Service
Manual
Inverter Pair
Floor Standing Type B-Series
[Applied Models]
Inverter Pair: Cooling Only
Inverter Pair: Heat Pump
SiBE06-514
Inverter Pair
B-Series
zCooling Only
Indoor Unit
FVKS25BVMB
FVKS35BVMB
Outdoor Unit
RKS25DVMB
RKS35DVMB
RKS25D2VMB
RKS35D2VMB
zHeat Pump
Indoor Unit
FVXS25BVMB
FVXS35BVMB
Outdoor Unit
RXS25DVMB
RXS35DVMB
Table of Contents
RXS25D2VMB
RXS35D2VMB
SiBE06-514
1. Introduction .............................................................................................v
1.1 Safety Cautions ........................................................................................v
Part 4
Frequency Principle................................................................................14
Flap Control............................................................................................16
Air Flow Selection...................................................................................17
Fan Speed Control for Indoor Units........................................................18
Programme Dry Function .......................................................................19
Automatic Operation...............................................................................20
Thermostat Control.................................................................................21
NIGHT SET Mode ..................................................................................22
HOME LEAVE Operation .......................................................................23
Inverter POWERFUL Operation .............................................................24
Other Functions......................................................................................25
ii
Table of Contents
SiBE06-514
Safety precautions..................................................................................47
Names of parts .......................................................................................49
Preparation before Operation.................................................................52
AUTO DRY COOL HEAT FAN Operation ......................................55
Adjusting the Air Flow Direction .............................................................57
POWERFUL Operation ..........................................................................59
OUTDOOR UNIT SILENT Operation ....................................................60
HOME LEAVE Operation .......................................................................61
TIMER Operation ...................................................................................63
Care and Cleaning .................................................................................65
Troubleshooting......................................................................................68
5. Check ..................................................................................................113
5.1 How to Check .......................................................................................113
Table of Contents
iii
SiBE06-514
2. Outdoor Unit........................................................................................135
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2. Wiring Diagrams..................................................................................163
2.1 Indoor Units ..........................................................................................163
2.2 Outdoor Units .......................................................................................163
Index
............................................................................................. i
iv
Table of Contents
SiBE06-514
Introduction
1. Introduction
1.1
Safety Cautions
Cautions and
Warnings
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into
Warning and
Caution. The
Warning
items are especially important since they can lead to death or serious injury if they are not
followed closely. The
Caution items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer.
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can
cause an electrical shock or fire.
Introduction
SiBE06-514
Warning
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands can cause an electrical shock.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and cause injury.
Be sure to check that the refrigerating cycle section has cooled down
sufficiently before conducting repair work.
Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place.
Using the welder in an enclosed room can cause oxygen deficiency.
SiBE06-514
Introduction
Warning
Be sure to use the specified cable to connect between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure
that the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire.
Placing heavy items on the power cable, and heating or pulling the power cable
can damage the cable.
Do not mix air or gas other than the specified refrigerant (R410A / R22) in the
refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before
charging the refrigerant. After charging refrigerant, make sure that there is no
refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to
perform pump-down and close the service valve, to prevent the refrigerant gas
from leaking into the room. The refrigerant gas itself is harmless, but it can
generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed
of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly.
For integral units
If the packing and seal are not installed properly, water can enter the room and only
wet the furniture and floor.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires can cause an electrical shock, excessive heat
generation or fire.
vii
Introduction
SiBE06-514
Warning
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it can cause an electrical shock,
excessive heat generation or fire.
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections can cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame can cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding can cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 Mohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture
and floor.
Type of
Information
Note
Description
A note provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
Note:
Caution
Warning
Reference
Caution
Warning
viii
SiBE06-514
Part 1
List of Functions
1. List of Functions ......................................................................................2
List of Functions
List of Functions
SiBE06-514
10
~46
10
~46
15
~20
PAM Control
Swing Compressor
Rotary Compressor
Reluctance DC Motor
Power-Airflow Flap
Power-Airflow Diffuser
Washable Grille
Wide-Angle Louvers
Compressor
Comfortable
Airflow
Operation
Lifestyle
Convenience
Health &
Clean
Longlife Filter
3-D Airflow
{
H2
{
H2
Intelligent Eye
Hot-Start Function
Automatic Defrosting
Automatic Operation
Fan Only
Timer
Worry Free
Reliability &
Durability
Flexibility
10m
10m
Power Selection
Chargeless
Remote
Control
Priority-Room Setting
ECONO Mode
Wireless
Wired
Temperature Display
Functions
Comfort
Control
Category
FVXS2535BVMB
RXS2535D(2)VMB
Functions
FVKS2535BVMB
RKS2535D(2)VMB
FVXS2535BVMB
RXS2535D(2)VMB
Category
FVKS2535BVMB
RKS2535D(2)VMB
1. List of Functions
Remote
Controller
H2 : Digital Only
List of Functions
SiBE06-514
Part 2
Specifications
1. Specifications ..........................................................................................4
1.1 Cooling Only.............................................................................................4
1.2 Heat Pump ...............................................................................................5
Specifications
Specifications
SiBE06-514
1. Specifications
1.1
Cooling Only
230V, 50Hz
Model
Indoor Units
Outdoor Units
Capacity
Moisture Removal
Running Current
Power Consumption
Power Factor
COP
Liquid
Piping
Gas
Connections
Drain
Heat Insulation
Indoor Unit
Front Panel Color
Air Flow Rate m/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current
Power Consumption
Power Factor
Temperature Control
Dimensions (HWD)
Packaged Dimensions (HWD)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Outdoor Unit
Casing Color
Type
Compressor
Model
Motor Output
Model
Refrigerant
Oil
Charge
Model
Refrigerant
Charge
Fan
Note:
mm
mm
kg
kg
FVKS25BVMB
RKS25D(2)VMB
2.5 (1.3~3.0)
8,500 (4,400~10,200)
2,150 (1,110~2,580)
1.2
3.8
695 (300~920)
79.5
3.60
6.4
9.5
18.0
Both Liquid and Gas Pipes
FVKS25BVMB
Almond White
8.1 (286)
6.2 (219)
4.3 (152)
3.4 (120)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable / Washable / Mildew Proof
0.14
32
99.4
Microcomputer Control
600650195
714770294
13
19
FVKS35BVMB
RKS35D(2)VMB
3.5 (1.4~3.8)
11,900 (4,750~12,950)
3,010 (1,200~3,260)
1.9
5.0
1,090 (300~1,250)
94.8
3.21
6.4
9.5
18.0
Both Liquid and Gas Pipes
FVKS35BVMB
Almond White
8.3 (293)
6.3 (222)
4.3 (152)
3.4 (120)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable / Washable / Mildew Proof
0.14
32
99.4
Microcomputer Control
600650195
714770294
13
19
dBA
38 / 32 / 26 / 23
39 / 33 / 27 / 24
dBA
W
A
W
%
A
mm
mm
kg
kg
54
RKS25D(2)VMB
Ivory White
Hermetically Sealed Swing Type
1YC23NXD#A
600
FVC50K
0.375
R410A
0.80
36.2 (1,278)
25.7 (907)
Propeller
31
3.66
663
78.8
3.8
550765285
589882363
30
35
55
RKS35D(2)VMB
Ivory White
Hermetically Sealed Swing Type
1YC23NXD#A
1,500
FVC50K
0.375
R410A
1.00
33.5 (1,183)
23.4 (826)
Propeller
35
4.86
1,058
94.7
5.0
550765285
589882363
32
38
dBA
46 / 43
47 / 44
dBA
61
3D049145
62
3D049146
kW
Btu/h
kcal/h
L/h
A
W
%
W/W
mm
mm
mm
H
M
L
SL
W
Steps
A
W
%
W
L
kg
H
L
Conversion Formulae
kcal/h=kW860
Btu/h=kW3414
cfm=m/min35.3
Specifications
SiBE06-514
1.2
Specifications
Heat Pump
230V, 50Hz
Indoor Units
Model
FVXS25BVMB
RXS25D(2)VMB
Outdoor Units
Capacity
Moisture Removal
Running Current
Power Consumption
Power Factor
COP
Liquid
Piping
Connections Gas
Drain
Heat Insulation
Indoor Unit
Front Panel Color
Air Flow Rate m/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current
Power Consumption
Power Factor
Temperature Control
Dimensions (HWD)
Packaged Dimensions (HWD)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Outdoor Unit
Casing Color
Type
Compressor
Model
Motor Output
Model
Refrigerant
Oil
Charge
Model
Refrigerant
Charge
Fan
Note:
Specifications
kW
Btu/h
kcal/h
L/h
A
W
%
W/W
mm
mm
mm
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
Cooling
2.5 (1.3~3.0)
8,500 (4,400~10,200)
2,150 (1,110~2,580)
1.2
3.8
695 (300~920)
79.5
3.60
FVXS35BVMB
RXS35D(2)VMB
Heating
3.4 (1.3~4.5)
11,600 (4,400~15,350)
2,920 (1,110~3,870)
4.2
895 (290~1,390)
92.7
3.80
6.4
9.5
18.0
Both Liquid and Gas Pipes
FVXS25BVMB
Almond White
8.1 (286)
9.2 (325)
6.2 (219)
7.0 (247)
4.3 (152)
4.8 (169)
3.4 (120)
3.5 (124)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable / Washable / Mildew Proof
0.14
0.14
32
32
99.4
99.4
Microcomputer Control
600650195
714770294
13
19
Cooling
3.5 (1.4~3.8)
11,900 (4,750~12,950)
3,010 (1,200~3,260)
1.9
5.0
1,090 (300~1,250)
94.8
3.21
6.4
9.5
18.0
Both Liquid and Gas Pipes
FVXS35BVMB
Almond White
8.3 (293)
9.2 (325)
6.3 (222)
7.1 (251)
4.3 (152)
5.0 (177)
3.4 (120)
3.6 (127)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable / Washable / Mildew Proof
0.14
0.14
32
32
99.4
99.4
Microcomputer Control
600650195
714770294
13
19
dBA
38 / 32 / 26 / 23
38 / 32 / 26 / 23
39 / 33 / 27 / 24
dBA
54
55
W
L
kg
H
L
W
A
W
%
A
mm
mm
kg
kg
RXS25D(2)VMB
Ivory White
Hermetically Sealed Swing Type
1YC23NXD#A
600
FVC50K
0.375
R410A
0.80
36.2 (1,278)
32.6 (1,151)
25.7 (907)
30.6 (1,080)
Propeller
31
3.66
4.06
663
863
78.8
92.4
4.2
550765285
589882363
30
35
Heating
4.5 (1.4~5.0)
15,350 (4,750~17,050)
3,870 (1,200~4,300)
6.0
1,320 (310~1,880)
95.7
3.41
39 / 33 / 26 / 23
RXS35D(2)VMB
Ivory White
Hermetically Sealed Swing Type
1YC23NXD#A
600
FVC50K
0.375
R410A
1.00
33.5 (1,183)
30.2 (1,066)
23.4 (826)
28.3 (999)
Propeller
35
4.86
5.86
1,058
1,288
94.7
95.6
6.0
550765285
589882363
32
38
dBA
46 / 43
47 / 44
47 / 44
dBA
61
62
62
3D049147
48 / 45
63
3D049148A
Conversion Formulae
kcal/h=kW860
Btu/h=kW3414
cfm=m/min35.3
Specifications
SiBE06-514
Specifications
SiBE06-514
Part 3
Printed Circuit Board
Connector Wiring Diagram
1. Printed Circuit Board Connector Wiring Diagram....................................8
1.1 Indoor Unit................................................................................................8
1.2 Outdoor Unit ...........................................................................................10
SiBE06-514
Indoor Unit
Connectors
1) S6
2) S23
3) S31, S32
4) S201, S203,
S7, S24, S26
5) S202, S204,
S8
6) S25
7) S301, S302
Note:
Other designations
1) V1
2) FU
3) LED11
4) LED12
5) LED14
PCB Detail
Varistor
FUSE
LED for operation
LED for timer
LED for Home Leave Operation
PCB1
S202
S8
S204
2P044051F
SiBE06-514
PCB Detail
Pb Free
S25
S302
S301
SW2
S6
Pb Free
S23
PCB 3
S26
JA
SW4
JB
JC
S21
S24
LED 14
PCB 2
PCB 4
S201
LED 12
Pb Free
SW1
LED 11
LED A
S203
S32
S31
S7
V1
FU
2P088265D
1.2
SiBE06-514
Outdoor Unit
Connectors
1)
2)
3)
4)
5)
6)
7)
8)
Other designations
1)
2)
3)
4)
5)
10
S10
S11
S20
S30
S40
S70
S80
S90
FU1, FU2
FU3
LED A
V1, V2, V3
J8
Fuse (3.15A)
Fuse (20A)
Service monitor LED
Varistor
Facility setting jumper
Refer to page 43 for detail.
SiBE06-514
PCB Detail
FU3(20A)
S11
(R4293)
S40 LED A
S90
S30
S70
J8
HC3
FU2(3.15A)
HN3
HC4
S20
S80
V1
FU1(3.15A) HL3
(R4605)
11
12
SiBE06-514
SiBE06-514
Part 4
Function and Control
1. Main Functions......................................................................................14
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
Frequency Principle................................................................................14
Flap Control............................................................................................16
Air Flow Selection...................................................................................17
Fan Speed Control for Indoor Units........................................................18
Programme Dry Function .......................................................................19
Automatic Operation...............................................................................20
Thermostat Control.................................................................................21
NIGHT SET Mode ..................................................................................22
HOME LEAVE Operation .......................................................................23
Inverter POWERFUL Operation .............................................................24
Other Functions......................................................................................25
13
Main Functions
SiBE06-514
1. Main Functions
Note:
1.1
See the list of functions for the functions applicable to different models.
Frequency Principle
Main Control
Parameters
The compressor is frequency-controlled during normal operation. The target frequency is set by
the following 2 parameters coming from the operating indoor unit:
The load condition of the operating indoor unit
The difference between the room temperature and the set temperature
Additional
Control
Parameters
Inverter Principle
To regulate the capacity, a frequency control is needed. The inverter makes it possible to vary
the rotation speed of the compressor. The following table explains the conversion principle:
Phase
1
2
Drawing of
Inverter
Description
The supplied AC power source is converted into the DC power source for the present.
The DC power source is reconverted into the three phase AC power source with variable
frequency.
When the frequency increases, the rotation speed of the compressor increases resulting
in an increased refrigerant circulation. This leads to a higher amount of the heat
exchange per unit.
When the frequency decreases, the rotation speed of the compressor decreases
resulting in a decreased refrigerant circulation. This leads to a lower amount of the heat
exchange per unit.
DC
power
Amount of heat
exchanged air (small)
high speed
AC
power
Amount of heat
exchanged air (large)
high f
low f
Amount of heat
exchanged air (large)
Amount of heat
exchanged air (small)
low speed
50 Hz
freq=
constant 60 Hz
freq=variable
capacity=
variable
14
(R2812)
SiBE06-514
Inverter Features
Main Functions
45C
inverter
Start
60
120
300
seconds
(R1187)
Even during extreme cold weather, the high capacity is achieved. It is maintained even when
the outdoor air temperature is 2C.
