Section 1
ANS. ICON
21. When a wire is insulated with glass braid or asbestos and requires
stripping, which of the following tools should not be used?
ANS. HOT-BLADE WIRE STRIPPER
22. When you solder electrical connector splices, and terminal lugs, what
type of solder should you use?
ANS. 60/40 SOLDER
23. When noninsulated splices and terminal lugs are insulated, what types
insulation are most commonly used?
ANS. RUBBER TAPE AND HEAT SHRINKABLE TUBING
24. When a Western Union splice is used to connect two wires, why should
the twisted ends of the wires be pressed down as close as possible to the
straight portion of the wire?
ANS. TO PREVENT THE WIRES FROM PUNCTURING THE TAPE
COVERING
25. What types of insulation are best suited for use in a high-temperature
environment?
ANS. FEP, EXTRUDED POLYTETRAFLUOROETHYLENE AND SILICONE
RUBBER
26. What should be done with the removable tip of a soldering gun after it
becomes pitted?
ANS. FILE THE TIP SMOOTH AND RETIN IT
27. For a gyro to be universally mounted, it MUST have a total of how many
gimbals, if any?
ANS. TWO
28. A position servo system exhibits a series of over travels. This condition is
known by which of the following terms?
ANS. HUNTING
29. For a servo system to operate smoothly and efficiently, it must have
balance between which of the following factors?
51. When electrical and electronic components are soldered, what type of
flux must be used?
ANS. ROSIN
52. What is the most efficient soldering temperature?
ANS. 550F
53. The current gain in a common-collector circuit is called _____.
ANS. GAMMA
54. A method for checking transistor is cumbersome when more than one
transistor is bad in a circuit?
ANS. SUBSTITUTION METHOD
55. A breakdown theory that explains the action that take place in a heavily
doped PN-junction with a reverse bias of less than 5 volts.
ANS. ZENER EFFECT
56. The arrow in a MOSFET indicates a _____.
ANS. SUBSTRATE
76. Which of the following alloys will melt directly to liquid and have no
plastic or semiliquid state?
ANS. EUTECTIC ALLOY
77. A conformal coating is considered thin if it is less than what thickness?
ANS. 0.025 INCH
78. What maximum number of logic gates should be expected in a largescale integration circuit?
ANS. 2,000
79. Protective materials applied to electronic assemblies to prevent damage
caused by corrosion, moisture, and stress are called ________.
ANS. CONFORMAL COATINGS
80. Cutting and peeling is an easy method of removing which of the following
types of coatings?
ANS. SILICONE
81. What are the approved methods of conformal coating removal?
ANS. MECHANICAL, THERMAL & CHEMICAL
82. Turret, fork, and hook terminals are examples of what type of
termination?
ANS. ABOVE-THE-BOARD
83. What total number of degrees of bend are (a) fully clinched leads and (b)
semi-clinched leads?
ANS. (A) 90 (B) 45
84. Stirring the lead during desoldering prevents which of the following
unwanted results?
ANS. SWEAT JOINTS
85. Most damage to printed circuit boards occur at which of the following
times?
ANS. DURING COMPONENT REMOVAL
86. When removing solder with a solder wick, where should the wick be
placed in relation to the solder joint and the iron?
ANS. BETWEEN THE JOINT AND THE IRON
87. Visual inspection of a completed repair is conducted to evaluate which of
the following aspects of the repair?
ANS. WORKMANSHIP QUALITY
88. Plug-in DIPs are susceptible to loosening because of which of the
following causes?
ANS. VIBRATION
89. For the removal of imbedded TOs in which of the following are free, which
of the following methods is recommended?
ANS. PUSH OUT GENTLY
90. When a TO or a DIP is replaced on a printed circuit board, what type of
termination is normally used?
ANS. THROUGH-THE-BOARD
91. Heating the leads and lifting them up with tweezers is the preferred
method of removing which of the following components?
