February 2007
PIP VEDV1003
Vessel Drawing/Data Sheet and Instructions
PRINTING HISTORY
August 1997
Issued
November 1999
Complete Revision
February 2007
Complete Revision
Not printed with State funds
COMPLETE REVISION
February 2007
PIP VEDV1003
Vessel Drawing/Data Sheet and Instructions
Table of Contents
1. Introduction................................. 2
1.1 Purpose............................................ 2
1.2 Scope............................................... 2
2. References .................................. 2
2.1 Process Industry Practices .............. 2
2.2 Industry Codes and Standards ........ 2
Data Sheet
Pressure Vessels
Page 1 of 5
PIP VEDV1003
Vessel Drawing/Data Sheet and Instructions
1.
COMPLETE REVISION
February 2007
Introduction
1.1
Purpose
The purpose of this Practice is to provide instruction to designers for preparation of
the User supplied Vessel Drawing/Data Sheet. The Vessel Drawing/Data Sheet,
prepared in conjunction with PIP VECV1001, PIP VESV1002, and PIP VEFV1100,
completes a specification suitable for obtaining comprehensive bids and subsequent
purchase of pressure vessels.
1.2
Scope
This Practice identifies information to be placed on PIP VEDV1003 Pressure Vessels
Data Sheet.
2.
References
2.1
2.2
3.
3.2
Design Data
The preparer shall have pressure vessel design experience and shall ensure the work
is both accurate and complete. The preparer shall avoid supplying information that is
not needed.
3.2.1
Entering Text
All text placed on the Vessel Drawing/Data Sheet shall be of readable size
and quality and reproducible in reduced size.
Page 2 of 5
COMPLETE REVISION
PIP VEDV1003
Vessel Drawing/Data Sheet and Instructions
February 2007
3.2.2
Entering Data
Each numbered line of the Vessel Drawing/Data Sheet shall be
(1) properly filled in or (2) marked NA (Not Applicable). Leave lines
blank if the information is not known at the time. Lines not completed
indicate that the form is not complete. These lines shall be completed by
designer or manufacturer.
3.2.3
Additional Data
Any additional information can be added in the Notes area of the Vessel
Drawing/Data Sheet. Otherwise, equipment supplier information shall be
forwarded to the vessel manufacturer (e.g., nozzle loading of agitators).
3.3
Drawing Views
Drawing views in general shall be orthographic and include Plan and
Elevation for vertical vessels and Elevation and End or Elevation and
Plan for horizontal vessels. Other views may be added.
3.3.2
Drafting Practices
Drafting practices shall be consistent with the following items:
a. Drawings shall be made to scale. If not to scale, the approximate
proportion shall be maintained.
b. Clearly identify bottom views, and only use them to describe complex
geometry.
c. North arrow is to be pointing upward on the drawing.
d. 0 degrees orientation shall be plant or unit north, whichever applies.
e. Component thickness, head/shell notations, etc., are optional.
f. Establish a reference line for tail dimensions. Use a head tangent line or
face of flange if vessel has a flanged end.
g. Show supports.
h. Show location of legs, lugs, clips, etc.
i. Identify and locate needed internal attachment details. Provide only
enough detail to describe the item or provide reference to a PIP
Standard Detail. See PIP VEFV1100.
Page 3 of 5
PIP VEDV1003
Vessel Drawing/Data Sheet and Instructions
COMPLETE REVISION
February 2007
Connection Schedule
The Connection Schedule is located on the Vessel Drawing/Data Sheet.
a. Mark: Enter the identification of the opening in this column. Use N
for nozzle, C for coupling, M for manway, and SO for skirt
opening. The format is N-1, N-2, etc.
Note: Multiple openings with identical descriptions (e.g., level
gauges) may have the same identification by adding a letter
suffix. The format is N-1 with the quantity given in the
No. Reqd column, and shown on the drawing as N-1A,
N-1B, etc.
b. No. Reqd: Enter the quantity of openings that will have a common
mark as described in (a).
c. Size: Enter the NPS (nominal pipe size) of the opening.
d. Class: Enter the ASME/ANSI flange class. For ASME B16.47 specify
Series A or B.
e. Facing: Enter the flange facing (e.g., RF, FF, RJ, etc.).
f. Center Line Projection: Enter the dimension from the centerline of the
vessel to the face of the flange, or enter the dimension from the
reference line to face of flange for head openings.
g. Description: Enter identification of service for the opening. Include
blind flanges and covers to be furnished with the vessel.
4.
Engineering Requirements
Complete this section with the all the specific design information for the particular
vessel that is being procured.
Page 4 of 5
COMPLETE REVISION
February 2007
4.2
PIP VEDV1003
Vessel Drawing/Data Sheet and Instructions
4.3
Summary of References
All applicable reference documents that apply to this particular vessel are to be
identified in this section.
4.4
Materials
All applicable material designations are to be listed for each vessel component using
the corresponding ASME specification and UNS number.
4.5
Nozzle Schedule
All nozzles connections are to be identified in this section as described in
Section 3.3.3.
4.6
Sketch
This section is to include a graphical representation of the outline of the vessel and
any associated details with dimensions of specific vessel components not given in the
reference documents.
