Data
50DJ,DK,DW,DY
WeathermakerT II
Rooftop Units
Cooling with
Optional Electric Heat
20 to 27 Nominal Tons
Features/Benefits
Design flexibility
Dedicated vertical supply/return unit
(Model 50DJ,DK) is ideal for new construction. The low unit profile is
maintained when the unit is installed
on the accessory roof curb, which
is approved by the National Roofing
Contractors Association (NRCA). The
roof curb is made watertight by the
roofer.
The ducts are attached directly to
the roof curb to allow all ductwork
to be completed before the unit is
positioned.
Dedicated horizontal unit (Model
50DW,DY) is ideal for replacement or
special applications such as thru-thewall jobs or jobs where sound must be
attenuated before the duct penetrates
the roof. Ducts connect directly to
unit, using factory-supplied flanges.
Horizontal units may be curb mounted
or slab mounted.
Unit efficiency
Dual serviceable, semi-hermetic compressors on intertwined evaporator
coil ensures excellent full and part-load
efficiency with EERs (Energy Efficiency Ratio) to 9.7. Dual refrigerant
circuits provide standby capability
should one circuit require service.
Copyright 1992 Carrier Corporation
Form 50DJ,DK-5PD
Installation/serviceability
Small footprint requires less roof area
and makes unit easier to rig. Low
2
Unit controls
Constant volume units (Model
50DJ,DW) utilize a solid-state relay
board that interfaces with any 2-stage
heat/2-stage cool thermostat. Economizer units utilize a mixed air thermistor with a field-adjustable set point.
Variable volume units (Model
50DK,DY) utilize a self-diagnostic
microprocessor based control. The
microprocessor monitors stages of
cooling, morning warm-up cycle and
unit safety controls. At start-up, the
self-diagnostic test verifies component
operation and calibration. Fault codes
reduce service troubleshooting time
and difficulty.
Table of contents
Page
Features/Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2
Model Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Physical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
EER (Energy Efficiency Ratio) and IPLV
(Integrated Part-Load Value) Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Options and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Base Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8,9
Accessory Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10,11
Selection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-18
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-24
Typical Wiring Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Typical Piping and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Application Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29,30
Guide Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-36
Physical data
CONSTANT VOLUME UNITS
BASE UNIT 50
NOMINAL CAPACITY (tons)
OPERATING WEIGHT (lb)*
COMPRESSORS (2 each unit)
Capacity Steps (%) Standard
Accessory
REFRIGERANT
Operating Charge (lb), Sys 1/Sys 2
CONDENSER COILS
Face Area (sq ft)
Fins Per Inch (Al)
(Cu)
EVAPORATOR COILS
Face Area (sq ft)
Fins Per Inch
OUTDOOR AIR FANS (2 each unit)
Nominal Cfm
Nominal Hp
Watts Input (Total)
INDOOR AIR FANS (1 each unit)
Nominal Cfm
Maximum Allowable Cfm
Maximum Allowable Rpm
Standard Motor and Drive
Motor Hp
Full Load Efficiency (%)
Standard
High
Motor Frame Size
Fan Pulley Pitch Diameter (in.)
Motor Pulley Pitch Diameter (in.)
Resulting Fan Rpm
Belts
Quantity
Length (in.)
Optional Motor and Drive
Motor Hp
Full Load Efficiency (%)
Standard
High
Motor Frame Size
Fan Pulley Pitch Diameter (in.)
Motor Pulley Pitch Diameter (in.)
Resulting Fan Rpm
Belts
Quantity
Length (in.)
Optional Power Exhaust**
Motors...Hp
Fans...Diameter (in.)
Filters (Quantity...L x W x D)
20% Standard Efficiency
Disposable
DJ024
20
2440
DW024
DJ028
DW028
DJ030
DW030
20
25
25
27
27
2650
2900
3100
2930
3140
Semi-Hermetic, 06D Type, 1750 Rpm
62, 100
60, 100
55, 100
21, 42, 62, 80, 100
20, 40, 60, 80, 100
18, 37, 55, 100
R-22, Controlled by Thermostatic Expansion Valve
23.1/18.1
22.6/16.3
22.3/18.3
3-Row, 38-in. Tube Diameter
24.75
17.0
19.0
19.0
15.7
17.5
17.5
4-Row, 12-in. Tube Diameter
20.1
23.4
23.4
15
15
15
Propeller Type, 30-in. Diameter, 1140 Rpm
10,000
13,000
15,000
34 (208/230, 460 v); 1 (575 v)
1
1
1700
2400
2900
Centrifugal Type, 18 x 15-in.
8,000
10,000
10,800
10,000
12,500
12,500
1,200
1,200
1,200
1.438-in. Fan Pulley Bore, Service Factor 1.15
5
712
10
84.3
86.5
184T
10.6
4.75
780
2
56
712
84.8
88.5
213T
8.0
4.12
900
2
2
2
85
47
85
1.438-in. Fan Pulley Bore, Service Factor 1.15
10
84.8
88.5
213T
8.0
4.12
900
3
47
2
47
2
80
1...1
1...24
NA
2...18 x 24 x 2
4...24 x 24 x 2
3
3
47
85
Propeller Type, 1140 Rpm
1...1
NA
1...30
2...18 x 24 x 2
6...20 x 24 x 2
296
3
85
15
87.4
89.5
215T
8.0
4.50
980
*Weights do not include economizer. See page 6 for weights of options and accessories.
Standard fan motor is supplied with standard fan drive and belts. Optional fan motor is supplied with
optional fan drive, pulleys, and belts. Other combinations are field supplied.
**Optional unit-mounted power exhaust not available (NA) on Models 50DW. Accessory constant volume power exhaust may be duct mounted on 50DW installation.
87.4
89.5
215T
8.0
4.50
980
85.7
90.0
254T
8.0
5.00
1090
3
50
3
85
1...1
1...30
NA
2...18 x 24 x 2
6...20 x 24 x 2
BASE UNIT 50
NOMINAL CAPACITY (tons)
OPERATING WEIGHT (lb)*
COMPRESSORS (2 each unit)
Capacity Steps (%) Standard
REFRIGERANT
Operating Charge (lb), Sys 1/Sys2
CONDENSER COILS
Face Area (sq ft)
Fins Per Inch (Al)
(Cu)
EVAPORATOR COILS
Face Area (sq ft)
Fins Per Inch
OUTDOOR AIR FANS (2 each unit)
Nominal Cfm
Nominal Hp
Watts Input (Total)
INDOOR AIR FANS (1 each unit)
Nominal Cfm
Maximum Allowable Cfm
Maximum Allowable Rpm
Standard Motor and Drive
Motor Hp
Full Load Efficiency (%)
Standard
High
Motor Frame Size
Fan Pulley Pitch Diameter (in.)
Motor Pulley Pitch Diameter (in.)
Resulting Fan Rpm
Belt (No Inlet Guide Vanes)
Quantity
Length (in.)
Belts (Inlet Guide Vanes)
Quantity
Length (in.)
Optional Motor and Drive
Motor Hp
Full Load Efficiency (%)
Standard
High
Motor Frame Size
Fan Pulley Pitch Diameter (in.)
Motor Pulley Pitch Diameter (in.)
Resulting Fan Rpm
Belts (No Inlet Guide Vanes)
Quantity
Length (in.)
Belts (Inlet Guide Vanes)
Quantity
Length (in.)
Optional Power Exhaust**
Motors...Hp
Fans...Diameter (in.)
Filters (Quantity...L x W x D)
20% Standard Efficiency
Disposable
DK024
20
2440
DY024
DK028
DY028
DK030
DY030
20
25
25
27
27
2650
2900
3100
2930
3140
Semi-Hermetic, 06D Type, 1750 Rpm
21, 42, 62, 80, 100
20, 40, 60, 80, 100
18, 37, 55, 100
R-22, Controlled by Thermostatic Expansion Valve
25.2/18.1
24.6/16.3
24.3/18.3
3-Row, 38-in. Tube Diameter
24.75
17.0
19.0
19.0
15.7
17.5
17.5
4-Row, 12-in. Tube Diameter
20.1
23.4
23.4
15
15
15
Propeller Type, 30-in. Diameter, 1140 Rpm
10,000
13,000
15,000
34 (208/230, 460 v); 1 (575 v)
1
1
1700
2400
2900
Centrifugal Type, 18 x 15-in.
