Anda di halaman 1dari 9

PROBLEMS ON JET PROPULSION

Unless otherwise stated, the following data may be used:


Cp for air = 1.005 kJ/kg K, R = 0.287 kJ/kg K, = 1.4
Cp for gas = 1.148 kJ/kg K, R = 0.287 kJ/kg K, = 1.33

Aircraft Performance Criteria


1.

An advanced fighter engine operating at Mach 0.8 and 10 km altitude (ambient


temperature of 223.15 K) has the following performance data, and uses a fuel with calorific
value 42800 kJ/kg: Thrust = 50 kN, air mass flow = 45 kg/s, and fuel mass flow = 2.65 kg/s. Find
the specific thrust, TSFC, exit velocity, thermal, propulsive and overall efficiencies (assume
exit pressure equal to ambient pressure).
[1111 m/s, 0.053 kg/s/kN, 239.6 m/s, 1275.6 m/s, 33.04 %, 31.97 %, 10.56 %]

2. Find the propulsive efficiency for the following two engines at cruise
(a) an RB 211 at 30000 ft (ambient pressure and temperature of 28.52 kPa and 226.4 K),
flight Mach number 0.85, approximate jet velocity 390 m/s.
[79.4 %]
(b) an Olympus 593 (in Concorde) at 51000 ft (ambient pressure and temperature of 11
kPa and 216.7 K) flight Mach number 2.0, approximate jet velocity 1009 m/s.
[73.8 %]
3.

If the SFC at cruise for a version of the RB 211 is about 0.60 kg/h/kg and for the Olympus 593
is about 1.19 kg/h/kg, find the overall efficiency and the thermal efficiency in each case.
[35.1 % & 44.2 %; For Olympus 40.7 % & 55.1 %]
Take calorific value of fuel=43 MJ/kg.

4. A turbofan engine on a test stand in the laboratory operates continuously at a thrust level of
60,000 lb with a thrust specific fuel consumption of 0.5 h-1. The fuel reservoir feeding the
engine holds 1000 gallon of jet fuel (1 gallon = 6.7 lb). If the reservoir is full at the beginning of
the test, how long can the engine run before the fuel reservoir is empty?
[0.223 h]
5. The Allison T56 turboprop engine is rated at 4910 equivalent shaft horsepower at zero
velocity at sea level. Consider an airplane with this engine flying at 500 ft/s at sea level. The
jet thrust is 250 lb, and the propeller efficiency is 0.9. Calculate the equivalent shaft
horsepower at this flight condition.
[5163 hp]

Thermodynamic Relations
6.

An axial flow air compressor is designed to provide an overall total-to-total pressure ratio of
8:1. At inlet and outlet the stagnation temperatures are 300 K and 586.4 K respectively.
Estimate the overall total-to-total efficiency and the polytropic efficiency for the
compressor. Assume that for air is 1.4.
[0.85, 0.886]

7. A compressor has an isentropic efficiency of 85% at a pressure ratio of 4.0. Calculate the
corresponding polytropic efficiency, and thence plot the variation of isentropic efficiency
over a range of pressure ratio from 2.0 to 10.0.
[0.876; 0.863 at 2 bar and 0.828 at 10 bar]
8. A low-pressure air compressor develops a pressure of 0.147 bar. If the initial and the final
states of air are p1=1.02 bar, T1=300 K, and T2 =315 K, estimate the isentropic and infinitesimal
stage efficiencies. A second compressor changes the state of air from initial states of
p1=1.02 bar, T1=300 K to p2=2.5 bar with an efficiency of 75 %. Find the infinitesimal efficiency
of this compressor. Explain the large deviation in the efficiency of this compressor from that
[78 %, 78.8 %; 78 %]
of the low-pressure compressor.
9. An aircraft is flying at a cruise speed of 250 m/s at an altitude of 5000 m where the ambient
pressure is 54.05 kPa and ambient temperature is 255.7 K. The ambient air is first decelerated

in a diffuser before it enters the compressor. Assuming both the diffuser and the compressor
to be isentropic, find (a) total pressure at the compressor inlet and (b) the compressor work
per unit mass if the total pressure ratio of the compressor is 8.
[80.77 kPa, 233.9 kJ/kg]

10. Gas enters the nozzles of a turbine stage at a stagnation pressure and temperature of 4.0
bar and 1200 K and leaves with a velocity of 572 m/s and at a static pressure of 2.36 bar.
Find the nozzle efficiency assuming the gas has the average properties over the
[0.957]
temperature range of the expansion of Cp = 1.16 kJ/kg K and = 1.33.

