product data
SELECTION DATA
GENERIC TYPE: Aliphatic acrylic polyurethane Part A and Part
B mixed prior to application.
GENERAL PROPERTIES: Carbothane 134 ZA is a glossy, tilelike, attractive topcoat, produces a smooth, slick and hard film
which is readily cleaned. Carbothane 134 ZA has very good
resistance to splash and spillage of acids, alkalies and most
solvents. It exhibits excellent resistance to splash and spillage
of salts and water.
Excellent weatherability
Excellent flexibility
RECOMMENDED USES: Recommended as a finish coat for
exteriors of tanks, equipment, piping, structural steel and
concrete surfaces where chemical resistance, toughness and
weatherability are required. Carbothane 134 ZA is an excellent
coating for use in chemical processing, pulp and paper,
petrochemical, offshore drilling and similar demanding industries.
Carbothane 134 ZA also finds many applications in areas of
heavy marine, institutional and waste treatment where a highly
resistant and attractive coating is required.
NOT RECOMMENDED FOR: Immersion service.
SPECIFICATION DATA
THEORETICAL SOLIDS CONTENT OF MIXED
MATERIAL:
By Volume
48% 2%
Fumes
Excellent
Excellent
Excellent
Excellent
Excellent
ORDERING INFORMATION
Prices may be obtained from your StonCor Africa Sales
Representative or StonCor Africa Customer Service.
APPROXIMATE SHIPPING WEIGHT:
5L
Carbothane 134 ZA
7,0 kg
Carboline Thinner # 25
4,9 kg
FLASH POINT (Pensky-Martens Closed Cup):
Carbothane 134 ZA Part A
17C
Carbothane 134 ZA Part B
33C
Carboline Thinner # 25
23C
To the best of our knowledge the technical data contained herein are true and accurate at the date of issuance and are subject to change without prior
notice. User must contact StonCor Africa to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We
guarantee our products to conform to StonCor Africa quality control. We assume no responsibility for coverage, performance or injuries resulting
from use. Liability, if any, is limited to replacement of products. Prices and cost data, if shown , are subject to change without prior notice. NO OTHER
WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY STONCOR AFRICA, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW OR
OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
APPLICATION INSTRUCTIONS
These instructions are not intended to show product recommendations for specific service. They are issued as an aid in determining correct surface
preparation, mixing instructions and application procedure. It is assumed that the proper product recommendations have been made. These
instructions should be followed closely to obtain the maximum service from the materials.
5lt Kit
4,375lt
0,625lt
Surfaces
18-29C
10C
54C
Ambient
16-29C
10C
49C
AIRLESS:
Pump Ratio
Material Hose
Tip Size
Output psi
Filter Size
30:1 (min)*
10mm I.D. (min)
0,013 to 0,015
2100 to 2300 (145-159 Bar)
60-100 mesh
Normal
Minimum
Maximum
Humidity
35-80%
0%
85%
Dry to Handle
6 Hours
3 Hours
1 Hours
Final Cure
10 Days
1 Week
5 Days
CAUTION: MAY CONTAIN FLAMMABLE SOLVENTS. KEEP AWAY FROM SPARKS AND OPEN FLAMES. IN CONFINED AREAS WORKMEN MUST WEAR
FRESH AIRLINE RESPIRATORS. HYPERSENSITIVE PERSONS SHOULD WEAR GLOVES OR USE PROTECTIVE CREAM. ALL ELECTRONIC
EQUIPMENT AND INSTALLATIONS SHOULD BE MADE AND GROUNDED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE. IN AREAS
WHERE EXPLOSION HAZARDS EXIST, WORKMEN SHOULD BE REQUIRED TO USE NONFERROUS TOOLS AND TO WEAR CONDUCTIVE
AND NONSPARKING SHOES.
Africa
An
Company