_____________________________________________________________________
Telephone:
(+974) 44337000
Fax:
(+974) 44337100
Email:
bm.fosroc@tadmur-trading .com
CONTENTS
Section 1
Section 2
Method Statement
Section 3
Section 4
Test Reports
Section 5
Approvals
constructive solutions
Thioflex 600
1
2
3
4
5
6
Thioflex 600
Bond breaking tape
Supercast Rearguard S waterstop
Blinding concrete
Membrane
Bitucell*
Chemical resistance to
occasional spillage
Dilute acids
Dilute alkalis
Petrol
Aviation fuels
Diesel fuel
Kerosene
Lubricating oils
Skydrol
White spirit
Chlorinated solvents
Aromatic solvents
Dilute oxidising acids
:
resistant
resistant
resistant
resistant
resistant
resistant
resistant
resistant
resistant
not resistant
not resistant
not resistant
Properties
Form
Movement accommodation
factor (BS 6093)
:
Physical or
chemical change
Pot life
:
:
Setting time
Cure time
Application temperature
Hardness shore 'A' 25C
Water immersion
:
:
:
Biological resistance
Solids content
Density
:
:
Flash point
Flammability
:
:
Estimating
Mixing
Supply
Gun Grade
The base component and curing agent are supplied ready for
mixing in a single tin. Mix thoroughly using a slow speed drill
(300-500 rpm) fitted with a Fosroc Mixing Paddle (MR2) for
5 minutes. Only thorough mixing, including material right at
the bottom of the tin, will result in proper curing. In cold weather
Thioflex 600 mixes more easily if stored overnight at room
temperature.
Immediately after mixing, load the sealant into a Fosroc G
Gun using the follower plate, and apply to the joint.
Pouring Grade
Thioflex 600 Pouring Grade is supplied in two separate
containers. The small container contents should be transferred
to the other tin, and mixed as per the gun grade instructions.
The pouring grade may be poured directly into horizontal joints
or for application to horizontal joints less than 15 mm wide
loaded into a Fosroc G Gun. For quantity application, a Fosroc
1.5 litre gun is available.
Finishing
Thioflex 600 should be tooled to a smooth finish. A minimum
of surface lubricant such as dilute detergent solution may be
used to assist the process. Any masking tape should be
removed immediately after tooling.
Cleaning
Clean equipment immediately after use with Fosroc Solvent 102.
Limitations
-
Thioflex 600 GG
Thioflex 600 PG
Primer 4
Primer 7E
Fosroc solvent 102
:
:
:
:
:
:
:
60 m2/litre
8-10 m2/litre
Coverage
Primer 4
Primer 7E
Litres
Metre run
Metre run
per
per
per
Metre run 2.5 ltr pack 4ltr pack
0.025
100.00
160.00
0.050
50.00
80.00
0.050
50.00
80.00
0.100
25.00
40.00
0.200
12.50
20.00
0.300
8.30
13.30
0.400
6.20
10.00
0.800
3.10
5.00
1.000
2.50
4.00
1.200
2.00
3.30
1.600
1.50
2.50
1.250
2.00
3.20
1.500
1.60
2.64
2.000
1.25
2.00
2.500
1.00
1.60
Metre run
per
5 ltr pack
200.00
100.00
100.00
50.00
25.00
16.60
12.50
6.20
5.00
4.10
3.10
4.00
3.30
2.50
2.00
Additional Information
Precautions
Flash point
Primer 4
Primer 7E
:
:
10C
23C
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the users responsibility to
obtain the recent version.
www.fosroc.com
Head Office
telephone: (+9714) 2039699
email: agf@fosroc.com
Regional offices
Abu Dhabi, Al Gurg Fosroc
email: abudhabi@fosroc.com
telephone: 17738200
telephone: 4817618
fax: 17732828
fax: 4832124
email: bahrain@fosroc.com
email: kuwait@fosroc.com
Oman, Al Amana
Qatar, Tadmur
telephone: 24815080
telephone: 4432365
fax: 24817554
fax: 4419517
email: oman@fosroc.com
email: qatar@fosroc.com
UAE/0300/08/F
Fosroc Primer 7E
Constructive solutions
Precautions
Health and safety
Description
Primer 7E is a two part high performance chemically active,
non-toxic liquid for brush application to prime all concrete,
stone, brickwork, timber and unglazed edges of ceramic tiles.
