Features
Ordering Information
TEMP RANGE
PIN-PACKAGE
MAX1501ETE
PART
-40C to +85C
16 Thin QFN
MAX1501ZETE
-40C to +85C
16 Thin QFN
1F
BATT
10F
INP
Applications
MAX1501/MAX1501Z
FULLI
PDAs
Digital Cameras and MP3 Players
USB Appliances
Charging Cradles and Docks
GLED
VL
RLED
SELV
TEMP
MODE
TMAX/I.C.
Bluetooth Equipment
CHGEN
RPULLUP
SETI
ACOK
2.8k
VLOGIC
( 5.5V)
GND
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxims website at www.maximintegrated.com.
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
ABSOLUTE MAXIMUM RATINGS
IN, INP, RLED, GLED to GND ................................-0.3V to +14V
IN to INP ................................................................-0.3V to +0.3V
VL, BATT, SETI, ACOK, MODE, CHGEN, SELV,
FULLI, TMAX/I.C., TEMP to GND .........................-0.3V to +6V
VL to IN...................................................................-14V to +0.3V
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = VINP = 5V, VBATT = 3.5V, ACOK = GLED = RLED = TEMP = TMAX/I.C. = FULLI = open, CHGEN = MODE = GND, RSETI = 2.8k,
CIN = 1F, CBATT = 10F, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
13
4.50
6.25
V
V
2.7
3.3
40
70
100
30
55
85
VL Output Voltage
4.05
4.125
4.20
VIN falling
3.9
4.025
4.1
VIN rising
6.25
6.50
6.75
1.5
Hysteresis
100
80
VIN = 0
10
Disable mode
Disable mode
NiMH/NiCd mode
V
mA
0.25
45
V
mV
VBATT = 4.3V
Li+ mode
mV
15
75
VIN rising
IN Input Current
UNITS
1.4
SELV = VL
4.166
4.2
4.234
SELV = GND
4.067
4.1
4.133
SELV = VL,
VIN = VINP = 6V
4.85
4.95
5.05
SELV = GND
4.4
4.5
4.6
No-battery mode
3.700
4.0
4.234
BATT rising
2.675
2.8
2.925
RSETI = 2.8k
460
500
540
RSETI = 1.75 k
736
800
864
Fast-Charge Current-Loop
System Accuracy
mA
Maxim Integrated
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
ELECTRICAL CHARACTERISTICS (continued)
(VIN = VINP = 5V, VBATT = 3.5V, ACOK = GLED = RLED = TEMP = TMAX/I.C. = FULLI = open, CHGEN = MODE = GND, RSETI = 2.8k,
CIN = 1F, CBATT = 10F, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.)
PARAMETER
Precharge Current System
Accuracy
Die Temperature Regulation
Setpoint (Note 1)
CONDITIONS
% of fast-charge current, VBATT = 2V
MIN
TYP
MAX
UNITS
10
15
TEMP = GND
95
TEMP = open
115
TEMP = VL
Current-Sense Amplifier Gain
0.70
1.30
0.95
1.05
84
1.25
CHGEN, MODE
100
SELV
100
50
V RLED = 1V
V GLED = 1V
14
% of fast-charge
current
Li+ mode
NiMH/NiCd mode
Charge-Timer Accuracy
Charge-Timer Duration
(MAX1501 Only)
Maxim Integrated
190
mA/A
m
350
mV
0.52
175
400
175
400
90
200
10
18
mA
20
34
mA
0.1
15
VVL/2
FULLI = GND
10
FULLI = VL
15
20
25
FULLI = open
25
30
35
SELV = VL
3.9
4.0
4.1
SELV = GND
3.8
3.9
4.0
3.9
4.0
4.1
-10
+10
TMAX = GND
TMAX = open
4.5
TMAX = VL
135
Internal Current-Sense
Resistance
V
%
hrs
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
ELECTRICAL CHARACTERISTICS
(VIN = VINP = 5V, VBATT = 3.5V, ACOK = GLED = RLED = TEMP = TMAX/I.C. = FULLI = open, CHGEN = MODE = GND, RSETI = 2.8k,
CIN = 1F, CBATT = 10F, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
PARAMETER
CONDITIONS
UNITS
13
6.25
2.7
3.3
40
100
30
85
75
4.00
4.25
VIN falling
3.90
4.15
6.25
6.75
Disable mode
VBATT = 4.3V
80
VIN = 0
10
Disable mode
Disable mode
Li+ mode
Battery Regulation Voltage
NiMH/NiCd mode
SELV = VL
4.148
mV
A
VIN rising
V
V
mA
1.4
4.252
SELV = GND
4.05
4.15
