com
978 997 4104
sales@smarterglass.com
CPT TFT-LCD
CLAA 201WA04
APPROVED BY
JOY CHOU
CHECKED BY
Tristan
PREPARED BY
Product Planning
Management
General Division
Doc. No:
CLAA201WA04- SPEC
Issue Date:
2007/07/04
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Table Of Content
NO
1
2
3
4
5
6
7
8
9
10
11
12
Table of Content
OVERVIEW
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
INTERFACE PIN CONNECTION
INTERFACE TIMING
BLOCK DIAGRAM
MECHANICAL SPECIFICATION
OPTICAL CHARACTERISTICS
RELIABILITY TEST CONDITIONS
PACKING SPECIFICATION
DESIGNATION OF LOT MARK
HANDLING PRECAUTIONS FOR TFT-LCD MODULE
Note
P.4
P.5
P.7
P.12
P.14
P.17
P.18
P.20
P.23
P.25
P.27
P.29
Page: 2/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
1.OVERVIEW
CLAA201WA04 is 20.1(51.11cm) color TFT-LCD (Thin Film Transistor Liquid Crystal Display)
module composed of LCD panel, LVDS driver ICs, control circuit and backlight(CCFL, 4 tubes). By
applying 8 bit digital data (6bits+Hi-FRC), 16801050, drived by 5 voltages,16.7M-color images are
displayed on the 20.1 diagonal screen. The module structure is fixed by iron frame,without the inverter
for the backlight. Interface of data and control signals is typ.General specification are summarized in the
following table:
ITEM
Display Area(mm)
Number of Pixels
Pixel Pitch(mm)
Color Pixel Arrangement
Display Mode
Number of Colors
Brightness(cd/m^2)
Viewing Angle(H/V)
Surface Treatment
Power consumption(W)
Module Size(mm)
Module Weight(g)
Backlight Unit
SPECIFICATION
433.44 (H) 270.9 (V) (20.1-inch diagonal)
1680 (H) 1050(V)
0.258(H) 0.258(V)
RGB vertical stripe
NormallyWhite, TN
16.7M(6bits+Hi-FRC)
300cd/m2 (Typ.)(center, 7.5mA)
170/160 (Typ.)
Anti-glare, 3H
34.0(Typ.) (w/o Inverter)
459.4(W) 296.4(H) 16.6 (D) (Typ.)
2850(Typ)
CCFL, 4 tubes(top 2/bottom 2) , Edge light
Page: 3/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
SYMBOL
VCC
MIN.
0
MAX.
6.5
UNIT
V
Remark
--
Lamp Voltage
VL
770
970
Vrms
--
Lamp Current
ILO
mArms
*4). 7)
FL
VESDt
VESDc
Top
Tstg
40
-200
-8000
0
-20
--
80
200
8000
50
60
1
kHz
V
V
--
Lamp Frequency
Electrostatic Voltage
Operation Temperature (Surrounding)
Storage Temperature
*5)
*1). 2). 3). 6)
*1). 2). 3)
sec
*8)
TD
Delayed Discharge Time
[Note]
*1) The relative temperature and humidity range are as below sketch, 90%RHMax. (Ta40)
*2) The maximum wet bulb temperature 39(Ta40) and without dewing.
*3) If you use the product in a environment which over the definition of temperature and humidity
too long to effect the result of eye-atching.
*4) Product life-time related to lamp current, pls operate the production follow statement at page 9
CN2, 4 (BACKLIGHT)
*5) The testing conditions are according to IEC 1000-4-2 specification
VESDtBy using contact-mode to discharge each pin of the connector.
VESDcBy using contact-mode to discharge the module.
*6) If you operate the product in normal temperature range, the center surface of panel should be
under 60.
Humidity85%RH without condensation.
Relative Humidity 90% (Ta 40)
Wet Bulb Temperature 39(Ta40)
*7) When lamp current over the definition of absolute maximun, product life-time will decay rapidly
or operate unusual. If lamp current is under 3.0mA, the lamp could be abnormal-starting.
If for special request testing,then the minimun value of current is 2mA.It is not to promise
product life-time and lighting in normally situation.
*8) Delayed discharge time test condition:
Starting lamp voltage = 1700 Vrms
Before test TD, lamp should operate at least 1min. , and lamp current should follow typical
lamp current specification. To place panel at room temp. (25+/- 2) below for 24hr, and then to
measure TD with the same starting lamp voltage in dark room.