8,000
10,000
10,800
10,000
12,500
12,500
1,200
1,200
1,200
1.438-in.Fan Pulley Bore, Service Factor 1.15
5
712
10
84.3
86.5
184T
10.6
4.75
780
84.8
88.5
213T
8.0
4.12
900
2
56
2
85
2
53
712
2
47
87.4
89.5
215T
8.0
4.50
980
2
85
2
2
2
95
45
90
1.438-in. Fan Pulley Bore, Service Factor 1.15
10
84.8
88.5
213T
8.0
4.12
900
3
47
3
85
2
53
2
100
15
87.4
89.5
215T
8.0
4.50
980
2
47
2
80
2
45
2
90
1...1
1...24
NA
2...18 x 24 x 2
4...24 x 24 x 2
3
47
85.7
90.0
254T
8.0
5.00
1090
3
85
3
50
3
85
2
2
53
100
Propeller Type, 1140 Rpm
1...1
NA
1...30
3
45
3
95
1...1
1...30
NA
2...18 x 24 x 2
6...20 x 24 x 2
2...18 x 24 x 2
6...20 x 24 x 2
*Weights do not include economizer. See page 6 for weights of options and accessories.
Standard fan motor is supplied with standard fan drive and belts. Optional fan motor is supplied with
optional fan drive, pulleys, and belts. Other combinations are field supplied.
**Optional unit-mounted power exhaust not available (NA) on Models 50DY. Accessory modulating
power exhaust may be duct mounted on 50DY installations.
296
UNIT
50DJ,DK
50DW,DY
024
028
030
024
028
030
1
749
883
891
791
910
921
WEIGHT OF
CORNER (lb)
2
3
4
491
531
809
579
625
953
585
632
962
520
586
893
613
691
1026
620
700
1039
OPTION OR ACCESSORY
ROOFCURB
Vertical Supply/Return (50DJ,DK)
Horizontal Supply/Return (50DW,DY)
ECONOMIZER
ECONOMIZER RAINHOOD
25% OUTDOOR AIR HOOD
POWER EXHAUST
CV
VAV
HOOD FOR POWER EXHAUST OR
BAROMETRIC RELIEF
CV
VAV
HAIL GUARD
ELECTRIC HEAT (kW)
18
36
72
90
108
ALTERNATE MOTOR AND DRIVE
Size 024
028
030
COPPER CONDENSER
Size 024
028,030
INLET GUIDE VANES (VAV Only)
DIM
(ft-in.)
A
B
4-1
3-8
4-5
3-8
4-5
3-8
5-1
3-7
5-6
3-7
5-6
3-7
WEIGHT (lb)
250
280
140
140
40
50
70
100
110
40
75
85
110
110
110
45
25
45
104
143
100
CV Constant Volume
VAV Variable Air Volume
EER*
9.7
9.7
9.6
9.6
9.0
9.0
8.8
8.8
8.6
8.6
8.5
8.5
IPLV*
11.2
10.0
10.9
9.8
10.2
8.9
9.6
8.4
9.5
8.4
9.0
8.0
296
024
028
030
Standard
VARIABLE AIR
VOLUME
(DK,DY)
21,42,62,80,100
20,40,60,80,100
18,37,55,65,83,100
OPTION*
X
X
X
X
ACCESSORY
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
LEGEND
CV Constant Volume
VAV Variable Air Volume
*Factory installed
Field installed
**Not available on 575-v units
Unit mounted on downflow units; duct mounted on horizontal units.
ELECTRIC HEATER
POWER EXHAUST
Heaters are available in a wide range of capacities for factory or field installation. Most heater packages are wired for 2-stage heat. On VAV units, electric
heat is used for morning warm-up only, and is wired only for single-stage heat.
SET POINT
POTENTIOMETER
DISPLAY
DISPLAY
BUTTON
ECONOMIZER
DISPLAY
20
10
0
10
20
30
40
10
30
0
10
20
50
60
C
F
20
70
Integrated economizer saves energy by using low temperature outside air to provide cooling. The electronic control logic located in the economizer motor integrates economizer cooling with mechanical cooling. If the conditioned space requires more cooling, mechanical cooling will be brought on to satisfy the cooling
need. Solid-state enthalpy control senses both dry- and wet-bulb of the outdoor air
to provide an accurate enthalpy reading. Differential enthalpy sensor compares
outdoor temperature and humidity to return air temperature and humidity and determines the most economic mixture of air. Spring return damper motor automatically closes the outdoor air dampers in the event of a power failure.
UNIT
SIZE
WEIGHT
Lbs
Kg
A
mm
50DJ024
2580 1172.7 1244.6
50DK024
50DJ028
3040 1381.8
50DK028
1346.2
50DJ030
3070 1395.5
50DK030
B
ft-in.
mm
C
ft-in.
mm
D
ft-in.
mm
E
ft-in.
mm
F
ft-in.
4-1
4-5
1956.0
6-5
3397.0 11-134
382.5 1-3116
mm
ft-in.
2048.0 6- 858
] are in millimeters.
Center of gravity.
3. Allow 128-09 (3658) at top and 68-09 (1829) on sides for service
and operational clearance.
4. On multiunit applications allow 128-09 (3658) between adjacent
condensers and economizers.
5. For smaller service and operational clearances, contact Carrier
Application Engineering Department.
6. Always line up condenser end of unit tight against the roof curb.
7. When unit is slab mounted, locate the condensate drain as low
as possible on vertical face of base rail at the same location as
the standard condensate drain using factory supplied fitting. Plug
factory drilled condensate hole.
UNIT
SIZE
WEGHT*
lbs
kgs
A
mm
50DW024
2790 1268.2 1549.4
50DY024
50DW028
3240 1472.7
50DY028
1676.4
50DW030
3280 1490.9
50DY030
B
ft-in.
mm
C
ft-in.
mm
D
ft-in.
5-1
2182.0 7-1
5-6
78
682.0 2-2
mm
78
E
ft-in.
3909.0 12-9
78
13-8
mm
ft-in.
533.5
1-9
379.5 1-21516
296
NOTES:
1. Roof curb accessory 50DJ900391 is shipped
disassembled.
2. Dimensions in ( ) are millimeters.
3. Roof curb: 16 gage (VA03-56) steel.
4. The 028 and 030 units overhang the roof curbs
on supply air/return air end.
10
B
Deg
1.00
C
in.
3.25
Deg
.50
D
in.
.75
Deg
.50
in.
.75
NOTES:
1. Roof curb accessory 50DJ900401 is shipped
disassembled.
2. Dimensions in ( ) are millimeters.
3. Roof curb: 16 gage (VA03-56) steel.
4. The 028 and 030 units overhang the roof curbs
on the return air end.
B
Deg
1.38
C
in.
4.00
Deg
.50
D
in.
.75
Deg
.50
in.
.75
11
Performance data
COOLING CAPACITIES
50DJ,DK,DW,DY024
Temp (F)
Air Entering
Condenser
85
95
100
105
115
120
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
4000/0.02
72
239
114
17.1
229
110
18.5
223
108
19.2
217
106
19.9
207
101
21.3
201
99
21.9
67
220
138
16.5
210
134
17.8
205
131
18.4
200
129
19.1
190
125
20.3
185
123
21.0
62
201
161
15.8
192
156
17.0
188
154
17.6
183
151
18.2
174
147
19.5
170
145
20.0
72
247
123
17.4
235
118
18.8
230
116
19.5
224
114
20.2
212
109
21.6
207
107
22.2
7000/0.04
62
218
197
16.5
208
191
17.7
203
188
18.4
199
185
19.0
189
178
20.3
184
175
20.9
50DJ,DK,DW,DY024
Temp (F)
Air Entering
Condenser
85
95
100
105
115
120
12
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
8000/0.05
72
266
146
18.1
254
142
19.5
247
139
20.3
241
137
21.0
227
132
22.4
221
130
23.0
67
249
191
17.5
237
186
18.9
230
183
19.5
224
181
20.2
212
175
21.6
205
172
22.2
62
232
230
16.9
222
221
18.2
217
216
19.0
212
212
19.6
202
202
20.9
197
197
21.7
10,000/0.06
72
271
160
18.3
259
155
19.7
252
153
20.5
245
150
21.2
231
145
22.6
224
143
23.3
67
255
213
17.7
242
208
19.0
236
205
19.8
230
202
20.5
216
196
21.8
210
193
22.5
62
244
244
17.4
233
233
18.7
228
228
19.5
223
223
20.1
211
211
21.5
206
206
22.2
72
263
139
17.9
250
134
19.4
244
132
20.1
238
130
20.8
224
125
22.2
218
123
22.9
67
245
179
17.4
233
174
18.7
227
171
19.4
220
169
20.0
209
164
21.4
202
161
22.0
62
227
214
16.8
216
209
18.1
211
205
18.7
206
202
19.3
195
194
20.6
190
190
21.3
85
95
100
105
115
120
5000/0.02
72
314
150
25.1
300
144
27.1
293
141
28.0
286
138
28.9
272
133
30.9
266
130
31.8
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
67
290
180
24.1
277
174
25.9
270
171
26.7
265
169
27.7
252
162
29.4
245
160
30.4
62
266
209
23.0
254
202
24.7
249
199
25.5
242
197
26.3
231
191
28.0
226
188
28.8
72
324
160
25.6
309
154
27.6
302
151
28.5
294
148
29.5
279
143
31.4
272
140
32.3
8750/0.04
62
288
255
24.0
275
247
25.7
268
244
26.7
262
241
27.5
249
233
29.3
242
229
30.1
72
345
180
26.5
328
174
28.5
319
172
29.5
311
169
30.5
294
162
32.4
286
159
33.4
67
322
231
25.5
306
225
27.4
298
221
28.3
290
218
29.3
275
212
31.1
268
208
32.0
62
299
277
24.5
285
271
26.2
278
266
27.2
272
263
28.1
258
254
29.9
252
249
30.8
50DJ,DK,DW,DY028
Temp (F)
Air Entering
Condenser
85
95
100
105
115
120
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
10,000/0.04
72
350
190
26.8
333
183
28.8
324
181
29.8
316
178
30.7
298
172
32.7
289
168
33.7
67
328
247
25.8
311
240
27.6
303
237
28.6
295
234
29.5
279
227
31.3
271
224
32.3
62
306
298
24.7
291
287
26.6
285
282
27.6
278
277
28.4
265
264
30.4
258
258
31.4
Bypass Factor
Entering Wet-Bulb
Compressor Motor Power Input
Sensible Heat Cap. (1000 Btuh)
Total Cap. (1000 Btuh) Gross
NOTES:
1. Direct interpolation is permissible. Do not extrapolate.
2. The following formulas may be used:
tldb = t edb
1.10 x cfm
tlwb = Wet-bulb temperature corresponding to enthalpy of air
leaving evaporator coil (hlwb ).
hlwb = hewb
4.5 x cfm
Where: hewb = Enthalpy of air entering evaporator coil.
12,500/0.06
72
356
208
27.0
339
201
29.0
331
199
30.0
322
195
31.0
303
189
33.0
294
185
33.9
67
335
276
26.1
318
269
28.0
310
265
29.0
302
261
30.0
286
254
31.8
278
251
32.8
62
318
318
25.3
305
305
27.4
299
299
28.3
291
291
29.3
278
278
31.3
271
271
32.3
BF
79
81
.05
.10
.20
1.04
.98
.87
Interpolation is permissible.
Correction Factor = 1.10 x (1 - BF) x (edb - 80).
4. Cooling capacities are gross and do not include deduction for indoor fan motor
heat.
13
85
95
100
105
115
5400/0.02
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
72
336
161
26.6
323
155
28.7
316
152
29.8
308
149
30.8
294
143
32.9
67
310
193
25.5
297
187
27.4
291
184
28.4
284
180
29.4
272
175
31.2
62
283
223
24.2
273
218
26.2
267
214
27.1
261
211
27.9
249
206
29.7
72
352
172
27.3
338
167
29.5
331
164
30.6
323
161
31.6
306
154
33.6
9450/0.05
62
312
275
25.6
298
268
27.5
291
264
28.4
284
260
29.4
270
253
31.2
72
372
194
28.2
355
188
30.3
347
185
31.5
338
182
32.5
320
175
34.6
67
346
247
27.1
330
241
29.0
323
238
30.2
313
235
31.1
297
228
33.0
62
321
297
26.0
307
290
27.9
299
285
28.8
292
282
29.9
277
272
31.7
50DJ,DK,DW,DY030
Temp (F)
Air Entering
Condenser
85
95
100
105
115
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
TC
SHC
kW
72
378
204
28.4
360
198
30.6
352
195
31.7
342
192
32.8
325
185
34.9
Bypass Factor
Entering Wet-Bulb
Compressor Motor Power Input
Sensible Heat Cap. (1000 Btuh)
Total Cap. (1000 Btuh) Gross
NOTES:
1. Direct interpolation is permissible. Do not extrapolate.
2. The following formulas may be used:
tldb = t edb
1.10 x cfm
tlwb = Wet-bulb temperature corresponding to enthalpy of air
leaving evaporator coil (h lwb ).
hlwb = hewb
14
62
335
331
26.6
320
320
28.6
314
314
29.7
306
306
30.6
293
243
32.8
BF
79
81
.05
.10
.20
1.04
.98
.87
Interpolation is permissible.
Correction Factor = 1.10 x (1 - BF) x (edb - 80).
4. Cooling capacities are gross and do not include deduction for indoor fan motor
heat.
VOLTAGE
LOW (kW)
Single Stage
208
230
460
575
208
230
460
575
208
230
460
575
15
18
18
N/A
15
18
18
N/A
15
18
18
N/A
DJ
024,028,030
DW
024
DW
028,030
MED (kW)
Two Stages
1st
1st and 2nd
15
29
18
36
18
36
18
36
15
29
18
36
18
36
18
36
15
29
18
36
18
36
18
36
HIGH (kW)
Two Stages
1st
1st and 2nd
29
59
36
72
54
90
54
72
45
74
54
90
54
90
54
90
45
74
54
90
72
108
72
108
VOLTAGE
DK,DY
024,028,030
208
230, 460
575
LOW (kW)
Single Stage
15
18
N/A
MED (kW)
Single Stage
29
36
36
FAN PERFORMANCE 50DJ UNITS AND 50DK UNITS WITHOUT INLET GUIDE VANES
UNIT
50DJ,DK
AIRFLOW
(Cfm)
024
6,000
7,000
8,000
9,000
10,000
UNIT
50DJ,DK
AIRFLOW
(Cfm)
024
(cont)
6,000
7,000
8,000
9,000
10,000
UNIT
50DJ,DK
AIRFLOW
(Cfm)
028,030
7,000
8,000
9,000
10,000
11,000
12,000
12,500
UNIT
50DJ,DK
AIRFLOW
(Cfm)
028,030
(cont)
7,000
8,000
9,000
10,000
11,000
12,000
12,500
0.2
Rpm Bhp
570
1.8
630
2.7
690
3.8
760
5.2
830
6.7
0.4
Rpm Bhp
620
2.2
670
2.9
730
4.2
800
5.4
860
7.2
0.6
Rpm Bhp
660
2.4
710
3.3
770
4.5
830
5.8
890
7.6
1.6
Rpm Bhp
850
3.8
890
4.7
930
6.2
990
8.1
1040 10.1
1.8
Rpm Bhp
880
4.0
930
5.2
960
6.6
1020
8.6
1060 10.5
2.0
Rpm Bhp
920
4.3
960
5.6
1000
7.2
1040
8.9
1090 10.8
2.2
Rpm Bhp
950
4.7
990
6.2
1030
7.6
1070
9.4
1120 11.1
2.4
Rpm Bhp
980
5.2
1030
6.6
1060
8.0
1100
9.7
1150 11.6
2.6
Rpm Bhp
1020
5.7
1060
6.9
1080
8.3
1130 10.2
1170 12.0
AVAILABLE
2.8
Rpm Bhp
1050
5.9
1080
7.2
1120
8.7
1160 10.6
1190 12.4
3.6
Rpm Bhp
1150 7.3
1180 8.8
3.8
Rpm Bhp
1180 7.7
4.0
Rpm Bhp
1200 8.0
0.2
Rpm Bhp
550
2.3
590
3.1
640
4.4
710
5.7
770
7.0
850
9.2
870 10.0
0.4
Rpm Bhp
590
2.5
630
3.5
690
4.6
750
5.9
820
7.5
870
9.5
910 11.0
0.6
Rpm Bhp
630
2.8
670
3.8
730
4.9
800
6.3
850
8.0
910 10.4
940 11.5
1.6
Rpm Bhp
830
4.3
860
5.3
900
6.6
980
9.2
1000 10.6
1050 12.7
1070 13.7
1.8
Rpm Bhp
870
4.6
900
5.7
940
7.2
1010
9.6
1030 11.1
1070 13.2
1100 14.5
2.0
Rpm Bhp
900
4.9
930
6.1
970
7.8
1030
9.9
1060 11.5
1100 13.7
1120 14.8
2.2
Rpm Bhp
930
5.2
960
6.6
1000
8.4
1060 10.2
1080 12.0
1130 14.3
1150 15.4
2.4
Rpm Bhp
970
5.7
1000
7.2
1030
8.7
1090 10.8
1110 12.5
1160 14.8
1170 15.8
2.6
Rpm Bhp
1000
6.3
1030
7.6
1060
9.2
1120 11.1
1130 12.8
1180 15.3
1200 16.5
AVAILABLE
2.8
Rpm Bhp
1030
6.7
1060
8.0
1090
9.5
1140 11.4
1160 13.1
1200 15.6
3.6
Rpm Bhp
1140
7.9
1170
9.5
1190 11.1
3.8
Rpm Bhp
1170 8.2
1190 9.9
4.0
Rpm Bhp
1190 8.8
15
AIRFLOW
(Cfm)
024
6,000
7,000
8,000
9,000
10,000
UNIT
50DW,DY
AIRFLOW
(Cfm)
024
(cont)
6,000
7,000
8,000
9,000
10,000
UNIT
50DW,DY
AIRFLOW
(Cfm)
028,030
7,000
8,000
9,000
10,000
11,000
12,000
12,500
UNIT
50DW,DY
AIRFLOW
(Cfm)
028,030
(cont)
7,000
8,000
9,000
10,000
11,000
12,000
12,500
0.2
Rpm Bhp
570
1.9
650
2.9
720
4.1
800
5.4
870
7.2
0.4
Rpm Bhp
620
2.1
690
3.1
760
4.4
830
5.8
900
7.7
0.6
Rpm Bhp
670
2.5
730
3.5
790
4.7
870
6.2
930
8.3
2.2
Rpm Bhp
970
5.0
1020
6.5
1060
7.9
1110
9.8
1160 11.8
2.4
Rpm Bhp
1010
5.5
1050
6.8
1090
8.2
1140 10.4
1180 12.1
1200 12.5
0.2
Rpm Bhp
630
2.7
670
3.7
740
5.0
810
6.4
870
8.4
950 11.0
980 12.2
0.4