SELV = VL
4.85
5.05
SELV = GND
4.4
4.6
No-battery mode
3.700
4.234
BATT rising
2.675
2.925
RSETI = 2.8k
460
540
RSETI = 1.75k
736
864
15
Fast-Charge Current-Loop
System Accuracy
Precharge Current System
Accuracy
Current-Sense Amplifier Gain
MAX
TYP
4.50
MIN
0.60
1.40
0.93
1.07
mA
%
mA/A
350
mV
0.52
1.3
CHGEN, MODE
100
400
SELV
100
400
50
200
Maxim Integrated
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
ELECTRICAL CHARACTERISTICS (continued)
(VIN = VINP = 5V, VBATT = 3.5V, ACOK = GLED = RLED = TEMP = TMAX/I.C. = FULLI = open, CHGEN = MODE = GND, RSETI = 2.8k,
CIN = 1F, CBATT = 10F, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = +25C.) (Note 2)
MAX
UNITS
PARAMETER
V RLED = 1V
CONDITIONS
MIN
7
18
mA
V GLED = 1V
14
34
mA
+10
Charge-Timer Accuracy
(MAX1501 Only)
TYP
-10
2.5
2.0
1.5
1.0
0.5
0
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
300
250
200
150
100
50
0
CHARGE CURRENT
vs. BATTERY VOLTAGE
CHARGE CURRENT
vs. INPUT VOLTAGE
CHARGE CURRENT
vs. INPUT-VOLTAGE HEADROOM
400
350
300
250
200
150
100
50
0
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
BATTERY VOLTAGE (V)
Maxim Integrated
600
550
500
450
Li+ MODE,
SELV = VL,
RSETI = 2.7k
400
350
300
250
200
150
100
50
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13
INPUT VOLTAGE (V)
600
550
CHARGE CURRENT (mA)
500
450
MAX1501 toc04
0 1 2 3 4 5 6 7 8 9 10 11 12 13
MAX1501 toc03
400
350
0 1 2 3 4 5 6 7 8 9 10 11 12 13
600
550
CHARGE CURRENT (mA)
1.6
550
500
450
500
450
400
MAX1501 toc06
3.0
600
3.5
1.8
MAX1501 toc05
4.0
2.0
CHARGE CURRENT
vs. BATTERY VOLTAGE
MAX1501 toc02
Li+ MODE OR
NiMH/NiCd MODE,
SELV = VL, IBATT = 0
4.5
5.0
MAX1501 toc01
350
300
250
200
150
100
50
0
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
VIN - VBATT (V)
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
Typical Operating Characteristics (continued)
(VIN = VINP = 5V, ACOK = RLED = GLED = TEMP = TMAX/I.C. = FULLI = open, CBATT = 10F, CIN = 1F, TA = +25C, unless
otherwise noted.)
BATTERY REGULATION VOLTAGE
vs. TEMPERATURE
3.0
2.5
2.0
1.5
1.0
0.5
Li+ MODE
4.20
4.16
4.14
4.12
4.08
10
35
60
CHARGE CURRENT
vs. AMBIENT TEMPERATURE
CHARGE CURRENT
vs. AMBIENT TEMPERATURE
1000
MAX1501 toc09
900
800
CHARGE CURRENT (mA)
-15
TEMPERATURE (C)
540
520
500
480
460
700
600
85
500
400
300
440
200
420
100
400
0
-40
-15
10
35
60
-40
600
560
SELV = GND
4.10
0 1 2 3 4 5 6 7 8 9 10 11 12 13
580
SELV = VL
4.18
MAX1501 toc10
3.5
4.22
MAX1501 toc08
NO BATTERY MODE
IBATT = 0
4.0
MAX1501 toc07
85
-40
-15
10
35
60
85
Maxim Integrated
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
Pin Description
PIN
NAME
INP
IN
3, 13
GND
SETI
Current-Sense Transconductance Amplifier Output. Connect a resistor from SETI to GND to program the
maximum charge current and to monitor the actual charge current. SETI pulls to GND during shutdown.
VL
Linear Regulator Output. Connect CHGEN, TEMP, TMAX, FULLI, and MODE to VL to program logic high.
VL discharges to GND during shutdown.
TMAX
Maximum Charging-Time Select Input (MAX1501 Only). TMAX sets the maximum charging time. Connect
TMAX to GND to set the maximum charging time to 3 hours. Leave TMAX floating to set the maximum
charging time to 4.5 hours. Connect TMAX to VL to set the maximum charging time to 6 hours. TMAX
pulls to GND through a 50k resistor in shutdown.
I.C.