Page: 4/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
Relative humidity(%RH)
90
Operating Range
(40,90)
80
Storage Range
60
(50,50.4)
40
(60,27.7)
20
5
-20
20
40
Temperature(C)
50
60
Page: 5/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
3. ELECTRICAL CHARACTERISTICS
(1).TFT-LCD
ITEM
Power Supply Voltage for LCD
Power Supply Current for LCD
Permissive Ripple Voltage for Logic
Differential Resistance
SYMBOL
VCC
ICC
VRP
Zm
MIN
4.5
--90
Ta=25
TYP MAX UNIT REMARK
5.0
5.5
V
*1)
900 1500
mA
*2)
-100 mVp-p VCC=5.0V
100
110
VCM
1.125
1.25
1.375
250
350
450
mV
100
mV
-100
mV
*3)
LCDInrush Current
Inrush
*4)
Power consumption
4.5
7.5
*2)
[Note]
*1)Powerdata sequence
0.5mst110ms
t4200ms
0t250ms
t71sec
0t550ms
t3250ms
0.01mst610ms
Vin=5.0V
4.5V
4.5V
data
0.5V
0.5V
t1
t2
T5
T6
0.5V
T7
VL
T3
T4
Page: 6/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
VCC-dip conditions:
(1) When 3.6VVcc(min)<4.5V: td10 ms
(2) When Vcc <3.6 V,VCC-dip conditions should also follow the VCC-turn-on conditions.
Page: 7/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
(2).Backlight
1.Electrical specification
ITEM
SYMBOL MIN
TYP
MAX
UNIT
REMARK
Lamp Voltage
VL
720
800
880
Vrms
IL=7.5mA
Ta=25
Lamp Current(Standard)
IL
7.0
7.5
8.0
mArms
*1) Ta=25
Lamp Current(Operation)
ILO
3.0
7.5
8.0
mArms
*1) Ta=25
WL
28
FI
40
80
kHz
IL=7.0mA
Ta=25
*1) *2) Ta=25
1800
Vrms
*5) Ta=0
1550
Vrms
*5) Ta=25
VS
Page: 8/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
2.Lamp life time
ITEM
Lamp Life Time
Turn-on and Turn-off
Operation
E
2007/07/04
Technical Specification
IL at 3.0 mA
IL at 7.5 mA
IL at 8 mA
UNIT
Min. 50,000
Min. 40,000
Min. 30,000
hr
--
Min.100,000
--
time
REMARK
Continuous
Operation*3)
Continuous
Operation*4)
will become unequally or will deplete the Ar gas in it. Then it may cause the abnormal
phenomenon of lighting-up. Therefore, designers have to try their best to fulfill the
conditions under the inverter designing-stage as below:
1) Lamp Current measurement method (The current meter is inserted in cold line)
CTL
CTH
CTL
CTH
INVERTER
PowerSupply
LCD
CTL
Module
CTH
CTL
CTH
Page: 9/31
TitleCLAA201WA04
*2)
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
a. Frequency in this range can make the characteristics of electric and optics maintain in
+/- 10% except color coordinates.
b. Frequency in 50~60kHz can make characteristics of electric and optics better.
c. Frequency in 45~75kHz wont damage the lifetime and reliability of lamp.
d. Lamp frequency of inverter may produce interference with horizontal(or vertical)
synchronous frequency,and this may cause horizontal beat on the display.Therefore,
please adjust lamp frequency, and keep inverter as far from module as possible or use
electronic shielding between inverter and module to avoid the interference.
Page: 10/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Page: 11/31
TitleCLAA201WA04
No.
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Pin
Symbol
Description
HV
LV
HV
LV
HV
LV
HV
LV
CN2
CN3
CN4
CN5
Page: 12/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
5.INTERFACE TIMING
(1) Timing Characteristic
ITEM
SYMBOL
Freq.
fCLK
DCLK
Cycle
tCLK
Horizontal total time
tH
Horizontal Horizontal effective time
tHA
LCD
Horizontal blank time
tHB
Timing
Vertical frame Rate
Fr
DENA
Vertical total time
tV
Vertical
Vertical effective time
tVA
Vertical blank time
tVB
MIN.
