SERVICE MANUAL
MODEL: GSA-4165B/
GSA-4167B/
GSA-4168B
P/NO : 3828HS1047G
August 2005
Printed in Korea
MODEL : GSA-4165B/GSA-4167B/GSA-4168B
TABLE OF CONTENTS
INTRODUCTION .......................................................................................................................................................................3
FEATURES............................................................................................................................................................................3~5
SPECIFICATIONS.................................................................................................................................................................6~9
LOCATION OF CUSTOMER CONTROLS .......................................................................................................................10~11
DISASSEMBLY .................................................................................................................................................................12~13
1. CABINET and CIRCUIT BOARD DISASSEMBLY ..........................................................................................................12
1-1. Bottom Chassis ..........................................................................................................................................................12
1-2. Front Bezel Assy ........................................................................................................................................................12
1-3. Cabinet and Main Circuit Board .................................................................................................................................12
2. MECHANISM ASSY DISASSEMBLY..............................................................................................................................12
2-1. Pick-up Unit................................................................................................................................................................12
2-2. Pick-up ......................................................................................................................................................................13
EXPLODED VIEW .............................................................................................................................................................14~15
MECHANICAL REPLACEMENT PARTS LIST ................................................................................................................16~18
GLOSSARY .............................................................................................................................................................................19
THE DIFFERENCES OF CD-R/CD-RW DISCS AND GENERAL CD-ROM.....................................................................20~26
1. Recording Layer ..............................................................................................................................................................20
2. Disc Specification ............................................................................................................................................................20
3. Disc Materials ..................................................................................................................................................................21
4. Reading Process of Optical Disc .....................................................................................................................................22
5. Writing Process of CD-R Disc .........................................................................................................................................23
6. Writing Process of CD-RW Disc ......................................................................................................................................23
7. Organization of the PCA, PMA and Lead-in Area ...........................................................................................................24
8. Function of PCA and PMA area ......................................................................................................................................25
9. OPC and ROPC ..............................................................................................................................................................25
10. Writing Process of DISC................................................................................................................................................26
THE DIFFERENCES OF DVD-R/RW, DVD+R/RW DISCS AND DVD-ROM....................................................................27~35
1. Recording Layer ..............................................................................................................................................................27
2. Disc Specification ............................................................................................................................................................28
3. Disc Materials ..................................................................................................................................................................28
4. Writing Pulse Waveform of DVD+R.................................................................................................................................31
5. Writing Pulse Waveform DVD+RW .................................................................................................................................33
6. Organization of Inner Drive Area, Outer Drive Area, Lead-in Zone and Lead-out Zone .................................................34
LightScribe MEDIA...........................................................................................................................................................36~39
1. LightScribe Media............................................................................................................................................................36
2. Hardware Block Diagram of LightScribe Label Printing...................................................................................................37
3. MD Assy For LightScribe.................................................................................................................................................38
4. Optical Encoder Assy ......................................................................................................................................................39
DVD & CD DATA PROCESSING......................................................................................................................................40~43
1. Data Processing Flow......................................................................................................................................................40
2. Copy Protection and Regional Code Management Block ...............................................................................................41
3. About Prevention the DVD-ROM from to be copy ...........................................................................................................42
4. About the DVD-ROM Regional Code ..............................................................................................................................43
INTERNAL STRUCTURE OF THE PICK-UP....................................................................................................................44~46
1. Block Diagram of the Pick-up(HOP-7632TS) ..................................................................................................................44
2. Pick up Pin Assignment...................................................................................................................................................45
3. Signal detection of the P/U ..............................................................................................................................................46
DESCRIPTION OF CIRCUIT.............................................................................................................................................47~53
1. ALPC Circuit ....................................................................................................................................................................47
2. Focus Circuit....................................................................................................................................................................49
3. Tracking & Sled Circuit ....................................................................................................................................................50
4. Spindle Circuit .................................................................................................................................................................53
MAJOR IC INTERNAL BLOCK DIAGRAM AND PIN DESCRIPTION.............................................................................55~72
TROUBLESHOOTING GUIDE ..........................................................................................................................................73~90
BLOCK DIAGRAM ..................................................................................................................................................................91
PRINTED CIRCUIT BOARD DIAGRAM ...........................................................................................................................92~96
ELECTRICAL REPLACEMENT PARTS LIST ........................................................................................................................97
INTRODUCTION
This service manual provides a variety of service
information.
It contains the mechanical structure of the Super
Multi DVD Drive and the electronic circuits in
schematic form. This Super Multi DVD Drive was
manufactured and assembled under our strict quality
control standards and meets or exceeds industry
specifications and standards.
This Super Multi DVD drive is an internal drive unit
designed for use with IBM PC, HP Vectra, or
compatible computer. It can write as much as 700
Mbytes of digital data into CD-R/RW disc, and can
read as much as 700 Mbytes of digital data stored in
a CD-ROM/R/RW disc.
Light Scribe
CD-R
CD-RW
DVD-R
DVD-RW
DVD-R DL
DVD+R
DVD+RW
DVD+R DL
DVD-RAM
GSA
x
48x write
32x write
16x write
4x or 6x write
4x write
16x write
8x write
4x or 6x write
5x write
GMA
x
48x write
32x write
16x write
4x or 6x write
4x write
read only
read only
read only
5x write
G*A-4165B
GWA
x
48x write
32x write
16x write
4x or 6x write
4x write
16x write
8x write
4x or 6x write
read only
GRA
x
48x write
32x write
read only
read only
read only
16x write
8x write
4x or 6x write
read only
Light Scribe
CD-R
CD-RW
DVD-R
DVD-RW
DVD-R DL
DVD+R
DVD+RW
DVD+R DL
DVD-RAM
GSA
x
48x write
32x write
16x write
6x write
4x write
16x write
8x write
6x write
5x write
GMA
x
48x write
32x write
16x write
6x write
4x write
read only
read only
read only
5x write
G*A-4167B
GWA
x
48x write
32x write
16x write
6x write
4x write
16x write
8x write
6x write
read only
GRA
x
48x write
32x write
read only
read only
read only
16x write
8x write
6x write
read only
GCA
x
48x write
32x write
16x write
6x write
4x write
read only
read only
read only
read only
GDA
x
read only
read only
16x write
6x write
4x write
read only
read only
read only
5x write
Light Scribe
CD-R
CD-RW
DVD-R
DVD-RW
DVD-R DL
DVD+R
DVD+RW
DVD+R DL
DVD-RAM
GSA
O
48x write
32x write
16x write
6x write
4x write
16x write
8x write
6x write
5x write
GMA
O
48x write
32x write
16x write
6x write
4x write
read only
read only
read only
5x write
G*A-4168B
GWA
O
48x write
32x write
16x write
6x write
4x write
16x write
8x write
6x write
read only
GRA
O
48x write
32x write
read only
read only
read only
16x write
8x write
6x write
read only
GCA
O
48x write
32x write
16x write
6x write
4x write
read only
read only
read only
read only
GDA
O
read only
read only
16x write
6x write
4x write
read only
read only
read only
5x write
GCA
GDA
x
x
48x write
read only
32x write
read only
16x write
16x write
4x or 6x write 4x or 6x write
4x write
4x write
read only
read only
read only
read only
read only
read only
read only
5x write
FEATURES
1 General
1) Enhanced IDE (ATAPI) interface.
2) Internal Half-height Drive.
3) CD-R/RW, DVD-R/-R DL(Dual Layer)/-RW/RAM/+R/+R DL(Double Layer)/+RW read and write
compatible CD Family and DVD-ROM read compatible.
4) Buffer Under-run prevention function embedded.
5) 2MB buffer memory.
6) Power loading and power eject of a disc. Bare media loading.
7) MTBF : 100,000 POH
8) Vertical and Horizontal installable.