Comfortable air conditioning
A detailed adjustment is integrated to ensure a fixed room temperature. It is possible to air
condition with a small room temperature variation.
Energy saving heating and cooling
Once the set temperature is reached, the energy saving operation enables to maintain the
room temperature at low power.
Frequency Limits
The following table shows the functions that define the minimum and maximum frequency:
Frequency limits
Low
High
Forced Cooling
Operation
15
Main Functions
1.2
SiBE06-514
Flap Control
Wide-angle Flap
The large flaps send a large volume of air all over the room. The flap provides an optimum
control in cooling, heating and dry mode.
Louvres
The louvres, made of elastic synthetic resin, provide a wide range of airflow that guarantees a
comfortable air distribution.
Auto-swing
The following table explains the auto-swing process for heating and cooling:
Item
heating
Description
Drawing
(R1194)
cooling /
dry
(R1195)
16
SiBE06-514
1.3
Main Functions
Air conditioner automatically decides the appropriate blowing pattern depending on the
operating mode / situation.
Operating mode
Cool mode
Situation
Blowing pattern
When the room has become
So that air does not come into direct contact
fully cool, or when one hour has
with people, air is blown upper air outlet,
passed since turning on the air
room temperature is equalised.
conditioner.
Heat mode
Air is blown
from the upper
and lower air
outlets for high
speed cooling
during Cool
mode, and for
filling the room
with warm air
during Heat
mode.
At start or when air temperature So that air does not come into direct contact
is low.
with people. Air is blown upper air outlet.
During Dry mode, so that cold air does not come into direct contact with people, air is blown
upper air outlet.
Regardless of the operating mode or situation, air blows from the upper air outlet.
Use this switch when you do not want air coming out of the lower air outlet. (While sleeping
etc..)
17
Main Functions
1.4
SiBE06-514
Control Mode
The airflow rate can be automatically controlled depending on the difference between the set
temperature and the room temperature. This is done through phase control and Hall IC control.
For more information about Hall IC, refer to trouble shooting for fan motor on page 83.
Phase Steps
Phase control and fan speed control contains 9 steps: LLL, LL, SL, L, ML, M, MH, H and HH.
Step
Cooling
LLL
LL
SL (Silent)
L
ML
M
MH
H
HH (Powerful)
Heating
Dry mode
25 35kW class :
740 - 760 rpm
(During powerful operation :
970rpm)
(R4085)
(R4085)
= Within this range the airflow rate is automatically controlled when the FAN setting
button is set to automatic.
Note:
Automatic Air
Flow Control for
Heating
The following drawing explains the principle for fan speed control for heating:
Thermostat
setting
temperature
-0.5C
L
-1C
-1.5C
ML
-2C
M
fan speed
Automatic Air
Flow Control for
Cooling
(R4558)
The following drawing explains the principle of fan speed control for cooling:
fan speed
M
+2C
ML
+1.5C
L
+1C
+0.5C
Thermostat
setting
temperature
18
(R4559)
SiBE06-514
1.5
Main Functions
In Case of
Inverter Units
The microcomputer automatically sets the temperature and fan settings. The difference
between the room temperature at startup and the temperature set by the microcomputer is
divided into two zones. Then, the unit operates in the dry mode with an appropriate capacity for
each zone to maintain the temperature and humidity at a comfortable level.
Room temperature at
startup
temperature at
24C Room
startup
18C
Temperature difference
for operation stop
1.5C
0.5C
18C
1.0C
17C
ON point
Frequency
switching
point
0.5C
OFF point
5 min
5 min
Compressor
control
LHz
Stop
*55Hz
LHz
Stop
LHz
Stop
*55Hz
Stop
Stop
Low air flow
LHz indicates low frequency. Item marked with varies depending on models.
(R1359)
19
Main Functions
1.6
SiBE06-514
Automatic Operation
Automatic Cooling / Heating Function (Heat Pump Only)
When the AUTO mode is selected with the remote controller, the microcomputer automatically
determines the operation mode from cooling and heating according to the room temperature
and setting temperature at the time of the operation startup, and automatically operates in that
mode.
The unit automatically switches the operation mode to cooling or heating to maintain the room
temperature at the main unit setting temperature.
Detailed
Explanation of
the Function
2.5 deg.
or higher
(Heating thermostat
OFF point)
Main unit setting
temperature
(Cooling thermostat
OFF point)
Cooling /
heating switching point
(1.5 deg.)
or higher
Less than
(1.5 deg.)
Cooling
operation
Heating
operation
Cooling
operation
2.5 deg.
or higher
20
SiBE06-514
1.7
Main Functions
Thermostat Control
Thermostat control is based on the difference between the room temperature and the setpoint.
Thermostat OFF Condition
The temperature difference is in the zone A.
Thermostat ON Condition
The temperature difference is above the zone C after being in the zone A.
The system resumes from defrost control in any zones except A.
The operation turns on in any zones except A.
The monitoring time has passed while the temperature difference is in the zone B.
(Cooling / Dry : 10 minutes, Heating : 10 seconds)
Cooling / Dry
ON
C
B
Cooling : -2.0C
Dry : -2.5~-2.0C
A
OFF
(R4668)
Heating
Room temperature - setpoint
OFF
A
1.5C
B
C
0C
ON
(R4669)
21
Main Functions
1.8
SiBE06-514
The Night Set circuit continues heating or cooling the room at the set temperature for the first
one hour, then automatically raises the temperature setting slightly in the case of cooling, or
lowers it slightly in the case of heating, for economical operations. This prevents excessive
heating in winter and excessive cooling in summer to ensure comfortable sleeping conditions,
and also conserves electricity.
Cooling Operation
A
0.5C
1 hour
Timer operation
Night Set Circuit ON
A
B
30 minutes
+0.5C
temperature shift
Temperature
setting +1C
Temperature
setting +0.5C
B
Temperature
setting
Operation stops
at the set hours
0.5C
Heating Operation
2C
Thermostat
setting
Timer operation
Night Set Circuit ON
22
1 hour later
(R1362)
SiBE06-514
1.9
Main Functions
Outline
In order to respond to the customer's need for immediate heating and cooling of the room after
returning home or for house care, a measure to switch the temperature and air volume from that
for normal time over to outing time by one touch is provided. (This function responds also to the
need for keeping up with weak cooling or heating.)
This time, we seek for simplicity of operation by providing the special temperature and air
volume control for outing to be set by the exclusive button.
Detail of the
Control
1. Start of Function
The function starts when the [HOME LEAVE] button is pressed in cooling mode or heating
mode (including stopping and powerful operation). If this button is pressed while the operation is
stopped, the function becomes effective when the operation is started. If this button is pressed
in powerful operation, the powerful operation is reset and this function becomes effective.
The [HOME LEAVE] button is ineffective in dry mode and fan mode.
2. Details of Function
A mark representing [HOME LEAVE] is indicated on the liquid crystal display of the remote
controller. The indoor unit is operated according to the set temperature and air volume for
HOME LEAVE which were pre-set in the memory of the remote controller.
The LED (Red) of indoor unit representing [HOME LEAVE] lights up. (It goes out when the
operation is stopped.)
3. End of Function
The function ends when the [HOME LEAVE] button is pressed again during [HOME LEAVE]
operation or when the powerful operation button is pressed.
Scene <Cooling>
Home leave
operation
set temp.
Set temp.
Normal operation
Time
(R1366)
Scene <Heating>
Home leave
operation
set temp.
Set temp.
Normal operation
Time
Others
The set temperature and set air volume are memorized in the remote controller. When the
remote controller is reset due to replacement of battery, it is necessary to set the temperature
and air volume again for [HOME LEAVE].
23
Main Functions
SiBE06-514
In order to exploit the cooling and heating capacity to full extent, operate the air conditioner by
increasing the indoor fan rotating speed and the compressor frequency.
Details of the
Control
When POWERFUL button is pushed in each operation mode, the fan speed / setting
temperature will be converted to the following states in a period of twenty minutes.
Operation mode
COOL
DRY
Fan speed
H tap + 70 rpm
Dry rotating speed +
50 rpm
HEAT
FAN
AUTO
H tap + 80 rpm
H tap + 70 rpm
Same as cooling /
heating in Powerful
operation
18C
Powerful ON
Powerful OFF
Fan
70rpm
H tap
Set tap
20min.
(R4680)
24
SiBE06-514
Main Functions
ON / OFF button
(R3052)
Push this button once to start operation. Push once again to stop it.
This button is useful when the remote controller is missing.
The operation mode refers to the following table.
Cooling Only
Heat Pump
Mode
COOL
AUTO
Temperature setting
22C
25C
In the case of multi system operation, there are times when the unit does not activate with
this button.
25
Main Functions
SiBE06-514
26
SiBE06-514
Function of Thermistor
2. Function of Thermistor
2.1
C
Four way valve
Compressor
(R3305)
A Outdoor Heat
Exchanger
Thermistor (DCB)
1. The outdoor heat exchanger thermistor is used for controlling target discharge temperature.
The system sets a target discharge temperature according to the outdoor and indoor heat
exchanger temperature, and controls the electronic expansion valve opening so that the
target discharge temperature can be obtained.
2. The outdoor heat exchanger thermistor is used for detecting disconnection of the discharge
thermistor when cooling.
When the discharge pipe temperature becomes lower than the outdoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
3. The outdoor heat exchanger thermistor is used for high pressure protection during cooling
operation.
B Discharge
Pipe Thermistor
(DOT)
1. The discharge pipe thermistor is used for controlling temperature of the discharge pipe.
If the temperature of discharge pipe (used in place of the inner temperature of the
compressor) rises abnormally, the operating frequency drops or the operation halts.
2. The discharge pipe thermistor is used for detecting disconnection of the discharge
thermistor.
C Indoor Heat
Exchanger
Thermistor (DCN)
1. The indoor heat exchanger thermistor is used for controlling target discharge temperature.
The system sets a target discharge temperature according to the outdoor and indoor heat
exchanger temperature, and controls the electronic expansion valve opening so that the
target discharge temperature can be obtained.
2. The indoor heat exchanger thermistor is used for preventing freezing.
During the cooling operation, if the temperature drops abnormally, the operating frequency
becomes lower, then the operation halts.
3. The indoor heat exchanger thermistor is used for anti-icing control.
During the cooling operation, if the heat exchanger temperature in the room where operation
is halted becomes -1C, it is assumed as icing.
4. During heating, the indoor heat exchanger thermistor is used for detecting disconnection of
the discharge pipe thermistor.
When the discharge pipe temperature becomes lower than the indoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
27
Function of Thermistor
2.2
SiBE06-514
Compressor
(R2828)
A Outdoor Heat
Exchanger
Thermistor (DCB)
1. The outdoor heat exchanger thermistor is used for controlling target discharge temperature.
The system sets a target discharge temperature according to the outdoor and indoor heat
exchanger temperature, and controls the electronic expansion valve opening so that the
target discharge temperature can be obtained.
2. The outdoor heat exchanger thermistor is used for detecting disconnection of the discharge
thermistor when cooling.
When the discharge pipe temperature becomes lower than the outdoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
3. The outdoor heat exchanger thermistor is used for high pressure protection during cooling
operation.
B Discharge
Pipe Thermistor
(DOT)
1. The discharge pipe thermistor is used for controlling temperature of the discharge pipe.
If the temperature of discharge pipe (used in place of the inner temperature of the
compressor) rises abnormally, the operating frequency drops or the operation halts.
2. The discharge pipe thermistor is used for detecting disconnection of the discharge
thermistor.
C Indoor Heat
Exchanger
Thermistor (DCN)
1. The indoor heat exchanger thermistor is used for controlling target discharge temperature.
The system sets a target discharge temperature according to the outdoor and indoor heat
exchanger temperature, and controls the electronic expansion valve opening so that the
target discharge temperature can be obtained.
2. The indoor heat exchanger thermistor is used for preventing freezing.
During the cooling operation, if the temperature drops abnormally, the operating frequency
becomes lower, then the operation halts.
3. The indoor heat exchanger thermistor is used for anti-icing control.
During the cooling operation, if the heat exchanger temperature in the room where operation
is halted becomes -1C, it is assumed as icing.
28
SiBE06-514
Control Specification
3. Control Specification
3.1
Mode Hierarchy
Outline
There are two modes; the mode selected in users place (normal air conditioning mode) and
forced operation mode for installation and providing service.
Detail
Note:
Unless specified otherwise, an indoor dry operation command must be regarded as cooling
operation.
29
Control Specification
3.2
Outline
SiBE06-514
Frequency Control
Frequency will be determined according to the difference between room and set temperature.
The function is explained as follows.
1. How to determine frequency.
2. Frequency command from an indoor unit. (The difference between a room temperature and
the temperature set by the remote controller.)
3. Frequency command from an indoor unit.
4. Frequency initial setting.
5. PI control.
Frequency changes by PI control < repeats when frequency becomes lower
Command frequency X repeats when frequency becomes lower
Drooping function
Input current control, etc.
Upper limit frequency
FMAX
Command frequency
Limit frequency
Initial frequency
PI control
Defrost control (*)
Skip control
Target frequency
(R2831)
Detail
30
SiBE06-514
Control Specification
D
signal
Th
OFF
1
2
3
Temperature
difference
2.0
D
signal
4
Temperature
difference
4.0
D
signal
8
Temperature
difference
6.0
D
signal
C
2.5
3.0
3.5
5
6
7
4.5
5.0
5.5
9
A
B
6.5
7.0
7.5
D
E
F
31
Control Specification
3.3
SiBE06-514
Operate the inverter in the open phase operation with the conditions including the preheating
command from the discharge pipe temperature.
Detail
Preheating ON Condition
When the discharge pipe temperature is below 10C, inverter in open phase operation
starts.
OFF Condition
When the discharge pipe temperature is higher than 12C, inverter in open phase operation
stops.
Detail
Detail
Starting Conditions
1. When starting compressor for heating.
2. When the operating mode changes to cooling from heating.
3. When starting compressor for rushing defrosting or resetting.
4. When starting compressor for the first time after the reset with the power is ON.
5. When starting compressor for heating next to the suspension of defrosting.
6. When starting compressor next to the fault of switching over cooling / heating.
Set the lower limit frequency (cooling : 68Hz, heating : 66Hz) for 45 seconds with any conditions
1 through 4 above.
32
SiBE06-514
Control Specification
3.4
Frequency
88
64
48
240
360
180
FCG3
FCG2
FCG1
TCG1sec
TCG2sec
TCG3sec
Time
(R2949)
Outline
The discharge pipe temperature is used as the compressor's internal temperature. If the
discharge pipe temperature rises above a certain level, the operating frequency upper limit is
set to keep this temperature from going up further.
Detail
Drooping zone
Keep zone
99C
Up zone
Heat exchanger
thermistor
temperature
Control contents
When the temperature reaches the stop zone, stop the compressor and
correct abnormality.
Start the timer, and the frequency will be drooping.
Keep the upper limit of frequency.