ANS. FLAT PACKS
92. What is the first step in the repair of burned or scorched boards?
ANS. REMOVING ALL DISCOLORED MATERIAL
93. The force between a magnet and a piece of ferromagnetic metal that has
not been magnetized:
ANS. IS NEVER REPULSIVE
94. What significant advantage, in some applications, of a toroidal coil over a
solenoid is:
116. The most popular op-amp packages are metal can, 8-pin DIP, and the
SMT. Which of these corresponds to TO-99?
ANS. METAL CAN
117. The minimum amount of current needed for an SCR to conduct
continuously.
ANS. HOLDING CURRENT
118. The voltage across the anode (A) and cathode (K) terminals of an SCR
when conducting.
ANS. HOLDING VOLTAGE
119. Confining each program to certain defined limits in memory is called
_____.
ANS. MEMORY PROTECTION
120. Transient suppression minimizes the chance of _____.
ANS. DIODE FAILURE
121. In OTA, transconductance is control by _____.
ANS. BIAS CURRENT
122. What inductor is used at frequency 95 MHz?
ANS. AIR CORE
123. Regulator that dissipates less power and less heat.
ANS. SWITCHING REGULATOR
124. oscilloscope
ANS. TRIGGER HOLD OFF
125. Set of programs that are between applications software and hardware.
ANS. OPERATING PROGRAM
135. What causes the process called junction recombination to occur when N
and P materials are joined together?
146. What current flow in a semiconductor is due to the applied electric field?
ANS. DRIFT CURRENT
147. The purpose of installing thyrectors.
ANS. TO PROTECT THE CIRCUITS FROM HIGH VOLTAGE SURGES
148. Confining each program to certain defined limits in memory is called
______.
ANS. MEMORY PROTECTION
149. Transient suppression minimizes the chance of _____.
ANS. DIODE FAILURE
150. In OTA transconductance is controlled by_____.
ANS. BIAS CURRENT
151. What inductor is used at frequencies of 95 MHZ.
ANS. AIR CORE
152. Regulator that dissipates less power and less heat.
ANS. SWITCHING REGULATOR
153. Period of time which the oscilloscope cannot trigger.
ANS. TRIGGER HOLD OFF
154. A good form of inductor at FM
ANS. AIR CORE
155. Set of programs that lies between application software and the
computer hardware.
ANS. OPERATING PROGRAM
156. Instrumentation amplifiers are used in_____.
ANS. HIGH NOISE ENVIRONMENT
157. What type of indicating device is usually installed in the stator circuit of
a torque synchro system.
ANS. AN OVERLOAD INDICATOR
158. ____ is the process of making a material passive in relation to another
material prior to using the material together.
ANS. PASSIVATION
159. In the context of corrosion, _____ is the spontaneous formation of a hard
non reactive surface film that inhibits further corrosion. This layer is usually
an oxide or nitride that is a few molecules thick.
ANS. PASSIVATION
160. Two conductors with insulator between them is called_____.
ANS. CONDENSER (OLD NAME)/ CAPACITOR (NEW NAME)
161. Chemical reactions that release energy are called exothermic reactions;
____ is an example of exothermic reaction.
ANS. FREEZING
162. This bridge is often used in laboratories to measure both capacitances
and inductive circuits at higher frequencies.
ANS. RADIO FREQUENCY BRIDGE
163. Is sometimes called Maxwell wien bridge and is used to measure an
unknown inductance with a standard capacitance.
ANS. MAXWELL BRIDGE
164. A four arm alternating current bridge used to measure self inductance in
terms of capacitance and resistance; bridge balance is independent of
frequency.
ANS. OWEN BRIDGE
165. A graph of the thermodynamic properties of moist air at a constant
pressure, such as wet bulb temperature and dry bulb temperature.
175. A filter which allows a narrow band of frequencies to pass through the
circuit and rejects or attenuates frequencies which are either higher or lower
than the desired frequency.
ANS. BANDPASS FILTER
176. A circuit that is used to block the passage of current for a narrow band
of frequencies, while allowing current to flow at all frequencies above or
below the this band. This type of filter is also known as a band suppression or
band reject.
ANS. BANDSTOP FILTER
177. What theorem is used in solving electrical circuits with several voltage
sources?
ANS. SUPERPOSITION
178. What is the process of determining the magnitude of something in
terms of a recognized standard?