4. Performance
1) Average access time:
(1/3 stroke)
2) Write speed:
DVD-ROM
CD-ROM
DVD-R
DVD-R DL
DVD-RW
DVD-RAM
DVD+R
DVD+R DL
DVD+RW
CD-R
CD-RW
3) Read speed:
DVD-R/RW/ROM/ROM-Dual layer
DVD-R DL
DVD-RAM (Ver.1.0/2.2)
DVD-Video(CSS Compliant Disc)
DVD+R/+RW
DVD+R DL
CD-R/RW/ROM
CD-DA (DAE)
80mm CD
4) Sustained Transfer rate:
DVD-ROM
CD-ROM
5) Burst Transfer rate:
145 ms
125 ms
2x, 4x CLV, 8x ZCLV, 16x PCAV
2x, 4x CLV
1x, 2x, 4x, 6x CLV
2x, 3x ZCLV (Ver.2.2), 3x-5x PCAV(Ver.2.2)
2.4x, 4x CLV, 8x ZCLV, 12x, 16x PCAV
2.4x, 4x, 6x CLV
2.4x, 4x CLV, 8x ZCLV
4x, 8x, 16x CLV, 24x, 32x, 40x, 48x ZCLV
4x, 10x, 16x CLV, 24x, 32x ZCLV
(High Speed: 10x, Ultra Speed: 16x, 24x, 32x)
10x / 8x / 16x / 12x max.
8x max.
2x / 2x, 3x ZCLV, 3x-5x PCAV
8x max. (Single/Dual layer)
10x / 8x max.
8x max.
48x/40x/48x max.
40x max.
16x max.
22.16 Mbytes/s (16x) max.
7,200 kB/s (48x) max.
Ultra DMA Mode2
Multi word DMA Mode2, PIO Mode 4
5. Audio
1) 16 bit digital data output through ATA interface
2) Software Volume Control
3) Equipped with audio line output for audio CD playback
*Definition
Transfer Rate: .........1x (DVD) = 1.385 Mbytes/s ..........1x (CD) = 150 kB/s
Mbytes/s = 106 bytes/s, ................kB/s = 210 bytes/s
Capacity: .................MB = 220 bytes, .............................kB = 210 bytes
SPECIFICATIONS
1. SYSTEM REQUIREMENTS
-CPU: IBM Compatible Pentium 4 2.4GHz (or faster)
(For High speed, 2.4GHz or faster recommended.)
-128MB Memory or greater
* Recording tool
(1) Nero(Ahead)
(2) In CD(Ahead)
(3) Power Producer Gold (Cyber Link)
3. DRIVE PERFORMANCE
3.1 Host interface ..................................................................X3T13 ATA/ATAPI5/1321D
INF-8090i Rev.5.3
3.2 Read/Write & Rotational speed
<Write>
DVD-R ...............................................................2x, 4x(CLV), 8x(ZCLV), 16x(PCAV)
DVD-R DL .........................................................2x, 4x(CLV)
DVD-RW............................................................1x, 2x, 4x, 6x(CLV)
DVD-RAM ...............................Ver. 2.2 .............2x, 3x(ZCLV), 3x-5x(PCAV)
DVD+R ..............................................................2.4x, 4x(CLV), 8x, 12x, 16x(PCAV)
DVD+R DL ........................................................2.4x, 4x, 6x(CLV)
DVD+RW...........................................................2.4x, 4x(CLV), 8x(ZCLV)
CD-R .................................................................4x, 8x, 16x(CLV), 24x, 32x, 40x, 48x(ZCLV)
CD-RW ..............................................................4x, 10x,16x(CLV), 24x, 32x (ZCLV)
(High Speed: 10x, Ultra Speed: 16x, 24x, 32x)
<Read>
5. POWER REQUIREMENTS
5.1 Source voltage
+5V + 5% tolerance, less than 100 mVp-p Ripple voltage
+12V + 10% tolerance, less than 100 mVp-p Ripple voltage
5.2 Current
Idle (Hold track state)..............+5V DC .................0.9A typ. .........< 1.0 A max.
+12V DC ...............0.5A typ...........< 1.0 A max.
Write (Active) ..........................+5V DC .................1.3A typ. .........< 1.5 A max.
+12V DC................0.9A typ. .........< 1.5 A max.
Read (Active) ..........................+5V DC .................1.0A typ. .........< 1.5 A max.
+12V DC................0.9A typ. .........< 1.5 A max.
Seek (Acess) ..........................+5V DC .................1.0A typ. .........< 1.5 A max.
+12V DC ...............1.2A typ. .........< 2.0 A max.
5.3 Standby
Sleep mode (No disc) .............1.1 W typ.
1.3 W max.
6. AUDIO PERFORMANCE
Output Level (1kHz, 0dB) ........................................................0.7 Vrms typical
Frequency Response ..............................................................+/-3dB (20 to 20,000Hz)
Signal to Noise Ratio...............................................................80 dB min. with IHF A and LPF 20 kHz
THD (1kHz, 0dB) .....................................................................0.10% max. with LPF 20 kHz
Channel separation(10kHz).....................................................65 dB min.
Condition: ................................................................................Load inpedance : 10 kohms
7. Acoustic noise
Less than 50dB, A scale, at 0.5 m away from the drive
Note : 1. Disc : Less than imbalance 0.3 x 10-4 Nm
2. Installation : Horizontal
3. Ambient temperature : Normal temperature
4. Except loading, unloading and seek
8. Dimensions
External dimensions (W x H xD)
Front bezel (WxHxD)
Which is not provided with Circuit Diagram of this model. Please Contact the friendly staff of LG
Service Care at: Website http: //www.LGEservice.com
Disc Tray
Stop/Eject Button
1. Disc tray
This is the tray for the disc. Place the disc on the
ejected disc tray, then lightly push the tray (or
push the eject button) and the CD will be loaded.
NOTE: Dont pull out or push in the disc tray
forcibly. This might cause damage to the loading
section of the drive.
2. Stop/Eject button
This button is pressed to open the CD tray.
This button works only when power is supplied to
the drive.
10
Rear Panel
IDE Interface Connector
Jumper Connector
Power Connector
1. Power Connector
Connects to the power supply (5-and 12-V DC) of
the host computer.
NOTE : Be careful to connect with the proper
polarity. Connecting the wrong way may damage
the system (and is not guaranteed). Usually this
connector can only be attached one-way.
2. IDE Interface Connector
Connect to the IDE (Integrated Device
Electronics) Interface using a 40-pin flat IDE
cable.
NOTE : Do not connect or disconnect the cable
when the power is on, as this could cause a short
circuit and damage the system. Always turn the
power OFF when connecting or disconnecting the
cable.
11
3. Jumper Connector
This jumper determines whether the drive is
configured as a master or slave. Changing the
master-slave configuration takes effect after
power-on reset.
4. Analog Audio Output Connector
Provides output to a sound card (analog signal).
Generally you need this to play a regular audio
CD.
5. Digital Audio Output Connector
This connector is not supported.
DISASSEMBLY
1. CABINET and CIRCUIT BOARD
DISASSEMBLY
1-1. Bottom Chassis
A. Release 4 screws (A) and remove the Bottom Chassis
in the direction of arrow (1). (See Fig.1-1)
Cabinet
(1)
(4)
(a)
(A)
Bottom Chassis
(5)
(A)
(A)
(A)
Fig. 1-1
Main
Circuit Board
(b)
Fig. 1-3
Tray Door
(B)
(B)
(3)
Stoppers
Pick-up Unit
(6)
CD Tray
(2)
Fig. 2-1
12
2-2. Pick-up
A. Release 1 screw (C) and remove the Pick-up.
Pick-up Unit
(C)
Pick-up
Fig. 2-2
13
004
035
005
012
EXPLODED VIEW
008
006
009
015
010
011
4
016
A03
A01
013
453
3
034
033
031
001
027
026
007
024
025
445
A02
430
020
028
452
430
028
020
481
482
003
030
021
002
482
032
453
014
482
452
050
482
452
036
021
(LightScribe only)
D
14
E
15
GLOSSARY
ATIP
Absolute Time in Pre-groove. With an additional modulation of the Wobble, the Groove contains a time
code information.
Wobble
CW
DOW
Direct Over-Write. The action in which new information is recored over previously recorded information in
CD-RW disc.
Overwrite
The action in which new information is recorded over previously recorded information.
(Pre-)Groove The guidance track in which clocking and time code information is stored by means of an FM
modulated wobble.
Land
Hybrid Disc A Multisession disc of which the first Session is mastered. On a hybrid disc, recorded and
mastered information may co-exist.
Mastered
Information,stored as pits on the disc during the manufacturing process of the disc.
Information (when making the master)
OPC
Optimum Power Control. Procedure is determined optimum recording power according to CDR/RW Media in recording start step.
