soil aggressivity, is a
Zinc coating used as external protection has proved to be one of the most effective anti-corrosion solutions
comprehensive factor of soil water content and salt content, and reflects soil conductivity. In general, the
throughout the world. It can prolong the service life of pipelines. Standard anti-corrosion coating provided
smaller the soil resistivity is, the stronger the soil aggressivity is. AC quadrupole test method is adopted on
by Xinxing is metallic zinc coating applied by electric arc (C-Class pipe 200g/m2, K-Class pipe 130g/m2). A
the site.
HCPE finishing layer of at least 70um thickness will be sprayed outside the zinc coating. Structure of such
ORP test (Eh7): oxidation reduction potential is an index that can reflect comprehensively oxidation
coating solution is shown in Figure 13. The finishing layer is in porous structure, as shown in Figure 14.
reduction degree, which has a lot to do with the activity of bacteria in the soil. To certain extent, the lower
finishing layer
Eh7 is, the greater corrosive action of sulphate reducing bacteria on metals is. Therefore, oxidation
metallic zinc
cast iron pipe
reduction potential can become an index of soil microbiological corrosion under the condition of strong
reducibility.
Laboratory analysis
Laboratory analysis is supplementary to the analysis mentioned above. Chemical analysis conducted in the
laboratory mainly includes the following items:
PH value, total soluble salt, moisture content, soil bulk density, air content, Cl-, SO42-, S2-, microorganisms,
etc.
Anti-corrosion mechanism
Zinc coating is the basic external coating solution provided by Xinxing. It features satisfactory anti-corrosion
performance in most of the soil environments. However, in strong corrosive soil where zinc coating
Stable protective layer: Zinc will corrode gradually to generate insoluble zinc salt in the process of
would not be enough, PE sleeve will be used as additional anti-corrosive coating; or special coatings and
contacting with environmental soil, which will tightly adhere to the pipe walls so as to form a layer of
other strong anti-corrosion methods shall be taken to protect the pipelines. Xinxing can help customers
design cost-effective external anti-corrosion solutions for pipelines that can fulfill requirements of the soil
environment. Table 11 is a proposed anti-corrosion coating solution based on different corrosion levels of
Pore-sealer
the soil.
zinc
Pipelines
corrosive
highly corrosive
The porous finishing layer sprayed on zinc coating also plays an important role. It is good for cathodic
protection and self-healing, and also for converted products of zinc to generate stable and tight insoluble
protective film.
22
XINXING PIPES
23
Self-healing of damaged zinc coating: Some pipes may be locally damaged probably during
epoxy coating
Zn-Al rare earth alloy
transportation or installation. Zinc will transform into zinc ion rapidly under the action of primary cells. Zinc
ion can migrate through pores of finishing layer and cover the damaged portions, generating stable and
insoluble protective layer, as shown in Figure 15.
zinc corrosion products
current
Zn++ ions
Anti-corrosion mechanism
In short, zinc coating plays an important role of anti-corrosion: on one hand, it will generate tight insoluble
protective film which will adhere to pipe walls, thereby reducing electrochemical corrosion to great extent;
Active anti-corrosion: Just like pure zinc, Zn-Al rare earth alloy is also a kind of active anti-corrosion
coating.
on the other hand, the anti-corrosion performance of zinc coating and finishing layer also is reflected on
Stable protective layer: Being similar with zinc coating, a layer of continuous, impermeable and insoluble
their mutual action. There is excellent adhesiveness between zinc and cast iron & zinc and finishing layer,
protective film that is hardly penetrated forms on ductile iron pipe walls. Aluminum in the alloy features
forming a complete protective screen between pipe and the external environment, and preventing anti-
inactivation, and it can reduce the consumption rate of zinc even in the soil with high corrosivity; the addition
corrosion failure.
of a small amount of rare earth element (Re) can purify the coating structure to reduce active points of the
Application field
surface during the coating corrosion; it can also refine the crystal grains and reduce porosity of the coating
This kind of coating is applicable to most of the soil environments with slight aggressivity.
so as to compact the coating structures, thereby reducing the corrosion passages, as shown in Figure 17.
Executive standards:
ISO 2531, ISO 8179, GB /T 13295, GB/T 17456, BS EN 545
blue epoxy
Figure 17 Porous Structure of the coating solution of Zn-Al rare earth alloy + blue epoxy coating
thickness) is sprayed on the alloy coating so as to form active anti-corrosion coating. Coating structure is
shown in Figure 16.
24
XINXING PIPES
25
Zn-Al rare earth alloy coating features self-healing effect just like coating zinc.
PU coating of ductile iron pipe and fitting is formed by the PU material sprayed and cured on the surface
Due to the addition of rare earth, Zn-Al rare earth alloy coating features the following advantages compared
of pipe/fitting that is bi-component, solvent-free and 100% solid. This kind of coating has excellent anti-
corrosion performance, high impact resistance and wearing resistance, which is applicable to the soil with
very strong aggressivity and all other types of the soil.
Reinforcement effect
With strong chemical activity, rare earth element can react with many elements in Zn-Al alloy to generate
intermetallic compounds with strong hardness. Distributed in crystal boundary in a mesh pattern, these
compounds can hinder creep slip, thereby improving the hardness and wear-resistant property of alloy
epoxy coating
PU coating
ductile iron pipe wall
Refining effect
During solidification of the coating, rare-earth element can reduce the surface tension of plating solution
to increase the crystal core so as to refine the crystalline grains. Such fine eutectic structures can prevent
the extension of cracks, even the structures and eliminate bare spots on the surface of coating. This is
the important mechanism of rare earth to improve the plasticity and flexibility of the coating, and it is also a
special feature of the rare-earth alloy coating.
Anti-corrosion performance
Re element can refine microstructure of the coating and reduce its porosity. Meanwhile, it can strengthen
Zn-Al alloy coating. Therefore, addition of a small amount of Re element can further improve the anticorrosion performance of Zn-Al alloy coating.
Application fields
Zn-Al rare earth alloy coating is an enhanced anti-corrosion solution. It is applicable to the soil with strong
aggressivity (i.e. soil with low resistivity, soil influenced by underground water or mixed soil), where PE
sleeve is not needed, except the following situations:
Acid peat soil;
Soil containing garbage, oxide skin and slag, or soil polluted by waste water and industrial effluent;
Soil below the sea level and with resistivity less than 500cm.
When applied to the soil types listed above, including the one with stray current, other type of external
coatings (such as PU coating) will be recommended.
XINXING PIPES
Adopted material
Average thickness m
Minimum thickness m
pipe body
PU coating
900
700
epoxy coating
250
200
Location
Specification range
Executive standards:
26
27
Additional protection
For the soil with very strong aggressivity, proper additional protection shall be made for the joints during
installation of pipelines, e.g. application of external heating shrink sleeve.
Tested items
Water resistance
Requirement
Less than 15% weight increase after immersion in 50 deionzed water
Less than 2% weight loss after drying
1
Chemical resistance
Less than 10% weight increase after immersion in 10% H2SO4 for 100 days
The weight change 4% after drying.
Impact strength
Indentation hardness
Elongation at break
2.5%
10 m
0.8
Non-porosity
When tested with 4.2kV voltage,the PU coating shall be free from porosity.
Hardness
Shore D > 70
Adhesion
advantages of PU coating
With strong mechanical strength, rock impact resistance and soil stress resistance, it can hardly be
damaged during handling and installation.
Due to good water resistance and zero anti-permeability coefficient, the coating wont suffer from shellfish
erosion when applied in the marine environment for a long time.
Due to its good performance in chemical resistance and electric corrosion resistance, ductile iron pipes
with PU coating can be applied to complicated soil environment, with prolonged life span.
Application fields
Pipes and fittings with PU coating can be applied to the soil environment with very strong aggressivity and
all other types of soil listed below:
Humid regions such as harbor and marshes;
Hydrous area that is salty and alkaline etc.
Executive standards:
ISO 2531, GB /T 13295, GB/T 24596, BS EN545 and BS EN15189
28
XINXING PIPES
29
Test results
Test standard
200
ISO 8180
material density/kg/m
910~935
ISO 1183-1
impact resistance/g
900
tensile strength/MPa
20
elongation/%
500
20
ISO 6383-2
thickness/m
3
Specification range
This kind of anti-corrosion coating is applicable to ductile iron pipes of all sizes.
Anti-corrosion mechanism
The anti-corrosion mechanisms for PE sleeve (film) wrapped outside zinc coating are as following:
First of all, PE sleeve can separate the pipelines from corrosive soil and inhibit the generation of
electrochemical cell. At the same time, it can also isolate stray current.
The PE sleeve is a kind of anti-corrosion method whose performance is achieved through the changing
of corrosive environment: it can change the corrosive environment from non-homogeneous soil with strong
aggressivity into one that is homogeneous with weak aggressivity.
Application fields
It is suggested to adopt this kind of protective layer for corrosive soil, for example:
Soil with low resistivity (with indicator of high aggressivity);
Regions with stray current;
Regions with high chlorine or sulphur content or active bacteria indicated by the analysis.
Executive standards:
ISO 2531, ISO 8180 and GB /T 13295
30
XINXING PIPES
31
Usually, various types of water are available to be supplied. Sometimes, it is water with low mineral content
The internal lining of ductile iron pipes must be equipped with excellent hydraulic and anti-corrosion
Xinxing can provide ductile iron pipes with various internal linings, which are applicable for the conduction
performance. Factors such as corrosivity, flow speed and environment temperature of the conveyed fluid
of various types of water; based on the features of delivered water, proper lining materials (such as cement
have to be taken into consideration while choosing the pipe lining. Surface smoothness is also one of the
mortar lining, cement mortar lining with epoxy seal coats, PU lining, or ceramic epoxy lining) shall be chosen
(e.g. soft water), which may attack the materials just like corrosive or aggressive water.
Adopted for the delivery of potable water, the anti-corrosion lining of ductile iron pipes should be nontoxic.
This is the most basic requirement for the choice of lining.
While adopted for sewerage delivery, the anti-corrosion performance that features microorganism resistance
and liquid erosion resistance becomes very important for the lining. And it is those linings with high abrasion
resistance and strong acid resistance (especially sulfuric acid resistance) that can provide long-term,
reliable protection for the pipes.
Application Area
Solvent-free PU
seal coats
Epoxy coating
Rubber gasket
Corrosive water
Corrosive water refers to water that corrodes the metal of pipe without lining. Oxygen contained in most of
the water can react chemically with iron, which causes its oxidization, generating nodules and tuberculation
on internal pipe wall. It will reduce the pipe cross section and significantly cause water head loss increasing
over time. This phenomenon often happens in the old pipe without cement mortar lining.
Standard lining: Applicable for most raw water and portable water;
Reinforced anti-corrosion lining: Applicable for water which can attack ordinary cement (soft water,
slightly acidic water or highly abrosive water);
Special lining: Applicable for very special cases or corrosive water (e.g. industrial discharged water)
Xinxing will recommend proper internal linings based on water composition analysis. Table 16 summarizes
Aggressive water
Aggressive water is the water that corrodes calcareous materials (such as cement). Based on chemical
analysis, three results will be caused by the changes in mineral content, PH value and temperature of the
water:
Under the given temperature, the water with calcium-carbon balance will neither cause attack nor calciumcarbon deposition.
Scale deposition water tends to generate calcium salt deposition (e.g. calcium carbonate) on the internal
surface of pipe.
Aggressive water can attack the cement mortar containing calcium (e.g. lime, calcium carbonate, or
aluminum silicate, etc.)
According to the relevant international standards, potable water can be neither corrosive nor aggressive.
32
XINXING PIPES
Lining material
Standard lining
Enhanced lining
Special lining
33
Product description
With the proceeding hydration reaction of cement, the cement mortar lining will shrink gradually. Therefore,
Cement mortar lining of ductile iron pipes is applied through centrifugal application method:
it is inevitable to form radial displacement and small cracks. This is a unique feature of cement mortar, which
When pipes are rotating on the lining machine, certain amount of cement mortar is poured into the pipes.
is allowable by the standard. Thus, no unfavorable influence on the mechanical stability of the lining will be
Through high-speed revolution with acceleration about 30G under the centrifugal force, such cement mortar
brought by such cracks and radial displacement, as well as other cracks caused during manufacturing or
will fully cling to the internal surface of pipe, forming a dense and smooth lining with uniform thickness,
transportation.
which can provide good mechanical properties after curing for certain amount of time. Thickness of cement
When the pipe with cement mortar lining contact water, these cracks and radial displacement will be closed
and healed along with expansion of the linings and continuous hydration of cement; therefore, the anticorrosion effect wont be influenced.
Good mechanical property
Lining thickness
Nominal thickness (mm)
Minimum thickness at one point(mm)
Expansion coefficient
The linear thermal expansion coefficient of cement mortar lining is 12 x 10-6/ , which is almost equal to
80300
that of ductile iron (11 x 10-6/ ). Therefore, it can reduce the risk of crack generation due to difference of
350600
7001200
3.5
14002000
22002600
12
With excellent abrasion resistance, cement mortar lining can be used to convey raw water with highly
abrasive particles
mortar linings, which contributes to the linings smoothness. According to the test of Testing Center of
China Institute of Water Resources and Hydropower Research, the equivalent roughness K of such lining is
1.8
1.0
as the tolerance, it is suggested that the value of K selected as 0.10mm for the design purpose.
0
-0.2
Application fields
Fe+3
0.6
Table 19 shows the substances that can be conveyed by various cement mortar linings.
Fe++
a
(cor
Ductile iron pipe with common silicate cement mortar lining is applicable for water-supply project;
Fe2O3
rosio
Ductile iron pipe with sulphur resistant cement mortar lining is applicable for water supply project and
(passivation)
n)
-0.6
Fe3 O
Ductile iron pipes with high-alumina cement mortar lining are applicable for the conduction of sewages
Fe
0.030mm. Taking into consideration of the roughness caused by fittings, valves and other devices, as well
FeO4
b
potential V(S.H.E)
Anti-corrosion mechanism
and industrial wastewater containing certain chemical substances. Nitrile butadiene rubber (NBR) gasket
HFeO2
(immunity)
-1.4
-2
0 1
11
13
15
resistance.
34
XINXING PIPES
35
Water properties
PH Value
5.5
15
unlimited
As shown in Figure 20, cement mortar lining with epoxy seal coats is formed by the curing of water borned
2-
400
3000
unlimited
epoxy spayed on the surface of cement mortar lining. Generally, the thickness of epoxy seal coats around
2+
100
500
unlimited
70um except for special requirements. With excellent anti-corrosion performance, this kind of lining can
30
30
unlimited
SO4 (mg/l)
Mg (mg/l)
+
NH4 (mg/l)
Executive standards:
ISO 2531, ISO 7186, ISO4179, GB /T 13295, GB /T 26081, GB /T 17457, BS EN 545 and BS EN598
Lining structure
finish coating
zinc
ductile iron pipe wall
cement mortar lining
epoxy seal coats
36
XINXING PIPES
37
Material of seal coats: pass WRCNSF sanitary test of BS6920 and WRAS certification.
Specification range
With combined performance of active and passive anti-corrosion, in case epoxy seal coats is damaged or
Certification
some voids exist in the seal coats, cement mortar lining can provide active anti-corrosion protection, thus
In compliance with requirements of ISO16132:2004, it can prevent PH value from increasing in the initial
period of water introduction and prolong service life of the lining, thus guarantee water quality. We have
With excellent alkali resistance, it can withstand the alkaline environment of cement mortar linings in long
run; with excellent acid resistance, it can withstand the erosion of delivered water (e.g. weak acidic water).
Inhibit precipitation of alkaline substances
After 3-months closed cyclic test conducted under conditions of 6 bar pressure and 2m/s flow velocity, the
PH of the test water is far less than 9.5 as required by ISO 16132 (Figure 24 below shows testing procedure
and testing apparatus ).
Anti-corrosion mechanism for cement mortar lining with epoxy seal coats
Structure of cement mortar lining with epoxy seal coats is shown in Figure 23. Ductile iron pipes with cement
The result of short-term sealing performance test is around 8.2, which is far less than the requirement of
mortar lining plus epoxy seal coats combine active anti-corrosion with passive anti-corrosion. On one
hand, epoxy seal coats provides a physical barrier for internal wall of ductile iron pipe, which can reduce
water contacting with or isolate water from the internal wall of ductile iron pipe, namely passive corrosion
resistance;on the other hand, this kind of lining can also slow down or stop releasing alkaline substances
from the cement mortar into water, so it can ensure alkaline substancess enrich on internal wall of ductile
iron pipe, and thereby provide chemical protection by means of passivation, namely active corrosion
resistance. In this way, long-term corrosion resistance can be provided for this lining.
10
11
12
1
9
3
13
2
epoxy seal coats
cement lining
14
Stop or slow down releasing alkaline substances from the cement mortar
Ca(OH)2
Ca(OH)2
Ca(OH)2
Ca(OH)2
Ca(OH)2
The epoxy seal coats doesnt contain any organic solvent, thus wont pollute the environment or cause harm
to constructors;
The seal coats is non-toxic after curing, neither polluting water nor producing substances harmful to peoples
health.
It has passed British WRAS sanitary property test of BS6920
The water-bored epoxy coating is compatible with drinking water and has passed WRC-NSF Sanitary test of
BS 6920 and WRAS certification.
38
XINXING PIPES
39
Lining structure
Cement mortar lining with epoxy seal coats is smoother than cement mortar lining, which can reduce the
metallic zinc
friction resistance. Xinxing has entrusted an authorized testing organization to test roughness coefficient
of ductile iron pipes with cement mortar lining epoxy seal coats, and the result shows that its roughness
Epoxy coating
Lining thickness
The thickness of PU lining varies with water quality and pipe diameter. The thickness of the linings are
shown in Table 19 and Table 20:
Table 19 Lining Thickness of Pipes and Fittings Applied to Portable Water Delivery as Required in ISO2531
Socket and spigot
(contacting with water)
Pipe body
DN
Average thickness
m
80~200
1300
200
1500
Minimum
thickness
m
Average
thickness
m
Minimum
thickness
m
800
300m
250m
pipe/fitting bodies that is bi-component, solvent-free system. This kind of lining has excellent anti-corrosion
performance and wearing resistance, as well as high impact resistance specific to various transmission
Table 20 Lining Thickness of Pipes and Fittings Applied to Sewage Water Delivery as Required in ISO7186
mediums (such as portable water, wastewater, softened water, municipal sewage, and industrial
wastewater), which is applicable to all water supply projects and municipal sewage drainage projects from
soft water to hard water.
40
XINXING PIPES
DN
Pipe body
Average thickness
m
Minimum
thickness
m
80~200
1300
800
250~700
1500
800
700~1000
1800
1000
1000
2000
1000
Average
thickness
m
Minimum
thickness
m
Minimum thickness m
300m
250m
150um
41
Stability of PU lining
PU lining of ductile iron pipe produced by Xinxing can provide excellent chemical stability and ageing
Certification.
resistance: the increased weight of coating wont exceed 4% after its immersion in 50 distilled water for
Epoxy coating: complying with EN 14901, passing WRC-NSF test of BS6920 and obtaining WRAS
180 days; the adhesion of PU lining is greater than 8Mpa after it is exposed outdoor for 6 months.
Certificate.
Good flexibility
PU lining also has good flexibility, which can withstand the impact and deformation from transportation,
Specification range
With smooth surface, it features small friction and excellent hydraulic performance. Xinxing has
Certification
PU linings of ductile iron pipes produced by Xinxing comply with requirements of GB/T 24596 and BS EN
entrusted authorized testing organization to test roughness coefficient of K of ductile iron pipes with PU
linings, and the test result is 0.010mm. Considering roughness arising from fittings, valves and other
devices, as well as tolerance, it is suggested that K value shall be 0.050mm for the design purpose.
Tested items
water resistance
1
Chemical resistance
Ovality resistance
Ovality of pipe
2% ~ 4%
3% ~6%
4%~ 8%
The coating shall be free from damage.
Elongation at break
2.5%
Resistance of coating in
0.1M NaCl solution
108m2
0.8
Non-porosity
42
Technical requirements
XINXING PIPES
Hardness
Shore D > 70
10
Adhesion
At 20 , adhesion 11 MPa
11
Abrasion resistance
The wearing depth of the lining 0.2mm after 100000 movements (50000 cycles)
43
Lining thickness
In order to ensure overall corrosion resistance of the pipe lining, the thickness of ceramic epoxy lining and
Ductile iron pipes with PU linings can be used to deliver water as follows:
coating of socket and spigot shall comply with requirements in the table 23:
all types of portable water, sewage water with PH 1~13 and industrial water shown in Table 22:
Transmitted mediums
PH of transmitted mediums
Portable water
1~13
Sewage water
1~13
Industrial water
13
Minimum thickness m
Minimum thickness m
Minimum thickness m
1000
250 m
150um
Routine test
Adhesion test: Ceramic epoxy lining possesses excellent adhesion. Xinxings requirement on adhesion
Non-porosity: Each ductile iron pipe with ceramic epoxy lining shall be subject to holiday test under
Applicable standards for ductile iron pipe and fitting: ISO 2531, ISO 7186, GB /T 13295, GB /T 26081, BS
EN 545 and BS EN598
Applicable standards for PU lining of ductile iron pipe: GB/T 24596 and BS EN 15655
Specification range
Xinxing can provide DN100~DN2200 full range of products
metallic zinc
cast iron pipe
ceramic epoxy lining
Epoxy coating
The coating surface is smooth as the mirror with small friction and excellent hydraulic performance. It
The coating is solvent-free, without volatile solvent released during usage, so it complies with safety
Table 25 shows the properties of ductile iron pipe with ceramic epoxy lining produced by Xinxing:
projects.
Lining structure
44
XINXING PIPES
45
Performance requirement
Testing method
0.075mm
ISO 7186
Impact resistance
ISO 6272-1
0.00
ISO 7253
ISO 4628
Chemical
resistance
25% NaOH(60 )
20% H2SO4
1.10.1 Repairment of Zinc coating + HCPE finishing layer/Zn-Al rare earth alloy + epoxy
coating
Repairment ofsuch coatings consists of two steps:
Step 1: Repairment zinc coating/Zn-Al rare earth alloy coating
Step 2: Repair blue epoxy coating or HCPE finishing layer
Adhesion
10Mpa
ISO 4624
Coating thickness
1000um
ISO 2808
Non-porosity
3KV
NACE PR0188
Equipment required
brush
paint brushes
roller
gas torch
Repairing paint:
Zinc-rich primer:10kg
Procedure
Brush to remove dirt
46
XINXING PIPES
47
Equipment required
brush
paint brushes
roller
gas torch
Repairing materials:
Blue epoxy paint - used to repair Zn-Al rare earth alloy + epoxy coating
HCPE anticorrosion paint - used to repair zinc coating + HCPE finishing layer
Equipment required
wire brush
paint brushes
spatula
chisel
rotary wire brush
gas torch
Repairing materials
SPUA-R300 solvent-free PU paint
Procedures
Remove the damaged coating and its surrounding coat
with poor adherence by knife or other tools and remain
the coat with sound adhesion and no defect. Clean the
surface of ductile iron with a motor wire brush or other
tool until its surface reaches St3. Brush away debris and
dust to keep the repair-to-be surface clean.
Procedures
Brush to remove dirt
48
XINXING PIPES
49
Equipment required
wire brush
paint brushes
Trowel
spatula
chiselhammer
palette knife
repair products
Procedures
Turn the area to be repaired to face upwards.
Remove the damaged area and surrounding hollow lining with
a hammer or driver
The edges shall be vertical to the ductile iron pipe wall and
ductile iron surface shall be exposed
A
Remove any loose debris with a wire brush
Clean the surface to be repaired thoroughly, including part of
the rusted substrate.
Wet the area to be repaired
Wet cement mortar lining around the area to be repaired a few
minutes before the repairing work
B
20kg
4kg
Proportion
Weight ratio A:B = 5:1
Stir component A before mixing. Weigh five portions of component A and one
portion of component B prior to use as required. Place them into a container.
Stir them at least 3 - 4 minutes with a blender or stirrer driven by low-speed
electric drill, until they are mixed evenly.
The ready mixture shall be used up under 25 within 2h. Otherwise, it shall
be discarded.
Procedure
Brush to remove dirt
Weight Ratio
100
200
35~40
Firstly mix two kinds of powder materials, and then add certain
amount of water, mixing to obtain the continuous slurry.
If necessary, add small amount of water according to the
viscosity.
Brush the ready paint on the surface to be repaired with thickness of gray
epoxy seal coats of 70 um. The coating appearance shall be smooth without
bubble, void or other defect.
Fill the defective parts with new mortar, smear the mortar
on it to a uniform thickness with a trowel and make it dense.
Operate evenly to obtain flat and smooth surface. If required,
regularly water the trowel to facilitate troweling
50
XINXING PIPES
51
Procedure
Remove the damaged coating and its surrounding coat with poor adherence
with knife or other tools and remain the coat with sound adhesion and no
defect.
Clean the substrate of ductile iron base with a motor wire brush or other tool
until its surface reaches St3.
Brush away debris and dust to keep the repair-to-be surface clean.
The temperature of the surface to be repaired shall be 5 above the dew point
at least. In case that the surface is wet or the ambient temperature is very low,
the surface can be heated by gas torch so as to keep it dry and at least 5
above the dew point.
52
XINXING PIPES
53
Chapter II
Manufacturing
Process and
Quality Control
System
54
XINXING PIPES
55
Chapter II
Manufacturing
Process and
Quality Control
System
58
62
56
XINXING PIPES
57
Composition adjustment
in the electric furnace
Spheroidizing
is added into the sand core mold, tamped and solidified for the
Centrifugal casting
centrifugal casting.
Sand cores
Polishing
Zinc coating
Annealing
Weighing
qualified high-temperature molten iron flows through a launder into the metal mold rotating at high speed,
and then is distributed on the internal surface of metal mold under the centrifugal force, finally it is solidified
into a pipe. The impurities and gas in molten iron is sufficiently excluded due to the centrifugal force. The
gradual inward solidification makes the pipe wall extremely dense, so as to save materials to the most and
Spray of external
finishing layer
Packing storage
2.1.2.3 Annealing
Annealing treatment is a necessary and important procedure during production of ductile iron pipe.
Generally, the elongation of ductile iron pipe by centrifugal casting is 2~5%, inferior to the requirement
specified by ISO 2531. In order to enhance elongation, the cast pipe shall be annealed, that is, the pipe
is heated to certain temperature in the annealing furnace, and then cooled to below certain temperature
along with the proper annealing curve, and continuously cooled in ambient temperature. After the annealing
Spheroidization of molten iron
treatment, the mechanical properties of ductile iron pipe can reach the indexes in the Table 1 and comply
with ISO 2531:
XINXING PIPES
Component analysis
Xinxing Ductile Iron Pipes Technical Manual
59
Minimum elongation A /%
DN80~2000
DN80~1000
DN1100~2000
420
10
420
Note: 1. The yield strength (RP 0.2) can be measured by agreement between the supplier and purchaser. Where:
RP 0.2 270MPa, when A 12% for DN80 ~ 1000; or RP 0.2 270MPa, whenA 10% for DN 1000 and above.
RP 0.2 300MPa under other conditions.
2. For centrifugal ductile iron pipes between DN 80 ~ 1000,when the wall thickness class is above K12, minimum elongation is 7%.
with ISO 2531, qualified result of which is the prerequisite for the products entering into the next procedure .
After the spraying of finishing coating and marking, the cured pipe (DN 300) will be packed and put in
storage, and then shipped to the designated location as scheduled.
Zinc coating
60
XINXING PIPES
61
Qualified
SQA
Composition
composition
Molten iron temperature&
composition adjustment
Disqualified
pipe mold
maitenance
Ferrosilicon,
magnesium
Molten iron
SQA
Composition
Particle size
Composition
Temperature
Spheroidisation
Sand, resin
Core preparation
Composition
Temperature
Dimensions
Appearance
Centrifugal casting
Disqualified
Appearance
Pipe weight
Pipe heat treatment
Disqualified
Appearance
Dimensions
SQA
Composition
Particle size
Dimensions
Appearance
Strength
Disqualified
Reject
Hardness performance
Reject
Zinc spray
structure
Sand, cement
Thickness
Finishing
Disqualified
Appearance
Dimensions
Preparation of
cement mortar
inspection
Weight
SQA
Particle size
Leak tightness
Lining thickness
Legend
Start, end
Operating
Appearance
Product inspection
Process control
Appearance
Spray finishing layer
Thickness
Marks spray
Disqualified
Packaging
Appearance
SQA
Inspection
Package
Completion,
storage
62
XINXING PIPES
63
QC Item
Testing Frequency
Inspection Equipment
Each furnace
Spectrometer
Return
Each furnace
Spectrometer
Readjust
Each furnace
Thermometer
Readjust
Composition of nodulized
molten iron
Each pack
Spectrometer
Return
Core appearance
Full testing
Visual inspection
Repair or destroy
Core dimensions
5 pcs/shift/specification
Caliper
Destroy
Each piece
Rework
Casting temperature
Thermometer
Adjustment or return
Appearance
Each piece
Visual inspection
Adjustment
10
Pipe weight
Each piece
Platform scale
Adjustment
11
Furnace temperature
Thermal instrumentation
Adjustment
12
Chain speed
Inverter
Adjustment
13
Appearance
Each piece
Visual inspection
Reject
14
Mechanical property
1 piece/batch
Reject
15
1 time/day
Electronic balance
Rework
16
Pipe weight
Full testing
Electronic scale
Reject
17
Dimensions
Full testing
Reject
18
Pressure Test
Full testing
Reject
19
Each bucket
Adjustment
20
Lining appearance
Each piece
Visual inspection
Reject or rework
21
Lining thickness
1 time/hour
Reject or rework
22
Curing time
Each furnace
Watch
Adjust
23
Curing temperature
Each furnace
Thermometer
24
Appearance
Full testing
Visual inspection
Reject or rework
25
Film thickness
3 pcs/shift/specification
Rework
26
Lining thickness
3 pcs/shift/specification
Reject or rework
Test requirements
Test conditions
1. Positive internal
hydrostatic pressure
2. Negative internal
pressure
Test duration: 2h
Maximum pressure variation during the
test: 0.09 Bar
3. Positive external
hydrostatic pressure
24,000 cycles
Test pressure: Between PMA and
(PMA-5) bars
No visible leakage
Test method
W
F
Figure 2 apparatus for positive/negative internal hydrostatic pressure and cyclic internal hydraulic pressure
W/2
W/2
W/2
64
XINXING PIPES
65
Chapter III.
