For MPR-e and MPR-1c, if the SW version of the existing network is anterior to R5.0.0, all new or repaired MPT-MC/HC/XP received with a SW Release 5.2.0 must be downgraded to the network SW Release using MCT / TCO R5.0.0.
This MCT must be first downloaded from OLCS server to a laptop, where the downgrade can be performed.
Configuration [1+0]
MPT-HC-HQAM to MSS
Optical
MPT-HC-HQAM to Ethernet
device Optical
CAT5e cable
data and DC
1AC015760006
CAT5e cable
data and DC
1AC015760006
MPTaccess
or EASv2 board
Maintenance port
MPT-MC specificities :
MSS-4/8
MSS-1/4/8
MSS-1c
MSS-O
XPIC cord
XPIC cord
Pigtail
RJ45/N
QMA
connector
Option 1
Fiber
Option 2
To any switch or router
MSS
Pigtail RJ45/N
MSS-1/4/8
CAT5e cable
data and DC
1AC015760006
No MPTaccess board
If PFoE port MSS-1/4/8/1c + Pigtail
MPT
Access board
Pigtail
RJ45/N
Coaxial
Note :
Coupler 6, 7, 8 and 10,5 / 11 GHz
Fiber
Maintenance port
Power feed over Ethernet port
Coupler 11 to 38 GHz
Coupler
1+1 or 2+0 Copolar
Configuration [1+1]
MPT-MC / MPT-HC-HQAM to
MSS Electrical
MPT-HC-HQAM
MPT-XP-HQAM
MPT-MC
Coaxial
Fiber
MSS-1/4/8
Note: See the applicable MPR user manual
for other supported configurations.
CAT5e cable
data and DC
1AC015760006
RJ45 to any switch
or router
Pigtail
RJ45/N
Fiber
Max 4 MPT
Max 2 MPT
N connector
48 V DC
48 V DC
MPT1 pol V
MPT2 pol H
Pigtail
RJ45/N
XPIC cord
CAT5e cable
data and DC
1AC015760006
MSS-1/4/8
Note: See the applicable MPR user manual
for other supported configurations.
XPIC cord
Pigtail RJ45/N
Coaxial
Fiber
CAT5e cable
data and DC
1AC015760006
RJ45 to any
switch or router
Coaxial
48 V or
+24 V DC
48 V or
+24 V DC
MSS-1/4/8
Note: See the applicable MPR user manual
for other supported configurations.
Fiber
Max 2 MPT
Extended Power unit 3CC50174XXXX
Max 2 MPT
Extended Power unit 3CC50174XXXX
Connect the MPT grounding connector to the nearest grounding plate, using the ground cable
16mm 3CC08166AAXX. Washer, screw and lug are provided with the MPT.
6.2
6.1
Example :
11 to 38 GHz
coupler
5.2 Install and set MPT polarization, for high
frequency, turn the MPT polarization disk to be
aligned with the coupler waveguide. The connectors
must face down.
11.1
Note: This is a guideline for assembling the R2CT with the RJ45 connector for CAT5e cable. For details
see Best practice and tips MPR R2CT and RJ45 connector and grounding 3FQ 24013 1100 PCZZA.
8.1 Prepare the R2CT connector, insert the CAT5e cable, and insert the RJ45 plug unlocking clip.
Assembled R2CT
connector
R2CT connector
1AB150990002
11.3
8.2 Mount the RJ45 connector using the RJ45 hirose tool.
RJ45
connector
XPIC cable
RJ45 connector
1AB074610027
RPS cable
10
8.3 Hoist the cable using the buckle on the R2CT cap.
8.4 Connect the assembled R2CT to the MPT, mount another RJ45 plug indoors, and verify all cables
and connectors using a cable tester (to avoid short circuit and verify continuity).
9
Electrical
CAT5e
11
Pigtail RJ45/N
Fiber + SFP
Perform alignment
10
Coaxial
Measurement
1.2
1.1
Service kit cable VDC: 5 4.71 4.12 3.5 2.9 2.3 1.71 1.11 0.59 0.14
RSL (dBm) :
-10 -20 -30 -40 -50 -60 -70 -80 -90 -100
1.4
Contact
support
1 Contact
Support
1.3
Cat5e cable
1AB150990002