Advantages
Easy to Apply
Strong adhesion
Disposal
Application
Empty the entire contents of the hardener tin into the base
tin, replace base tin lid. Mix thoroughly until a homogeneous
dispersion is achieved.
Apply one thin coat using a clean dry brush. Avoid over
application of primer causing puddles in the bottom of the
joint. Sealants should be applied between 30 minutes and
4 hours after priming when its tack free.
Do not
Cleaning
Flash point:
Storage life:
12 months
Drying time:
20 to 60 mins.
o
Flash point - Fosroc Solvent 102:
33 C
For further info please contact your local Fosroc office.
Estimating
Supply
Primer 7E:
500 ml can
Coverage
Primer 7E:
8 -10 m2 / ltr
Storage
Shelf life
12 months if stored in the original unopened packs in a cool
dry place. Do not store in direct sunlight.
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation or information given by it.
telephone:
(+9714) 2039699
fax:
(+9714) 2859649
email:
agf@fosroc.com
www.fosroc.com
Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai
UAE/0682/10/A
Page 1
METHOD STATEMENT
method statement
constructive solutions
Thioflex 600
Section A : General Comments
Comments
High temperature working
It is suggested that, for temperatures above 350C, the following guidelines are adopted as
good working practice:
(i)
(ii)
(iii)
Try to avoid application during the hottest times of the day, arrange temporary shading as
necessary.
(iv)
Make sufficient material, plant and labour available to ensure that application is a continuous
process.
Equipment
It is suggested that the following list of equipment is adopted as a minimum requirement
Protective clothing
:
Protective overalls
:
Preparation equipment
Mixing equipment
Application equipment
Al Gurg Fosroc
LLC
Post Box 657, Dubai
United Arab Emirates
telephone:
(+9714) 2039699
fax:
(+9714) 2859649
email:
agf@fosroc.com
www.fosroc.com
Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai
constructive solutions
Section B : Application Method
1.0
Joint Preparation
Refer to the Joint width/depth ratio as per manufacturers instructions in the technical
data sheet.
1.1 The substrate to which Thioflex 600 is bonded must be clean, dry and sound. All arris repairs
should be effected using a Fosroc repair compound.
1.2 Remove all dirt, surface laitence, residual joint former or other contamination from joint faces
by power wire brushing, grinding or grit-blasting. Ensure usage of dry, oil-free compressed air
for blowing all joints. Oil or grease can be removed using Fosroc Joint cleaner.
1.3 All expansion joints must be filled with fillers; tightly packed with no gaps or voids existing at
the base of the sealing slot.
1.4 For construction or contraction joints, a bond breaker or back up tape is recommended, but in
joints where hydrostatic pressure exists, only bond breaking tapes must be used.
2.0
Mixing
The two components of Thioflex 600, supplied in correct mixing proportions, must be
thoroughly mixed for atleast 2 minutes using the recommended Fosroc MR2 mixing
paddle fitted to a slow speed electric drill.
2.1.2
Ensure that the inside of the tin is scraped with a flat bladed tool so that there is no
component on the sides left unmixed.
2.1.3
Mixing should be continued for a further three minutes. The total mixing time is 5
minutes.
The two components of Thioflex 600, supplied in correct mixing proportions, must be
thoroughly mixed for 5 minutes.
2.2.2
Ensure proper mixing of the material right at the bottom of the tin, as it will effect the
curing otherwise.
Page 2 of 4
constructive solutions
3.0
Priming
The substrate to which Thioflex 600 is bonded must be primed with Primer 4.
3.1.2
Apply the primer onto the surface using a brush and leave to dry for 2 to 5 minutes
prior to sealant application.