ANS. MEASUREMENT
179. A variable positive regulator.
ANS. 317
180. What is the efficiency of a full wave rectifier?
ANS. 81.2%
181. The value at any instant of time.
ANS. INSTANTANEOUS VALUE
182. In carbon zinc battery, zinc serves as the _____.
ANS. NEGATIVE CATHODE
183. The electronic the electronic transfer from one stage to another is
called_____.
ANS. COUPLING
184. Who discovered the magnetic effect?
204. A paper capacitor generally has a shorter service life than most other
types of capacitor. This is a ____ statement.
ANS. FALSE
205. Voltage drop is____
ANS. DIFFERENCE IN POTENTIAL BETWEEN TWO POINT
206. The slip speed of an induction motor is 100% until the rotor moves and
then falls to a ____.
ANS. LOW VALUE
207. A relay can be used to_____.
ANS. DECREASE THE CURRENT IN A CIRCUIT
208. Flow calorimeters are classified by the type of measurement performed,
the type of heating used, and what other characteristic?
ANS. TYPE OF CIRCULATION USED
209. Capacitance of a variable capacitor is maximum at
ANS. MOVABLE PLATES ARE CLOSE TOGETHER
210. There is an attractive force between two parallel conductors when the
current in them is
ANS. OPPOSITE IN DIRECTION
211. The speed in a generator is doubled while the flux is constant the
generator EMF is
ANS. DOUBLE
212. Intrinsic semiconductor have
ANS. COVALENT BONDS FORMING A TETRAHEDRAL STRUCTURE
213. If you are preparing to single lace conductors, what total length must
the lacing be in a relationship be to the longest conductor
ANS. 2 AND ONE HALF TIMES THE LENGTH
214. What causes the process called junction recombination to occur when N
type and P type materials are joined together
ANS. DIFFUSION OF ELECTRONS AND HOLES MOVING ACROSS THE
JUNCTION IN THE TWO MATERIAL
215. At typical silicon wafer has approximately (a) what diameter and (b)
what thickness?
ANS. (A) 2 INCHES (B) 0.01-0 .02
216. Each satellite in the iridium satellite network has how many spot
beams?
ANS. 48
217. False regarding a three phase induction motor
ANS. THE SYNCHRONOUS SPEED IS INVERSELY PROPORTIONAL TO
THE NUMBER OF POLES
243. Materials that are engineered materials made from two or more
constituent materials made with significantly different physical or chemical
properties which remains separate and distinct on a macroscopic level within
the finished structure.
ANS. COMPOSITE MATERIAL
244. Vacuum evaporation and cathode sputtering are two methods used to
produce which of the following types of components
ANS. THIN FILM
245. Which of the following types of synchro devices provides a mechanical
output?
ANS. TORQUE RECEIVER
246. What is the most common range of value selected for a power supply
choke?
ANS. 1-20 HENRIES
247. An alternator using a gas turbine as a prime mover should have what
type of rotor?
ANS. TURBINE DRIVEN
248. Refers to the total opposition to current
ANS. IMPEDANCE
249. Which of the following is an advantage of using a current probe?
ANS. IT SENSES CURRENT BY INDUCTION WITHOUT BEING
CONNECTED DIRECTLY INTO THE CIRCUIT
250. If the flux per pole of an AC generator is increased, the speed
ANS. DECREASES
251. The number of pole pairs required to established a rotating magnetic
field in a multiphase motor stator is determined by which of the following
factors?
ANS. THE NUMBER OF PHASES
283. A brushless, synchronous electric motor that can divide a full rotation
into a large number of steps.
ANS. STEPPER MOTOR
284. A method of curve fitting using linear polynomials heavily employed in
mathematics particularly numerical analysis and numerous application
computer graphics.
ANS. LINEAR INTERPOLATION
285. The simplest of all gas filled radiation detectors, and is used for the
detection or measurement of ionization radiation.
ANS. IONIZATION CHAMBER
286. The semiconductor doping impurities arsenic, antimony, and bismuth
are classified as what type of impurities?
ANS. PENTAVALENT