Rpm Bhp
680
3.0
720
4.0
780
5.2
840
6.9
910
9.1
980 11.6
1020 12.9
0.6
Rpm Bhp
720
3.3
760
4.3
810
5.5
870
7.4
940
9.5
1010 12.1
1040 13.3
2.2
Rpm Bhp
1000
6.3
1030
7.7
1070
9.3
1120 11.1
1170 13.3
2.4
Rpm Bhp
1030
6.7
1060
8.1
1100
9.6
1150 11.5
1200 13.9
AVAILABLE
2.6
Rpm Bhp
1060
7.0
1090
8.4
1130 10.2
1170 12.0
AVAILABLE
0.8
Rpm Bhp
760
3.6
790
4.6
840
6.0
910
7.9
970 10.0
1040 12.6
1070 13.9
2.0
Rpm Bhp
940
4.6
980
6.0
1020
7.4
1080
9.4
1130 11.4
1.8
Rpm Bhp
930
5.3
960
6.7
1020
8.5
1070 10.5
1120 12.4
1170 15.0
1190 16.2
2.0
Rpm Bhp
970
5.8
1000
7.2
1040
8.9
1090 10.8
1150 13.0
1200 15.5
1.8
Rpm Bhp
940
5.3
990
6.9
1030
8.5
1090 10.3
1140 12.5
2.0
Rpm Bhp
970
5.6
1020
7.3
1060
8.9
1120 10.7
1170 13.0
3.6
Rpm Bhp
1190 7.9
1200 12.5
1.8
Rpm Bhp
910
4.3
950
5.5
990
7.0
1050
8.9
1100 10.9
3.6
Rpm Bhp
1190 8.8
AIRFLOW
(Cfm)
024
6,000
7,000
8,000
9,000
10,000
UNIT
50DK
AIRFLOW
(Cfm)
024
(cont)
6,000
7,000
8,000
9,000
10,000
0.2
Rpm Bhp
640
2.6
710
3.8
770
5.0
850
6.7
920
8.7
0.4
Rpm Bhp
680
2.9
750
4.1
810
5.5
880
7.0
960
9.4
0.6
Rpm Bhp
730
3.3
790
4.5
840
5.8
910
7.5
990 10.1
1.6
Rpm Bhp
910
5.0
960
6.4
1000
8.0
1060
9.9
1120 12.1
2.2
Rpm Bhp
1010
6.0
1050
7.6
1090
9.3
1150 11.2
1200 13.5
2.4
Rpm Bhp
1040
6.5
1080
8.0
1120
9.7
1170 11.7
AVAILABLE
2.6
Rpm Bhp
1070
7.0
1110
8.5
1150 10.1
1200 12.3
3.6
Rpm Bhp
1200 8.8
16
3.4
Rpm Bhp
1170
8.4
AIRFLOW
(Cfm)
028,030
7,000
8,000
9,000
10,000
11,000
12,000
12,500
UNIT
50DK
AIRFLOW
(Cfm)
028,030
(cont)
7,000
8,000
9,000
10,000
11,000
12,000
12,500
0.2
Rpm Bhp
630
3.2
690
4.3
750
5.7
830
7.3
900
9.7
960 12.1
990 13.4
0.4
Rpm Bhp
660
3.4
730
4.7
790
6.0
860
7.8
930 10.2
990 12.7
1020 13.9
0.6
Rpm Bhp
700
3.6
770
5.0
830
6.4
890
8.3
960 10.8
1020 13.3
1050 14.6
2.2
Rpm Bhp
990
6.9
1040
8.6
1070 10.0
1130 12.3
1170 14.8
2.4
Rpm Bhp
1020
7.3
1070
9.0
1100 10.4
1160 12.8
1200 15.3
AVAILABLE
2.6
Rpm Bhp
1050
7.6
1100
9.4
1130 10.9
1180 13.4
AVAILABLE
0.8
Rpm Bhp
740
4.0
810
5.5
860
6.8
920
8.8
990 11.4
1050 14.0
1070 15.2
3.4
Rpm Bhp
1160
9.2
1190 10.9
1.6
Rpm Bhp
890
5.5
950
7.2
990
8.8
1040 10.9
1100 13.3
1160 16.0
1.8
Rpm Bhp
920
5.8
980
7.9
1020
9.3
1070 11.3
1120 13.7
1180 16.6
2.0
Rpm Bhp
960
6.4
1010
8.3
1050
9.7
1100 11.7
1150 14.2
1200 17.0
1.6
Rpm Bhp
900
4.9
950
6.2
1010
8.2
1080 10.2
1140 12.6
1.8
Rpm Bhp
940
5.3
990
6.7
1040
8.5
1110 10.6
1160 13.0
2.0
Rpm Bhp
970
5.7
1020
7.2
1070
8.9
1130 11.0
1190 13.4
1.6
Rpm Bhp
910
5.7
980
7.7
1040
9.6
1110 12.0
1170 14.7
1.8
Rpm Bhp
940
6.1
1010
8.2
1070 10.0
1130 12.4
1200 15.3
2.0
Rpm Bhp
970
6.6
1040
8.6
1100 10.4
1160 12.8
3.6
Rpm Bhp
1190 9.7
AIRFLOW
(Cfm)
024
6,000
7,000
8,000
9,000
10,000
UNIT
50DY
AIRFLOW
(Cfm)
024
(cont)
6,000
7,000
8,000
9,000
10,000
UNIT
50DY
AIRFLOW
(Cfm)
028,030
7,000
8,000
9,000
10,000
11,000
12,000
12,500
UNIT
50DY
AIRFLOW
(Cfm)
028,030
(cont)
7,000
8,000
9,000
10,000
11,000
12,000
12,500
0.6
Rpm Bhp
710
3.2
780
4.4
850
5.9
930
7.9
1000 10.2
0.2
Rpm Bhp
620
2.5
700
3.7
780
5.2
860
6.7
940
9.2
0.4
Rpm Bhp
670
2.9
740
4.0
810
5.6
900
7.3
970
9.6
2.2
Rpm Bhp
1010
6.2
1050
7.6
1100
9.3
1160 11.5
1190 12.0
0.6
Rpm Bhp
740
4.1
820
5.6
880
7.1
960
9.5
1030 12.0
1100 14.9
1130 16.5
AVAILABLE
0.8
Rpm Bhp
780
4.4
860
5.9
910
7.5
990 10.1
1060 12.5
1130 15.6
1160 16.9
0.2
Rpm Bhp
660
3.5
740
4.7
820
6.3
900
8.5
970 11.1
1050 13.9
1070 14.8
0.4
Rpm Bhp
700
3.8
780
5.2
850
6.7
930
9.0
1000 11.6
1080 14.5
1100 15.7
2.2
Rpm Bhp
1000
7.0
1070
8.9
1130 11.0
1190 13.5
3.4
Rpm Bhp
1190 8.8
3.4
Rpm Bhp
1190 9.8
17
6000
7000
8000
CFM
9000
10,000
0.18
0.20
0.25
0.28
0.03
0.03
0.11
0.10
0.15
0.14
0.20
0.09
0.24
0.13
0.28
0.12
0.26
0.11
0.11
50DJ,DK,DW,DY024
POWER EXHAUST FAN PERFORMANCE
18
11,000
12,000
0.32
0.36
0.40
0.16
0.14
0.18
0.15
0.18
0.17
0.19
0.20
0.29
0.14
0.35
0.16
0.41
0.21
0.48
0.25
0.56
0.30
0.33
0.16
0.39
0.18
0.47
0.20
0.58
0.23
0.68
0.30
0.80
0.32
0.33
0.16
0.16
0.41
0.19
0.19
0.49
0.21
0.24
0.58
0.23
0.26
0.68
0.30
0.35
0.80
0.32
0.40
50DJ,DK,DW,DY028,030
POWER EXHAUST FAN PERFORMANCE
Electrical data
UNIT 50DJ,DW024
NOMINAL
V-PH-HZ
208/230-3-60
460-3-60
575-3-60
FLA
Hp
IFM
LRA
VOLTAGE
RANGE
Min
187
414
518
Max
254
508
632
COMPR
NO. 1
RLA
43.3
22.1
17.9
COMPR
NO. 2
LRA
228
114
91
MCA
MOCP
OFM
RLA
RLA
31.5
15.7
12.6
LRA
160
80
64
OFM
Total
FLA
POWER EXHAUST
FAN MOTOR**
IFM
Hp
FLA
5.0*
15.2
7.5*
22.0
5.0
12.4
7.5
19.6
5.0*
7.2
7.5*
10.5
5.0
6.2
7.5
9.8
5.0*
5.6
7.5*
8.6
6.4
3.2
4.8
ELECTRIC
HEAT
POWER SUPPLY
FLA
kW
FLA
MCA
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.4
2.4
2.4
2.4
2.4
2.4
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
18
18
36
36
90
90
18
18
36
36
90
90
18
18
36
36
90
90
18
18
36
36
90
90
36
36
72**
72**
90
36
36
72**
72**
90
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
22.6
22.6
45.2
45.2
113.0
113.0
22.6
22.6
45.2
45.2
113.0
113.0
22.6
22.6
45.2
45.2
113.0
113.0
22.6
22.6
45.2
45.2
113.0
113.0
36.1
36.1
72.3
72.3
90.4
36.1
36.1
72.3
72.3
90.4
108.5-108.5
115.1-114.5
108.5-108.5
115.1-114.5
121.2-132.0
121.2-132.0
223.5-245.2
223.5-245.2
274.6-301.4
115.3-115.3
121.9-121.3
115.3-115.3
121.9-121.3
129.8-140.5
129.8-140.5
232.0-253.8
283.1-309.9
232.0-253.8
105.7-105.7
112.3-111.7
105.7-105.7
112.3-111.7
117.7-128.5
117.7-128.5