Page 5 of 5
Issued for:
Proposal
DATA SHEET
VEDV1003-D
PRESSURE VESSELS
PAGE 1 OF 6
FEBRUARY 2007
Purchase
Facility Name/Location:
Item Name:
Item Tag No.:
Service:
Unit:
P&ID No.:
As Built Date:
Purchaser/Location:
Job No:
Requistion No:
Purchaser Order No.:
Manuf./Location:
Manuf. Order/Serial Nos:
A. ENGINEERING REQUIREMENTS
1. Design Pressure-Internal: Vessel:
psig @
F Jacket:
psig @
F
Coil:
psig @
F
2. Design Pressure-External: Vessel:
psi @
F Jacket:
psi @
F
Coil:
psi @
F
3. Minimum Design Metal Temperature, Vessel:
F @
psig Jacket:
F @
psig
Coil:
F @
psig.
Low Temperature Due to: Low Ambient
, Process Excursion , Normal Process Conditions .
4. Design Specific Gravity of Fluid: Vessel:
Jacket:
Coil:
.
5. MAWP Basis: Calculated , Same as Design .
6. Construction Code: ASME Section VIII, Division 1, Edition
, Addenda
Including Stamping.
Code Special Marking:
Lethal Service: ____, Code Case(s):
.
Special Service Requirements:
. Registration: National Board
(Required for U or U2 Stamps)
7. Vessel Position: ____________ Maximum Liquid Level in the Vessel in the Installed Position:
ft.
8. Vessel Size: Capacity:
Gallons
Inside Diameter:
ft Tangent Length:
ft.
9. Corrosion allowance, in: Vessel Internal:
, External:
, Nozzles:
, Internals:
.
Jacket Internal:
, External:
, Coil:
Supports:
, External Attachments:
.
For Non-Corrosive Service: ____
Seal Weld Internal Parts to Pressure Boundary: ____.
10. High Cyclic Service per Code
Cycles per Life of Unit: Vessel:
Jacket:
Coil:
.
Design Life:
Years Fatigue Analysis/Evaluation by Manufacturer: ____.
11. Welded Pressure Joint Requirements: Vessel: _____________, Jacket: _____________, Coil: _____________.
12. Post Weld Heat Treatment: _________________ Specification:
.
13. Wind Design: ASCE 7
Classification Category: ____ Basic Wind Speed:
mph.
Exposure Category: __________ Topographic Factor:
Elevation above Grade:
ft.
14. Seismic Design: ASCE 7
Soil Profile Classification: __ Aa:
Av:
, R:
.
15. Other Loadings:
.
16. Shell Thickness, in: Vessel:
Jacket:
Coil:
.
17. Head Thickness (Minimum after Forming), in: Vessel:
Jacket:
.
18. Type of Heads: Top/Ends: _____________
Bottom: ____________
.
19.
20.
21.
22.
23.
24.
25.
26.
No.
Description
By
Check.
App.
B.
1.
2.
3.
4.
5.
6.
7.
C.
DATA SHEET
VEDV1003-D
PRESSURE VESSELS
PAGE 2 OF 6
FEBRUARY 2007
PIP
Practice
No.
Check If
Applicable
Title
PIP &
Other
Standards
Check If
Applicable
Title
VECV1001
VEFV1116
VESV1002
VEFV1117
VEFV1101
VEFV1102
VEFV1103
VEFV1118
VEFV1119
Type ___
VEFV1120
Type ___
VEFV1104
VEFV1121
Type ___
VEFV1122
VEFV1105
VEFV1106
VEFV1107
VEFV1108
VEFV1109
VEFV1110
VEFV1111
VEFV1112
VEFV1113
VEFV1114
VEFV1115
VEFV1124
VEFV1125
VEFV1128
Type ___
VEFV1129
STF05520
VEFV1123
STF05521
STF05535
STF05501
DATA SHEET
VEDV1003-D
PRESSURE VESSELS
PAGE 3 OF 6
FEBRUARY 2007
D. MATERIALS
All materials must be specified in accordance with ASME Pressure Vessel Code.
Material
1.
2.
3.
4.
5.
Shell
Jacket
Heads
Reinforcing Pads
Nozzle Necks: Jacket
Shell
6. Nozzle Flanges: Jacket
Shell
7. Manhole Neck
8. Manhole Flange and Cover
9. Internal Bolting: Bolts
Nuts
10. External Bolting: Bolts
Nuts
11. Gaskets: Vessel
Jacket
Coil
12. Supports: _______
_______
13. Lifting Lugs
14. Internals
15. Body Flanges
16. Jacket Closure Ring
17. Stiffening Rings
18. Insulation Rings
19. Coil
20. Lining
21. Special Requirements
Notes:
DATA SHEET
VEDV1003-D
PRESSURE VESSELS
PAGE 4 OF 6
FEBRUARY 2007
E. NOZZLE SCHEDULE
The Purchaser will orient and locate nozzles orientation on the Manufacturers approval drawings.
MARK
Notes:
NO.
REQD
SIZE
CLASS
TYPE
CL
PROJECTION
DESCRIPTION
DATA SHEET
VEDV1003-D
PRESSURE VESSELS
PAGE 5 OF 6
FEBRUARY 2007
F. SKETCH
Outlines of equipment and dimensions that Manufacturer must hold.
DATA SHEET
VEDV1003-D
PRESSURE VESSELS
PAGE 6 OF 6
FEBRUARY 2007