Cancel the upper limit of frequency.
33
Control Specification
3.5
Outline
SiBE06-514
Detail
Compressor Stop
I4
Stop Zone
I3
Drooping Zone
I3 I
Keep Zone
Reset Zone
(R4304)
I4
(A)
I3
(A)
I3-I (A)
Cooling
25 class
35 class
12
6.0
7.25
5.25
6.5
Heating
25 class
35 class
12
7.5
8.25
6.75
7.5
Limitation of current drooping and stop value according to the outdoor air temperature
1. In case the operation mode is cooling
The current droops when outdoor air temperature becomes higher than a certain level
(model by model).
2. In case the operation mode is heating (only for heat pump model)
The current droops when outdoor air temperature becomes higher than a certain level
(model by model).
34
SiBE06-514
3.6
Control Specification
Outline
During cooling operation, the signals being sent from the indoor unit allow the operating
frequency limitation and then prevent freezing of the indoor heat exchanger. (The signal from
the indoor unit must be divided into the zones as the followings.
Detail
13C
Reset zone
7C
Up zone
5C
Keep zone
3C
0C
Drooping zone
Stop zone
(R4561)
3.7
Outline
Detail
Drooping zone
Keep zone
Up zone
Reset zone 46C
(R4589)
35
Control Specification
3.8
SiBE06-514
Fan Control
Outline
Detail
3.9
Outline
In order to obtain the dependability of the compressor, the compressor must be stopped
according to the conditions of the temperature of the outdoor air and outdoor heat exchanger.
Detail
36
SiBE06-514
Control Specification
Detail
Frequency
PI control
0Hz
60sec.
50sec.
Compressor
600sec.
50sec.
ON
OFF
ON
OFF
5sec.
5sec.
Fan
ON
OFF
Electronic expansion
valve opening
450pps
350pps
450pps
Initial opening
(R4014)
37
Control Specification
SiBE06-514
Detail
The followings are the examples of control which function in each mode by the electronic
expansion valve control.
Control for abnormally high discharge
pipe temperature
The following items are included in the electronic expansion valve control.
Electronic expansion valve is fully closed
1. Electronic expansion valve is fully closed when turning on the power.
2. Pressure equalizing control
Open Control
1. Electronic expansion valve control when starting operation
2. Control when frequency changed
3. Control for defrosting (only for heat pump model)
4. Control when a discharge pipe temperature is abnormally high
5. Control when the discharge pipe thermistor is disconnected
Feedback Control
1. Discharge pipe temperature control
Outline
Continue
Operation pattern
: function
: not function
When power is turned ON
Cooling operation
Stop
Heating operation
(only for heat
pump model)
Stop
Heating operation
(only for heat
pump model)
Control of discharge pipe
thermistor disconnection
Stop
(R2833)
38
SiBE06-514
Control Specification
Detail
Detect a disconnected discharge pipe thermistor by comparing the discharge pipe temperature
with the condensation temperature. If any is disconnected, open the electronic expansion valve
according to the outdoor air temperature and the operating frequency and operate for a
specified time, and then stop.
After 3 minutes of waiting, restart the unit and check if any is disconnected. If any is
disconnected stop the system after operating for a specified time. If the disconnection is
detected 4 times in succession, then the system will be down.
Detail
Detect Disconnection
If the timer for open control (cooling : 13min., heating : 15min.) becomes over, and the 9-minute
timer for the compressor operation continuation is not counting time, the following adjustment
must be made.
1. When the operation mode is cooling
When the discharge pipe temperature is lower than the outdoor heat exchanger
temperature, the discharge pipe thermistor disconnection must be ascertained.
2. When the operation mode is heating (only for heat pump model)
When the discharge pipe temperature is lower than the max temperature of indoor unit heat
exchanger, the discharge pipe thermistor disconnection must be ascertained.
Adjustment when the thermistor is disconnected
When compressor stop repeats specified time, the system should be down.
39
Control Specification
SiBE06-514
SC
SH
Determine a correction value of the electronic expansion valve compensation and drive it
according to the deflection of the target discharge temperature and actual discharge
temperature, and the discharge temperature variation by the 20 sec.
40
SiBE06-514
Control Specification
3.12 Malfunctions
3.12.1 Sensor Malfunction Detection
Sensor malfunction may occur in the thermistor.
Relating to Thermistor Malfunction
1. Outdoor heat exchanger thermistor
2. Discharge pipe thermistor
3. Fin thermistor
4. Outdoor air thermistor
In order to protect the inverter, detect an excessive output current, and for protecting
compressor, monitor the OL operation.
Detail
Power consumption
55 Hz
Frequency
(R2834)
Gas insufficient
zone
(R1391)
41
Control Specification
Detail
SiBE06-514
Cooling
Heating
4.0C
4.0C
3.0C
3.0C
Detail
Forced Cooling
Item
Forced operation
allowing conditions
Starting/adjustment
1) Command
frequency
2) Electronic
expansion valve
opening
3) Outdoor unit
adjustment
4) Indoor unit
adjustment
End
Others
Forced Cooling
1) The outdoor unit is not abnormal
and not in the 3-minute stand-by
mode.
2) The operating mode of the outdoor
unit is the stop mode.
3) The forced operation is ON.
The forced operation is allowed when
the above and conditions are met.
If the forced operation switch is
pressed as the above conditions are
met.
68 Hz
It depends on the capacity of the
indoor unit.
Compressor is in operation.
The command of forced operation is
transmitted to the indoor unit.
1) When the forced operation switch is
pressed again.
2) The operation is to end
automatically after 15 min.
The protect functions are prior to all
others in the forced operation.
42
SiBE06-514
Control Specification
This function is limited only for facilities (the target of air conditioning is equipment (such as
computer)). Never use it in a residence or office (the space where there is a human).
Detail
You can expand the operation range to 15C by cutting jumper 8 (J8) on the PCB. If the
outdoor temperature falls to 20C or lower, the operation will stop. If the outdoor temperature
rises, the operation will start again.
S90
S70
PCB
S80
J8
J7
J6
J5
J4
J3
J1
Caution
1. If the outdoor unit is installed where the heat exchanger of the unit is exposed to direct wind,
provide a windbreak wall.
2. Intermittent noises may be produced by the indoor unit due to the outdoor fan turning on and
off when using facility settings.
3. Do not place humidifiers or other items which might raise the humidity in rooms where facility
settings are being used.
A humidifier might cause dew jumping from the indoor unit outlet vent.
4. Cutting jumper 8 (J8) sets the indoor fan tap to the highest position. Notify the user about
this.
43
Control Specification
44
SiBE06-514
SiBE06-514
Part 5
System Configuration
1. System Configuration............................................................................46
2. Instruction..............................................................................................47
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
System Configuration
Safety precautions..................................................................................47
Names of parts .......................................................................................49
Preparation before Operation.................................................................52
AUTO DRY COOL HEAT FAN Operation ......................................55
Adjusting the Air Flow Direction .............................................................57
POWERFUL Operation ..........................................................................59
OUTDOOR UNIT SILENT Operation ....................................................60
HOME LEAVE Operation .......................................................................61
TIMER Operation ...................................................................................63
Care and Cleaning .................................................................................65
Troubleshooting......................................................................................68
45
System Configuration
SiBE06-514
1. System Configuration
After the installation and test operation of the room air conditioner have been completed, it
should be operated and handled as described below. Every user would like to know the correct
method of operation of the room air conditioner, to check if it is capable of cooling (or heating)
well, and to know a clever method of using it.
In order to meet this expectation of the users, giving sufficient explanations taking enough time
can be said to reduce about 80% of the requests for servicing. However good the installation
work is and however good the functions are, the customer may blame either the room air
conditioner or its installation work because of improper handling. The installation work and
handing over of the unit can only be considered to have been completed when its handling has
been explained to the user without using technical terms but giving full knowledge of the
equipment.
46
System Configuration
SiBE06-514
Instruction
2. Instruction
2.1
Safety precautions
Safety precautions
Keep this manual where the operator can easily find them.
Read this manual attentively before starting up the unit.
For safety reason the operator must read the following cautions carefully.
This manual classifies precautions into WARNINGS and CAUTIONS. Be sure to follow all precautions below: they are
all important for ensuring safety.
WARNING
CAUTION
Never do.
WARNING
In order to avoid fire, explosion or injury, do not operate the unit when harmful, among which flammable or
corrosive gases, are detected near the unit.
It is not good for health to expose your body to the air flow for a long time.
Do not put a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a high speed, it will
cause injury.
Do not attempt to repair, relocate, modify or reinstall the air conditioner by yourself. Incorrect work will cause electric
shocks, fire etc.
For repairs and reinstallation, consult your Daikin dealer for advice and information.
The refrigerant used in the air conditioner is safe. Although leaks should not occur, if for some
reason any refrigerant happens to leak into the room, make sure it does not come in contact
with any flame as of gas heaters, kerosene heaters or gas range.
If the air conditioner is not cooling (heating) properly, the refrigerant may be leaking, so call your dealer.
When carrying out repairs accompanying adding refrigerant, check the content of the repairs with our service staff.
Do not attempt to install the air conditioner by your self. Incorrect work will result in water leakage, electric shocks or
fire. For installation, consult the dealer or a qualified technician.
In order to avoid electric shock, fire or injury, if you detect any abnormally such as smell of fire, stop the operation and
turn off the breaker. And call your dealer for instructions.
CAUTION
The air conditioner must be earthed. Incomplete earthing may result in electric shocks. Do not connect the
earth line to a gas pipe, water pipe, lightning rod, or a telephone earth line.
In order to avoid any quality deterioration, do not use the unit for cooling precision instruments, food, plants,
animals or works of art.
Never expose little children, plants or animals directly to the air flow.
Do not place appliances which produce open fire in places exposed to the air flow from the unit or under the
indoor unit. It may cause incomplete combustion or deformation of the unit due to the heat.
Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.
System Configuration
47
Instruction
SiBE06-514
Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not remove the fan guard.
Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In certain conditions,
moisture in the air may condense and drip.
After a long use, check the unit stand and fittings for damage.
Do not touch the air inlet and alminum fins of outdoor unit. It may cause injury.
The appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not play with the appliance.
To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is used together with
the air conditioner.
Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply cord.
Do not connect the air conditioner to a power supply different from the one as specified. It may cause
trouble or fire.
Depending on the environment, an earth leakage breaker must be installed. Lack of an earth leakage breaker may
result in electric shocks.
Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the building, furniture
etc.
Do not operate the air conditioner with wet hands.
Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
Do not place things such as vessels containing water or anything else on top of the unit. Water may
penetrate into the unit and degrade electrical insulations, resulting in an electric shock.
Installation site
To install the air conditioner in the following types of environments, consult the dealer.
Places with an oily ambient or where steam or soot occurs.
Salty environment such as coastal areas.
Places where sulfide gas occurs such as hot springs.
Places where snow may block the outdoor unit.
The drain from the outdoor unit must be discharged to a place of good drainage.
Electrical work
For power supply, be sure to use a separate power circuit dedicated to the air conditioner.
System relocation
Relocating the air conditioner requires specialized knowledge and skills. Please consult the dealer if
relocation is necessary for moving or remodeling.
48
System Configuration
SiBE06-514
2.2
Instruction
Names of parts
Names of parts
Indoor Unit
1
3
10
7
6
ON
OFF
2
9
11
12 13
This setting is
recommended.
14
15
Air outlet
selection
CAUTION
Before opening the front grille, be sure to stop the operation and turn the breaker OFF.
Do not touch the metal parts on the inside of the indoor unit, as it may result in injury.
System Configuration
49
Instruction
SiBE06-514
Outdoor Unit
16
17
18
19
20
Indoor Unit
1. Photocatalytic deodorizing filter and
Air purifying filter:
These filters are attached to the inside of the air
filters.
2. Air outlet
3. Display
4. Front grille
5. Louvers (vertical blades): (page 12.)
The louvers are inside of the air outlet.
6. Air inlet
7. Air filter
8. Flap (horizontal blade): (page 12.)
9. Operation lamp (green)
10. TIMER lamp (yellow): (page 18.)
11. HOME LEAVE lamp (red): (page 16.)
12. Indoor Unit ON/OFF switch:
Push this switch once to start operation.
Push once again to stop it.
Outdoor Unit
50
System Configuration
SiBE06-514
Instruction
Remote control
1
ON
HOME LEAVE
ON/OFF
3
POWERFUL
TEMP
MODE
SILENT
FAN
4
7
SWING
9
10
CANCEL
14
8
11
ON
15
OFF
TIMER
12
13
System Configuration
8.
9.
10.
11.
12.
13.
14.
15.
51
Instruction
2.3
SiBE06-514
Position + and
correctly!
3
1
ATTENTION
About batteries
When replacing the batteries, use batteries of the same type, and replace the two old batteries
together.
When the system is not used for a long time, take the batteries out.
We recommend replacing once a year, although if the remote control display begins to fade or if
reception deteriorates, please replace with new alkali batteries. Using manganese batteries reduces
the lifespan.
The attached batteries are provided for the initial use of the system.
The usable period of the batteries may be short depending on the manufactured date of the air
conditioner.
52
System Configuration
SiBE06-514
Instruction
Receiver
Remote control
holder
Set.
ATTENTION
About remote control
Never expose the remote control to direct sunlight.
Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.
Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such as
inverter-type lamps) is in the room. Consult the shop if that is the case.
If the remote control signals happen to operate another appliance, move that appliance to
somewhere else, or consult the shop.
System Configuration
53
Instruction
SiBE06-514
blinks.
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
SWING
ON
CANCEL
1.3
OFF
TIMER
NOTE
Tips for saving energy
Be careful not to cool (heat) the room too much.
Keeping the temperature setting at a moderate level helps save energy.
Recommended temperature setting
Cover windows with a blind or a curtain.
For cooling: 26C 28C
Blocking sunlight and air from outdoors increases the cooling (heating) effect. For heating: 20C 24C
Clogged air filters cause inefficient operation and waste energy. Clean them
once in about every two weeks.
Please note
The air conditioner always consumes 15-35 watts of electricity even while it is not operating.
If you are not going to use the air conditioner for a long period, for example in spring or autumn, turn the breaker OFF.
Use the air conditioner in the following conditions.
Mode
Operating conditions
COOL
HEAT
DRY
Operation outside this humidity or temperature range may cause a safety device to disable the system.
54
System Configuration
SiBE06-514
2.4
Instruction
To start operation
HOME LEAVE
ON/OFF
: AUTO
POWERFUL
TEMP
MODE
SILENT
FAN
: DRY
2, 3
1
: COOL
: HEAT
: FAN
SWING
5
ON
<FVKS>
CANCEL
OFF
TIMER
<FVXS>
ON
OFF
To stop operation
3. Press ON/OFF button again.
The OPERATION lamp goes off.
System Configuration
55
Instruction
SiBE06-514
to
are available.
NOTE
Note on HEAT operation
Since this air conditioner heats the room by taking heat from outdoor air to indoors, the heating
capacity becomes smaller in lower outdoor temperatures. If the heating effect is insufficient, it is
recommended to use another heating appliance in combination with the air conditioner.
