, heating
, ventilating
, auto
, med
, high
changeover
and
; mode
Function :
Detect and Display room temperature
Timing sleep
Order Guide:
Model
Floating
Output
signal
EXT-HA8102A
Cooling/Heating
EXT-HA8102AN
Cooling/Heating
EXT-HA8102B
Modulation
Fan
RS485
Input
Remote
(Single/3-speed)
Network
Control
Sensor
Cooling/Heating
EXT-HA8102BN
Cooling/Heating
EXT-HA8102C
Cooling/Heating
EXT-HA8102CN
Cooling/Heating
EXT-HA8102D
Cooling/Heating
EXT-HA8102DN
Cooling/Heating
Cooling
Heating
EXT-HA8102EN
Cooling
Heating
EXT-HA8102F
Heating
Cooling
EXT-HA8102FN
Heating
Cooling
EXT-HA8102E
EXT-HA8102I
Cooling&Heating
EXT-HA8102IN
Cooling&Heating
EXT-HA8102K
Cooling&Heating
EXT-HA8102KN
Cooling&Heating
Fan: thermostat with fan functions, can be selected with single speed fan or three speed fan by setting parameter.
Remote Control: input signal can be selected by setting parameter.
Specification :
Power:
AC 24V10
Accuracy displayed:
0.1
Output signal:
Accuracy:
0.5
Input signal:
Rated Power:
<1W
Dimensions:
868623mm (WHD)
Sensor type:
NTC
Display:
LCD
Page 1 of 4
50Hz/60Hz
Operations:
On/Off: Press
, the setpoint will be confirmed automatically after 5 seconds, and then return to dispay status, press
0.5
check setpoint.
Mode: With thermostat on, press
Heating
, Vent "
or
to
", Auto
, Med speed
, High speed
Under auto speed fan, the fan speed will be changed automatically as below: in low speed when room temperature is
1 difference with setpoint;in med speed when room temperature is 2 difference with setpoint; in High speed when
room temperature is 3 difference with setpoint.
Sleep: Thermostat will get into sleep function after programming.The set Temperature should to be.
To set
Press
button for 3 seconds till display, theres a number of count down in the center of LCD, Use
or
to adjust the desired sleep time: the max. = 48 hours; thermostat will return to the working status after 5
seconds, is flashing to start counting down. The setpoint should be replaced by the sleep setpoint.
To quit: When thermostat get into Sleep function, will flash, press
Keypad lock: press
Press
and
and
or
to quit.
for 10 seconds till to display to activate, under this function, any keypad is locked.
Parameter table
Paramete
Description
Default
Range
0-2
0-1
Step
0-1
Temperature calibration
0-1
-20.0 20.0
0.1
6
7
Minimum setpoint
0 - 99.5
0.5
Maximum setpoint
35
10
11
28
12
Comms# (EXT-HA8102XN)
/41
/96
2
/45
/82
0.1
0 - 99.5
0.5
0 - 10
0.5
0 - 99.5
0.5
0 - 99.5
0.5
1 - 32
0-3
14
90 sec.
10 - 300 sec.
10 sec.
15
90 sec.
10 - 300 sec.
10 sec.
16
0-1
17
0-2
18
0-1
Page 2 of 4
19
0Bit
0-128Bit(5V/10mA)
0.04V/Bit(0.08mA/Bit)
20
1 - 20
0.5
21
0-1
22
0 Bit
0-128Bit(5V/10mA)
0.04V/Bit(0.08mA/Bit)
23
1 - 20
0.5
24
1 sec.
1 - 9 sec.
1 sec.
25
30 sec.
10 - 300 sec.
10 sec.
26
1 sec.
1-9 sec.
1 sec.
27
30 sec.
10 - 300 sec.
10 sec.
28
0-1
( 0: Disable; 1: Enable )
Override output value when bypass PID control
29
0 - 255
30
0 - 255
31
0: Input valid
1: Override Input: open
0-2
0-1
0-3
32
33
N/A
/42
/46
/42-62
/46-66
0-15
2-17
/2
/2
It will confirm itself 20 seconds later after setting and return to Off state.
ON
OFF
Off
Off
Off
Off
Mounting:
screwdriver.
diagram.
Page 3 of 4
Wiring diagram:
Note: Be sure to connect all the wires as per the wiring diagrams and keep it away from water,
mud and other material so as to prevent the unit being spoiled!
.
Page 4 of 4