220.0-241.7
220.0-241.7
271.1-297.9
112.9-112.9
119.5-118.9
112.9-112.9
119.5-118.9
126.7-137.5
126.7-137.5
229.0-250.7
229.0-250.7
280.1-306.9
53.7
56.7
53.7
56.7
65.5
65.5
150.2
150.2
57.0
60.0
57.0
60.0
69.6
69.6
154.4
154.4
52.7
55.7
52.7
55.7
64.2
64.2
149.0
149.0
56.3
59.3
56.3
59.3
68.7
68.7
153.5
153.5
45.4
47.8
52.1
52.1
97.4
97.4
120.0
48.4
50.8
55.9
55.9
101.1
101.1
123.7
MOCP
Fuse Only
150-150
150-150
150-150
150-150
150-150
150-150
225-250
225-250
300-350
150-150
150-150
150-150
150-150
150-175
150-175
250-300
300-350
250-300
125-125
150-150
125-125
150-150
125-125
150-150
225-250
225-250
300-300
150-150
150-150
150-150
150-150
150-150
150-150
250-300
250-300
300-350
70
70
70
70
70
70
175
175
70
80
70
80
80
80
175
175
70
70
70
70
70
70
150
150
70
80
70
80
80
80
175
175
60
60
60
60
125
125
125
60
60
70
70
125
125
125
*Standard efficiency
High efficiency
**DJ units only
DW units only
19
208/230-3-60
460-3-60
575-3-60
20
VOLTAGE
RANGE
Min
187
414
518
Max
254
508
632
COMPR
NO. 1
RLA
63.6
28.6
22.9
LRA
266
120
96
COMPR
NO. 2
RLA
39.7
19.9
15.9
LRA
198
99
79
OFM
Total
FLA
POWER EXHAUST
FAN MOTOR**
IFM
Hp
FLA
7.5*
22.0
10.0*
26.4
7.5
19.6
10.0
24.2
7.5*
10.5
10.0*
12.5
7.5
9.8
10.0
12.2
7.5*
8.6
10.0*
11.6
10.8
5.4
4.8
ELECTRIC
HEAT
POWER SUPPLY
FLA
kW
FLA
MCA
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
6.6-6.0*
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.4
2.4
2.4
2.4
2.4
2.4
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
15-18
15-18
29-36
29-36
59-72**
59-72**
74-90
18
18
36
36
90**
90**
108
18
18
36
36
90**
90**
108
18
18
36
36
90**
90**
108
18
18
36
36
90**
90**
108
36
36
72**
72**
108
36
36
72**
72**
108
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
22.6
22.6
45.2
45.2
113.0
113.0
135.6
22.6
22.6
45.2
45.2
113.0
113.0
135.6
22.6
22.6
45.2
45.2
113.0
113.0
135.6
22.6
22.6
45.2
45.2
113.0
113.0
135.6
36.1
36.1
72.3
72.3
108.4
36.1
36.1
72.3
72.3
108.4
152.0-152.0
158.6-158.0
152.0-152.0
158.6-158.0
152.0-152.0
158.6-158.0
232.0-253.8
232.0-253.8
283.1-309.9
156.4-156.4
163.0-162.4
156.4-156.4
163.0-162.4
156.4-156.4
163.0-162.4
237.5-259.2
237.5-259.2
288.6-315.4
149.6-149.6
156.2-155.6
149.6-149.6
156.2-155.6
149.6-149.6
156.2-155.6
229.0-250.7
229.0-250.7
280.1-306.9
154.2-154.2
160.8-160.2
154.2-154.2
160.8-160.2
154.2-154.2
160.8-160.2
234.7-256.5
234.7-256.5
285.9-312.6
71.5
74.5
71.5
74.5
71.5
74.5
154.4
154.4
182.6
73.5
76.5
73.5
76.5
73.5
76.5
156.9
156.9
185.1
70.8
73.8
70.8
73.8
70.8
73.8
153.5
153.5
181.7
73.2
76.2
73.2
76.2
73.2
76.2
156.5
156.5
184.7
57.9
60.3
57.9
60.3
101.1
101.1
146.2
60.9
63.3
60.9
63.3
104.9
104.9
150.0
MOCP
Fuse Only
200-200
200-200
200-200
200-200
200-200
200-200
250-300
250-300
300-350
200-200
225-225
200-200
225-225
200-200
225-225
250-300
250-300
300-350
200-200
200-200
200-200
200-200
200-200
200-200
250-300
250-300
300-350
200-200
200-200
200-200
200-200
200-200
200-200
250-300
250-300
300-350
100
100
100
100
100
100
175
175
200
100
100
100
100
100
100
175
175
200
90
100
90
100
90
100
175
175
200
100
100
100
100
100
100
175
175
200
80
80
80
80
125
125
150
80
80
80
80
150
150
150
UNIT 50DJ,DW030
NOMINAL
V-PH-HZ
208/230-3-60
460-3-60
575-3-60
FLA
Hp
IFM
LRA
VOLTAGE
RANGE
Min
187
414
518
Max
254
508
632
COMPR
NO. 1
RLA
63.6
30.0
22.9
COMPR
NO. 2
LRA
266
120
96
MCA
MOCP
OFM
RLA
RLA
44.3
22.1
17.9
LRA
228
114
91
OFM
Total
FLA
POWER EXHAUST
FAN MOTOR**
IFM
Hp
FLA
10.0*
26.4
15.0*
42.0
10.0
24.2
15.0
36.6
10.0*
12.5
15.0*
20.0
10.0
12.2
15.0
18.3
10*
11.6
15*
15.4
10.8
5.4
4.8
ELECTRIC
HEAT
POWER SUPPLY
FLA
kW
FLA
MCA
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-5.0
6.6-6.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.4
2.4
2.4
2.4
2.4
2.4
15
15
29
29
59**
59**
74
15
15
29
29
59**
59**
74
15
15
29
29
59**
59**
74
15
15
29
29
59**
59**
74
18
18
36
36
90**
90**
108
18
18
36
36
90**
90**
108
18
18
36
36
90**
90**
108
18
18
36
36
90**
90**
108
36
36
72**
72**
108
36
36
72**
72**
108
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
40.9- 45.2
40.9- 45.2
81.8- 90.4
81.8- 90.4
163.6-181.0
163.6-181.0
204.5-225.9
22.6
22.6
45.2
45.2
113.0
113.0
135.6
22.6
22.6
45.2
45.2
113.0
113.0
135.6
22.6
22.6
45.2
45.2
113.0
113.0
135.6
22.6
22.6
45.2
45.2
113.0
113.0
135.6
36.1
36.1
72.3
72.3
108.4
36.1
36.1
72.3
72.3
108.4
161.0-161.0
167.6-167.0
161.0-161.0
167.6-167.0
161.0-161.0
167.6-167.0
237.5-259.2
237.5-259.2
288.6-315.4
176.6-176.6
183.2-182.6
176.6-176.6
183.2-182.6
176.6-176.6
183.2-182.6
257.0-278.8
257.0-278.8
308.1-334.9
158.8-158.8
165.4-164.8
158.8-158.8
165.4-164.8
158.8-158.8
165.4-164.8
234.7-256.5
234.7-256.5
285.9-312.6
171.2-171.2
177.8-177.2
171.2-171.2
177.8-177.2
171.2-171.2
177.8-177.2
250.2-272.0
250.2-272.0
301.4-328.1
77.5
80.5
77.5
80.5
77.5
80.5
156.9
156.9
185.1
85.0
88.0
85.0
88.0
85.0
88.0
166.2
166.2
194.5
77.2
80.2
77.2
80.2
77.2
80.2
156.5
156.5
184.7
83.3
86.3
83.3
86.3
83.3
86.3
164.1
164.1
192.4
62.9
65.3
62.9
65.3
104.9
104.9
150.0
66.7
69.1
66.7
69.1
109.6
109.6
154.7
MOCP
Fuse Only
200-200
225-225
200-200
225-225
200-200
225-225
250-300
250-300
300-350
225-225
225-225
225-225
225-225
225-250
225-250
300-300
300-300
350-350
200-200
225-225
200-200
225-225
