'%=:HGJHDQFKRU
Anchor version
Benefits
-
well proven
simple installation
small drill bit diameter
reliable setting thanks to simple
visual check
- for fixing in cracked concrete,
redundant fastening only, e.g.
suspended ceilings
DBZ
&DUERQVWHHO
&RQFUHWH
a)
7HQVLOH
a)
]RQH
5HGXQGDQW
IDVWHQLQJ
)LUH
UHVLVWDQFH
(XURSHDQ
7HFKQLFDO
$SSURYDO
&(
FRQIRUPLW\
Approvals / certificates
Description
European technical approval
Fire test report
Assessment report (fire)
a)
Authority / Laboratory
DIBt
DIBt
warringtonfire
a) All data given in this section for DBZ wedge anchor according ETA-06/0179, issue 2011-09-14. The anchor is
to be used only for redundant fastening for non-structural applications.
Basic loading data for all load directions according design method C of ETAG 001
All data in this section applies to
- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Concrete C 20/25 fck,cube = 25 N/mm to C50/60, fck,cube = 60 N/mm
- Anchors in redundant fastening
[kN]
DBZ 6/4,5
DBZ 6/35
6,0
6,0
[kN]
DBZ 6/4,5
DBZ 6/35
4,0
4,0
09 / 2012
DBZ 6/4,5
DBZ 6/35
2,2
2,2
DBZ 6/4,5
DBZ 6/35
1,6
1,6
[kN]
[kN]
With overall partial safety factor for action J = 1,4. The partial safety factors for action depend on the type of
loading and shall be taken from national regulations.
a)
Minimum number
of fixing points
Minimum number
of anchors per fixing point
2 kN
3 kN
The value for maximum design load of actions per fastening point NSd is valid in general that means all
fastening points are considered in the design of the redundant structural system. The value NSd may be
increased if the failure of one (= most unfavourable) fixing point is taken into account in the design
(serviceability and ultimate limit state) of the structural system e.g. suspended ceiling.
Materials
Mechanical properties of DBZ
Anchor size
DBZ 6/4,5
DBZ 6/35
Nominal tensile
strength
f uk
[N/mm]
390
390
Yield strength
fyk
[N/mm]
310
310
Stressed crosssection
As
[mm]
26
26
Char. bending
resistance
[Nm]
5,0
5,0
0
Rk,s
Material
1 Anchor shank
2 Expansion pin
Marking
d1
l1
09 / 2012
l2
309
Anchor dimensions
Anchor size
DBZ 6/4,5
DBZ 6/35
l1
[mm]
2,5
2,5
Max. distance
d1
[mm]
6,4
6,4
[mm]
37,5
68
DBZ 6/4,5
DBZ 6/35
Setting
Recommended installation equipment
Anchor size
Rotary hammer
Other tools
TE 2 TE 7
hammer, blow out pump
Setting instruction
310
09 / 2012
Member thickness
Thickness
of fixture
df
tfix
hef
Anchorage
h1
Setting details
Fixture
e.g. wire
Anchor size
DBZ 6/4,5
Thickness of fixture
tfix [mm]
20 tfix 35
5 tfix < 20
h1 [mm]
40
55
70
d0 [mm]
dcut [mm]
6,4
6,4
df [mm]
DBZ 6/35
4,5
DBZ 6/35
4,5
20 tfix 35
5 tfix < 20
hmin [mm]
80
80
100
hef [mm]
32
32
Critical spacing
scr [mm]
200
200
ccr [mm]
150
150
a)
tfix [mm]
a)
The critical spacing (critical edge distance) shall be kept. Smaller spacing (edge distance) than critical spacing
(critical edge distance) are not covered by the design method.
09 / 2012
311