TECNICAS DE MECANISMOS DE
TRADUSCCION (NOVIEMBRE 2015)
Primero Ricardo Cisneros T, Profesor, UPVM , Segundo Ezra G Gutierrez A, Alumno, UPVM
I. INTRODUCCION
Ay varios ejemplos de micromaquinas traductores
mecanicos y el proposito de este articulo es presenter
algunos de los fundamentos, conceptos y tecnicas que son
usadas en el diseo de maquinas microsensores y
actuadores.Los mas importantes mecanismos como sensores
incluyendo los siguientes effectos: piezoresistividad,
piezoelectrico, capacitancia de variables, opticos, y tecnicas de
resonancia.De igual manera tambien exiten sensores
inteligentes llamados asi por su comportamiento ante
especificosefectos.
.
II. PIEZORESISTIVIDAD
Piezo signicando presion por lo tanto piezoresistividad es
un efecto exhibido por varios materiales que exiben un cambio
de resistividad cuando se le aplica una presion.Los efectos
fueron descubiertos por Lord Kelvin in 1856, quien noto que
This paragraph of the first footnote will contain the date on which you
submitted your paper for review. It will also contain support information,
including sponsor and financial support acknowledgment. For example, This
work was supported in part by the U.S. Department of Commerce under Grant
BS123456.
The next few paragraphs should contain the authors current affiliations,
including current address and e-mail. For example, F. A. Author is with the
National Institute of Standards and Technology, Boulder, CO 80305 USA (email: author@ boulder.nist.gov).
S. B. Author, Jr., was with Rice University, Houston, TX 77005 USA. He
is now with the Department of Physics, Colorado State University, Fort
Collins, CO 80523 USA (e-mail: author@lamar.colostate.edu).
T. C. Author is with the Electrical Engineering Department, University of
Colorado, Boulder, CO 80309 USA, on leave from the National Research
Institute for Metals, Tsukuba, Japan (e-mail: author@nrim.go.jp).
(1)
(2)
Donde R es la Resistencia inicial y la diferencia de R es el
cambio de Resistencia. Los terminus de L y su diferencial
estan definidos por la tensin aplicada denotada como e
(dimensin menos). Para todos los materiales elsticos, existe
una relacin entre el strees O (N/m2) y la tension e: es decir,
que obedecen la ley Hooke y por lo tanto deformar
linealmente con la fuerza aplicada. la constante de
(3)
Cuando un material elastic es sometido a una fuerza a lo largo
de su eje, tambin se deformar a lo largo de los ejes
ortogonales. Por ejemplo, si un bloque rectangular de un
material es estirado a lo largo su longuitud , anchura y espesor
disminuyen.En otras palabras, una deformacion por traccion a
lo largo de la longuitud dara lugar a la tension de compression
en las direcciones ortogonales.Tipicamente, los ejes y
tensiones tranversales seran diferentes y la proporcion entre
los dos es conocido como la razon poisson, (v), los efectos de
la rzon poisson se representan con la siguiente figura 4
III. PIEZOELECTRICIDAD
V. TECNICAS OPTICAS
Intensidad
Fase
Longitud de onda
Posicion especial
Frecuencia
Polarizacion
A. Intensidad
La intensidad o cantidad de energa por unidad de rea y
unidad de tiempo que transmite una onda electromagntica es
GRAFICA
VIII. CONCLUSIONES
APPENDIX
Appendixes, if needed, appear before the acknowledgment.
ACKNOWLEDGMENT
The preferred spelling of the word acknowledgment in
American English is without an e after the g. Use the
singular heading even if you have many acknowledgments.
Avoid expressions such as One of us (S.B.A.) would like to
thank ... . Instead, write F. A. Author thanks ... . In most
cases, sponsor and financial support acknowledgments are
placed in the unnumbered footnote on the first page, not here.
The two types of contents of that are published are; 1) peerreviewed and 2) archival. The Transactions and Journals
Department publishes scholarly articles of archival value as
well as tutorial expositions and critical reviews of classical
subjects and topics of current interest.
Authors should consider the following points:
1) Technical papers submitted for publication must advance
the state of knowledge and must cite relevant prior work.
2) The length of a submitted paper should be commensurate
with the importance, or appropriate to the complexity, of
the work. For example, an obvious extension of
REFERENCIAS
[1]
[2]