Requirements
for Storage and
Transportation
of Ductile Iron
Pipe
66
XINXING PIPES
67
Chapter III.
Requirements
for Storage and
Transportation
of Ductile Iron
Pipe
68
XINXING PIPES
70
3.1.1 Precautions
3.1.2 Lifting tools
3.1.3 Lifting
3.2 Transportation
71
3.3 Storage
71
69
3.2 Transportation
3.1.1 Precautions
(1) If truck or train is adopted for transportation. The carriage must be cleaned without foreign matters. At
Ductile iron pipe shall be lifted by straps or special tools and handled with care. The pipes shall be matted
the same time, the loading scheme shall be prepared according to the acceptable capacity of vehicle;
steadily and firmly without collision with each other during shift-loading and transportation. The operation
(2) If truck or train is adopted for transportation, planks formed by two or more pieces of wood shall be
shall strictly follow the requirements of protection and fastening, so as to avoid damage to the pipe and
placed on the carriage floor so as to avoid the direct contact between the socket end and carriage floor; If
protective coating.
a flat bed trailer is used for transportation, the casting pipes shall be placed on planks and then fixed by
wedges; the length of pipe extending out of the vehicle shall not exceed 1/4 of the pipe length; if iron pipes
are loaded in more than one layer, the pipe spigot and socket end of each layer shall be staggered and
finally fixed with steel wire rope firmly; the soft protective materials shall be used to separate pipe and pipe,
pipe and rigid vehicle body, as well as pipe and fastening steel ropes;
(3) While unloading from the vehicle, it is necessary to avoid directly pulling or dropping the ductile iron pipe
,wrapped or not, over the ground, even over the sand ground,for dropping them.
3.3 Storage
3.3.1 Requirements for Stacking Site
3.1.3 Lifting
3.3.1.1 The selected site for ductile iron pipe storage shall be flat and solid, and the following places shall
3.1.3.1 For ductile iron pipes packed in bundles, strap and special lifting tools shall be used to lift them from
be unacceptable:
the bottom of whole bundle. It is prohibited to directly hook pipes or package strap so as to avoid packing
distortion, breakage of package straps or bundle-off during lifting. Generally, one hook is to lift one bundle.
- Swampy areas;
If it is necessary to lift several bundles by a hook, the special lifting gear shall be used to prevent packing
deformation, so as to avoid the package damage, such as steel belt breakage and bundle deformation;
3.3.1.2 Two tracks of wooden planks shall be placed under the pipes to avoid their direct contact with the
3.1.3.2 For ductile iron pipes packed in bulk, special hook or lifting strap can be used to lift one or several
3.3.1.3 For the long-term storage, the pipes shall be covered with canvas or woven cloth, so as to protect
3.1.3.3 When forklift is applied, all its areas contacting with the pipes must be protected during lifting;
70
XINXING PIPES
71
The socket and spigots ends of pipes of each layer are arranged alternately.
Taking into account the bearing capacity of the underlying pipes, the stacking height for K9 ductile iron pipe
is recommended as shown in Table 1, and the preferred height for C-Class ductile iron pipes is shown in
Size
Table 2.
Pyramid
Square
Pyramid
Square
DN80
16
16
DN700
DN100
16
16
DN800
DN125
16
16
DN900
DN150
12
12
DN1000
DN200
12
12
DN1100
DN250
12
DN1200
DN300
12
DN1400
DN350
12
DN1500
DN400
12
DN1600
DN450
12
DN500
DN600
Table 2 Stacking Mode for C-Class Ductile Iron Pipes With Preferred Pressure Class
Recommended stacking layers
DN
(m)
80
7(4)
100
6(4)
150
5(3)
200
5(2)
3.3
250
4(3)
3.6
300
4(2)
3.1
Pyramid
72
XINXING PIPES
350
14
4.0
400
12
4.0
450
10
4.0
500
3.5
600
3.7
700
3.5
800
3.4
900
3.9
1000
3.5
73
Chapter IV.
Engineering
Design of
Water Supply
& Drainage
Pipeline
74
XINXING PIPES
75
4.1 Determine the regional water demand and satisfy the requirements
for water pressure 78
4.1.1 Determination of water consumption
4 .1.2 Water delivery pressure
4.2 Selection of pipe diameters 79
Chapter IV.
Engineering
Design of
Water Supply
& Drainage
Pipeline
85
76
XINXING PIPES
77
Qh=
1000xKh xQd
24x3600
Kh xQd
86.4
l/s
The total water consumption of community is subject to the local water resources, economic development,
living habits, industrial and agricultural production scale and so on, and the check computation shall be
conducted by reference to the design standards for local living water consumption and relevant industries.
ELA-Hc-HtP
EL ALowest hydraulic elevation at
Water Source A
hydr
aulic
grad
ient
Jt
When taking into account the hourly variety coefficient Kh of water consumption, the maximum hourly water
(m3/d)
water-consuming point B
Ht total head loss of pipeline
Hc
Qd=(1.15~1.25)(Q1+Q2+Q3+Q4+ Q5)
ELA
Q=
D v
4
Formula to calculate pipe diameter can be obtained as below:
D=
4xQ
xv
as below:
78
XINXING PIPES
79
It is indicated from the above formula that: When water volume Q is determined, the smaller flow velocity v
characteristics throughout one year, which can serve as the basic data to calculate the annual electricity
will result in the larger pipe diameter D, and correspondingly increase the construction cost of pipe network;
however, it can reduce pipe head losses and the corresponding cost for pipe network management; and
vice versa.
Therefore, the following issues shall also be considered during selection of pipe:
Through calculating total cost of pipes with different diameters, the diameter of pipe with the lowest total
The first is construction cost of pipeline which covers the material cost of piping components, the equipment
cost, such as pressurized water pump unit, expenses for installation and construction, etc.
The second is pipeline operation & management costs, including power cost for pipelines opertion,
W=Cp+CmNPV+CeNPV
maintenance cost and interest on investments. In most projects, usually several comparative solutions are
designed, from which a most economical and practical solution will be selected.
Therefore, the optimization method is commonly used to obtain the best solution of velocity v or pipe
CmNPV NPV sum of pipeline maintenance cost of each year within calculation period
diameter D during the pipe network design, namely: in a certain period t (payback period of pipeline
($ 10,000)
project), the velocity with the minimum sum of the construction cost and management fees of pipe network
1)Pipeline investment Cp
In order to prevent the pipe network accidents against water hammer phenomenon, it is recommended that
Pipeline investment covers all costs related to the pipeline laying, including pipes fee, production cost,
the maximum design flow velocity of the ductile iron pipe shall not exceed 2.5 ~ 3.0m/s; for transmission
transportation costs, anti-corrosion costs for internal and external walls, construction cost and greening-
of turbid raw water, the minimum flow velocity can not be less than 0.6 m/s so as to avoid precipitation of
compensation.
suspended matter in water. In the actual design work, the flow velocity shall be selected in combination
with local economic conditions, as well as the cost of the pipe network and the operation and management
Maintenance costs is discounted according to the calculation period, their NPV can be summed. The sum of
costs.
CeNPVNPV sum of electricity expenses of each year within calculation period ($ 10,000)
Meanwhile, the diameter of pipes shall be selected on the basis of head loss. Through a lot of researches
and tests, Xinxing has reviewed the absolute roughness of various lining, and accordingly developed the
Cm(1+i)
CmNPV=
-t
t=1
hydraulic calculation table of ductile iron pipes with different lining for the reference of design department.
Where: Cm Annual pipeline maintenance fee, usually counted as 1% of the pipeline investment
There are many different methods to calculate economic velocity, all countries have their own calculation
methods. For water pipeline of large-scale supply & drainage project, the NPV method is usually adopted to
3)Annual electricity expenses for opeartion of pipeline in different diameters are calculated with supply water
4.2.2.1 Taken the maximum daily water amount as 100%, the statistics is conducted according to three
sections of daily water supply capacity, i.e. 100% ~ 90% (annual peak water supply period), 90% ~
80% (annual usual water supply period), <80% (annual trough period of supply). The statistics shall
cover the number and proportion of days as well as the proportion of the average daily supply quantity
CeNPV=
t1
t=1
Qr1H1f1+Qr2H2f2+Qr3H3f3
t
(1+i)
+
t=t1+1
Qr1H1f1+Qr2H2f2+Qr3H3f3
t
(1+i)
dx
24x365
102x86.4
in different water supply periods to the highest daily water supply quantity. Through research on the
variation characteristics of daily water supply within one year, the annual characteristics values of water
quantity variation can be summarized, which can reflect the magnitude of diurnal variation and variation
80
XINXING PIPES
81
Where Q. Q short- and long-term planning of water consumption respectively with unit in m3/d
r1, r2, r3 - ratios of the annual peak water-supply period, usual water-supply period and trough water-
H.W.L
L.W.L
Reservoir
H1 H2 H3 Pipe head losses of average daily supply water in the anuual peak period, usual
dient line
Pipe
If the starting point of a pipeline is higher than its termination point, and the height difference between
two points is larger than sum of total pipeline head loss and the smallest service water head of the most
The pump shaft power is related to the routine operating cost of pipeline project, which depends on the size
of pipe and material of the inner wall. Therefore, it shall be concerned during the engineering design. Its
formula is:
P=0.0098 x
Q x ELT
Design principle of gravity piping system: Accelerate the flow rate by means of water head difference as
possible, namely, the pipe with the minimum diameter shall be used to reduce material cost and construction
H.W.L
L.W.L
Reservoir
Pipe
If the starting point of the pipeline is not high enough and the water can not be supplied by gravity flow, it is
necessary to use the booster pump which delivers water to the water supply location.
This piping system has the following characteristics:
1)The water pressure can be easily controlled;
2)It is less affected by terrain conditions, so the pipeline route is subject to less restriction.
3)Continous power input is needed. Thus, during pipeline design, various designing options shall be
compared, and the solution with minimum sum of pipeline construction and management costs during whole
payback period of the entire project shall be selected.
82
XINXING PIPES
83
with conditions along the line. If the pressured water supply is needed due to the terrain or pipe system
layout, the stages and methods of pressure boost, booster stations shall be determined according to the
equipment selection, analysis on operation cost, as well as the technical and economic comparison.
position of pipeline;
During the pipeline selection, it is necessary to combine the near and far terms and consider possibility
of implementation by stage.
The design and laying of pipeline shall put all points along the pipeline under the minimum hydraulic
gradient. For pressure pipeline, it shall be generally below the water hydraulic gradient line under different
Start
L.W.L
mini
mum
hydr
aulic
ient
The
following factors:
Inner friction of water (depends on its viscosity);
Water friction along the pipes wall(linked to the
roughness);
Local changes to flow (elbows, joints, etc.).
Head loss consists of the linear loss and local loss.
When the certain points of the pipeline are inevitably higher than the minimum hydraulic gradient,
the pipe diameter shall be increased in the upstream section to reduce the friction loss so as to raise the
minimum hydraulic gradient of the pipeline, and then the diameter of downstream pipeline shall be reduced.
H.W.L
Start
L.W.L
imum h
gradien
h2
ydraulic
h1
The min
1) Darcy formula
hf = *
2g
84
XINXING PIPES
85
The formula applies to the laminar and turbulent flow in the smooth or rough pipe with any cross-sectional
shapes, and the linear head loss factor in the formula is generally calculated by C. F. Colebrook formula.
The minor head losses from fittings (elbows, tees, etc.) and valves accounts for less proportion in the total
head losses in a long pipeline: For a long-distance waterline, the head losses from pipe fittings can be
=-21og(
k
3.7D
2.51
Re
estimated as 5% ~ 10% of the linear losses of the pipeline according to number of fittings; however, for the
pipeline with short length and higher flow rate, the head losses from fittings may be relatively larger, which
Hf=
1.8518
(3.5875 Q/ChD2.63)
shall be considered. The local head losses of fittings can be calculated by the following formula:
hj =
Chhazen-Willian factor
Rereynolds number
vvelocity (m/s)
2) Hazen-Willian formula
v
2g
No.
Item
drawing
A2
engineering design, which directly affects the accuracy of the hydraulic calculation.
No matter in Darcy Formula or Hazen - William Formula, the difference of pipe materials is reflected on the
absolute roughness of the inner wall. In each formula, the value of the roughness correlation coefficient is
an important factor affecting the calculating results.
Generally, the cement mortar is selected as the lining material of ductile iron pipe. The cement mortar
A1
1-
Pipe outlet
lining have been smooth, even and flat with strong bonding with the wall and sound hydraulic performance.
A2
1-
=0.5
A1
= 1-
A1
A2
Xinxing has conducted a series of tests on friction coefficient and checked the surface roughness value k
and Hazen-Willian coefficientChof ductile iron pipes lined with different materials. For cement mortar lined
ductile iron pipe, a K value of 0.03 can be used; however, for actual piping design purposes, the values of
friction coefficient are recommended for different lining materials as table belows:
=K
4
A2
A1
-1
8
0.14
e/d
e/d
0.7
0.44
10
0.16
15
25
0.30 0.62
86
Sluice valve
0.2
35
0.8
0.17
0.4
4.6
0.9
0.0
0.6
0.98
1.0
0
Hazen-Willian factor Ch
PU lining
0.03~0.05
140~145
0.05~0.07
133~137
For the minor losses of the valve, please consult suppliers of valves; for calculation of other types of local
0.07~0.1
125~130
XINXING PIPES
87
Table of Head Loss of DN100 Ductile Iron Pipes With Different Lining Materials
To meet the relevant design needs, we have calculated the head losses of ductile iron pipe lined with
cement mortar and 1mm polyurethane in thickness under the following assumptions, which are shown in the
table below in details(where, hydraulic gradient J is the head losses for unit length of pipeline, thus, J =
hf
Q(l/s)
J(m/km)
V(m/s)
V(m/s)
4.0
3.19
0.51
3.09
0.51
2.26
0.45
4.5
3.97
0.57
3.82
0.57
2.81
0.51
5.0
4.84
0.64
4.66
0.64
3.40
0.57
5.5
5.79
0.70
5.56
0.70
4.04
0.62
6.0
6.83
0.76
6.53
0.76
4.75
0.68
6.5
7.94
0.83
7.59
0.83
5.52
0.74
7.0
9.13
0.89
8.72
0.89
6.31
0.79
7.5
10.43
0.95
9.92
0.95
7.17
0.85
8.0
11.77
1.02
11.24
1.02
8.08
0.91
8.5
13.22
1.08
12.57
1.08
9.08
0.96
9.0
14.76
1.15
14.02
1.15
10.08
1.02
9.5
16.37
1.21
15.55
1.21
11.17
1.08
10.0
18.05
1.27
17.06
1.27
12.26
1.13
10.5
19.81
1.34
18.72
1.34
13.44
1.19
11.0
21.65
1.40
20.45
1.40
14.68
1.25
11.5
23.55
1.46
22.35
1.46
15.96
1.30
12.0
25.52
1.53
24.21
1.53
17.29
1.36
12.5
27.69
1.59
26.14
1.59
18.67
1.42
13.0
29.81
1.66
28.14
1.66
20.09
1.47
13.5
32.15
1.72
30.34
1.72
21.55
1.53
14.0
34.41
1.78
32.47
1.78
23.17
1.59
14.5
36.92
1.85
34.66
1.85
24.73
1.64
15.0
39.32
1.91
37.09
1.91
26.33
1.70
15.5
41.99
1.97
39.40
1.97
28.11
1.76
16.0
44.53
2.04
41.99
2.04
29.79
1.81
16.5
47.35
2.10
44.43
2.10
31.52
1.87
17.0
50.27
2.16
47.16
2.16
33.46
1.93
17.5
53.01
2.23
49.98
2.23
35.27
1.98
18.0
56.09
2.29
52.61
2.29
37.31
2.04
18.5
59.24
2.36
55.57
2.36
39.20
2.10
19.0
62.19
2.42
58.31
2.42
41.35
2.15
19.5
65.51
2.48
61.42
2.48
43.55
2.21
20.0
68.91
2.55
64.61
2.55
45.57
2.27
20.5
72.05
2.61
67.54
2.61
47.87
2.32
21.0
75.61
2.67
70.87
2.67
49.97
2.38
22.0
82.98
2.80
77.78
2.80
54.84
2.49
23.0
90.26
2.93
84.58
2.93
59.61
2.61
75.34
2.95
26.0
* Head (in meters) of the fluid as it flows through a standard kilometer of the relevant pipe.
88
XINXING PIPES
89
Table of Head Loss of DN400 Ductile Iron Pipes With Different Lining Materials
Q(l/s)
Table of Head loss of DN600 Ductile Iron Pipes With Different Lining Materials
Q(l/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
60
0.51
0.48
0.50
0.48
0.44
0.46
140
0.34
0.50
0.33
0.50
0.30
0.48
65
0.59
0.52
0.58
0.52
0.51
0.50
160
0.43
0.57
0.42
0.57
0.39
0.55
70
0.69
0.56
0.67
0.56
0.59
0.54
180
0.54
0.64
0.53
0.64
0.48
0.62
75
0.78
0.60
0.76
0.60
0.67
0.57
200
0.66
0.71
0.64
0.71
0.58
0.69
80
0.88
0.64
0.85
0.64
0.76
0.61
220
0.79
0.78
0.76
0.78
0.70
0.76
85
0.99
0.68
0.95
0.68
0.85
0.65
240
0.93
0.85
0.90
0.85
0.82
0.83
90
1.10
0.72
1.06
0.72
0.94
0.69
260
1.08
0.92
1.05
0.92
0.95
0.90
95
1.22
0.76
1.18
0.76
1.04
0.73
280
1.25
0.99
1.20
0.99
1.10
0.96
100
1.34
0.80
1.30
0.80
1.14
0.76
300
1.42
1.06
1.37
1.06
1.25
1.03
110
1.61
0.88
1.55
0.88
1.37
0.84
320
1.60
1.13
1.55
1.13
1.41
1.10
120
1.90
0.95
1.83
0.95
1.60
0.92
340
1.81
1.20
1.74
1.20
1.58
1.17
130
2.22
1.03
2.12
1.03
1.87
0.99
360
2.02
1.27
1.93
1.27
1.76
1.24
140
2.54
1.11
2.44
1.11
2.16
1.07
380
2.23
1.34
2.14
1.34
1.95
1.31
150
2.91
1.19
2.79
1.19
2.44
1.15
400
2.47
1.41
2.37
1.41
2.14
1.38
160
3.29
1.27
3.15
1.27
2.76
1.22
420
2.71
1.49
2.60
1.49
2.36
1.45
170
3.70
1.35
3.53
1.35
3.09
1.30
440
2.97
1.56
2.85
1.56
2.57
1.52
180
4.12
1.43
3.93
1.43
3.45
1.38
460
3.23
1.63
3.09
1.63
2.79
1.58
190
4.59
1.51
4.38
1.51
3.81
1.45
480
3.51
1.70
3.37
1.70
3.04
1.65
200
5.05
1.59
4.83
1.59
4.22
1.53
500
3.81
1.77
3.63
1.77
3.27
1.72
210
5.57
1.67
5.28
1.67
4.62
1.61
520
4.09
1.84
3.92
1.84
3.54
1.79
220
6.07
1.75
5.80
1.75
5.04
1.68
540
4.42
1.91
4.20
1.91
3.78
1.86
230
6.64
1.83
6.30
1.83
5.51
1.76
560
4.75
1.98
4.52
1.98
4.07
1.93
240
7.18
1.91
6.86
1.91
5.96
1.84
580
5.06
2.05
4.84
2.05
4.37
2.00
250
7.79
1.99
7.39
1.99
6.46
1.91
600
5.41
2.12
5.15
2.12
4.64
2.07
260
8.37
2.07
7.99
2.07
6.94
1.99
620
5.78
2.19
5.49
2.19
4.95
2.14
270
9.03
2.15
8.62
2.15
7.49
2.07
640
6.12
2.26
5.85
2.26
5.28
2.20
280
9.71
2.23
9.20
2.23
7.99
2.14
660
6.50
2.33
6.23
2.33
5.57
2.27
290
10.42
2.31
9.87
2.31
8.57
2.22
680
6.90
2.41
6.56
2.41
5.91
2.34
300
11.07
2.39
10.57
2.39
9.11
2.29
700
7.32
2.48
6.95
2.48
6.26
2.41
310
11.83
2.47
11.21
2.47
9.73
2.37
720
7.74
2.55
7.35
2.55
6.57
2.48
320
12.60
2.55
11.94
2.55
10.37
2.45
740
8.12
2.62
7.77
2.62
6.94
2.55
330
13.40
2.63
12.70
2.63
10.94
2.52
760
8.56
2.69
8.13
2.69
7.32
2.62
340
14.13
2.71
13.39
2.71
11.62
2.60
780
9.02
2.76
8.57
2.76
7.71
2.69
350
14.98
2.79
14.18
2.79
12.31
2.68
800
9.49
2.83
9.01
2.83
8.05
2.76
360
15.84
2.86
15.01
2.86
12.93
2.75
820
9.97
2.90
9.47
2.90
8.46
2.82
370
16.74
2.94
15.85
2.94
13.66
2.83
840
10.46
2.97
9.93
2.97
8.88
2.89
380
17.65
3.02
16.60
3.02
14.41
2.91
* Head (in meters) of the fluid as it flows through a standard kilometer of the relevant pipe.
* Head (in meters) of the fluid as it flows through a standard kilometer of the relevant pipe.
90
XINXING PIPES
91
Table of Head Loss of DN1000 Ductile Iron Pipes With Different Lining Materials
Q(m3/s)
Table of Head Loss of DN1600 Ductile Iron Pipes With Different Lining Materials
J(m/km)
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
0.10
0.50
0.10
0.50
0.10
0.49
0.22
1.1
0.13
0.55
0.12
0.55
0.11
0.54
0.62
0.26
1.2
0.15
0.60
0.14
0.60
0.13
0.59
0.70
0.69
0.32
1.3
0.17
0.65
0.17
0.65
0.16
0.63
0.40
0.76
0.75
0.37
1.4
0.20
0.70
0.19
0.70
0.18
0.68
0.83
0.47
0.83
0.81
0.43
1.5
0.23
0.75
0.22
0.75
0.20
0.73
0.55
0.89
0.54
0.89
0.87
0.50
1.6
0.26
0.80
0.25
0.80
0.23
0.78
0.75
0.63
0.95
0.61
0.95
0.94
0.57
1.7
0.29
0.85
0.28
0.85
0.26
0.83
J(m/km)
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
0.4
0.19
0.51
0.19
0.51
0.50
0.18
0.45
0.24
0.57
0.23
0.57
0.56
0.5
0.29
0.64
0.28
0.64
0.55
0.35
0.70
0.34
0.6
0.41
0.76
0.65
0.48
0.7
0.8
0.71
1.02
0.69
1.02
1.00
0.64
1.8
0.32
0.90
0.31
0.90
0.29
0.88
0.85
0.80
1.08
0.77
1.08
1.06
0.72
1.9
0.35
0.94
0.34
0.94
0.32
0.93
0.9
0.89
1.15
0.86
1.15
1.12
0.80
0.39
0.99
0.38
0.99
0.35
0.98
0.95
0.99
1.21
0.96
1.21
1.19
0.88
2.1
0.43
1.04
0.42
1.04
0.39
1.02
1.09
1.27
1.05
1.27
1.25
0.97
2.2
0.47
1.09
0.45
1.09
0.42
1.07
1.05
1.20
1.34
1.16
1.34
1.31
1.07
2.3
0.51
1.14
0.49
1.14
0.46
1.12
1.1
1.31
1.40
1.26
1.40
1.37
1.17
2.4
0.55
1.19
0.53
1.19
0.49
1.17
1.15
1.44
1.46
1.37
1.46
1.44
1.27
2.5
0.60
1.24
0.58
1.24
0.54
1.22
1.2
1.55
1.53
1.49
1.53
1.50
1.38
2.6
0.65
1.29
0.62
1.29
0.58
1.27
1.25
1.68
1.59
1.62
1.59
1.56
1.49
2.7
0.69
1.34
0.67
1.34
0.62
1.32
1.3
1.81
1.66
1.74
1.66
1.62
1.60
2.8
0.74
1.39
0.72
1.39
0.66
1.37
1.35
1.95
1.72
1.87
1.72
1.69
1.73
2.9
0.80
1.44
0.77
1.44
0.71
1.41
1.4
2.10
1.78
2.00
1.78
1.75
1.84
0.85
1.49
0.82
1.49
0.76
1.46
1.45
2.25
1.85
2.15
1.85
1.81
1.98
3.2
0.96
1.59
0.92
1.59
0.86
1.56
1.5
2.39
1.91
2.30
1.91
1.87
2.11
3.4
1.08
1.69
1.03
1.68
0.96
1.66
1.55
2.55
1.97
2.45
1.97
1.93
2.24
3.6
1.21
1.79
1.14
1.78
1.07
1.76
1.6
2.72
2.04
2.59
2.04
2.00
2.38
3.8
1.35
1.89
1.27
1.88
1.19
1.85
1.65
2.89
2.10
2.76
2.10
2.06
2.54
1.48
1.99
1.39
1.97
1.31
1.95
1.7
3.04
2.16
2.93
2.16
2.12
2.67
4.2
1.63
2.09
1.53
2.07
1.43
2.05
1.75
3.23
2.23
3.07
2.23
2.18
2.83
4.4
1.79
2.19
1.67
2.17
1.57
2.15
1.8
3.41
2.29
3.25
2.29
2.25
2.99
4.6
1.94
2.29
1.81
2.26
1.71
2.24
1.85
3.61
2.36
3.44
2.36
2.31
3.16
4.8
2.12
2.39
1.96
2.36
1.86
2.34
1.9
3.80
2.42
3.62
2.42
2.37
3.31
2.30
2.49
2.12
2.45
2.01
2.44
1.95
3.97
2.48
3.82
2.48
2.43
3.48
5.2
2.48
2.59
2.27
2.55
2.16
2.54
4.18
2.55
3.98
2.55
2.50
3.66
5.4
2.65
2.69
2.44
2.64
2.33
2.63
2.1
4.61
2.67
4.39
2.67
2.62
4.00
5.6
2.85
2.79
2.61
2.74
2.50
2.73
2.2
5.06
2.80
4.82
2.80
2.75
4.39
5.8
3.06
2.88
2.80
2.83
2.69
2.83
2.3
5.49
2.93
5.22
2.93
2.87
4.80
3.28
2.98
2.96
2.93
2.85
2.93
2.4
5.97
3.06
5.69
3.06
3.00
5.18
6.2
3.50
3.08
3.15
3.02
3.04
3.02
* Head (in meters) of the fluid as it flows through a standard kilometer of the relevant pipe.
92
Q(m3/s)
XINXING PIPES
* Head (in meters) of the fluid as it flows through a standard kilometer of the relevant pipe.
93
Table of Head Loss of DN2000 Ductile Iron Pipes With Different Lining Materials
Q(m3/s))
V(m/s)
J(m/km)
V(m/s)
J(m/km)
V(m/s)
1.6
0.08
0.51
0.08
0.51
0.08
0.50
1.8
0.10
0.57
0.10
0.57
0.10
0.56
0.13
0.64
0.12
0.64
0.12
0.63
2.2
0.15
0.70
0.15
0.70
0.14
0.69
2.4
0.18
0.76
0.18
0.76
0.17
0.75
collapsing).
2.6
0.21
0.83
0.21
0.83
0.19
0.81
Cutoff water hammer (due to cavities collapsing) when pressure somewhere of the pipeline is lower
2.8
0.24
0.89
0.24
0.89
0.22
0.88
than the saturated vapor pressure under the current water temperature, water will vaporize, destroying
0.28
0.95
0.27
0.95
0.25
0.94
3.2
0.31
1.02
0.30
1.02
0.29
1.00
continuity of water flow and causing the water column separation, which forms acavity section here. When
3.4
0.35
1.08
0.34
1.08
0.32
1.07
3.6
0.39
1.15
0.38
1.15
0.36
1.13
3.8
0.43
1.21
0.42
1.21
0.40
1.19
0.48
1.27
0.46
1.27
0.43
1.25
4.2
0.53
1.34
0.51
1.34
0.48
1.32
4.4
0.58
1.40
0.56
1.40
0.52
1.38
4.6
0.63
1.46
0.61
1.46
0.57
1.44
4.8
0.68
1.53
0.66
1.53
0.61
1.50
0.74
1.59
0.71
1.59
0.67
1.57
5.2
0.80
1.66
0.77
1.66
0.71
1.63
5.4
0.86
1.72
0.82
1.72
0.77
1.69
5.6
0.92
1.78
0.89
1.78
0.83
1.75
5.8
0.99
1.85
0.95
1.85
0.88
1.82
1.06
1.91
1.01
1.91
0.94
1.88
6.2
1.13
1.97
1.08
1.97
1.01
1.94
6.4
1.19
2.04
1.15
2.04
1.06
2.00
6.6
1.27
2.10
1.22
2.10
1.13
2.07
6.8
1.34
2.16
1.28
2.16
1.20
2.13
If the pipeline pressure drops and affects normal water supply, sewage will be drawn in at the pipeline
1.42
2.23
1.36
2.23
1.27
2.19
7.2
1.51
2.29
1.44
2.29
1.33
2.26
7.4
1.58
2.36
1.52
2.36
1.41
2.32
7.6
1.66
2.42
1.60
2.42
1.48
2.38
7.8
1.75
2.48
1.67
2.48
1.56
2.44
1.84
2.55
1.76
2.55
1.64
2.51
8.4
2.03
2.67
1.94
2.67
1.79
2.63
8.8
2.23
2.80
2.13
2.80
1.97
2.76
9.1
2.36
2.90
2.28
2.90
2.11
2.85
9.5
2.58
3.02
2.46
3.02
2.27
2.98
cause water pressure to rise dramatically, which will damage pump, valve and pipe, etc.; conversely, if the
water pressure drops dramatically, it can also form phenomenon of cutoff water hammer (due to cavities
the separated water column is re-bridged or the cavity section is re-filled with water flow, violent collision
between two water columns can produce a high-pressure cutoff water hammer (due to cavities collapsing).
Water hammer can occur in the gravity pipeline or pressure (deliveried by pump) pipeline.