3.2.2
3.2.2
Apply one thin coat of Primer7E onto the surface using a clean, dry brush, ensuring
complete coverage.
3.2.3
The mixed Thioflex 600 must be applied when the primer is tack free.
3.2.4
Ensure application of Thioflex 600 within 6 hours @ 20C, or 3 hours @ 35C. Repriming is necessary if application is delayed.
4.0
Application
Thioflex 600 must not be used in direct contact with materials containing pitch or bitumen.
4.1 After completion of mixing of the two components, place the single hole follower plate over
the Thioflex and fill directly into a Fosroc Barrel Gun.
4.2 Gun Thioflex 600 firmly into the joint to ensure complete wetting of the bonding surfaces.
4.3 The pouring grade may be poured directly into horizontal joints. For application to horizontal
joints less than 15mm wide, load the Thioflex 600 into a Fosroc G Gun. For quantity
application, a fosroc 1.5litre gun is available.
4.4 Compress and smooth the sealant with a joint shaping tool wetted with a dilute detergent
solution.
4.5 Upon smoothening of the sealant, immediately strip off any masking tape.
Page 3 of 4
constructive solutions
5.0
Cleaning
5.1Clean all equipment immediately after use with Fosroc Solvent 102.
Page 4 of 4
APPLICATION
Joint sealant
SUPPLIER
Fosroc Limited
Drayton Manor Business Park
Coleshill Road
Tamworth
Staffs
B78 3TL
Tel: 01827 262222
Fax: 01827 262444
2 HAZARDS IDENTIFICATION
May cause sensitisation by skin contact. Very toxic to aquatic organisms.
CLASSIFICATION
R43. N;R50.
3 COMPOSITION/INFORMATION ON INGREDIENTS
Name
EC No.
CAS-No.
Content
Classification
287-476-5
085535-84-8
10-30%
N;R50. R53.
40216-08-8
< 1%
215-202-6
1313-13-9
1-5%
Xn;R20/22
205-286-2
137-26-8
< 1%
XYLENE
215-535-7
1330-20-7
< 1%
4 FIRST-AID MEASURES
INHALATION
Remove from exposure - unlikely to occur.
INGESTION
Wash out with water. Do NOT induce vomiting. Obtain medical attention. Beware of asoiration if vomiting occurs.
SKIN CONTACT
Wash thoroughly with soap and water or suitable skin cleanser as soon as possible.
EYE CONTACT
Irrigate immediately with copious quantities of water for several minutes. Obtain medical attention if irrigation persists.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Carbon dioxide, powder, foam or water fog - Do not use water jets.
UNUSUAL FIRE & EXPLOSION HAZARDS
Toxic fumes. For further information see Section 10.
PROTECTIVE MEASURES IN FIRE
Self-contained breathing apparatus.
1/ 4
Std
XYLENE
WEL
LT - ppm
LT - mg/m3
ST - ppm
ST - mg/m3
50 ppm(Sk)
220 mg/m3(Sk)
100 ppm(Sk)
441 mg/m3(Sk)
COLOUR
Pigmented
ODOUR
Mercaptan odour
SOLUBILITY
Insoluble
RELATIVE DENSITY
FLASH POINT (C)
11 TOXICOLOGICAL INFORMATION
INHALATION
Irritating to respiratory system.
INGESTION
Harmful if swallowed. May cause nausea, vomiting and diarrhoea.
SKIN CONTACT
Mildly irritating.
EYE CONTACT
Causes transient irritation.
12 ECOLOGICAL INFORMATION
ECOTOXICITY
Not ecotoxic to fish/daphnia/algae in cured state.
MOBILITY
Insoluble in water.
2/ 4
Not determined
13 DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
Disposal must be in accordance with local and national legislation.
DISPOSAL METHODS
Classified as a special waste. Dispose of through an authorised waste contractor to a licensed site.
