ffitreII
d
@":!!11 engineered
THf SrlAXEn$ Sr
&msscm$EffiKt*
f*a.%s

&r*??ffi#*&Ke
?ubs lnsl*lat**n
Sr*per Moisture fforltnol, M*ld-**s*st*nt
s
Clss*****li, **nwieking
E M icrc
**t
pr*t*eti*r"r
* Sib*r*fr**
w
Wg SUPPORT
ffi
&# @'e'Mw,F.m
slrrrrf,r3
APPROVED
Tub* $nsu3ati*r:
refrigeration lines
Description
-:::)
:,,
.. .,
,,
,3/4:,1" andl-1/T
,,,,.....,.t,:
.,.
Uses
r Retards
. Acceptable
protection
Xmsux8m&Xwxx
requirements
The recommended temperature usage range forAP Armaflex
Pipe lnsulation is -297"F to +220'F (-183"C to +105"C). For use
on cold pipes, thicknesses have been calculated to control
condensation on the insulation outer surface, as shown in
the table of thickness recommendations. AP Armaflex meets
the energy code requirements of ASHRAE 901, ASHRAE 90.2
lnternational Energy Conservation Code (IECC) and other
building codes.
rl'
:lApplication
:r:'"r,,'
with adhesive.
For pipes greater than 6" lPS, use AP/Armaflex SheeVRoll
insulation. For thicknesses greater than 1", sleeve the insulation.
See technical bulletin #030 for additional information.
AP/Armaflex pipe insulation is available in1-1/T wall thicknesses
with 25150 rating for lD size range from 7/t to 4'lPS.
AP Armaflex normally requires no supplemental vapor-retarder
..'ae*iil;i1on comeli;;;e.''
,,
ASTMC534,Typel-
ASTM D.1056,281
Tubular Grade 1
ASTM E 84, NFPA255,UL723
CAN/ULC S102
UL 94 5V-5A, V-O, File E 55798
MIL-P-15280J, FORM T
Ul181
ASTM G-21lC'1338,
ASTM G-22
City of LA-RR7642
\-,
\-
F*ngrsleal Fropen*ies
i].faii,,method,,,
,,,,.,
,,,1
Notes
O On the heating cycle, AP Armaflex
Pipe lnsulation will withstand
i
i
(105.C).
-J__,._.
I
I
l-ll2"
25/50
ASTM G21lC1338
ASTM G22
Meets requirements
Meets requirements
Meets requirements
O.2o/o
ASTM C 209
220"F (105'C)
UL181
ASTM E 84
CAN/ULC 5102
Mold Growth
Fungi Resistance
Bacierial Resistance
O Reference only
* For applications
ol -40'F to -2W"F
(-40'C to {83"C), contact Armacell.
Performance approved through
continuing supervision by Factory
Mutual Approvals.
Sizes
Wall Thickness, (nominal) Form
1',
1-1/r (0,
38mm)
tt+mm)l
! 6 (1.8m)
l1-1//watt;3
(0.sm)l
i-
Rw*mxxNffi?*x?Sffi*&mrxm
Pip.6
Size
3/ff
L-
/{
gei3-!i{lqffiL_
t'-*-?:"ery.e*---!li"a:1
5grp(to'G)
:35"F (2ecl
Nom
Nom
Nom
Nom
1/Z(13mm)
1/Z(13mm)
1/Z(13mm)
3/4'(19mm)
0"F-,(-t8.cl
Nom
Nom
Nom
Nom
.:
']:-2!9Fr,p29bO)
3/4'(19mm)
Nom 1"(25mm)
Nom 1"(25mm)
Nom 1-114. (32mm)
Nom 1-114'(32mm)
1"(25mm)
1"(25mm)
1"(25mm)
'j
Nom 1"(25mm)
Nom 1"(25mm)
i Nom 3/4:(19mm)
i Nom 3/4: (19mm)
NOTE: Thicknesses greater than 1" (25mm) are multiple-layer applications, see technical bulletin #30.
.BASED
ON NORMAL DESIGN CONDITIONS AP Armaflex in the thicknesses noted and within the specified temperature ranges will control outer insulation
surface condensation indoors under. normal design conditions, a maximum.severity of 85"F (29'G) and 70% tiH. Armacell-research and field experience
indicate that indoor conditions anywhere in the United States seldom exceed this degree of severity.
*BASED ON MILD DESIGN COND|IIONS AP Armaflex in the thicknesses noted and within the specified
temperature ranges will control outer insulation surface
condensation indoors under mild design conditions, a maximum severity of 8O"F (27"C) and 50% RH. Typical of these Conditions are most air-conditioned
spaces and arid climates.
*BASED ON SEVERE
DESIGN CONDITIONS AP Armaflex in the thicknesses noted and wiihin the specified temperature ranges will control outer insulation
surface condensation indoors under severe design conditions, a maximum severity of 90'F (32'C) and 8O% RH. Typical of these conditions are indoor areas in
which excessive moisture is introduced or in poorly ventilated confined areas where the temperature may be depressed below ambient.
.::
wlA/w,armae*ll.comlus
Fcr the latest Cocurneni, please refer to cr-;r website.
:t:
dd\
lr
ce
ff.svarTn3
-@i' engins6red
foa
s
*w.
tTl
ilr*
tilatrF*8 0?
AnmeFEex@
lIlbFF----
www.armacell.com
upon the other source(s) to provide accurate information. lnformation provided as a result of Armaoell's own technical analysis and testing is accurate to the extent of our
to which the user may convey the products. Slnce Armacell cannot control the end use of this product, Armacell does not guarantee that the user will obtain the same resuhs as
published in this do'cument. The data and information are provided as a technical service and are subject to change without notice.
Microban is a registered trademark of Microban Products Company
ffi
O 2008 Armacell
[-C