The heat pump system heats the room by circulating hot air around all parts of the room. After the
start of heating operation, it takes some time before the room gets warmer.
In heating operation, frost may occur on the outdoor unit and lower the heating capacity. In that
case, the system switches into defrosting operation to take away the frost.
During defrosting operation, hot air does not flow out of indoor unit.
At the start of heater operation, so that air does not blow directly on an individual, air blows in an
upward direction. After the blowing air gets warmer, the air will blow according to memorised air flow
direction and rates.
Note on DRY operation
The computer chip works to rid the room of humidity while maintaining the temperature as
much as possible. It automatically controls temperature and fan strength, so manual
adjustment of these functions is unavailable.
Note on AUTO operation
In AUTO operation, the system selects a temperature setting and an appropriate operation mode
(COOL or HEAT) based on the room temperature at the start of the operation.
The system automatically reselects setting at a regular interval to bring the room temperature to
usersetting level.
If you do not like AUTO operation, you can manually select the operation mode and setting
you like.
Note on air flow rate setting
At smaller air flow rates, the cooling (heating) effect is also smaller.
56
System Configuration
SiBE06-514
2.5
Instruction
ON
C
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
ON
SWING
1, 2
CANCEL
OFF
TIMER
System Configuration
COOL/DRY
HEAT
57
Instruction
SiBE06-514
Air conditioner automatically decides the appropriate blowing pattern depending on the operating
mode/situation.
Operating mode
COOL mode
Situation
Blowing pattern
HEAT mode
During Dry mode, so that cold air does not come into direct contact with people, air is blown upper air outlet.
Regardless of the operating mode or situation, air blows from the upper air outlet.
Use this switch when you do not want air coming out of the lower air outlet. (While sleeping etc..)
CAUTION
Do not try to adjust the flap by hand.
When adjusting by hand, the mechanism may not operate properly or condensation may drip from
air outlets.
58
System Configuration
SiBE06-514
2.6
Instruction
POWERFUL Operation
POWERFUL Operation
POWERFUL operation quickly maximizes the cooling
(heating) effect in any operation mode. You can get the
maximum capacity .
To start POWERFUL
operation
ON
To cancel POWERFUL
operation
HOME LEAVE
POWERFUL
ON/OFF
TEMP
1, 2
MODE
SILENT
FAN
ON
SWING
CANCEL
OFF
TIMER
NOTE
Notes on POWERFUL operation
In COOL and HEAT mode
To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased
and the air flow rate be fixed to the maximum setting.
The temperature and air flow settings are not variable.
In DRY mode
The temperature setting is lowered by 2.5C and the air flow rate is slightly increased.
In FAN mode
The air flow rate is fixed to the maximum setting.
System Configuration
59
Instruction
2.7
SiBE06-514
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
SWING
1, 2
ON
CANCEL
OFF
TIMER
NOTE
Note on OUTDOOR UNIT SILENT operation
This function is available in COOL, HEAT, and AUTO modes.
(This is not available in FAN and DRY mode.)
POWERFUL operation and OUTDOOR UNIT SILENT operation cannot be used at the
same time.
Priority is given to POWERFUL operation.
If operation is stopped using the remote controller or the main unit ON/OFF switch when
using OUTDOOR UNIT SILENT operation,
will remain on the remote controller
display.
60
System Configuration
SiBE06-514
2.8
Instruction
ON
OFF
1, 2
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
ON
SWING
CANCEL
OFF
TIMER
Selectable range
temperature
temperature
Cooling
25C
AUTO
18-32C
Heating
25C
AUTO
10-30C
System Configuration
61
Instruction
SiBE06-514
Before bed...
NOTE
Once the temperature and air flow rate for HOME LEAVE operation are set, those settings will be
used whenever HOME LEAVE operation is used in the future. To change these settings, please refer
to the Before using HOME LEAVE operation section above.
HOME LEAVE operation is only available in COOL and HEAT mode. Cannot be used in AUTO, DRY,
and FAN mode.
HOME LEAVE operation runs in accordance with the previous operation mode (COOL or HEAT)
before using HOME LEAVE operation.
HOME LEAVE operation and POWERFUL operation cannot be used at the same time.
Last button that was pressed has priority.
The operation mode cannot be changed while HOME LEAVE operation is being used.
When operation is shut off during HOME LEAVE operation, using the remote control or the indoor
unit ON/OFF switch, will remain on the remote control display.
62
System Configuration
SiBE06-514
2.9
Instruction
TIMER Operation
TIMER Operation
Timer functions are useful for automatically switching the
air conditioner on or off at night or in the morning. You can
also use OFF TIMER and ON TIMER in combination.
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
blinks.
ON
SWING
CANCEL
OFF
TIMER
4
2
1, 3
ON
OFF
Notes
When TIMER is set, the present time is not displayed.
Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is canceled when
remote control batteries are replaced.)
When operating the unit via the ON/OFF Timer, the actual length of operation may vary from the time
entered by the user. (Maximum approx. 10 minutes)
NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically adjusts the temperature setting (0.5C
up in COOL, 2.0C down in HEAT) to prevent excessive cooling (heating) for your pleasant sleep.
System Configuration
63
Instruction
SiBE06-514
blinks.
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
SWING
1, 3
4
CANCEL
OFF
ON
OFF
TIMER
To cancel ON TIMER
operation
4. Press CANCEL button.
The TIMER lamp goes off.
Display
(Example)
Present time: 11:00 PM
(The unit operating)
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
Combined
ATTENTION
In the following cases, set the timer again.
After a breaker has turned OFF.
After a power failure.
After replacing batteries in the remote control.
64
System Configuration
SiBE06-514
Instruction
Units
Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
Front grille
1. Open the front grille.
Press the two
the front grille.
P U S H
Chain
CAUTION
System Configuration
65
Instruction
SiBE06-514
Filters
1. Open the front grille. (page 22)
Air Filter
1. Wash the air filters with water or clean them with
vacuum cleaner.
If the dust does not come off easily, wash them with neutral detergent
thinned with lukewarm water, then dry them up in the shade.
It is recommended to clean the air filters every two weeks.
[Replacement]
1. Detach the filter element and attach a new one.
66
System Configuration
SiBE06-514
Instruction
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult the
service shop if this is the case.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote control.
NOTE
Operation with dusty air filters lowers the cooling (heating) capacity and wastes energy.
Air is also prevented from flowing smoothly through the unit creating a noise.
Operation with dirty filters:
(1) cannot deodorize the air.
(2) cannot clean the air.
(3) results in poor heating or cooling.
(4) may cause odour.
The air purifying filter and Photocatalytic deodorizing filter cannot be reused, even if washed.
In principle, there is no need to replace the photocatalytic deodorizing filter. Remove the dust
periodically with a vacuum cleaner. However, it is recommended to replace the filter in the
following cases.
(1) The paper material is torn or broken during cleaning.
(2) The filter has become extremely dirty after long use.
To order air purifying filter or Photocatalytic deodorizing filter, contact to the service shop where
you bought the air conditioner.
Dispose of old air filters as non-burnable waste and Photocatalytic deodorizing filters as
burnable waste.
Item
Part No.
KAZ917B41
KAZ917B42
KAF925B41
KAF925B42
System Configuration
67
Instruction
SiBE06-514
2.11 Troubleshooting
Trouble Shooting
These cases are not troubles.
The following cases are not air conditioner troubles but have some reasons. You may just continue using it.
Case
Explanation
In HEAT mode
The frost on the outdoor unit melts into water or steam
when the air conditioner is in defrost operation.
In COOL or DRY mode
Moisture in the air condenses into water on the cool
surface of outdoor unit piping and drips.
This happens when the air in the room is cooled into mist by
the cold air flow during cooling operation.
The indoor unit gives out odour. This happens when smells of the room, furniture, or
cigarettes are absorbed into the unit and discharged with the
air flow.
(If this happens, we recommend you to have the indoor unit
washed by a technician. Consult the service shop where you
bought the air conditioner.)
68
System Configuration
SiBE06-514
Instruction
Check again.
Please check again before calling a repair person.
Case
The air conditioner does not
operate.
(OPERATION lamp is off)
Check
An abnormal functioning
happens during operation.
System Configuration
69
Instruction
SiBE06-514
WARNING
When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.
Continued operation in an abnormal condition may result in troubles, electric shocks or fire.
Consult the service shop where you bought the air conditioner.
Do not attempt to repair or modify the air conditioner by yourself.
Incorrect work may result in electric shocks or fire.
Consult the service shop where you bought the air conditioner.
If one of the following symptoms takes place, call the service shop immediately.
The power cord is abnormally hot or damaged.
An abnormal sound is heard during operation.
The safety breaker, a fuse, or the earth leakage breaker
cuts off the operation frequently.
A switch or a button often fails to work properly.
There is a burning smell.
Water leaks from the indoor unit.
After a power failure
The air conditioner automatically resumes
operation in about 3 minutes. You should just
wait for a while.
Lightning
If lightning may strike the neighbouring area,
stop operation and turn the breaker OFF for
system protection.
Disposal requirements
Your air conditioning product is marked with this symbol. This means that electrical and
electronic products shall not be mixed with unsorted household waste.
Do not try to dismantle the system yourself: the dismantling of the air conditioning
system, treatment of the refrigerant, of oil and of other parts must be done by a
qualified installer in accordance with relevant local and national legislation.
Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By
ensuring this product is disposed of correctly, you will help to prevent potential negative consequences
for the environment and human health. Please contact the installer or local authority for more
information.
Batteries must be removed from the remote control and disposed of separately in accordance with
relevant local and national legislation.
70
System Configuration
SiBE06-514
Instruction
Fault diagnosis
FAULT DIAGNOSIS BY REMOTE CONTROL
In the ARC433A series, the temperature display sections on the main unit indicate corresponding codes.
1. When the TIMER CANCEL button is held down for 5 seconds, a
the temperature display section.
indication flashes on
ON
C
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
ON
SWING
CANCEL
OFF
TIMER
2. Press the TIMER CANCEL button repeatedly until a continuous beep is produced.
The code indication changes as shown below, and notifies with a long beep.
SYSTEM
INDOOR UNIT
OUTDOOR
UNIT
CODE
00
U0
U2
U4
A1
A5
A6
C4
C9
EA
E5
E6
E7
E8
F3
F6
H6
H8
H9
J3
J6
L4
L5
P4
MEANING
NORMAL
REFRIGERANT SHORTAGE
DROP VOLTAGE OR MAIN CIRCUIT OVERVOLTAGE
FAILURE OF TRANSMISSION (BETWEEN INDOOR UNIT AND OUTDOOR UNIT)
INDOOR PCB DEFECTIVENESS
HIGH PRESSURE CONTROL OR FREEZE-UP PROTECTOR
FAN MOTOR FAULT
FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
FAULTY SUCTION AIR TEMPERATURE SENSOR
COOLING-HEATING SWITCHING ERROR
OL STARTED
FAULTY COMPRESSOR START UP
DC FAN MOTOR FAULT
OPERATION HALT DUE TO DETECTION OF INPUT OVER CURRENT
HIGH TEMPERATURE DISCHARGE PIPE CONTROL
HIGH PRESSURE CONTROL (IN COOLING)
OPERATION HALT DUE TO FAULTY POSITION DETECTION SENSOR
CT ABNORMALITY
FAULTY SUCTION AIR TEMPERATURE SENSOR
FAULTY DISCHARGE PIPE TEMPERATURE SENSOR
FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
OUTPUT OVERCURRENT
FAULTY INVERTER CIRCUIT HEATSINK TEMPERATURE SENSOR
NOTE
1. A short beep and two consecutive beeps indicate non-corresponding codes.
2. To cancel the code display, hold the TIMER CANCEL button down for 5 seconds. The code
display also cancel itself if the button is not pressed for 1 minute.
3P098587-1L
System Configuration
71
Instruction
72
SiBE06-514
System Configuration
SiBE06-514
Part 6
Service Diagnosis
1.
2.
3.
4.
5. Check ..................................................................................................113
5.1 How to Check .......................................................................................113
Service Diagnosis
73
SiBE06-514
Location of
Operation Lamp
Air outlet
Air inlet
Air outlet
Display
OPERATION
lamp (green)
ON
OFF
(R2664)
Troubleshooting
with the LED
Indication
74
The outdoor unit has one green LED (LEDA) on the PCB. The flashing green LED indicates
normal condition of microcomputer operation.
Service Diagnosis
SiBE06-514
Check Item
Details of Measure
indication
Diagnosis by service port pressure
Check for insufficient gas.
and operating current
Large Operating Noise and Check the output voltage of the
Vibrations
power transistor.
Check the power transistor.
Service Diagnosis
Reference
Page
79
79
79
118
119
75
SiBE06-514
Check Method 1
1. When the timer cancel button is held down for 5 seconds, a 00 indication flashes on the
temperature display section.
<ARC433A5, A6>
(R2596)
2. Press the timer cancel button repeatedly until a continuous beep is produced.
The code indication changes in the sequence shown below, and notifies with a long beep.
No.
1
2
3
4
5
6
7
8
9
10
11
Note:
76
Code
OO
U4
F3
E6
L5
A6
E5
F6
C9
UO
E7
No.
12
13
14
15
16
17
18
19
20
21
22
Code
C7
H8
J3
A3
A1
C4
C5
H9
J6
UA
A5
No.
23
24
25
26
27
28
29
30
31
32
33
Code
HO
E1
P4
L3
L4
H6
H7
U2
UH
EA
AH
Service Diagnosis
SiBE06-514
Check Method 2
1. Enter the diagnosis mode.
Press the 3 buttons (TEMPs,TEMPt, MODE) simultaneously.
(R4272)
(R4273)
(R4274)
(R4275)
(R4276)
Service Diagnosis
77
SiBE06-514
(R4277)
(R4278)
78
Service Diagnosis
SiBE06-514
Troubleshooting
4. Troubleshooting
4.1
Indoor
Unit
Outdoor
Unit
00
U0H
U2
U4
UA
A1
A5
A6
C4
C7
C9
E1
E5H
E6H
E7
E8
EA
F3
F6
H0
H6
H8
H9
J3
J6
L3
L4
L5
P4
Normal
Reference
Page
Insufficient gas
110
Over-voltage detection
112
87
88
80
81
83
85
86
85
89
90
Compressor lock
91
DC fan lock
92
93
94
96
97
99
100
101
102
102
102
104
106
108
102
Service Diagnosis
79
Troubleshooting
4.2
SiBE06-514
Remote
Controller
Display
Method of
Malfunction
Detection
Malfunction
Decision
Conditions
Supposed
Causes
Troubleshooting
Caution
Is it normal?
NO
Correct connections.
YES
Replace PCBs.
(R1400)
Note:
80
Connector No.
Control PCB : S7, S201, S203
Power Supply PCB : S8, S202, S204
Service Diagnosis
SiBE06-514
4.3
Troubleshooting
Remote
Controller
Display
A5
Method of
Malfunction
Detection
Malfunction
Decision
Conditions
Supposed
Causes
Service Diagnosis
81
Troubleshooting
SiBE06-514
Troubleshooting
Caution
Check No.06
Refer to P.116
Is there any
short-circuit?