N
H1
H2
Pressure line at
normal working condition
R
C
F
B
R
A
Pump Check valve
XINXING PIPES
interruption of water flow in the pressure pipeline system, and spread in the pipeline. Water hammer may
Maximum vacuum
at point B
Water hammer refers dramatical pressure change of water flow in the pipeline caused by sudden
* Head (in meters) of the fluid as it flows through a standard kilometer of the relevant pipe.
94
4.5.1 Overview
J(m/km)
95
a=
y
g
1
K
D
Ee
L
Ln
an
96
XINXING PIPES
97
2L
a
(s)
types of pipe trenches are assumed. Some calculation results are shown in the table below, which can be
In general, if the allowable depths of cover is not adequate in height, pipes with higher pressure level shall
4.5.5.3 Simplified calculation method of water hammer resulting from valve opening or
closing
1) Simple calculation on water hammer resulting from swift opening or closing valve
(Under the conditions of the valve switching time: T <Tf )
a
H -H0= (V-VO)
g
2) Simple calculation on water hammer resulting from slowly opening or closing valve
(Under the conditions of the valve switching time: T Tf )
In this case where a national standard exists for the traffic loadings, the value of may be given as follows:
=P/100
Where: P is the wheel load, in kilonewtons, for a particular type of load according to the respective national
2La
H -H0= (V-VO)
gt
standard.
For all pipelines, shall be designed as 0.5 at least, while the pipelines adjacent to the road shall be
When all valves are closed and v = 0, H-Ho=a.vo/g is the maximum additional pressure resulting from water
requirements shall be added according to the respective national standards and regulations construction.
hammer.
Soil classification
These simplified formulas provide assessment methods for maximum water hammer with the issues must
The following soil groups classify different soils for embedments, i.e. soils which are used for placement
be considered as below:
in the trench surrounding the pipe, compacted or uncompacted, to provide support for the pipeline. These
Assumptions: there are protection measures available for pipeline against water hammer and the head
groups classify naturally occurring soils as well as manufactured materials. The groups are also for use in
loss is negligible. In addition, no constraint is considered, such as pump turbine operation, pressure drop of
Soil group A: angular graded stone (6 mm to 40 mm), also including a number of fill materials which have
regional significance, such as crushed stone, crushed gravel, pea gravel and crushed shells.
Soil group B: coarse; grained soils with little or no fines. No particles larger than 40 mm.
Soil group C: coarse; grained soils with fines and fine-grained soils with medium to no plasticity, with
more than 25 % coarse particles, liquid limit less than 50 %.
Soil group D: fine; grained soils with medium to no plasticity, with less than 25 % coarse particles, liquid
limit less than 50 %.
Soil group E: fine; grained soils with medium to high plasticity, liquid limit greater than 50 %.
factors leading to water hammer shall be found in time to eliminate the hidden dangers, so that the pump
station can be safely and economicaly operated.
98
XINXING PIPES
99
8,8/8,8/8,6
9,1/9,0/8,9
10,5/10,5/10,4
13,8/13,7/13,7
19,9/19,9/19,8
7,1/7,0/6,8
7,3/7,3/7,0
8,7/8,7/8,5
11,2/11,2/11,1
15,6/15,5/15,5
5,3/5,3/5,0
6,1/6,0/5,8
6,9/6,8/6,6
8,7/8,6/8,4
12,7/12,7/12,6
4,8/4,7/4,3
5,5/5,4/5,2
6,3/6,2/6,0
8,0/7,9/7,8
10,5/10,5/10,3
E/F
4,2/4,0/3,7
4,3/4,2/3,8
4,4/4,3/4,0
4,8/4,7/4,3
5,4/5,3/5,1
trench type 4: embedment with medium compaction, greater than 85 % standard Proctor density;
7,9/7,9/7,7
8,2/8,1/8,0
9,6/9,6/9,5
12,8/12,8/12,7
18,8/18,8/18,7
trench type 5: embedment with high compaction, greater than 90 % standard Proctor density.
6,2/6,2/5,9
6,4/6,3/6,1
7,8/7,8/7,6
10,3/10,2/10,1
14,5/14,4/14,4
4,5/4,4/4,0
5,2/5,1/4,8
6,0/5,9/5,7
7,7/7,6/7,4
11,6/11,6/11,5
3,9/3,7/3,3
4,6/4,5/4,2
5,4/5,3/5,0
7,0/7,0/6,8
9,4/9,4/9,3
E/F
3,3/3,1/2,6c
3,4/3,2/2,7c
3,5/3,3/2,9c
3,7/3,6/3,2
4,3/4,2/3,8
7,4/7,4/7,2
7,7/7,6/7,4
9,1/9,0/8,9
12,2/12,2/12,1
18,2/18,1/18,1
5,7/5,6/5,4
5,9/5,8/5,6
7,3/7,2/7,0
9,7/9,6/9,5
13,8/13,8/13,7
3,9/3,8/3,5
4,7/4,6/4,3
5,4/5,4/5,1
7,1/7,0/6,8
10,9/10,9/10,8
3,3/3,2/2,7c
4,1/4,0/3,6
4,8/4,8/4,4
6,4/6,4/6,2
8,8/8,7/8,6
2,8/2,7/ d
2,9/2,7/ d
3,2/3,0/2,5c
3,6/3,5/3,1
800
trench type 2: embedment with very light compaction, greater than 75 % standard Proctor density;
trench type 3: embedment with light compaction, greater than 80 % standard Proctor density;
NOTE: Pipes are normally placed on a flat-bottomed trench when a suitable uniform support can be
1000
Allowable Depth of Cover for K9 Cement Mortar Lining Pipes Conforming to ISO 2531-1998
1200
100
200
300
500
100
XINXING PIPES
(=0.5/0.75/1.5)a
Soil Type
Trench Type 1
Trench Type 2
Trench Type 3
Trench Type 4
Trench Type 5
E/F
2,7/2,5/ d
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
7,0/6,9/6,7
7,2/7,1/7,0
8,6/8,6/8,4
11,7/11,7/11,6
17,6/17,5/17,5
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
5,3/5,2/4,9
5,4/5,3/5,1
6,8/6,8/6,5
9,2/9,1/9,0
13,3/13,2/13,1
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
3,5/3,3/3,0
4,2/4,1/3,8
5,0/4,9/4,6
6,6/6,5/6,3
10,4/10,3/10,2
50b/50b
50b/50b
50b/50b
50b/50b
50b/50b
2,9/2,7/2,1c
3,6/3,5/3,1
4,3/4,3/3,9
5,9/5,9/5,7
8,2/8,2/8,0
/50b
/50b
/50b
/50b
1500
/50b
E/F
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
50b/50b /50b
E/F
2,2/2,0/ d
2,3/2,1/ d
2,4/2,2/ d
2,6/2,4/ d
3,0/2,9/2,3c
18.9/18.8/18.7
19.4/19.4/19.3
20.6/20.6/20.5
23.1/23.0/23.0
28.1/28.1/28.0
6,7/6,7/6,5
6,9/6,8/6,7
8,3/8,3/8,2
11,4/11,4/11,3
17,2/17,2/17,1
18.1/18.0/17.9
18.6/18.6/18.5
19.7/19.7/19.6
21.8/21.8/21.7
26.1/26.0/26.0
5,0/4,9/4,7
5,1/5,1/4,8
6,5/6,4/6,3
8,8/8,8/8,7
12,9/12,9/12,8
17.2/17.2/17.1
18.0/18.0/17.9
18.8/18.8/18.7
20.6/20.6/20.5
24.7/24.7/24.6
3,2/3,1/2,7
3,9/3,8/3,5
4,7/4,6/4,3
6,3/6,2/6,0
10,0/10,0/9,9
17.0/17.0/16.9
17.7/17.7/17.7
18.6/18.5/18.5
20.3/20.3/20.2
23.7/23.7/23.6
2,6/2,4/ d
3,3/3,2/2,8
4,0/4,0/3,7
5,6/5,6/5,3
7,8/7,8/7,7
E/F
16.7/16.7/16.6
17.2/17.2/17.1
17.7/17.7/17.6
18.8/18.8/18.7
21.3/21.2/21.2
E/F
1,9/1,7/ d
2,0/1,8/ d
2,1/1,9/ d
2,3/2,1/ d
2,7/2,5/1,9c
13.3/13.2/13.1
13.6/13.6/13.5
14.8/14.8/14.7
17.3/17.3/17.2
22.3/22.2/22.2
6,6/6,5/6,4
6,8/6,7/6,6
8,2/8,1/8,0
11,3/11,2/11,2
17,0/17,0/17,0
12.2/12.2/12.0
12.5/12.5/12.4
13.7/13.6/13.5
15.7/15.7/15.6
19.6/19.6/19.5
4,8/4,8/4,5
5,0/4,9/4,7
6,3/6,3/6,2
8,7/8,7/8,6
12,7/12,7/12,6
11.1/11.1/10.9
11.8/11.8/11.7
12.5/12.5/12.4
14.1/14.1/14.0
17.8/17.7/17.7
3,1/3,0/2,6
3,8/3,7/3,4
4,5/4,5/4,2
6,1/6,1/5,9
9,8/9,8/9,7
10.8/10.7/10.6
11.4/11.4/11.3
12.2/12.1/12.0
13.7/13.7/13.6
16.4/16.4/16.3
2,5/2,3/ d
3,2/3,1/2,7
3,9/3,8/3,5
5,5/5,4/5,2
7,7/7,6/7,5
E/F
10.4/10.4/10.2
10.7/10.7/10.5
11.0/11.0/10.9
11.8/11.7/11.6
13.3/13.3/13.1
E/F
1,8/1,6/ d
1,8/1,7/ d
2,0/1,7/ d
9.8/9.8/9.7
10.1/10.1/10.0
11.4/11.4/11.3
14.2/14.2/14.1
19,6/19,6/19,5
8.5/8.4/8.2
8.7/8.7/8.5
9.9/9.9/9.8
12,2/12,1/12,0
16,1/16,1/16,0
7.1/7.0/6.8
7.8/7.7/7.5
8.5/8.4/8.2
10,1/10,0/9,9
13,8/13,7/13,6
6.6/6.5/6.3
7.3/7.2/7.0
8.0/7.9/7.7
9,5/9,5/9,3
12,0/11,9/11,8
E/F
6.1/6.0/5.8
6.3/6.2/6.0
6.5/6.4/6.2
6,9/6,9/6,6
7,8/7,8/7,6
1800
2000
2,1/1,9/
2,5/2,3/ d
Notes: a. The traffic load factors applicable to all burial depths are given as 0.5, 0.75 and 1.5;
b. The allowable burial depth exceeds 50 m;
c. The min burial depth must be more than 1 m;
d. Not recommended.
101
Allowable Depth of Cover for Class-C Cement Mortar Lining Pipes Conforming to ISO 2531-1998
Allowable Depth of Cover/m
DN/mm
80
100
125
150
200
250
102
XINXING PIPES
300
(=0.5/0.75/1.5)a
Soil Type
Trench Type 1
Trench Type 2
Trench Type 3
Trench Type 4
Trench Type 5
39.4/39.4/39.4
40.5/40.5/40.5
42.1/42.1/42.0
45.5/45.5/45.4
d/d/d
38.9/38.9/38.9
40.0/40.0/40.0
41.6/41.5/41.5
44.7/44.7/44.7
d/d/d
38.4/38.4/38.3
39.7/39.7/39.6
41.0/41.0/41.0
44.0/44.0/43.9
d/d/d
38.2/38.2/38.2
39.5/39.5/39.4
40.8/40.8/40.8
43.8/43.8/43.7
49.9/49.9/49.8
E/F
38.1/38.1/38.0
39.2/39.2/39.1
40.3/40.3/40.3
42.8/42.8/42.8
48.4/48.4/48.3
27.3/27.3/27.2
28.1/28.1/28.0
29.3/29.3/29.3
32.1/32.1/32.0
37.8/37.8/37.8
26.7/26.7/26.5
27.4/27.4/27.4
28.7/28.7/28.6
31.2/31.2/31.1
36.3/36.3/36.2
26.1/26.1/26.0
27.0/27.0/27.0
28.0/28.0/28.0
30.3/30.3/30.2
35.2/35.2/35.2
25.9/25.8/25.8
26.8/26.8/26.7
27.8/27.8/27.8
30.0/30.0/30.0
34.5/34.4/34.4
E/F
25.7/25.6/25.6
26.4/26.4/26.3
27.2/27.2/27.1
28.9/28.9/28.8
32.6/32.6/32.6
19.9/19.9/19.8
20.4/20.4/20.3
21.6/21.6/21.5
24.0/24.0/23.9
29.0/29.0/29.0
19.1/19.1/19.0
19.7/19.7/19.6
20.8/20.8/20.7
22.9/22.9/22.8
27.1/27.1/27.1
18.4/18.4/18.3
19.2/19.2/19.1
20.0/20.0/19.9
21.8/21.8/21.7
25.9/25.9/25.8
18.2/18.1/18.0
18.9/18.9/18.8
19.7/19.7/19.6
21.5/21.5/21.4
25.0/24.9/24.8
E/F
17.9/17.9/17.8
18.4/18.4/18.3
19.0/18.9/18.9
20.2/20.2/20.1
22.8/22.8/22.7
14.9/14.9/14.8
15.4/15.3/15.2
16.4/16.4/16.3
18.8/18.7/18.7
23.4/23.4/23.4
14.0/14.0/13.9
14.5/14.4/14.3
15.5/15.5/15.4
17.5/17.4/17.4
21.2/21.2/21.1
13.2/13.1/13.0
13.9/13.8/13.7
14.6/14.5/14.4
16.1/16.1/16.0
19.7/19.7/19.6
12.9/12.8/12.7
13.6/13.5/13.4
14.3/14.2/14.1
15.8/15.8/15.7
18.6/18.6/18.5
E/F
12.8/12.5/12.4
12.9/12.9/12.8
13.3/13.3/13.2
14.2/14.1/14.0
16.0/1.06/15.9
10.9/10.8/10.7
11.2/11.1/11.0
12.3/12.3/12.1
14.7/14.7/14.6
19.5/19.4/19.4
9.8/9.7/9.6
10.1/10.0/9.9
11.1/11.1/11.0
13.1/13.0/12.9
16.7/16.6/16.6
8.7/8.6/8.4
9.3/9.2/9.1
10.0/9.9/9.8
11.4/11.4/11.3
14.8/14.8/14.7
8.3/8.2/8.0
8.9/8.9/8.7
9.6/9.5/9.4
11.0/11.0/10.8
13.4/13.4/13.3
E/F
7.9/7.9/7.7
8.1/8.1/7.9
8.4/8.3/8.2
8.9/8.9/8.7
10.1/10.1/9.9
10.6/10.5/10.4
10.9/10.8/107
12.0/12.0/11.9
14.6/14.5/14.4
19.4/19.4/19.3
9.4/9.4/9.2
9.7/9.6/9.5
10.8/10.8/10.6
12.8/12.8/12.7
16.5/16.4/16.3
8.2/8.2/8.0
8.9/8.8/8.7
9.6/9.5/9.4
11.1/11.0/10.9
14.5/14.5/14.4
7.8/7.8/7.6
8.5/8.4/8.3
9.2/9.1/8.9
10.6/10.6/10.4
13.0/13.0/12.9
E/F
7.5/7.4/7.2
7.7/7.6/7.4
7.9/7.9/7.7
8.4/8.4/8.2
9.5/9.5/9.3
350
400
450
500
600
700
10.4/10.3/10.2
107/10.6/10.5
11.9/11.9/11.7
14.5/14.4/14.3
19.5/19.5/19.4
9.1/9.1/8.9
9.4/9.4/9.2
10.6/10.5/10.4
12.6/12.6/12.5
16.4/16.3/16.2
7.9/7.8/7.6
8.6/8.5/8.3
9.3/9.2/9.0
10.8/10.7/10.6
14.3/14.2/14.1
7.5/7.4/7.2
8.1/8.1/7.9
8.8/8.8/8.6
10.3/10.3/10.1
12.7/12.7/12.6
E/F
7.1/7.0/6.8
7.3/7.2/7.0
7.5/7.4/7.2
8.0/7.9/7.7
9.1/9.0/8.8
8.5/8.5/8.3
8.8/8.7/8.5
10.0/9.9/9.8
12.6/12.5/12.4
17.6/17.6/17.4
7.2/7.1/6.9
7.4/7.3/7.1
8.6/8.5/8.3
10.6/10.6/10.4
14.2/14.2/14.1
5.8/5.8/5.5
6.5/6.4/6.2
7.1/7.1/6.9
8.6/8.6/8.4
12.0/12.0/11.8
5.4/5.3/5.0
6.0/5.9/5.7
6.7/6.6/6.4
8.1/8.1/7.9
10.3/10.3/10.1
E/F
4.9/4.8/4.5
5.1/5.0/4.7
5.2/5.2/4.9
5.6/5.5/5.2
6.4/6.3/6.1
7.4/7.4/7.2
7.7/7.6/7.4
8.9/8.8/8.6
11.5/11.4/11.3
16.5/16.4/16.3
6.1/6.0/5.7
6.2/6.2/5.9
7.4/7.3/7.1
9.4/9.4/9.2
13.0/13.0/12.8
4.7/4.5/4.2
5.3/5.2/4.9
5.9/5.9/5.6
7.4/7.3/7.1
10.7/10.6/10.5
4.2/4.1/3.7
4.8/4.7/4.4
5.4/5.4/5.1
6.9/6.8/6.6
8.9/8.9/8.7
E/F
3.7/3.6/3.1
3.8/3.7/3.2
4.0/3.8/3.4
4.2/4.1/3.7
4.8/4.7/4.4
7.1/7.0/6.8
7.3/7.3/7.1
8.5/8.5/8.3
11.2/11.2/11.0
16.3/16.2/16.1
5.7/5.6/5.3
5.9/5.8/5.5
7.0/7.0/6.8
9.1/9.0/8.9
12.7/12.7/12.5
4.2/4.1/3.7
4.9/4.8/4.4
5.5/5.4/5.2
7.0/6.9/6.7
10.3/10.3/10.1
3.7/3.6/3.1
4.4/4.3/3.9
5.0/4.9/4.6
6.4/6.4/6.1
8.5/8.5/8.3
E/F
3.2/3.1/2.4 c
3.3/3.2/2.6c
3.5/3.3/2.7
3.7/3.6/3.1
4.3/4.1/3.8
7.2/7.1/6.9
7.4/7.4/7.2
8.7/8.6/8.5
11.4/11.4/11.3
16.6/16.6/16.5
5.7/5.7/5.4
5.9/5.8/5.6
7.1/7.1/6.9
9.2/9.2/9.0
12.9/12.9/12.8
4.2/4.1/3.7
4.9/4.8/4.5
5.6/5.5/5.2
7.0/7.0/6.8
10.5/10.4/10.3
3.7/3.6/3.1
4.4/4.3/3.9
5.0/5.0/4.6
6.5/6.4/6.2
8.6/8.6/8.4
E/F
3.2/3.1/2.4 c
3.3/3.2/2.6c
3.4/3.3/2.7
3.7/3.6/3.1
4.2/4.1/3.7
7.5/7.4/7.2
7.7/7.6/7.5
9.0/9.0/8.8
11.9/11.9/11.7
17.3/17.3/17.2
5.9/5.8/5.6
6.1/6.0/5.8
7.4/7.3/7.1
9.6/9.5/9.4
13.5/13.4/13.3
4.3/4.2/3.9
5.0/4.9/4.6
5.7/5.6/5.4
7.3/7.2/7.0
10.9/10.8/10.7
3.8/3.7/3.2
4.5/4.4/4.0
5.2/5.1/4.8
6.7/6.6/6.4
8.9/8.9/8.7
E/F
3.3/3.1/2.5c
3.4/3.2/2.6
3.5/3.3/2.8
3.7/3.6/3.1
4.3/4.2/3.8
6.5/6.5/6.3
6.7/6.7/6.5
8.1/8.1/7.9
11.1/11.0/10.9
16.6/16.6/16.5
4.9/4.8/4.5
5.0/5.0/4.7
6.4/6.3/6.1
8.6/8.6/8.4
12.5/12.5/12.4
3.2/3.0/2.4 c
3.9/3.8/3.4
4.6/4.5/4.2
6.26.1/5.9
9.8/9.7/9.6
2.6/2.4/d
3.3/3.2/2.6
4.0/3.9/3.5
5.6/5.5/5.2
7.7/7.6/7.5
E/F
2.0/1.6/d
2.0/1.7/d
2.1/1.8/d
2.3/2.1/d
2.7/2.5/d
103
800
900
1000
1100
1200
1400
1500
104
XINXING PIPES
6.5/6.5/6.3
6.8/6.7/6.6
8.2/8.2/8.0
11.3/11.3/11.2
17.1/17.1/17.0
5.5/5.4/5.2
5.6/5.6/5.4
7.0/6.9/6.8
10.0/10.0/9.9
15.7/15.6/15.6
4.9/4.8/4.5
5.0/4.9/4.7
6.4/6.3/6.1
8.8/8.7/8.6
12.8/12.8/12.7
3.7/3.6/3.3
3.8/3.7/3.4
5.1/5.1/4.9
7.4/7.4/7.3
11.3/11.3/11.2
3.1/2.9/2.3c
3.8/3.7/3.3
4.6/4.5/4.1
6.2/6.1/5.9
9.9/9.9/9.8
1.8/1.5/d
2.6/2.4/1.6c
3.3/3.2/2.8
4.9/4.8/4.6
8.4/8.4/8.3
2.4/2.2/d
3.2/3.0/2.4c
3.9/3.8/3.4
5.5/5.5/5.2
7.7/7.7/7.5
0.9/d/d
1.9/1.6/d
2.7/2.5/1.8c
4.2/4.1/3.8
6.3/6.2/6.0
E/F
1.8/1.2/d
1.8/1.4/d
1.9/1.6/d
2.1/1.8/d
2.5/2.3/d
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
6.5/6.5/6.3
6.7/6.7/6.5
8.2/8.1/8.0
11.3/11.2/11.1
17.1/17.0/17.0
5.4/5.4/5.2
5.6/5.5/5.3
7.0/6.9/6.8
10.0/10.0/9.9
15.6/15.6/15.5
4.8/4.7/4.4
5.0/4.9/4.6
6.3/6.3/6.1
8.7/8.6/8.5
12.7/12.7/12.6
3.7/3.6/3.3
3.8/3.7/3.4
5.1/5.1/4.9
7.4/7.4/7.2
11.3/11.3/11.2
3.0/2.9/2.3c
3.7/3.6/3.2
4.5/4.4/4.1
6.1/6.0/5.8
9.8/9.8/9.7
1.8/1.6/d
2.5/2.4/1.7c
3.3/3.2/2.8
4.8/4.8/4.6
8.4/8.4/8.3
2.4/2.2/d
3.1/3.0/2.4 c
3.9/3.8/3.4
5.5/5.4/5.1
7.7/7.6/7.4
0.9/d/d
1.9/1.6/d
2.6/2.5/1.9
4.2/4.1/3.8
6.2/6.2/6.0
E/F
1/7/d/d
1.8/1.3/d
1.8/1.5/d
2.0/1.7/d
2.4/2.2/d
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
6.5/6.4/6.2
6.7/6.6/6.4
8.1/8.1/7.9
11.2/11.2/11.0
17.0/17.0/16.9
5.4/5.4/5.2
5.6/5.5/5.4
7.0/6.9/6.8
10.0/10.0/9.9
15.6/15.6/15.5
4.8/4.7/4.4
4.9/4.8/4.5
6.3/6.2/6.0
8.6/8.6/8.4
12.7/12.6/12.5
3.7/3.6/3.3
3.8/3.7/3.4
5.1/5.1/4.9
7.4/7.4/7.2
11.3/11.3/11.2
3.0/2.8/2.1 c
3.7/3.6/3.2
4.4/4.3/4.0
6.0/6.0/5.8
9.8/9.7/9.6
1.8/1.6/d
2.6/2.4/1.8
3.3/3.2/2.8
4.8/4.8/4.6
8.4/8.4/8.3
2.3/2.1/d
3.1/2.9/2.3c
3.8/3.7/3.3
5.4/5.3/5.1
7.6/7.5/7.4
1.0/d/d
1.9/1.7/d
2.6/2.5/2.0
4.2/4.1/3.9
6.2/6.2/6.0
E/F
1.6/d/d
1.7/d/d
1.8/1.4/d
2.0/1.7/d
2.3/2.1/d
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
5.5/5.4/5.2
5.7/5.6/5.4
7.1/7.0/6.8
10.1/10.0/9.9
15.7/15.7/15.6
3.7/3.6/3.2
3.9/3.8/3.4
5.2/5.2/4.9
7.5/7.5/7.3
11.4/11.4/11.3
1.8/1.5/d
2.6/2.4/d
3.4/3.2/2.7
4.9/4.8/4.6
8.5/8.5/8.3
d/d/d
1.9/1.6/d
2.7/2.5/d
4.3/4.2/3.8
6.3/6.3/6.1
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
5.5/5.4/5.2
5.6/5.6/5.4
7.0/7.0/6.8
10.1/10.0/9.9
15.7/15.7/15.6
3.7/3.6/3.2
3.8/3.7/3.4
5.2/5.1/4.9
7.5/7.4/7.3
11.4/11.3/11.2
1.8/1.5/d
2.6/2.4/d
3.3/3.2/2.7
4.9/4.8/4.6
8.5/8.4/8.3
d/d/d
1.9/1.6/d
2.7/2.5/d
4.2/4.1/3.8
6.3/6.2/6.0
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
5.5/5.4/5.2
5.6/5.6/5.4
7.0/7.0/6.8
10.0/10.0/9.9
15.7/15.7/15.6
3.7/3.6/3.2
3.8/3.7/3.4
5.2/5.1/4.9
7.5/7.4/7.3
11.4/11.3/11.2
1.8/1.5/d
2.6/2.4/d
3.3/3.2/2.8
4.9/4.8/4.6
8.5/8.4/8.3
d/d/d
1.9/1.6/d
2.7/2.5/1.7c
4.2/4.1/3.8
6.3/6.2/6.0
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
5.4/5.4/5.2
5.6/5.5/5.3
7.0/6.9/6.8
10.0/10.0/9.9
15.7/15.6/15.6
3.7/3.6/3.2
3.8/3.7/3.4
5.2/5.1/4.9
7.5/7.4/7.3
11.3/11.3/11.2
1.8/1.5/d
2.6/2.4/d
3.3/3.2/2.8
4.9/4.8/4.5
8.4/8.4/8.3
d/d/d
1.9/1.6/d
2.6/2.5/1.7c
4.2/4.1/3.8
6.3/6.2/6.0
E/F
d/d/d
d/d/d
d/d/d
d/d/d
d/d/d
1600
1800
2000
Notes: a. The traffic load factors applicable to all the burial depths are given as 0.5, 0.75 and 1.5;
b. The allowable burial depth exceeds 50 m;
c. The min burial depth must be more than 1 m;
d. Not recommended.
105
When the pipe changes direction (at the elbow or tees), stops (at the end), or changes size (at the tapers),
hydraulic thrust will occur in the water pipeline. On this occasion, the restrictive measures shall be taken
to keep the pipeline from being affected. There are several restrictive methods available, among them, the
concrete anchor blocks and self-anchored joint are the most common methods.
The jacking force F is related to maximum field test pressure P of pipeline, sectional area of the pipe or
elbow angle, etc., which can be calculated as follows:
Where: (A-a) difference of the cross sectional areas on both ends of the reducing pipe
F
tees and
blank
flanges
11.3 bends
DN
DE(mm)
Hydraulic
pressure (bar)
90 bends
45 bends
22.5 bends
80
98
10
1.1
0.6
0.3
0.1
0.8
100
118
10
1.5
0.8
0.4
0.2
1.1
200
222
10
5.5
3.0
1.5
0.8
3.9
300
326
10
11.8
6.4
3.3
1.6
8.3
Where: P test pressure (generally maximum field test pressure, pa) as prescribed in the acceptance
400
429
10
20.4
11.1
5.6
2.8
14.5
500
532
10
31.4
17.0
8.7
4.4
22.2
600
635
10
44.8
24.2
12.4
6.2
31.7
700
738
10
60.5
32.7
16.7
8.4
42.8
800
842
10
78.7
42.6
21.7
10.9
55.7
900
945
10
99.2
53.7
27.4
13.7
70.1
1000
1048
10
122.0
66.0
33.7
16.9
86.3
1100
1152
10
147.4
79.8
40.7
20.4
104.2
1200
1255
10
174.9
94.7
48.3
24.2
123.7
1400
1462
10
237.4
128.5
65.5
32.9
167.9
1500
1565
10
272.0
147.2
75.1
37.7
192.4
1600
1668
10
309.0
167.2
85.3
42.8
218.5
1800
1875
10
390.5
211.3
107.7
54.1
276.1
2000
2082
10
481.5
260.6
132.8
66.7
340.4
criteria
A cross sectional area of the branch pipes or blank flange(m2)
4.7.1.2 Bend
(N)
1 The values of thrust F in the above table are calculated on the basis of actual OD of pipes
106
XINXING PIPES
107
4.7.2.2 anchor block for bends (including bends with various angles)
D/2 D/2
H1
200
L/2
H1 D/2 D/2
H
L/2
H5
L/2
H5
L/2
settlement joint
ground surface
H2
H2
settlement
joint
B
B
H1
H5
L/2
settlement joint
H2
ground surface
H1
L/2
D/2 D/2
H2
settlement joint
B
glass wool clothes and straw ropes
B
200
B
200
500
500
Note: anchor block horizontal bends mainly applies to pipelines with large-diameter, high testing
pressure
108
XINXING PIPES
109
reaction against the blocks, as well as friction between pipe and the
surrounding soil.