14 TRANSPORT INFORMATION
PROPER SHIPPING NAME
UN NO. ROAD
3077
III
IMDG CLASS
III
MARINE POLLUTANT
AIR CLASS
15 REGULATORY INFORMATION
LABELLING
Irritant
CONTAINS
RISK PHRASES
R43
R50
S24
S37
S57
S60
S61
P5
SAFETY PHRASES
EU DIRECTIVES
Dangerous Preparations Directive, 1999/45/EC
STATUTORY INSTRUMENTS
Health & Safety at Work, etc. Act 1974. Environmental Protection Act 1990. Environmental Protection (Duty of Care) Regs.
APPROVED CODE OF PRACTICE
Waste Management. The Duty of Care.
GUIDANCE NOTES
Occupational exposure limits (EH 40).
16 OTHER INFORMATION
3/ 4
Flammable.
R20/21
R20/22
R36/37
R36/38
R38
Irritating to skin.
R40
R43
R50
R51/53
Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
R53
4/ 4
PRIMER 7E BASE
PRODUCT NO.
M2100000AEDXB1
SUPPLIER
EMERGENCY TELEPHONE
MANUFACTURER
2 HAZARDS IDENTIFICATION
Flammable. Harmful by inhalation and in contact with skin. Irritating to eyes and skin. May cause sensitisation by skin contact.
CLASSIFICATION (1999/45)
Xn;R20/21. Xi;R36/38. R43. R10.
ENVIRONMENT
The product contains a substance which is harmful to aquatic organisms and which may cause long term adverse effects in the aquatic
environment.
PHYSICAL AND CHEMICAL HAZARDS
The product is flammable, and heating may generate vapours which may form explosive vapour/air mixtures.
HUMAN HEALTH
In high concentrations, vapours and spray mists are narcotic and may cause headache, fatigue, dizziness and nausea. Harmful by
inhalation and in contact with skin. The product is irritating to eyes and skin.
3 COMPOSITION/INFORMATION ON INGREDIENTS
Name
EC No.
CAS-No.
Content %
Classification (67/548)
25036-25-3
30-60%
Xi;R36,R38. R43.
107-98-2
30-60%
R10 R67
XYLENE
1330-20-7
10-30%
215-535-7
4 FIRST-AID MEASURES
GENERAL INFORMATION
General first aid, rest, warmth and fresh air. Do not give victim anything to drink if they are unconscious. Get medical attention if any
discomfort continues.
1/ 5
PRIMER 7E BASE
INHALATION
Place unconscious person on the side in the recovery position and ensure breathing If respiratory problems, artificial respiration/oxygen.
Get medical attention if any discomfort continues.
INGESTION
Immediately rinse mouth and drink plenty of water or milk. Keep person under observation. Do not induce vomiting. If vomiting occurs, keep
head low. Transport immediately to hospital and bring along these instructions.
SKIN CONTACT
Immediately remove contaminated clothing. Wash off promptly and flush contaminated skin with water. Promptly remove clothing if soaked
through and flush skin with water.
EYE CONTACT
Make sure to remove any contact lenses from the eyes before rinsing. Promptly wash eyes with plenty of water while lifting the eye lids.
Get medical attention promptly if symptoms occur after washing.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Fire can be extinguished using: Water spray, fog or mist. Foam, carbon dioxide or dry powder. Dry chemicals, sand, dolomite etc.
SPECIAL FIRE FIGHTING PROCEDURES
Use pressurised air mask if product is involved in a fire. Cool containers exposed to flames with water until well after the fire is out.
UNUSUAL FIRE & EXPLOSION HAZARDS
Fire causes formation of toxic gases.
PROTECTIVE MEASURES IN FIRE
Self contained breathing apparatus and full protective clothing must be worn in case of fire.
STD
TWA - 8 Hrs
1-METHOXY-2-PROPANOL
WEL
100 ppm
375 mg/m3
150 ppm
560 mg/m3
Sk
XYLENE
WEL
50 ppm
220 mg/m3
100 ppm
441 mg/m3
Sk
2/ 5
STEL - 15 Min
Notes
PRIMER 7E BASE
INGREDIENT COMMENTS
WEL = Workplace Exposure Limits
PROTECTIVE EQUIPMENT
PROCESS CONDITIONS
Provide eyewash station.