FUNCTION
High-Current Charger Input. Connect an AC adapter to INP and IN as close to the device as possible.
INP provides charge current to the battery. INP draws current while the device is in shutdown mode.
Low-Current Charger Input. Bypass IN to GND with a 1F ceramic capacitor. Connect IN to INP as close
to the device as possible. IN powers the internal LDO and reference. IN draws current while the device is
in shutdown mode.
FULLI
Top-Off-Current Select Input. FULLI sets the end-of-charge threshold as a percentage of the fast-charge
current. Connect FULLI to GND to set the end-of-charge threshold to 10% of the fast-charge current.
Connect FULLI to VL to set the end-of-charge threshold to 20% of the fast-charge current. Leave FULLI
floating to set the end-of-charge threshold to 30% of the fast-charge current. FULLI pulls to GND through
a 50k resistor in shutdown.
TEMP
Die Temperature Select Input. TEMP sets the die temperature regulation point for the thermal-control
loop. Connect TEMP to GND to regulate the die temperature at +95C. Leave TEMP floating to regulate
the die temperature at +115C. Connect TEMP to VL to regulate the die temperature at +135C. TEMP
pulls to GND through a 50k resistor in shutdown.
MODE
Mode Select Input. MODE and CHGEN together control charging functions (Table 1). An internal 175k
pulldown resistor pulls MODE low.
10
CHGEN
11
ACOK
Input Voltage Range Indicator. The open-drain ACOK output asserts low when 4.2V VIN 6.25V and
VIN - VBATT 100mV. ACOK requires an external 100k pullup resistor. ACOK floats in shutdown.
12
BATT
Battery Connection. Connect the positive terminal of the battery to BATT. BATT draws less than 5A
during shutdown.
14
SELV
Battery Voltage Selection Input. SELV sets the battery regulation voltage in Li+ and NiMH/NiCd modes
(Table 2). For no-battery mode, the battery voltage defaults to 4.0V. An internal 175k resistor to VL pulls
SELV high.
RLED
Battery Charging Indicator. Connect the anode of a red LED to IN and the cathode to RLED. RLED
asserts low when the input supply is present and the battery is charging, regardless of cell chemistry.
RLED sinks 10mA. RLED goes high impedance in shutdown. Connect a pullup resistor to the Ps I/O
supply when interfacing with a P logic input.
GLED
Full-Charge Indicator. Connect the anode of a green LED to IN and the cathode to GLED. GLED asserts
low when the input supply is present and the battery has reached the top-off current threshold set by
FULLI, regardless of cell chemistry. GLED sinks 20mA. GLED goes high impedance in shutdown.
Connect a pullup resistor to the Ps I/O supply when interfacing with a P logic input.
15
16
Maxim Integrated
Charge Enable Input. CHGEN and MODE together control charging functions (Table 1). An internal
175k pulldown resistor pulls CHGEN low.
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
MAX1501/MAX1501Z
INP
BATT
VREF
CS
OUTPUT DRIVER
AND LOGIC
SETI
TEMP REF
TEMPERATURE
SENSOR
IREF
IN
SHUTDOWN
UVLO
VL
CHGEN
VL
MODE
REF
SELV
OVLO
ON
LOGIC
TEMP
ACOK
RLED
FULLI
GLED
OSC
GND
TMAX/I.C.
GND
Maxim Integrated
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
MAX1501 ONLY
OFF
ACOK = HIGH
CHARGER OFF
ACOK = LOW
RLED = OFF
GLED = OFF
ACOK = (4.2V < VIN < 6.25V) AND (VIN - VBATT > 100mV)
ACOK = LOW
CHGEN = LOW
VBATT < 2.8V
CHGEN = HIGH
MODE = LOW
PREQUAL
DISABLE
CHARGER OFF
ACOK = LOW
RLED = OFF
GLED = OFF
CHGEN = LOW
SOFT-START
NOBATT
(CURRENT LIMITED AND
CHGEN = LOW THERMALLY PROTECTED)
ACOK = LOW
RLED = OFF
GLED = OFF
CHGEN = HIGH
MODE = HIGH
SOFT-START
FAST CHARGE
(THERMALLY PROTECTED)
100% SETI CURRENT
ACOK = LOW
RLED = ON
GLED = OFF
TOP OFF
(VOLTAGE LOOP)
RLED = OFF
GLED = ON
DONE
CHARGER OFF
RLED = OFF
GLED = ON
Maxim Integrated
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
MAX1501Z ONLY
OFF
ACOK = HIGH
CHARGER OFF
ACOK = LOW
RLED = OFF
GLED = OFF
ACOK = (4.5V < VIN < 6.5V) AND (VIN > VBATT)
ACOK = LOW
CHGEN = LOW
VBATT < 2.8V
CHGEN = HIGH
MODE = LOW
NOBATT
DISABLE
PREQUAL
CHARGER OFF
ACOK = LOW
RLED = OFF
GLED = OFF
CHGEN = LOW
SOFT-START
CHGEN = HIGH
MODE = HIGH
SOFT-START
FAST CHARGE
(THERMALLY PROTECTED)
100% SETI CURRENT
ACOK = LOW
RLED = ON
GLED = OFF
TOP OFF
(VOLTAGE LOOP)
RLED = OFF
GLED = ON
Detailed Description
Modes of Operation
CHGEN and MODE together set the operating modes
of the MAX1501. Both inputs possess internal 175k
pulldown resistors to GND. Table 1 describes the four
operating modes of the MAX1501.