ROPC
Running OPC. The purpose is to continuously adjust the writing power to the optimum power
that is required.
When the optimum power may change because of changed conditions of disc and change in
operating temperature.
Jitter
The 16 value of the time variation between leading and trailing edges of a specific (I3 I11) pit
or land as measured by Time Interval Analysis.
Deviation
The difference between a fixed value of Pit length and Land length.
TOC
Table Of Contents : in the Lead-in Area the subcode Q-channel contains information about the
Tracks on the disc.
Packet
Writing
Write
Strategy
The shape of the HF write signal used to modulate the power of the laser.
The Write Strategy must be used for recordings necessary for disc measurements.
Information Wobble, ATIP, Disc Identification, Write Power, Speed Range OPC Parameters, etc are
Area
recorded in the Information area of CD-RW Disc
Finalization The action in which (partially) unrecorded or logically erased tracks are finished and the Lead-in
and/or Lead-out areas are recorded or overwritten with the appropriate TOC subcode.
Logical Erase A method to remove information from a disc area by overwriting it with an EFM signal containing
mode 0 subcode
A logically erased area is equivalent to an unrecorded
Physical Erase The action in which previously recorded information is erased by overwriting with a CW laser
output.
After a Physical Erase action, the erased area on the CD-RW disc is in the unrecorded state
again.
Session
An area on the disc consisting of a Lead-in area, a Program area, a lead-out area.
Multi session A session that contains or can contain more than one session composed Lead-in and Lead-out
19
Track pitch(p)
Read-only
Disc DISC)
CD-ROM
(READ-ONLY
a=30nm
Iw
um
1.6
O
a
T
11
3~
Radial Direction
0.4~0.5 um
Land
Groove
a
Average center
(Pit)Groove
Land
Actual center
2. Disc Specification
ITEM
CD-ROM
CD-R
CD-RW
Standard
Yellow Book
Orange Book II
Record
Not available
Write once
Re-Writeable
> 0.6
> 0.6
< 0.5 mW
< 0.7 mW
< 1.0 mW
Jitter
< 35 nsec
< 35 nsec
< 35 nsec
Reflectivity (Rtop)
70 %
65 %
15 % ~ 25 %
14-65 mW
6-45 mW
Remark)
20
3. Disc Materials
1) CD-ROM disc
Label Printing
Protective Layer
Reflective Layer
Substrate
(Polycarbonate)
Pit
Laser Beam
2) CD-R disc
It is so-called WORM (Write Once Read Many) CD.
It is composed of polycarbonate layer, Organic dye layer, Reflective layer, and Protective
layer.Gold/Silver Reflective layer is used to enhance the reflectivity
According to the kinds of Organic dye layer, it is divided by Green CD, Gold CD, Blue CD.
Laser Wavelength : 780 nm, Laser Power (read) : 0.7 mW
Recording Power : 8x(14~20mW), 16x(25~35mW)
When some part of dye layer is exposed to laser heat, its color changs black.Therefore, writing and
reading is enabled by the difference of reflectivity between changed part and unchanged part.
Polycarbonate layer has Pre_Groove which make a Track.
Pigment
Reflective Layer
Color
Phtalocyanine
Gold/Silver
Yellow/White
Cyanine
Gold/Silver
Azo
Gold/Silver
Dark Blue
Label Printing
Protective Layer
Reflective Layer
Organic Dye Layer
Substrate
(Polycarbonate)
Laser Beam
21
Groove
3) CD-RW Disc
Label Printing
Protective Layer
Dielectric Layer(TL)
Recording Layer
Dielectric Layer(UL)
Substrate
(Polycarbonate)
Groove
Laser Beam
It is composed of polycarbonate layer, alloy(silver, arsenic) layer, aluminum reflectivity layer, protective layer.
An crystalized alloy layer is transformed into noncrystalized by the laser heat. Therefore, writing and reading
is enabled by the difference of reflectivity.
It is possible to overwrite about 1000 times.
Laser Wavelength : 780 nm, Laser Power (Read) : 1.0mW
Recording Power : Erase (4~18mW), Write (6~45mW)
When disc rewriting, new data is overwritten previously recorded data.
Polycarbonate layer has a Pre-Groove which make a track.
H
D
Beam
Spot
Numerical aperture: NA=nsin,
n: Refractive index
Focus depth : H = /NA
laser spot diameter : D = /NA2
Focusing
Lens
Laser Spot
at Constant
Read Intensity
Groove
Land
Mirror
Reflected
Light
Signal
I11
I3
IG
IL
I0
22
(Write)
(Read)
(Read)
a b cd e f
Laser Spot
Position
(Time)
a
b
Laser
Spot
d
e
f
Recorded
Mark
g
Time
Reflected
Light
Signal
a b cd e f
Laser Spot
Position
(Time)
Amorphous
Crystal phase
Melting/
quenching
Erase Power
Read Power
Heating/
gradual cooling
Erased state
(higher reflectivity)
Write Power
Recorded state
(lower reflectivity)
Groove
Crystal
23
Amorphous
Diameter 120 mm
Diameter 46 mm
Diameter 15 mm
Information Area
Lead-in Area
Lead-out Area
Diameter 120 mm
Diameter 45 mm
Diameter 15 mm
Information Area
Unrecorded Disc
PCA PMA
Program Area
Lead-in Area
Lead-out Area
Count Area
in
Tsl-00:35:65 Tsl-00:15:05 Tsl-00:13:25
Tsl
99:59:74
00:00:00
24
HF Signal
A1
0
A2
Time
25
P << Po
Time
P = Po
Time
P >> Po
Level B
11T
OPC
CD-R/RW Media
Program Area
Write Strategy
Determination
PMA Area
Lead-In Area
Lead-out Area
ROPC
26
4
0.7
um
3T
0.4 um
DVD-R/RW Disc
LPP
(Land Pre-Pit)
DVD+R/RW Disc
27
2. Disc Specification
DVD-ROM
DVD-R
DVD-RW
DVD+R
DVD+RW
Read Only
Dye
Phase change
Dye
Phase change
4.7GB
8.54GB
4.7GB
4.7GB
4.7GB
4.7GB
Wavelength
650nm
650nm
650nm
650nm
650nm
650nm
Reflectivity
45~85%
18~30nm
45~85%
18~30%
45~85%
18~30nm
Single-Layer
Dual-Layer
Media Type
Read Only
Track pitch
Minimum pit length
0.74
0.74
0.74
0.74
0.74
0.74
0.4
0.44
0.4
0.4
0.4
0.4
Modulation
>0.6
>0.6
>0.6
>0.6
>0.6
>0.6
26.16MHz
26.16MHz
26.16MHz
26.16MHz
26.16MHz
26.16MHz
Wobble Frequency
140KHz
140KHz
817.4KHz
817.4KHz
Addressing
26.16MHz
26.16MHz
JItter
<8%
<8%
<8%
<8%
0.7 + 0.1
0.7 + 0.1
<9%
<9%
3. Disc Materials
1) DVD-ROM
<Single Layer >
Label
Polycarbonate
Bonding layer
Reflective layer
Polycarbonate
28
DVD+R
Adhesive layer
Protective layer
Reflective layer
Recording layer(dye)
Adhesive layer
Protective layer
Reflective layer
Recording layer(dye)
Disc substrate
Disc substrate
[Playback]
Signals are read with the differences of the reflection of a laser from pits.
Adhesive layer
Protective layer
Reflective layer
Dye layer
Substrate
Laser beam
29
DVD+RW
Adhesive layer
Protective layer
Reflective layer
Dielectric layer
Recording layer
(Phase change material)
Dielectric layer
Disc substrate
Adhesive layer
Protective layer
Reflective layer
Dielectric layer
Recording layer
(Phase change material)
Dielectric layer
Disc substrate
Substrate
Laser beam
Amorphous status
Crystalline status
Recording data
(Melting/Quick cooling)
Erasing data
(Heating/Gradual cooling)
Recorded state
(Low reflection coefficient)
30
T=3
NRZI
2Tw
Channel bits
Ttop
dTtop
Pp
dTle
Pb
T>4
NRZI
2Tw
Channel bits
Ttop
dTtop
Pp
Tw
Tmp
Tmp
Tlp
dTle
Pb
N > 4 : the top pulse (T top ), multi-pulse (Tmp ) and last pulse (Tlp ),
first pulse lead-time dT top, dT le
Pp : Actual write power
Pb : Bias Power
31
NRZI
Channel bits
Tw
2Tw
dTtop
T lp
Tmp
Ttop
dPp
1.25Tw
dTle
Pp
Pc
Pb
0mW
dTtop,3
dPp3
1.25Tw
3T mark
dTle
Ttop,3
dTtop,4
dPp4
1.25Tw
Ttop,4
Etc.