200-200
225-225
250-300
250-300
300-350
225-225
225-225
225-225
225-225
225-225
225-225
300-300
300-300
350-350
100
110
100
110
100
110
175
175
200
110
110
110
110
125
125
175
175
200
100
110
100
110
100
110
175
175
200
110
110
110
110
110
110
175
175
200
80
80
80
80
150
150
150
80
90
90
90
125
125
175
*Standard efficiency
High efficiency
**DJ units only
DW units only
21
208/230-3-60
460-3-60
575-3-60
22
VOLTAGE
RANGE
Min
187
414
518
Max
254
508
632
COMPR
NO. 1
RLA
43.3
22.1
17.9
LRA
228
114
91
COMPR
NO. 2
RLA
31.5
15.7
12.6
LRA
160
80
64
OFM
Total
FLA
POWER EXHAUST
FAN MOTOR**
IFM
Hp
FLA
5.0*
15.2
7.5*
22.0
5.0
12.4
7.5
19.6
5.0*
7.2
7.5*
10.5
5.0
6.2
7.5
9.8
5.0*
5.6
7.5*
8.6
6.4
3.2
4.8
ELECTRIC
HEAT
POWER SUPPLY
FLA
kW
FLA
MCA
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.4
2.4
2.4
2.4
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
18
18
36
36
18
18
36
36
18
18
36
36
18
18
36
36
36
36
36
36
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
36.1
36.1
36.1
36.1
108.5-108.5
115.1-114.5
108.5-108.5
115.1-114.5
121.2-132.0
121.2-132.0
115.3-115.3
121.9-121.3
115.3-115.3
121.9-121.3
129.8-140.5
129.8-140.5
105.7-105.7
112.3-111.7
105.7-105.7
112.3-111.7
117.7-128.5
117.7-128.5
112.9-112.9
119.5-118.9
112.9-112.9
119.5-118.9
126.7-137.5
126.7-137.5
53.7
56.7
53.7
56.7
65.5
65.5
57.0
60.0
57.0
60.0
69.6
69.6
52.7
55.7
52.7
55.7
64.2
64.2
56.3
59.3
56.3
59.3
68.7
68.7
45.4
47.8
52.1
52.1
48.4
50.8
55.9
55.9
MOCP
Fuse Only
150-150
150-150
150-150
150-150
150-150
150-150
150-150
150-150
150-150
150-150
150-175
150-175
125-125
150-150
125-125
150-150
125-125
150-150
150-150
150-150
150-150
150-150
150-150
150-150
70
70
70
70
70
70
70
80
70
80
80
80
70
70
70
70
70
70
70
80
70
80
80
80
60
60
60
60
60
60
70
70
UNIT 50DK,DY028
NOMINAL
V-PH-HZ
208/230-3-60
460-3-60
575-3-60
FLA
Hp
IFM
LRA
VOLTAGE
RANGE
Min
187
414
518
Max
254
508
632
COMPR
NO. 1
RLA
63.6
28.6
COMPR
NO. 2
LRA
266
120
22.9
MCA
MOCP
OFM
RLA
96
RLA
39.7
19.9
15.9
LRA
198
99
79
OFM
Total
FLA
POWER EXHAUST
FAN MOTOR**
IFM
Hp
FLA
7.5*
22.0
10.0*
26.4
7.5
19.6
10.0
24.2
7.5*
10.5
10.0*
12.5
7.5
9.8
10.0
12.2
7.5*
8.6
10.0*
11.6
10.8
5.4
4.8
ELECTRIC
HEAT
POWER SUPPLY
FLA
kW
FLA
MCA
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.4
2.4
2.4
2.4
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
18
18
36
36
18
18
36
36
18
18
36
36
18
18
36
36
36
36
36
36
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
36.1
36.1
36.1
36.1
152.0-152.0
158.6-158.0
152.0-152.0
158.6-158.0
152.0-152.0
158.6-158.0
156.4-156.4
163.0-162.4
156.4-156.4
163.0-162.4
156.4-156.4
163.0-162.4
149.6-149.6
156.2-155.6
149.6-149.6
156.2-155.6
149.6-149.6
156.2-155.6
154.2-154.2
160.8-160.2
154.2-154.2
160.8-160.2
154.2-154.2
160.8-160.2
71.5
74.5
71.5
74.5
71.5
74.5
73.5
76.5
73.5
76.5
73.5
76.5
70.8
73.8
70.8
73.8
70.8
73.8
73.2
76.2
73.2
76.2
73.2
76.2
57.9
60.3
57.9
60.3
60.9
63.3
60.9
63.3
MOCP
Fuse Only
200-200
200-200
200-200
200-200
200-200
200-200
200-200
225-225
200-200
225-225
200-200
225-225
200-200
200-200
200-200
200-200
200-200
200-200
200-200
200-200
200-200
200-200
200-200
200-200
100
100
100
100
100
100
100
100
100
100
100
100
90
100
90
100
90
100
100
100
100
100
100
100
80
80
80
80
80
80
80
80
*Standard efficiency
High efficiency
**DJ units only
DW units only
23
208/230-3-60
460-3-60
575-3-60
FLA
Hp
IFM
LRA
VOLTAGE
RANGE
Min
187
414
518
Max
254
508
632
COMPR
NO. 1
RLA
63.6
30.0
COMPR
NO. 2
LRA
266
120
22.9
MCA
MOCP
OFM
RLA
96
RLA
44.3
22.1
17.9
LRA
228
114
91
OFM
Total
FLA
POWER EXHAUST
FAN MOTOR**
IFM
Hp
FLA
10.0*
26.4
15.0*
42.0
10.0
24.2
15.0
36.6
10.0*
12.5
15.0*
20.0
10.0
12.2
15.0
18.3
10*
11.6
15*
15.4
10.8
5.4
4.8
ELECTRIC
HEAT
POWER SUPPLY
FLA
kW
FLA
MCA
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
6.6-6.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.4
2.4
2.4
2.4
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
15-18
15-18
29-36
29-36
18
18
36
36
18
18
36
36
18
18
36
36
18
18
36
36
36
36
36
36
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
40.9-45.2
40.9-45.2
81.8-90.4
81.8-90.4
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
22.6
22.6
45.2
45.2
36.1
36.1
36.1
36.1
161.0-161.0
167.6-167.0
161.0-161.0
167.6-167.0
161.0-161.0
167.6-167.0
176.6-176.6
183.2-182.6
176.6-176.6
183.2-182.6
176.6-176.6
183.2-182.6
158.8-158.8
165.4-164.8
158.8-158.8
165.4-164.8
158.8-158.8
165.4-164.8
171.2-171.2
177.8-177.2
171.2-171.2
177.8-177.2
171.2-171.2
177.8-177.2
77.5
80.5
77.5
80.5
77.5
80.5
85.0
88.0
85.0
88.0
85.0
88.0
77.2
80.2
77.2
80.2
77.2
80.2
83.3
86.3
83.3
86.3
83.3
86.3
62.9
65.3
62.9
65.3
66.7
69.1
66.7
69.1
*Standard efficiency
High efficiency
**DK units only
24
MOCP
Fuse Only
200-200
225-225
200-200
225-225
200-200
225-225
225-225
225-225
225-225
225-225
225-250
225-250
200-200
225-225
200-200
225-225
200-200
225-225
225-225
225-225
225-225
225-225
225-225
225-225
100
110
100
110
100
110
110
110
110
110
125
125
100
110
100
110
100
110
110
110
110
110
110
110
80
80
80
80
80
90
90
90
LEGEND
EQUIP Equipment
GND
Ground
NEC
National Electrical Code
25
LEGEND
HIR Heating Interlock Relay
NOTES:
1. SW1 Field-Supplied Switch (or Time Clock) used to move unit
in and out of the occupied mode.