Blocks shall not be built on soft soil. For soft soil, the soil around the
S=
N+G1
(m )
[R]-H
Where, N vertical component of F (kN)
shall be less than sum of the soil reaction against the blocks at
the back of blocks and bottom friction of the blocks, i.e., KFtotal
T: T=K(T1+T2 ) (N)
Np=F * sin
f(G1+G3-N)+T1
110
XINXING PIPES
111
It is impossible to set the anchored concrete anchor blocks under some special circumstances, such as:
No sufficient space for the specified anchor blocks due to too narrow construction site;
When the pipeline is crossing a river or a bridge;
When the pipeline is crossing a swamp
DN
Dend End
90
45
22.5
11.25
Burial
depth
(m)
1.0
1.5
2.0
1.0
1.5
2.0
1.0
1.5
2.0
1.0
1.5
2.0
1.0
1.5
2.0
80
5.9
3.9
2.8
4.6
3.0
2.2
2.9
1.9
1.4
1.6
1.1
0.8
0.9
0.6
0.5
Therefore, during design and construction of ductile iron pipe, a special pipe fitting or equipment is required
100
7.2
4.8
3.5
5.6
3.7
2.7
3.5
2.3
1.7
2.0
1.3
1.0
1.0
0.7
0.5
to properly connect relevant pipes and fittings together, making the pipeline connection flexible and rigid, so
125
8.8
5.9
4.4
6.9
4.6
3.4
4.3
2.9
2.1
2.4
1.6
1.2
1.3
0.9
0.6
that the joints of pipeline at this section can pass force between each other. The friction generated between
150
10.1
6.9
5.1
8.0
5.4
4.0
4.9
3.3
2.5
2.8
1.9
1.4
1.5
1.0
0.7
200
13.4
9.1
6.9
10.5
7.2
5.4
6.5
4.5
3.4
3.7
2.5
1.9
1.9
1.3
1.0
the pipeline and the surrounding soil can effectively offset the stress generated in the axial and radial
250
16.4
11.4
8.6
12.9
8.9
6.8
8.0
5.5
4.2
4.5
3.1
2.4
2.4
1.6
1.2
300
19.4
13.5
10.3
15.2
10.6
8.1
9.5
6.6
5.0
5.3
3.7
2.8
2.8
2.0
1.5
This joint can resist the thrust in places where space is limited or where soil behind the fitting is unable to
provide sufficient support. This restriction method involves the proper locations of these special joints and
400
24.9
17.7
13.6
19.5
13.9
10.7
12.1
8.6
6.6
6.8
4.8
3.7
3.6
2.6
2.0
450
27.7
19.8
15.3
21.7
15.5
12.1
13.5
9.7
7.5
7.6
5.4
4.2
4.0
2.9
2.2
500
30.0
21.6
16.8
23.6
16.9
13.2
14.6
10.5
8.2
8.2
5.9
4.6
4.3
3.1
2.4
600
34.6
25.2
19.7
27.2
19.8
15.5
16.9
12.3
9.6
9.5
6.9
5.4
5.0
3.7
2.9
Xinxing can provide the ductile iron pipe with self-anchored joint as follows:
700
38.8
28.6
22.5
30.5
22.4
17.7
18.9
13.9
11.0
10.6
7.8
6.2
5.6
4.1
3.3
1) TF self-anchored joint ductile iron pipe (see Section 1.5 for details)
2) Xanchor self-anchored joint ductile iron pipe (see Section 1.6 for details)
Anchoring length of self-anchored pipe
Restrained length is to calculate how many pipes with self-anchored joints shall be needed along two sides
of the bend, so as to counteract hydraulic thrust force caused by the pressured liquid within the bend with
the frictional force between the pipe and the soil.
800
42.6
31.6
25.1
33.4
24.9
19.7
20.8
15.4
12.2
11.6
8.7
6.9
6.2
4.6
3.6
900
46.2
34.7
27.7
36.3
27.2
21.7
22.5
16.9
13.5
12.6
9.5
7.6
6.7
5.0
4.0
1000
49.6
37.6
30.1
39.0
29.5
23.7
24.2
18.3
14.7
13.6
10.3
8.2
7.2
5.4
4.4
1100
52.8
40.3
32.5
41.5
31.7
25.5
25.8
19.7
15.9
14.4
11.0
8.9
7.7
5.8
4.7
1200
55.7
42.9
34.8
43.7
33.7
27.3
27.2
20.9
17.0
15.2
11.7
9.5
8.1
6.2
5.0
1400
60.7
47.4
38.7
47.7
37.2
30.4
29.6
23.1
18.9
16.6
12.9
10.6
8.8
6.9
5.6
1600
65.8
52.0
42.9
51.7
40.9
33.7
32.1
25.4
21.0
18.0
14.2
11.7
9.5
7.5
6.2
1800
69.0
55.1
45.8
54.2
43.3
36.0
33.7
26.9
22.3
18.9
15.1
12.5
10.0
8.0
6.6
The anchoring length for bead and pipe end are as following:
Note: 1. The following factors shall be considered for the a nchoring length of the self-anchored pipe:
oring
anch
h
lengt
ancho
ring le
ngth
anchoring length
Terminal
finishing layer in the ordinary soil with an internal friction angle of 30 , test pressure of 10Bar, and safety factor of 1.2.
3 When the DI pipe has PE sleeve or its external coating is polyurethane, the data in the table can be multiplied by 1.9; if
more accurate data are needed, please contact us.
4. If data in the table is divided by 10 and then multiplied by the pressure value (unit: bar) you need, the result can be
obtained for the pressure required;
112
XINXING PIPES
113
Chapter V
Construction,
Installation and
Acceptance of
Ductile Iron Pipe
114
XINXING PIPES
115
Chapter V
Construction,
Installation and
Acceptance of
Ductile Iron Pipe
5.2.1 Preparation
5.2.2 Installation of ductile iron pipe with T-type joint
5.2.3 Connection of XT2-type Joint ductile iron pipe
5.2.4 Connection of ductile iron pipe with TF self-anchored joint
5.2.5 Connection of ductile iron pipe with Xanchor self-anchored joint
5.2.6 Installation of PE protective sleeve
5.2.7 Construction of XTJ jacking pipe
5.2.8 Construction under special conditions
5.3 Trench backfill143
5.4 Site Repairing of coating 144
5.5 Methods of circle calibration 144
5.6 Pipe cutting 145
5.7 Welding of self-anchored joint bead 146
5.8 Repairing the damaged pipeline 148
5.9 Pressure test and acceptance150
5.9.1 Provisions on pressure test
5.9.2 Water injection
5.9.3 Pressure test procedure
5.9.4 Eligibility criteria
116
XINXING PIPES
117
unit: mm
Nominal diameter DN
Trench width W
Nominal diameter DN
Trench width W
80
680
700
1300
(1) The excavated section of the trench shall meet the design requirements; the original subsoil at the
100
700
800
1400
trench bottom cant be disturbed. For mechanical excavation, 200 ~ 300mm soil layer shall be reserved at
150
750
900
1500
200
800
1000
1600
250
850
1100
1700
the trench bottom which will be excavated manually to the designed elevation and then leveled off;
(2)The trench bottom shall not be subject to water immersion or freezing, otherwise, it is necessary to use
300
900
1200
1800
350
950
1400
2000
(3) When the soil layer at the trench bottom is miscellaneous fill or corrosive soil, they shall be excavated
completely and then the foundation shall be treated according to the design requirements;
(4) Joint holes shall be reserved at each joint for the socket of the pipe, so as to ensure straightness of the
pipe and meet the requirement of installation.
400
1000
1500
2100
450
1050
1600
2200
500
1100
1800
2400
600
1200
2000
2600
Notes: (1) The W in above table refers to the clear width of a pipeline trench.
(5) For those influenced on the groundwater, the dewatering and drainage program for construction shall be
(2) If wood supports, baffles, braces and auxiliary means are used, the trench shall be widened to facilitate
shoring
without shoring
XINXING PIPES
119
(4) Cleaning the joint parts for the pipe spigot and socket
Clean the joint parts of the pipe spigot and socket before the pipe laying, especially for location to place
gasket, where dust, sand, stones and other substances are not allowed.
5.2.1 Preparation
When the gasket is put into the socket, impose radial force to keep it fully into the groove of socket, as
shown in Figure 5;
XINXING PIPES
Figure 3 DNDN800
Figure 4 DN
DN800
121
(2)Joint connection
While connecting, firstly align the socket and the spigot of two pipes, then slowly push the
spigot into the socket, and insert it between the two spigot lines, as shown in the Figure7.
Stop the installation immediately if too much resistance is found during inserting the ductile
iron pipe. Pull out the pipe and check location of the gasket, the socket and the spigot of the
pipe, identify the causes and handle them properly before re-installation.
Note: Mark the spigot line clearly before installation while installing the sawed ductile iron
pipe.
Figure 5
Different tools can be used to install in view of specifications of ductile iron pipes:
Simple tools, like crowbar can be used for the pipes below DN150. Hardwood must be
used to protect between the crowbar and the socket surface (see Fig. 8);
Tools like steel cable and guide chain can be used for installation of pipes above
DN200 (the contact between the steel cable or guide chain and pipes shall be protected by
a flexible materials , so as to avoid damage to the pipe body and both internal and external
Labricating
paste
coatings) (see Fig. 9). Please refer to Table 2 for the tonnage and quantity of guide chains for
installing ductile iron pipes of different specifications; an excavator can also be used for such
installation (Fig. 10), position between the pipe and bucket must be protected by hardwood ;
122
XINXING PIPES
123
Table 3 Insertion Depth of Spigot end for T-type Joint Ductile Iron Pipes (Recommended)
P-10
DN100~200
DN300~400
DN500~600
DN700~800
DN900~1000
DN1200~1400
2~3
DN1600~2000
10
2~3
Size
T-type
Joint
DN80
P-10
XT2-type
Joit
Size
T-type
Joint
75
82
DN450
DN100
78
84
DN125
80
DN150
85
DN200
90
DN250
95
DN300
100
DN350
DN400
P-10
XT2-type
Joint
Size
T-type
Joint
XT2-type
Joint
110
105
DN1400
230
235
DN500
110
107
DN1500
240
DN600
110
112
DN1600
250
255
90
DN700
140
137
DN1800
290
265
DN800
150
DN2000
309
280
DN900
165
DN2200
307
97
DN1000
175
DN2400
326
100
100
DN1100
190
DN2600
343
100
102
DN1200
205
157
95
147
(3)Installation check
Upon the completion of connection, the method shown in Figure 11 can be used to check the position of the
gasket :
Use a thin and narrow steel ruler to check the compression ratio of gasket at the four points around the
spigot with an angle of 90 between them. The steel ruler shall be inserted with the almost same depths at
four points, which can indicate a normal connection of joint.
The insertion depth at the spigot generally equals to the depth P of socket minus 10mm (see Table 3 for the
dimensions of the spigot insertion). In real installation, the first spigot line of one pipe shall all be covered by
the socket end of its adjoining pipe, and the second spigot line shall be exposed.
Figure 12
NO.
name
gland
Locking
Ring
Welded
Bead
spigot
Bolts with
hooked
head
gasket
Socket
124
XINXING PIPES
125
(2)Installation Steps
First, push gland 1 and locking ring 2 successively from the spigot 4 and pass
them through thrust welded bead 3, as shown in the figure 17. When the locking ring
completely crosses the welded bead, push it back so that the locking ring can fit with
the end face of the welded bead;
Insert spigot 4 into socket 7 of another pipe with gasket 6 installed (Please refer to
5.2.2 Installation of ductile iron pipe with T-joint for the specific connection).
Move the gland to the locking ring. Adjust the gap between gland 1 and the pipe
body to make it substantially evenly well-distributed, keep the end faces of gland 1
and socket 7 in parallel, make the internal conical surface of gland 1 to closely fit the
external conical surface of locking ring 2, then tighten hook bolt 5 to fix gland 1 with
socket 7 by tightening hook bolt 5. When tightening the bolt, take care to it is necessary
to carefully check and adjust so that the bevel eave tile slope of hook bolt 5 fits well
with the boss of the socket, and so that the gap between gland 1 and the face of the
socket end can be even almost even
126
XINXING PIPES
127
Install gasket
press the front stoppers between two rear stoppers, see Fig.
17;
Fig. 15;
the support ring, and insert the groove of stopper onto the
details;
128
XINXING PIPES
129
Note: if this method is applied to the DIP connected with bolted, a layer of PE protective
sleeve must be added at the pipe joints;
PE sleeve method refers to a kind of anti-corrosion method for the metal pipe free from corrosion within
the service period by using a complete PE pipe or sheet to wrap up the buried pipeline before the pipeline
installation, so as to separate the metal pipes from their corrosive soil environment.
Step 1: use steel cable or sling to lift the pipe almost at the middle of the pipe and keep
There have been over 50 years to use PE sleeve to protect ductile iron pipe against corrosion. It have
the entire pipe off the ground; cover the already-cut polyethylene sleeve (1m longer than
been proved by extensive laboratory research and practical engineering cases that this method is still the
the pipe) on the pipe between the spigot and steel cable from the end of pipe spigot;
most cost-effective method for anti-corrosion, suitable for buried ductile iron pipelines in most corrosive
environments .
Note: The harshly corrosive environments with high-density stray currents and those specified in Annex A of
AWWA C105 are exception.
Performance requirement of PE protective sleeve
The material and performance of PE protective sleeve shall meet the requirements of ISO8180 or AWWA
C105
Features of PE protective sleeve
A. Easy to construct, and highly cost-effective anti-corrosion;
Step 2: lower the pipe into the trench and connect the pipe which has been installed before.
Step3:slip the steel cable, lift the socket of the pipe, then spread the PE cover over
the entire barrel of the pipe;
130
XINXING PIPES
131
Step 4: pull back the surplus polyethylene sleeve at the side of the joint socket, wrap
Step 7: secure the fold of the PE sleeve along the axial direction of the pipe barrel
it onto the pipes at the joint and use the adhesive tape to secure it in place;
Step 8: repair all small rips, tears or other tube damage with adhesive tape or PE
tape;
Step 5: straighten the surplus PE sleeve at the end of the spigot, spread it and wrap
it on the joint. Then bunch the end of the PE pipe onto the ductile iron pipe;
Step 9: carefully backfill the pipe according to AWWA C600 for backfill procedure.
Slowly backfill to prevent damage to the PE sleeve during backfilling;
132
XINXING PIPES
Nominal diameter
DN
100
200
300
500
800
1000
1200
1500
1800
2000
Folded width of PE
tube
580
950
1300
2000
3050
3720
4400
5470
6550
7200
133
In order to prevent large hard objects from damaging PE sleeve during backfilling, the grassy meadow
can be put on top of the pipe or sand, loam or soil without stones and other hard objects can be used for
backfilling. It is preferential to forbid from walking on the completed pipes, so as to avoid damage to the PE
sleeve.
For fittings such as tees and crosses, as required by the pipe shapes, it is necessary to cut off the PE
sleeve or directly wrap PE sheet arround the entire pipe and then stick the joints of PE sleeve with the
adhesive tape.
134
XINXING PIPES
135
back wall
groundwater level, ground and underground buildings structures and facilities nearby, and so on, and
determined after the technical and economic comparison is conducted. In case no relevant experience is
available, Table 5 can be referred to.
Table 5 Reference for Selection of Push Bench
Open push bench
Stratum
Mechanical
Cemented soil, strong
weathered rock
Stable soil
Loose soil
no
groundwater
Extrusion
Manual
excavation
Earth
pressure
balance
Slurry
balance
Pressure
balance
Sludge fd 30kpa
Stratum below
Silty soil
groundwater
Including obstacles
Minimum internal length of the working well can be calculated with the following formula
La+b+c+d+d+e
Where, Lmin net internal length of the working well (m)
B=D+(2.0~4.0)
(1)General regulations
a.To facilitate drainage, excavation and transportation, the working well and receiving well shall be located
close to the power and water, far away from the residential areas and high-voltage lines, and avoiding
Min net internal width of receiving well shall not be more than min net width of the working well; min net
internal length of the receiving well shall be sufficient for removal of the push bench in the well and hoisting
b.The working well and receiving well can be structured with steel sheet pile, open caisson, underground
c.The working well and receiving well can be constructed in the circular, rectangular or polygonal form. The
Basic requirements
pipeline-crossing intermediate well and large-depth working well can be circular or polygonal.
Sufficient strength
Sufficient rigidity
Flat surface of back wall
136
XINXING PIPES
137
Homogeneous material
Coefficient of passive
earth pressure KP
Coefficient of active
earth pressure KA
Assumed that the jacking of the main jack is evenly imposed on the soil mass behind the working pit through
Soft soil
10
1.42
0.70
2.03
the back wall, the reaction force R of the back wall shall be 1.2 ~ 1.6 times of total jacking force F0, so as
Clay
20
2.04
0.49
4.16
to ensure the safety of the back wall during jacking, the reaction force R can be calculated with the following
Sand clay
25
2.46
0.41
6.00
Silty soil
27
2.66
0.38
7.00
Sandy soil
30
3.00
0.33
9.09
Gravel soil
35
3.69
0.27
13.67
formula:
2
R =aB H
KP
2
+2cH
KP+hHKP
KP
KA
Hoisting machinery
Pipe jacking requires equipment for vertical hoisting and transportation. Overhead crane (i.e. portal crane)
or rotating jib crane (such as truck crane, crawler cranes) can be used under common circumstances, and
h height of soil mass from the ground to top of back wall (m)
XINXING PIPES
139
Table 7 Calculation Formula for Head Resistance of the Push Bench (NF)
End face of push
bench
Cutting edge
Mechanical
Manual excavating
NF=(Dg-t)tR
Socket mouth
Push-in
NF=Dg (1-e)R/4
e-opening rate
Grid
Push-in
NF=Dg aR/4
NF=Dg (aR+Pn)/4
NF=Dg HF/4
a-grid-sectional parameters
Preferably a = 0.6~1.0
Pnair pressure(kN/m2)
HFoverburden thickness(m)
clamps
unrestrained joint
a. Continuously operate with the principle of jacking following excavating, jacking while excavating
followed, any suspension shall be avoided , otherwise it will increase the resistance and jacking difficulty;
b. The quality of whole jacking pipeline is related to the jacking direction and elevation of the first section of
For the spigot and socket pipes laid on the ground, its suggested to provide one support for each pipe,
pipe. So it is necessary to frequently measure and check to timely correct the deviation, if any;
such as concrete stand. The support shall be put behind the socket of each pipe.
c. If the stroke of jacking cylinder is less than the length of a single pipe, then the piston can be withdrawn
Fix the pipe onto the support with steel strip. Insert a rubber pad to increase friction between the steel
after the cylinder piston is stretched out for one working stroke, now a thrust ring can be added between the
strip and pipe. Thus, the axial stretch of the pipe resulting from temperature change can be absorbed at
each joint.
d. Once the earthwork in front of the pipe collapses or the pressure gauge hand of the pump suddenly
swings substantially during jacking, the jacking shall be stopped immediately and proceed until the causes
The fittings that are likely to produce thrust due to the internal pressure, such as the elbows and Tees, shall
e. The maximum working jacking force of the jacking cylinder shall not exceed the allowable jacking thrust.
Fixing clamp
rubber lining
namely, injecting slurry around the pipe wall to form a lubricating sleeve so as to reduce resistance when
jacking.
Figure 22 Fixing clip put behind the socket
140
XINXING PIPES
141
clamps
joints
(1) Backfill the trench in time when the pipeline construction is completed and passed inspection.
For pressure pipes, both sides and top of pipe, except for the joints, shall be backfilled for no less
than0.5m high before the water pressure test; The rest parts shall be timely backfilled when it is qualified
Figure 23 Pipe laying on level ground
(2) The following requirements shall be met during backfill of the trench:
There are three main installation methods for pipes going through the ditches,
Clean up brick, stone, wood blocks and other debris in the trench;
No water shall exist in the trench, and dont backfill with water;
Check whether there is any damage or deformation on the pipe before backfilling. If any, it shall be
repaired or replaced;
The range of the effective support angle at the pipe base shall be filled and compacted by granular sand,
keeping it contact closely with the pipe wall;
(a)
Simultaneously backfill and compact from both sides of pipeline; take measures against pipeline floating
and displacement when backfilling below the centre of pipe;
Manual tamp shall be conducted from the base of pipe bottom to the level of 500mm above the pipe
top during the trench backfilling; The locations beyond 500mm above the pipe top shall be compacted with
(b)
When backfilling in the freezing period, frozen soil can be evenly mixed at the range over 500mm above
the pipe top, but its amount can not go beyond 15% of the total volume of the filling;
(5)The loose laying depth of each layer of backfill shall be selected on the basis of the compacting appliance
adopted as specified in Table 8.
L
Table 8 Loose Laying Depth of Every Layer of Backfill
43
(c)
Typical surport
Compacting appliance
200
200~250
Roller
200~300
Vibratory roller
400
142
XINXING PIPES
143
When the pipe is laid under the roadway, the road shall be paved immediately after the laying; when the
pipe is located in the soft soil layer and low-lying, swamp, or high groundwater level sections, the medium
and coarse sand shall be firstly used to backfill and compact the auxiliary corners of pipe base, and then
1) When the spigot of DIP is damaged due to improper handling, affecting installation, this part shall be cut
medium and coarse sand shall be used to backfill layer by layer till 500mm above the pipe top.
off;
When the ductile iron pipe is backfilled to the design elevation, the deformation rate of the pipe shall be
2) In event that the pipe length shall be determined in the field for the sake of installing pipe fittings during
measured and recorded within 12 ~ 24h, which shall meet the design requirements; if there is no design
For the DIP with a diameter DN300, cutting can be conducted at 2/3 of the pipe barrel starting from the
The covering depth above the pipe top shall meet the design requirements; please refer to Appendix B of
For the DIP with a diameter > DN300, the manufacturers generally provide cuttable pipes with a certain
percentage.
3) Pipe-cutting tools: abrasive cutter or electric metal-saw pipe cutter can be adopted. The method of
oxygen cutting is forbidden, since over-high cutting temperature will affect performance of ductile iron
material.
Any damage on the internal and external coatings during hoisting, transportation and installation must be
4) For T-joint and XT2-joint DIP, the newly-cut end shall be rounded and chamfered so as to avoid the
repaired. Refer to 1.11 Coating Repairment for detailed methods of site repair.
and handling. For the pipes below DN400, the part with oval
deformation shall be cut off, while for the pipes above DN500,
Y
Surport
Figure 26 toothless abrasive cutter
Jack
(1) The size and shape of block arc at the lower and upper arc
of the jack shall be made respectively in accordance with the
different specifications of pipes to be calibrated.
(2) Reference data for jacking amount of circle calibration: the
144
DN(mm)
DE(mm)
X(mm)
Y(mm)
DN(mm)
DE(mm)
X(mm)
Y(mm)
80
98
600
635
100
118
700
738
15
125
144
800
842
15
150
170
900
945
15
200
222
1000
1048
15
250
274
1100
1152
15
300
326
1200
1255
15
350
378
1400
1462
20
400
429
1500
1565
21
450
480
1600
1668
21
500
532
1800
1875
27
XINXING PIPES
145
Under guidance of the professional welding engineer, the ductile iron pipe can be welded in the field.
DN
PFA(bar)
DN
PFA1(bar)
116
4.5
116
4.5
148
158
DN80
82
DN500
Welding tools
DN100
85
DN600
Main welding tools cover welder, grinder, nickel-based electrode and copperplate positioning device, etc.;
DN150
89
DN700
Welding procedure
DN200
95
Firstly, carefully clean the outer surface of DIP with abrasion wheel, as shown in Fig. 28. The polishing
DN250
105
DN300
Fix the copper plate positioning device onto the external wall of DIP according to the sizes shown in
DN350
Table11. The copper guide ring must be close to the pipe wall. If necessary, tap it with a hammer, as shown
DN400
in Fig. 29;
1 The table above shows parameters of welded bead for TF-seif-anchored joint DIP of K9 class. If the designed
pressure is higher than the PFA value in the table above, the welded bead parameters and wall thickness of pipe shall also
be increased correspondingly. Please contact us for the specific parameters.
Layered when welding to ensure the welding quality, as shown in Fig. 30;
30
25
25
DN800
DN900
23
173
105
DN1000
22
183
105
DN1100
21
198
105
DN1200
20
213
Remove the copper guide ring, polish the weld ring to the dimensions shown in Figure 33 and Table11.
Coating repair
ductile iron pipe Copper guide
welded bead
Clean up the welding area. The cleaned surface is required to be smooth and clean, oil- and dust-free.
Please refer to Section 1.11 Coating Repairment for the detailed repair methods of the internal and
external coatings.
a
c
146
XINXING PIPES
147
(4)Pipe replacement
As shown in Fig33. cut a section of same-size double-spigot short pipe with a length of(L-8) and put it at the
If the ductile iron pipe being used is damaged locally and leaks, it can be repaired with K-type collar repair
(5)Connection of collar
Move axially two K-type collars to the newly-inserted pipe section and connect them according to the
Dig out the damaged part of the pipeline, cut off the damaged pipe section after confirming the damaged
requirements in 4.2.4 Installation of ductile iron pipe with K-joint. The completed connection is shown in
breakage
(6)Coating repair
Prepare a section of double-spigot pipe of the same specification and two sets of K-type collar assembly;
Repair the coating damaged during cuttings according to the coating-repair requirements provided by the
manufacturer before installing all the parts. Please refer to 1.11 Coating Repairment for detailed repair
Connect two connection ends of K-type collar to two ends of pipe to be repaired, so that the spigot of
methods;
original pipe can be inserted into max installation depth of K-type collar, see Fig. 32 for details;
K-type collar
K-type collar
L
double-spigot short pipe
Original pipeline
148
XINXING PIPES
149
keep the test pressure by a pump at least: one hour for DN 600; three hours for 600 <DN1400; and
six hours for DN> 1400. Meanwhile the water amount for maintaining the pressure shall be measured.
A newly-installed water supply and drainage pipeline shall undergo hydrostatic pressure test before being
put into usage. The test pressure and acceptance criteria can refer to ISO10802.
pressure, average hydraulic pressure exerted on the test area, if elevations of every location on the entire
pipeline are quite different, then the loss criteria shall be calculated on the basis of the weighted average
Unless otherwise stated for pressure pipelines, length of pressure test section shall not be beyond 1,000 ~
pressures). The pressure test is regarded passed when water loss from DN100 pipeline per kilometer under
1,500m.
Test pressure
Non-pressure pipelines: water loss shall not exceed 0.1 l/km (pipeline length)/mm (nominal size). However,
1)The test pressure at the lowest point of test area shall not be less than the limit values specified in a) or b)
when the prescribed test pressure exceeds 1 bar, the eligibility criteria of pressure pipeline will be applicable.
(whichever is larger).
a) When the working pressure is less than or equal to 10 bar: test value is 1.5 times of the working pressure;
when the working pressure is greater than 10 bar: test value is the working pressure plus 5 bar.
b) Maximum working pressure
2)The test pressure at the highest point of test area shall not be less than the working pressure at the same
point.
3) The test pressure shall not exceed:
a) Max test pressure applicable to pipes, pipe fittings, flanges and accessories specified in the standard;
b) Design pressure of clamp or anchor device.
150
XINXING PIPES
151
Chapter VI
Xinxing Ductile
Iron Fittings and
Accesseries
152
XINXING PIPES
153
Chapter VI
Xinxing Ductile
Iron Fittings and
Accesseries
154
XINXING PIPES
155
(42) Flanges
(18) Double-Flanged Bends with Duckfoot 90 (Refer to Figure 18 and Table 18)
(23) Double-Socket Tees with Flanged Branch (Refer to Figure 23 and Table 23)
(26) Socket-Spigot Tees with Socket Branch (Refer to Figure 26 and Table 26)
(48) Bolts for Flange Connection (Refer to Figure 48 and Table 57)
(27) Socket-Spigot Tees with Flange Branch (Refer to Figure 27 and Table 27)
(49) Bolts for K-type joint Connection (Refer to Figure 49 and Table 58)
(28) Double-Socket Level Invert Tees with Flanged Branch (Refer to Figure 28 and Table 28)
(29) All Socket Level Invert Tees (Refer to Figure 29 and Table 29)
(30) Socket Spigot Level Invert Tees with Flanged Branch (Refer to Figure 30 and Table 30)
(31) All Socket Eccentric Tees 45 (Refer to Figure 31 and Table 31)
(32) All Flanged Eccentric Tees 45 (Refer to Figure 32 and Table 32)
(33) All Socket Crosses (Refer to Figure 33 and Table 33)
(34) All Flanged Crosses (Refer to Figure 34 and Table 34)
(35)Socket Spigot Crosses with Double Socket (Refer to Figure 35 and Table 35)
156
XINXING PIPES
157
158
DN
Figure No.
Table No.
31
80~600
31
31
Flanged spigots
80~2000
32
80~600
32
32
Socket Spigots
80~1800
33
80~600
33
33
Collars
80~2000
34
80~600
34
34
Flanged Sockets
80~2000
35
80~600
35
35
80~2000
Double-Socket Bends 90
80~1400
36
80~1800
36
36
Double-Socket Bends 45
80~2000
37
80~1800
37
37
80~2000
38
Flexible Couplings
80~1600
38
38
Double-Socket Bends11.25
80~2000
39
Flange Adaptors
80~1600
39
39
10
Socket-Spigot Bends 90
80~1400
10
10
40
Dismantling Joints
80~1600
40
40
11
Socket-Spigot Bends 45
80~2000
11
11
41
Flanged Bellmouthes
80~2600
41
41
12
80~2000
12
12
42
Flanges
80~2000
42
4243
4445
13
80~2000
13
13
43
Welded-on Flanges
40~2000
43
464748
14
Double-Flanged Bends 90
80~1400
14
14
44
80~2000
44
49
15
Double-Flanged Bends 45
80~2000
15
15
45
Blank Flanges
80~2000
45
505152
16
80~2000
16
16
46
Reducing Flanges
80~800
46
535455
17
80~2000
17
17
47
80~1400
47
56
18
80~1000
18
18
48
80~2000
48
57
19
Double-Socket Tapers
80~2000
19
19
49
1600~2600
49
58
20
Double-Flanged Tapers
80~2000
20
20
21
Double-Socket offsets
100~300
21
21
22
Socket-Spigot Offsets
100~300
22
22
23
100~2000
23
23
24
80~2000
24
24
25
80~2000
25
25
26
80~2000
26
26
27
80~2000
27
27
28
80~2000
28
28
29
100~2000
29
29
30
80~2000
30
30
No.