Turbojet Engines
11. Determine the specific thrust and SFC for a simple turbojet engine having the following
component performance at the design point at which the cruising speed and altitude are
M=0.8 and 10000 m (with ambient temperature & pressure of 223.3 K and 0.2650 bar).
Compressor pressure ratio
Turbine inlet (stagnation) temperature
Isentropic Efficiencies
Intake, D
Compressor, c
Turbine, T
Propelling Nozzle, N
Mechanical transmission efficiency, m
Combustion efficiency, B
Combustion pressure loss, pb

8.0
1200 K
93 %
87 %
90 %
95 %
99 %
98 %
4 % Comp. Del. Pr.
[589.7 Ns/kg, 0.121 kg/h-N]

12. A turbojet aircraft is flying at 800 km/h at 10 700 m where the pressure and temperature of
the atmosphere are 0.24 bar and 500 C respectively. The compressor pressure ratio is 10:1
and the maximum cycle temperature is 8200 C. Assuming a convergent nozzle, find the
thrust developed and the specific fuel consumption, using the following data:
Isentropic Efficiencies
Intake, D
Compressor, c
Turbine, T
Propelling Nozzle, N
Mechanical transmission efficiency, m
Combustion efficiency, B
Combustion pressure loss, pb
Calorific value of fuel
Nozzle outlet area

90 %
90 %
92 %
92 %
98 %
98 %
0.14 bar
43 300 kJ/kg
0.08 m2
[6453 N, 0.0291 kg/KN s]

Turbojet with Afterburner


13. A turbojet aircraft is traveling at 925 km/h in atmospheric conditions of 0.45 bar and 260C.
The compressor pressure ratio is 8, the air mass flow rate is 45 kg/s, and the maximum
allowable cycle temperature is 8000C. The compressor, turbine and jet pipe stagnation
isentropic efficiencies are 0.85, 0.89, and 0.9 respectively, the mechanical efficiency of the
drive is 0.98, and the combustion efficiency is 0.99. Assuming a convergent propelling
nozzle, a loss of stagnation pressure in the combustion chamber of 0.2 bar, and a fuel with
calorific value of 43300 kJ/kg, calculate: (i) the required nozzle exit area, (ii) the net thrust
developed, (iii) the air-fuel ratio and (iv) the specific fuel consumption.
[0216 m2, 19.94 kN, 70.87, 0.0319 kg/kN s]

When an afterburner is used to obtain an increase in thrust, calculate the nozzle exit area
now required to pass the same mass flow rate and the new net thrust assuming that

stagnation temperature after the afterburner is 7000C and the pressure loss in the
[0.244 m2, 22 kN]
afterburner process is 0.07 bar.
14. A simple turbojet engine is operating with a compressor pressure ratio of 8.0, turbine inlet

temperature of 1200 K and a mass flow of 15 kg/s, when the aircraft is flying at 260 m/s at an
altitude of 7000 m (with ambient temperature and pressure of 242.65 K and 41.06 kPa).
Assuming the following component efficiencies, calculate the propelling nozzle area
[0.0713 m2, 7896 N, 0.126 kg/N-h]
required, the net thrust developed and SFC.

Polytropic efficiencies of compressor and turbine


Isentropic efficiency of intake
Isentropic efficiency of Propelling nozzle
Mechanical efficiency
Combustion chamber pressure loss
Combustion efficiency

0.87
0.95
0.95
0.99
6 % comp.del.pr.
0.97

The gases in the jet pipe of the above engine are reheated to 2000 K, and the combustion
pressure loss incurred is 3 % of the pressure at the outlet of the turbine. Find the % increase in
nozzle area required if the net flow is to be unchanged, and also the % increase in net thrust.
[48.3 %, 64.5 %]

Turbofan Engines
15. The following data apply to a twin-spool turbofan engine (non-mixed type) with the fan
driven by the LP turbine and the compressor by the HP turbine. Separate cold and hot
nozzles are used. Determine the thrust and SFC under sea-level static conditions where the
[71.5 kN, 0.0403 kg/h N]
ambient pressure and temperature are 1.0 bar and 288 K.
Overall pressure ratio
Fan pressure ratio
By-pass ratio
Turbine inlet temperature
Fan, compressor and turbine polytropic efficiency
Isentropic efficiency of each propelling nozzle
Mechanical efficiency of each spool
Combustion pressure loss
Total air mass flow

