Edition 2: Volume 3
Copyright
http://creativecommons.org/licenses/by/3.0/au/
State of Queensland (Department of Transport and Main Roads) 2015
Feedback: Please send your feedback regarding this document to: tmr.techdocs@tmr.qld.gov.au
Road Planning & Design Manual Edition 2: Volume 3, Transport and Main Roads, April 2015
Where a section does not appear in the body of this supplement, the Austroads Guide to Road Design
Part 7 criteria is accepted unamended.
This supplement:
has precedence over the Austroads Guide to Road Design Part 7 when applied in
Queensland
has the same structure (section numbering, headings and contents) as Austroads Guide to
Road Design Part 7.
The following table summarises the relationship between the Austroads Guide to Road Design - Part 7
and this supplement using the following criteria:
Accepted:
Accepted with
Amendments:
Part or all of the section has been accepted with additions and or
differences.
New:
Not accepted:
RPDM relationship
1 Introduction
1.1
Accepted
1.2
1.3
Accepted
Preliminary investigation
Accepted
2.2
Accepted
2.3
Accepted
2.4
Accepted
2.5
Accepted
Road Planning & Design Manual Edition 2: Volume 3, Transport and Main Roads, April 2015
Seismic surveys
Accepted
3.2
Accepted
3.3
Penetrometer testing
Accepted
3.4
Accepted
3.5
Trenching
Accepted
3.6
Sampling of materials
Accepted
4 Design elements
4.1
General
Accepted
4.2
Horizontal alignment
Accepted
4.3
Vertical alignment
Accepted
4.4
Cuttings
4.5
Embankments
Accepted
4.6
Pavements
Accepted
4.7
Accepted
4.8
Accepted
General
Accepted
5.2
Materials stewardship
Accepted
5.3
Minimisation of erosion
Accepted
5.4
Accepted
5.5
Preservation of topsoil
Accepted
5.6
Accepted
References
Accepted
References
Appendices
Accepted
Appendix A
Laboratory tests
Accepted
Appendix B
Accepted
Road Planning & Design Manual Edition 2: Volume 3, Transport and Main Roads, April 2015
ii
Contents
1
Introduction ....................................................................................................................................1
1.2
References ..............................................................................................................................................2
Road Planning & Design Manual Edition 2: Volume 3, Transport and Main Roads, April 2015
iii
Supplement to Austroads Guide to Road Design Part 7: Geotechnical Investigation and Design
1
1.2
Introduction
Scope of this part of the Guide to Road Design
Additions
The Austroads Guide to Road Design Part 7 Geotechnical Investigation and Design provides
general details regarding geotechnical investigations and how road design outcomes and other design
activities are influenced by site conditions, associated ground response, geological hazards and
locally available materials. The Department of Transport and Main Roads Geotechnical Design
Standard Minimum Requirements, defines the minimum geotechnical requirements which shall be
met for all projects throughout Queensland.
4
4.4.1
Design elements
Presence of rock
Additions
AS 2868-1986 has been withdrawn. Instead of AS 2868-1986, Clause 3.3 of Transport and Main
Roads Specifications MRTS04 General Earthworks should be adopted.
Road Planning & Design Manual Edition 2: Volume 3, Transport and Main Roads, April 2015
Supplement to Austroads Guide to Road Design Part 7: Geotechnical Investigation and Design
References
Transport and Main Roads publication references refer to the latest published document on the
departmental website (www.tmr.qld.gov.au).
Additions
Transport and Main Roads Geotechnical Design Standard Minimum Requirements, Brisbane, QLD
Transport and Main Roads Specifications MRTS04 General Earthworks, Brisbane, QLD
Road Planning & Design Manual Edition 2: Volume 3, Transport and Main Roads, April 2015