Product Name
XINXING PIPES
Symbol
159
Unit:mm
DN
DN
80
350
700
14.4
600
100
7.2
360
800
15.6
600
125
7.5
370
900
16.8
600
150
7.8
380
1000
18
600
200
8.4
400
1100
19.2
600
250
420
1200
20.4
600
300
9.6
440
1400
22.8
710
350
10.2
460
1500
24
750
400
10.8
480
1600
25.2
780
450
11.4
500
1800
27.6
850
500
12
520
2000
30
920
600
13.2
560
160
XINXING PIPES
Unit:mm
Unit:mm
DN
DN
80
255
600
13.2
425
100
7.2
255
700
14.4
460
125
7.5
265
800
15.6
475
150
7.8
270
900
16.8
500
200
8.4
285
1000
18
515
250
300
1100
19.2
540
300
9.6
315
1200
20.4
565
350
10.2
335
1400
22.8
620
400
10.8
355
1600
25.2
650
450
11.4
365
1800
27.6
700
500
12
385
Figure 3 Collars
Table 3 Technical Parameters for Collars
Unit:mm
DN
DN
80
160
700
14.4
220
100
7.2
160
800
15.6
230
125
7.5
165
900
16.8
240
150
7.8
165
1000
18
250
200
8.4
170
1100
19.2
260
250
175
1200
20.4
270
300
9.6
180
1400
22.8
310
350
10.2
185
1500
24
350
400
10.8
190
1600
25.2
360
450
11.4
195
1800
27.6
380
500
12
200
2000
30
400
600
13.2
210
161
162
Unit:mm
Unit:mm
DN
DN
DN
DE
DN
DE
80
130
700
14.4
190
80
98
700
738
14.4
100
7.2
130
800
15.6
200
100
118
7.2
800
842
15.6
125
7.5
135
900
16.8
210
125
144
7.5
900
945
16.8
150
7.8
135
1000
18
220
150
170
7.8
1000
1048
18
200
8.4
140
1100
19.2
230
200
222
8.4
1100
1152
19.2
250
145
1200
20.4
240
250
274
1200
1255
20.4
300
9.6
150
1400
22.8
310
300
326
9.6
1400
1462
22.8
350
10.2
155
1500
24
330
350
378
10.2
1500
1565
24
400
10.8
160
1600
25.2
330
400
429
10.8
1600
1668
25.2
450
11.4
165
1800
27.6
350
450
480
11.4
1800
1875
27.6
500
12
170
2000
30
370
500
532
12
2000
2082
30
600
13.2
180
600
635
13.2
XINXING PIPES
163
164
Unit:mm
Unit:mm
DN
DN
DN
DN
80
100
500
12
520
80
50
700
14.4
330
100
7.2
110
600
13.2
620
100
7.2
60
800
15.6
370
125
7.5
145
700
14.4
720
125
7.5
75
900
16.8
415
150
7.8
170
800
15.6
820
150
7.8
85
1000
18
460
200
8.4
220
900
16.8
920
200
8.4
110
1100
19.2
505
250
270
1000
18
1020
250
130
1200
20.4
550
300
9.6
320
1100
19.2
1120
300
9.6
150
1400
22.8
515
350
10.2
370
1200
20.4
1220
350
10.2
175
1500
24
540
400
10.8
420
1400
22.8
1220
400
10.8
195
1600
25.2
565
450
11.4
470
450
11.4
220
1800
27.6
610
500
12
240
2000
30
660
600
13.2
285
XINXING PIPES
165
166
Unit:mm
Unit:mm
DN
DN
DN
DN
80
40
700
14.4
175
80
30
700
14.4
95
100
7.2
40
800
15.6
195
100
7.2
30
800
15.6
110
125
7.5
50
900
16.8
220
125
7.5
35
900
16.8
120
150
7.8
55
1000
18
240
150
7.8
35
1000
18
130
200
8.4
65
1100
19.2
260
200
8.4
40
1100
19.2
140
250
75
1200
20.4
285
250
50
1200
20.4
150
300
9.6
85
1400
22.8
260
300
9.6
55
1400
22.8
130
350
10.2
95
1500
24
270
350
10.2
60
1500
24
140
400
10.8
110
1600
25.2
280
400
10.8
65
1600
25.2
140
450
11.4
120
1800
27.6
305
450
11.4
70
1800
27.6
155
500
12
130
2000
30
330
500
12
75
2000
30
165
600
13.2
150
600
13.2
85
XINXING PIPES
167
168
Unit:mm
Unit:mm
DN
DN
DN
DN
80
100
280
450
11.4
470
670
80
50
235
700
14.4
330
580
100
7.2
110
300
500
12
520
720
100
7.2
60
245
800
15.6
370
620
125
7.5
145
325
600
13.2
620
820
125
7.5
75
255
900
16.8
415
665
150
7.8
170
350
700
14.4
720
900
150
7.8
85
265
1000
18
460
760
200
8.4
220
400
800
15.6
820
1000
200
8.4
110
290
1100
19.2
505
805
250
270
450
900
16.8
920
1100
250
130
310
1200
20.4
550
850
300
9.6
320
500
1000
18
1020
1200
300
9.6
150
330
1400
22.8
515
815
350
10.2
370
550
1200
20.4
1220
1400
350
10.2
175
355
1500
24
540
840
400
10.8
420
600
1400
22.8
1220
1600
400
10.8
195
375
1600
25.2
565
925
450
11.4
220
420
1800
27.6
610
970
500
12
240
440
2000
30
660
1060
600
13.2
285
485
XINXING PIPES
169
170
Unit:mm
Unit:mm
DN
DN
DN
DN
80
40
220
700
14.4
175
425
80
30
210
700
14.4
95
345
100
7.2
40
220
800
15.6
195
445
100
7.2
30
210
800
15.6
110
360
125
7.5
50
230
900
16.8
220
470
125
7.5
35
215
900
16.8
120
370
150
7.8
55
235
1000
18
240
540
150
7.8
35
215
1000
18
130
430
200
8.4
65
245
1100
19.2
260
560
200
8.4
40
220
1100
19.2
140
440
250
75
255
1200
20.4
285
585
250
50
230
1200
20.4
150
450
300
9.6
85
265
1400
22.8
260
560
300
9.6
55
235
1400
22.8
130
430
350
10.2
95
275
1500
24
270
570
350
10.2
60
240
1500
24
140
440
400
10.8
110
290
1600
25.2
280
640
400
10.8
65
245
1600
25.2
140
500
450
11.4
120
320
1800
27.6
305
665
450
11.4
70
270
1800
27.6
155
515
500
12
130
330
2000
30
330
730
500
12
75
275
2000
30
165
565
600
13.2
150
350
600
13.2
85
285
XINXING PIPES
171
172
Unit:mm
Unit:mm
DN
DN
DN
DN
80
165
450
11.4
550
80
130
700
14.4
480
100
7.2
180
500
12
600
100
7.2
140
800
15.6
530
125
7.5
200
600
13.2
700
125
7.5
150
900
16.8
580
150
7.8
220
700
14.4
800
150
7.8
160
1000
18
630
200
8.4
260
800
15.6
900
200
8.4
180
1100
19.2
695
250
350
900
16.8
1000
250
350
1200
20.4
750
300
9.6
400
1000
18
1100
300
9.6
400
1400
22.8
775
350
10.2
450
1200
20.4
1300
350
10.2
300
1500
24
810
400
10.8
500
1400
22.8
1470
400
10.8
325
1600
25.2
845
450
11.4
350
1800
27.6
910
500
12
375
2000
30
980
600
13.2
425
XINXING PIPES
173
174
Unit:mm
Unit:mm
DN
DN
DN
DN
80
125
600
13.2
405
80
125
600
13.2
405
100
7.2
135
700
14.4
300
100
7.2
135
700
14.4
205
125
7.5
150
800
15.6
330
125
7.5
80
800
15.6
230
150
7.8
155
900
16.8
360
150
7.8
155
900
16.8
245
200
8.4
170
1000
18
390
200
8.4
170
1000
18
265
250
340
1100
19.2
420
250
340
1100
19.2
320
300
9.6
390
1200
20.4
450
300
9.6
390
1200
20.4
360
350
10.2
290
1400
22.8
460
350
10.2
290
1400
22.8
380
400
10.8
310
1600
25.2
470
400
10.8
310
1600
25.2
400
450
11.4
335
1800
27.6
480
450
11.4
335
1800
27.6
410
500
12
360
2000
30
520
500
12
360
2000
30
415
XINXING PIPES
175
Unit:mm
DN
DN
DN
e1
dn
e2
80
165
110
180
400
10.8
500
320
500
100
7.2
80
100
7.2
180
125
200
450
11.4
550
355
550
7.5
200
140
225
500
12
600
385
600
7.8
80
125
150
150
7.8
220
160
250
600
13.2
700
450
700
200
8.4
260
190
300
700
14.4
800
515
800
250
350
225
350
800
15.6
900
580
300
9.6
400
255
400
900
16.8
1000
350
10.2
450
290
450
1000
18
1100
dn
e2
90
200
8.4
1080
190
250
980
100
7.2
150
300
9.6
880
80
290
350
10.2
780
100
7.2
250
400
10.8
680
900
150
7.8
150
450
11.4
580
645
1000
80
390
500
12
480
710
1100
100
7.2
330
600
13.2
280
150
7.8
250
400
10.8
880
200
8.4
150
450
11.4
780
80
490
500
12
680
100
7.2
430
600
13.2
480
150
7.8
350
700
14.4
280
200
8.4
250
400
10.8
1080
250
150
450
11.4
980
80
600
500
12
880
100
7.2
560
600
13.2
680
150
7.8
460
700
14.4
480
200
8.4
360
800
15.6
280
200
250
300
350
176
XINXING PIPES
8.4
9.6
10.2
DN
700
800
900
e1
Unit:mm
14.4
15.6
16.8
177
350
400
450
500
600
102
10.8
11.4
12
13.2
250
260
300
9.6
160
80
700
100
7.2
150
600
13.2
880
700
14.4
680
800
15.6
480
660
900
16.8
280
7.8
560
600
13.2
1080
200
8.4
460
700
14.4
880
250
360
800
15.6
680
300
9.6
260
900
16.8
480
350
10.2
160
1000
18
280
80
800
600
13.2
1280
100
7.2
760
700
14.4
1080
150
7.8
660
800
15.6
880
200
8.4
560
900
16.8
680
250
460
1000
18
480
300
9.6
360
1100
19.2
280
350
10.2
260
600
13.2
960
400
10.8
160
700
14.4
860
80
900
800
15.6
760
100
7.2
860
900
16.8
660
150
7.8
760
1000
18
560
200
8.4
660
1100
19.2
460
DN
e1
dn
e2
250
560
1200
20.4
360
100
7.2
80
300
9.6
460
800
15.6
960
150
7.8
80
350
10.2
360
900
16.8
860
400
10.8
260
1000
18
760
450
11.4
160
1200
20.4
560
80
1100
1400
22.8
100
7.2
1060
1000
150
7.8
960
200
8.4
860
250
300
1000
1100
1200
1400
18
19.2
20.4
22.8
dn
e2
200
250
9.0
1050
300
300
9.6
1000
100
7.2
280
350
10.2
900
80
600
400
10.8
800
100
7.2
600
450
11.4
750
360
150
7.8
300
500
12
700
18
960
80
650
600
13.2
600
1200
20.4
760
100
7.2
600
400
10.8
1030
1400
22.8
560
150
7.8
600
450
11.4
900
760
1600
25.2
360
200
8.4
300
500
12.0
800
9.6
660
1000
18
1160
80
700
600
13.2
700
350
10.2
560
1200
20.4
960
100
7.2
700
700
14.4
600
400
10.8
460
1400
22.8
760
150
7.8
650
400
10.8
1100
450
11.4
360
1600
25.2
560
200
8.4
600
450
11.4
1050
500
12
260
1800
27.6
360
250
300
500
12
1000
80
750
600
13.2
800
1600
1800
2000
25.2
27.6
30
200
250
300
350
178
XINXING PIPES
8.4
9.6
10.2
DN
700
800
900
e1
Unit:mm
14.4
15.6
16.8
179
350
400
450
500
600
180
XINXING PIPES
10.2
10.8
11.4
12
13.2
100
7.2
750
700
14.4
700
150
7.8
700
800
15.6
600
200
8.4
650
600
13.2
1000
250
9.0
600
700
14.4
800
300
9.6
300
800
15.6
700
80
800
900
16.8
600
100
7.2
800
600
13.2
1100
150
7.8
750
700
14.4
1000
200
8.1
700
800
15.6
800
250
9.0
650
900
16.8
700
300
9.6
600
1000
18
600
350
10.2
300
600
13.2
1150
80
900
700
14.4
1100
100
7.2
900
800
15.6
1000
150
7.8
800
900
16.8
800
200
8.4
750
1000
18
700
250
9.0
700
1100
19.2
600
300
9.6
650
600
13.2
860
350
10.2
600
700
14.4
850
400
10.8
300
800
15.6
950
80
950
900
16.8
1100
100
7.2
950
1000
18
1000
150
7.8
900
1100
19.2
800
200
8.4
800
1200
20.4
700
250
9.0
750
1400
22.8
600
300
9.6
700
1000
18
1650
350
10.2
650
1100
19.2
1465
400
10.8
600
1200
20.4
1000
450
11.4
300
1400
22.8
910
80
1050
1000
18
1760
100
7.2
1050
1200
20.4
1710
150
7.8
1000
1400
22.8
1340
200
8.4
950
1500
24
1550
250
9.0
900
1600
25.2
970
300
9.6
800
1000
18
2160
350
10.2
750
1200
20.4
2140
900
1000
1100
1200
1400
1500
1600
1800
2000
16.8
18
19.2
20.4
22.8
24
25.2
27.6
30
600
700
13.2
14.4
400
10.8
700
450
11.4
650
500
12
600
200
8.4
1100
200
30
1400
22.8
1770
1500
24
1585
1600
25.2
1400
1800
27.2
1030
Unit:mm
DN
100
7.2
475
200
150
7.8
625
250
200
8.4
655
300
250
665
300
300
9.6
670
300
181
(23)Double-Socket Tees with Flanged Branch (Refer to Figure 23 and Table 23)
Unit:mm
Lu
100
7.2
470
150
DN
dn
e1
150
7.8
475
150
80
8.1
170
80
8.1
200
8.4
600
200
80
700
250
8.4
170
250
100
190
300
9.6
800
300
150
200
XINXING PIPES
Body
DN
125
182
Branch
8.7
9.1
9.8
Unit:mm
dn
e1
165
590
400
12.6
675
8.1
175
640
450
13.3
665
100
8.4
180
690
500
14
670
170
80
8.1
190
800
600
15.4
685
195
100
8.4
195
920
700
16.8
700
225
125
8.7
200
1040
800
18.2
715
170
80
8.1
205
1170
900
19.6
750
195
100
8.4
210
240
80
8.1
670
230
125
8.7
215
260
100
8.4
670
255
150
9.1
220
290
125
8.7
675
175
80
8.1
235
310
150
9.1
680
200
100
8.4
240
360
200
9.8
705
235
125
8.7
240
420
250
10.5
705
255
150
9.1
250
480
300
11.2
710
315
200
9.8
260
530
350
11.9
720
DN
900
1000
Branch
19.6
21
183
250
300
350
400
450
184
XINXING PIPES
10.5
11.2
11.9
12.6
13.3
180
80
8.1
265
595
400
12.6
735
200
100
8.4
270
640
450
13.3
725
230
125
8.7
275
690
500
14
260
150
9.1
280
810
600
315
200
9.8
290
930
375
250
10.5
300
180
80
8.1
205
100
230
480
350
11.9
430
940
700
16.8
885
560
400
12.6
450
1070
800
18.2
915
730
620
450
13.3
460
1190
900
19.6
920
15.4
745
190
80
8.1
400
1300
1000
21
945
700
16.8
760
215
100
8.4
420
1520
1200
23.8
955
1040
800
18.2
775
240
125
8.7
420
340
80
8.1
870
295
1160
900
19.6
790
280
150
9.1
420
420
100
8.4
875
8.4
300
1290
1000
21
825
330
200
9.8
440
450
125
8.7
880
125
8.7
300
240
80
8.1
730
380
250
10.5
440
480
150
9.1
880
260
150
9.1
310
260
100
8.4
730
440
300
11.2
440
540
200
9.8
890
320
200
9.8
320
290
125
8.7
735
490
350
11.9
450
560
250
10.5
895
380
250
10.5
330
310
150
9.1
740
565
400
12.6
480
650
300
11.2
905
435
300
11.2
340
360
200
9.8
745
600
450
13.3
480
710
350
11.9
910
185
80
8.1
325
420
250
10.5
755
680
500
14
500
770
400
12.6
920
205
100
8.4
330
480
300
11.2
760
195
80
8.1
460
830
450
13.3
925
230
125
8.7
330
530
350
11.9
770
200
100
8.4
460
880
500
14
935
270
150
9.1
340
600
400
12.6
795
240
125
8.7
465
1030
600
15.4
980
325
200
9.8
350
650
450
13.3
795
260
150
9.1
470
1120
700
16.8
990
385
250
10.5
360
700
500
14
795
340
200
9.8
500
1260
800
18.2
1010
420
300
11.2
370
830
600
15.4
825
380
250
10.5
500
1350
900
19.6
1020
495
350
11.9
380
940
700
16.8
830
430
300
11.2
500
1495
1000
21
1040
185
80
8.1
355
1050
800
18.2
835
490
350
11.9
510
1580
1100
22.4
1045
210
100
8.4
360
1170
900
19.6
850
570
400
12.6
540
1700
1200
23.8
1050
230
125
8.7
360
1280
1000
21
870
610
450
13.3
540
1930
1400
26.6
1070
270
150
9.1
370
1390
1100
22.4
880
670
500
14
540
580
200
9.8
1030
325
200
9.8
380
240
80
8.1
790
800
600
15.4
580
635
250
10.5
1040
385
250
10.5
390
260
100
8.4
790
210
80
8.1
490
695
300
11.2
1045
440
300
11.2
400
290
125
8.7
795
230
100
8.4
490
810
400
12.6
1060
480
350
11.9
410
310
150
9.1
800
250
125
8.7
495
925
500
14
1075
560
400
12.6
420
360
200
9.8
805
280
150
9.1
500
1040
600
15.4
1090
190
80
8.1
370
420
250
10.5
815
345
200
9.8
525
1275
800
18.2
1120
215
100
8.4
390
480
300
11.2
820
390
250
10.5
525
1505
1000
21
1150
230
125
8.7
390
530
350
11.9
830
440
300
11.2
525
1740
1200
23.8
1180
270
150
9.1
400
590
400
12.6
835
500
350
11.9
530
1970
1400
26.6
1210
330
200
9.8
410
650
450
13.3
845
575
400
12.6
555
2200
1600
29.4
1240
390
250
10.5
420
710
500
14
850
610
450
13.3
545
595
200
9.8
1150
445
300
11.2
430
840
600
15.4
885
680
500
14
550
650
250
10.5
1150
1000
1100
1200
21
22.4
23.8
450
500
600
700
13.3
14
15.4
16.8
1200
1400
1600
1800
23.8
26.6
29.4
32.2
185
700
800
900
16.8
18.2
19.6
770
600
15.4
565
705
300
11.2
1155
925
700
16.8
600
820
400
12.6
1170
240
80
8.1
550
940
500
14
1185
260
100
8.4
550
1055
600
15.4
1200
290
125
8.7
555
1285
800
18.2
1230
310
150
9.1
560
1520
1000
21
1260
350
200
9.8
585
1750
1200
23.8
1290
420
250
10.5
585
1980
1400
26.6
1320
480
300
11.2
585
2215
1600
29.4
1350
530
350
11.9
590
2445
1800
32.2
1380
580
400
12.6
615
600
200
9.8
1250
640
450
13.3
615
660
250
10.5
1260
690
500
14
615
720
300
11.2
1270
800
600
15.4
625
835
400
12.6
1290
920
700
16.8
640
950
500
14
1305
1030
800
18.2
655
1065
600
15.4
1310
240
80
8.1
605
1300
800
18.2
1340
260
100
8.4
610
1530
1000
21
1370
290
125
8.7
615
1760
1200
23.8
1400
310
150
9.1
620
1995
1400
26.6
1430
355
200
9.8
645
2225
1600
29.4
1460
420
250
10.5
645
2460
1800
32.2
1490
480
300
11.2
650
2690
2000
35
1520
530
350
11.9
660
1800
2000
32.2
35
dn
e1
80
8.1
330
80
8.1
100
8.4
330
80
360
150
200
250
XINXING PIPES
Body
DN
125
186
Branch
8.7
9.1
9.8
10.5
Unit:mm
dn
e1
165
980
450
13.3
675
8.1
175
1040
500
14
680
100
8.4
180
1500
600
15.4
705
400
80
8.1
190
1500
700
16.8
710
400
100
8.4
195
1500
800
18.2
725
400
125
8.7
200
1500
900
19.6
750
440
80
8.1
205
620
80
8.1
680
440
100
8.4
210
640
100
8.4
680
440
125
8.7
215
670
125
8.7
685
440
150
9.1
220
690
150
9.1
690
520
80
8.1
235
770
200
9.8
705
520
100
8.4
240
800
250
10.5
705
435
125
8.7
240
840
300
11.2
710
520
150
9.1
250
910
350
11.9
720
520
200
9.8
260
990
400
12.6
735
405
80
8.1
265
1020
450
13.3
735
700
100
8.4
275
1080
500
14
740
DN
900
1000
Branch
19.6
21
187
250
300
350
400
450
188
XINXING PIPES
10.5
11.2
11.9
12.6
13.3
485
125
8.7
280
1650
600
15.4
765
485
150
9.1
280
1650
700
16.8
700
200
9.8
325
1650
800
700
250
10.5
350
1650
425
80
8.1
295
800
100
8.4
480
125
505
950
450
13.3
475
1700
1000
21
945
770
1000
80
8.1
400
1910
1200
23.8
955
18.2
785
1000
100
8.4
400
820
80
8.1
870
900
19.6
800
1000
125
8.7
400
860
100
8.4
875
1650
1000
21
825
1000
150
9.1
400
880
125
8.7
880
300
610
80
8.1
740
1000
200
9.8
400
900
150
9.1
885
8.7
300
640
100
8.4
740
1000
250
10.5
400
910
200
9.8
890
150
9.1
310
670
125
8.7
745
1000
300
11.2
500
960
250
10.5
900
800
200
9.8
350
700
150
9.1
750
1000
350
11.9
500
1140
300
11.2
905
620
250
10.5
330
750
200
9.8
755
1000
400
12.6
500
1210
350
11.9
915
800
300
11.2
400
810
250
10.5
765
1000
450
13.3
500
1250
400
12.6
920
445
80
8.1
325
860
300
11.2
770
1000
500
14
500
1270
450
13.3
930
850
100
8.4
325
920
350
11.9
780
1100
80
8.1
450
1290
500
14
960
480
125
8.7
325
980
400
12.6
795
1100
100
8.4
450
1320
600
15.4
980
530
150
9.1
340
1030
450
13.3
795
1100
125
8.7
450
1440
700
16.8
990
850
200
9.8
325
1090
500
14
800
1100
150
9.1
450
1540
800
18.2
1010
645
250
10.5
360
1210
600
15.4
825
1100
200
9.8
450
1670
900
19.6
1020
680
300
11.2
350
1480
700
16.8
830
1100
250
10.5
450
1760
1000
21
1040
850
350
11.9
425
1540
800
18.2
845
1100
300
11.2
550
1880
1100
22.4
1055
470
80
8.1
355
1600
900
19.6
860
1100
350
11.9
550
1980
1200
23.8
1070
900
100
8.4
350
1660
1000
21
875
1100
400
12.6
550
2200
1400
26.6
1100
500
125
8.7
345
1780
1100
22.4
890
1100
450
13.3
550
1575
600
15.4
1035
550
150
9.1
370
610
80
8.1
795
1100
500
14
550
2040
1000
21
1095
900
200
9.8
360
640
100
8.4
800
1100
600
15.4
550
920
200
9.8
1040
665
250
10.5
390
670
125
8.7
805
500
80
8.1
500
980
250
10.5
1040
725
300
11.2
400
700
150
9.1
810
520
100
8.4
500
1150
300
11.2
1045
760
350
11.9
390
750
200
9.8
815
550
125
8.7
505
1270
400
12.6
1055
900
400
12.6
450
810
250
10.5
825
570
150
9.1
510
1300
500
14
1070
470
80
8.1
370
870
300
11.2
830
650
200
9.8
525
1380
600
15.4
1090
950
100
8.4
375
930
350
11.9
840
680
250
10.5
525
1600
800
18.2
1120
530
125
8.7
375
990
400
12.6
845
740
300
11.2
530
1820
1000
21
1150
570
150
9.1
400
1040
450
13.3
855
790
350
11.9
540
2040
1200
23.8
1180
950
200
9.8
375
1100
500
14
860
870
400
12.6
555
2260
1400
26.6
1210
690
250
10.5
420
1240
600
15.4
885
900
450
13.3
555
2480
1600
29.4
1240
745
300
11.2
430
1330
700
16.8
890
960
500
14
560
940
200
9.8
1140
790
350
11.9
420
1470
800
18.2
915
1180
600
15.4
575
1010
250
10.5
1145
860
400
12.6
450
1570
900
19.6
920
1200
700
16.8
600
1180
300
11.2
1150
1000
1100
1200
21
22.4
23.8
450
500
600
700
13.3
14
15.4
16.8
1200
1400
1500
1600
1800
23.8
26.6
28
29.4
32.2
189
800
900
18.2
19.6
540
80
8.1
560
1320
400
12.6
1165
560
100
8.4
560
1400
500
14
1185
590
125
8.7
565
1440
600
15.4
1200
610
150
9.1
570
1660
800
18.2
1230
690
200
9.8
585
1880
1000
21
1260
720
250
10.5
585
2100
1200
23.8
1290
760
300
11.2
590
2320
1400
26.6
1320
830
350
11.9
600
2540
1600
29.4
1350
910
400
12.6
615
2760
1800
32.2
1380
940
450
13.3
615
980
200
9.8
1240
1000
500
14
620
1055
250
10.5
1245
1350
600
15.4
645
1200
300
11.2
1250
1330
700
16.8
665
1350
400
12.6
1285
1350
800
18.2
675
1450
500
14
1295
580
80
8.1
620
1500
600
15.4
1310
600
100
8.4
620
1720
800
18.2
1340
630
125
8.7
625
1940
1000
21
1370
650
150
9.1
630
2160
1200
23.8
1400
730
200
9.8
645
2380
1400
26.6
1430
760
250
10.5
645
2600
1600
29.4
1460
800
300
11.2
650
2820
1800
32.2
1490
870
350
11.9
660
2950
2000
35
1520
950
400
12.6
675
1800
2000
132
35
Lu
dn
e1
Lu
80
8.1
170
80
8.1
100
8.4
170
80
190
150
200
250
XINXING PIPES
Body
DN
125
190
Branch
8.7
9.1
9.8
10.5
Unit:mm
Lu
dn
e1
Lu
85
590
400
12.6
530
8.1
95
640
450
13.3
535
100
8.4
95
690
500
14
535
170
80
8.1
105
800
600
15.4
535
195
100
8.4
110
920
700
16.8
535
225
125
8.7
110
1040
800
18.2
550
170
80
8.1
120
1150
900
19.6
575
195
100
8.4
120
240
80
8.1
560
230
125
8.7
125
260
100
8.4
560
255
150
9.1
125
290
125
8.7
560
175
80
8.1
145
310
150
9.1
570
200
100
8.4
145
360
200
9.8
570
230
125
8.7
145
420
250
10.5
570
255
150
9.1
150
480
300
11.2
575
315
200
9.8
155
530
350
11.9
575
180
80
8.1
170
590
400
12.6
580
200
100
8.4
170
640
450
13.3
585
230
125
8.7
175
690
500
14
585
DN
900
1000
Branch
19.6
21
191
250
300
350
400
450
192
XINXING PIPES
10.5
11.2
11.9
12.6
13.3
260
150
9.1
175
810
600
15.4
585
200
80
8.1
295
315
200
9.8
180
930
700
16.8
585
230
100
8.4
295
375
250
10.5
190
1040
800
18.2
605
250
125
8.7
190
80
8.1
195
1160
900
19.6
605
280
150
205
100
8.4
195
1270
1000
21
635
330
240
125
8.7
200
240
80
8.1
605
260
150
9.1
200
260
100
8.4
320
200
9.8
205
290
125
375
250
10.5
210
310
435
300
11.2
220
180
80
8.1
200
100
240
1290
1000
21
710
1520
1200
23.8
760
300
250
80
8.1
765
9.1
300
270
100
8.4
765
200
9.8
310
300
125
8.7
765
380
250
10.5
310
330
150
9.1
765
605
440
300
11.2
320
390
200
9.8
765
8.7
605
490
350
11.9
325
440
250
10.5
765
150
9.1
605
540
400
12.6
330
480
300
11.2
770
370
200
9.8
605
600
450
13.3
335
530
350
11.9
770
220
430
250
10.5
605
660
500
14
340
590
400
12.6
770
8.4
220
490
300
11.2
605
180
80
8.1
345
650
450
13.3
770
125
8.7
225
540
350
11.9
610
200
100
8.4
345
710
500
14
770
250
150
9.1
225
600
400
12.6
610
250
125
8.7
350
820
600
15.4
775
300
200
9.8
230
640
450
13.3
610
260
150
9.1
350
940
700
16.8
785
360
250
10.5
240
690
500
14
615
320
200
9.8
360
1050
800
18.2
815
420
300
11.2
245
810
600
15.4
620
380
250
10.5
360
1170
900
19.6
815
480
350
11.9
250
930
700
16.8
630
430
300
11.2
370
1290
1000
21
815
170
80
8.1
245
1040
800
18.2
660
490
350
11.9
375
1400
1100
22.4
825
190
100
8.4
245
1160
900
19.6
665
550
400
12.6
380
1520
1200
23.8
835
240
125
8.7
250
1270
1000
21
670
610
450
13.3
385
1740
1400
26.6
855
250
150
9.1
250
1380
1100
22.4
680
670
500
14
390
855
600
15.4
850
310
200
9.8
255
240
80
8.1
665
780
600
15.4
400
1320
1000
21
895
360
250
10.5
260
260
100
8.4
665
210
80
8.1
395
400
200
9.8
865
420
300
11.2
265
290
125
8.7
665
230
100
8.4
405
455
250
10.5
865
480
350
11.9
275
310
150
9.1
675
250
125
8.7
405
515
300
11.2
870
540
400
12.6
280
360
200
9.8
675
280
150
9.1
405
630
400
12.6
880
180
80
8.1
270
420
250
10.5
675
330
200
9.8
415
745
500
14
890
200
100
8.4
270
480
300
11.2
680
390
250
10.5
415
860
600
15.4
900
250
125
8.7
275
530
350
11.9
685
440
300
11.2
415
1095
800
18.2
925
260
150
9.1
275
590
400
12.6
685
500
350
11.9
420
1325
1000
21
945
310
200
9.8
280
650
450
13.3
695
560
400
12.6
425
1560
1200
23.8
965
370
250
10.5
285
710
500
14
695
610
450
13.3
430
1970
1400
26.6
1030
430
300
11.2
290
820
600
15.4
695
680
500
14
430
2200
1600
29.4
1050
480
350
11.9
300
940
700
16.8
695
770
600
15.4
430
410
200
9.8
970
540
400
12.6
305
1050
800
18.2
710
910
700
16.8
455
470
250
10.5
970
600
450
13.3
310
1170
900
19.6
710
240
80
8.1
445
530
300
11.2
970
1000
1100
1200
21
22.4
23.8
500
600
700
800
14
15.4
16.8
18.2
1200
1400
1500
1600
1800
23.8
26.6
28
29.4
32.2
193
800
900
18.2
19.6
