12.
8. (5mm deep)
5.5
6.
6.
4.
5.5
25.
52.
21.
21.
19.5
15.
8.
16.
15.
4.
6.5
9.125
6.
2.4
C
2.
22.
Unless Otherwise Specified:
Dimensions in mm
Tolerances:
Angular: 0.5 Nominal: 0.5
One Decimal Place 0.1
Two Decimal Places 0.05
Name
Drawn
H Thomas
Debur and
Break Sharp
Edges
Finish
Bright
Date
Mar / 9 / 13
Comments
CAD Generated Drawing
Do Not Manually Update
QTY
1
Checked
D
Arm (block)
pre-drill holes in these locations in arm block
ENG Appr.
MFR Appr.
Material
QA
12 x 25 aluminium flat
1
Size
A4
Scale
Drawing No.
Rev
01-BLOCK
1:1
CAD File
A
Sheet
1 of 5
9.5
3.5
4.
4.5
29.
13.
10.
2.5
5.5
11.
15.
10.5
14.
9.5(2mm deep)
2.
3.
2.
2.5
39.
6.
10.5
M3 (3mm hole top, tap bottom)
2.5
39.
52.
Unless Otherwise Specified:
Dimensions in mm
Tolerances:
Angular: 0.5 Nominal: 0.5
One Decimal Place 0.1
Two Decimal Places 0.05
Drawn
Debur and
Break Sharp
Edges
Finish
Bright
Name
Date
Comments
H Thomas
Mar / 9 / 13
QTY
1
Checked
D
Arm
Use 8mm and 4mm 2 flute end mills
ENG Appr.
MFR Appr.
Material
QA
12 x 25 aluminium flat
1
Size
A4
Scale
Drawing No.
Rev
02-ARM
1:1
CAD File
A
Sheet
2 of 5
9.5
A
3.5
4.
4.5
52.
42.
13.
10.
2.5
3.
52.
10.5
5.5
11.
15.
3.5
39.
14.
14.
2.
M3 (3mm hole top, tap bottom)
2.5
6.
4.
12.
4.5
10.5
13.
Drawn
Debur and
Break Sharp
Edges
Finish
Bright
Name
Date
Comments
H Thomas
Mar / 9 / 13
QTY
1
Checked
D
Arm (variant)
Use 8mm and 4mm 2 flute end mills
ENG Appr.
MFR Appr.
Material
QA
12 x 25 aluminium flat
1
Size
A4
Scale
Drawing No.
Rev
02-ARM2
1:1
CAD File
A
Sheet
2 of 5
3.
12.
15.
42.
29.
31.
3.
5.5
5.5
5.
32.
5.5
10.
4.5
10.
3.
19.
5.
32.
3.
22.
12.
3.
15.
9.
10.
32.
Drawn
Debur and
Break Sharp
Edges
Finish
Bright
Name
Date
Comments
H Thomas
Mar / 9 / 13
QTY
1
Checked
D
Base plate
mill (or cut and file)
ENG Appr.
MFR Appr.
Material
QA
3 x 32 aluminium angle
1
Size
A4
Scale
Drawing No.
Rev
03-BASE
1:1
CAD File
A
Sheet
3 of 5
8.
6.
5.
B
3.
14.
3.
C
Drawn
Debur and
Break Sharp
Edges
Finish
Bright
Name
Date
Comments
H Thomas
Mar / 9 / 13
Checked
D
QTY
Pin
turn
ENG Appr.
MFR Appr.
Material
QA
9mm Round
1
Size
A4
Scale
Drawing No.
Rev
04-PIN
1:1
CAD File
A
Sheet
4 of 5
42.
A
5.5
5.5
31.
5.5
21.
21.
15.
32.05
2.
Drawn
Debur and
Break Sharp
Edges
Finish
--
Name
Date
Comments
H Thomas
Feb / 9 / 2013
QTY
1
Checked
D
Extruder Dimensions
Design constraints
ENG Appr.
MFR Appr.
Material
QA
-1
Size
A4
Scale
Drawing No.
Rev
05-CONSTRAINTS
1:1
CAD File
A
Sheet
5 of 5