YES
NO
Check the intake air filter.
Is it very dirty?
YES
NO
Check the dust accumulation on
the indoor unit heat exchanger.
Is it very dirty?
YES
NO
Check No. 06
Indoor unit heat exchanger
thermistor check
Does it conform to
the thermistor characteristic
chart?
NO
YES
82
Service Diagnosis
SiBE06-514
4.4
Troubleshooting
Remote
Controller
Display
A6
Method of
Malfunction
Detection
The rotation speed detected by the Hall IC during fan motor operation is used to determine
abnormal fan motor operation.
Malfunction
Decision
Conditions
When the detected rotation speed is less than 50% of the H tap under maximum fan motor
rotation demand.
Supposed
Causes
Service Diagnosis
Operation halt due to short circuit inside the fan motor winding.
Operation halt due to breaking of wire inside the fan motor.
Operation halt due to breaking of the fan motor lead wires.
Operation halt due to faulty capacitor of the fan motor.
Detection error due to faulty indoor unit PCB (1).
83
Troubleshooting
SiBE06-514
Troubleshooting
Caution
Check No.01
Refer to P.113
Check No.02
Refer to P.113
NO
YES
Turn power ON and
operate fan.
Does it rotate?
YES
Check No.01
Check output of fan
motor connector
Is motor
power voltage
DC 200V
generated?
NO
Replace indoor
unit PCB (1) .
YES
Is motor
control power voltage
DC 15V
generated?
NO Check No.02
Check output of indoor
unit PCB (1)
YES
Turn off power supply and
disconnect fan motor
connector, then turn
power ON again.
Is motor control
power voltage DC 16V
generetad?
YES
Check No.01
Check output of fan
motor connector
Is rotation
number command
voltage DC 5V
generated?
Check No.01
Check output of fan
motor connector
Check No.01
Check output of fan
motor connector
Is rotation
number command pulse NO
generated?
YES
Is rotation
NO
number command pulse
generated?
YES
Replace indoor
unit PCB (1) .
Replace indoor
unit PCB (2) .
YES
NO
NO
Replace indoor
unit PCB (2).
(R1214)
84
Service Diagnosis
SiBE06-514
4.5
Troubleshooting
Remote
Controller
Display
Method of
Malfunction
Detection
The temperatures detected by the thermistors are used to determine thermistor errors.
Malfunction
Decision
Conditions
When the thermistor input is more than 4.96 V or less than 0.04 V during compressor
operation.
(reference)
When above about 212C (less than 120 ohms) or below about -50C (more than 1,860 kohms).
Note:
Supposed
Causes
Troubleshooting
Caution
Check No.06
Refer to P.116
Is it normal?
NO
YES
Check No. 06
Thermistor resistance check
Is it normal?
NO
YES
Service Diagnosis
85
Troubleshooting
4.6
SiBE06-514
Remote
Controller
Display
C7
Method of
Malfunction
Detection
The shutter open/close performance is detected by the limit switch attached on its structure. In
this way, the shutter drive motor and the shutter limit switch are checked for failure.
Malfunction
Decision
Conditions
When the shutter is open, the limit switch is closed, or vice versa.
Supposed
Causes
Troubleshooting
Caution
Check No.03
Refer to P.113
Foreign substance in
the shutter structure?
YES
NO
Check No. 03
Check the limit switch continuity.
NO
Replace the limit switch.
YES
Open the shutter and turn on the
power.
Shutter closed?
NO
YES
Shutter opening itself?
NO
Relay harness
broken or connector
disconnected?
NO
YES
YES
86
Service Diagnosis
SiBE06-514
4.7
Troubleshooting
Remote
Controller
Display
U4
Method of
Malfunction
Detection
The data received from the outdoor unit in indoor unit-outdoor unit signal transmission is
checked whether it is normal.
Malfunction
Decision
Conditions
When the data sent from the outdoor unit cannot be received normally, or when the content of
the data is abnormal.
Supposed
Causes
Troubleshooting
Caution
Check No.10
Refer to P.118
YES
NO
Check the outdoor unit's LED A.
Is LED A flashing?
NO
YES
Check the voltage of the indoor
unit-outdoor unit connection wires
between No. 1 and No. 2, and
between No 2 and No. 3.
Is the voltage 0 V?
YES
NO
Check No. 10
Check power supply waveform.
NO
Service Diagnosis
87
Troubleshooting
4.8
SiBE06-514
Remote
Controller
Display
UA
Method of
Malfunction
Detection
The supply power is detected for its requirements (different from pair type and multi type) by the
indoor / outdoor transmission signal.
Malfunction
Decision
Conditions
Supposed
Causes
Troubleshooting
PCB).
Caution
(Q0347)
NO
YES
Check the code numbers
(2P01234, for example) of the
indoor and outdoor unit PCB
with the Parts List.
Matched compatibly?
YES
NO
88
Service Diagnosis
SiBE06-514
4.9
Troubleshooting
Remote
Controller
Display
E1
Method of
Malfunction
Detection
The system follows the microprocessor program to make sure it runs normally.
The system checks to see if the zero-cross signal comes in properly.
Malfunction
Decision
Conditions
Supposed
Causes
Troubleshooting
PCB).
Caution
(Q0347)
Is LED A flashing?
NO
YES
Check to see if the system is
grounded.
Grounded?
NO
YES
Is the harness
broken?
YES
NO
Zero-cross signal
abnormality. Replace the
outdoor unit PCB (2).
Replace the harness.
(R4563)
Service Diagnosis
89
Troubleshooting
SiBE06-514
E5
Method of
Malfunction
Detection
Malfunction
Decision
Conditions
Supposed
Causes
Refrigerant shortage
Four way valve malfunctioning
Outdoor unit PCB defective
Water mixed in the local piping
Electronic expansion valve defective
Stop valve defective
Troubleshooting
Caution
Check No.04
Refer to P.114
Discharge pipe thermistor
disconnected?
Check No.05
Refer to P.115
Malfunctioning
Discharge pipe thermistor
Functioning
Check No. 04
Check the electronic expantion
valve.
Check No.11
Refer to P.118
NO
Check No. 06
Check the thermistors
Check No.06
Refer to P.116
YES
Malfunctioning
Replace the valve itself or
the coil.
Functioning
Check No. 05
Check the four way valve.
Malfunctioning
Functioning
Check No. 11
Check the refrigerant line.
Functioning
Malfunctioning
Refrigerant shortage
Water mixed
Stop valve defective
(R4697)
90
Service Diagnosis
SiBE06-514
Troubleshooting
Remote
Controller
Display
Method of
Malfunction
Detection
A compressor lock is detected by checking the compressor running condition through the
position detection circuit.
Malfunction
Decision
Conditions
The system judges the compressor lock, and stops due to over current.
The system judges the compressor lock, and cannot operation with position detection within
15 seconds after start up.
The system will be shut down if the error occurs 16 times.
Clearing condition: Continuous run for about 10 minutes (normal)
Supposed
Causes
Compressor locked
Compressor harness disconnected
Troubleshooting
Caution
Normal?
NO
Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)
YES
Turn off the power and reconnect
the harnesses. Turn on the power
again and get the system restarted.
Emergency stop
without compressor
running?
YES
Replace the compressor.
NO
System shut
down after errors repeated
several times?
NO
YES
Replace the compressor.
(R2842)
Note:
Service Diagnosis
If the model doesnt have SPM, replace the outdoor unit PCB.
91
Troubleshooting
SiBE06-514
E7
Method of
Malfunction
Detection
A fan motor or related error is detected by checking the high-voltage fan motor rpm being
detected by the Hall IC.
Malfunction
Decision
Conditions
The fan does not start in 30 seconds even when the fan motor is running.
The system will be shut down if the error occurs 16 times.
Clearing condition: Continuous run for about 10 minutes (normal)
Supposed
Causes
Troubleshooting
Caution
Check No.15
Refer to P.119
YES
NO
Foreign matters in or
around the fan?
YES
Remove.
NO
Get started.
Check No. 15
Check the outdoor unit PCB rpm
pulse input.
NO
YES
Replace the outdoor unit
PCB.
(R2843)
92
Service Diagnosis
SiBE06-514
Troubleshooting
Remote
Controller
Display
Method of
Malfunction
Detection
An input over-current is detected by checking the input current value with the compressor
running.
Malfunction
Decision
Conditions
The following current with the compressor running continues for 2.5 seconds.
Cooling / Heating: Above 12A
Supposed
Causes
Troubleshooting
Caution
Check No.07
Refer to P.117
Check No.08
Refer to P.117
An input over-current may result from wrong internal wiring. If the wires have been disconnected and
reconnected for part replacement, for example, and the system is interrupted by an input over-current,
take the following procedure.
Get restarted and measure the
input current.
NO
YES
Turn off the power and disconnect
the harnesses U, V and W.
Inverter checker
Part No.: 1225477
YES
Any LED off?
NO
Turn off the power, and reconnect
the harnesses. Turn on the power
again and get restarted.
Check No. 08
Check the discharge pressure.
Check No. 07
Check the installation condition.
(R4698)
Note:
Service Diagnosis
If the model doesnt have SPM, replace the outdoor unit PCB.
93
Troubleshooting
SiBE06-514
EA
Method of
Malfunction
Detection
The indoor air temperature thermistor, the indoor unit heat exchanger thermistor, the outdoor
temperature thermistor and the outdoor unit heat exchanger thermistor are checked to see if
they function within their normal ranges in the operating mode.
Malfunction
Decision
Conditions
Supposed
Causes
94
Service Diagnosis
SiBE06-514
Troubleshooting
Troubleshooting
Caution
Check No.05
Refer to P.115
Check No.06
Refer to P.116
Check No.11
Refer to P.118
YES
Correct.
NO
YES
Reconnect.
NO
Check the continuity of the four
way valve coil and harness.
Disconnect the
harness from
the connector.
Resistance between
harnesses about
3k0.5k?
NO
YES
Check No. 05
Check the four way valve
switching output.
Malfunctioning
Functioning
Any thermistor disconnected?
YES
Reconnect in position.
NO
Check No. 06
Check the thermistors.
Malfunctioning
Replace a defective
thermistor.
Functioning
Check No. 11
Check the refrigerant line.
Functioning
Malfunctioning
Insufficient gas
Water mixed
Stop valve defective
Service Diagnosis
95
Troubleshooting
SiBE06-514
F3
Method of
Malfunction
Detection
The discharge pipe temperature control (stop, frequency drooping, etc.) is checked with the
temperature being detected by the discharge pipe thermistor.
Malfunction
Decision
Conditions
If a stop takes place 4 times successively due to abnormal discharge pipe temperature, the
system will be shut down.
If the temperature being detected by the discharge pipe thermistor rises above
C, the
compressor will stop. (The error is cleared when the temperature has dropped below
C.)
Stop temperatures
(1) above 45Hz (rising), above 40Hz (dropping)
(2) 30~45Hz (rising), 25~40Hz (dropping)
(3) below 30Hz (rising), below 25Hz (dropping)
110
105
99
97
92
86
The error counter will reset itself if this or any other error does not occur during the following
60-minute compressor running time (total time).
Supposed
Causes
Refrigerant shortage
Four way valve malfunctioning
Discharge pipe thermistor defective
(heat exchanger or outdoor air temperature thermistor defective)
Outdoor unit PCB defective
Water mixed in the local piping
Electronic expansion valve defective
Stop valve defective
Troubleshooting
Caution
Check No.04
Refer to P.114
Check No.06
Refer to P.116
Check No.11
Refer to P.118
Check No. 06
Check the thermistors.
Functioning
Check No. 04
Check the electronic expansion
valve.
Malfunctioning
Discharge pipe thermistor
Outdoor unit heat exchanger thermistor
Outdoor temperature thermistor
Malfunctioning
Replace a defective
thermistor.
Functioning
Check No. 11
Check the refrigerant line.
Functioning
Malfunctioning
Refrigerant shortage
Four way valve malfunctioning
Water mixed
Stop valve defective
(R4700)
96
Service Diagnosis
SiBE06-514
Troubleshooting
F6
Method of
Malfunction
Detection
High-pressure control (stop, frequency drop, etc.) is activated in the cooling mode if the
temperature being sensed by the heat exchanger thermistor exceeds the limit.
Malfunction
Decision
Conditions
Activated when the temperature being sensed by the heat exchanger thermistor rises above
65C. (The error is cleared when the temperature drops below 54C.)
Supposed
Causes
Service Diagnosis
97
Troubleshooting
SiBE06-514
Troubleshooting
Caution
Check No.04
Refer to P.114
Check No.06
Refer to P.116
Check No. 07
Installation condition
check
Abnormal
Normal
Check No.07
Refer to P.117
Check No. 09
Outdoor fan check
Abnormal
Normal
Check No.09
Refer to P.118
Check No. 04
Electronic expansion valve check
Judgment
Abnormal
Normal
Check No. 06
Heat exchanger thermistor check
Judgment
Abnormal
Normal
Replace PCB.
(R4701)
98
Service Diagnosis
SiBE06-514
Troubleshooting
HO
Method of
Malfunction
Detection
Malfunction
Decision
Conditions
If the DC current before compressor start-up is out of the range 0.5-4.5 V (sensor output
converted to voltage value) or if the DC voltage before compressor start-up is below 50 V.
Supposed
Causes
PCB defective
Broken or poorly connected harness
Troubleshooting
Caution
YES
NO
Turn off the power and turn it
on again.
NO
No problem. Keep on
running.
YES
Replace the PCB (2).
(R4564)
Service Diagnosis
99
Troubleshooting
SiBE06-514
H6
Method of
Malfunction
Detection
A compressor startup failure is detected by checking the compressor running condition through
the position detection circuit.
Malfunction
Decision
Conditions
The compressor fails to start in about 15 seconds after the compressor run command signal
is sent.
Clearing condition: Continuous run for about 10 minutes (normal)
The system will be shut down if the error occurs 16 times.
Supposed
Causes
Troubleshooting
Caution
Check No.13
Refer to P.119
Check No. 13
Check for short-circuit.
Normal
NO
YES
Check the electrolytic capacitor
voltage.
NO
DC290~380V?
YES
Electricals
or compressor harnesses
connected as
specified?
NO
Reconnect as specified.
YES
Turn off the power. Disconnect the
harnesses U, V and W.
Inverter checker
Part No.: 1225477
YES
Correct the power supply or
replace the outdoor unit
PCB.
Replace the compressor.
(R3041)
100
Service Diagnosis
SiBE06-514
Troubleshooting
H8
Method of
Malfunction
Detection
Detecting abnormality of the DC sensor by the running frequency of compressor and by the
input current multiplied DC voltage and current.
Malfunction
Decision
Conditions
Supposed
Causes
Troubleshooting
Caution
Service Diagnosis
101
Troubleshooting
SiBE06-514
Method of
Malfunction
Detection
This type of error is detected by checking the thermistor input voltage to the microcomputer.
[A thermistor error is detected by checking the temperature.]