ENGINEERING MEASURES
Provide adequate ventilation, including appropriate local extraction, to ensure that the defined occupational exposure limit is not exceeded.
All handling to take place in well-ventilated area.
RESPIRATORY EQUIPMENT
Wear mask supplied with:
Gas cartridge suitable for organic substances.
HAND PROTECTION
Use protective gloves made of: Neoprene. Nitrile. Rubber (natural, latex).
EYE PROTECTION
Wear splash-proof eye goggles to prevent any possibility of eye contact.
OTHER PROTECTION
Wear appropriate clothing to prevent any possibility of skin contact.
HYGIENE MEASURES
DO NOT SMOKE IN WORK AREA! Wash at the end of each work shift and before eating, smoking and using the toilet. Promptly remove
any clothing that becomes contaminated. Use appropriate skin cream to prevent drying of skin. When using do not eat, drink or smoke.
Liquid
COLOUR
Straw
ODOUR
Aromatic.
135-150
1.3-1.4 20 deg C
23 deg C
300
AUTO IGNITION
TEMPERATURE (C)
11 TOXICOLOGICAL INFORMATION
GENERAL INFORMATION
Prolonged and repeated contact with solvents over a long period may lead to permanent health problems.
INHALATION
In high concentrations, vapours may irritate throat and respiratory system and cause coughing. Harmful by inhalation.
INGESTION
Gastrointestinal symptoms, including upset stomach.
3/ 5
PRIMER 7E BASE
SKIN CONTACT
Acts as a defatting agent on skin. May cause cracking of skin, and eczema. Irritating to skin. Harmful in contact with skin. May cause
sensitisation by skin contact.
EYE CONTACT
Irritating and may cause redness and pain.
12 ECOLOGICAL INFORMATION
ECOTOXICITY
Harmful to aquatic organisms, may cause long term adverse effects in the aquatic environment
13 DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
Waste to be treated as controlled waste. Disposal to licensed waste disposal site in accordance with local Waste Disposal Authority.
DISPOSAL METHODS
Dispose of waste and residues in accordance with local authority requirements. Make sure containers are empty before discarding
(explosion risk). Absorb in vermiculite or dry sand and dispose of at a licenced hazardous waste collection point.
14 TRANSPORT INFORMATION
ENVIRONMENTALLY
HAZARDOUS
SUBSTANCE/MARINE
POLLUTANT
UN NO. ROAD
No.
ADR CLASS
III
(D/E)
30
HAZCHEM CODE
3YE
UN NO. SEA
1993
IMDG CLASS
III
EMS
F-E, S-E
UN NO. AIR
1993
AIR CLASS
III
1993
15 REGULATORY INFORMATION
LABELLING
4/ 5
PRIMER 7E BASE
Harmful
CONTAINS
RISK PHRASES
R10
Flammable.
R20/21
R36/38
R43
S25
S26
In case of contact with eyes, rinse immediately with plenty of water and seek medical
advice.
S36/37
S51
S60
SAFETY PHRASES
NATIONAL REGULATIONS
The Chemicals (Hazard Information and Packaging for Supply) Regulations 2002. No. 1689. Workplace Exposure Limits 2005 (EH40)
16 OTHER INFORMATION
GENERAL INFORMATION
The user must be instructed in the proper work procedure and be familiar with the contents of these instructions.
REVISION DATE
25/07/2010
REV. NO./REPL. SDS GENERATED 1
RISK PHRASES IN FULL
R10
Flammable.
R20/21
R36
Irritating to eyes.
R38
Irritating to skin.
R43
R67
DISCLAIMER
The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in
accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using
the product in combination with any other product or any other process is the responsibility of the user.
5/ 5
PRIMER 7E HARDENER
PRODUCT NO.