Pb
Pc
4T mark
5T mark
Pb
Tlp
1.25Tw
Ttop,4
Tmp
Tlp
1.25Tw
Ttop,4
Tmp
Tmp Tlp
32
NRZI
Channel bits
Ttop
dTtop
Pp
Pe
Pb
0mW
33
Tw
2Tw
Tmp
Tmp
Tmp
dTera
6. Organization of the Inner Drive Area, Outer Drive Area, Lead-in Zone and
Lead-out Zone
1) Layout of DVD-ROM disc
Disc Center
Diameter 120 mm
Diameter 44 mm
Diameter 33 mm
Diameter 22 mm
Diameter 16 mm
Diameter 15 mm
Clamping
Zone
Center
hole
3rd transtion
area
Information Zone
Rim area
Data Zone
Lead-out Zone
Diameter 120 mm
Diameter 44 mm
Diameter 33 mm
Diameter 22 mm
Diameter 16 mm
Diameter 15 mm
Clamping
Zone
Center
hole
3rd transtion
area
Information Zone
Rim area
Unrecorded Disc
Inner Drive
Area
Inner Disc
Test Zone
Lead-in
Zone
Inner Disc
Count Zone
Data Zone
Outer Drive
Area
Lead -out
Zone
Outer Disc
Test Zone
Outer Disc
Count Zone
in
PSN: 23080H 27080H 27480H 28480H 2A480H 30000H 260540H 261940H 262940H
OUT
263940H
267940H
34
Diameter 120 mm
Diameter 44 mm
Diameter 33 mm
Diameter 22 mm
Diameter 16 mm
Diameter 15 mm
Clamping
Zone
Center
hole
3rd transtion
area
Information Zone
Rim area
Unrecorded Disc
Inner Disc
Test Zone
Data Zone
Lead-in Zone
Inner Disc
Count Zone
Outer Disc
Test Zone
Outer Disc
Count Zone
in
PSN: 2A480H
OUT
2A7C80H
2DC80H
30000H
260540H
262940H
265940H
35
266140H
LightScribe Media
1. LightScribe Media
DiscOD
Label Zone
Control Feature Zone
Clamping/Logo Zone
Center Hole
36
37
Buffer
Memory
Host
PC
uP
(DSP)
Power
Drive
Optical FG
SERVO Signals
CIrcuit
RFOUT
Analog
Signal
Processor
RF Cell Signals
Focus Actuator
(Focus)
Laser Power Reference
Tilt Actuator
(Tilt)
Track Actuator
Step Motor
(Sled)
(Track)
Spindle Motor
(Spindle)
Optical
Encoder
Optical
Pick-up
MECHANISM
38
Codewheel
Direction of
radial play
Encoder PCB
Optical Encoder IC
PIN 6
VCC
PIN 1
CH B
PIN 5
CH A
PIN 4
GND
PIN 2
GND
PIN 6
VCC
PIN 1
CH B
PIN 5
CH A
PIN 2
GND
PIN 4
GND
PIN 3
VLED
PIN 3
VLED
GND
GND
Vcc
VCC
CH A
FFC
3PIN
OFG
CH B
CH B
39
SIGNAL
PROCESSING
CIRCUITRY
CODEWHEEL
OR
CODESTRIP
P-up
Unit
(HOP-7632TS)
IC302
Flash ROM
FE GEN
TE/CSO GEN
RF EQ & AGC
IC101
RF AMP
(R2S35002)
DVD
CD
SRAM
RF data slice
Data PLL
Servo ADC
Focus/tracking
control output
Sled control output
CAV Spindle control
SERVO
DSP
IC301
(R8J32007)
U-COM
DRAM
EFM demodulator
CiRC error correction
Audio DAC
Buffer/Memory controller
CSS controller
Atapi interface control
Data
Status
Command
40
HOST DVD
PLAYER
(EMPEG2 B/D)
R8J32007
Scrambled MPEG Data
Brief Process
1. Regional Code for DVD Disc
DVD-ROM drive transfers the regional code of the control data to host by the command of host, the DVD
player of host reads the regional code, and plays title in the case of allowed regional code only.
2. Management of DVD Disc for the scrambled of data
(1) DVD-ROM and DVD player of host generate the KEY 1 respectively, transfer to opposite part, the
KEY 2 is received, recognizes the data transfer or not with this value, and generates the bus key
encoded the data.
(2) Encoded Disc Key and Title Key host is transfer with the bus Key.
(3) DVD player of host reads the key value, and uses the value to restore the scrambled data.
* Refer to the next page for the details.
41
AGID
HOST
ROM-DRIVE
Challenge key
MPEG-2
BOARD
1. Drive and host gives and takes the ID of 2bit. This ID is AGID (Authentication Grant ID).
The various decoder boards are attached to the host, in these, AGID sets the MPEG-2 board and drive.
2. After the AGID is set, MPEG-2 board generates the challenge key (10 Byte) and transfers to drive. The
board and drive generate key 1 (5Byte) with the challenge key respectively. (Of course, the Algorithm
generating the key 1 is not known.)
3. Compare with the generated key 1, if it corresponds each other, the first step of authentication is
completed. This is a course to identify the MPEG-2 board with a drive.
4. The second step of authentication is a course to identify a drive with the MPEG-2 board.
The dirve generates a challenge key and transfers it to the MPEG-2 board. The dirve and MPEG-2 board
generate the key 2 (5Byte) with the challenge key, compare with each other, and if it corresponds and the
secondary step of authentication is completed.
5. As above, the identification is completed.
6. The dirve and MPEG-2 board generate the Bus key with the key 1 and key 2 and own it.
7. Dirve encodes the disc key and title key with this Bus key and transfers to the MPEG-2 board.
8. The MPEG-2 board reads the encoded disc key and title key with the Bus key only.
9. MPEG-2 board lets data read from the drive to decode with the read disc key and title key and makes into
the video signal by decoding.
42
1
GRL
RUS
FIN
CAN
FST
LTU
BIR
POI
UKR
MNG
U.S.A
TUR
TKM
CHN
JRN
BHS
CUB
FGY
KOR
BMG
MIX
AFG
PAK
MMR
PRI. VIR
JPN
2
HKG TWN
MAC
PHL
MNP
GUM
MDI
PLW
PNG
5
2
AUS
ZAF
ISO
SWZ
NZL
DISC
Example)
The disc
manufactured
in the U.S.A,
has the
number one.
43
ROM - DRIVE
Transfer to
MPEG-2 board
reading the
regional code.
MPEG-2 BOARD
VGA CARD
MONITOR
Receiving
data from the
MPEG-2
board and
output
through the
monitor
45 Tilt44 Tilt+
IC2(FM)
43 TR-
CD-VR
42 TR+
R14
41 AF40 AF+
Rd
38 FM
C12
DVD-VR
39 GND(FM)
37 VREF
36 SEL
C13
35 VCC(FM)
34 ENA
R2
C3
33 IAPC
32 SLG
31 VSA5
R1
R4
30 VSL25
16 15 14 13 12 11 10
SLG
Rfreq
IAPC
17 VSO
ISLOP
AGND
EN
RSET
DVD-LD
19 OUT2
20 VSO
GND 5
GND 4
NRZB 3
NRZ 2
RWB 1
21 VSO
22 GND
NC
NC
BUSY
SEN
28 CLKB
27 GND(LDD)
C2
C1
FB1
26 NRZB
25 NRZ
R7
24 GND(LDD)
R8
23 MONITOR
22 RWB
21 SDIO
SDIO
SCLK
MON1
23 OUT1
29 CLK
FB2
VSA 9
VSL 8
CLK 7
CLKB 6
18 OUT2
CD-LD 24 OUT1
25 VSO
IC2(LDD)
20 SCLK
19 BUSY
26 27 28 29 30 31 32
18 SEN
17 VSO
C6
C5 FB3
16 Vcc(FM)
C9
15 GND(OEIC,TEMP)
C10
Rth
IC3(OEIC)
C14
7 GND
F4
F1
6 VD
F3
F2
EF4 8
4 VS
3 VC2
VA 10
13 RF+
12 E2+F2
EF1 9
5 VCC
C15
14 RF-
11 C
10 A
9 E1+F1
VB 11
8 E4+F4
VEF2 12
7 D
6 B
5 E3+F3
2 VEF3
E4
E1
VREP 13
1 SW
E3
E2
VRFN
14
4 GAINSW
3 Vc(OEIC)
2 Vcc(OEIC)
1 GND(OEIC,TEMP)
Behind View
44
45
No.