(26)Socket-Spigot Tees with Socket Branch (Refer to Figure 26 and Table 26)
260
100
8.4
455
640
400
12.6
980
290
125
8.7
455
760
500
14
990
310
150
9.1
460
875
600
15.4
1000
360
200
9.8
465
1105
800
18.2
1025
420
250
10.5
465
1340
1000
21
1045
480
300
11.2
470
1570
1200
23.8
1065
530
350
11.9
475
1800
1400
26.6
1090
590
400
12.6
475
2215
1600
29.4
1150
640
450
13.3
485
2260
1800
32.2
1130
690
500
14
485
420
200
9.8
1080
800
600
15.4
485
540
300
11.2
1080
920
700
16.8
495
650
400
12.6
1080
1030
800
18.2
515
770
500
14
1090
240
80
8.1
505
885
600
15.4
1100
260
100
8.4
505
1300
800
18.2
1165
290
125
8.7
505
1350
1000
21
1185
310
150
9.1
515
1760
1200
23.8
1210
360
200
9.8
520
1815
1400
26.6
1190
420
250
10.5
520
2225
1600
29.4
1250
480
300
11.2
525
2460
1800
32.2
1275
DN
Lu
DN
e1
Lu
530
350
11.9
525
2690
2000
35
1295
80
8.1
85
275
80
8.1
100
8.4
85
275
80
95
275
85
1800
2000
32.2
35
125
150
200
250
194
XINXING PIPES
8.7
9.1
9.8
10.5
Branch
Unit:mm
Body
Lu
DN
e1
Lu
85
295
590
400
12.6
530
8.1
95
320
610
450
13.3
535
100
8.4
95
350
600
500
14
535
280
80
8.1
105
410
660
600
15.4
535
95
290
100
8.4
110
470
720
700
16.8
535
110
295
125
8.7
110
520
815
800
18.2
550
85
275
80
8.1
120
585
835
900
19.6
575
100
280
100
8.4
120
120
420
80
8.1
550
115
305
125
8.7
120
130
435
100
8.4
560
130
310
150
9.1
125
145
445
125
8.7
560
90
275
80
8.1
145
155
465
150
9.1
570
100
280
100
8.4
145
180
495
200
9.8
570
115
305
125
8.7
145
210
525
250
10.5
570
130
310
150
9.1
150
240
545
300
11.2
575
160
340
200
9.8
155
265
575
350
11.9
575
90
300
80
8.1
170
295
600
400
12.6
580
100
280
100
8.4
170
320
620
450
13.3
585
DN
900
1000
Branch
19.6
21
195
250
300
350
400
450
196
10.5
11.2
11.9
12.6
13.3
XINXING PIPES
300
525
450
13.3
290
595
895
900
19.6
710
585
100
320
80
8.1
295
650
950
1000
21
710
16.8
585
115
330
100
8.4
295
770
1070
1200
23.8
760
800
18.2
605
125
345
125
8.7
300
125
500
80
8.1
755
880
900
19.6
605
140
360
150
9.1
300
135
515
100
8.4
755
645
945
1000
21
635
165
390
200
9.8
300
150
525
125
8.7
760
225
120
435
80
8.1
600
195
395
250
10.5
310
165
540
150
9.1
765
9.1
200
130
450
100
8.4
600
225
425
300
11.2
315
195
570
200
9.8
765
200
9.8
205
145
460
125
8.7
600
255
455
350
11.9
315
220
600
250
10.5
765
370
250
10.5
210
155
480
150
9.1
600
285
485
400
12.6
315
240
630
300
11.2
770
220
400
300
11.2
220
185
510
200
9.8
605
300
525
450
13.3
315
265
655
350
11.9
770
90
300
80
8.1
215
215
540
250
10.5
605
340
540
500
14
325
295
680
400
12.6
770
100
310
100
8.4
215
245
560
300
11.2
605
90
325
80
8.1
345
325
700
450
13.3
770
120
325
125
8.7
215
270
590
350
11.9
610
100
330
100
8.4
345
355
735
500
14
770
125
340
150
9.1
215
300
615
400
12.6
610
125
345
125
8.7
350
410
790
600
15.4
775
160
340
200
9.8
220
320
635
450
13.3
610
130
360
150
9.1
350
470
845
700
16.8
785
190
370
250
10.5
235
345
665
500
14
615
160
390
200
9.8
350
525
905
800
18.2
815
220
400
300
11.2
235
405
725
600
15.4
620
190
415
250
10.5
360
600
900
900
19.6
815
250
430
350
11.9
235
415
715
700
16.8
630
230
430
300
11.2
365
660
960
1000
21
815
85
300
80
8.1
240
535
835
800
18.2
660
255
455
350
11.9
365
700
1065
1100
22.4
825
95
310
100
8.4
240
590
890
900
19.6
665
285
485
400
12.6
365
775
1075
1200
23.8
835
120
330
125
8.7
250
635
1060
1000
21
670
305
525
450
13.3
365
890
1190
1400
26.6
855
125
340
150
9.1
250
705
1005
1100
22.4
680
345
545
500
14
375
200
720
200
9.8
865
165
345
200
9.8
250
120
475
80
8.1
655
400
600
600
15.4
380
230
750
250
10.5
865
195
375
250
10.5
260
130
490
100
8.4
665
105
345
80
8.1
395
260
780
300
11.2
870
220
400
300
11.2
265
145
500
125
8.7
665
115
345
100
8.4
405
315
830
400
12.6
880
250
430
350
11.9
265
155
515
150
9.1
675
125
360
125
8.7
405
370
885
500
14
890
280
460
400
12.6
265
180
545
200
9.8
675
140
370
150
9.1
405
430
935
600
15.4
900
90
320
80
8.1
265
210
575
250
10.5
675
165
400
200
9.8
415
550
1050
800
18.2
925
100
330
100
8.4
265
240
605
300
11.2
680
195
430
250
10.5
415
660
1165
1000
21
945
125
345
125
8.7
275
265
630
350
11.9
685
230
480
300
11.2
415
780
1275
1200
23.8
965
130
360
150
9.1
275
295
655
400
12.6
685
260
510
350
11.9
420
985
1380
1400
26.6
1030
155
390
200
9.8
280
325
675
450
13.3
695
290
540
400
12.6
425
1010
1490
1600
29.4
1050
185
415
250
10.5
285
355
710
500
14
695
305
525
450
13.3
430
205
720
200
9.8
970
215
445
300
11.2
290
385
675
600
15.4
695
345
595
500
14
430
235
750
250
10.5
970
240
460
350
11.9
290
470
820
700
16.8
695
405
655
600
15.4
430
265
780
300
11.2
970
270
500
400
12.6
290
535
835
800
18.2
710
465
715
700
16.8
455
320
830
400
12.6
980
115
315
125
8.7
170
345
650
500
14
585
130
310
150
9.1
175
415
715
600
15.4
160
340
200
9.8
180
470
770
700
190
370
250
10.5
190
530
830
95
300
80
8.1
190
580
105
285
100
8.4
195
120
320
125
8.7
130
310
150
160
340
190
1000
1100
1200
21
22.4
23.8
450
500
600
700
13.3
14
15.4
16.8
1200
1400
1400
1600
1800
23.8
26.6
26.6
29.4
32.2
197
800
900
18.2
19.6
120
355
80
8.1
445
380
885
500
14
990
130
355
100
8.4
455
440
935
600
15.4
1000
145
370
125
8.7
455
550
1050
800
18.2
1025
155
380
150
9.1
460
650
1165
1000
21
1045
180
410
200
9.8
465
785
1275
1200
23.8
1065
210
440
250
10.5
465
850
1380
1400
26.6
1090
240
450
300
11.2
470
1000
1490
1600
29.4
1150
265
485
350
11.9
475
1100
1595
1800
32.2
1130
290
540
400
12.6
475
210
720
200
9.8
1080
320
535
450
13.3
485
240
750
250
10.5
1080
350
600
500
14
485
270
780
300
11.2
1080
410
660
600
15.4
485
325
830
400
12.6
1080
460
690
700
16.8
495
385
885
500
14
1090
525
775
800
18.2
515
440
935
600
15.4
1100
120
410
80
8.1
495
650
1050
800
18.2
1165
130
425
100
8.4
505
675
1165
1000
21
1185
145
435
125
8.7
505
880
1275
1200
23.8
1210
155
455
150
9.1
515
910
1380
1400
26.6
1230
180
485
200
9.8
520
1110
1490
1600
29.4
1250
210
515
250
10.5
520
1230
1595
1800
32.2
1275
240
535
300
11.2
525
1345
1705
2000
35
1295
265
565
350
11.9
525
1800
2000
32.2
35
(27)Socket-Spigot Tees with Flange Branch (Refer to Figure 27 and Table 27)
Lu
dn
e1
Lu
80
8.1
85
275
80
8.1
100
8.4
85
275
80
95
285
85
150
200
250
XINXING PIPES
Body
DN
125
198
Branch
8.7
9.1
9.8
10.5
Unit:mm
Lu
dn
e1
Lu
165
295
630
400
12.6
675
8.1
175
320
660
450
13.3
665
100
8.4
180
345
700
500
14
670
275
80
8.1
190
400
760
600
15.4
685
100
285
100
8.4
195
460
795
700
16.8
700
110
275
125
8.7
200
520
855
800
18.2
715
85
275
80
8.1
205
585
905
900
19.6
750
100
285
100
8.4
210
120
450
80
8.1
670
110
285
125
8.7
215
130
460
100
8.4
670
130
310
150
9.1
220
145
475
125
8.7
675
90
275
80
8.1
235
155
495
150
9.1
680
100
280
100
8.4
240
180
525
200
9.8
705
110
285
125
8.7
240
210
555
250
10.5
705
130
310
150
9.1
250
240
575
300
11.2
710
150
340
200
9.8
260
265
610
350
11.9
720
90
315
80
8.1
265
295
640
400
12.6
735
100
325
100
8.4
270
320
670
450
13.3
725
DN
900
1000
Branch
19.6
21
199
250
300
350
400
450
200
10.5
11.2
11.9
12.6
13.3
XINXING PIPES
115
325
125
8.7
255
345
710
500
14
730
130
360
150
9.1
280
405
770
600
15.4
150
385
200
9.8
290
465
805
700
180
415
250
10.5
300
520
865
90
340
80
8.1
295
580
105
355
100
8.4
300
115
360
125
8.7
130
390
150
160
415
190
310
555
450
13.3
460
595
965
900
19.6
920
745
95
355
80
8.1
400
650
1030
1000
21
945
16.8
760
110
355
100
8.4
420
760
1145
1200
23.8
955
800
18.2
775
120
360
125
8.7
420
170
525
80
8.1
870
915
900
19.6
790
140
390
150
9.1
425
210
535
100
8.4
875
645
980
1000
21
825
165
415
200
9.8
440
225
550
125
8.7
880
285
120
465
80
8.1
730
190
445
250
10.5
440
240
570
150
9.1
880
9.1
310
130
475
100
8.4
730
220
475
300
11.2
440
270
595
200
9.8
890
200
9.8
320
145
490
125
8.7
735
245
500
350
11.9
450
280
625
250
10.5
895
445
250
10.5
330
155
510
150
9.1
740
280
530
400
12.6
480
325
655
300
11.2
905
215
475
300
11.2
340
180
540
200
9.8
745
300
555
450
13.3
480
355
685
350
11.9
910
95
345
80
8.1
325
210
570
250
10.5
755
340
580
500
14
500
385
715
400
12.6
920
100
355
100
8.4
330
240
590
300
11.2
760
100
355
80
8.1
460
415
745
450
13.3
925
115
360
125
8.7
315
265
625
350
11.9
770
100
355
100
8.4
460
440
785
500
14
935
135
390
150
9.1
340
300
655
400
12.6
795
120
360
125
8.7
465
515
845
600
15.4
980
160
415
200
9.8
350
325
685
450
13.3
795
130
390
150
9.1
470
560
880
700
16.8
990
190
445
250
10.5
350
350
725
500
14
795
170
415
200
9.8
500
630
940
800
18.2
1010
210
475
300
11.2
350
415
785
600
15.4
825
190
445
250
10.5
490
675
990
900
19.6
1020
240
500
350
11.9
380
470
820
700
16.8
830
215
475
300
11.2
500
750
1055
1000
21
1040
95
355
80
8.1
355
525
880
800
18.2
835
245
500
350
11.9
510
790
1105
1100
22.4
1045
105
355
100
8.4
360
585
930
900
19.6
850
285
530
400
12.6
540
850
1170
1200
23.8
1050
115
360
125
8.7
345
640
995
1000
21
870
305
555
450
13.3
530
85
275
80
8.1
165
135
390
150
9.1
370
695
1045
1100
22.4
880
335
580
500
14
540
225
755
100
8.4
1025
160
415
200
9.8
380
120
500
80
8.1
790
400
635
600
15.4
580
260
755
150
9.1
1025
190
445
250
10.5
390
130
510
100
8.4
790
105
345
80
8.1
490
290
730
200
9.8
1030
220
475
300
11.2
400
145
525
125
8.7
795
115
345
100
8.4
490
320
760
250
10.5
1040
240
500
350
11.9
400
155
545
150
9.1
800
125
361
125
8.7
495
345
790
300
11.2
1045
280
530
400
12.6
420
180
570
200
9.8
805
140
370
150
9.1
500
405
860
400
12.6
1060
95
355
80
8.1
370
210
600
250
10.5
815
170
385
200
9.8
525
520
915
600
15.4
1090
110
355
100
8.4
390
240
630
300
11.2
820
195
430
250
10.5
515
640
970
800
18.2
1120
115
360
125
8.7
405
265
660
350
11.9
830
220
440
300
11.2
520
750
1090
1000
21
1150
135
390
150
9.1
400
295
690
400
12.6
835
250
475
350
11.9
530
870
1210
1200
23.8
1180
165
415
200
9.8
410
325
720
450
13.3
845
285
495
400
12.6
555
985
1315
1400
26.6
1210
195
445
250
10.5
420
355
760
500
14
850
305
525
450
13.3
545
1100
1430
1600
29.4
1240
220
475
300
11.2
430
420
820
600
15.4
885
340
560
500
14
550
300
730
200
9.8
1150
240
500
350
11.9
440
470
855
700
16.8
885
385
595
600
15.4
565
320
760
250
10.5
1150
280
530
400
12.6
450
535
915
800
18.2
915
460
690
700
16.8
600
350
790
300
11.2
1155
1000
1100
1200
21
22.4
23.8
450
500
600
700
13.3
14
15.4
16.8
1200
1400
1600
1800
23.8
26.6
29.4
32.2
201
800
900
18.2
19.6
120
355
80
8.1
550
410
860
400
12.6
1170
130
355
100
8.4
550
470
915
500
14
1185
145
371
125
8.7
555
525
970
600
15.4
1200
155
381
150
9.1
560
640
1090
800
18.2
1230
175
395
200
9.8
585
760
1210
1000
21
1260
210
441
250
10.5
585
875
1315
1200
23.8
1290
240
451
300
11.2
585
990
1430
1400
26.6
1320
265
485
350
11.9
590
1110
1540
1600
29.4
1350
290
505
400
12.6
615
1225
1615
1800
32.2
1380
320
535
450
13.3
615
300
730
200
9.8
1250
345
571
500
14
615
330
760
250
10.5
1260
400
605
600
15.4
625
360
790
300
11.2
1265
460
700
700
16.8
640
415
860
400
12.6
1280
515
760
800
18.2
655
475
915
500
14
1295
120
440
80
8.1
605
530
970
600
15.4
1310
130
450
100
8.4
610
640
1090
800
18.2
1340
145
465
125
8.7
615
765
1210
1000
21
1370
155
485
150
9.1
620
880
1315
1200
23.8
1400
180
515
200
9.8
645
1000
1430
1400
26.6
1430
210
545
250
10.5
645
1110
1540
1600
29.4
1460
240
565
300
11.2
650
1230
1615
1800
32.2
1490
265
600
350
11.9
660
1345
1725
2000
35
1520
1800
2000
32.2
35
(28)Double-Socket Level Invert Tees with Flanged Branch (Refer to Figure 28 and Table 28)
Table 28 Technical Parameters for Double-Socket Level Invert Tees with Flanged Branch
Body
e
dn
e1
100
8.4
170
80
8.1
175
150
9.1
170
80
8.1
210
195
100
8.4
175
80
200
250
300
XINXING PIPES
Body
DN
200
202
Branch
9.8
10.5
11.2
800
18.2
Branch
L
dn
e1
690
500
14
660
800
600
15.4
670
220
240
80
8.1
630
8.1
235
260
100
8.4
640
100
8.4
240
290
125
8.7
650
255
150
9.1
250
310
150
9.1
640
180
80
8.1
265
355
200
9.8
640
200
100
8.4
270
420
250
10.5
645
260
150
9.1
280
480
300
11.2
650
315
200
9.8
290
530
350
11.9
670
180
80
8.1
295
590
400
12.6
680
205
100
8.4
300
640
450
13.3
685
230
125
8.7
305
690
500
14
690
260
150
9.1
310
800
600
15.4
705
320
200
9.8
320
240
80
8.1
660
380
250
10.5
330
260
100
8.4
670
DN
Unit:mm
900
1000
19.6
21
203
350
400
450
500
600
204
XINXING PIPES
11.9
12.6
13.3
14
15.4
185
80
8.1
325
290
125
8.7
680
340
200
9.8
500
480
150
9.1
910
205
100
8.4
330
310
150
9.1
700
380
250
10.5
510
540
200
9.8
920
230
125
8.7
335
360
200
9.8
700
430
300
11.2
520
560
250
10.5
925
270
150
9.1
340
420
250
10.5
705
490
350
11.9
530
650
300
11.2
935
325
200
9.8
350
480
300
11.2
710
570
400
12.6
540
710
350
11.9
940
385
250
10.5
360
530
350
11.9
720
610
450
13.3
550
770
400
12.6
945
420
300
11.2
370
595
400
12.6
730
670
500
14
560
830
450
13.3
955
185
80
8.1
355
640
450
13.3
745
210
80
8.1
520
880
500
14
965
210
100
8.4
360
690
500
14
750
230
100
8.4
540
1030
600
15.4
970
240
125
8.7
365
810
600
15.4
765
250
125
8.7
540
460
100
8.4
1015
270
150
9.1
370
240
80
8.1
740
280
150
9.1
550
580
200
9.8
1050
325
200
9.8
380
260
100
8.4
750
345
200
9.8
560
635
250
10.5
1060
385
250
10.5
390
290
125
8.7
760
390
250
10.5
570
695
300
11.2
1065
440
300
11.2
400
310
150
9.1
750
440
300
11.2
580
810
400
12.6
1080
480
350
11.9
410
360
200
9.8
750
500
350
11.9
590
925
500
14
1095
215
100
8.4
390
420
250
10.5
755
75
400
12.6
600
1040
600
15.4
1110
240
125
8.7
395
480
300
11.2
760
610
450
13.3
610
595
200
9.8
1260
270
150
9.1
400
530
350
11.9
765
680
500
14
620
650
250
10.5
1170
330
200
9.8
410
600
400
12.6
775
770
600
15.4
630
705
300
11.2
1175
390
250
10.5
420
650
450
13.3
805
240
80
8.1
580
820
400
12.6
1190
445
300
11.2
430
700
500
14
810
260
100
8.4
590
940
500
14
1205
480
350
11.9
440
830
600
15.4
825
290
125
8.7
590
1055
600
15.4
1220
560
400
12.6
450
240
80
8.1
820
310
150
9.1
600
600
200
9.8
1270
190
80
8.1
415
260
100
8.4
820
350
200
9.8
605
660
250
10.5
1280
215
100
8.4
420
290
125
8.7
825
420
250
10.5
610
720
300
11.2
1290
240
125
8.7
425
310
150
9.1
830
480
300
11.2
620
835
400
12.6
1310
280
150
9.1
430
360
200
9.8
840
530
350
11.9
630
950
500
14
1325
330
200
9.8
440
420
250
10.5
850
580
400
12.6
640
1065
600
15.4
1330
380
250
10.5
450
480
300
11.2
860
640
450
13.3
650
440
300
11.2
460
530
350
11.9
870
490
350
11.9
470
590
400
12.6
880
565
400
12.6
480
650
450
13.3
890
600
450
13.3
490
710
500
14
870
195
80
8.1
475
840
600
15.4
885
200
100
8.4
480
340
80
8.1
905
240
125
8.7
485
420
100
8.4
905
260
150
9.1
490
450
125
8.7
910
1000
1100
1200
1400
21
22.4
23.8
26.6
600
700
800
15.4
16.8
18.2
1400
1600
1800
2000
26.6
29.4
32.2
35
205
(29)All Socket Level Invert Tees (Refer to Figure 29 and Table 29)
300
350
400
11.2
11.9
12.6
Body
Body
DN
dn
e1
100
8.4
170
80
8.1
100
125
8.7
170
80
8.1
110
195
100
8.4
115
170
80
8.1
195
100
230
150
200
250
300
206
Branch
XINXING PIPES
9.1
9.8
10.5
11.2
Unit:mm
DN
150
9.1
180
240
80
8.1
535
320
200
9.8
185
260
100
8.4
540
375
250
10.5
215
290
125
8.7
540
180
80
8.1
200
310
150
9.1
545
200
100
8.4
200
360
200
9.8
550
250
150
9.1
205
420
250
10.5
555
300
200
9.8
210
480
300
11.2
560
360
250
10.5
240
530
350
11.9
565
420
300
11.2
265
590
400
12.6
570
170
80
8.1
225
640
450
13.3
575
190
100
8.4
225
690
500
14
580
220
125
8.7
250
800
600
15.4
590
250
150
9.1
230
230
80
8.1
595
310
200
9.8
235
260
100
8.4
600
360
250
10.5
245
280
125
8.7
605
420
300
11.2
270
310
150
9.1
610
480
350
11.9
295
370
200
9.8
610
180
80
8.1
250
430
250
10.5
615
200
100
8.4
250
490
300
11.2
620
225
125
8.7
255
540
350
11.9
625
260
150
9.1
255
600
400
12.6
630
310
200
9.8
260
640
450
13.3
630
1000
1100
21
22.4
dn
e1
590
400
12.6
470
640
450
13.3
475
370
250
10.5
270
690
500
14
635
690
500
14
480
430
300
11.2
275
810
600
15.4
640
120
800
600
15.4
495
480
350
11.9
300
240
80
8.1
635
8.4
120
240
80
8.1
485
540
400
12.6
325
260
100
8.4
640
125
8.7
130
260
100
8.4
490
200
80
8.1
275
290
125
8.7
640
175
80
8.1
125
290
125
8.7
490
230
100
8.4
275
310
150
9.1
645
200
100
8.4
125
310
150
9.1
495
225
125
8.7
275
360
200
9.8
650
255
150
9.1
130
360
200
9.8
500
280
150
9.1
280
420
250
10.5
655
180
80
8.1
150
420
250
10.5
505
330
200
9.8
285
480
300
11.2
660
200
100
8.4
150
480
300
11.2
510
380
250
10.5
295
530
350
11.9
665
260
150
9.1
155
530
350
11.9
515
440
300
11.2
300
590
400
12.6
670
315
200
9.8
160
590
400
12.6
520
490
350
11.9
305
650
450
13.3
675
190
80
8.1
175
640
450
13.3
525
540
400
12.6
330
710
500
14
680
205
100
8.4
175
690
500
14
530
600
450
13.3
355
820
600
15.4
695
215
125
8.7
200
800
600
15.4
545
180
80
8.1
325
250
80
8.1
745
800
900
Branch
260
18.2
19.6
450
500
600
13.3
14
15.4
1200
1400
23.8
26.6
207
600
700
800
15.4
16.8
18.2
(30)Socket Spigot Level Invert Tees with Flanged Branch (Refer to Figure 30 and Table 30)
200
100
8.4
325
270
100
8.4
745
230
125
8.7
325
300
125
8.7
755
260
150
9.1
330
330
150
9.1
755
320
200
9.8
335
390
200
9.8
760
380
250
10.5
345
440
250
10.5
765
430
300
11.2
350
490
300
11.2
770
490
350
11.9
355
530
350
11.9
775
550
400
12.6
360
590
400
12.6
780
610
450
13.3
385
650
450
13.3
785
670
500
14
390
700
500
14
790
210
80
8.1
385
820
600
15.4
800
230
100
8.4
390
1520
1200
23.8
870
250
125
8.7
390
400
200
9.8
885
280
150
9.1
395
455
250
10.5
885
330
200
9.8
400
515
300
11.2
890
390
250
10.5
405
630
400
12.6
900
440
300
11.2
410
745
500
14
910
500
350
11.9
415
860
600
15.4
920
560
400
12.6
420
410
200
9.8
990
610
450
13.3
425
470
250
10.5
990
680
500
14
430
530
300
11.2
990
770
600
15.4
445
640
400
12.6
1000
DN
Lu
dn
e1
Lu
240
80
8.1
435
760
500
14
1010
100
8.4
85
275
80
8.1
175
260
100
8.4
440
875
600
15.4
1020
275
80
8.1
210
125
8.7
440
420
200
9.8
1100
9.1
85
290
150
100
285
100
8.4
310
150
9.1
445
480
250
10.5
1100
90
275
80
360
200
9.8
450
540
300
11.2
1100
100
280
420
250
10.5
455
650
400
12.6
1100
130
480
300
11.2
460
770
500
14
1110
530
350
11.9
465
885
600
15.4
1120
1400
1600
1800
2000
26.6
29.4
32.2
35
able 30 Technical Parameters for Socket Spigot Level Invert Tees with Flanged Branch
Body
200
250
300
208
XINXING PIPES
9.8
10.5
11.2
Branch
Unit:mm
Body
Lu
dn
e1
320
535
450
13.3
650
345
571
500
14
660
220
400
605
600
15.4
670
8.1
235
120
440
80
8.1
640
100
8.4
240
130
450
100
8.4
640
310
150
9.1
250
145
465
125
8.7
640
90
315
80
8.1
265
155
485
150
9.1
640
100
325
100
8.4
270
180
515
200
9.8
645
130
360
150
9.1
280
210
545
250
10.5
650
160
385
200
9.8
290
240
565
300
11.2
660
90
340
80
8.1
295
265
600
350
11.9
670
105
355
100
8.4
295
295
630
400
12.6
680
130
390
150
9.1
310
320
660
450
13.3
685
150
415
200
9.8
320
345
700
500
14
690
190
445
250
10.5
330
400
760
600
15.4
705
DN
800
900
Branch
18.2
19.6
209
350
400
450
500
600
210
11.9
12.6
13.3
14
15.4
XINXING PIPES
95
345
80
8.1
325
120
450
80
8.1
680
130
390
150
9.1
490
210
535
100
8.4
910
100
355
100
8.4
330
130
460
100
8.4
700
170
415
200
9.8
500
225
550
125
8.7
920
115
360
125
8.7
335
145
475
125
8.7
700
190
445
250
10.5
510
240
570
150
9.1
925
135
390
150
9.1
340
155
495
150
9.1
705
215
475
300
11.2
520
270
595
200
9.8
935
160
415
200
9.8
350
180
525
200
9.8
710
245
500
350
11.9
530
280
625
250
10.5
940
190
445
250
10.5
360
210
555
250
10.5
720
285
530
400
12.6
540
325
655
300
11.2
945
210
475
300
11.2
370
240
575
300
11.2
730
305
555
450
13.3
550
355
685
350
11.9
955
95
355
80
8.1
355
265
610
350
11.9
740
335
580
500
14
560
385
715
400
12.6
965
105
355
100
8.4
360
295
640
400
12.6
750
105
345
80
8.1
520
415
745
450
13.3
975
115
360
125
8.7
365
320
670
450
13.3
750
115
345
100
8.4
540
440
785
500
14
985
135
390
150
9.1
370
345
710
500
14
750
125
361
125
8.7
540
500
845
600
15.4
990
160
415
200
9.8
380
405
770
600
15.4
765
140
370
150
9.1
550
290
730
200
9.8
1050
190
445
250
10.5
390
120
465
80
8.1
750
170
385
200
9.8
560
320
760
250
10.5
1060
220
475
300
11.2
400
130
475
100
8.4
750
195
430
250
10.5
570
345
790
300
11.2
1065
240
500
350
11.9
410
145
490
125
8.7
750
220
440
300
11.2
580
405
860
400
12.6
1080
95
355
80
8.1
385
155
510
150
9.1
755
250
475
350
11.9
590
465
895
500
14
1095
110
355
100
8.4
390
180
540
200
9.8
760
285
495
400
12.6
600
520
915
600
15.4
1110
115
360
125
8.7
395
210
570
250
10.5
765
305
525
450
13.3
610
300
730
200
9.8
1170
135
390
150
9.1
400
240
590
300
11.2
775
340
560
500
14
620
320
760
250
10.5
1170
165
415
200
9.8
410
265
625
350
11.9
820
385
595
600
15.4
630
350
790
300
11.2
1175
195
445
250
10.5
420
295
655
400
12.6
820
120
355
80
8.1
580
410
860
400
12.6
1190
220
475
300
11.2
430
325
685
450
13.3
805
130
355
100
8.4
580
470
915
500
14
1205
240
500
350
11.9
440
350
725
500
14
810
145
371
125
8.7
600
525
970
600
15.4
1220
280
530
400
12.6
450
410
785
600
15.4
825
155
381
150
9.1
605
300
730
200
9.8
1270
95
355
80
8.1
415
120
500
80
8.1
825
180
395
200
9.8
610
330
760
250
10.5
1280
110
355
100
8.4
420
130
510
100
8.4
830
210
441
250
10.5
620
360
790
300
11.2
1290
120
360
125
8.7
425
145
525
125
8.7
840
240
451
300
11.2
630
415
860
400
12.6
1310
140
390
150
9.1
430
155
545
150
9.1
850
265
485
350
11.9
630
475
915
500
14
1325
165
415
200
9.8
440
180
570
200
9.8
860
295
505
400
12.6
640
530
970
600
15.4
1330
190
445
250
10.5
450
210
600
250
10.5
870
220
475
300
11.2
460
240
630
300
11.2
880
245
500
350
11.9
470
265
660
350
11.9
890
280
530
400
12.6
480
295
690
400
12.6
905
300
555
450
13.3
490
325
720
450
13.3
905
100
355
80
8.1
475
355
760
500
14
910
100
355
100
8.4
480
410
820
600
15.4
910
120
360
125
8.7
485
170
525
80
8.1
910
1000
1100
1200
1400
21
22.4
23.8
26.6
600
700
800
15.4
16.8
18.2
1400
1600
1800
2000
26.6
29.4
32.2
35
211
250
300
350
DN
dn
80
80
100
size
L
8.1
8.1
240
85
