Instructions: Select the desired Units of Measurement from the "pull-down" menu.
Required Information:
Units of Measurement
Metric Units
bar diameter
0.1920 mm*
bar spacing
6.0 mm
Slab Thickness, t
concrete compressive strength, f'c
4.0 mm
4000 MPa
60000 MPa
* - for information related to wire and bar sizings, please refer to chart on Tab 2 (tab below)
Minimum requirements:
PCA (note: other documents may provide different minimums)
Minimum % of reinforcing steel for shrinkage reinforcing
Q. is the steel ratio provided greater than the minimum?
4.825 mm2/m
0.121 %
0.100
yes
1000 mm
Estimated concrete flexural strength (change if necessary)
Spread Tensile Strength provided by steel reinforcing, f wwm
Re3 value required to match spread tensile strength
17.6 kg/m3
**
47.4
62.9
198.9
Area of slab
Price of TUF-STRAND SF (installed)* $
465 m2
4.00 /kg
0.28 / m2
NOTICE: Be sure that all manual entries are in the correct units and values as this will have a significant impact on the final dosage and cost.
The value of the TUF-STRAND SF dosage may be adjusted if necessary (depending upon the mixing, safety and performance requirements).
This spreadsheet is only valid to calculated dosage rates up to 11.5 lbs/yd.
NOTE: The solutions provided are to be treated as a recommendation only.
- For more information, please contact The Euclid Chemical Company at 1-800-321-7628.
Notations:
f'c
fy
As
Area of steel per unit area* - Usually expressed per ft length if b is set to 12 in, in 2/ft (mm2/m)
unit width of cross section* - Usually set to 12 in if steel is expressed in in 2/ft (1000 mm)
fwwm
Re3
ASTM C 1018 - Flexural Toughness of Fiber Reinforced Concrete (using beam under third point loading)
age Calculations
e only if necessary
rements
MPa
MPa
%
from required
ASTM C 1018 testing
M or steel option
Metric Units
Reinforcing Bars
Reinforcing Bars
bar size
(mm)
#3 (3/8")
0.375
9.5
#4 (1/2")
0.5
#5 (5/8")
#6 (3/4")
(in)
10M
11.3
0.44
12.7
15M
16.0
0.63
0.625
15.9
20M
19.5
0.77
0.75
19.1
25M
25.2
0.99
bar size
(mm)
0.134
3.40
W1.5
0.138
3.51
W1.7 (9 Ga.)
0.148
W2.0
wire size
(in)
MW 9.1 (W1.4)
3.40
0.134
MW11.1 (W1.7)
3.76
0.148
3.76
MW 13.3 (W2.1)
3.80
0.150
0.160
4.06
MW 16.0 (W2.5)
4.52
0.178
W2.1 (8 Ga.)
0.162
4.11
MW 18.7 (W2.9)
4.88
0.192
W2.5 (7 Ga.)
0.178
4.52
MW 19.2 (W3.0)
4.95
0.195
W2.9 (6 Ga.)
0.192
4.88
MW 22.6 (W3.5)
5.36
0.211
W3
0.195
4.95
MW 25.8 (W4.0)
5.74
0.226
5 Ga.
0.207
5.26
MW 28.9 (W4.5)
6.07
0.239
W3.5
0.211
5.36
MW 32.3 (W5.0)
6.40
0.252
W4 (4 Ga.)
0.226
5.74
MW35.5 (W5.5)
6.73
0.265
W4.5
0.239
6.07
MW 38.7 (W6.0)
7.01
0.276
3 Ga.
0.244
6.20
MW42.1 (W6.5)
7.32
0.288
W5.0
0.252
6.40
MW 45.2 (W7.0)
7.60
0.299
2 Ga.
0.263
6.68
MW 48.4 (W7.5)
7.85
0.309
W5.5
0.265
6.73
MW 51.6 (W8.0)
8.10
0.319
W6 .0
0.276
7.01
1 Ga.
0.283
7.19
W6.5
0.288
7.32
W7.0
0.299
7.59
W7.5
0.309
7.85
W8 .0
0.319
8.10