M2100002AEDXB1
SUPPLIER
EMERGENCY TELEPHONE
MANUFACTURER
2 HAZARDS IDENTIFICATION
Flammable. Vapours may cause drowsiness and dizziness. Irritating to skin. Risk of serious damage to eyes. Harmful to aquatic organisms,
may cause long-term adverse effects in the aquatic environment.
CLASSIFICATION (1999/45)
Xi;R38, R41. R10, R52/53, R67.
ENVIRONMENT
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
PHYSICAL AND CHEMICAL HAZARDS
The product is flammable, and heating may generate vapours which may form explosive vapour/air mixtures.
HUMAN HEALTH
In high concentrations, vapours and spray mists are narcotic and may cause headache, fatigue, dizziness and nausea. Risk of serious
damage to eyes. Vapours/aerosol spray may irritate the respiratory system.
3 COMPOSITION/INFORMATION ON INGREDIENTS
Name
EC No.
CAS-No.
Content %
Classification (67/548)
1-METHOXY-2-PROPANOL
203-539-1
107-98-2
30-60%
R10 R67
XYLENE
215-535-7
1330-20-7
10-30%
ISO-BUTANOL
201-148-0
78-83-1
10-30%
68611-50-7
1-5%
4 FIRST-AID MEASURES
GENERAL INFORMATION
General first aid, rest, warmth and fresh air. Do not give victim anything to drink if they are unconscious. Get medical attention if any
discomfort continues.
1/ 5
PRIMER 7E HARDENER
INHALATION
Place unconscious person on the side in the recovery position and ensure breathing If respiratory problems, artificial respiration/oxygen.
Get medical attention if any discomfort continues.
INGESTION
Immediately rinse mouth and drink plenty of water or milk. Keep person under observation. Do not induce vomiting. If vomiting occurs, keep
head low. Transport immediately to hospital and bring along these instructions.
SKIN CONTACT
Immediately remove contaminated clothing. Wash off promptly and flush contaminated skin with water. Promptly remove clothing if soaked
through and flush skin with water.
EYE CONTACT
Make sure to remove any contact lenses from the eyes before rinsing. Promptly wash eyes with plenty of water while lifting the eye lids.
Get medical attention promptly if symptoms occur after washing.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Fire can be extinguished using: Water spray, fog or mist. Foam, carbon dioxide or dry powder. Dry chemicals, sand, dolomite etc.
SPECIAL FIRE FIGHTING PROCEDURES
Use pressurised air mask if product is involved in a fire. Cool containers exposed to flames with water until well after the fire is out. Keep
run-off water out of sewers and water sources. Dike for water control.
UNUSUAL FIRE & EXPLOSION HAZARDS
Fire causes formation of toxic gases.
PROTECTIVE MEASURES IN FIRE
Self contained breathing apparatus and full protective clothing must be worn in case of fire.
STD
TWA - 8 Hrs
1-METHOXY-2-PROPANOL
WEL
100 ppm
375 mg/m3
150 ppm
560 mg/m3
ISO-BUTANOL
WEL
50 ppm
154 mg/m3
75 ppm
231 mg/m3
XYLENE
WEL
50 ppm
220 mg/m3
100 ppm
441 mg/m3
2/ 5
STEL - 15 Min
Notes
Sk
Sk
PRIMER 7E HARDENER
WEL = Workplace Exposure Limit.
Sk = Can be absorbed through skin.
INGREDIENT COMMENTS
WEL = Workplace Exposure Limits
PROTECTIVE EQUIPMENT
PROCESS CONDITIONS
Provide eyewash station.
ENGINEERING MEASURES
Provide adequate ventilation, including appropriate local extraction, to ensure that the defined occupational exposure limit is not exceeded.
All handling to take place in well-ventilated area.
RESPIRATORY EQUIPMENT
Wear mask supplied with:
Gas cartridge suitable for organic substances.
HAND PROTECTION
Use protective gloves made of: Neoprene. Nitrile. Rubber (natural, latex).