10
MODE
MODE
Disable Mode
No-Battery Mode
Maxim Integrated
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
Table 2. Battery Regulation Voltage
SELV
CHARGING MODE
GND
VL
Li+
4.1V
4.2V
NiMH/NiCd
4.5V
4.95V
REGULATION VOLTAGE
PREQUALIFICATION
FAST CHARGING
TOP-OFF
DONE
FAST-CHARGE CURRENT
BATTERY
CURRENT
RLED TURNS OFF AND GLED
TURNS ON WHEN CHARGE CURRENT
DROPS TO VALUE SET BY FULLI
(10%, 20%, OR 30% OF FASTCHARGE CURRENT).
BATTERY
VOLTAGE
MINIMUM CHARGE VOLTAGE
(2.8V)
CHARGE
TERMINATED
MAX1501Z
10% OF FAST-CHARGE CURRENT
tPREQUAL
tMAX
MAX1501
11
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
Table 3. RLED and GLED Behavior
MODE
Li+ Mode or
NiMH/NiCd Mode
STATE
10% current-limited precharge
Current-limited charge
Voltage-limited charge before top-off
Temperature-limited charge before top-off
Voltage-limited charge after top-off
Safety timer expires (MAX1501 only)
RLED
GLED
Sinks 10mA
High impedance
High impedance
Sinks 20mA
Disable Mode
High impedance
High impedance
No Battery Mode
High impedance
High impedance
No-Battery Mode
Connect CHGEN and MODE to VL to place the MAX1501
in no-battery mode. An external load can be connected to
BATT in this mode. VBATT regulates to 4V in no-battery
mode, regardless of the state of SELV.
The current-control loop, voltage-control loop, and
thermal-control loop all function in no-battery mode.
The loop gain of the voltage-control loop decreases to
ensure stability with no battery present. Connect a 10F
ceramic capacitor to BATT for stability. RLED and
GLED are both high impedance in no-battery mode.
ACOK
The ACOK output asserts low when VIN is present, 4.2V
VIN 6.25V, and VIN - VBATT > 100mV. The ACOK
open-drain output requires an external 100k pullup
12
Soft-Start
A ten-step, soft-start algorithm activates when entering
fast-charge mode. The charging current ramps up in
10% increments, 20ms per step, to the full charging
current when VBATT exceeds 2.8V.
Applications Information
Charge-Current Selection
Program the charging current using an external resistor
between SETI and GND. Set the charge-current resistor
with the following equation:
RSETI = 1000
1.4V
IBATT
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
Thermal-Regulation Selection
Set the regulated die temperature of the MAX1501 with
the TEMP three-level logic input. The MAX1501
reduces the charge current to limit the die temperature
to the value set by TEMP. The MAX1501 operates normally while the thermal loop is active. An active thermal
loop does not indicate a fault condition. TEMP allows
the MAX1501 to maximize the charge current while providing protection against excessive power dissipation.
Connect TEMP to GND to regulate the die temperature
at +95C. Leave TEMP floating to regulate the die temperature at +115C. Connect TEMP to VL to regulate
the die temperature at +135C.
Top-Off-Current Selection
Set the top-off-current threshold in the Li+ and
NiMH/NiCd charge modes with the FULLI three-level
logic input. The top-off-current threshold determines
when RLED turns off and GLED turns on, indicating the
charge status of the battery.
Connect FULLI to GND to set the top-off-current threshold to 10% of the fast-charge current. Connect FULLI to
VL to set the top-off-current threshold to 20% of the
fast-charge current. Leave FULLI floating to set the topoff-current threshold to 30% of the fast-charge current.
AC
ADAPTER
4.5V TO 6.5V
Capacitor Selection
Connect a ceramic capacitor from BATT to GND for
proper stability. Use a 10F X5R ceramic capacitor for
most applications.
