Metrological setup
All options in this section require INSTALLER level password entry.
Class
/ /
Possible values: II, III and IIII.
Capacity
/ / /
Multi-division:
One area divided into 2 or 3 parts, each with a different division.
$
Multi-range:
2 or 3 ranges, from 0 to its maximum capacity, with different steps.
04-55-00-1 MI
39
i 40 Indicator
Adjustment with depositing a standard weight is the preferred method of adjusting a weighing instrument. This
is the method that leads to the most accurate results.
Zero offset
Put any standard mass placing accessories (for example, the mass suspension device for a hopper) and start
the following command.
/ , /
Zero measurement
As before, the measurement must be made with any standard mass placing accessories, but without any other
load.
/ , / - / -
-
Declaring the number of segments
/ , / - / $$
Most often, it is not necessary to adjust a weighing instrument over several segments. Leave the default
value: NB SEG=1.
If the load receiver provides a not so linear signal and requires a calibration over several segments, enter
the number of segments, for example: NB SEG=3.
Maximum number of segments: 6.
40
04-55-00-1 MI
Linearisation on a segment
/ , / - / "
"$./
"0
$$
Follow the procedure above for each segment, until the maximum number of segments defined in the order of
increasing mass (for example, 3):
/ , / - / %
/ , / - / &
04-55-00-1 MI
41
i 40 Indicator
The adjustment without standard weight can be used alternatively, in various adverse conditions. This is the
case of a weighing instrument that it is not possible to discharge to perform the adjustment (e.g. a silo loaded with
several tonnes of product to be preserved). This method leads to a precision of the order of 1 to 2%.
$
Load supported by sensors when the instrument is unloaded (in system weight unit).
"Downweighing" method
42
.
04-55-00-1 MI
.
.
%1$%!
(i) Value of the mass loaded or unloaded measured using a reference device.
04-55-00-1 MI
43
i 40 Indicator
2%$'!
.
Verification
This option requires INSTALLER level password entry.
/ !
Without exiting the configuration mode, this option allows you to immediately assess the weighing
function, in particular the quality of metrological adjustment.
When the weighing instrument is adjusted to a different place from the point of use, it is necessary to
record the latitude and altitude values of each site. Thus, the system can calculate the compensation of the gravity
difference between the two locations.
So that the compensation for the variation of gravity is effective, the parameters of the instrument's usage location
must be recorded after adjustment.
Record the place of use parameters:
/ /
/
/ /
/
44
04-55-00-1 MI
Initial zero
This reset to zero can be made when the indicator is powered on. To do this, the user starts the indicator
by pressing and holding the and
keys at the same time.
This zero is the reference to other zero devices.
/ / -
-
Limit value below the real zero. For example, to enter a limit at -10%, enter 10.
Possible values: From 0 to -100% of the maximum capacity.
Trade use: From 0 to -20% of the maximum capacity (default value: +/- 5 %)
-
Limit value below the real zero. For example, to enter a limit at -10%, enter 10.
Possible values: From 0 to -100% of the maximum capacity.
Trade use: From 0 to -20% of the maximum capacity (default value: 15 %)
Automatic zero
If enabled, this reset to zero occurs automatically when the gross weight remains stable:
- in a range from 0 to -2 of the maximum capacity from the initial zero;
- during a period greater than or equal to the time.
/ / $-$
Function enabled after the expiration of delay time described below.
Zero tracking
This device allows maintaining the weight at zero when the scale is unloaded.
The action of this reset to zero is limited at the range 0 2% of the maximum capacity from the initial
zero.
/ / -
%'
04-55-00-1 MI
45
i 40 Indicator
Flow correction
This function corrects a slow drift of the indication supplied by the loaded weighing cell.
/ /
Possible values: ACTIVE OR INACTIVE.
Default value: INACTIVE.
Filtering
This function allows reducing the signal disturbance provided by the weighing sensor. A strong filtering
results in longer response times after the removal or addition of a load.
/ /
Possible values: 0 to 4.
Predefined filtering code details.
Filter 1
Filter 2
Filter 3
Code
Frequency
(meas. / s)
Type
Window
Type
Window
Type
Window
50
AVERAGE
10 meas.
AVERAGE
10 meas.
AVERAGE
10 meas.
50
AVERAGE
10 meas.
AVERAGE
10 meas.
SORTING
9 meas.
50
AVERAGE
7 meas.
AVERAGE
6 meas.
AVERAGE
5 meas.
100
AVERAGE
10 meas.
AVERAGE
10 meas.
AVERAGE
8 meas.
Stability
This function allows adjusting the measurement instability range in which it is declared unstable (symbol
present). This only has consequence on the auxiliary devices that are only triggered when stability is
reached (recording in data storage memory, for example).
/ /
Possible values: 0 to 9.
Details of predefined stability codes.
Code
Window
2 meas.
3 meas.
4 meas.
4 meas.
8 meas.
12 meas.
8 meas.
16 meas.
20 meas.
Limit
10 pts
10 pts
10 pts
5 pts
5 pts
7 pts
6 pts
5 pts
5 pts
46
04-55-00-1 MI
In case of need, the default parameters can be re-established, according to three independent categories:
Adjustment, setup and installation.
/ $
The first two options require INSTALLER level password entry.
04-55-00-1 MI
,
47
i 40 Indicator
48
04-55-00-1 MI