PM1
See procedure
IN-32
PM
PM2
PARTS LOCATION
PM
B128129E02
PM3
MULTI-DISPLAY
PM
TELEVISION CAMERA
E128797E02
PM4
SYSTEM DIAGRAM
Multi-display
Television Camera
BK/UP LP
from
GAUGE Fuse
PM
to
Combination Meter
E126419E02
PM5
SYSTEM DESCRIPTION
1.
2.
Item
GENERAL
(a) To assist the driver with parking the vehicle by
displaying an image of the area behind the vehicle,
this system has a television camera mounted on the
luggage compartment door. The system displays
the image on the multi-display.
(b) This system consists of the following components:
(1) Multi-display
(2) Television camera
(c) This system is equipped with a self-diagnosis
system, which is operated on a designated window
that appears on the display panel, just as in the
navigation system.
FUNCTION OF COMPONENTS
(a) The multi-display controls the system by using
information from the following components:
Function
Multi-display
BK/UP LP Relay
3.
4.
OPERATION EXPLANATION
(a) The BK/UP LP relay sends an R position signal to
the multi-display when the shift lever is moved to the
R position. After receiving the R position signal, the
multi-display switches from the navigation system to
the rear view monitor system.
NOTES FOR REAR VIEW MONITOR
(a) Notes for the rear view monitor.
(1) The rear view monitor may not function properly
if subjected to a severe impact by any hard
object.
(2) Do not "scrub" the lens of the camera because it
is made of resin. Scrubbing it may scratch the
cover and affect the image. Prevent organic
solvents, waxes, bond removing solvents, or
glass coating from adhering to the cover. If
anything adheres to the cover, clean it off
immediately and wash the lens with water.
(3) Exposing the camera to a sudden temperature
change may affect proper functioning of the
camera.
(4) A clear image may not appear if the camera is
dirty with snow, mud, etc. In that case, wash it
with water and wipe off the lens. Use a detergent
to remove dirt if necessary.
PM
PM6
PM
PM7
NEXT
NEXT
NEXT
BASIC INSPECTION
(a) Turn the power switch ON (ACC).
(b) Check whether or not the display appears on the multidisplay.
Result
Result
Proceed to
Display appears
Go to NAVIGATION SYSTEM
Proceed to
PM
PM8
Go to step 7
NEXT
7
NEXT
END
PM
PM9
Suspected area
See page
PM-9
PM-12
3. Multi-display
AV-175
PM-12
3. Multi-display
PM-9
2. Multi-display
PM-12
2. Multi-display
PM
PM10
TERMINALS OF ECU
1.
T12
E126420E01
PM
Wiring Color
Terminal
Description
Condition
Specified Condition
W - Body ground
Ground
Always
Below 1
B-W
Power source
Approx. 6 V
Wiring Color
Terminal
Description
Condition
Specified Condition
R - Shielded
Display signal
See waveform 1
GND
Item
Content
Tool Setting
Condition
2.
E119731E01
PM11
WIRING DIAGRAM
Multi-display
to
Rear Combination Lights
BK/UP LP
from
GAUGE Fuse
REV
PM
to
Combination Meter
E126421E04
INSPECTION PROCEDURE
OK
GO TO LIGHTING SYSTEM
PM12
E119736
Display
ON
Except R
OFF
HINT:
This display is updated once per second. As a result, it is
normal for the display to lag behind the actual change in
the switch.
OK
NG
CHECK MULTI-DISPLAY
PM
REV
Tester Connection
Condition
Specified Condition
Power switch is ON
(IG).
Shift lever is moved to
R position.
10 to 14 V
Power switch is ON
(IG).
Shift lever is moved to
any position except R.
Below 1 V
E126484E02
OK
NG
PM13
Multi-display
M13
Tester Connection
Specified Condition
Below 1
10 k or higher
NG
REV
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
E126422E04
OK
PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE
PM
PM14
WIRING DIAGRAM
INSPECTION PROCEDURE
Television Camera
Multi-display
CV+
V+
CGND
CGND
CB+
PM
CA+
CV-
Shielded
V-
Shielded
I102047E02
T12
CV+
CV-
E126485E01
Item
Content
Tester Connection
Tool Setting
Condition
NG
PM15
GND
E119731E02
OK
Multi-display
M14
Tester Connection
V+
V-
CA+
CGND
Television Camera
CV+
CV-
CB+
Below 1
Below 1
Below 1
Below 1
10 k or higher
10 k or higher
10 k or higher
NG
T12
Specified Condition
CGND
E126424E03
OK
PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE
PM