2. If unit has heat, field must wire between terminals 8 and 9 or 8
and 15 and supply power source to drive room terminals wide
open during heating.
3. Night Thermostat Field-supplied thermostat which can be used
to keep building from becoming too hot or too cold when unit is in
the unoccupied mode.
4. Single-step demand limit consists of a field-supplied 5-20 K-ohm
potentiometer wired to TB2 as shown.
5. If temperature reset is used, thermistor T10 must be wired in series with potentiometer P7 (located on the reset board) and wired
to TB2 as shown. T10 and the reset board are included in accessory package 50DJ900021.
6.
Factory Wiring
Field Wiring
7. Contact ratings for HIR relay (HN61KL013) 125 va pilot duty
at 125/250 volt.
26
BUILDING PRESSURIZATION
Switch 1
Switch 2
Switch 3 (if unit equipped with power exhaust)
Switch 5
Switch 6
SMOKE PURGE
Switch 1
Switch 3
Switch 4
Switch 5
Switch 6
LEGEND
DPS
ECR
HIR
IFC
MPE
BUILDING PRESSURIZATION
Switch 2
Switch 3
Switch 6
Switch 7
Switch 8
Switch 9
Switch 11
Switch 11a
SMOKE PURGE
Switch 2
Switch 4
Switch 6
Switch 7
Switch 8
Switch 10
Switch 11
Switch 11a
economizer opens
exhaust fan running
exhaust dampers are open
supply fan is not running
The above wiring information shows what electrical connections and switches are required to enable smoke purge
and building pressurization. Note that the optional economizer is required for both functions and the power exhaust
is required for smoke purge.
There are 115-v terminals (TB3 Terminals 4 and 8 VAV,
TB2 Terminals 4 and 5 CV) available for powering field installed smoke detectors. The maximum available va during
smoke detector standby mode is 10 va, and 45 va during
alarm mode.
Note that is is possible to remotely energize the power
exhaust fan using the power exhaust contacts. This would
allow smoke removal to occur without a fireman having to
climb onto the roof before structural integrity can be
verified.
27
Controls
Operating sequences, constant volume units
(50DJ,DW)
Cooling, units without economizer Unit power ON,
system selector switch at COOL or AUTO., fan switch at
AUTO.; thermostat at setting below room temperature:
Y1 on the thermostat subbase closes, energizing compressor no. 1 as first stage of cooling. (Compressor no. 1 is
always the larger of the 2 unit compressors.) If cooling load
cannot be satisfied with only first-stage cooling, Y2 on the
thermostat will close, energizing compressor no. 2.
Condenser fans are energized with compressor no. 1.
The no. 1 fan runs continuously while the unit is on mechanical cooling; the no. 2 fan is cycled on and off for head
pressure control. Check cooling effects at a setting above
room temperature. Compressors will shut off.
Heating, units without economizer Unit power ON,
system selector switch at HEAT, fan switch at AUTO.; thermostat at setting above room temperature:
When W1 on the thermostat closes, the first stage of electric heat is energized. On a further drop in room temperature, W2 on the thermostat closes, energizing the second
stage of electric heat.
NOTE: Units equipped with low electric heat option have
only one stage. Reset thermostat to a setting below room
temperature. Unit should shut off.
Cooling, units with economizer With subbase switch
set at COOL and fan switch set at AUTO., indoor fan is
energized when Y1 on thermostat closes. If enthalpy is below setting on enthalpy switch, the economizer outside air
dampers will modulate open to satisfy the cooling requirement. If outside air alone will not meet the cooling requirements, Y2 on the thermostat will close, energizing compressor no. 1 to work in conjunction with the modulating
economizer to meet the cooling requirement. While the unit
is operating using outside air, compressor no. 2 cannot be
energized. If enthalpy is above setting on enthalpy switch,
the economizer outside air dampers move to the minimum
(ventilation) position, and condenser fans numbers 1 and 2
cycle on and off as described in Cooling, units without economizer.
NOTE: If fan switch is ON and the room thermostat is
satisfied, the outside air dampers move to the minimum
position.
Heating, units with economizer Operation is the same
as described in Heating, units without economizer, except
that the outside air dampers move to the minimum position.
28
During initialization period, effective range of economizer potentiometer P2 is established and is used to sense
position of economizer dampers. For approximately 60 seconds of initialization period, dampers are driven fully open
and full open resistance of potentiometer is recorded by
microprocessor. The dampers are then driven to fully closed
position and this potentiometer resistance is also recorded
by microprocessor. These 2 readings establish effective range
of the economizer potentiometer.
Upon completion of initialization mode, the control operates unit to try to maintain the temperature at setting of
the cold temperature set point (mounted on the display
board). This is potentiometer P1. The control will always
try to useeconomizer as first stage of cooling, enthalpy permitting. Enthalpy permitting, control will open economizer
dampers and try to maintain leaving air temperature at the
cold temperature set point minus 2. If economizer dampers become fully open and still cannot maintain desired leaving air temperature, control will begin to cycle on compressors and condenser fans. Once mechanical cooling begins,
control strives to maintain leaving air temperature at cold
temperature set point rather than at the cold temperature
set point minus 2.
The microprocessor determines how rapidly capacity steps
are added or subtracted based on deviation from leaving air
set point and rate of change of leaving air temperature.
If enthalpy is such that economizer cannot be used for
cooling, dampers will go to their minimum position as set
by potentiometer P5 (located on accessory board). The control will then use mechanical cooling to meet the cooling
load.
Units with morning warm-up heat (optional electric
heat), heating When in heating mode, room terminals
must be wide open.
Dip switch 4 (located on the processor board) must be in
ON position.
If return-air temperature (T2) is 5 below warm-up temperature set point P6 (located on the accessory board), heating relay will be energized and heat will be brought on and
will run until return-air temperature is above 2 below setting on P6. During heating, economizer dampers will be
fully closed. The unit can go in and out of heating until
return-air temperature rises above the setting on P6. After
the return-air temperature rises above the warm-up set point,
unit cannot go back into heating mode until unit re-enters
occupied mode.
Units equipped with space temperature reset Unit
operates exactly like a unit without reset until reset is used.
When unit is operating in reset mode, a code of 21 will
appear on display when display button is pushed; this means
that control is controlling to a leaving air set point different
than that set using P1.
Units equipped with demand limit Unit operates exactly like standard VAV units until demand limiting takes effect and limits amount of compression that will be allowed
to be brought on.