Connect IN and INP together and bypass to GND with
a 1F ceramic capacitor. Use a larger input bypass
capacitor for high input voltages or high charging currents to reduce supply noise.
Thermal Considerations
The MAX1501 is available in a thermally enhanced thin
QFN package with exposed paddle. Connect the
exposed paddle of the MAX1501 to a large copper
ground plane to provide a thermal contact between the
device and the circuit board. The exposed paddle
transfers heat away from the device, allowing the
MAX1501 to charge the battery with maximum current,
while minimizing the increase in die temperature.
Application Circuits
Figure 5 shows the MAX1501 as a stand-alone Li+ battery charger. The 2.8k resistor connected to SETI sets
a charging current of 500mA.
Figure 6 shows the MAX1501 as a P-based Li+ battery
charger. Drive CHGEN low to charge the battery. Drive
CHGEN high to disable the charger. Connect a 100k
pullup resistor from ACOK to the logic supply voltage of
the P to detect the presence of an input supply. The
logic supply voltage must be less than 5.5V.
1F
BATT
10F
INP
AC
ADAPTER
4.5V TO 6.5V
1F
BATT
10F
INP
MAX1501/MAX1501Z
MAX1501/MAX1501Z
GLED
MODE
RLED
CHGEN
GLED
TMAX/I.C.
VI/O
ACOK
VL
TEMP
SELV
FULLI
ACOK
VL
CHGEN
SELV
SETI
SETI
GND
GND
TEMP
RPULLUP
FULLI
2.8k
TMAX/I.C.
RLED
2.8k
MODE
GND
GND
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
AC
ADAPTER
4.75V TO 6.5V
IN
1F
BATT
10F
INP
AC
ADAPTER
IN
1F
TEMP
RLED
ACOK
TMAX/I.C.
FULLI
SETI
SELV
GLED
TMAX/I.C.
RLED
VI/O
TEMP
RPULLUP
FULLI
ACOK
VL
CHGEN
MODE
CHGEN GND
10F
MAX1501/MAX1501Z
VL
2.8k
BATT
INP
MAX1501/MAX1501Z
GLED
4.95V
3-CELL NiMH
OR NiCd
5.25V TO 6.5V
SELV
MODE
SETI
GND
2.8k
GND
GND
AC
ADAPTER
4.75V TO 6.5V
IN
1F
BATT
10F
INP
4.5V TO 6.5V
MAX1501/MAX1501Z
1F
4V
IN
BATT
INP
GLED
GLED
RLED
RLED
VI/O
MAX1501/MAX1501Z
100k
FULLI
TMAX/I.C.
CHGEN
2.8k
VL
VL
ACOK
P
10F
MODE
SELV
SETI
TEMP
GND
GND
FULLI
CHGEN
TEMP
MODE
ON
OFF
TMAX/I.C.
ACOK
SELV
SETI
CURRENT-LIMIT
ADJUST
GND
GND
UP TO 1.4A
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
5V
3k
4.1k
5.1k
200k
3k
IN
100k
MAX1501/MAX1501Z
CHGEN
1k
5V
2.24k
GND
3k
100k
RT = 10k
AT +25C
10k
3.66k
1k
TBATT
RT
0C
27.28k
+25C
+50C
10.00k
4.16k
INP
IN
GND
SETI
GLED
RLED
SELV
GND
Pin Configuration
Figure 11 shows a circuit that adds temperature protection to the battery. Install the thermistor as close to the
battery as possible to ensure accurate temperature measurement. The output of this circuit is logic high when the
battery temperature is less than 0C and greater than
+50C. Driving CHGEN high disables the charger.
16
15
14
13
12 BATT
Chip Information
11 ACOK
MAX1501/
MAX1501Z
10 CHGEN
**EXPOSED PADDLE
8
TEMP
FULLI
VL
TMAX/I.C.
MODE
5mm x 5mm
THIN QFN
**CONNECT EXPOSED PADDLE TO GND
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a
+, #, or - in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but the
drawing pertains to the package regardless of RoHS status.
Maxim Integrated
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE NO.
LAND
PATTERN NO.
16 TQFN
T1655+3
21-0140
90-0073
15
MAX1501
Highly Integrated, Linear Battery Charger with
Thermal Regulation for Portable Applications
Revision History
REVISION
NUMBER
REVISION
DATE
4/14
DESCRIPTION
Updated General Description, NiMH/NiCd Charge Mode, and Application Circuits
sections
PAGES
CHANGED
1, 11, 12,
14, 16
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
16 ________________________________Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
2014 Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.