Signal Name
I/O
Signal Description
GND(OEIC,TEMP)
Vcc(OEIC)
Vc(OEIC)
GAINSW
OEIC output gain control (High:Low gain, Middle:Middle gain, Low:High gain)
E3+F3
E4+F4
E1+F1
10
11
12
E2+F2
13
RF+
14
RF-
15
GND(OEIC.TEMP)
16
TEMP
17
VSO
18
SEN
19
BUSY
20
SCLK
21
SDIO
I/O
22
RWB
23
MONITOR
Monitor output
24
GND(LDD)
25
NRZ
26
NRZB
27
GND(LDD)
28
CLKB
29
CLK
30
VSL25
31
VSA5
32
SLG
33
IAPC
34
ENA
35
VCC(FM)
36
SEL
Low: selects
DVDFMOUT
High: selects
CDFMOUT
37
VREF
38
FM
39
GND(FM)
40
AF+
41
AF-
42
TR+
43
TR-
44
Tilt+
45
Tilt-
Infrared Iaser
Pick-Up module
Focusing
Tracking
Photo Diode
Track Center
Tp/2
Sub1
F,E
D,C
A,B
Main
Sub2
H,G
Tp
k[(F+H) - (E+G)]
Offset
(A+D) - (B+C)
TE
46
DESCRIPTION OF CIRCUIT
1. ALPC (Automatic Laser Power Control) Circuit
1-1. Block Diagram
CN101
Optical
Pick-up
LD
Driver
Write
Strategy
FsDAC
WDAC
25,26,28
13
9
8
IAPC
2.5VREF
R160
FMON
12
9
10
buffer
LPF
&
Gain
S/H
IC101 (R2S35002))
+
-
APCDAC
(REDA/WRDA)
MUX
RWAPC
AMP
Buffer
S/H
B/H
28
29
32
RFPDSH
WFPDSH
WGATE
TCPH
BCNT
R106
R105
126
127
134
175
108
120,121,123
IC301 (R8J32007)
C106
C105
47
48
2. Focus Circuit
2-1. Block Diagram
A+B+C+D
LPF
HAVC
LS
to
0.8V
HAVC
LS
to
V14
A,B,C,D
IC101
R2S35002
A,B,C,D
LPF
(EF1~EF4)
Disc
Motor unit
(A+C)-(B+D)
(A+C)-(B+D)+K[(EF1+EF3)-(EF2+EF4)]
Optical
Pick-up
HOP-7632TS
FOD
180
IC301
R8J32007
FACT- FACT+
FACT+
FACT-
DAC
Focusing
Compensator
35
FE
FE
R102
C405
R103
FE
ADC
169
GND
PE
42
R2S30202FP
GND
R329
FOD
40
IC601
C406
170
FOIN
34
PE
C335
REF
1.65V
EN1
20
CTL1
EN2
21
CTL2
49
IC101
R2S35002
MPPO
(A+D)-(B+C)
L
P
F
SPPO
A,B,C,D
(EF1~EF4)
Disc
Motor unit
HAVC
LS
to
V14
L
P
F
TE
1
TE
R101
Optical
Pick-up
HOP-7632TS
(A+D)-(B+C)-K[(EF1+EF4)-(EF2+EF3)]
C101
TRD
Tracking
Compensator
DAC
181
ADC
GND
173
TE
TACT- TACT+
SL2
183
Sled
Compensator
DAC
182
A+
IC301
R8J32007
SL1
AB+
B-
SLED MOTOR
Unit
(CN601)
TACT+
37
TACT-
39
BA+
SL2N
EN1
20
8
SL1N
TRD
IC601
R2S30202FP
A-
CTL1
R372
1.65V
1.65V
CTL2
21
10
SL2P
R331
SL1IN
6
SL1P
C336
EN2
SL2
2
SL2IN
B+
R330
TOIN
36
C337
R373
R332
SL1
C338
42
R374
REF
1.65V
C604
50
IC101
R2S35002
MPPO
(A+D)-(B+C)
A,B,C,D
Disc
Motor unit
SPPO
(EF1~EF4)
[(EF1+EF4)-(EF2+EF3)]
Optical
Pick-up
HOP-7632TS
L
P
F
HAVC
LS
to
V14
L
P
F
TE1
38
MIRR
VREF1
A+B+C+D
L
P
F
TACT- TACT+
L
P
F
A+
VREF1
HAVC
LS
to
V14
MIRR
DET
AB+
SUMF
79
EQ
RFIP
80
AGC
B-
SLED MOTOR
Unit
BOTTOM
HOLD
TOP
HOLD
RFIN 81
63
62
MIRRTOPH
GND
MIRRBOTH
C128
C127
GND
GND
C101
TE
IC301
R8J32007
173
R101
Track Counter
and Timer
TE1
IP2MIRR
MIRR
149
M
U
X
A
D
C
Short
Seek
Algorithm
Tracking
Compensator
D
A
C
Loog
Seek
Algorithm
Sled
Compensator
D
A
C
TRD
181
SL2
183
182
SL1
51
52
4. Spindle Circuit
4-1-1. Block Diagram(FGCAV Servo)
Optical
Pick-up
HOP-7632TS
Disc
Motor unit
IC301
R8J32007
X301
33.8688MHz
XCO
VCK4M
106
Control Clock
Generator
107
XCI
SFG
SPD
SPD
211
R349
P
W
M
M
U
X
CAV FD
+
CAV PD
213
VCK4M
R361
R375
Motor Kick
REG
C349
3.3V
1.65V
SPIN
U
12
13
IC601
SPD
1
DAVC
42
1.65
R2S30202FP
W
14
CTL1 20
CTL1
CTL2 21
CTL2
19
SFG
FG
53
C117
WAG1
C118
WAG2
WAG3
18 19
SA
87
ADO
SB
Disc
Motor unit
SD
Optical
Pick-up
HOP-7632TS
HPF
S
/
H
88
SC
20
89
AGC1
HPF
HPF
AGC2
BCO
90
MA
92
C171 MB
BPF
HPF
AGC3
93
C172
MC
C173
94
HPF
WOBSIG
+
37
MD
VREF
95
C174
GND
IC101
R2S35002
WBLSH
31
WBLS H
IC301
R8J32007
1.65V
154
R375
SPD
SPD
211
R349
C349
1.65V
P
W
M
M
U
X
SP
Motor Kick
REG
PH
54
VDD1(3.3V)
EQON
EQOP
GND1
TOPH
BOTH
MIRRTOPH
MIRRBOTH
MIRRHPF
BHC
VDD4(3.3V)
MRSTB
SDEN
70
69
68
67
66
65
64
63
62
61
60
59
58
57
PORT10
SUBI/LPPSIG
71
PORT11
SUBO/LPPMON
72
PORT12
EQFCF
73
PORT13
IREFE
74
SDATA
AGHPF2
75
SCLK
AGHPF1
Pin Assignment
56
55
54
53
52
51
AGFU
76
50
MCLK
AGFR
77
49
PORT07
(5V)VCC1
78
48
PORT06
SUMF/SUMF2
79
47
PORT05
RFIP
80
46
PORT04
45
PORT03
44
PORT02
RFIN
SRVREF
81
82
FVREFO
83
43
PORT01
IREFT
84
42
PORT00
VREF1
85
41
GND4
HAVC
86
SA
87
SB
88
SC
89
SD
R2S35002
(TOP VIEW)
DFT
39
IP1/LPPOUT
38
IP2/MIRR
98
28
RFPDSH
AIN3
99
27
SPBLVL/TISH2
100
26
LNDTRK
TE
GND5
AIN2
AWOBSIG
WFPDSH
(3.3V)VDD5
MPDSH/SPDSH
29
(EQOS/RRF/WRF/LPPMON/)ATEST
30
97
WOBFCF
96
AIN1
WAG3
GND2
WAG2
WBLSH
WAG1
31
GND3
WGATE
95
VRDC
32
MD
VRDCN
94
VRDC2N/PWRMON
MC
LDOUT
RFHLD/TISH1
VRDC3N
33
FMD
IDGATE
93
(3.3V)VDD3
34
MB
FVREF
LO_ZB/SPDSH
(5V)VCC2
35
92
BHBETA/TIE
91
MA
PHBETA/TCE
(3.3V)VDD2
LE
BLANK
BCENT
36
FE
WOBSIG
90
PE
37
SIGM
55
40
Block Diagram
3300p 0.1u
RF SLIM/SUB
(RGA)
SUMF2
to WRF
AGHPF1
IREFE
AGHPF2
AGFR
AGFU
RFHLD/
TISH1
RF
AGC
HP2
mclk
to MIRR.DEFECT
EQOP
RF
EQ
HP3
EQON
EQAUTO
EQOS
M
U
X
IP1/LPPOUT
IP2/MIRR
VREF1
4700p
SUBP.N
RFIN
LO_ZB/
SPDSH
RFIP
0.068u
IDGATE
SUMF/
SUMF2
0.068u
12k
(*2)
0.47u
*3300P/0.068u
EQFCF
*3300p
Lo-Z function by IDGATE.