50DW
Application data
Condensate removal
When units are mounted on roof curbs, use the factoryprovided condensate drain connections provided in the unit
base rail. Condensate drain openings are provided on the
air-handling end of the unit to allow proper drainage. When
units are mounted on concrete slabs, condensate drain openings must be drilled in the vertical face of the baserail, as
29
Factory Wiring
Field Wiring
Factory Wiring
Field Wiring
30
Guide specifications
50DJ,DW constant volume units
Packaged Rooftop Cooling Unit
With Electric Heat Constant Volume
Application
HVAC Guide Specifications
Size Range: 20 to 27 Tons, Nominal
Carrier Model Number: 50DJ (Downflow)
50DW (Horizontal)
NOTE: Items throughout the specification which apply only
to With Electric Heat are indicated by single brackets [i.e.].
Part 1 General
1.01 SYSTEM DESCRIPTION
A. Outdoor rooftop mounted, electronically controlled
cooling unit with heating option utilizing semi-hermetic
type reciprocating compressors for cooling duty and
[electric resistance] for heating duty. Unit shall discharge supply air downward or horizontally as shown
on contract drawings.
1.02 QUALITY ASSURANCE
A. Unit shall be rated in accordance with ARI Standards
360 and 270.
B. Unit shall be designed to conform to UL Standards 465.
C. Unit shall be ETL listed and CSA certified as a total
package for safety requirements.
D. Roof curb shall be designed to conform to NRCA
Standards.
E. Insulation and adhesive shall meet NFPA 90A requirements for flame spread and smoke generation.
F. Unit casing shall be capable of withstanding Federal
test method Standard No. 141 (Method 6061) 500
hour salt spray test.
G. Evaporator and condenser coils shall be leak tested
at 150 psig (1034 kPa) and pressure tested at 450
psig (3103 kPa).
1.03 DELIVERY, STORAGE AND HANDLING
A. Unit shall be stored and handled per manufacturers
recommendations.
Part 2 Products
2.01 EQUIPMENT
A. General:
Factory-assembled, single-piece, cooling unit with heating option. Contained within the unit enclosure shall
be all factory wiring, piping, controls, refrigerant charge
(R-22), and special features required prior to field
start-up.
B. Unit Cabinet:
1. Unit cabinet shall be constructed of galvanized steel,
bonderized and coated with a baked enamel
finish.
2. Cabinet panels shall be hinged for easy servicing.
3. Lifting lugs shall be factory installed to facilitate
overhead rigging.
4. Unit shall be equipped with factory-supplied condensate drain connection for evaporator coil.
C. Fans:
1. The single indoor blower (evaporator fan) shall be
of the forward curved centrifugal belt driven type
only, with fixed pitch pulley drive.
2. Outdoor (condensing) fans shall discharge air vertically upward and shall have permanently lubricated bearings.
3. Outdoor (condensing) fans shall be of the direct
driven propeller type only and be protected by a
coated steel wire guard.
4. Indoor blower (evaporator fan) shaft bearings
shall be of the ball bearing type with lubrication
provisions.
D. Compressors:
1. Two semi-hermetic type with unloading
capability.
2. Factory mounted on spring vibration isolators.
3. Equipped with a factory-installed crankcase heater
to minimize liquid refrigerant accumulation in compressor during shutdown and prevent refrigerant
dilution of oil.
E. Coils:
1. Evaporator and condenser coils shall have aluminum plate fins mechanically bonded to seamless
copper tubes with all joints brazed.
2. Tube sheet openings to be belled to prevent tube
wear.
3. Evaporator coil shall be of the full face active
design.
4. Coils shall be intertwined circuited to provide 2
independent refrigeration systems.
F. Heating Section:
1. Factory-installed electric resistance heater(s) of the
characteristics shown in the equipment schedule.
2. Heater elements shall be open wire type,
adequately supported and insulated with ceramic
bushings.
G. Refrigerant Components:
Refrigerant circuit components shall include: filter driers, liquid line sight glasses, compressor discharge
valves, liquid line service valves and thermal expansion valves.
H. Filter Section:
1. Standard filter section shall consist of low velocity
disposable 2-in. thick fiberglass filters in commercially available sizes.
2. Filter face velocity shall not exceed 400 fpm at
nominal airflows.
I. Controls and Safeties:
1. Unit Controls:
a. Unit shall be complete with self-contained,
demand-oriented solid state control system.
b. Unit staging shall be minimum 2-cool, 2-heat
(one-heat on low heat package only).
c. Unit shall perform in response to a variable
space temperature signal.
31
Guide specifications
50DJ,DW constant volume units (cont)
d.
J.
K.
L.
M.
32
2.
3.
4.
5.
6.
7.
8.
9.
33
Guide specifications
50DK,DY variable air volume units
Packaged Rooftop Cooling Unit
With Electric Heat Variable Volume
Application
C.
34
D.
E.
F.
G.
H.
4. Unit shall be equipped with factory-supplied condensate drain connection for evaporator coil.
Fans:
1. The single indoor blower (evaporator fan) shall be
of the forward curved centrifugal belt driven type
only, with fixed pitch pulley drive (with optional
factory-installed inlet guide vanes and controls).
2. Outdoor (condensing) fans shall discharge air vertically upward and shall have permanently lubricated bearings.
3. Outdoor (condensing) fans shall be of the direct
driven propeller type only and be protected by a
coated steel wire guard.
4. Indoor blower (evaporator fan) shaft bearings shall
be of the ball bearing type with lubrication
provisions.
Compressors:
1. Two semi-hermetic type with unloading capability.
2. Factory mounted on spring vibration isolators.
3. Equipped with a factory-installed crankcase heater
to minimize liquid refrigerant accumulation in compressor during shutdown and prevent refrigerant
dilution of oil.
Coils:
1. Evaporator and condenser coils shall have aluminum plate fins mechanically bonded to seamless
copper tubes with all joints brazed.
2. Tube sheet openings to be belled to prevent tube
wear.
3. Evaporator coil shall be of the full face active
design.
4. Coils shall be intertwined circuited to provide 2
independent refrigeration systems.
[Heating Section:]
1. Factory-installed electric resistance heater(s) of the
characteristics shown in the equipment schedule.
2. Heater elements shall be open wire type, adequately
supported
and
insulated
with
ceramic
bushings.
3. Heater is single stage for morning warm-up only.
Refrigerant Components:
Refrigerant circuit components shall include: filter driers, liquid line sight glasses, compressor discharge
valves, liquid line service valves and thermal expansion valves.
Filter Section:
1. Standard filter section shall consist of low-velocity,
disposable 2-in. thick fiberglass filters in commercially available sizes.
2. Filter face velocity shall not exceed 400 fpm at
nominal airflows.
J.
K.
L.
M.
3. Diagnostics:
a. Diagnostic display module shall be capable of
indicating a safety lockout condition through
displaying a 2-digit code for which a legend
shall be provided in the control panel.
b. Diagnostic module must also be capable of
displaying outputs of microprocessor controlled run test to verify operating of every
switch, thermistor, potentiometer, fan and
compressor before unit is started.
Operating Characteristics:
1. Unit shall be capable of starting and running at
115 F ambient outdoor temperature per maximum load criteria of ARI Standard 360.
2. Compressor with standard controls shall be capable of operation down to 45 F ambient outdoor
temperature.
3. Provides multi-stage mechanical cooling capability.
4. Unit shall be factory equipped with hot gas bypass
valve, shutoff valve and tubing to maintain capacity control at minimum cooling loads.
Electrical Requirements:
All unit power wiring shall enter unit cabinet at a
single location, either through side or bottom (curb
opening).
Motors:
1. Compressor motors shall be cooled by suction gas
passing through motor windings and shall have internal thermal overload protection.
2. Indoor blower poly-phase motor bearings shall be
of the ball bearing type.
3. Outdoor totally enclosed motors shall have permanently lubricated sealed ball bearings and inherent automatic reset thermal overload protection.
4. Each poly-phase compressor and indoor fan motor shall be protected against overcurrent and single
phasing conditions. Protection devices shall be
manual reset type.
Special Features:
Certain standard features are not applicable when the
features designated * are specified. For assistance in
amending the specifications, your local Carrier Sales
Office should be contacted.
1. Integrated Economizer:
Enthalpy controlled integrated type consisting of
dampers, motors and linkages, and potentiometer in conjunction with control system to provide primary cooling using outdoor air, enthalpy
permitting, supplemented with mechanical cooling when necessary.
a. Dampers shall be low leakage type, not to
exceed 1% leakage at 1.0 in. wg pressure
differential when fully closed.
b. Linkages shall have a spring return feature
which shuts dampers upon a power interruption or unit shutdown.
35
Guide specifications
50DK,DY variable air volume units (cont)
2.
3.
4.
5.
6.
7.
296
3-92
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book 1
Tab 1b
Page 36
Printed in U.S.A.
PC 111
Form 50DJ,DK-5PD
Replaces: 50DJ,DK-3PD