Rezumat. Lucrarea pune in evidenta una dintre noile metode inovative de incalzire a
incintelor, in contextul reducerii consumului de energie si a evidentieri unor
echipamente care pot inlocui cu succes echipamentele clasice de incalzire,in spatii mai
pretentioase si mai putin accesibile.Articolul se focuseaza pe studiu functionarii unor
componente importante a acestui echipament si anume schimbatorul de cadura, si
ventilatorul, care implica etalarea anumitor performante: incalzirea in timpi redusi,cu
mentinearea caldurii,pentru o perioada de timp, nivel de zogmot redus, desi materialul
din care sunt facute aceste componente sunt rezistente in timp,si prezinta o calitate
ridicata.Echipamentul este ideal in crearea unui confort termic optim atat in spatiile
vitrate, malluri, resturante, scolii , spitale sau saune.Mai putem mentiona ca convectroul
de pardoseala pote fi utilizat concomintent si cu alte echipamente de incalzire
convetionale , fara a crea perturbatii, in cazul unei functionarii comune.
Abstract. The paper highlights one of the new innovative methods of heating the
premises, in the context of reducing energy consumption and highlighting some
equipment that can successfully replace conventional heating equipment in areas most
demanding and less accessible. The article focuses on the trial operation of major
components of this equipment, namely heat exchanger and fan, which involves the display
of certain performance: heating in reduced time, maintaining the heat for a while, low
noise, although material which are done while these components are resistant, and
features a high quality. The device is ideal in creating an optimal thermal comfort in both
windowed spaces, malls, restaurants, schools, hospitals, or saunas. We can mention that
the floor convector can be used concomitantly with other conventional heating equipment
without creating disturbances, in the case of a joint operation
Keywords: floor convector, heating equipment, thermal comfort, energy efficiency, low noise
level
Articles Title
Articles Title
For inserting equations you may use a 1x2 table (preferred width 14 cm) first
cell=align center (preferred width 12.6), second cell=align right, preferred width
1.4):
E
B
t
(0)
For writing equations, use Math Type or Equation Editor; dont forget impose the
format for each category (the same as for the main text: font Times New Roman,
size 12).
2.1. Subsection header (for new subsection header, select this row and use
Format Painter for the new text, in the appropriate position)
The sub section paragraphs have the same formatting: Font Times New Roman,
regular, size 12; line spacing options: 0 points before and 6 points after the
paragraph.
For inserting figures follow the instructions below the figures.
For citing figures, use: see Figure 1, b.
Fig. 1 For a new figure, copy Fig. 1. at the left of this row and paste in the desired position.
a. Description;
b. Description.
For a new equation dont forget: after copying, press CTRL+A (=select all) then
F9 key for the field be actualized.
1
1
H z
1
H z
e z
ez
H r
y r x, y y
x r x, y x
r r
(0)
Table Title (font Times New Roman, regular, size 10; line spacing options: 12 points before and 6
points after the paragraph)
No
.
Category
1.
2.
10.
11.
Category
d f(t )
dt
Category
Description
m 2.50 kg
l 3.5 m
TR
N
p
1.5 10 5 2
V
m
1234.67
Formula
Numerical value
You may group two or three figures: lock anchor, move with text, horizontal
alignment=top of line, vertical alignment=centered, top & bottom wrapping.
a. Text for a
second row for a.
Fig. 2 Description:
b. Text for b
second row for b.
c. Text for c
second row for c.
For inserting a new table (text wrapping=around, distance from text=0.25, move
with text) follow instructions below.
Table For new table, select & copy Table 2. in the left of this row and paste at the new position.
No.
Category
Category
Category
Articles Title
1.
2.
3.
Text
vx
dx
a e ax a exp(at )
dt
Symbols
Conclusions
Conclusion (1).
Conclusion (z).
Acknowledgment
Only if necessary.
Notations and/or Abbreviations
Only if necessary.
REFERENCES
For the title, use Times New Roman, bold, size 14, character spacing = 4, line spacing options: 24
points before paragraph, and 12 points after. For references, use 10 points fonts, line spacing=1.5.
Use copy, paste, select & replace text. (You must delete this paragraph.)
[1]
Books First Author, Books Second Author, Books title (Publisher, Town, Country, Year).
[2]
Books First Author, Books Second Author, Books title (Publisher, Town, Country, Year) Vol. I, p.
xxx or pp. xxx-xxx.
[3]
Articles First Author, Articles Second Author, Reviews name (=international abbreviation), 24
(=volume number, bold), xx (=page number where the article begins) (Year).
[4]
[5]
[6]
[7]
P. Ring and P. Schuck, The Nuclear Many-Body Problem (Springer-Verlag, Berlin, 1980).
[8]
[9]
6
[10]
V. G. Soloviev, Theory of Atomic Nuclei (Institute of Physics Publishing, Bristol, 1992) pp. 123125.
[11]