For
(Project Name)
The Hydraulic Analysis Report for (Project name) dated (Date); has been completed by (Engineers
Name) for (Owner/Developers Name). This report is prepared in compliance with existing City Code,
Utility Tariffs, and the latest revision of the Colorado Springs Utilities Water Line Extension and
Service Standards.
This Report does not reserve capacity in the water system until a building permit is obtained.
Significant changes to the development plan will require an addendum to this Report.
Submitting Engineer
______________________________
Colorado P.E. #
Date: ________________
______________________________
________________________________
Date: ________________
7/5/2016
Date: __________________
Page 1 of 12
Number of Units:
Number of Units:
Number of Units:
Number of Units:
Number of Units:
Acres:
Acres:
Acres:
Acres:
Acres:
Acres:
Acres:
Acres:
Acres:
GPM@ 20 psi
GPD
Comments:
Attach a site map with water main alignment and proposed connection points and email map and form to:
waterplanning@csu.org or fax to (719)668-2729.
7/5/2016
Page 2 of 12
Company:
Email:
Developer:
Existing System Notes: Please note that for pressures 170 psi or greater, DIP is required.
Water Quality Notes:
7/5/2016
Page 3 of 12
Site
Site map showing potential connection points
Please verify fire flow requirements w/ CSFD prior to Construction Drawing submittal. At the time the
Construction Drawings are submitted to UDS, please also submit UDCF through DDS, and notify WPD of
UDCF Receipt number, along with hydrant flange elevations and required fire flows.
mwetzig@csu.org | www.csu.org
Page 4 of 12
Project Number:
Map Page(s):
Company:
Email:
Developer:
HGL Information
Pressure Zone(s):
HGL at Max Day Demand (lowest system pressure):
HGL at Min Day Demand (maximum system pressure):
Max Day to Average Day (MD/AD) peaking factor:
Available Fire Flow at Existing Hydrant near Site as Reference
Hydrant Number:
Hydrant Flange elevation:
Hydrant Location:
Theoretical Available Fire Flow at 20 psi residual:
Pressure at max day demands:
*The Fire Flow information above is provided solely as a reference. An official Fire Flow report must be requested by the engineer
and provided by Colorado Springs Utilities Water Planning prior to sign off of construction plans by Colorado Springs Utilities and
Colorado Springs Fire Department.
Looping Requirements: A minimum of 2 connections are needed for looping, for redundancy and water
quality purposes.
Existing System Notes: Please note that for pressures 170 psi or greater, DIP is required.
Melissa Wetzig, P.E.
719.668.8741
Water Planning & Design
mwetzig@csu.org | www.csu.org
7/5/2016
Page 5 of 12
Demand Table
Planni
ng
Area
Bld
#
Use
Units
Acre
s
Bld Sq
Ft
Construc
tion Type
Sprink
led
Fire
Flow
(gpm
)
Avg
Deman
d
Factor
(gpd)
Totals
Note: Fire flow demands should be verified by CSFD or a conservative
estimate should be used
7/5/2016
Page 6 of 12
Avg
Deman
d
(mgd)
Peaki
ng
Facto
r
Max
Day
Dema
nd
(mgd)
Max
Day
Dema
nd
(gpm)
Node Table
Node
7/5/2016
Elevati
on
(feet)
Max
Day
Dema
nd
(gpm)
Page 7 of 12
Pipe Table
Pipe
ID
Lengt
h
Diame
ter
Roughn
ess
Site Map
7/5/2016
Page 8 of 12
Network Map
7/5/2016
Page 9 of 12
7/5/2016
Page 10 of 12
Summary Table
Planni
ng
Area
Phas
e
Range of
Max Day
Demand
(gpm)
Range of
Required
Fire Flow
(gpm)
Range of Max
Fire Flow (gpm)
Recover
y
Applica
ble?
Output File
7/5/2016
Page 11 of 12
Oversi
zed
Main?