Anda di halaman 1dari 6

This can be used for CE Cong Issue Troubleshooting

(Huawei)

CS RRC & RAB Accessibility Algorithm Overview


CS RRC & RAB Accessibility
Failure
Radio Network
Failures
RRC Call
Admission
Control
Failure

RF
Coverage
Condition
Problem

Transport Network
Failures
Iub
Transmissio
n Problem

Other
Transmissio
n Problem

RRC & RAB Setup Fail due to Code Admission Failure


RRC & RAB Setup Fail due to UL CE Admission
Failure
RRC & RAB Setup Fail due to DL CE Admission
Failure
RRC & RAB Setup Fail due to UL Iub Admission
Failure
RRC & RAB Setup Fail due to DL Iub Admission
Failure
RRC & RAB Setup Fail due to UL Power Admission
Failure
RRC & RAB Setup Fail due to DL Power Admission
Failure

RRC & RAB Setup Fail due to UL\DL CE Admission Failure:

Check on Current Cell and Recommendations


1. Check the CS Voice Traffic and CS Video Traffic (KPI), if there is a sudden
increase of CS Voice or Video traffic compared with previous week => High
CS Traffic Increase noticed
2. Check the PS R99 UL Traffic and HSUPA RLC Traffic (KPI), if there is a sudden
increase of PS traffic compared with previous week => High Data Traffic
Increase noticed
3. Check whether this cell is a pilot polluter (feature), and the SHO Ratio (KPI), if
this cell is a pilot polluter or SHO Ratio > 40% => Recommend to modify the
E1a/E1b parameter to reduce the SHO ratio.

Proposed Parameter: (1st Batch)- INTRARELTHDFOR1BCSNVP Changed from 12 to 10 and INTRARELTHDFOR1BPS - Changed
from 12 to 10. Both INTRARELTHDFOR1BCSNVP and INTRARELTHDFOR1BPS were
changed to increase

Probabilities of Triggering event 1B and improve SHO Overhead

Proposed Parameter: (2nd Batch)- TRIGTIME1B- 640 -> 320(ms)


Trigger will be shorten time to remove links from active set criteria is fulfilled.

4. Check the Best Effort Traffic Initial Access Rate- RNC Level Parameter
(UlBeTraffInitBitrate, DlBeTraffInitBitrate), Modify the DCH initial access
rate/DCCC rate threshold/low activity bit rate threshold from 64kbps to 32
kbps.
o SET UFRC: UlBeTraffInitBitrate=D32, DlBeTraffInitBitrate=D32;
o SET UDCCC: UlDcccRateThd=D32,
DlDcccRateThd=D32,LittleRateThd=D32;
5. Check the UL HSUPA Traffic Initial Access Rate (HsupaInitialRate), Modify the
HSUPA initial access rate/DCCC uplink bit rate threshold/low activity bit rate
threshold from 64kbps to 32 kbps.
o SET UFRC: HsupaInitialRate =D32;
o SET UEDCHRATEADJUSTSET: EdchRateAdjustSet=RATE_32KBPS1&RATE_128KBPS-1&RATE_608KBPS-1;
6. Check the UL GBR setting (RNC Level Parameter), if the parameter is greater
than 32kbps, => Recommend to change the UL GBR to 32kbps for all GBR
related services.
UL GBR setting: SET USERGBR:TRAFFICCLASS=BACKGROUND,
BEARTYPE=R99, USERPRIORITY=SILVER, <ULGBR>=D32;
UL GBR setting: SET USERGBR:TRAFFICCLASS=BACKGROUND,
BEARTYPE=R99, USERPRIORITY=GOLD, <ULGBR>=D32;
UL GBR setting: SET USERGBR:TRAFFICCLASS=BACKGROUND,
BEARTYPE=R99, USERPRIORITY=COPPER, <ULGBR>=D32;
UL GBR setting: SET USERGBR:TRAFFICCLASS=BACKGROUND,
BEARTYPE=HSPA, USERPRIORITY=SILVER, <ULGBR>=D32;
UL GBR setting: SET USERGBR:TRAFFICCLASS=BACKGROUND,
BEARTYPE=HSPA, USERPRIORITY=GOLD, <ULGBR>=D32;
UL GBR setting: SET USERGBR:TRAFFICCLASS=BACKGROUND,
BEARTYPE=HSPA, USERPRIORITY=COPPER, <ULGBR>=D32;

RNC Level (apply on Traffic Class/THP/Bear Type/User Priority level

7. Check and Modify the DCH/HSUPA DCCC 4A threshold and limit user rate
upgrade,
For DCH BE Service, 4A threshold default value is
1K for each rate.It need to confirm what is the appropriate 4A value in order
limit rate upgrade.
For Example:
o MOD UTYPRABDCCCMC:
RabIndex=43,Direction=UPLINK,Event4aThd=D2K;//Assume 43 is index
of interactive Service 32kbps,4A threshold is modified to 2K
o MOD UTYPRABDCCCMC: RabIndex=45,Direction=
UPLINK,Event4aThd=D6K;// Assume 45 is index of interactive Service
128kbps,4A threshold is modified to 6K
For HSUPA BE Service, it can modified HSUPA DCCC threshold rate ratio to
higher value for different rate.
For Example:
o

SET UEDCHTHDRATERATIO: RatioForRate128=100;\\Modify 128kbps DCCC rate


ratio to 100%.