Malfunction
Decision
Conditions
The thermistor input is above 4.96 V or below 0.04 V with the power on.
Error J3 is judged if the discharge pipe thermistor temperature is smaller than the condenser
thermistor temperature.
Supposed
Causes
102
Service Diagnosis
SiBE06-514
Troubleshooting
Check No.06
Refer to P.116
Troubleshooting
Caution
NO
Reconnect.
YES
Connector or thermistor
disconnected?
YES
Reconnect.
NO
Check No. 06
Check the thermistor resistance
value.
NO
Normal?
YES
Check No. 06
Check the indoor heat exchanger
thermistor resistance value in the
heating mode.
Indoor
heat exchanger thermistor
functioning?
NO
YES
Service Diagnosis
103
Troubleshooting
SiBE06-514
L3
Method of
Malfunction
Detection
An electrical box temperature rise is detected by checking the radiation fin thermistor with the
compressor off.
Malfunction
Decision
Conditions
With the compressor off, the radiation fin temperature is above 80C. Reset is made when the
temperature drops below 70C.
Supposed
Causes
104
Service Diagnosis
SiBE06-514
Troubleshooting
Troubleshooting
Caution
Check No.06
Refer to P.116
Check No.07
Refer to P.117
Error again or outdoor unit
fan activated?
Check No.09
Refer to P.118
WARNING
To cool down the electricals, the
outdoor unit fan gets started when
the radiation fin temperature rises
above 80C and stops itself when it
drops below 70C.
YES
NO
Check No. 06
Check the thermistor resistance
value.
Fin thermistor
Check the radiation fin
temperature.
Thermistor as
specified in its characteristic
chart?
NO
Replace the fin thermistor.
YES
Above 80C?
NO
Replace the outdoor unit
PCB.
YES
Check No. 09
Check the outdoor unit
fan or related.
Malfunctioning
Replace the fan motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.
Functioning
Too dirty
Clean up the radiation fin.
Slightly dirty
Check No. 07
Check the installation condition.
(R4703)
Service Diagnosis
105
Troubleshooting
SiBE06-514
L4
Method of
Malfunction
Detection
A radiation fin temperature rise is detected by checking the radiation fin thermistor with the
compressor on.
Malfunction
Decision
Conditions
Supposed
Causes
106
Service Diagnosis
SiBE06-514
Troubleshooting
Troubleshooting
Caution
Check No.06
Refer to P.116
Check No.07
Refer to P.117
Error displayed again?
Check No.09
Refer to P.118
YES
NO
Check No. 06
Check the thermistor resistance
value.
Fin thermistor
Check the radiation fin
temperature.
Thermistor as
specified in its characteristic
chart?
NO
Replace the fin thermistor.
YES
Above 90C?
YES
Check No. 09
Check the outdoor unit
fan or related.
Malfunctioning
Replace the fan motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.
Functioning
NO
Too dirty
Slightly dirty
Check No. 07
Check the installation condition.
(R4704)
Service Diagnosis
107
Troubleshooting
SiBE06-514
L5
Method of
Malfunction
Detection
An output over-current is detected by checking the current that flows in the inverter DC section.
Malfunction
Decision
Conditions
Supposed
Causes
108
Service Diagnosis
SiBE06-514
Troubleshooting
Troubleshooting
Caution
Check No.07
Refer to P.117
Check No.08
Refer to P.117
An output over-current may result from wrong internal wiring. If the wires have been disconnected and
reconnected for part replacement, for example, and the system is interrupted by an output over-current,
take the following procedure.
NO
YES
Check No.13
Refer to P.119
Error again?
YES
Possible causes
Instantaneous supply voltage
drop
Compressor motor overloaded
Contact-induced electrical
shortcircuit
Inverter checker
Part No.: 1225477
Keep on using as it is
(monitor).
Check the electricals'
connectors and other
fittings.
YES
Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)
NO
Check No. 13
Check the power transistor.
Normal?
NO
Replace the SPM.
(Replace the outdoor unit
PCB.)
YES
Turn off the power, and reconnect
the harnesses. Turn on the power
again and get restarted.
Voltage as rated?
NO
Correct the power supply.
YES
Short-circuit
or breakage between
compressor's coil
phases?
YES
Replace the compressor.
NO
Check No. 08
Check the discharge pressure.
Check No. 07
Check the installation condition.
(R4705)
Note:
Service Diagnosis
If the model doesnt have SPM, replace the outdoor unit PCB.
109
Troubleshooting
SiBE06-514
U0
Gas shortage detection I:
Gas shortage is detected by checking the input current value and the compressor running
frequency. If the gas is short, the input current is smaller than the normal value.
Gas shortage detection II:
Gas shortage is detected by checking the discharge temperature and the opening of the
electronic expansion valve. If the gas is short, the discharge temperature tends to rise.
Gas shortage detection III:
A gas shortage is detected by checking the difference between inhale and exhale temperature.
Malfunction
Decision
Conditions
Cooling
Heating
4.0C
4.0C
3.0C
3.0C
If a gas shortage error takes place 4 times straight, the system will be shut down. The error
counter will reset itself if this or any other error does not occur during the following 60-minute
compressor running time (total time).
Supposed
Causes
110
Service Diagnosis
SiBE06-514
Troubleshooting
Troubleshooting
Caution
Check No.04
Refer to P.114
Check No.06
Refer to P.116
Any thermistor
disconnected?
NO
Stop valve closed?
YES
Reconnect in position.
* Discharge pipe thermistor
* Indoor / outdoor unit heat exchanger thermistor
* Room temperature thermistor
* Outdoor air thermistor
YES
Open the stop valve.
NO
Check for gas leakage.
YES
Repair the pipe flare or
replace the square union.
NO
Oil oozing at internal piping?
YES
NO
Check No. 04
Electronic expansion valve
functioning?
Compressor vibrating
too much?
NO
NO
YES
YES
Gas shortage error again?
Replace the room
NO
Check No. 06
Check the thermistors.
Functioning
Service Diagnosis
111
Troubleshooting
SiBE06-514
Remote
Controller
Display
Method of
Malfunction
Detection
An abnormal voltage rise is detected by checking the specified over-voltage detection circuit.
Malfunction
Decision
Conditions
An over-voltage signal is fed from the over-voltage detection circuit to the microcomputer
(The voltage is over 400V).
The system will be shut down if the error occurs 255 times.
Clearing condition: Continuous run for about 10 minutes (normal)
Supposed
Causes
Troubleshooting
Caution
Supply voltage as
specified?
NO
Correct the power supply.
YES
Turn on the
power again.
Error displayed again?
NO
Disturbance factors
Noise Power supply distortion
YES
Repeat a
couple of times.
Note:
112
If the model doesnt have SPM, replace the outdoor unit PCB.
Service Diagnosis
SiBE06-514
Check
5. Check
5.1
How to Check
1.
2.
3.
4.
5.
(R1224)
Check No.02
5
4
3
2
1
(R1073)
Remove the front grille. The limit switch is located at the left side of the drain pan assembly.
Check the continuity of the switch connection.
Shutter status
Open
Closed
Continuity
Continuity
No continuity
Upward
Tester
Limit switch
Forward
Service Diagnosis
(Q0363)
The shutter can be opened and closed with hand. Keep the shutter open and closed all the
way for each continuity check steps.
113
Check
SiBE06-514
Check
6P Connector
1
5-2
5-4
6-1
6-3
6
(R1082)
4. If no EV generates latching sound in the above step 2, the outdoor unit PCB is faulty.
5. If the conductivity is confirmed in the above step 2, mount a good coil (which generated
latching sound) in the EV unit that did not generate latching sound, and check to see if that
EV generates latching sound.
If latching sound is generated, the outdoor unit PCB is faulty.
If latching sound is not generated, the EV unit is faulty.
Note:
114
Please note that the latching sound varies depending on the valve type.
Service Diagnosis
SiBE06-514
Check
S80 voltage
at DC 180-220 V with
compressor on?
(Fig. 1)
NO
YES
Disconnect the four way valve coil
from the connector and check the
continuity.
NO
YES
Replace the four way valve.
(Fig. 1)
Voltage at S80
DC180-220V
Compressor
Time
ON
Service Diagnosis
(R3047)
115
Check
SiBE06-514
Remove the connectors of the thermistors on the PCB, and measure the resistance of each
thermistor using tester.
The relationship between normal temperature and resistance is shown in the graph and the
table below.
Thermistor R25C=20k B=3950
Temperature (C)
20
15
10
5
0
5
10
15
20
25
30
35
40
45
50
211.0 (k)
150
116.5
88
67.2
51.9
40
31.8
25
20
16
13
10.6
8.7
7.2
Tester
Resistance range
100
50
-15
116
15
30
45
(C)
(R1437)
Service Diagnosis
SiBE06-514
Check
Check
the allowable
dimensions of the air suction
and discharge
area.
Normal
Does
the discharged
air from other outdoor
unit cause an increase of
the suction air
temperature?
Abnormal
YES
NO
Is the heat exchanger
very dirty?
NO
Is
the air flow
blocked by obstacles or
winds blowing in the
opposite direction?
YES
YES
NO
High
NO
Replace compessor.
YES
Is the stop valve open?
NO
Open the stop valve.
YES
Is the
connection pipe deformed?
NO
Replace the pipe installed at
the site.
YES
At the heat exchanger and
air filter dirty?
YES
NO
Clean.
Replace the compressor.
(R1443)
Service Diagnosis
117
Check
SiBE06-514
DC motor
Check the outdoor unit fan system.
NO
YES
Reconnect.
NO
Measure the power supply waveform between pins 1 and 3 on the terminal board, and check
the waveform disturbance.
Check to see if the power supply waveform is a sine wave (Fig.1).
Check to see if there is waveform disturbance near the zero cross (sections circled in Fig.2)
[Fig.1]
[Fig.2]
Is
the discharge
thermister disconnected from
the holder?
YES
NO
Is any moisture
found in sight glass.
NO
YES
118
Service Diagnosis
SiBE06-514
Check
Check to make sure that the voltage between the terminal of Power transistor (+) and (-) is
approx. 0 volt before checking power transistor.
< Measuring method >
Disconnect the compressor harness connector from the outdoor unit PCB. To disengage the
connector, press the protrusion on the connector.
Then, follow the procedure below to measure resistance between power transistor (+) and (-)
and the U, V and W terminals of the compressor connector with a multi-tester. Evaluate the
measurement results for a pass/fail judgment.
<Power transistor check>
Negative (-) terminal of
Power transistor
tester (positive terminal
(+)
(+) for digital tester)
Positive (+) terminal of
UVW
tester (negative terminal
(-) for digital tester)
Normal resistance
Unacceptable resistance
UVW
Power transistor
(-)
UVW
Power transistor
(+)
UVW
Power transistor
(-)
Several k to several M ()
Short (0 ) or open
5.1.12 Turning Speed Pulse Input on the Outdoor Unit PCB Check
Check No.15
DC270V
(R2859)
Service Diagnosis
119
Check
120
SiBE06-514
Service Diagnosis
SiBE06-514
Part 7
Removal Procedure
1. Indoor Unit...........................................................................................122
1.1
1.2
1.3
1.4
1.5
1.6
2. Outdoor Unit........................................................................................135
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Removal Procedure
121
Indoor Unit
SiBE06-514
1. Indoor Unit
1.1
Procedure
Warning
Step
1 Appearance
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Points
Operation panel
Enlarged illustration
shows operation
panel section.
Front panel
(Suction port)
When push
the knob,
the lock plate
draws in.
When push
it again,
the plate
comes out. (R2605)
Push lock
AIR OUTLET
SELECTION
(R2606)
122
Removal Procedure
SiBE06-514
Step
3 Press down the two
Indoor Unit
Procedure
Points
FRONT
(R2607)
Chain
(R2608)
Removal Procedure
123
Indoor Unit
Step
5 Undo the three hooks
SiBE06-514
Procedure
Points
Hooks
(three locations)
(R2609)
Hooks
<Main unit side>
(R2611)
Mounting screw M4 16
124
Removal Procedure
SiBE06-514
1.2
Indoor Unit
Procedure
Step
1 Open the horizontal
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work
Procedure
Points
blade.
Removal Procedure
125
Indoor Unit
1.3
SiBE06-514
Procedure
Step
1 Set the horizontal
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work
Procedure
Points
blade in horizontal
position to take out the
front grille toward
yourself.
126
(R2618)
Removal Procedure
SiBE06-514
Indoor Unit
Step
4 Remove the room
Procedure
Points
temperature thermistor.
Room
temperature
thermistor
(R2619)
Thermistor
retaining
spring
Heat
exchanger
thermistor
(R2621)
Heat
exchanger
thermistor
Mounting screw M4 8
(R2622)
Removal Procedure
127
Indoor Unit
Step
7 To remove the
SiBE06-514
Procedure
Points
Mounting screw M4 16
Green Yellow
SW1
ON/OFF switch
Red
SW1
Signal
receiving
plate
LED A Green
A
B
LED B Green
(R2624)
128
Removal Procedure
SiBE06-514
1.4
Indoor Unit
Procedure
Warning
Step
1 Loosen the fixing screw
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work
Procedure
Points
Service
PCB
Display PCB
Control PCB
Home Leave
Operation lamp
(R2625)
LED11
LED12
LED14
Green
Yellow
Red
Main unit
ON/OFF
switch
SW1
S6
S23
S25
S302
S301
S21
S201
S203
Removal Procedure
S32
S31
S7
(R2627)
129
Indoor Unit
Step
3 The figure shows the
SiBE06-514
Procedure
Points
S204
S8
SW2
SW2
SW2-1 : unused
SW2-2 : unused
SW2-3 : unused
SW2-4 :
OFF - initial set
ON - limit upward air flow
(R2628)
Discharge
change-over
(R2630)
Discharge
change-over
switch
S26
(R2629)
130
Select
to discharge air
only from top discharge port.
Select
to discharge air
with automatic pattern
decided in accordance with
operation mode and
operation conditions.
It is recommendable to
select
.
Removal Procedure
SiBE06-514
1.5
Procedure
Step
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work
Procedure
Conduct pump-down
operation and check that
gas has been purged
completely before starting
service work.
1 Loosen the two screws
to remove the top
discharge grille.
Indoor Unit
Points
Mounting screw M4 16
Warning
If refrigerant gas leaks during
service work, ventilate work
area.
(Toxic gas may be generated
when refrigerant gas contacts
with flame.)
14/17 double ended wrench
Caution
Do not contaminate any gas
(including air) other than the
specified refrigerant (R410A)
(Contaminating of air or other
gas causes abnormal
temperature rise in
refrigerating cycle, and this
results in pipe breakage or
personal injuries.)
After pipes are
disconnected, close all pipe
openings with caps to
prevent dust and moisture
from entering pipes.
Removal Procedure
131
Indoor Unit
Step
5 Loosen the fixing screw
SiBE06-514
Procedure
Points
Mounting screw M4 16
Pipe
retaining
plate
(R2634)
Mounting screw M4 16
Hooks
(R2635)
Caution
When removing or reinstalling heat exchanger, be
sure to wear protective gloves
or wrap heat exchanger with
cloths. (Fins can cut fingers.)