.
. 3.3us
fast mode
Lo-Z function by IDGATE.
M
U
X
MIRR
SUBO/LPPMON
ATEST
LPPMON/EQOS/RRF/WRF
SUBI/LPPSIG
mclk
ID
DET
M
U
X
BHC
15,000p
LPP
SUBW
mclk
2200p
VREF1
MA
MB
MC
Pick
I/F
WOBFCF
F0-CNT
Wobble
0.47u
S/H
WOB
AWOBSIG
AGC1
MD
BPF
COMP
AGC3
*HPF fc=1kHz
AGC2
WAG3
BPO
WAG1
S/H
main
SA
to A/D
0.1u
WOBSIG
SUB
VREF1
WAG2
0.1U
SB
0.12U
SC
0.12U
LNDTRK
SD
TE
sub
BALANCE
TE
S/H
to LPF,A/D
DPD
to LE
MPP SPP
FE
FE
BALANCE
toLPF,A/D
HAVC
pick-up I/F
reference level
PE
PE
toLPF,A/D
MPP
SHPE
WBLSH
HFSUM
RRF
SPP
HFPE
FE
MPDSH/
SPDSH
MUX
LE
LO_ZB/SPDSH
pin
toLPF,A/D
SUMF2
M
WRF
WRF U
X
mclk
MCLK
D/A
SRVREF
20k(*1)
IREFT
BLANK
D
MIRRTOPH
MIRRBOTH
VREF1(=2.1V)
FVREFO(=2.5V)
VFREFO
0.01u
D
D
D
D
SDEN
SCLK
SDATA
TOPH
MIRR
DFT
0.068u
RFHLD/TISH1 pin
12
PORT00~07.10~13
SPBLVL/TISH2
TIE
D
D
0.033u
BOTH
Programm
able I/O
port
Power
Cont.
Serial
Cont.
Reg.
0.033u
0.1u
IP2/MIRR pin
MRSTB
0.033u
MIRRHPF
MIRR
DEFECT
EQOP/N
WGATE
SPBLVL
APC
GCAOUT
PWWMON
BHOUT
FVREF
GND2
VDD1
0.1u
vCC1
GND3
VDD2
0.1u
vCC2
GND4
VDD3
0.1u
VDD5
VRDC
PHBETA/TCE
BHBETA/TIE
BCENT
toLPF,A/D
toLPF,A/D
toLPF,A/D
RFHLD/TISH1 pin
each blocks
LDOUT
VRDCN
VRDC3N
FMD
R-OPC
OPC
BPO
GND1
RFPDSH
GND5
VDD4
LO_ZB/SPDSH
WGATE
0.1u
VRDC2N/
PWRMON
SIGM
AIN1~3
SIGM
toLPF,A/D
0.1u
0.1u
8200p
3.3u
power 3.3V(VDD)
0.1u
...Combined pin
In the case of
analog APC
680k
0.01u
RECD
VHALH(=VDD/2)
VREF
VREF1
10u
RECD
SAV
0.1u
power 3.3V
D ...digital pin
D/A...digital/analog pin
power 5V
56
Pin Functions
pin Name
max. voltage
Function
TE
Analog-Output
FE
Analog-Output
PE
Analog-Output
PE output terminal
LE
Analog-Output
BCENT
Analog-Output
PHBETA/TCE
Analog-Output
BHBETA/TIE
Analog-Output
VCC2
Power
FVREF
Analog-Input
VDD
FMD
10
Analog-Input
VDD
VDD3
11
Power
LDOUT
12
Analog-Output
VRDC3N
13
External-components required
VRDC2N/PWRMON
14
External-components required
VRDCN
15
External-components required
VRDC
16
External-components required
GND3
17
Ground
WAG1
18
External-capacitor required
WAG2
19
External-capacitor required
WAG3
20
External-capacitor required
WOBFCF
21
External-capacitor required
VDD5
22
Power
ATEST
23
Analog-Output
AWOBSIG
24
Analog-Output
GND5
25
Ground
LNDTRK
26
Digital-Inputpull-up
VDD
SPBLVL/TISH2
27
Digital-Inputpull-up
VDD
RFPDSH
28
Digital-Input
VDD
WFPDSH
29
Digital-Input
putpull-up
VDD
MPDSH/SPDSH
30
Digital-Input
putpull-up
VDD
WBLSH
31
Digital-Input
putpull-up
VDD
WGATE
32
Digital-Input
putpull-up
VDD
RFHLD/TISH1
33
Digital-Input
putpull-up
VDD
IDGATE
34
Digital-Input
putpull-up
VDD
LO_ZB/SPDSH
35
Digital-Input
putpull-up
VDD
57
pin Name
BLANK
max. voltage
Function
Digital-Output
WOBSIG
37
Digital-Output
IP2/MIRR
38
Digital-Output
IP1/LPPOUT
39
Digital-Output
DFT
40
Digital-Output
GND4
41
Ground
PORT00
42
Digital-Input/Output
PORT01
43
PORT02
44
PORT03
45
PORT04
46
PORT05
47
PORT06
48
PORT07
49
MCLK
50
I/O Port
VDD
Digital/Analog-Input
No pull-up
PORT10
51
Digital-Input/Output
PORT11
52
PORT12
53
PORT13
54
SCLK
55
VDD
I/O Port
VDD
No pull-up
Digital-Input
pull-up
SDATA
56
Digital-Input/Output
pull-up
VDD
SDEN
57
Digital-Input
pull-up
VDD
MRSTB
58
Digital-Input
pull-up
VDD
VDD4
59
Power
BHC
60
External-capacitor required
MIRRHPF
61
External-capacitor required
MIRRBOTH
62
External-capacitor required
MIRRTOPH
63
External-capacitor required
BOTH
64
External-capacitor required
TOPH
65
External-capacitor required
GND1
66
Ground
EQOP
67
Differential-Output
EQON
68
VDD1
69
Power
SUBI/LPPSIG
70
Analog-Input
VDD
58
pin Name
max. voltage
Function
SUBO/LPPMON
71
Analog-Output
EQFCF
72
External-capacitor required
IREFE
73
External-resistor required
AGHPF2
74
External-capacitor required
output terminal
external capacitor
Terminal to connect RF-equalizer fc setting external
resistor
AGHPF1
75
AGFU
76
External-capacitor required
AGFR
77
External-capacitor required
VCC1
78
Power
SUMF/SUMF2
79
RFIP
80
RFIN
81
Differential-Input
VDD
SRVREF
FVREFO
82
Analog-Input
VDD
83
Analog-Output
IREFT
84
External-resistor required
VREF1
85
Analog-Output
HAVC
86
Analog-Input
VCC
SA
87
Analog-Input
VCC
SB
88
Analog-Input
SC
89
Analog-Input
SD
90
Analog-Input
VCC
VDD2
91
Power
MA
92
Analog-Input
MB
93
Analog-Input
MC
94
Analog-Input
MD
95
Analog-Input
GND2
96
Ground
AIN1
97
Analog-Input
AIN2
98
Analog-Input
AIN3
99
Analog-Input
SIGM
100
Analog-Output
59
216
215
214
213
212
211
210
209
208
207
206
205
204
203
202
201
200
199
198
197
196
195
194
193
192
191
190
189
188
187
186
185
184
183
182
181
180
179
178
177
176
175
174
173
172
171
170
169
168
167
166
165
164
163
CPU15
A17
EF G
SFG
TLD
SPD
LDD
LE D
GPIO04
ICUIN8
ICUIN6
ICUIN7
TE STB1
TE STB2