61
12
1030
840
190
55
1060
1050
10
[Note]
*1) DENA (data enable) usually is positive
*2) DCLK still inputs during blanking
*3) LVDS transmitter IC: : NT71671-00033(NVT)
*4) LVDS IC
Receiver
Transmitter
DS90C384MTD(NS DS90C383MTD(NS
)
)
SN75LVDS82(TI)
SN75LVDS83(TI)
*5) DE mode only
*6) It maybe cause flicker at 55Hz
(2).Timing Chart
a. Horizontal Signal
DCLK
First Data
ODD DATA
(R,G,B)
Invalid Data
EVEN DATA
(R,G,B)
Invalid Data
tHB
Last Data
1677 1679
Invalid Data
1678 1680
Invalid Data
tHA
DENA
Page: 13/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
b. Vertical Signal
LINE DATA
Invalid Data
1049 1050
tVB
Invalid Data
tVA
DENA
(3).LVDS Data
For 6Bit+Hi-FRC
1CLK
RXOC
OB[6]
RXO4
RXO3
DE
VS
RXO2
OB[1]
OB[0]
OG[5]
RXO1
OG[0]
OR[5]
OR[4]
OB[7]
PREVIOUS
HS
OG[7]
OB[5]
OG[4]
OR[3]
OG[6]
OR[7]
OR[6]
OB[4]
OB[3]
OB[2]
OG[3]
OG[2]
OG[1]
OR[2]
OR[1]
OR[0]
NEXT
1CLK
RXEC
EB[7]
RXE4
EB[6]
EG[7]
EG[6]
ER[7]
ER[6]
EB[5]
EB[4]
EB[3]
EG[5]
EG[4]
EG[3]
EG[2]
EG[1]
ER[4]
ER[3]
ER[2]
ER[1]
ER[0]
RXE3
RXE2
EB[1]
EB[0]
EG[0]
RXE1
PREVIOUS
ER[5]
EB[2]
NEXT
Page: 14/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
R DATA
R6 R5 R4 R3 R2 R1 R0
LSB
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 1
0 0 0 0 0 1 0
G7
MSB
0
0
1
0
1
0
1
1
0
0
0
G DATA
G6 G5 G4 G3 G2 G1 G0
LSB
0 0 0 0 0 0 0
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
1 1 1 1 1 1 1
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
B7
MSB
0
0
0
1
1
1
0
1
0
0
0
B DATA
B6 B5 B4 B3 B2 B1 B0
LSB
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
1 1 1 1 1 1 1
1 1 1 1 1 1 1
1 1 1 1 1 1 1
0 0 0 0 0 0 0
1 1 1 1 1 1 1
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
RED(254)
RED(255)
GREEN(0)
GREEN(1)
GREEN(2)
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
GREEN(254)
GREEN(255)
BLUE(0)
BLUE(1)
BLUE(2)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
1
0
GREEN
BLUE
[Note]
BLUE(254)
BLUE(255)
1) Definition of gray scale: Color (n): n indicates gray scale level; higher n means brighter level.
2) Data: 1-High, 0-Low.
..
..
+
..
+
..
..
D(1679,1)
D(1680,1)
D(1679,2)
D(1680,2)
..
..
D(1679,Y)
D(1680,Y)
..
..
D(1679,1049) D(1680,1049)
D(1679,1050) D(1680,1050)
Page: 15/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
6.BLOCK DIAGRAM
CN2
CN3
CN4
CN5
Page: 16/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
7.MECHANICAL SPECIFICATION
(1) Front side (Tolerance is 0.5mm unless noted)
[Unit:mm]
Page: 17/31
TitleCLAA201WA04
E
2007/07/04
Technical Specification
Doc. No
Version
Issue Date
[Unit: mm]
Page: 18/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
8. OPTICAL CHARACTERISTICS
Ta=25VCC=5.0V
ITEM
Contrast (CEN)
SYMBOL CONDITION
= 0
CR
MIN.
TYP.
MAX.
UNIT REMARK
700
1000
--
--
*1)
Luminance (CEN)
= 0
250
300
--
cd/m2
*2)
9P Uniformity
= 0
75
80
--
*2)
Response Time
Tr+Tf
= 0
--
ms
*4)
Cross talk
CT
= 0
--
*5)
-75~75
-85~85
--
Deg.
-75~65
-85~75
--
Deg.
-75~75
-85~85
--
Deg.
-75~75
-85~85
--
Deg.
0.343
0.359
0.685
0.358
0.307
0.649
0.175
0.111
--
2.4
Horizontal
Vertical
Horizontal
Vertical
White
x
y
x
y
x
y
x
y
= 0
0.283
0.299
0.625
0.298
0.247
0.589
0.115
0.051
Gamut
CG
= 0
70
0.313
0.329
0.655
0.328
0.277
0.619
0.145
0.081
72
Gamma
VESA
2.0
2.2
View angle
Color
Coordinates
Red
Green
Blue
CR10
CR5
*3)
*2)
%
--
*6)
[Note]
Color coordinate and color gamut are measured by CS-1000, and all the other items are measured
by BM-5A(TOPCON). All these items are measured under the dark room condition (no ambient
light).