25.0
1.65
5.0
1550 K
0.90
0.95
0.99
1.50 bar
215 kg/s

16. Under take-off conditions when the ambient pressure and temperature are 1.01 bar and 288
K, the stagnation pressure and temperature in the jet pipe of a turbojet engine are 2.4 bar
and 1000 K, and the mass flow is 23 kg/s. Assuming that the expansion in the converging
propelling nozzle is isentropic, calculate the exit area required and the thrust produced.
For a new version of the engine, the thrust is to be increased by the addition of an aft fan,
which provides a separate cold exhaust stream. The fan has a by-pass ratio of 2.0 and
pressure ratio of 1.75, isentropic efficiencies of the fan and the fan-turbine sections being
0.88 and 0.90 respectively. Calculate the take-off thrust assuming that the expansion in the
cold nozzle is also isentropic, and that the hot nozzle area is adjusted so that the hot mass
[0.0763m2, 15.35 kN, 24.9 kN]
flow remains at 23 kg/s.

Turbofan Engines with Duct Heater

17. Extending the problem 16 on turbofan engine with additional information that the
combustion efficiency is 0.99, determine the SFC. Also, calculate the thrust and SFC when a
combustion chamber is incorporated in the bypass duct and the cold stream is heated to
1000 K. The combustion efficiency and pressure loss for this process may be assumed to be
[0.0429 kg/ h N; 55.95 kN; 0.128 kg/h N]
0.97 and 0.05 bar respectively.

Turboprop Engines
18. A turboprop engine is operating under following conditions:
Flight speed at sea-level, standard day
Airflow entering the compressor
Compressor pressure ratio (total-to-total)
Efficiencies
Diffuser
Compressor
Turbine to drive compressor
Turbine to drive the propeller
Nozzle
Turbine inlet temperature (stagnation)
Stagnation pressure leaving power turbine

0
1.0 kg/s
12
100 %
87 %
89 %
89 %
100 %
1400 K
1.724 bar

Calculate (a) the power delivered by the engine to the propeller


(b) the thrust developed by the engine
(c) the equivalent shaft power
(d) the equivalent specific fuel consumption
19. Thought is being given to developing a new turboprop engine with an eight bladed
propeller specially designed for flight at M=0.7 at an altitude of 12 Km. An existing turbojet
engine has a gas generator design that (with the addition of a free turbine, gear reducer,
propeller and new propulsion nozzle) would be used for the engine. At the above altitude
and flight Mach number the gas generator exit conditions are
Mass flow
Total pressure
Total temperature

100 kg/s
0.04 Mpa
1200 K

If these same conditions were to apply at entrance to the free-power turbine of the
turboprop, determine the best combination of the propeller thrust and nozzle thrust for the
turboprop engine given the following expected adiabatic efficiencies:
Propeller, pr
Nozzle, n
Power turbine, pt

0.79
0.98
0.89

The mechanical efficiency of the gearbox is g = 0.97. Assume the turbine working fluid has
= 1.33 and molecular weight of 30.
[59 kN (propeller)]

Ramjet Engines
20. Compare the specific fuel consumption of a turbojet and a ramjet that are being

considered for flight at M = 1.5 and 50,000 ft altitude (with ambient pressure and
temperature of 11.6 kPa and 205 K respectively). The turbojet pressure ratio is 12 and the
maximum allowable temperature is 1400 K. For the ramjet the maximum temperature is 2500
K. For simplicity, ignore aerodynamic losses in both engines. Conventional hydrocarbon fuels
are used with heating value of 45,000 kJ/kg. Assume = 1.4 and Cp = 1.0 kJ/kg K.
[0.0558 kg/kN.s (ramjet), 0.0252 kg/kN.s (turbojet)]

21. A ramjet engine is to propel an aircraft at Mach 3 at high altitude where the ambient
pressure is 8.5 kPa and the ambient temperature is 220 K. The turbine inlet temperature is
2540 K. If all the components of the engine are ideal-that is, frictionless-determine (a) the
thermal efficiency, (b) the propulsive efficiency and (c) the overall efficiency. Let the
specific heat ratio be 1.4 and make the approximations appropriate to f << 1.

