1/11/11
12:00
Page 40
Cavity Fixings
Cavity Fixings
The Hollo-Bolt and Lindibolt eliminate the need
for conventional through-bolting or welding of
structural hollow section (SHS) or any steel
structure where access is only available from
one side.
In the late 1940s, Lindapter revolutionised blind
connections with the development of the original
Lindibolt, for situations where access to both sides
of the steel was restricted. Following the
introduction and wide acceptance of SHS, the
Hollo-Bolt was invented to suit virtually any type
of hollow section, including square, rectangular,
circular and oval profiles. As with all Lindapter
products, the R&D department has continued to
develop the range with the rapid expansion in
diameters, lengths, finishes, and head types.
Following comprehensive testing, The Steel
Construction Institute (SCI) and British
Constructional Steelwork Association (BCSA)
recognise the Hollo-Bolt as a primary structural
connection, in the design guide Joints in Steel
Construction Simple Connections.
The Hollo-Bolt has CE Mark Certification, and is
also approved by the Deutsches Institut fr
Bautechnik and TV NORD.
Both the Lindibolt and Hollo-Bolt enable fast and
safe construction and can be swiftly installed by
simply inserting the product into pre-drilled holes,
then tightening to the recommended torque using
hand tools.
Typical Hollo-Bolt applications include:
Primary Connections
Secondary Connections
Bridges
Cladding
Balconies
Towers and masts
Staircases and handrails
Glazing and roofs
40
1/11/11
12:01
Page 41
Cavity Fixings
Type HB - Hollo-Bolt
Type HB - Hollo-Bolt
Steel, bright zinc plated plus JS 500
Steel, hot dip galvanised
Stainless Steel Grade 316
Collar
Rubber Washer
Sleeve
Cone
Bolt
Suitable for hollow sections, tubes and where access is available from
one side only. For high corrosion protection the Hollo-Bolt comes with
additional JS500 protection as standard or hot dip galvanised.
Sizes M16 and M20 have a patented collapse mechanism for
optimised clamping force.
Awarded the Design Councils Millennium Product status for
innovation in the year 2000.
Installation Hollo-Bolt
Rubber Washer
Across Flats
A/F
Rubber Washer
compressed /
increased
clamping force
3. Using a torque
wrench, tighten the
central bolt to the
recommended torque.
41
1/11/11
12:01
Page 42
Cavity Fixings
Type HB - Hollo-Bolt
Type HB - Hollo-Bolt
Product
Code
HB08-1
Bolt
M8x50
Clamping
Thickness
W
mm
Outer
Ply1)
min t
mm
3 - 22
Sleeve
Length Outer
L
d
Collar
Height
H
D
A/F
d
mm mm
TighteningTorque
Nm
30
HB08-2
M8x70
22 - 41
49
HB08-3
M8x90
41 - 60
68
HB10-1
M10x55
3 - 22
30
HB10-2
M10x70
22 - 41
48
HB10-3
M10x90
41 - 60
67
HB12-1
M12x60
3 - 25
35
HB12-2
M12x80
25 - 47
57
HB12-3
M12x100
47 - 69
79
HB16-1
M16x75
12 - 29
41.5
HB16-2
M16x100
29 - 50
63
HB16-3
M16x120
50 - 71
84
50
HB20-1
M20x90
12 - 34
HB20-2
M20x120
34 - 60
76
HB20-3
M20x150
60 - 86
102
13.75
22
19
23
4.0
5.0
17.75
29
24
45
8.5
10.0
19.75
32
30
80
10.5
15.0
25.75
38
36
190
21.0
30.0
32.75
10
51
46
300
35.0
40.0
Published by
SCI/BCSA Connections Group.
Publication Number: P212
ISBN 1 85942 072 9
Lindapter is a member of SCI
and BCSA
42
Hole
Hole Distances
Edge Distances
d1
min A
min B
mm
mm
mm
mm
HB08
14 (+1.0 / -0.2)
35
13
B + C > 17.5
HB10
18 (+1.0 / -0.2)
40
15
B + C > 22.5
HB12
20 (+1.0 / -0.2)
50
18
B + C > 25.0
HB16
26 (+2.0 / -0.2)
55
20
B + C > 32.5
HB20
33 (+2.0 / -0.2)
70
25
B + C > 33.0
min t
B+C
d1
d1
1/11/11
12:01
Page 43
Cavity Fixings
Sleeve
H
W
Cone
Installation Nut
A/F
Counter
Sunk
Bolt
Clamping
Thickness
Outer
Ply
Sleeve
Overall
Length Outer
(inc. collar)
L
d
mm
mm
35
HBFF08-1
mm
M8x50
W
mm
10 - 27
min t
mm
8
HBFF08-2
M8x70
27 - 45
HBFF08-3
M8x90
45 - 64
HBFF10-1
M10x50
12 - 27
HBFF10-2
M10x70
27 - 45
54
HBFF10-3
M10x90
45 - 64
73
HBFF12-1
M12x55
12 - 30
HBFF12-2
M12x80
30 - 52
64
HBFF12-3
M12x100
52 -74
86
54
Collar
Height
Installation
Tool
A/F
Tightening
Torque
mm
Nm
kN
kN
H
D
mm mm
13.75
24
19
23
4.0
5.0
17.75
30
24
45
8.5
10.0
19.75
33
30
80
10.5
15.0
73
10
36
10
42
Order example: HBFF08-1 BZP plus JS 500 without / with ____ installation nut(s)
1) The Hollo-Bolt can be used on a wide variety of steel hollow shape sections; safe working loads shown are based on use in S275
structural hollow section. The safe working loads, in both tension and shear, are applicable to the Hollo-Bolt only. Failure of the
section, particularly on those with thin walls and a wide chord face, could occur at a lower figure and its strength should be
checked by a qualified structural engineer.
