Refer to the exhibit. Which set of commands will configure static routes that will allow the
WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other
traffic to the Internet?
What are two possible reasons for this result? (Choose two.)
The Marshall and Fiji routers have been correctly configured to use RIP v1 as a dynamic
routing protocol, and all interfaces on the Marshall and Fiji routers are reporting "interface is
up, line protocol is up" status. RIP v1 is then configured on the Chatham router using the
following commands:
If no additional routing is configured on Chatham, Marshall, or Fiji, what will be the result?
5 Which router component stores the information that is displayed by the show arp command?
• flash
• NVRAM
• RAM
• ROM
Router A is directly connected to the networks shown in the graphic and has a default route
that points to Router B. All interfaces are active and properly addressed. However, when the
workstation on network 172.16.4.0/24 sends a packet to destination address 172.16.201.5, it is
discarded by Router A. What can be a reason for this result?
What can be determined from the output shown in the exhibit? (Choose two.)
• Annapolis is a 2611 router that is connected to the S0/0 interface of the Montgomery
router.
• All of the routers are connected to Montgomery through an Ethernet switch.
• Montgomery has Layer 2 connectivity with Cumberland.
• Layer 3 connectivity is operational for all of the devices listed in the Device ID
column.
• An administrator consoled into the Waldorf router can ping the Brant router.
• Brant, Fisherman, and Potomac are directly connected to Montgomery.
10 If a PC does not have network connectivity to a router, which router port can be used to
establish communication?
• console
• Ethernet
• serial
• VTY
11
Which two conclusions can be validly derived from the set of commands shown in the
exhibit? (Choose two.)
• Host 10.128.114.76 will be able to establish a Telnet session with host 172.25.0.26
• Host 10.128.114.76 will not be able to establish an FTP session with available hosts
on the 172.25.0.0 network.
• Host 192.168.85.76 will be able to establish a Telnet session with host 172.25.0.26.
• Host 192.168.85.76 will be able to establish an FTP session with available hosts on
the 172.25.0.0 network.
• Host 172.25.0.26 will not be able to establish a Telnet session with available hosts
on the 192.168.85.0 network.
• No host will be able to access IP services on the 10.128.114.0 network.
What two pieces of information can be obtained from the output? (Choose two.)
15 What are two possible reasons a router would not load a valid IOS from flash? (Choose
two.)
16
What two facts can be determined from the output shown in the exhibit? (Choose two.)
The following access list has been created to prevent traffic from host 172.23.40.36 from
accessing the 192.168.34.0 network.
Refer to the graphic. Which group of commands will properly place the access list so that the
host is denied access only to network 192.168.34.0?
Refer to the exhibit. Communication is needed between the Marketing LAN and the Sales
LAN. All hosts on those LANs also need connectivity to the Internet. Which three commands
will allow this communication? (Choose three).
Refer to the exhibit. Router C interface E0 has gone down. What is the maximum time that
will elapse before Router A learns that network 110.90.1.0 is down?
• 5 seconds
• 13 seconds
• 17 seconds
• 25 seconds
• 30 seconds
• 90 seconds
• Paste the IOS filename to the command line of the router while in global configuration
mode. Press enter. Then issue the copy tftp flash command.
• Use the setup utility to load the new image to flash.
• Copy the IOS image file from a TFTP server using the command copyfilenameip
addressflash .
• Copy the IOS image file from a TFTP server using the command copy tftp flash.
When prompted, provide the IP address or name of the TFTP server and the IOS
image filename.
24 In what order will the initial startup routine of a router locate and load the IOS if the
config-register setting is 0x2102 and there are no boot system commands present in the
startup-config file?
25 What are the results of setting the boot field bits in the configuration register to "0000"?
(Choose two.)
Which devices can be used to convert the data from a WAN router at the customer site into a
form acceptable for use by the WAN service provider? (Choose three.)
• Ethernet switch
• DTE
• modem
• hub
• DCE device
• CSU/DSU
27
Refer to the exhibit. While planning an IOS upgrade, the administrator issues the command
show version. What is the current IOS boot location?
• RAM
• NVRAM
• flash
• ROM
28 Why are interface descriptions used in router configurations? (Choose three).
• to enable support personnel to easily identify networks and customers that may
be affected by a possible interface issue
• to provide comments on the interface without affecting the router functionality
• to display access warning messages before users enter the interface configuration
mode
• to eliminate the need to use IP addresses when using the ping and telnet commands
• to identify the purpose and location of the interface
29 What are two characteristics of the support for Telnet within Cisco IOS software? (Choose
two.)
