20 MHz to 5 GHz
4 to 35 VOLTS, PRF to 1 MHz
MONOCYCLE GENERATORS
500 ps/div
T1
200 ps/div
AVC-C
20 V/div, 10 ns/div
100 ps/div
AVA-C
10 V/div, 2 ns/div
AVE2-C-5000, 5 V/div
Avtech offers a unique line of tunable and fixed-tuned highpower solid-state VHF and UHF monocycle generators for
ultrasonic, SAW, radar (including ground penetrating radar),
TDR and network characterization applications. The frequency
tuning option, small size, and high output power permit many
novel applications. Units in the frequency range of 200 to 5000
MHz produce a single sinusoid output while units in the range
of 20 to 200 MHz produce a more rectangular doublet, as
shown in the photos above.
The AVD1 and AVD families are both fixed-tuned units for the
frequency range of 400 to 1500 MHz, but the AVD1 modules
are much smaller (1.1" x 1.3" x 2.3") than the AVD modules
(1.7" x 2.6" x 4.2"). The fixed-tuned AVE family operates in the
frequency range of 1500 to 3000 MHz. The AVE1 family
features octave tuning (via a one-turn control) in the frequency
range of 1000 to 3000 MHz while the new AVE2 family
provides fixed-tuned units in the frequency range of 3000 to
5000 MHz. Models AVA and AVB both operate in the frequency
range of 200 to 400 MHz but the AVA is tunable over the full
octave while the AVB is fixed-tuned. Frequency tuning of Model
AVA is accomplished by varying the length of a miniature
flexible coaxial cable between two SMA connectors. The AVC
Model:
Center frequency:
(MHz)
Amplitude: (Vpp, 506)
PRFmax (MHz):
Spurious signals:
Propagation delay:
Jitter:
DC offset option4:
Monitor output option7:
Trigger required:
Sync delay:
Sync output: (-C only)
Connectors:
Power requirement:
Dimensions
-C:
(H x W x D) Modules:
Chassis material:
Temperature range:
AVD1-C1
AVD1
400-1500
fixed-tuned2
20 VPP
AVD-C1
AVD
400-1500
fixed-tuned2
20 VPP3
1 MHz
1 MHz3
AVE-C1
AVE
1500-3000
fixed-tuned2
10 VPP
AVE1-C1
AVE2-C1
AVE1
AVE2
1200-3000
3000-5000
octave tuning5,8 fixed-tuned2
10 VPP
4 VPP
1 MHz
AVA-C1
AVA
200-400
tunes full range
20 VPP
AVB-C1
AVB
200-400
fixed-tuned2
20 VPP
AVC-C1
AVC
20-200
T1:2.5-25 ns2
35 VPP
1.0 for T1 = 2.5ns
0.1 for T1 = 25 ns
1) -C suffix indicates stand-alone lab instrument with internal clock and line powering.
No suffix indicates miniature module requiring DC power and external trigger. (See
http://www.avtechpulse.com/formats for details of the basic instrument formats).
2) Specify required frequency (or T1).
3) The maximum PRF for AVD units above 1000 MHz can be extended to 3 MHz. To
specify this option add the suffix -F3 to the model number. The maximum output
amplitude at 1 - 3 MHz falls to 15 VPP.
4) For DC offset option suffix model number with -OS. Not available on AVE2 models.
Avtech Model AVX-T bias tee can also be used to obtain DC offset.
AVD1
AVD
5) When ordering, specify the octave tuning range by adding a suffix consisting of the
lower and upper center frequencies, i.e. add suffix -1000-2000 to specify a 10002000 MHz tuning range, or -1500-3000 to specify a 1500-3000 MHz tuning range.
6) A 50 Ohm load is required. Other loads may damage the instrument. Consult Avtech
(info@avtechpulse.com) if you need to drive other load impedances.
7) For monitor option add suffix -M. Not available on AVE2 models.
8) For electronic control (0 to +10V) of the center frequency, suffix the model number
with -EF. Electronic control units also include the standard front panel one-turn
controls. Input impedance greater than 10 kilohms.
AVA