100
8.4
630
105
8.1
265
85
125
8.7
630
120
8.4
265
95
150
9.1
635
135
8.1
295
85
9.8
640
165
8.4
300
100
10.5
645
190
125
8.7
300
115
300
11.2
650
220
80
8.1
325
85
350
11.9
660
250
8.4
330
100
400
12.6
665
280
8.7
330
115
100
8.4
690
105
150
9.1
335
125
150
9.1
695
135
80
8.1
385
90
200
9.8
700
165
100
8.4
390
100
10.5
705
195
8.7
390
115
11.2
710
225
150
9.1
395
130
350
11.9
720
250
200
9.8
400
160
400
12.6
725
280
8.1
445
90
450
13.3
730
310
8.4
80
125
150
200
250
212
XINXING PIPES
100
100
125
125
80
8.7
9.1
9.8
10.5
400
450
200
250
250
300
8.4
450
100
100
8.4
750
110
125
8.7
450
115
150
9.1
755
140
9.1
455
130
200
9.8
760
145
200
9.8
460
160
250
10.5
770
195
250
10.5
465
190
11.2
775
225
80
8.1
505
90
350
11.9
780
255
100
8.4
510
100
400
12.6
785
280
125
8.7
510
115
450
13.3
790
310
9.1
515
130
500
14
795
340
200
9.8
520
160
100
8.4
870
110
250
10.5
525
190
150
9.1
880
140
300
11.2
530
220
200
9.8
885
170
100
8.4
570
105
250
10.5
890
200
125
8.7
570
120
11.2
895
225
150
9.1
575
135
11.9
900
255
9.8
580
160
400
12.6
905
285
250
10.5
585
190
450
13.3
910
315
300
11.2
590
220
500
14
915
345
350
11.9
595
250
600
15.4
930
400
150
150
200
10.5
11.2
11.9
500
600
300
300
350
14
15.4
size
L
100
e1
dn
e1
80
DN
Unit:mm
100
12.6
13.3
213
200
250
300
DN
dn
80
80
100
size
h
8.1
8.1
390
85
8.1
415
8.4
150
200
100
8.4
780
105
85
125
8.7
780
120
415
95
150
9.1
785
135
8.1
445
85
9.8
790
165
8.4
445
95
10.5
795
190
125
8.7
450
110
300
11.2
800
220
80
8.1
475
85
350
11.9
810
250
8.4
480
100
400
12.6
815
280
8.7
480
115
100
8.4
840
105
150
9.1
485
125
150
9.1
845
135
80
8.1
535
90
9.8
850
165
8.4
540
100
10.5
855
195
8.7
540
115
300
11.2
865
225
9.1
545
130
350
11.9
870
250
100
100
125
100
125
150
214
XINXING PIPES
dn
8.4
80
125
DN
100
e1
size
e1
80
Unit:mm
8.7
9.1
9.8
400
450
200
250
200
250
12.6
13.3
200
9.8
550
160
12.6
875
280
80
8.1
595
90
13.3
880
310
100
8.4
600
100
100
8.4
900
110
8.7
600
115
150
9.1
915
140
9.1
605
130
200
9.8
915
165
200
9.8
610
160
250
10.5
920
195
250
10.5
615
190
11.2
925
225
80
8.1
655
90
350
11.9
930
245
100
8.4
660
100
400
12.6
935
280
125
8.7
660
115
450
13.3
940
310
9.1
665
130
500
14
945
340
200
9.8
670
160
100
8.4
1020
110
250
10.5
675
190
150
9.1
1030
140
300
11.2
680
220
200
9.8
1035
170
100
8.4
720
105
250
10.5
1040
200
125
8.7
720
120
11.2
1045
225
150
9.1
725
135
11.9
1050
255
9.8
730
160
400
12.6
1055
285
250
10.5
735
190
450
13.3
1060
315
300
11.2
740
220
500
14
1065
345
350
11.9
745
250
600
15.4
1080
400
125
150
150
200
9.8
10.5
11.2
11.9
450
500
600
400
450
300
300
350
13.3
14
15.4
215
250
300
10.5
11.2
dn
e1
80
8.1
85
80
8.1
100
8.4
85
80
95
150
200
XINXING PIPES
8.7
9.1
9.8
Unit:mm
Body
DN
125
216
Branch
DN
Branch
L
dn
e1
85
155
200
9.8
250
8.1
95
180
250
10.5
260
100
8.4
95
210
300
11.2
265
85
80
8.1
105
240
350
11.9
265
95
100
8.4
110
270
400
12.6
270
110
125
8.7
110
90
80
8.1
265
85
80
8.1
120
100
100
8.4
265
100
100
8.4
120
125
125
8.7
265
115
125
8.7
120
130
150
9.1
265
130
150
9.1
125
155
200
9.8
270
90
80
8.1
145
185
250
10.5
285
100
100
8.4
145
215
300
11.2
290
115
125
8.7
145
240
350
11.9
290
130
150
9.1
150
270
400
12.6
290
160
200
9.8
155
300
450
13.3
300
400
450
12.6
13.3
11.9
400
12.6
90
80
8.1
170
100
80
8.1
295
100
100
8.4
170
115
100
8.4
295
115
125
8.7
170
125
125
8.7
295
130
150
9.1
175
140
150
9.1
295
160
200
9.8
180
165
200
9.8
300
190
250
10.5
190
190
250
10.5
310
95
80
8.1
190
220
300
11.2
315
105
100
8.4
195
245
350
11.9
315
120
125
8.7
225
270
400
12.6
315
130
150
9.1
200
300
450
13.3
315
160
200
9.8
205
330
500
14
330
190
250
10.5
210
90
80
8.1
345
220
300
11.2
220
100
100
8.4
345
90
80
8.1
215
125
125
8.7
345
100
100
8.4
215
130
150
9.1
345
125
150
9.1
215
160
200
9.8
350
150
200
9.8
220
190
250
10.5
360
180
250
10.5
235
215
300
11.2
365
210
300
11.2
235
245
350
11.9
365
240
350
11.9
240
275
400
12.6
365
85
80
8.1
240
305
450
13.3
365
95
100
8.4
240
335
500
14
375
120
125
8.7
250
390
600
15.4
390
125
150
9.1
250
500
600
14
15.4
217
250
300
350
10.5
11.2
11.9
Body
DN
dn
e1
80
8.1
165
80
8.1
100
8.4
165
80
180
125
150
200
250
218
Branch
XINXING PIPES
8.7
9.1
9.8
10.5
Unit:mm
DN
Branch
L
dn
e1
165
235
150
9.1
355
8.1
175
450
200
9.8
350
100
8.4
180
250
250
10.5
345
200
80
8.1
190
275
300
11.2
370
200
100
8.4
195
450
350
11.9
360
200
125
8.7
200
330
400
12.6
390
220
80
8.1
205
360
100
8.4
400
220
100
8.4
210
380
125
8.7
390
220
125
8.7
215
450
150
9.1
450
220
150
9.1
220
235
200
9.8
370
260
80
8.1
235
475
250
10.5
375
260
100
8.4
240
265
300
11.2
375
220
125
8.7
240
285
350
11.9
400
260
150
9.1
250
475
400
12.6
375
260
200
9.8
260
345
450
13.3
420
200
80
8.1
265
370
100
8.4
430
400
450
500
400
12.6
13.3
14
12.6
350
100
8.4
275
395
125
8.7
420
240
125
8.7
280
430
150
9.1
450
240
150
9.1
280
475
200
9.8
475
350
200
9.8
325
500
250
10.5
400
350
250
10.5
350
500
300
11.2
400
210
100
8.4
295
500
350
11.9
400
400
125
8.7
300
500
400
12.6
400
240
150
9.1
300
500
450
13.3
400
250
200
9.8
310
500
500
14
400
400
250
10.5
350
500
100
8.4
500
310
300
11.2
330
500
125
8.7
500
400
100
8.4
400
500
150
9.1
500
220
125
8.7
325
500
200
9.8
500
425
150
9.1
325
500
250
10.5
500
240
200
9.8
325
550
300
11.2
450
265
250
10.5
340
550
350
11.9
450
425
300
11.2
325
550
400
12.6
450
320
350
11.9
360
550
450
13.3
450
340
100
8.4
350
550
500
14
450
425
125
8.7
425
550
600
15.4
450
500
600
14
15.4
219
(35)Socket Spigot Crosses with Double Socket (Refer to Figure 35 and Table 35)
300
400
500
11.2
12.6
14
Table 35 Technical Parameters for Socket Spigot Crosses with Double Socket
340
200
9.8
205
190
370
250
10.5
210
220
400
300
11.2
220
110
290
100
8.4
245
135
315
150
9.1
250
165
345
200
9.8
255
195
375
250
10.5
260
220
400
300
11.2
270
280
460
400
12.6
280
110
310
100
8.4
290
135
335
150
9.1
295
165
365
200
9.8
300
195
395
250
10.5
315
225
425
300
11.2
320
285
485
400
12.6
330
340
540
500
14
340
110
315
100
8.4
350
135
340
150
9.1
355
165
370
200
9.8
360
195
400
250
10.5
365
230
430
300
11.2
370
DN
e1
dn
e2
80
8.1
85
260
80
8.1
85
100
8.4
85
270
80
8.1
95
285
485
400
12.6
380
95
275
100
8.4
95
345
545
500
14
390
85
280
80
8.1
120
400
600
600
15.4
400
100
280
100
8.4
120
130
310
150
9.1
125
90
280
80
8.1
145
100
280
100
8.4
145
130
310
150
9.1
150
160
340
200
9.8
155
90
280
80
8.1
170
100
280
100
8.4
170
130
310
150
9.1
175
160
340
200
9.8
180
190
370
250
10.5
190
105
285
100
8.4
195
130
310
150
9.1
200
150
200
250
300
220
Unit:mm
160
XINXING PIPES
9.1
9.8
10.5
11.2
600
15.4
221
(a)DN300
(b)DN 300
(a)DN300
(b)DN 300
Figure 37 T-Type Socket Plugs
222
Unit:mm
DN
DE
e1
K.R
80
98
16
190
100
118
18
7.2
200
125
144
18
7.5
212
150
170
18
7.8
225
200
222
18
7.2
250
250
274
19.5
9.0
250
300
326
23
9.6
275
350
378
24
10.2
315
275
DN
DN
80
18
600
29.5
565
100
18
700
31
665
125
18
800
33
760
150
18
900
35
860
200
18
1000
37
960
250
19.5
1100
39
1060
400
429
25
10.8
370
275
300
23
1200
41
1160
450
480
26
11.4
420
275
350
24
315
1400
43
1260
500
532
27
12
460
275
400
25
370
1500
44
2362
600
635
29.5
13.2
565
300
450
26
420
1600
45
2715
700
738
30
14.4
660
320
500
27
460
1800
48
3186
800
842
30
15.6
760
330
900
945
30
16.8
860
350
1000
1048
35
18
960
360
1100
1152
35
19.2
1060
380
1200
1255
35
20.4
1160
390
1400
1462
40
22.8
1260
410
1500
1565
40
24
1360
420
1600
1668
40
25.2
1460
450
1800
1875
45
27.6
1560
480
XINXING PIPES
223
DN
224
Unit:mm
size
Bolts
DN
t1
d1
Unit:mm
No. of Bolts/n
PN10
PN16
PN25
PN10
PN16
PN25
PN10
PN16
PN25
70
160
160
160
M16
M16
M16
100
70
180
180
190
M16
M16
M20
M20
150
75
240
240
250
M20
M20
M24
M20
200
75
295
295
310
M20
M20
M24
15
M24
250
90
350
355
370
M20
M24
M27
50
15
M24
300
90
400
410
430
M20
M24
M27
134
50
20
M24
350
100
460
470
490
M20
M24
M30
429
134
50
20
M27
400
100
515
525
550
M24
M27
M33
450
480
134
50
20
10
M27
450
100
565
585
600
10
10
10
M24
M27
M33
500
532
154
55
25
10
M30
500
114
620
650
660
10
10
10
M24
M30
M33
600
635
174
60
25
10
M33
600
114
725
770
770
10
10
10
M27
M33
M36
700
738
184
70
30
12
M33
700
130
840
840
875
12
12
12
M27
M33
M39
800
842
184
70
30
12
M36
800
130
950
950
990
12
12
12
M30
M36
M45
900
945
214
85
30
14
M36
900
130
1050
1050
1050
14
14
14
M30
M36
M45
1000
1048
244
92
30
14
M39
1000
130
1160
1170
1160
14
14
14
M33
M39
M52
1200
1255
274
107
30
16
M45
1200
130
1380
1390
1380
16
16
16
M36
M45
M52
1400
1462
360
96
15
18
M24
1400
150
1590
1590
1640
18
18
18
M39
M45
M56
1500
1565
470
118
25
18
M52
1500
170
1700
1710
18
18
M39
M52
1600
1668
485
120
30
20
M45
1600
180
1820
1820
20
20
M45
M52
d1
DIA
80
98
96
40
15
M16
80
100
118
96
40
15
M16
150
170
96
40
15
200
222
96
46
15
250
274
116
50
300
326
116
350
378
400
XINXING PIPES
225
Unit:mm
Unit:mm
DN
DN
PN10
PN16
PN25
PN40
80
170
120
800
980
380
80
200
200
210
210
100
190
130
900
1095
415
100
200
200
220
220
150
260
150
1000
1210
450
150
200
200
230
230
200
300
180
1200
1440
520
200
220
220
230
240
250
350
200
1400
1670
590
250
220
230
250
260
300
420
250
1600
1900
660
300
220
250
250
280
350
550
250
1800
2130
730
350
230
260
270
290
400
550
250
2000
2360
800
400
230
270
280
340
450
620
260
2200
2588
800
450
250
270
280
340
500
680
300
2400
2756
800
500
260
280
300
380
600
780
300
2600
3000
900
600
260
300
320
390
700
865
345
700
335
335
335
800
335
335
335
900
355
355
355
1000
355
355
355
1200
375
375
375
1400
380
380
1500
450
450
1600
450
450
DN
226
XINXING PIPES
227
(42)Flange
1400
1675
1590
1530
1462
46
32
20
43
M39
36
1500
1786
1700
1640
1565
47.5
33
20
43
M39
36
1600
1915
1820
1750
1668
49
34.5
20
49
M45
40
1800
2115
2020
1950
1875
52
36.5
20
49
M45
44
2000
2325
2230
2150
2082
55
38.5
20
49
M45
48
228
DN
D1
D2
D3
DE
80
200
160
132
98
19
15
100
220
180
156
118
19
150
285
240
211
170
19
200
340
295
266
222
250
400
350
319
300
455
400
350
505
400
Unit:mm
bolt holes
d
Specification
19
M16
15
19
M16
15
23
M20
20
16
23
M20
274
22
17.5
10
23
M20
12
370
326
24.5
19.5
10
23
M20
12
460
429
378
24.5
19.5
10
23
M20
16
565
515
480
429
24.5
19.5
10
28
M24
16
450
615
565
530
480
24.5
20.5
12
28
M24
20
500
670
620
582
532
26.5
21
12
28
M24
20
600
780
725
682
635
30
24
12
31
M27
20
700
895
840
794
738
32.5
23
16
31
M27
24
800
1015
950
901
842
35
24.5
16
34
M30
24
900
1115
1050
1001
945
37.5
26.5
16
34
M30
28
1000
1230
1160
1112
1048
40
28
16
37
M33
28
1100
1340
1270
1218
1152
42.5
30
20
37
M33
32
1200
1455
1380
1328
1255
45
31.5
20
40
M36
32
XINXING PIPES
DN
D1
D2
D3
DE
80
200
160
132
98
19
15
100
220
180
156
118
19
150
285
240
211
170
19
200
340
295
266
222
250
400
355
319
300
455
410
350
520
400
Unit:mm
bolt holes
d
Specification
19
M16
15
19
M16
15
23
M20
20
16
23
M20
12
274
22
17.5
10
28
M24
12
370
326
24.5
19.5
10
28
M24
12
470
429
378
26.5
21
10
28
M24
16
580
525
480
429
28
22.5
10
31
M27
16
450
640
585
548
480
30
24
12
31
M27
20
500
715
650
609
532
31.5
25
12
34
M30
20
600
840
770
720
635
36
29
12
37
M33
20
700
910
840
794
738
39.5
27.5
16
37
M33
24
800
1025
950
901
842
43
30
16
40
M36
24
900
1125
1050
1001
945
46.5
32.5
16
40
M36
28
1000
1255
1170
1112
1048
50
35
16
43
M39
28
1100
1355
1270
1218
1152
53.5
37.5
20
43
M39
32
1200
1485
1390
1328
1255
57
40
20
49
M45
32
1400
1685
1590
1530
1462
60
42
20
49
M45
36
1500
1820
1710
1640
1565
62.5
43
20
56
M52
36
1600
1930
1820
1750
1668
65
45.5
20
56
M52
40
1800
2130
2020
1950
1875
70
49
20
56
M52
44
2000
2345
2230
2150
2082
75
52.5
20
62
M56
48
229
DN
D1
D2
D3
DE
80
200
160
132
98
19
15
100
235
190
156
118
19
150
300
250
211
170
20
200
360
310
274
222
250
425
370
330
300
485
430
350
555
400
Unit:mm
bolt holes
d
Specification
19
M16
15
23
M20
16
28
M24
22
17.5
28
M24
12
274
24.5
19.5
10
31
M27
12
389
326
27.5
22
10
31
M27
16
490
448
378
30
24
10
34
M30
16
620
550
503
429
32
25.5
10
37
M33
16
450
670
600
548
480
34.5
27.5
12
37
M33
20
500
730
660
609
532
36.5
29
12
37
M33
20
600
845
770
720
635
42
33.5
12
40
M36
20
700
960
875
820
738
46.5
32.5
16
43
M39
24
800
1085
990
928
842
51
35.5
16
49
M45
24
900
1185
1090
1028
945
55.5
39
16
49
M45
28
1000
1320
1210
1140
1048
60
42
16
56
M52
28
1100
1420
1310
1240
1152
64.5
45
20
56
M52
32
1200
1530
1420
1350
1255
69
48.5
20
56
M52
32
1400
1755
1640
1560
1462
74
52
20
62
M56
36
1600
1975
1860
1780
1668
81
56.5
20
62
M56
40
1800
2195
2070
1985
1875
88
61.5
20
70
M64
44
2000
2425
2300
2210
2082
95
66.5
20
70
M64
48
DN
D1
D2
D3
DE
80
200
160
132
98
19
15
100
235
190
156
118
19
150
300
250
211
170
26
200
375
320
284
222
250
450
385
345
300
515
450
350
580
400
Unit:mm
bolt holes
d
Specification
19
M16
15
23
M20
18
28
M24
30
21
31
M27
12
274
34.5
24
10
34
M30
12
409
326
39.5
27.5
10
34
M30
16
510
465
378
44
31
10
37
M33
16
660
585
535
429
48
33.5
10
40
M36
16
450
685
610
560
480
50
35
12
40
M36
20
500
755
670
615
532
52
36.5
12
43
M39
20
600
890
795
735
635
58
40.5
12
49
M45
20
(43)Welded-on Flange
230
XINXING PIPES
231
232
Unit:mm
Unit:mm
DN
D1
D2
D3
D4
D5
D6
DN
D1
D2
D3
D4
D5
D6
80
220
160
132
98
112
118
19
19
50
80
220
160
132
98
112
118
19
19
50
100
220
180
156
118
133
139
19
19
60
100
220
180
156
118
133
139
19
19
60
125
250
210
170
144
158
164
19
19
60
125
250
210
170
144
158
164
19
19
60
150
285
240
211
170
186
192
19
23
60
150
285
240
211
170
186
192
19
23
60
200
340
295
266
222
240
246
20
23
64
200
340
295
266
222
240
246
20
23
12
64
250
400
350
319
274
294
300
22
23
12
10
64
250
400
355
319
274
294
300
22
28
12
10
64
300
455
400
370
326
346
352
24.5
23
12
10
74
300
455
410
370
326
346
352
24.5
28
12
10
74
350
505
460
429
378
400
408
24.5
23
16
10
74
350
520
470
429
378
400
408
26.5
28
16
10
74
400
565
515
480
429
451
459
24.5
28
16
10
80
400
580
525
480
429
451
459
28
31
16
10
80
450
615
565
530
480
500
506
24.5
28
20
12
80
450
640
585
548
480
500
506
30
31
20
12
86
500
670
620
582
532
552
558
26.5
28
20
12
86
500
715
650
609
532
552
558
31.5
34
20
12
91
600
780
725
682
635
655
663
30
31
20
12
96
600
840
770
720
635
655
663
36
37
20
12
100
700
895
840
794
738
760
768
32.5
31
24
12
98
700
910
840
794
738
760
768
39.5
37
24
12
105
800
1015
950
901
842
866
876
35
34
24
12
100
800
1025
950
901
842
866
876
43
40
24
12
108
900
1115
1050
1001
945
971
981
37.5
34
28
12
103
900
1125
1050
1001
945
971
981
46.5
40
28
12
112
1000
1230
1160
1112
1048
1076
1086
40
37
28
12
120
1000
1255
1170
1112
1048
1076
1086
50
43
28
12
130
1100
1340
1270
1218
1152
1180
1190
42.5
37
32
12
123
1100
1355
1270
1218
1152
1180
1190
53.5
43
32
12
134
1200
1455
1380
1328
1255
1285
1295
45
40
32
15
128
1200
1485
1390
1328
1255
1285
1295
57
49
32
15
138
1400
1675
1590
1530
1462
1496
1512
46
43
36
15
138
1400
1685
1590
1530
1462
1496
1512
60
49
36
15
152
1500
1785
1700
1640
1565
1601
1617
47.5
43
36
15
140
1500
1820
1710
1640
1565
1601
1617
62.5
56
36
15
155
1600
1915
1820
1750
1668
1706
1722
49
49
40
15
142
1600
1930
1820
1750
1668
1706
1722
65
56
40
15
158
1800
2115
2020
1950
1875
1917
1933
52
49
44
15
145
1800
2130
2020
1950
1875
1917
1933
70
56
44
15
163
2000
2325
2230
2150
2082
2126
2136
55
49
48
15
148
2000
2345
2230
2150
2082
2126
2136
75
62
48
15
168
XINXING PIPES
233
234
Unit:mm
DN
D1
D2
D3
D4
D5
D6
80
220
160
132
98
112
118
19
19
50
100
235
190
156
118
133
139
19
23
60
125
270
220
184
144
158
164
19
28
60
150
300
250
211
170
186
192
20
28
60
200
360
310
274
222
239
245
22
28
12
62
250
425
370
330
274
294
300
24.5
31
12
10
63.5
300
485
430
389
326
346
352
27.5
31
16
10
73
350
555
490
448
378
398
408
30
34
16
10
76
400
620
550
503
429
449
459
32
37
16
10
78
450
670
600
548
480
500
510
34.5
37
20
12
81
500
730
660
609
532
552
562
36.5
37
20
12
83
600
845
770
720
635
655
665
42
40
20
12
90
700
960
875
820
738
760
776
46.5
43
24
12
95
800
1085
990
928
842
866
886
51
49
24
15
100
900
1185
1090
1028
945
971
991
55.5
49
28
15
105
1000
1320
1210
1140
1048
1076
1096
60
56
28
15
110
1100
1420
1310
1240
1152
1180
1200
64.5
56
32
15
115
1200
1530
1420
1350
1255
1285
1305
69
56
32
15
120
1400
1755
1640
1560
1462
1496
1516
74
62
36
15
125
1500
1865
1750
1678
1565
1601
1625
77.5
62
36
15
130
1600
1975
1860
1780
1668
1706
1726
81
62
40
15
132
1800
2195
2070
1985
1875
1917
1937
88
70
44
15
139
2000
2425
2300
2210
2082
2126
2150
95
70
48
15
188
XINXING PIPES
PN10
Unit:mm
PN16
PN25
DN
D1
D2
D1
D2
D1
D2
80
220
98
16
220
98
16
220
98
16
100
220
118
16
220
118
16
235
118
16
125
250
144
16
250
144
16
270
144
16
150
285
170
16
285
170
16
300
170
17
200
340
222
17
340
222
17
360
222
19
250
400
274
19
400
274
19
425
274
21.5
300
455
326
20.5
455
326
20.5
485
326
23.5
350
505
378
20.5
520
378
22.5
555
378
26
400
565
429
20.5
580
429
24
620
429
28
450
615
480
20.5
640
480
26
670
480
30.5
500
670
532
22.5
715
532
27.5
730
532
32.5
600
780
635
25
840
635
31
845
635
37
700
895
738
27.5
910
738
34.5
960
738
41.5
800
1015
842
30
1025
842
38
1085
842
46
235
900
1115
945
32.5
1125
945
41.5
1185
945
50.5
1000
1230
1048
35
1255
1048
45
1320
1048
55
1100
1340
1152
37.5
1355
1152
48.5
1420
1152
59.5
1200
1455
1255
40
1485
1255
52
1530
1255
64
1400
1675
1462
41
1685
1462
55
1755
1462
69
1500
1785
1565
42.5
1820
1565
57.5
1865
1565
72.5
1600
1915
1668
44
1930
1668
60
1975
1668
76
1800
2115
1875
47
2130
1875
65
2195
1875
83
2000
2325
2082
50
2345
2082
70
2425
2082
90
(45)Blank Flanges
Unit:mm
DN
80
200
19
16
100
220
19
16
125
250
19
16
150
285
19
16
200
340
20
17
250
400
22
19
300
455
24.5
20.5
350
505
24.5
20.5
325
400
565
24.5
20.5
375
450
615
25.5
21.5
425
500
670
26.5
22.5
475
600
780
30
25
575
700
895
32.5
27.5
675
800
1015
35
30
775
900
1115
37.5
32.5
875
1000
1230
40
35
975
1100
1340
42.5
37.5
1075
1200
1455
45
40
1175
1400
1675
46
41
1375
1500
1786
47.5
42.5
1475
1600
1915
49
44
1575
1800
2115
52
47
1775
2000
2325
55
50
1975
(a) DN300
(b) DN>300
236
XINXING PIPES
Unit:mm
DN
80
200
19
16
100
220
19
16
125
250
19
16
150
285
19
16
200
340
20
17
250
400
22
19
300
455
24.5
20.5
350
520
26.5
22.5
325
237
400
580
28
24
375
450
640
30
26
425
500
715
31.5
27.5
475
600
840
36
31
575
700
910
39.5
34.5
675
800
1025
43
38
775
900
1125
46.5
41.5
875
1000
1255
50
45
975
1100
1355
53.5
48.5
1075
1200
1485
57
52
1175
1400
1685
60
55
1375
1500
1820
62.5
57.5
1475
1600
1930
65
60
1575
1800
2130
70
65
1775
2000
2345
75
70
1975
(46)Reducing Flanges
Unit:mm
Table 53 Technical Parameters for Reducing Flanges (PN10)
238
Unit:mm
DN
80
200
19
16
DNdn
D1
D2
D3
D4
D5
D6
n1
n2
100
235
19
16
20080
340
295
118
84
160
200
23
16
39
125
270
19
16
200100
340
295
144
104
180
220
23
16
39
150
300
20
17
25080
400
350
118
84
160
200
12
23
16
41
200
360
22
19
250100
400
350
148
104
180
220
12
23
16
41
250
425
24.5
21.5
250150
400
350
200
154
240
285
12
23
20
43
300
485
27.5
23.5
350
555
30
26
325
30080
455
400
118
84
160
200
12
23
16
44
400
620
32
28
375
300100
455
400
148
104
180
220
12
23
16
44
450
670
34.5
30.5
425
300150
455
400
200
154
240
285
12
23
20
44
500
730
36.5
32.5
475
300200
455
400
250
205
295
340
12
23
20
45
600
845
42
37
575
35080
505
460
118
84
160
200
16
23
16
44
700
960
46.5
41.5
675
350100
505
460
148
104
180
220
16
23
16
44
800
1085
51
46
775
350150
505
460
203
155
240
285
16
23
20
44
900
1185
55.5
50.5
875
350200
505
460
250
205
295
340
16
23
20
44
1000
1320
60
55
975
350250
505
460
303
254
350
400
16
12
23
20
47
1200
1530
69
64
1075
40080
565
515
118
84
160
200
16
28
16
44
1400
1755
74
69
1175
400100
565
515
148
104
180
220
16
28
16
44
1600
1975
81
76
1375
1800
2195
88
83
1475
400150
565
515
205
155
240
285
16
28
20
44
2000
2425
95
90
1575
XINXING PIPES
239
240
400200
565
515
270
205
295
340
16
28
20
45
400250
565
515
303
254
350
400
16
12
28
20
47
400300
565
515
354
309
400
455
16
12
28
20
49
50080
670
620
118
84
160
200
20
28
16
46
500100
670
620
148
104
180
220
20
28
16
46
500150
670
620
203
155
240
285
20
28
20
46
500200
670
620
250
205
295
340
20
28
20
47
500250
670
620
303
254
350
400
20
12
28
20
49
500300
670
620
354
309
400
455
20
12
28
20
51
500350
670
620
409
354
460
505
20
16
28
20
51
500400
670
620
464
409
515
565
20
16
28
24
51
60080
780
725
118
84
160
200
20
31
16
49
600100
780
725
148
104
180
220
20
31
16
49
600150
780
725
205
155
240
285
20
31
20
49
600200
780
725
250
205
295
340
20
31
20
50
600250
780
725
303
254
350
400
20
12
31
20
52
600300
780
725
354
309
400
455
20
12
31
20
55
600350
780
725
409
354
460
505
20
16
31
20
55
600400
780
725
464
409
515
565
20
16
31
24
55
600450
780
725
515
455
565
615
20
20
31
24
55
80080
1015
950
118
84
160
200
24
34
16
54
800100
1015
950
148
104
180
220
24
34
16
54
800150
1015
950
205
155
240
295
24
34
20
54
800200
1015
950
250
205
295
340
24
34
20
55
800250
1015
950
303
254
350
400
24
12
34
20
57
800300
1015
950
354
309
400
455
24
12
34
20
60
800350
1015
950
409
354
460
505
24
16
34
20
60
800400
1015
950
464
409
515
565
24
16
34
24
60
800450
1015
950
515
455
565
615
24
20
34
24
60
800500
1015
950
566
508
620
670
24
20
34
24
62
800600
1015
950
670
608
725
780
24
20
34
27
65
XINXING PIPES
Unit:mm
DNdn
D1
D2
D3
D4
D5
D6
n1
n2
20080
340
295
118
84
160
200
12
23
16
39
200100
340
295
144
104
180
220
12
23
16
39
25080
400
355
118
84
160
200
12
28
16
41
250100
400
355
148
104
180
220
12
28
16
41
250150
400
355
200
154
240
285
12
28
20
43
30080
455
410
118
84
160
200
12
28
16
44
300100
455
410
148
104
180
220
12
28
16
44
300150
455
410
200
154
240
285
12
28
20
44
300200
455
410
250
205
295
340
12
12
28
20
45
35080
520