MRSTB
VSSIO
VCCIO
VCC
PTE ST3
VDDAA
PTE ST2
VSSA
REXT
VDDAA
PTE ST1
VSSA
VINP
VDDAA
VINN
VSSA
VCCA
VCCA
DAVC
TV DN
TV DP
TRD
FOD
GAD1
GAD0
BCENT
TIB H
TCPH
LPSA
TE
AT ZC
SIGM
PE
FE
VSSA
VSSA
VCCA
W1LPF0
W1LPF1
W1LPF2
R8J32007
Top View
162
161
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
W2LPF0
W2LPF1
W2LPF2
VDD AA
VSSAA
DE FECT
BL AN K
LN DTRK
WOBSIG
L OWZB
ID GATE
RFH L D
IP1LP PIN
IP2M IRR
VCCI O
VSSIO
VDD
VSS
VSSA
NRZI
NRZIB
DCL K B
DCL K
VCCA
WRGATEB
SRFH
SRFL
WRSTOP
WRGATE2
VCCI O
VSSIO
VSS
VDD
WBL SH
MPDS H
WFPDSH
RFPDSH
TCSHSPBLV
LDB USY
WDEN
RFDEN
SDAT A
SCL K
FE MCK
TRST
TDO
TDI
TCK
TMS
TE ST3
TE ST2
TE ST1
TE ST0
DOUT
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
A2
GPIO05
VSSIO
VCCIO
HR STB
DATA7
DATA8
DATA6
DATA9
DATA5
DAT A10
DATA4
DAT A11
DATA3
DAT A12
DATA2
DAT A13
VDD
VSS
VSSIO
VCCIO
DATA1
DAT A14
DATA0
DAT A15
DREQ
ZIOWB
ZIORB
IORDY
DACKB
HIN TRQ
IOCS16B
VSSIO
VCCIO
DA1
PDIA GB
DA0
DA2
CS1FXB
CS3FXB
DASPB
GPIO07
GPIO06
ROUT
VCCA
LOU T
ADIP VR1
ADIP VRT
ADIPINP
VSSA
VSSA
XCO
XCI
VCCA
VSSR
VCCR
CPU14
CPU13
CPU12
VSSIO
VCCIO
VCCRQ
CPU11
CPU10
VSSRQ
CPU9
CPU8
CPRDB
UCS0B
A1
CPU0
CPU1
CPU2
CPU3
CPU4
VSSRQ
CPU5
CPU6
CPU7
VCCRQ
VSS
VDD
A16
A15
VSSIO
VCCIO
A14
A13
A12
A11
A10
A9
A20
CPWRB
VDD
VSS
A19
A18
A8
A7
A6
A5
A4
A3
VSSIO
VCCIO
VCCR
VSSR
60
CAV
AUDIO
VINP
VINN
Data
PLL
ADC
WPLL
DVD
Scramble
LPP
Detector
Wobble
Generator
ADC
CD-DSP
Jitter
Counter
W2LPF[2:0]
ADIPVR1
ADIPVRT
ADIPINP
DVD
PI-ECU
ADIP
Detector
DVD
PO-ECU
IP1LPPIN
IP2MIRR
LOWZB
IDGATE
RFHLD
NRZI,NRZIB
DCLK,DCLKB
WGATEB
WRGATE2
SRFH
SRFL
WRSTOP
WBLSH
MPDSH
WFPDSH
RFPDSH
TCSHSPBLV
ATAPI
DREQ
DACKB
DASPB
CS3FXB
CS1FXB
PDIAGB
DA2
DA1
DA0
IOCS16B
HINTRQ
IORDY
ZIORB
ZIOWB
HRSTB
DATA [15:0]
PRML
W1LPF[2:0]
WOBSIG
LOUT
ROUT
DOUT
DVD
Descramble
CD-ROM
Decoder
REXT
PTEST [2:0]
AUDIO
DRAM
Interface
Demodulate
LVDS
Modulator
SDRAM
16Mbit
XCI
XCO
Clock
Generator
FEMCK
CD
CD-ROM
Encoder
MRSTB
Test
Control
TESTB[1:2]
TEST[3:0]
Sample
SCLK
SDATA
RFDEN
WDEN
LDBUSY
DRAM
Hold
Serial I/F
TLD
LDD
LED
SPD
LNDTRK
SFG
EFG
DERECT
ATZC
BLANK
FE
PE
SIGM
ZCS
RD[15:0]
RA[12.10:0]
RAMCL
DWE
DRAS
DCAS
DQMU
DQML
DCKE
CPWRB
CPRDB
A[20:0]
MCIF
Cmp
UCS0B
GPIO05(UCS1B)
CPRDB
CPWRB
A[20:1]
GPIO04(A[0])
CPU[15:0]
CPU[15:0]
UCS2B
UCS3B
ADC
Servo
MSEQ
GPIO06(CSEL)
TE
LPSA
WAIT
ADGATEB
INT0B
INT1B
INT2B
FOK
INT3B
ADC
GPIO07(HEATRUN)
H8S
ICUIN6(EJECTSW)
ICUIN7(ACTFLG)
CPU
ICUIN8(LOADIN)
SSEQ
FOD
DAVC
TRD
TVDP
TVDN
TCPH
TIBH
BCENT
FAD0(VRDC2N)
GAD1
61
TRST(NMI)
DAC
BCA
DAC
Auth
ADC
TCK(SCK)
TDI(SCI)
TDO(SCO)
TMS
Pin Name
VSSR
VCCR
CPU14
CPU13
CPU12
VSSIO
VCCIO
VCCRQ
CPU11
CPU10
VSSRQ
CPU9
CPU8
CPRDB
USC0B
A1
CPU0
CPU1
CPU2
CPU3
CPU4
VSSRQ
CPU5
CPU6
CPU7
VCCRQ
VSS
VDD
A16
A15
VSSIO
VCCIO
A14
A13
A12
A11
A10
A9
A20
CPWRB
VDD
VSS
A19
A18
A8
A7
A6
A5
A4
A3
VSSIO
VCCIO
VCCR
VSSR
Pin no
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
Pin Name
A2
GPIO05
VSSIO
VCCIO
HRSTB
DATA7
DATA8
DATA6
DATA9
DATA5
DATA10
DATA4
DATA11
DATA3
DATA12
DATA2
DATA13
VDD
VSS
VSSIO
VCCIO
DATA1
DATA14
DATA0
DATA15
DREQ
ZIOWB
ZIORB
IORDY
DACKB
HINTRQ
IOCS16B
VSSIO
VCCIO
DA1
PDIAGB
DA0
DA2
CS1FXB
CS3FXB
DASPB
CPIO07
CPIO06
ROUT
VCCA
LOUT
ADIPVR1
ADIPVRT
ADIPINP
VSSA
VSSA
XCO
XCI
VCCA
Pin no
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
Pin Name
DOUT
TEST0
TEST1
TEST2
TEST3
TMS
TCK
TDI
TDO
TRST
FEMCK
SCLK
SDATA
RFDEN
WDEN
LDBUSY
TCSHSPBLV
RFPDSH
WFPDSH
MPDSH
WBLSH
VDD
VSS
VSSIO
VCCIO
WRGATE2
WRSTOP
SRFL
SRFH
WRGATEB
VCCA
DCLK
DCLKB
NRZIB
NRZI
VSSA
VSS
VDD
VSSIO
VCCIO
IP2MIRR
IP1LPPIN
RFHLD
IDGATE
LOWZB
WOBSIG
LNDTRK
BLANK
DEFECT
VSSAA
VDDAA
W2LPF2
W2LPF1
W2LPF0
Pin no
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
Pin Name
W1LPF2
W1LPF1
W1LPF0
VCCA
VSSA
VSSA
FE
PE
SIGM
ATZC
TE
LPSA
TCPH
TIBH
BCENT
GAD0
GAD1
FOD
TRD
TVDP
TVDN
DAVC
VCCA
VCCA
VSSA
VINN
VDDAA
VINP
VSSA
PTEST1
VDDAA
REXT
VSSA
PTEST2
VDDAA
PTEST3
VCC
VCCIO
VSSIO
MRSTB
TESTB2
TESTB1
ICUIN7
ICUIN6
ICUIN8
GPIO04
LED
LDD
SPD
TLD
SFG
EFG
A17
CPU15
62
Analog Input
Analog Output
Analog Input/Output
Standard Input
Standard Input with Pull Up
Standard Output
Standard Three State Output
Standard Input/Output
IOU :
5I :
5O :
5TO :
5IO :
PW :
GND :
I/O
destination
Function
VINP
VINN
190
188
AI
AFE
REXT
194
AO
External Resistance
PTEST1
PTEST2
PTEST3
192
196
198
AO
External Resistance
63
162
161
160
I/O
destination
Function
AO External Components Write PLL1 filter connect pin (0)
Write PLL1 filter connect pin (1)
Write PLL1 filter connect pin (2)
AO External Components Write PLL2 filter connect pin (0)
Write PLL2 filter connect pin (1)
Write PLL2 filter connect pin (2)
Pin No.