Measurement Condition: IL=7.5mA 4
Inverter: Sumida, model: IV50167/T
, Frequency=50kHz.
Page: 19/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
below.
9P Uniformity: L = (LMIN /LMAX) 100%
W
1/10 W
1 , 1
1/10 H
525
1680 , 1050
840
Upper
Right
Left
Lower
90 %
Luminan
10 %
tr
10 %
Black
tf
Page: 20/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
5) Definition of crosstalk:
CT=YB-YA/YA X 100 (%)
YA : The luminance of measured position at pattern A
YB : The luminance of measured position at pattern B with Gray level 0
Pattern A
Pattern B
T
%
y =x-k
Gray level(LOG)
Page: 21/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
CONDITIONS
50; 90%RH; 240h
(No condensation)
60; 90%RH;48h
(No condensation)
50; 240h
60; 240h
0; 240h
-20; 240h
BETWEEN -20(1hr)AND 60(1hr); 100
CYCLES
CONDITIONS
Shock level:100G
SHOCK
Waveform: half sinusoidal wave, 2ms
(NON-OPERATIO
Number of shocks: one shock input in each direction of three
N)
mutually perpendicular axes for a total of six shock inputs
Vibration level: 9.8m/s^2(1.0G) zero to peak
Waveform: sinusoidal
VIBRATION
Frequency range: 5 to 500 Hz
(NON-OPERATIO
Frequency sweep rate: 0.5 octave/min
N)
Duration: one sweep from 5 to 500Hz in each of three mutually
perpendicular axis(each x,y,z axis: 1 hour, total 3 hours)
(3) ESD
POSITION
Connector
Module
CONDITION
260HPa (30000 ft.)24 Hr
Page: 22/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Page: 23/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Page: 24/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Page: 25/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
(b)
(c)
(a)
A
AYear
BWeek
DEFGHSerial No.
IFactory Code
Page: 26/31
TECHNICAL SPECIFICATION
TitleCLAA201WA04
E
2007/07/04
Technical Specification
[Note]
(1) Year
Year
2000
2001
2002
2003
2004
2005
2006
2007
Mark
(2) Week
Week
10
11
12
Mark
01
02
03
04
05
06
07
08
09
10
11
12
1~99,999
Mark
00001~99999
Factory
Code
Mark
L
Factory
WJ1
Factory
WJ2
Factory
XAT04KDE
LABEL ( F201WA04xxxxxxxxxxxxxxxxxxx)
F201WA04xxxxxxxxxxxxxxxxxxx
(2) Location of Lot Mark
The label is attached to the backside of the LCD Module. This is subject to change
without prior notice.
Page: 27/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Page: 28/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
Page: 29/31
TitleCLAA201WA04
Doc. No
Version
Issue Date
E
2007/07/04
Technical Specification
(3) Please do not leave the LCDs in the environment of low temperature; below -20.
5. SAFETY PRECAUTIONS
(1) When you waste LCDS, it is recommended to crush damaged or unnecessary LCDs
into pieces and wash them off with solvents such as acetone and ethanol, which should
later be burned.
(2) If any liquid leaks out of a damaged-glass cell and comes in contact with the hands,
wash off throughly with soap and water.
6. OTHERS
(1) A strong incident light into LCD panel might cause display characteristics' changing
inferior because of polarizer film, color filter, and other materials becoming inferior.
Please do not expose LCD module direct sunlight Land strong UV rays.
(2) Please pay attention to a panel side of LCD module not to contact with other materials
in preserving it alone.
(3) For the. packaging box, please pay attention to the followings:
(3.1) Packaging box and inner case for LCD are designed to protect the LCDs from the
damage or scratching during transportation. Please do not open except picking
LCDs up from the box.
(3.2) Please do not pile them up more than 5 boxes. (They are not designed so.) And
please do not turn over.
(3.3) Please handle packaging box with care not to give them sudden shock and
vibrations.And also please do not throw them up.
(3.4) Packing box and inner case for LCDs are made of cardboard. So please pay
attention not to get them wet. (Such like keeping them in high humidity or wet
place can occur getting them wet.)
Page: 30/31