MEES
SAAV
V II N
NGG D
D EE SS II G
GNN A
A II DD SS
Two-Way Slabs
Design strip
24′-0″
Total panel moment Mo in end span: For simplicity, use Mo = 282.2 ft-kips for all
spans.
w u l 2 l 2n 0.285 × 24 × 18.167 2
Mo = = Division of the total panel moment Mo into
8 8
negative and positive moments, and then
= 282 .2 ft - kips column and middle strip moments, involves
the direct application of the moment
Total panel moment Mo in interior span: coefficients in Table 1.
w u l 2 l 2n 0.285 × 24 × 18.0 2
Mo = =
8 8
= 277 .0 ft - kips
Total
73.4 146.7 197.5 98.8
Moment
Column
73.4 87.5 149.6 59.3
Strip
Middle
0 59.3 48.0 39.5
Strip
Note: All negative moments are at face of support.
TT II M
MEES
SAAV
V II N
NGG D
D EE SS II G
GNN A
A II DD SS
Two-Way Slabs
Required As = 45.5/(4 x 7.75) = 1.47 in.2 For 4-No. 4 within 120 – 47 = 73 in. width:
73/4 = 18.25 in. > 18 in.
Number of No. 4 bars = 1.47/0.2 = 7.4,
say 8 bars Add 1 additional bar on each side of the
47 in. strip; the spacing becomes 73/6 =
Must provide 8-No. 4 bars within an 12.2 in. < 18 in. O.K.
effective slab width = 3h + c2 = (3 x 9) +
20 = 47 in. Reinforcement details at this location are
shown in the figure on the next page (see
Fig. 6).
∗
The provisions of Sect. 13.5.3.3 may be utilized; however, they are not in this example.
TT II M
MEES
SAAV
V II N
NGG D
D EE SS II G
GNN A
A II DD SS
Two-Way Slabs
5′-6″
3-No. 4
Column strip – 10′-0″
3′-11″
8-No. 4
1′-8″
3-No. 4
J/c = 2f2d3 = 2 x 5.53 x 7.753 = 5,148 in.3 bo /d = [(2 x 23.875) + 27.75]/7.75 = 9.74
βc = 1
72, 800 0.38 × 84.7 × 12, 000
vu = +
585 .0 5, 148 φvc = 215 psi > vu = 199.4 psi OK
v u = 124 .4 + 75 .0 = 199 .4 psi
Reinforcement Details
Determine allowable shear stress φvc from
The figures below show the reinforcement
Fig. 4b:
details for the column and middle strips.
The bar lengths are determined from
bo /d = (2b1 + b2)/d
Fig. 13.3.8 of ACI 318-99.
1′-8″ 5′-6″ 5′-6″ 2′-0″ 5′-6″
3′-8″ 3′-8″
12-No. 4
14-No. 4 13-No. 4
Standard
hook (typ.)
6″ 2-No. 4 13-No. 4 Class A tension splice
Column strip
20′-0″
14-No. 4 14-No. 4
Standard
hook (typ.) 6″
7-No. 4
6″ 7-No. 4 7-No. 4 7-No. 4
3′-0″
Middle strip
20′-0″