Mechanics of Flight

22. The L/D ratio of a seaplane is 30. The seaplane has a wing area of 10 m2 and weighs 3150
N. What is the CD when it is in steady flight at 170 km/hr at an altitude of 900 m. Take
900 =1.1226 kg/m3.
23. An aircraft has a lift to drag ratio of 15. It is at an altitude of 1500 m when the engine fails.
An airport is 10 km ahead of the engine failure point. Will the pilot be able to reach the
airport?
24. An airplane weighs 160, 000 N and has a wing area of 42 m2. At a flight speed of 100 m/s
the engine gives a thrust of 27000 N. If the aircraft drag equation is CD=0.014 + 0.05 CL2
find the angle and rate of climb at sea level at 100 m/s flight speed.
25. An aircraft makes a level turn in a circle of radius 180 m when cruising at a speed of 100
knots (1 knot=0.514 m/s). Find the correct angle of banking. If the aircraft makes an 1800
turn in one minute at the same speed and its mass is 12 ton, find the angle of banking
required and the lift force.
26. Calculate the range of a propeller driven aircraft with loaded gross weight=75000 N, fuel
capacity=4000 litres, sfc=3 N/kW-hr, average L/D=15, and propeller efficiency=85 %.
Assume density of fuel to be 0.8 kg/litre, and complete fuel is consumed during the flight.
27. An airplane requires 380 hp for level flight at 150 mph, when flying weight is 4000 lb.
What will be corresponding speeds and power required if the flying weight is increased to
4500 lb.
28. Find the range obtained with an aircraft if the cruise L/D = 20, sfc = 1.613 x 10-5 kg/s/N,
the initial mass at the start of cruise is 612.9 x 103 kg and the mass at the end of cruise is
399.5 x 103 kg. As a simplification, assume that the aircraft moves at a speed of 256.5 m/s
throughout the flight.
29. For a four digit NACA airfoil CLmax=1.67 +7.8 pz-2.6(0.145-0.5z-t)2/t3/2, where z is the
maximum camber as fraction of chord , p is the position of maximum camber as fraction
of chord from leading edge, and t is the thickness as fraction of chord. Determine the
CLmax for NACA 2415.
Rocket Performance Parameters

30. A rocket projectile has the following characteristics:


Initial mass
Mass after rocket operation
Payload, nonpropulsive structure etc.
Rocket operation duration
Average specific impulse of propellant
5

200 kg
130 kg
110 kg
3.0 sec
240 sec

Find the (a) vehicles mass ratio, (b) mass ratio of the rocket system (c) propellant mass
fraction, (d) propellant flow rate, (e) thrust, (f) initial and final thrust-to-weight ratio, (g)
acceleration of the vehicle, (h) effective exhaust velocity, (i) total impulse, and (j) the
impulse-to-weight ratio.
[0.65, 0.22, 0.778, 54.8 kN, 28, 43, 421 m/s2, 2352 m/s, 164.6 kN-sec, 187]
31. The following measurements were made in a sea level test of a solid rocket motor:
Burn duration
Initial mass before test
Mass of rocket motor after test
Average thrust
Chamber pressure
Nozzle exit pressure
Nozzle throat diameter
Nozzle exit diameter

40 sec
1210 kg
215 kg
62,250 N
7.00 Mpa
0.070 Mpa
0.0855 m
0.2703 m

Determine mass flow rate, actual average exhaust velocity, characteristic velocity, effective
exhaust velocity and specific impulse at sea level, and effective exhaust velocity and specific
impulse at 1000 and 25,000 m altitude. Assume an invariant thrust and mass flow rate and
negligible short start and stop transients. (For altitudes of 1 km & 25 km the ambient
pressure is 0.0898 and 0.00255 Mpa respectively).