Hook
(R2636)
132
Removal Procedure
SiBE06-514
1.6
Indoor Unit
Procedure
Step
1 For removal of the
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work
Procedure
Points
Distributing louver
Removal Procedure
(R2639)
133
Indoor Unit
Step
4 Loosen the six screws
SiBE06-514
Procedure
Points
134
Condition : Casing
Protruded : Not to be removed
Semi-sink : To be removed
Sink : Not to be removed
Removal Procedure
SiBE06-514
Outdoor Unit
2. Outdoor Unit
2.1
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
1. Features
Handle
(R3235)
Outdoor air
thermistor
(R3236)
(R3237)
Shelter
(R3238)
Removal Procedure
135
Outdoor Unit
SiBE06-514
Procedure
Step
Points
Top panel
(R3239)
(R3240)
Disconnect the
connector for fan motor
(S70).
S70
Front panel
136
(R3241)
(R3242)
Removal Procedure
SiBE06-514
Outdoor Unit
Procedure
Step
Points
Hooks
(R3243)
Propeller fan
(R3244)
Align
mark of the
propeller fan with D-cut
section of the motor shaft
when reassembling.
D-cut
(R3245)
Removal Procedure
137
Outdoor Unit
Procedure
Step
SiBE06-514
Points
Bell mouth
Hooks
(R3246)
Lead wire
Propeller fan
(R3249)
138
Removal Procedure
SiBE06-514
Procedure
Step
Outdoor Unit
Points
M416
DC fan motor
Fan motor
(R3250)
(R3251)
Removal Procedure
139
Outdoor Unit
SiBE06-514
Procedure
Step
Points
(R3254)
140
Removal Procedure
SiBE06-514
Step
Outdoor Unit
Procedure
Points
Hook
(R3257)
Removal Procedure
141
Outdoor Unit
2.2
SiBE06-514
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
Disconnect the
connector for four way
valve (S80).
(R3260)
142
Removal Procedure
SiBE06-514
Procedure
Step
Outdoor Unit
Points
Thermistor
Piping
Clip
(R3262)
(R3261)
Clip
(R3263)
(R3264)
Removal Procedure
143
Outdoor Unit
2.3
SiBE06-514
Procedure
Step
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Points
Reactor
(R3266)
Partition plate
(R3268)
144
Removal Procedure
SiBE06-514
Outdoor Unit
Procedure
Step
Points
(R3270)
Removal Procedure
145
Outdoor Unit
2.4
SiBE06-514
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
Sound blanket
(R3271)
146
Removal Procedure
SiBE06-514
Outdoor Unit
Procedure
Step
Removal Procedure
Points
147
Outdoor Unit
2.5
SiBE06-514
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
Terminal
cover
(R3276)
Red (U)
Yellow (V)
Blue (W)
(R3277)
148
Removal Procedure
SiBE06-514
Procedure
Step
Outdoor Unit
Points
Tube cutter
(R3280)
Removal Procedure
149
Outdoor Unit
2.6
Removal of Compressor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Before working,
make sure that the
refrigerant is empty
in the circuit.
Be sure to apply
nitrogen
replacement when
heating up the
brazed part.
SiBE06-514
Points
Warning
Ventilate when refrigerant
leaks during the work.
(If refrigerant contacts fire, it
will cause to arise toxic gas.)
Provide a protective sheet or
a steel plate so that the
brazing flame cannot
influence peripheries.
Be careful so as not to burn
the compressor terminals or
the name plate.
Be careful so as not to burn
the heat exchanger fin.
Warning
Since it may happen that
refrigeration oil in the
compressor will catch fire,
prepare wet cloth so as to
extinguish fire immediately.
In case of the difficulty with
gas brazing machine
1. Disconnect the brazed part
where is easy to disconnect
and restore.
2. Cut pipes on the main unit by
a miniature copper tube
cutter in order to make it
easy to disconnect.
Cautions for restoration
1. Restore the piping by nonoxidation brazing.
2. It is required to prevent the
carbonization of the oil inside
the four way valve and the
deterioration of the gaskets
affected by heat. For the
sake of this, wrap the four
way valve with wet cloth and
provide water so that the
cloth will not be dried and
avoid excessive heating.
(Keep below 120C)
Note: Do not use a metal
saw for cutting pipes by all
means because the sawdust
come into the circuit.
150
Removal Procedure
SiBE06-514
Outdoor Unit
Procedure
Step
Removal Procedure
Points
151
Outdoor Unit
2.7
Removal of PCB
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
152
SiBE06-514
Points
Removal Procedure
SiBE06-514
Outdoor Unit
Procedure
Step
Points
Hooks
(R3290)
Removal Procedure
153
Outdoor Unit
Procedure
Step
SiBE06-514
Points
S90
Glass fuse
3.15A
S70
Glass fuse
S80
LED A
V3
Varistor
(R4591)
154
Removal Procedure
SiBE06-514
Part 8
Others
1. Others .................................................................................................156
1.1 Test Run from the Remote Controller ..................................................156
1.2 Jumper Settings ...................................................................................157
Others
155
Others
SiBE04-507
1. Others
1.1
In cooling mode, select the lowest programmable temperature; in heating mode, select the
highest programmable temperature.
Trial operation may be disabled in either mode depending on the room temperature.
After trial operation is complete, set the temperature to a normal level.
(26C to 28C in cooling mode, 20C to 24C in heating mode)
For protection, the system disables restart operation for 3 minutes after it is turned off.
(3)
(2)
ON/OFF
TEMP
(3)
156
MODE
(1) (4)
(R4294)
Others
SiBE04-507
1.2
Others
Jumper Settings
ADDRESS
1
CUT
J4
JB
Infrared
remote
control
ADDRESS: JA
EXIST
1
CUT
2
J4
EXIST
Electrical
equipment box
R92
R91
R90
ADDRESS
JA
3) Screw
Electrical
equipment box lid
JC
2) Connector 7P
2) Connector 5P
6) JA
(R4676)
ADDRESS: JA
Electrical
equipment box
EXIST
CUT
3) Screw
2) Connector 9P
4) Screw
Hole
PCB
(R4675)
JB
Others
When connected
(factory set)
Auto-restart
When cut
157
Others
158
SiBE04-507
Others
SiBE06-514
Part 9
Appendix
1. Piping Diagrams..................................................................................160
1.1 Indoor Units ..........................................................................................160
1.2 Outdoor Units .......................................................................................161
2. Wiring Diagrams..................................................................................163
2.1 Indoor Units ..........................................................................................163
2.2 Outdoor Units .......................................................................................163
Appendix
159
Piping Diagrams
SiBE04-507
1. Piping Diagrams
1.1
Indoor Units
FVKS25/35BVMB, FVXS25/35BVMB
INDOOR UNIT
HEAT EXCHANGER
7.9CuT
M
CROSS FLOW FAN
FAN MOTOR
M
CROSS FLOW FAN
FAN MOTOR
THERMISTOR
ON HEAT EXCH.
7.0CuT
7.0CuT
FIELD PIPING
(6.4CuT)
9.5CuT
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
HEATING
4D034714B
160
Appendix
SiBE04-507
1.2
Piping Diagrams
Outdoor Units
9.5CuT
7.0CuT
6.4CuT 6.4CuT
MUFFLER
WITH
FILTER
MOTOR OPERATED
VALVE
MUFFLER
WITH
FILTER
9.5CuT
PROPELLER FAN
. 4.0ID. 2.0CuT
HEAT EXCHANGER
THERMISTOR
9.5CuT
FOUR WAY
VALVE
NORMALLY : OFF
9.5CuT
7.9CuT
6.4CuT
MUFFLER
WITH
FILTER
LIQUID STOP
VALVE
MUFFLER
FIELD PIPING
(6.4CuT)
7.9CuT
DISCHARGE PIPE
THERMISTOR
9.5CuT
9.5CuT
COMPRESSOR
GAS STOP
VALVE
MUFFLER
ACCUMULATOR
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
3D047317
RKS35DVMB, RKS35D2VMB
OUTDOOR UNIT
OUTDOOR TEMPERATURE
THERMISTOR
9.5CuT
4.8CuT MUFFLER
WITH
FILTER
MUFFLER
WITH
FILTER
PROPELLER FAN
9.5CuT
MOTOR OPERATED
VALVE
. 4.0ID. 2.0CuT
HEAT EXCHANGER
THERMISTOR
4.8CuT
6.4CuT 6.4CuT
9.5CuT
FOUR WAY
VALVE
NORMALLY : OFF
9.5CuT
7.9CuT
6.4CuT
MUFFLER
WITH
FILTER
LIQUID STOP
VALVE
7.9CuT
MUFFLER
DISCHARGE PIPE
THERMISTOR
9.5CuT
COMPRESSOR
ACCUMULATOR
9.5CuT
MUFFLER
GAS STOP
VALVE
FIELD PIPING
(6.4CuT)
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
3D047318
Appendix
161
Piping Diagrams
SiBE04-507
9.5CuT
7.0CuT
6.4CuT 6.4CuT
MUFFLER
WITH
FILTER
MOTOR OPERATED
VALVE
MUFFLER
WITH
FILTER
9.5CuT
PROPELLER FAN
. 4.0ID. 2.0CuT
HEAT EXCHANGER
THERMISTOR
9.5CuT
7.9CuT
FOUR WAY
VALVE
ON : HEATING
9.5CuT
6.4CuT
MUFFLER
WITH
FILTER
LIQUID STOP
VALVE
7.9CuT
MUFFLER
DISCHARGE PIPE
THERMISTOR
9.5CuT
9.5CuT
COMPRESSOR
GAS STOP
VALVE
MUFFLER
ACCUMULATOR
FIELD PIPING
(6.4CuT)
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
HEATING
3D047315
RXS35DVMB, RXS35D2VMB
OUTDOOR UNIT
OUTDOOR TEMPERATURE
THERMISTOR
9.5CuT
4.8CuT MUFFLER
WITH
FILTER
MUFFLER
WITH
FILTER
PROPELLER FAN
9.5CuT
MOTOR OPERATED
VALVE
9.5CuT
. 4.0ID. 2.0CuT
HEAT EXCHANGER
THERMISTOR
4.8CuT
6.4CuT 6.4CuT
FOUR WAY
VALVE
ON : HEATING
9.5CuT
7.9CuT
6.4CuT
MUFFLER
WITH
FILTER
LIQUID STOP
VALVE
MUFFLER
FIELD PIPING
(6.4CuT)
7.9CuT
DISCHARGE PIPE
THERMISTOR
9.5CuT
COMPRESSOR
ACCUMULATOR
9.5CuT
MUFFLER
GAS STOP
VALVE
FIELD PIPING
(9.5CuT)
REFRIGERANT FLOW
COOLING
HEATING
3D047316
162
Appendix
SiBE04-507
Wiring Diagrams
2. Wiring Diagrams
2.1
Indoor Units
FVKS25/35BVMB, FVXS25/35BVMB
PCB3
S26
S2W(4)
S4W
INFRARED
REMOTE
CONTROL
S25
3.15A
H1
FU
H2
H3
TRANSMISSION
CIRCUIT
PCB2
S23
S1W
S6
M1S
S21
HA
S8
S201
S202
S203
S204
S301
S43
S302
S31
L1S
PCB1
S7
M
S41
M2S
1
2
3
X1M
1
2
3
outdoor
FIELD WIRING.
PCB4
S24
BLK
WHT
RED
GRN/
YLW
FG
M1F
(UPPER FAN MOTOR)
M2F
(LOWER FAN MOTOR)
S44
S32
: PROTECTIVE EARTH
FU
: FUSE
H1P, H2P, H3P : PILOT LAMP
L1S
: LIMIT SWITCH
M1F, M2F
: FAN MOTOR
M1S
: SWING MOTOR
M2S
: LOWER AIR OUTLET MOTOR
PCB1~PCB4 : PRINTED CIRCUIT BOARD
R1T, R2T
: THERMISTOR
S6~S302
: CONNECTOR
S1W
: OPERATION SWITCH
S2W(4)
: UPWARD AIR FLOW LIMIT SWITCH
S4W
: AIR OUTLET SELECTION SWITCH
X1M
: TERMINAL STRIP
S42
R1T
indoor
R2T
3D034713B
2.2
Outdoor Units
RK(X)S25/35DVMB, RK(X)S25/35D2VMB
R12T
t
BRN
BRN
C100
MRM10
V3
V3
7
DB2
DB2
~ +
~+
~ -
~ -
HL3
HL3
WHT
WHT
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
~ -
FU1
1
S10
S10
IC11
FU1
3.15A
3.15A V1
V1
S20 6
1 S20 6
PCB2
PCB2
MRCW
1
S80
~ -
IC11
MRCW
33
S90
11 S90 66
IPM1
HC4
IPM1
HC4
C74 +
C74 - +
C75 +
C75 - -
outdoor
outdoor
11
33
IN
OF
IN CASE
CASE OF
COOLING
ONLY
COOLING ONLY
TYPE
TYPE
: CAPACITOR
: NEUTRAL
M
M
Y1E
Y1E
Y1R
Y1R
tt tt tt
+ C95
- C95
S70
S70
1 1 22 3 344 77
-WWV V UU
S40 S30
S40
S30
22
11
5 3 1
5 3 1
Z1C
V V Z1C
N=2
N=2
M
1~
1~
IN
OF
INCASE
CASE OF
R1TR2T
R2TR3T
R3T
R1T
HEAT
PUMP (OUTDOOR
HEAT PUMP
)
(DISCHARGE)
(OUTDOOR) (DISCHARGE)
TYPE
TYPE
(CONDENSER)
N
: NEUTRAL
PCB1, PCB2 ,
: PRINTED CIRCUIT BOARD SA1
PCB1 PCB2
: PRINTED CIRCUIT BOARD
Q1L Q1L
: OVERLOAD
PROTECTOR V1, V2, V3
: OVERLOAD PROTECTOR
, R3T
X1M
R1T, R2T
: THERMISTOR
R1T, R2T, R3T, R12T : THERMISTOR
, S20
Y1E
S10, S11S10
, S11, S20
, S70
S30, S40S30
Y1R
, S40, S70
, S91
S80, S90S80
Z1C, Z2C
, S90, S91
, HL3
, HN3
HC3, HC4
: CONNECTOR
, HC4
, HL3
, HN3 : CONNECTOR
HC3
C94
+
C94
+
FU2
- FU2
3.15A
3.15A
S80
S80
S80
: CAPACITOR
: DIODE BRIDGE
: DIODE BRIDGE
: FUSE
: FUSE
IC11
:
TRIAC
IC11
: TRIAC
IPM1
: INTELLIGENT POWER MODULE
IPM1
: INTELLIGENT POWER MODULE
L
: LIVE
L
: LIVE
L1
COIL
L1
: :COIL
L1R
REACTOR
L1R
: :REACTOR
M1C
:
COMPRESSOR MOTOR
MOTOR
M1C
: COMPRESSOR
M1F
FANMOTOR
MOTOR
M1F
: :FAN
MRCW,, MRM10
MRM10, ,MRM20
MRM20: :MAGNETIC
MAGNETIC RELAY
RELAY
MRCW
HN3
HN3
BLU
NOTE
NOTE
1. REFER TO THE NAMEPLATE FOR THE POWER REQUIREMENTS.
1.REFER TO THE NAMEPLATE FOR THE POWER REQUIREMENTS.