EYE PROTECTION
Wear splash-proof eye goggles to prevent any possibility of eye contact.
OTHER PROTECTION
Wear appropriate clothing to prevent any possibility of skin contact.
HYGIENE MEASURES
DO NOT SMOKE IN WORK AREA! Wash at the end of each work shift and before eating, smoking and using the toilet. Promptly remove
any clothing that becomes contaminated. Use appropriate skin cream to prevent drying of skin. When using do not eat, drink or smoke.
Liquid
COLOUR
Amber
ODOUR
Aromatic.
SOLUBILITY
116-130
0.96 20 deg C
23 deg C
300
AUTO IGNITION
TEMPERATURE (C)
11 TOXICOLOGICAL INFORMATION
GENERAL INFORMATION
Prolonged and repeated contact with solvents over a long period may lead to permanent health problems.
3/ 5
PRIMER 7E HARDENER
INHALATION
In high concentrations, vapours may irritate throat and respiratory system and cause coughing.
INGESTION
Gastrointestinal symptoms, including upset stomach.
SKIN CONTACT
Acts as a defatting agent on skin. May cause cracking of skin, and eczema. Irritating to skin.
EYE CONTACT
Risk of serious damage to eyes.
12 ECOLOGICAL INFORMATION
ECOTOXICITY
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
13 DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
Waste to be treated as controlled waste. Disposal to licensed waste disposal site in accordance with local Waste Disposal Authority.
DISPOSAL METHODS
Dispose of waste and residues in accordance with local authority requirements. Make sure containers are empty before discarding
(explosion risk). Absorb in vermiculite or dry sand and dispose of at a licenced hazardous waste collection point.
14 TRANSPORT INFORMATION
ENVIRONMENTALLY
HAZARDOUS
SUBSTANCE/MARINE
POLLUTANT
UN NO. ROAD
No.
ADR CLASS
III
(D/E)
30
HAZCHEM CODE
3YE
UN NO. SEA
1993
IMDG CLASS
III
EMS
F-E, S-E
UN NO. AIR
1993
AIR CLASS
III
1993
15 REGULATORY INFORMATION
4/ 5
PRIMER 7E HARDENER
LABELLING
Irritant
RISK PHRASES
R10
Flammable.
R38
Irritating to skin.
R41
R52/53
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
R67
NC
Not classified.
SAFETY PHRASES
NATIONAL REGULATIONS
The Chemicals (Hazard Information and Packaging for Supply) Regulations 2002. No. 1689. Workplace Exposure Limits 2005 (EH40)
16 OTHER INFORMATION
GENERAL INFORMATION
The user must be instructed in the proper work procedure and be familiar with the contents of these instructions.
REVISION DATE
25/07/2010
REV. NO./REPL. SDS GENERATED 3
RISK PHRASES IN FULL
R10
Flammable.
R20/21
R37/38
R38
Irritating to skin.
R41
R51/53
Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
R67
DISCLAIMER
The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in
accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using
the product in combination with any other product or any other process is the responsibility of the user.
5/ 5
TEST REPORTS
APPROVALS
B6TH-40-K005-00329_00
329-0
DOCUMENT TRANSMITTAL
Transmittal No.:
23305/CVL/TN/0005
To
CompanyName
Address
Attn.
CC
:
:
:
:
Project No.:
3219
Contract No.:
GC11113800
* Status Legend
5 - AWC
6 - Approved
PROJECT : EPIC FOR INSTALLATION OF CEMS NOZZLES & ASSOCIATED STRUCTURES AT RG PLANT AT
DUKHAN
Enclosed are the following documents as listed below
S.#
DOC. NO.
REV.
PGS.
DESCRIPTION
SET
*STS
DUE DT.