[24.9 kg/s, 2572 m/s, 1613 m/s, 2500 m/s, 255 sec; 2527 m/s, 258 sec; 2727 m/s, 278 sec]

32. The following data are given for a certain rocket unit:
Thrust
Propellant consumption
Velocity of vehicle
Energy content of propellant

8896 kN
3.867 kg/s
400 m/s
6.911 MJ/kg

Determine (a) the effective exhaust velocity, (b) the kinetic jet energy rate per unit flow of
propellant, (c) the internal efficiency, (d) the propulsive efficiency, (e) the overall efficiency,
(f) the specific impulse and (g) the specific propellant consumption. Assume combustion
efficiency to be 98 %.
[2300 m/s, 2.645 MJ-sec/kg, 38.3 %, 33.7 %, 13.3 %234.7 sec, 0.00426 sec-1]
Rocket Nozzle Theory

33. An ideal rocket chamber is to operate at sea level using propellants whose combustion
products have a specific heat ratio of 1.3. Find the required chamber pressure and the
nozzle area ratio between throat and exit if the nozzle exit Mach number is 2.4. The nozzle
inlet Mach number may be considered to be very small.
[1.5 Mpa, 2.64]
34. A rocket operates at sea level (p=0.1013 Mpa) with a chamber pressure of 2.068 Mpa and a
chamber temperature of 2222 K and a propellant consumption of 1 kg/s. Assuming a ratio
of specific heats to be 1.3 and gas constant to be 345.7 kJ/kg K, show graphically the
variation of area, temperature, specific volume and velocity with respect to pressure along
the nozzle. Calculate the ideal thrust and ideal specific impulse.
35. The German World War-II A-4 propulsion system had a sea level thrust of 25,400 Kg and a
chamber pressure of 1.5 Mpa. If the exit pressure is 0.084 Mpa and the exit diameter is 740
mm, what is the thrust at 25,000 m, where the ambient pressure is 2.6077 x 103 N/m2.
6

36. Derive the equation for the theoretical correction factor for a conical nozzle assuming that
all the mass flow originates at the apex of the cone. Hence, calculate the nozzle angle
correction factor for a nozzle whose divergent half angle is 130.
37. Design a rocket nozzle to conform to the following conditions:
Chamber pressure
Atmospheric pressure
Chamber temperature
Mean molecular mass of gases
Ideal specific impulse
Specific heat ratio
Desired thrust

20.4 atm = 2.068 Mpa


1.0 atm
2861 K
21.87 kg/kg-mol
230 sec
1.229
1300 N

Find nozzle throat and exit areas, respective diameters, actual exhaust velocity, and actual
specific impulse.
[4.66 cm2; 2.43 cm; 15.9 cm2; 4.5 cm; 2074 m/s; 212 sec]
38. The following data are given for an ideal rocket:
Average molecular mass
Chamber pressure
External pressure
Chamber temperature
Throat area

24 kg/kg-mol
2.53 Mpa
0.090 Mpa
2900 K
0.00050 m2

Assuming specific heat ratio of 1.3, determine (a) throat velocity, (b) specific volume at
throat, (c) propellant flow and specific impulse, (d) thrust, (e) Mach number at throat.
39. For an ideal rocket with a characteristic exhaust velocity of 1200 m/s, a mass flow rate of
73.0 kg/s, a thrust coefficient of 1.50 and a nozzle throat area of 0.0248 m2, compute the
effective exhaust velocity, the thrust, the chamber pressure and the specific impulse.
[1800 m/s; 131400 N; 3.530 x 106 N/m2; 183.4 sec]
40. Using a propellant of molecular mass 15 kg/kg-mol and flame temperature 3300 K,
determine the rocket nozzle throat and exit areas required for a thrust of 500 kN and an
ideal impulse of 300 sec. The ambient pressure is 0.1 Mpa, and specific heat ratio of the
propellant is 1.40. (a) How much thrust would this rocket develop if the ambient pressure
were changed to 0.03 Mpa? (b) How much thrust would be developed by a rocket designed
to expand to 0.03 Mpa if it had the same stagnation conditions, throat area and propellant?
[0.0647 m2, 0.342 m2, 523 kN, 533 N]
Solid Rocket Motors

41. The following requirements are given for a solid propellant rocket motor:
Sea level thrust
Duration
Chamber pressure
Operating temperature
Propellant

8900 N (2000 lbf)


10 sec
6.8947 Mpa (1000 psia)
Ambient (approx. 70 F)
Ammonium nitrate-hydrocarbon