C74, C75
C74, C75
C94, C95, C100
C94, C95, C100
DB1, DB2
DB1, DB2
, FU2, FU3
FU1
FU1, FU2, FU3
HN2 GRY
S11
S11
SA1
HL2 ORG
HL2 GRY
HN2 BLU
SA1
HR1
HC3
HC3
HR2 DB1
~ +
HR2 DB1
~+
ORG
RED
MRM10
HN1 V2
S
V2
S
ORG
ORG
GRY
L1
HN1
L1R
BLU
BLU
YLW
YLW
RED
HR1
WHT
WHT
ORG
ORG
BRN
BRN
BLU
BLU
RED
RED
BLK
WHT
RED
RED
WHT
GRN/YLW
HL1 20A
GRN/YLW
GRN/YLW
L
L
N
BLK
L1R
MRM20
GRN/YLW
1
1
2
2
33
X1M
L 1
L 1
N 2
N 2
3
3
MRM20
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
X1M
YLW
HC1
HC2 HC1
FU3
Z2C HL1 20A
FU3 PCB1
L1
Z2C
BLK
BLK
GRY
HC2
PCB1
YLW
WHT
ORG
YLW
RED
ORG
YLW
BLU
BLK
BRN
GRY
RED
WHT
BLK
BLK
C100
M1F
M1F
Q1L
Q1L
(CONDENSER)
WW
UU
M1C
M1C
SA1
: SURGE ARRESTER
: SURGE ARRESTER
V1, V2, V3 : VARISTOR
:
VARISTOR
X1M
: TERMINAL STRIP
: TERMINAL
STRIP
Y1E
: ELECTRONIC EXPANSION VALVE COIL
EXPANSION
VALVE COIL
Y1R: ELECTRONIC
: REVERSING
SOLENOIDE
VALVE COIL
:
REVERSING
SOLENOIDE
Z1C, Z2C : FERRITE
COREVALVE COIL
: FERRITE
CORE
: PROTECTIVE EARTH
: PROTECTIVE EARTH
3D042576C
3D046707B
Appendix
163
Wiring Diagrams
164
SiBE04-507
Appendix
SiBE06-514
Index
Numerics
00 ...........................................................................79
3-minute standby ....................................................33
A
A1 ...........................................................................80
A5 ...........................................................................81
A6 ...........................................................................83
adjusting the air flow direction ................................57
air filter .................................................................122
air flow control ........................................................18
air flow selection .....................................................17
air purifying filter .....................................................25
ARC433A ...............................................................76
AUTO DRY COOL HEAT FAN operation .......55
automatic operation ................................................20
auto-restart ...........................................................157
auto-restart function ...............................................26
auto-swing ..............................................................16
B
bell mouth .............................................................138
C
C4 ...........................................................................85
C7 ...........................................................................86
C9 ...........................................................................85
care and cleaning ...................................................65
check
discharge pressure check ..............................117
electronic expansion valve check ..................114
fan motor connector output check .................113
four way valve performance check ................115
installation condition check ............................117
inverter units refrigerant system check ..........118
limit switch continuity check ...........................113
outdoor unit fan system check .......................118
power supply waveforms check .....................118
power transistor check ...................................119
thermistor resistance check ...........................116
turning speed pulse input on the outdoor unit PCB
check ...............................................119
check No.01 .........................................................113
check No.02 .........................................................113
check No.03 .........................................................113
check No.04 .........................................................114
check No.05 .........................................................115
check No.06 .........................................................116
check No.07 .........................................................117
check No.08 .........................................................117
check No.09 .........................................................118
check No.10 .........................................................118
check No.11 .........................................................118
check No.13 .........................................................119
check No.15 .........................................................119
Index
D
DC fan lock ............................................................ 92
DC voltage / current sensor abnormality ............. 101
defrost control ....................................................... 37
diagnosis mode ..................................................... 77
discharge pipe ....................................................... 39
discharge pipe control ........................................... 33
discharge pipe temperature control ................. 40, 96
discharge pipe thermistor .......... 27, 28, 39, 103, 143
discharge pressure check ................................... 117
display PCB ..................................................... 9, 129
drip proof plate .................................................... 136
E
E1 .......................................................................... 89
E5 .......................................................................... 90
E6 .......................................................................... 91
E7 .......................................................................... 92
E8 .......................................................................... 93
EA ......................................................................... 94
electrical box ............................................... 126, 142
electrical box temperature rise ............................ 104
electronic expansion valve check ........................ 114
electronic expansion valve control ........................ 38
error codes
00 .................................................................... 79
A1 ................................................................... 80
A5 ................................................................... 81
A6 ................................................................... 83
C4 ................................................................... 85
C7 ................................................................... 86
C9 ................................................................... 85
E1 ................................................................... 89
E5 ................................................................... 90
E6 ................................................................... 91
E7 ................................................................... 92
E8 ................................................................... 93
EA ................................................................... 94
F3 .................................................................... 96
F6 .................................................................... 97
H0 ................................................................... 99
H6 ................................................................. 100
H8 ................................................................. 101
H9 ................................................................. 102
J3 .................................................................. 102
J6 .................................................................. 102
i
SiBE06-514
L3 ...................................................................104
L4 ...................................................................106
L5 ...................................................................108
P4 ..................................................................102
U0 ..................................................................110
U2 ..................................................................112
U4 ....................................................................87
UA ....................................................................88
error codes and description ....................................79
F
F3 ...........................................................................96
F6 ...........................................................................97
facility setting jumper ........................................10, 43
fan control ..............................................................36
fan motor ..............................................133, 135, 139
fan motor (DC motor) or related abnormality .........83
fan motor connector output check ........................113
fan motor fixing frame ..........................................139
fan motor, connector ............................................136
fan rotor ................................................................133
fan speed control ....................................................18
fan speed setting ..................................................157
filter PCB ................................................................11
flap control ..............................................................16
forced operation mode ...........................................42
four way valve ......................................................148
four way valve abnormality .....................................94
four way valve operation compensation .................32
four way valve performance check .......................115
four way valve switching ........................................32
four way valve, connector ....................................142
freeze-up protection control .............................35, 81
frequency control ..............................................14, 30
frequency principle .................................................14
front panel ....................................................122, 136
FU ............................................................................8
FU1 ........................................................................10
FU2 ........................................................................10
FU3 ........................................................................10
function of thermistor ..............................................27
functions ...................................................................2
fuse ........................................................................10
I
indoor heat exchanger thermistor ................... 27, 28
indoor unit PCB abnormality ................................. 80
input current control .............................................. 34
input over current detection ................................... 93
installation condition check ................................. 117
instruction .............................................................. 47
insufficient gas .................................................... 110
insufficient gas control ........................................... 41
inverter features .................................................... 15
inverter POWERFUL operation ............................. 24
inverter principle .................................................... 14
inverter units refrigerant system check ................ 118
J
J3 ........................................................................ 102
J4 ........................................................................ 157
J6 ........................................................................ 102
J8 .......................................................................... 10
JB ........................................................................ 157
JC ........................................................................ 157
jumper settings .................................................... 157
L
L3 ........................................................................ 104
L4 ........................................................................ 106
L5 ........................................................................ 108
LED A .................................................................... 10
LED11 ..................................................................... 8
LED12 ..................................................................... 8
LED14 ..................................................................... 8
limit switch continuity check ................................ 113
liquid compression protection function 2 ............... 36
louvres ................................................................... 16
M
mode hierarchy ..................................................... 29
mold proof air filter ................................................ 25
N
names of parts ...................................................... 49
night set mode ....................................................... 22
H
H0 ...........................................................................99
H6 .........................................................................100
H8 .........................................................................101
H9 .........................................................................102
Hall IC ....................................................................18
HC3 ........................................................................10
HC4 ........................................................................10
heat exchanger ....................................................131
heat exchanger thermistor .....................85, 127, 143
heating peak-cut control .........................................35
high pressure control ..............................................81
high pressure control in cooling .............................97
HL3 .........................................................................10
HN3 ........................................................................10
HOME LEAVE operation ..................................23, 61
horizontal blade ....................................................125
ii
O
OL activation ......................................................... 90
ON/OFF button on indoor unit ............................... 25
opening limit .......................................................... 39
operation lamp ...................................................... 74
outdoor air temperature thermistor ...................... 103
outdoor heat exchanger thermistor ......... 27, 28, 103
outdoor unit fan system check ............................ 118
outdoor unit PCB abnormality ............................... 89
OUTDOOR UNIT SILENT operation ..................... 60
output over current detection .............................. 108
over current ............................................. 41, 93, 108
overload .......................................................... 41, 90
overload protector ................................................. 10
over-voltage detection ......................................... 112
Index
SiBE06-514
P
P4 .........................................................................102
panels ...................................................................135
partition plate ........................................................144
PCB ..............................................................129, 152
photocatalytic deodorizing filter ..............................25
PI control ................................................................31
piping diagrams ....................................................160
position sensor abnormality .................................100
power failure recovery function ............................157
power supply PCB ............................................8, 130
power supply waveforms check ...........................118
power transistor check .........................................119
POWERFUL operation .....................................24, 59
POWERFUL operation mode .................................42
preheating operation ..............................................32
preparation before operation ..................................52
pressure equalization control .................................39
printed circuit board (PCB)
control PCB ...................................................129
control PCB (indoor unit) ...................................9
control PCB (outdoor unit) ...............................11
display PCB ...............................................9, 129
filter PCB .........................................................11
power supply PCB .....................................8, 130
service PCB ...................................................130
signal receiver PCB ...........................................9
printed circuit board connector wiring diagram ........8
problem symptoms and measures .........................75
programme dry function .........................................19
propeller fan .........................................................137
R
radiation fin temperature rise ...............................106
radiation fin thermistor ..........................................103
reactor ..................................................................144
reactor harnesses ................................................142
remote controller ....................................................76
room temperature thermistor ..................................85
S
S10 .........................................................................10
S11 .........................................................................10
S20 .........................................................................10
S201 .........................................................................8
S202 .........................................................................8
S203 .........................................................................8
S204 .........................................................................8
S23 ...........................................................................8
S24 ...........................................................................8
S25 ...........................................................................8
S26 ...........................................................................8
S30 .........................................................................10
S301 .........................................................................8
S302 .........................................................................8
S31 ...........................................................................8
S32 ...........................................................................8
S40 .........................................................................10
S6 .............................................................................8
S7 .............................................................................8
S70 .........................................................10, 136, 154
Index
S8 ............................................................................ 8
S80 ........................................................ 10, 142, 154
S90 ................................................................ 10, 154
safety precautions ................................................. 47
self-diagnosis digital display .................................. 26
sensor malfunction detection ................................ 41
service check function ........................................... 76
service PCB ........................................................ 130
shelter ................................................................. 135
shutter drive motor ................................................ 86
shutter limit switch ................................................. 86
signal receiver PCB ................................................. 9
signal receiving sign .............................................. 25
signal transmission error ....................................... 87
sound blanket ...................................................... 146
specifications ........................................................... 4
starting operation control ....................................... 39
stop valve cover .................................................. 135
SW2 .................................................................... 130
T
terminal board ..................................................... 152
terminal cover ...................................................... 148
test run ................................................................ 156
thermistor
discharge pipe thermistor ... 27, 28, 39, 103, 143
function ........................................................... 27
heat exchanger thermistor .............. 85, 127, 143
indoor heat exchanger thermistor ............. 27, 28
outdoor air temperature thermistor ............... 103
outdoor heat exchanger thermistor ... 27, 28, 103
radiation fin thermistor .................................. 103
room temperature thermistor .......................... 85
thermistor or related abnormality (indoor unit) ...... 85
thermistor or related abnormality (outdoor unit) .. 102
thermistor resistance check ................................ 116
thermostat control ................................................. 21
TIMER operation ................................................... 63
top panel ............................................................. 136
troubleshooting ................................................ 68, 79
turning speed pulse input on the outdoor unit PCB
check ........................................................... 119
U
U0 ........................................................................ 110
U2 ........................................................................ 112
U4 .......................................................................... 87
UA ......................................................................... 88
unspecified voltage ............................................... 88
V
V1 ...................................................................... 8, 10
V2 .......................................................................... 10
V3 .......................................................................... 10
varistor .................................................................. 10
voltage detection function ..................................... 42
W
wiring diagrams ................................................... 163
iii
SiBE06-514
iv
Index
SiBE06-514
C
compressor lock .....................................................91
compressor protection function ..............................33
compressor system sensor abnormality .................99
control PCB (indoor unit) ..........................................9
control PCB (outdoor unit) .....................................11
D
DC fan lock ............................................................92
DC voltage / current sensor abnormality ..............101
defrost control ........................................................37
diagnosis mode ......................................................77
discharge pipe control ............................................33
discharge pipe temperature control .......................96
discharge pressure check ....................................117
display PCB .............................................................9
E
electrical box temperature rise .............................104
electronic expansion valve check ........................114
electronic expansion valve control .........................38
J
jumper settings .................................................... 157
L
limit switch continuity check ................................ 113
location of operation lamp ..................................... 74
M
mode hierarchy ..................................................... 29
N
night set mode ....................................................... 22
O
OL activation (compressor overload) .................... 90
ON/OFF button on indoor unit ............................... 25
outdoor unit fan system check ............................ 118
outdoor unit PCB abnormality ............................... 89
output over current detection .............................. 108
over-voltage detection ......................................... 112
piping diagrams
FVKS25/35BVMB ......................................... 160
FVXS25/35BVMB ......................................... 160
RKS25D2VMB .............................................. 161
RKS25DVMB ................................................ 161
RKS35D2VMB .............................................. 161
RKS35DVMB ................................................ 161
RXS25D2VMB .............................................. 162
RXS25DVMB ................................................ 162
RXS35D2VMB .............................................. 162
RXS35DVMB ................................................ 162
position sensor abnormality ................................ 100
power supply PCB ................................................... 8
power supply waveforms check .......................... 118
POWERFUL operation .......................................... 24
programme dry function ........................................ 19
SiBE06-514
T
target discharge pipe temperature control .............40
thermistor or related abnormality (indoor unit) .......85
thermistor or related abnormality (outdoor unit) ...102
thermistor resistance check .................................116
thermostat control ..................................................21
trial operation from remote controller ...................156
turning speed pulse input on the outdoor unit PCB
check ............................................................119
U
unspecified voltage
(between indoor and outdoor units) ................88
W
wiring diagrams
FVKS25/35BVMB ..........................................163
FVXS25/35BVMB ..........................................163
RK(X)S25/35D2VMB .....................................163
RK(X)S25/35DVMB .......................................163
vi
Zandvoordestraat 300
B-8400 Ostend - Belgium
www.daikineurope.com
SiBE06-514 09/2005
Prepared in Belgium by Lannoo