470
118
84
160
200
16
28
16
45
350100
520
470
148
104
180
220
16
28
16
45
350150
520
470
203
155
240
285
16
28
20
45
350200
520
470
250
205
295
340
16
12
28
20
46
350250
520
470
303
254
355
400
16
12
28
24
48
40080
580
525
118
84
160
200
16
31
16
47
400100
580
525
148
104
180
220
16
31
16
47
400150
580
525
205
155
240
285
16
31
20
47
400200
580
525
270
205
295
340
16
12
31
20
48
400250
580
525
303
254
355
400
16
12
31
24
50
400300
580
525
354
309
410
455
16
12
31
24
52
50080
715
650
118
84
160
200
20
34
16
50
500100
715
650
148
104
180
220
20
34
16
50
500150
715
650
203
155
240
285
20
34
20
50
500200
715
650
250
205
295
340
20
12
34
20
50
500250
715
650
303
254
350
400
20
12
34
24
52
500300
715
650
354
309
400
455
20
12
34
24
56
500350
715
650
409
354
470
520
20
16
34
24
58
500400
715
650
464
409
525
580
20
16
34
27
60
60080
840
770
118
84
160
200
20
37
16
55
600100
840
770
148
104
180
220
20
37
16
55
600150
840
770
205
155
240
285
20
37
20
55
600200
840
770
250
205
295
340
20
12
37
20
56
241
600250
840
770
303
254
355
400
20
12
37
24
58
400100
620
550
148
104
190
235
16
37
20
51
600300
840
770
354
309
410
455
20
12
37
24
60
400150
620
550
205
155
250
300
16
37
24
52
600350
840
770
409
354
470
520
20
16
37
24
62
400200
620
550
270
205
310
360
16
12
37
24
54
600400
840
770
464
409
525
580
20
16
37
27
64
400250
620
550
303
254
370
425
16
12
37
27
56
600450
840
770
515
455
585
640
20
20
37
27
66
400300
620
550
354
309
430
485
16
16
37
27
60
80080
1025
950
118
84
160
200
24
40
16
62
50080
730
660
118
84
160
200
20
37
16
55
800100
1025
950
148
104
180
220
24
40
16
62
500100
730
660
148
104
190
235
20
37
20
55
800150
1025
950
205
155
240
295
24
40
20
62
500150
730
660
203
155
250
300
20
37
24
56
800200
1025
950
250
205
295
340
24
12
40
20
63
500200
730
660
250
205
310
360
20
12
37
24
58
800250
1025
950
303
254
355
400
24
12
40
24
65
500250
730
660
303
254
370
425
20
12
37
27
61
800300
1025
950
354
309
410
455
24
12
40
24
67
500300
730
660
354
309
430
485
20
16
37
27
64
800350
1025
950
409
354
470
520
24
16
40
24
68
500350
730
660
409
354
490
555
20
16
37
30
66
800400
1025
950
464
409
525
580
24
16
40
27
70
500400
730
660
464
409
550
620
20
16
37
33
68
800450
1025
950
515
455
585
640
24
20
40
27
73
60080
845
770
118
84
160
200
20
40
16
61
800500
1025
950
566
508
650
715
24
20
40
30
74
600100
845
770
148
104
190
235
20
40
20
61
800600
1025
950
670
608
770
840
24
20
40
33
79
600150
845
770
205
155
250
300
20
40
24
62
600200
845
770
250
205
310
360
20
12
40
24
64
600250
845
770
303
254
370
425
20
12
40
27
66
600300
845
770
354
309
430
485
20
16
40
27
70
600350
845
770
409
354
490
555
20
16
40
30
72
600400
845
770
464
409
550
620
20
16
40
33
74
600450
845
770
515
455
600
670
20
20
40
33
76
80080
1085
990
118
84
160
200
24
49
16
70
800100
1085
990
148
104
190
235
24
49
20
70
800150
1085
990
205
155
250
300
24
49
24
71
800200
1085
990
250
205
310
360
24
12
49
24
73
800250
1085
990
303
254
370
425
24
12
49
27
75
800300
1085
990
354
309
430
485
24
12
49
27
78
800350
1085
990
409
354
490
555
24
16
49
30
81
800400
1085
990
464
409
550
620
24
16
49
33
83
800450
1085
990
515
455
600
670
24
20
49
33
85
800500
1085
990
566
508
660
730
24
20
49
33
87
800600
1085
990
670
608
770
845
24
20
49
36
93
242
Unit:mm
DNdn
D1
D2
D3
D4
D5
D6
n1
n2
20080
360
310
118
84
160
200
12
28
16
41
200100
360
310
144
104
190
235
12
28
20
41
25080
425
370
118
84
160
200
12
31
16
43
250100
425
370
148
104
190
235
12
31
20
43
250150
425
370
200
154
250
300
12
31
24
44
30080
485
430
118
84
160
200
16
31
16
46
300100
485
430
148
104
190
235
16
31
20
46
300150
485
430
200
154
250
300
16
31
24
47
300200
485
430
250
205
310
360
16
12
31
24
50
35080
555
490
118
84
160
200
16
34
16
49
350100
555
490
148
104
190
235
16
34
20
49
350150
555
490
203
155
250
300
16
34
24
50
350200
555
490
250
205
310
360
16
12
34
24
52
350250
555
490
303
254
370
425
16
12
34
27
54
40080
620
550
118
84
160
200
16
37
16
51
XINXING PIPES
243
L
Figure 48 Bolts for Flange Connection
244
Unit:mm
PN10
PN16
Unit:mm
PN25
PN40
Quantity
ML
Quanti
ML
Quanti
ML
Quanti
ML
80
M1665
M1665
M1665
M1665
1OO
M1665
M1665
M2070
M2070
125
M1665
M1665
M2480
M2480
150
M2070
M2070
M2480
M2490
200
M2070
12
M2070
12
M2480
12
M27100
250
12
M2080
l2
M2490
12
M2790
12
M30110
300
12
M2080
12
M2490
16
M2790
16
M3O120
DN
MK
80
110
260
100
M16
80
100
110
306
120
M16
80
150
130
390
172
M20
90
200
130
430
224
M20
90
250
130
490
276
M20
90
350
16
M2080
l6
M2490
16
M30110
16
M33130
300
130
555
329
M20
100
400
l6
M2490
16
M27100
16
M33120
16
M36140
350
130
610
381
M20
100
450
20
M2490
20
M27100
20
M33120
20
M36150
400
150
660
432
M24
110
500
20
M2490
20
M30110
20
M33120
20
M39150
450
150
725
483
M24
110
600
20
M27l00
20
M33120
20
M36140
20
M45170
500
160
790
535
M24
110
700
24
M27100
24
M33120
24
M39l40
600
165
900
10
638
M27
120
800
24
M30110
24
M36140
24
M45160
700
182
970
10
742
M27
120
900
28
M30120
28
M36140
28
M45170
800
194
1086
10
742
M30
120
1000
28
M33130
28
M39150
28
M52180
900
194
1188
10
949
M30
120
1100
32
M33130
32
M39160
32
M52180
1000
208
1310
10
1053
M33
130
1200
32
M36140
32
M45170
32
M52200
1200
220
1536
10
1260
M36
130
l400
36
M39150
36
M45180
36
M56220
1500
36
M39150
36
M52190
36
M56230
1400
240
1752
10
1468
M39
130
1600
40
M45160
40
M52190
40
M56230
1800
44
M45160
44
M52200
44
M64260
2000
48
M45l70
48
M56220
48
M64270
XINXING PIPES
245
Diameter of
Thread
Unit:mm
65
40
30
16
75
55
36
21.5
75
46
25.6
95
100~600
M20
100
110
700~800
M24
900
120
130
1000
1100
140
1200
85
1400
1500
1600
1800
2000
2200
2400
2600
246
XINXING PIPES
M30
150
160
170
180
90
100
247
Chapter VII
Valves for
Water Supply
and Drainage
Pipeline
248
XINXING PIPES
249
Chapter VII
Valves for
Water Supply
and Drainage
Pipeline
250
XINXING PIPES
251
In the water supply and drainage piping system, the valve is control element, its main function is to isolate
Executive Standard.
the equipment from the piping system, regulate the flow, prevent the backflow, adjust the pressure, etc.
To BS5150/BS5163 btype A
Therefore, whether these functions of valves can be normally realized will influence the normal and safe
water supply of pipeline. When the pipeline is in normal state of water supply, the valve shall be open, so as
to reduce the water head loss; Once the pipeline need to cut off the water flow, the valve should be turned
off rapidly, to realize sound flow-cut. Therefore, valve quality will play a key role in normal operation of
pipeline.
Besides ductile cast iron pipes, fittings and relevant technical services, Xinxing would also provides the
customers with the products required for water supply and drainage piping engineering, such as valves.
Should there be any requirements, please contact with our sales staff.
Component List
Sr-no.
Part name
Material
Body
Ductile iron
Wedge
Stem
Bonnet
Ductile iron
Bearing
Gland
Ductile oiron
0.6
1.0
1.6
2.0
2.5
4.0
DN
50-500
50-500
50-500
50-350
50-300
50-300
Seal test
0.66
1.10
1.76
2.20
2.75
4.40
Seal test
0.90
1.50
2.40
3.00
3.75
6.00
Suotable temperature:-10~80oC
Suotable medium:water, oil, air and weak corrosive fluid etc.
Operation type:Square head or handwreel,wormgear,pneumatic,electric
252
XINXING PIPES
253
DN
PN
D1
D2
D3
0.6
320
280
n-d
254
22
8-19
340
295
266
20
345
298.5
270
28.5
8-22
2.5
360
310
274
22
12-28
375
320
284
30
12-31
0.6
375
335
309
24
12-19
395
350
319
22
12-23
355
319
22
12-28
362
324
30
12-26
24.5
12-31
34.5
12-34
1
200
250
DN
PN
D1
D2
D3
0.6
140
110
88
165
125
99
1
50
1.6
2
2.5
4
0.6
1
80
1.6
2
2.5
4
0.6
1
100
1.6
2
2.5
4
0.6
1
150
1.6
2
2.5
4
254
XINXING PIPES
178
n-d
16
4-14
19
4-19
155
12.5
92
16
4-18
165
125
99
19
4-19
190
150
124
18
4-19
200
160
132
190
152.5
127
200
160
132
210
170
144
220
180
156
4230
190.5
235
216
19
8-19
19
4-19
19
8-19
18
4-19
19
8-19
157
24
8-18
190
156
19
8-23
265
225
199
20
8-19
285
240
211
19
8-23
280
300
241.5
250
216
211
203
283
229
305
267
267
25.5
20
403
26
8-22
H1
82
H2
210
300
1.6
1.6
2
105
260
400
450
115
305
500
292
419
330
12-23
425
370
330
450
385
345
0.6
440
395
363
24
12-23
445
400
370
24.5
12-23
1.6
460
410
370
24.5
12-28
432
381
32
12-26
430
389
27.5
18-01
39.5
16-34
26
12-23
24.5
16-23
26.5
16-28
485
457
356
502
515
450
409
0.6
490
445
413
505
460
429
1.6
520
470
429
535
476
413
35
12-29.5
0.0
540
495
403
26
16-23
565
515
480
24.5
16-28
1.6
580
525
480
28
16-31
0.0
595
550
518
26
16-23
615
565
530
25.5
20-28
1.6
640
585
548
30
20-31
0.6
645
600
568
30
20-23
670
620
582
26.5
20-28
1.6
715
650
609
31.5
20-34
381
406
432
457
H1
H2
175
485
200
575
230
650
260
750
290
845
315
930
345
100
8-23
2.5
2.5
350
405
390
8-28
255
Component list
Sr.no
Parts name
Material
Upper shaft
SS420
Shaft bearing
Al-bronze
Body
Ductile iron
Seat ring
EPDM/NBR/VITON
Disc
Ductile iron
Retainer ring
SS304
SS304
Lower shaft
SS420
Executive Standard.
Pressure:PN6-PN40
Suitable temperature:-10-120
256
DN
150
210
170
200
40
22
70
200
230
197
233
45
30
250
250
223
261
60
30
300
270
251
295
70
350
290
294
330
400
310
329
450
330
500
unit:mm
top works
bot hole dia
holes nes
ISO5211
90
F07
102
125
12
F10
102
125
12
F10
40
12
125
150
14
F12
80
40
12
125
150
14
F12
386
90
50
14
140
175
18
F14
365
411
100
50
14
140
175
18
F14
350
394
445
90
65
18
165
210
22
F16
Sr.no
Component
Sr.no
Component
600
390
454
519
120
65
18
165
210
22
F16
Top flange
Retainer ring
700
430
537
585
100
85
22
254
300
18
F25
Upper shaft
Disc
800
470
593
641
120
85
22
254
300
18
F25
O ring
10
Shaft bearing
900
510
657
706
125
90
25
254
300
18
F25
Shaft bearing
11
O ring
1000
550
722
771
125
100
28
254
300
18
F25
O ring
12
Shaft cover
120
630
845
893
155
120
32
298
350
22
F30
Body
13
1400
710
967
1019
155
120
32
356
415
33
F35
Seat
14
Key
1600
790
1113
1111
198
150
36
406
475
39
F40
1800
870
1251
1244
333
128
32
406
475
39
12
F48
2000
950
1340
1330
400
170
40
483
560
39
12
F48
2200
1000
1420
1450
400
200
45
483
560
39
12
F48
XINXING PIPES
257
Dimensions/PN16
DN
150
210
167
200
40
22
70
200
230
197
233
55
30
250
250
224
282
60
40
300
270
267
313
80
350
290
303
357
400
310
339
450
330
500
unit:mm
top works
DN
holes nes
ISO5211
90
F07
150
210
186
225
60
40
12
136
102
125
12
F10
200
230
235
260
55
40
12
12
125
150
14
F12
250
250
260
307
70
50
40
12
125
150
14
F12
300
270
285
340
95
90
50
14
140
175
18
F14
350
290
320
382
396
110
50
14
140
175
18
F14
400
310
402
379
443
100
65
18
165
210
22
F16
450
330
350
404
469
120
65
18
165
210
22
F16
500
600
390
486
545
120
85
22
254
300
18
F25
700
430
537
590
120
85
22
254
300
18
F25
800
470
606
655
140
90
25
254
300
18
F25
900
510
699
711
150
100
28
298
350
22
F30
1000
550
776
791
170
110
28
298
350
22
1200
630
874
921
240
128
32
356
415
33
1400
710
1034
1038
290
170
40
406
475
1600
790
1175
1118
400
170
40
483
1800
820
1320
1335
400
170
40
2000
950
1460
1475
400
200
2200
1000
1650
1665
400
200
ISO5211
160
14
F10
125
150
14
F12
14
140
175
18
F14
50
14
140
175
18
F14
90
65
18
165
210
22
F16
435
140
65
18
210
260
22
F25
390
470
105
85
22
254
300
18
F25
350
476
496
170
95
25
298
350
22
F30
600
390
517
599
155
100
28
298
350
22
F30
700
430
661
615
244
128
32
406
475
39
F40
800
470
710
780
250
128
32
406
475
39
F40
900
510
760
880
280
128
32
406
475
39
F40
F30
1000
550
820
920
280
185
45
483
560
39
12
F48
F35
1200
630
1077
1174
303
185
45
483
560
39
12
F48
39
F40
1400
710
1100
1220
480
200
45
603
686
39
20
F60
560
39
12
F48
483
560
39
12
F48
45
483
560
39
12
F48
45
483
560
39
12
F48
150
210
188
219
50
30
102
200
230
221
245
80
40
12
250
250
265
280
80
40
300
270
298
312
110
350
290
318
365
400
310
369
450
330
500
unit:mm
top works
bot hole dia
holes nes
ISO5211
125
12
F10
140
175
18
F14
12
140
175
18
F14
50
14
165
210
18
F16
120
55
16
165
210
18
F16
416
120
65
18
165
210
88
F16
375
458
120
65
18
165
210
22
F16
350
420
484
150
85
22
254
300
18
F25
600
390
499
555
170
85
22
254
300
18
F25
Executive Standard.
700
430
601
615
230
100
28
298
350
18
F30
800
470
668
697
230
100
28
356
415
33
F35
900
510
730
750
200
125
32
356
415
33
F35
1000
550
819
828
321
140
36
406
475
39
F40
1200
630
995
1004
260
170
40
483
560
39
12
F48
1400
710
1150
1124
279
170
40
483
560
39
12
F4
XINXING PIPES
top works
holes nes
DN
unit:mm
Dimensions/PN25
258
Dimensions/PN40
Face to face length acc.to ISO 5752 series 13(EN558-1 series 13)
Flange dimensions and drilling acc. to ISO7005-2(EN 1092-2,DIM2501)
259
Dimensions/PN10
Component List
Sr.no
Parts name
Material
Upper shaft
SS420
Shaft bearing
Al-bronze
Body
Ductile iron
Seat ring
EPDM/NBR/VITON
Disc
Ductile iron
Retainer ring
SS304
Lower Shaft
SS420
DN
150
140
156
232
40
22
70
200
152
190
280
45
30
250
165
210
308
60
30
300
178
240
355
70
350
190
274
390
400
216
308
450
222
500
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
100
F07
102
125
12
F10
102
125
12
F10
40
12
125
150
14
F12
80
40
12
125
150
14
F12
446
90
50
14
140
175
18
F14
333
476
100
50
14
140
175
18
F14
229
358
506
90
65
18
165
210
22
F16
600
267
424
586
120
65
18
170
210
22
F16
700
292
480
646
100
85
22
254
300
18
F25
800
318
544
730
12
85
22
254
300
18
F25
900
330
594
790
125
90
25
254
300
18
F25
1000
410
654
880
125
100
28
254
300
18
F25
1200
470
786
1000
155
120
32
298
350
22
F30
1400
530
916
1160
155
128
32
356
415
33
F35
1600
600
1040
1291
198
150
36
406
475
39
F40
1800
670
1160
1450
333
128
32
483
560
39
12
F48
2000
760
1312
1604
400
170
40
483
560
39
12
F48
2200
800
1388
1730
400
200
45
483
560
39
12
F48
2400
900
1620
1924
480
200
45
603
686
39
200
F60
260
XINXING PIPES
261
Dimensions/PN16
DN
150
140
156
232
40
22
70
200
152
190
280
55
30
250
165
220
330
60
40
300
178
248
360
80
350
190
280
420
400
216
312
450
222
500
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
100
F07
102
125
12
F10
12
125
150
14
F12
40
12
125
150
14
F12
90
50
14
140
175
18
F14
454
110
50
14
140
175
18
F14
345
510
100
65
18
165
210
22
F16
229
384
550
120
65
18
165
210
22
F16
600
267
450
620
120
85
22
254
300
18
F25
700
292
494
685
130
85
22
254
300
18
F25
800
318
564
750
140
90
25
254
300
18
F25
900
330
617
846
165
100
28
298
350
22
F30
1000
410
715
915
165
125
32
356
415
33
F35
1200
470
841
1086
240
125
32
356
415
33
F35
1400
530
973
1240
235
160
40
406
475
39
F40
1600
600
1170
1404
400
170
40
483
560
39
12
F48
1800
670
1320
1590
400
170
40
483
560
39
12
F48
2000
760
1460
1730
400
200
45
483
560
39
12
F48
Executive Standard.
Double flanged type
Face to face length acc.to ISO 5752 series 13(EN558-1 series 13)
Flange dimensions and drilling acc. to ISO7005-2(EN 1092-2,DIM2501)
Structure and Technical Parameter
262
XINXING PIPES
Sr.no
Component
Sr.no
Component
Upper shaft
Disc
Top flange
Body
Packing gland
10
Shaft bearing
Shaft bearing
11
O ring
O ring
12
Lower shaft
Seat
13
Key
Retainer ring
263
Component List
Dimensions/PN16
Sr.no
Parts name
Material
Upper shaft
SS420
Shaft bearing
DN
Al-bronze
150
210
167
200
40
22
70
Body
Dl+rubber
200
230
197
233
55
30
Seat ring
EPDM/NBR/VITON
250
250
224
282
60
40
Disc
Dl+rubber
300
270
267
313
80
Retainer ring
SS 316/duplex st.st.
350
290
303
357
Lower Shaft
SS420
400
310
339
450
330
Size:DN100-DN400
500
Pressure:PN6-PN40
Coating:epoxy painting min.thickness200micron
150
210
170
200
40
22
70
200
230
197
233
45
30
250
250
223
261
60
30
300
270
251
295
70
350
290
294
330
400
310
329
450
330
500
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
90
F07
102
125
12
F10
102
125
12
F10
40
12
125
150
14
F12
80
40
12
125
150
14
F12
386
90
50
14
140
175
18
F14
365
411
100
50
14
140
175
18
F14
350
394
445
90
65
18
165
210
22
F16
600
390
454
519
120
65
18
165
210
22
F16
700
430
537
585
100
85
22
254
300
18
F25
800
470
593
641
120
85
22
254
300
18
F25
900
510
657
706
125
90
25
254
300
18
F25
1000
550
722
771
125
100
28
254
300
18
F25
1200
630
845
893
155
120
32
298
350
22
F30
1400
710
967
1019
155
120
32
356
415
33
F35
1600
790
1113
1111
198
150
36
406
475
39
F40
1800
870
1251
1244
333
128
32
406
475
39
12
F48
2000
950
1340
1330
400
170
40
483
560
39
12
F48
2200
1000
1420
1450
400
200
45
483
560
39
12
F48
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
90
F07
102
125
12
F10
12
125
150
14
F12
40
12
125
150
14
F12
90
50
14
140
175
18
F14
396
110
50
14
140
175
18
F14
379
443
100
65
18
165
210
22
F16
350
404
469
120
65
18
165
210
22
F16
600
390
486
545
120
85
22
254
300
18
F25
700
430
537
590
120
85
22
254
300
18
F25
800
470
606
655
140
90
25
254
300
18
F25
900
510
699
711
150
100
28
298
350
22
F30
1000
550
776
791
170
110
28
298
350
22
F30
1200
630
874
921
240
128
32
356
415
33
F35
1400
710
1034
1038
290
170
40
406
475
39
F40
1600
790
1175
1188
400
170
40
483
560
39
12
F48
1800
820
1320
1335
400
170
40
483
560
39
12
F48
2000
950
1460
1475
400
200
45
483
560
39
12
F48
2200
1000
1650
1665
400
200
45
483
560
39
12
F48
264
XINXING PIPES
265
Executive Standard.
Component List
Sr.no
Parts name
Material
Upper shaft
SS420
Packing
Shaft bearing
Al-bronze
Body
Seat
Hard alloy
Disc
WCB
Lower Shaft
SS420
Sr.no
Component
Sr.no
Component
Key
Disc
Upper shaft
Body
Top flange
10
Retainer ring
Packing gland
11
Seat
Packing
12
Shaft bearing
Gasket
13
LOWER SHAFT
Shaft bearing
14
Shaft cover
DN
100
229
130
225
70
30
102
125
254
148
245
75
30
150
267
173
276
95
40
200
292
195
320
98.5
250
330
225
362
300
356
260
350
440
400
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
125
11
F10
102
125
11
F10
12
125
150
14
F12
40
12
125
150
14
F12
121
50
14
140
175
18
F14
400
123
50
14
140
175
18
F14
300
455
130
65
18
165
210
23
F16
500
332
490
130
65
18
165
210
23
F16
450
560
360
540
130
65
18
165
210
23
F16
500
620
400
610
180
80
22
254
300
18
F25
600
800
519
582
178
80
22
254
300
18
F25
700
850
579
632
180
80
22
298
350
23
F30
800
900
640
675
215
100
28
298
350
23
F30
900
1050
704
770
215
100
28
356
415
33
F35
1000
1200
818
895
310
128
32
356
415
33
F35
1200
1500
978
1055
310
128
32
406
475
39
F40
1400
1650
1147
1200
410
170
40
483
560
39
12
F48
1600
1850
1300
1380
460
210
50
603
686
39
20
F60
266
XINXING PIPES
267
Dimensions/PN16
DN
100
229
130
225
70
30
102
125
254
148
245
75
30
150
267
173
276
95
40
200
292
195
320
98.5
250
330
225
362
300
356
260
350
440
400
unit:mm
top works
DN
holes nos
ISO5211
125
11
F10
100
229
130
225
70
30
102
102
125
11
F10
125
254
148
245
75
30
12
125
150
14
F12
150
267
173
276
95
40
40
12
125
150
14
F12
200
292
195
320
98.5
121
50
14
140
175
18
F14
250
330
225
362
400
123
50
14
140
175
18
F14
300
356
260
300
455
130
65
18
165
210
23
F16
350
440
500
332
490
130
65
18
165
210
23
F16
400
450
560
360
540
130
65
18
254
300
18
F25
500
620
400
610
180
80
22
254
300
18
F25
600
800
519
582
214
100
28
298
350
23
F30
700
850
579
786
210
100
28
356
415
33
800
900
790
880
310
128
32
356
415
33
900
1050
805
895
310
128
32
356
415
1000
1200
975
1050
310
128
32
406
1200
1500
1125
1185
410
170
40
1400
1650
1140
1200
410
170
1600
1850
1290
1370
460
210
XINXING PIPES
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
125
11
F10
102
125
11
F10
12
125
150
14
F12
40
12
125
150
14
F12
121
50
14
165
210
23
F16
400
123
50
14
165
210
23
F16
300
455
130
65
18
254
300
18
F25
500
332
490
130
65
18
254
300
18
F25
450
560
365
563
179
80
22
298
350
23
F30
500
620
422
454
175
80
22
298
350
23
F30
600
800
519
582
214
100
28
298
350
23
F30
F35
700
850
579
786
210
100
28
356
415
33
F35
F35
800
900
790
880
310
128
32
356
415
33
F35
33
F35
900
1050
960
1030
310
128
32
406
475
39
F40
475
39
F40
1000
1200
1120
1175
410
170
40
406
475
39
F40
406
475
39
F40
1200
1500
1140
1200
410
170
40
483
560
39
12
F48
40
483
560
39
12
F48
50
603
686
39
20
F60
268
Dimensions/PN25
Dimensions/PN40
DN
100
229
130
225
70
30
102
125
254
148
245
75
30
150
267
173
276
95
40
200
292
195
320
98.5
250
330
225
362
300
356
260
350
440
400
unit:mm
top works
bolt hole dia.
holes nos
ISO5211
125
11
F10
102
125
11
F10
12
125
150
14
F12
40
12
125
150
14
F12
121
50
14
165
210
23
F16
400
123
50
14
165
210
23
F16
300
455
130
65
18
254
300
18
F25
500
350
545
180
80
22
298
350
23
F30
450
560
365
563
180
80
22
298
350
23
F30
500
620
460
520
210
100
28
298
350
23
F30
600
800
565
770
210
100
28
356
415
33
F35
700
850
780
865
310
128
32
356
415
33
F35
800
900
945
1015
310
128
32
406
475
39
F40
900
1050
1100
1155
410
170
40
406
475
39
F40
1000
1200
1140
1200
410
170
40
483
560
39
12
F48
1200
1500
1290
1370
460
210
50
603
686
39
20
F60
269
DN
(mm)
D
PN10
D1
PN16
PN10
D2
PN16
PN10
b
PN16
PN10
PN16
Z-d
PN10
PN16
Executive Standard
50
203
190
165
125
99
19
4-19
65
216
210
185
145
118
19
4-19
80
241
230
200
160
132
19
8-9
100
292
250
220
180
156
19
8-19
125
330
280
250
210
184
19
8-19
150
356
315
285
240
211
19
8-23
200
495
370
340
295
266
20
8-23
12-23
250
622
430
395
405
350
355
319
22
12-23
12-28
24.5
12-23
12-28
270
size(mm)
300
698
475
445
460
400
410
370
Valve Clack
Rubber Assembly
350
787
550
505
520
460
470
429
24.5
26.5
16-23
16-28
400
914
600
565
580
515
525
480
24.5
28
16-28
16-31
450
978
615
640
565
585
530
548
25.5
30
20-28
20-31
500
978
670
715
620
650
582
609
26.5
31.5
20-28
20-34
1.0
1.6
600
1295
780
840
725
770
682
720
30
36
20-31
20-37
1.5
2.4
800
1956
1015
1025
950
950
901
901
35
43
24-34
24-40
1.1
1.76
Working Temperature ( )
80
Working Medium
XINXING PIPES
271
272
XINXING PIPES
273