Determine the specific impulse, the throat and exit areas, the flow rate, the total propellant
weight, the total impulse, the burning area, and an estimated mass assuming moderately
7

efficient design. Properties of this propellant are: = 1.26; T1 = 1755 K; r = 0.254 cm/sec
at 6.8947 Mpa; c* = 1219.2 m/sec; b= 1550 kg/m3; molecular mass = 22 kg/kg-mol.
Assume a total impulse to weight ratio (It/wG) of 143.
[191 sec, 8.38 cm2, 65.16 cm2,46.6 N/s, 466 N, 485 N, 89000 N-s, 1.187 m2,622.37 N]

42. A solid rocket motor has the following operating characteristics:


Sea level thrust
Duration
Chamber pressure
Specific heat ratio
Chamber temperature
Burning rate
Propellant density
Molecular mass

10,000 N
10 sec
70.928 bar
1.26
2500 K
6 mm/sec at 70.928 bar
1.67 gm/cc
22 kg/kg-mol

Assuming a neutral burning (with a cigarette burning grain) and an adapted nozzle at sea
level, find the (a) characteristic velocity, (b) thrust coefficient at optimum expansion, (c)
specific impulse at sea level, (d) nozzle throat area, (e) weight of propellant and (f) burning
surface area.
[1473 m/s, 1.59, 238 sec, 8.867 cm , 418.4 N, 0.4261 m ]
2

43. Determine the grain geometry and propellant weight of an internal burning tubular grain
solid propellant unit given the following data:
Specific impulse
Burning rate
Specific gravity
Ratio of specific heats
Combustor pressure
Desired average thrust
Maximum outer diameter
Ambient pressure
Vehicle pay load
Desired duration

240 sec at sea level at 70 ata


6 cm/sec at 70 ata
1.65
1.25
70 ata
6000 kgf
400 mm
0.25 ata
2250 kg
6 secs

Determine the nozzle dimensions assuming optimum expansion in the nozzle.


44. The grain in a solid propellant rocket is a hollow cylinder bonded to the casing so that it
burns only on its inner cylindrical surface. Its density is 1650 kg/m3, and its burning rate is
characterized by r=13.3 p10.63 mm/s where p1 is in Mpa. At a point in the burning period
when p1 = 0.7 Mpa, the grain d/D = 0.4 and L/D = 6, L being the grain length and, d and
D being its inner and outer diameters. Determine the rate of change of chamber pressure,
assuming the gas temperature stays constant at 2750 K and that the gas specific heat ratio is
1.24 and D = 1 m.
[0.0862 Mpa/s]
45. The burning rate of a particular propellant is given by r = c/(T1 - T) p1n in which r is in
mm/s, p1 is in Mpa, and T is in K, and
c = 176
T1 = 415 K
n = 0.716
8

When the propellant initial temperature is 293 K, the chamber pressure is 3 Mpa (steady)
for 4 min. If the same propellant grain in the same rocket motor is heated to 318 K, what
would be the new steady state pressure level and burning period. Assume the time required
to reach steady state is small compared to the burning rate.
[1.79 min]
Liquid Rocket Engines

46. A liquid oxygen-liquid hydrogen rocket thrust chamber of 10, 000 lbf thrust operates at a
chamber pressure of 1000 psia, a mixture ratio of 3.40, has exhaust products with a mean
molecular mass of 8.9 lbm/lb-mol, a combustion temperature of 43800 F, and a specific
heat ratio of 1.26. Find the nozzle area, exit area for optimum operation at an altitude where
p3= p2=1.58 psia, the propellant weight and volume flow rates, and the total propellant
requirements for 2 minutes of operation. Assume that the actual specific impulse is 97 % of
the theoretical value.
47. What will be the volume of air tank required to pressurize the propellant tanks of a 9000 N
thrust rocket thrust chamber using 90 % hydrogen peroxide as a monopropellant at a
chamber pressure of 2.00 Mpa for 30 sec in conjunction with a solid catalyst? The air tank
pressure is 14 Mpa and the propellant tank pressure is 3.0 Mpa. Allow for 1.20 % residual
propellant.
48. Determine the shaft speed and the overall impeller dimensions for a liquid oxygen pump
which delivers 500 lb/sec of propellant at a discharge pressure of 1000 psia and a suction
pressure of 14.7 psia. The oxygen tank is pressurized to 35 psia. Neglect the friction in the
suction pipe and the section head changes due to acceleration and propellant consumption.
The initial tank level is 15 ft above the pump suction inlet.

Anda mungkin juga menyukai