As Required by the Provisions of the ASME Code Rules, Section VIII, Division 1
1. Manufactured and certified by
2. Manufactured for
3. Location of installation
4. Type:
(CRN)
(Drawing No.)
(Year built)
Items 611 incl. to be completed for single wall vessels, jackets of jacketed vessels, shell of heat exchangers, or chamber of multichamber vessels.
6. Shell (a) No. of course(s):
(b) Overall length (ft & in.):
Course(s)
No.
Diameter, in.
Material
7. Heads: (a)
Thickness
Spec./Grade or Type
Nom.
Corr.
Type
(b)
Thickness
Location (Top,
Bottom, Ends)
Min.
Corr.
Radius
Crown
Knuckle
Elliptical
Ratio
Type
Heat Treatment
Eff.
Temp.
Time
Conical
Hemispherical
Apex Angle
Radius
Flat
Diameter
Side to Pressure
Convex
Category A
Concave
Type
Eff.
(a)
(b)
8. Type of jacket
Jacket closure
(internal)
(external)
(internal)
(external)
psi.
at test temperature of
F at
F.
Proof test
13. Tubes:
(Dia., in.)
(O.D., in.)
(Attachment)
(Number)
Items 1418 incl. to be completed for inner chambers of jacketed vessels or channels of heat exchangers.
14. Shell (a) No. of course(s)
(b) Overall length (ft & in.):
Course(s)
No.
Diameter, in.
Material
Thickness
Spec./Grade or Type
Nom.
Corr.
Thickness
Min.
Corr.
Radius
Crown
Knuckle
Elliptical
Ratio
Conical
Apex Angle
(b)
Type
Heat Treatment
Eff.
Temp.
Hemispherical
Radius
Flat
Diameter
Side to Pressure
Convex
Concave
Category A
Type
(a)
(b)
(7/00)
Time
This form (E00108) may be obtained from the Order Dept., ASME, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300.
E00108
Eff.
(external)
F at
psi.
(external)
at test temperature of
F.
Proof test
Diameter
or Size
No.
Lugs
(Yes or no)
Material
Flange
Type
Nozzle
Flange
Legs
(No.)
Nozzle Thickness
Nom.
Corr.
Others
(No.)
Reinforcement
Material
How Attached
Nozzle
Flange
Location
(Insp. Open.)
Attached
(Describe)
21. Manufacturers Partial Data Reports properly identified and signed by Commissioned Inspectors have been furnished for the following items of
the report: (List the name of part, item number, mfgs. name and identifying number)
22. Remarks:
Expires
Name
Signed
(Manufacturer)
(Representative)
, and
state that, to the best of my knowledge and belief, the Manufacturer has constructed this pressure vessel in accordance with ASME Code, Section
VIII, Division 1. By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the pressure
vessel described in this Manufacturers Data Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any
personal injury or property damage or a loss of any kind arising from or connected with this inspection.
Date
Signed
Commissions
(Authorized Inspector)
Name
Signed
(Assembler)
(Representative)
, have compared the statements in this Manufacturers Data Report with the described pressure vessel
and state that parts referred to as data items
, not included in the certificate of shop inspection, have been
inspected by me and to the best of my knowledge and belief, the Manufacturer has constructed and assembled this pressure vessel in accordance
with the ASME Code, Section VIII, Division 1. The described vessel was inspected and subjected to a hydrostatic test of
psi.
By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the pressure vessel
described in this Manufacturers Data Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal
injury or property damage or a loss of any kind arising from or connected with this inspection.
Date
Signed
Commissions
(Authorized Inspector)