8. Enable the TTI Dynamic adjustment algorithm for admission CE-Based HSUPA
Services.
o SET UCORRMALGOSWITCH:
DraSwitch=DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH-1;\\ TTI Switch
o MOD UCELLLDR: CellId=1111,UlTtiCreditSfResThd=SF8;\\TTI
Reconfigure Cell Threshold
o MOD UNODEBLDR: NodeBName= aaaa,
UlTtiCreditSfResThd=SF8;\\TTI Reconfigure NodeB Threshold
9. Enable PS BE\HSDPA\HSUPA state transition.
o SET UCORRMALGOSWITCH:
DraSwitch=DRA_HSDPA_STATE_TRANS_SWITCH1&DRA_HSUPA_STATE_TRANS_SWITCH-1&PS_BE_STATE_
TRANS_SWITCH-1;
10.Modify Credit SF reserved threshold (ULHOCERESVSF, DLHOCECODERESVSF)
from (SF16->SF32 ,SF32->SF64).It Reducing CE consume for Uplink
/Downlink for handovers.
11.Check Rate Control Switch Parameter- RNC Level Parameter (RNC Level
Parameter), if DCCC feature is disabled => Recommend to enable DCCC
feature to alleviate code resource usage.
Rate Control Switch Parameter: SET CORRMALGOSWITCH:
DraSwitch=<DRA_DCCC_SWITCH>-1
12.Check Rate Control Switch for HSUPA status (Parameter), if DCCC for HSUPA is
disabled => Recommend to enable DCCC for HSUPA feature to alleviate
channel element resource usage
o SET CORRMALGOSWITCH: DraSwitch=<DRA_HSUPA_DCCC_SWITCH>-0;
13.Check Load Control Switch Parameter and Load Control Action (Parameter), if
Load Control feature is disabled => Recommend to enable load control to

alleviate code resource usage. Make actions of Rate Adjustment and InterFreq LDHO higher priority over other actions
//Enabling load reshuffling algorithms
1) MOD UCELLALGOSWITCH: CellId=100, NBMLdcAlgoSwitch=UL_UU_LDR1&DL_UU_LDR-1&CELL_CODE_LDR-1&CELL_CREDIT_LDR-1;
2)SET ULDCALGOPARA: LdcSwitch=NODEB_CREDIT_LDR_SWITCH1&LCG_CREDIT_LDR_SWITCH-1;
3)MOD UNODEBALGOPARA: NodeBName="nodeb1", NodeBLdcAlgoSwitch=IUB_LDR1&NODEB_CREDIT_LDR-1&LCG_CREDIT_LDR-1;

//Setting load reshuffling thresholds


MOD UCELLLDM: CellId=100, UlLdrTrigThd=55, UlLdrRelThd=45;\\ for
UL
MOD UCELLLDM: CellId=100, DlLdrTrigThd=50, DlLdrRelThd=40; \\ for
DL

//Setting LDR Action Priorty:


MOD UCELLLDR: CellId=100, UlLdrFirstAction=BERateRed,
UlLdrSecondAction=InterFreqLDHO ; \\ for UL
MOD UCELLLDR: CellId=100, DlLdrFirstAction=BERateRed,
DlLdrSecondAction=InterFreqLDHO ; \\ For DL

//Turning on load reshuffling function switches


SET UCORRMALGOSWITCH: DraSwitch=DRA_DCCC_SWITCH-1;

14.Check Average RB Number of Voice User, Average RB Number of Video User,


Average RB Number of UL PS R99, Average HSUPA User Number (KPI), such
as Voice, Video, PS64/128/384, HSUPA, calculate the UL CE Usage for each
service, => point out the service that consumes maximal UL CE
15.Check RRC Redirection feature status (Parameter), if it is disabled =>
recommend to enable this feature.
o RRC Redirection Feature Switch:
ADD CELLREDIRECTION: CellId=0, TrafficType=AMR,
<RedirSwitch>=ONLY_TO_INTER_FREQUENCY;

16.Check RRC DRD feature status (RNC Level Parameter), if it is disabled =>
recommend to enable this feature
o RRC DRD Feature Switch:
SET CORRMALGOSWITCH: DrSwitch=<DR_RRC_DRD_SWITCH>-1;
17.Check Cell Peak UL CE Usage (KPI) and calculate the NodeB UL CE Mean
Usage Ratio (KPI) for the past 2 weeks, if Cell Peak UL CE Usage > 80% and
NodeB UL CE Mean Usage Ratio (KPI) >70% for more than 7 days, and if RRC
Redirection and RRC DRD feature (Parameter) are enabled => Continuous
High UL CE Usage is noticed, and it is recommended to increase UL CE
Configuration
o RRC Redirection After RRC DRD Fail Feature Switch:
SET DRD: <ConnectFailRrcRedirSwitch>=Allowed_To_Inter_RAT;

Check on Current Cells Match Azimuth cells :


1. Check the Match Azimuth Neighbor Cell current cell status (MML
Command), if its status is not Active, => Neighbor Cell is in abnormal status
2. Check whether the Match Azimuth Neighbor Cell is sleeping cell (feature), if
it satisfies the sleeping cell criteria, => Neighbor Cell is in Sleeping Cell
status
3. Check whether the Match Azimuth Neighbor Cell is weak coverage
(feature), if it satisfies weak coverage criteria => Neighbor Cell has weak
coverage which may increase unnecessary load in current cell
4. Check the Match Azimuth neighbor cell current alarms (alarm), if there is
any transmission related critical alarms, => list the brief information of these
alarms

For DL CE Cong one good case to resolve the Issue:


1.

Check Cell Peak DL CE Usage for this cell (KPI) and calculate the NodeB Mean
DL CE Usage Ratio for the past 2 weeks, if Cell Peak DL CE Usage>80% and
NodeB Mean DL CE Usage Ratio (KPI) >70% for more than 7 days, and if RRC
Redirection and RRC DRD feature (Parameter) are enabled => Continuous
High DL CE Usage is noticed, and it is recommended to increase DL CE
Configuration

Anda mungkin juga menyukai