D EUTSCHE NORM
Chemical composition
17744
Supersedes
February 1983 edition.
ICS 77.120.40
Nickelknetlegierungen mit Molybdn und Chrom
Zusammensetzung
In keeping with current practice in standards published by the International Organization for Standardization
(ISO), a comma has been used throughout as the decimal marker.
Contents
Page
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Chemical composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Forms supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Chemical analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Rounding of results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other relevant standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
2
2
2
2
2
5
Foreword
This standard has been prepared by the Normenausschuss Nichteisenmetalle (Nonferrous Metals Standards
Committee), Technical Committee Nickelwerkstoffe.
See Other relevant standards for further standards covering the composition of nickel alloys.
Amendments
This standard differs from the February 1983 edition in that it has been revised in form and substance (with
the chemical composition being updated), two grades have been dropped and 13 grades have been included.
Previous editions
DIN 17744: 1973-01, 1983-02.
Scope
This standard specifies the chemical composition of wrought nickel-chromium-molybdenum alloys as used
for semi-finished products and provides information about the forms normally supplied.
Continued on pages 2 to 5.
Translation by DIN-Sprachendienst.
In case of doubt, the German-language original should be consulted as the authoritative text.
Page 2
DIN 17744 : 2002-09
Normative references
This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the titles of the publications are listed below.
For dated references, subsequent amendments to or revisions of any of these publications apply to this
standard only when incorporated in it by amendment or revision. For undated references, the latest edition of
the publication referred to applies.
DIN 17750
DIN 17751
DIN 17752
DIN 17753
DIN EN 10095
ISO 31-0 : 1992
Nickel and wrought nickel alloy sheet, plate and strip Requirements and testing
Nickel and wrought nickel alloy pipes and tubes Requirements and testing
Nickel and wrought nickel alloy bars and rod Requirements and testing
Nickel and wrought nickel alloy wire Requirements and testing
Heat resisting steels and nickel alloys
Quantities and units Part 0: General principles
Designation
Wrought nickel-chromium-molybdenum alloys shall be designated using either the name of the grade or its
material number.
EXAMPLE:
Designation of a grade NiMo28 nickel alloy (material number: 2.4617):
Chemical composition
Forms supplied
Wrought nickel-chromium-molybdenum alloys may be supplied in the forms specified in table 2, with the semifinished products conforming to DIN 17750 (sheet, plate and strip), DIN 17751 (pipes and tubes), DIN 17752
(bars and rod), or DIN 17753 (wire).
Chemical analysis
The analytical method used to establish the chemical composition shall be at the manufacturers discretion. In
cases of doubt, the latest method is to be used.
When expressing the result, the rules given in clause 7 are to be followed.
Rounding of results
Rounding of results obtained from the chemical analysis (by measurement or calculation) shall be based on
Annex B of ISO 31-0. Rounding shall be carried out in a single stage to the same number of places as is given
in table 1.
The following rules are to be complied with:
a) if the figure after the last decimal place to which the value is to be expressed is less than 5, this figure
shall be deleted;
b) if the figure after the last decimal place to which the value is to be expressed is 5 or higher, the figure is
to be deleted and the last decimal place shall be increased by 1.
--`,,,`-`-`,,`,,`,`,,`---
--`,,,`-`-`,,`,,`,`,,`---
Material
number
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Other
Other
Other
Other
Other
Other
Other
Other
Other
Other
Other
Other
Other
2)
2)
4)
2)
1)
3)
Name
Nickel grade
Other
Other
Other
Other
Percentages by mass
2)
2)
Approx.
density in
g/cm3 1)
Page 3
DIN 17744 : 2002-09
Page 4
DIN 17744 : 2002-09
Table 2: Forms of nickel alloys supplied
Nickel grade
Name
Material
number
Application
Strip
Sheet,
plate
Pipes,
tubes
Bars,
rod
Wire
Forgings
Corrosion-resistant
components
Highly heat-resistant
components
Corrosion-resistant
components
Highly heat-resistant
components
Corrosion-resistant
components
Highly heat-resistant
components
Corrosion-resistant
components
Highly heat-resistant
components
Corrosion-resistant
components
Heat and highly
corrosion-resistant
components
Corrosion-resistant
components
NOTE: There are no DIN Standards specifying the products marked (X). The properties of products marked X
are dealt with in the standards given in clause 5.
--`,,,`-`-`,,`,,`,`,,`---
Page 5
DIN 17744 : 2002-09
--`,,,`-`-`,,`,,`,`,,`---
DIN 17740
DIN 17741
DIN 17742
DIN 17743
DIN 17745