3219-MS-CIV-001
13
15-Jan-12
3219-MS-CIV-002
23
15-Jan-12
3219-MS-CIV-003
27
15-Jan-12
3219-MS-CIV-004
29
15-Jan-12
3219-MS-CIV-005
33
15-Jan-12
3219-MS-CIV-006
49
15-Jan-12
3219-MS-CIV-007
25
15-Jan-12
3219-MS-CIV-008
03
15-Jan-12
3219-MS-CIV-009
02
15-Jan-12
10
3219-MS-CIV-010
02
15-Jan-12
Authorized Signature
Noore Sattar
M. Luwerd Crisho
Project Manager
Date
27-Dec-11
Please acknowledge receipt of the item(s) listed above by signing and returning a copy of this form.
Receivers Signature & Name
Page 1 of 2
Designation
27-Dec-11, 6:06PM
Date
DOCUMENT TRANSMITTAL
Transmittal No.:
23305/CVL/TN/0005
To
CompanyName
Address
Attn.
CC
:
:
:
:
Project No.:
3219
Contract No.:
GC11113800
* Status Legend
5 - AWC
6 - Approved
PROJECT : EPIC FOR INSTALLATION OF CEMS NOZZLES & ASSOCIATED STRUCTURES AT RG PLANT AT
DUKHAN
Enclosed are the following documents as listed below
S.#
DOC. NO.
REV.
PGS.
DESCRIPTION
SET
*STS
DUE DT.
11
3219-MS-CIV-011
03
15-Jan-12
12
3219-MS-CIV-012
04
15-Jan-12
13
3219-MS-CIV-013
02
15-Jan-12
14
3219-MS-CIV-014
02
15-Jan-12
Authorized Signature
Noore Sattar
M. Luwerd Crisho
Project Manager
Date
27-Dec-11
Please acknowledge receipt of the item(s) listed above by signing and returning a copy of this form.
Receivers Signature & Name
Page 2 of 2
Designation
27-Dec-11, 6:06PM
Date
EDD/GC11113800/EXT/TN/0027
Contract Title : EPIC FOR INSTALLATION OF CEMS NOZZLES & ASSOCIATED STRUCTURES AT RG PLANT
Forwarded to
Codes
Company : DOPET
1
2
Item
No. QP Document No.
1
3219-MS-CIV-0001
Rev.
0
Your
Ref.
TN/0025
3219-MS-CIV-0002
TN/0025
3219-MS-CIV-0003
TN/0025
3219-MS-CIV-0004
TN/0025
3219-MS-CIV-0005
TN/0025
3219-MS-CIV-0006
TN/0025
3219-MS-CIV-0007
TN/0025
3219-MS-CIV-0008
TN/0025
3219-MS-CIV-0009
TN/0025
10
3219-MS-CIV-0010
TN/0025
11
3219-MS-CIV-0011
TN/0025
12
3219-MS-CIV-0012
TN/0025
13
3219-MS-CIV-0013
TN/0025
14
3219-MS-CIV-0014
TN/0025
Description
MATERIAL APPROVAL REQUEST FOR
REINFORCEMENT STEEL (VARIOUS DIAMETER)
MATERIAL APPROVAL REQUEST FOR WATER
PROOFING MEMBRANE (FOSROC-PROOFEX GP
1.6MM THICK) & PROTECTION BOARD (6MM)
MATERIAL APPROVAL REQUEST FOR NONSHRINK GROUT (CONBEXTRA GP)
MATERIAL APPROVAL REQUEST FOR
RENDEROC BF2 (BLOWHOLES FILLER FOR
STRUCTURAL CONCRETE)
MATERIAL APPROVAL REQUEST FOR EXPOXY
RESIN COATING (NITOCOTE NT 402)
MATERIAL APPROVAL REQUEST FOR JOINT
SEALANT (THIOFLEX 600)
MATERIAL APPROVAL REQUEST FOR BONDING
AGENT (NITOBOND EP & NETOBOND AR)
MATERIAL APPROVAL REQUEST FOR
AGGREGATES 20MM & 10MM DIAMETER
MATERIAL APPROVAL REQUEST FOR WASHED
SAND
MATERIAL APPROVAL REQUEST FOR WATER
Code
1
Due date
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
Page 1 of 2
27-12-2011 12:54:26