• Up to five separate Telnet lines are supported by default in standard edition IOS
files.
• For security purposes, Telnet sessions are required to be established from the
privileged mode.
• A router can host simultaneous Telnet sessions.
• Once established, a Telnet session can remain operational regardless of network status.
• Telnet tests wireless connectivity and does not require a physical connection between
devices to gain remote access.
30
A network administrator has enabled RIP on routers A and B in the network diagram. Which
commands will prevent RIP v1 updates from being sent to Router C?
31 What information can be learned during the initial router bootup? (Choose two.)
• RIP
• EIGRP
• OSPF
• IGP
• BGP
33 The following access list has been correctly applied to a router interface:
Which of the following statements are true about this ACL? (Choose three.)
• This is an invalid ACL because the wildcard mask is missing from the command.
• A wildcard mask of 0.0.0.0 is assumed for 172.30.65.52.
• This is an extended IP access list.
• All traffic from 172.30.65.51 will be permitted.
• This is a standard IP access list.
Assuming this ACL is correctly applied to a router interface, which statements describe traffic
on the network? (Choose two.)
Refer to the graphic. Which command will create a standard ACL that will apply to outbound
traffic on interface Fa0/0 of router A and will deny IP traffic from any host on network
172.16.34.0/24 that is destined for network 192.168.5.0/24 while allowing all other IP traffic?
• RAM
• NVRAM
• IOS
• IP Address
• TFTP
• FLASH
38
Which ACL can be applied in the outbound direction of Serial 0/0 on router B in the graphic
to allow all IP traffic from LAN A to the Internet, allow Web traffic from LAN B to the
Internet, and deny all other traffic to the Internet?
39
What will occur when the following ACL is applied inbound to both FastEthernet interfaces
of the Anaheim Router shown in the exhibit?
• The ACL will deny all traffic because of the implied deny ip any any statement at the
end of the ACL.
• The ACL will have no effect because it should be applied in the outbound direction on
the FastEthernet interfaces.
• The Finance Admin host and the HR Admin host will be able to ping to each other.
All other traffic will be denied.
• The Finance Admin host and the HR Admin host will be able to ping to each
other. The HR Admin host will be allowed to access Web servers on the Internet,
while the Finance Admin host will be denied Internet Web access.
40 Which of the following statements are true regarding routed protocols? (Choose two.)
Refer to the graphic. A network administrator has a console connection to Router A. Pings to
Router B are successful, but pings to Routers C and D fail. What is the first step in
troubleshooting the problem?
• Use the show cdp neighbors detail command from router A to gather information
about all Cisco routers in the network.
• Use the traceroute command to discover exactly which link in the network is down.
• Use an extended ping from router A to each router in the network.
• Use the show interfaces command from a Telnet session on router B to check the
connection to router C.
Erasing the nvram filesystem will remove all files! Continue? [Confirm]
[OK]
Erase of nvram: complete
If the router unexpectedly loses power after this sequence, what will occur when power is
restored?
• The router will enter ROM monitor mode upon completion of the power-on self test
(POST).
• The router will load the last known valid configuration file.
• The router will enter Rx-boot mode.
• The router will prompt the user to enter setup mode or to continue without
entering setup mode.
43 Which two steps describe how to create a functional physical connection between a router
console and a terminal? (Choose two.)
• Use a crossover cable to connect the terminal serial port to the router console port.
• Use a rollover cable to connect the terminal NIC to the router console port.
• Use an RJ-45 to DB-9 adapter on the terminal serial port to connect to the cable
going to the router console.
• Use a transceiver to connect a straight-through cable to the router console port.
• Use a straight-through cable to connect the router console port to the terminal NIC.
• Use a rollover cable to connect from a terminal serial port to the router console
port.
44
Why would an administrator change the value highlighted in the exhibit? (Choose two.)
• packet switching
• microsegmentation
• domain name resolution
• path selection
• flow control
47 Which commands will show the status and IP address of all interfaces on a router?
(Choose two.)
• show protocols
• show ip protocols
• show version
• show interfaces
• show ip ports
48
Neither router in the graphic has a host table or DNS available. The interfaces and passwords
have been correctly configured. Which of the following commands will initiate a Telnet
session? (Choose two.)