Hole
Countersunk
Depth
Hole Distances
Edge Distances
d1
d2
t1
min A
min B
B+C
mm
mm
mm
mm
mm
mm
HBFF08
14 (+1.0 / -0.2)
27
6.5
35
13
B + C > 17.5
HBFF10
18 (+1.0 / -0.2)
31
6.5
40
15
B + C > 22.5
HBFF12
20 (+1.0 / -0.2)
35
7.5
50
18
B + C > 25.0
90
d2
t1
d1
d1
Installation nut
1. Align pre-drilled fixture and
steelwork. Insert Hollo-Bolt
through fixture and steelwork.
2. Apply installation nut and grip nut
with an open ended spanner.
3. Using a torque wrench, tighten the
central counter-sunk bolt to the
recommended torque.
43
1/11/11
12:01
Page 44
Cavity Fixings
HB08
HB10
HB12
HB16
HB20
HBST08
HBST10
HBST12
HBST16
HBST20
Tensile
Ft,Rk (kN)
Shear
Fv,Rk (kN)
Material Strength
of Sleeve N/mm2
Designation
Nominal Size
Tensile
Ft,Rk (kN)
Shear
Fv,Rk (kN)
Material Strength
of Sleeve N/mm2
23.1
39.6
45.8
84.3
124.0
26.8
46.0
53.3
98.0
154.0
32.9
54.2
71.0
139.0
211.0
30.7
51.0
65.0
128.0
205.0
430
430
430
430
390
500
500
500
500
500
HBFF08
HBFF10
HBFF12
HBSTFF08
HBSTFF10
HBSTFF12
M08
M10
M12
M08
M10
M12
23.1
39.6
45.8
26.8
46.0
53.3
32.9
54.2
71.0
30.7
51.0
65.0
430
430
430
500
500
500
M08
M10
M12
M16
M20
M08
M10
M12
M16
M20
Countersunk Hollo-Bolt
Designation
Nominal Size
Tensile
Ft,Rk (kN)
Shear
Fv,Rk (kN)
Material Strength
of Sleeve N/mm2
HBCSK08
HBCSK10
HBCSK12
HBCSK16
HBSTCSK08
HBSTCSK10
HBSTCSK12
HBSTCSK16
M08
M10
M12
M16
M08
M10
M12
M16
23.1
39.6
45.8
84.3
26.8
46.0
53.3
98.0
32.9
54.2
71.0
139.0
30.7
51.0
65.0
128.0
430
430
430
430
500
500
500
500
Designation
Nominal Size
HBBH/HBFT/HBPR
HBBH/HBFT/HBPR
HBBH/HBFT/HBPR
M08
M10
M12
Tensile
Ft,Rk (kN)
Shear
Fv,Rk (kN)
Material Strength
of Sleeve N/mm2
23.1
39.6
45.8
32.9
54.2
71.0
430
430
430
The characteristic values for the Hollo-Bolt listed in the above tables are for use when designing bolted connections to Eurocode 3 only,
these are not standard safe working loads.
Hollo-Bolt lengths 1, 2 and 3 are covered by this ETA-10/0416.
The characteristic values are used to determine the design resistance of the Hollo-Bolt.
The design resistance is calculated by dividing the characteristic value by a partial factor gM2.
The partial factor is a nationally determined parameter (gM2 =1.25 in the UK).
For standard Hollo-Bolt safe working loads with a factor of safety of 5:1 please refer to the Hollo-Bolt tables on pages 42 an 43.
The characteristic values are valid for the Hollo-Bolt assembly itself, in any connection detail the design resistance of the connection may be limited to
a lesser value. For example, when the thickness of the connected component is small, pull out failure may occur before failure of the Hollo-Bolt.
Design checks should be carried out on the section member to determine the static design resistance.
The SCI Greenbook publication P358 Joints in Steel construction, Simple Joints to Eurocode 3 contains a number of checks on the section.
The characteristic values are only valid when the Hollo-Bolts are installed as per our installation instructions.
Hexagonal Head
Flush Fit
Button Head
Security
Countersunk
(Head)
44
M8
M10
M12
M16
M20
JS500
Stainless
Steel
Sheraplex
Hot Dip
Galv.
1/11/11
12:01
Page 45
Cavity Fixings
Washer
Main Body
Setscrew
Cone
Locknut
Nut
D
F
d
Y
W
Product
Code
1)
LB10
Lindibolt
Size Length
Z
Y
mm
M10
69
Hole
d
min
max
mm
mm
11
11.5
Clamping
Length
W
mm
7 - 30
Projection
LB12
M12
80
13
13.5
5.0
5.0
10 - 36
9 - 12
M12
31
19
LB16
M16
105
17
17.5
8.0
9.8
12 - 48
12 - 16
M16
81
LB20
M20
128
21
21.5
14.0
15.2
14 - 60
15 - 20
M20
LB24
M24
158
25
25.5
20.0
22.5
18 - 72
18 - 24
M24
P
mm
7.5 - 10
M5
Setscrew F
Tightening
Torque
Nm
6
A/F
mm
8
M6
11
10
24
M8
23
13
129
30
M10
45
17
203
36
M12
80
19
Bolt
F
The safe working loads, in both tension and shear, shown above are applicable to the Lindibolt 2 only.
Failure of the section, particularly on those with thin walls and a wide chord face, could occur at a lower figure and its strength should be checked.
Installation
45
1/11/11
12:01
Page 46
Cavity Fixings
Typical Applications
HB001
46
HB002
HB003
HB004
HB005
HB006
1/11/11
12:01
Page 47
Cavity Fixings
Typical Applications
HB007
HB008
HB009
HB010
HB011
HB012
47