BLANK
156
AFE
DEFECT
157
AFE
SFG
213
IU
DRVR
EFG
214
PU
Spindle FG pulse
(also input to the H8S interrupt port INT4)
Spindle FG pulse for Light Scribe
(also input to the H8S interrupt port INT4)
TLD
212
TO
DRVR
SPD
211
TO
DRVR
LDD
210
TO
DRVR
LED
209
TO
PU
ATZC
172
AI
AFE
FE
169
AI
AFE
PE
170
AI
AFE
SIGM
171
AI
AFE
TE
173
AI
AFE
LPSA
174
AI
AFE
TCPH
175
AI
AFE
TIBH
176
AI
AFE
BCENT
177
AI
AFE
GAD1
179
AI
GAD0(VRDC2N)
178
AI
FOD
180
AO
DRVR
TRD
181
AO
DRVR
TVDP
TVDN
182
183
AO
DRVR
DAVC
184
AO
DRVR
64
Pin No.
I/O
HRSTB
DA2
DA1
DA0
59
92
89
91
5I
5I
ATAPI
ATAPI
DATA[15:0]
79,77,71,
69,67,65,
63,61,60,
62,64,66,
68,70,76,
78
5IO
ATAPI
DREQ
80
5TO
ATAPI
ZIOWB
81
5I
ATAPI
ZIORB
82
5I
ATAPI
IORDY
83
5TO
ATAPI
DACKB
84
5I
ATAPI
HINTRQ
85
5TO
ATAPI
IOCS16B
86
5TO
ATAPI
PDIAGB
90
5IO
ATAPI
CS1FXB
CS3FXB
93
94
5I
ATAPI
DASPB
95
5IO
ATAPI
65
destination Function
destination
Function
IP1LPPIN
150
AFE
IP2MIRR
149
AFE
WOBSIG
LOWZB
154
153
I
O
AFE
AFE
IDGATE
152
AFE
RFHLD
151
AFE
WRGATE2
134
AFE
WBLSH
129
AFE
MPDSH
128
AFE
WFPDSH
127
AFE
RFPDSH
126
AFE
TCSHSPBLV
125
AFE
WRGATEB
138
PU
SRFH
137
PU
SRFL
136
WRSTOP
135
PU
LNDTRK
155
AFE/PU
NRZI
143
AO
PU
NRZIB
142
DCLK
140
DCLKB
141
ADIPVR1
101
AO External Cpmponents
ADIPVRT
102
AO External Cpmponents
ADIPINP
103
AI
PU
AFE
I/O
destination
Function
LDBUSY
124
IO
LDD
LDD serial IF busy also functions as the CPU general port 1-0
WDEN
123
LDD
RFDEN
122
AFE
SDATA
121
IO
AFE/LDD
SCLK
120
AFE/LDD
66
I/O
destination
Function
DOUT
109
IO
ATAPI
ROUT
98
AO
ATAPI
LOUT
100
I/O
destination
Function
FEMCK
119
AFE
XCO
106
Xtal
XCI
107
Xtal
ICUIN6(EJECTSW)
206
ICUIN8(LOADIN)
207
IO
GPIO07(HEATRUN)
96
5IO
ATAPI
GPIO06(CSEL)
97
5IO
ATAPI
GPIO04(A0)
208
IO
SRAM
GPIO05(UCS1B)
56
IO
SRAM
Load Switch CPU general port1-1 also connected to the CPU interrupt
port INT8: Loader in sensor
Pin No.
15
I/O
O
destination
Flash
Function
H8S / CS0
CPWRB
40
Flash / SRAM
H8S / WRB
CPRDB
14
Flash / SRAM
H8S / RDB
A[20:1]
39,43,44,
215,29,30,
33,34,35,
36,37,38,
45,46,47,
48,49,50,
55,16
Flash / SRAM
H8S / A[20:1]
CPU[15:1]
216,3,4,
5,9,10,
IO
Flash / SRAM
H8S / D[15:0]
CPU[0] can also function as the CPU general port 0-4
(multiplexed).
12,13,25,
24,23,21,
20,19,18
17
67
Pin No.
202
I/O
I
destination
RESET IC
Function
Master reset input
TESTB2
TESTB1
203
204
TMS
114
IU
E10emulator
TCK
115
IOU
E10emulator
TDI
116
IU
E10emulator
TDO
117
E10emulator
TRST
118
E10emulator
TEST0
TEST1
TEST2
TEST3
110
111
112
113
IO
Test select
T*SEL[3:0]
TEST0
TEST1
TEST2
TEST3
Servo monitor 0
Servo monitor 1
Servo monitor 2
Servo monitor 3
WPLL monitor 0
WPLL monitor 1
WPLL monitor 2
WPLL monitor 3
Audio 0
Audio 1
Audio 2
Audio 3
DVD modulation 0
DVD modulation 1
DVD modulation 2
DVD modulation 0
DVD-R/CD-R
monitor 0
DVD-R/CD-R
monitor1
DVD-R/CD-R
monitor 2
DVD-R/CD-R
monitor 3
DVD+RW monitor 0
DVD+RW monitor1
DVD+RW monitor 2
DVD+RW monitor 3
PI/C1
PI/C1
PI/C1
PI/C1
PO/C2
PO/C2
PO/C2
PO/C2
DEMO 0
DEMO 1
DEMO 2
DEMO 3
10
CLVCK
CLVCK
CLVCK
CLVCK
11
BLEND
BLEND
BLEND
BLEND
12
PRML monitor 0
PRML monitor 1
PRML monitor 2
PRML monitor 3
13
14
RAMCON monitor 0
RAMCON monitor 1
RAMCOM monitor 2
RAMCON monitor 3
15
MIF monitor 0
MIF monitor 1
MIF monitor 2
MIF monitor 3
16
WOBREF monitor 0
WOBREF monitor 1
WOBREF monitor 2
WOBREF monitor 3
T*SEL can be set for each of pins TEST3, TEST2, TEST1, and TEST0, respectively.
68
Pin No.
28,41,72,
I/O
PW
Function
DSP core power supply (1.5V)
PW
130,146
VCCR
2,53
VCCRQ
8,26
VDDAA
159
189,193,197
VCCA
99
PW
108
139
166
185
186
VCC
199
PW
VCCIO
7,32,52,
PW
58,75,88,
133,148,200
VSS
27,42,73,
GND
131,145
VSSR
1,54
GND
SDRAM GND
VSSRQ
11,22
GND
VSSA
104
GND
105
144
Analog GND:LVDS
167
Analog GND:WPLL1,2
168
187,191,195
VSSAA
158
GND
VSSIO
6,31,51,
GND
57,74,87,
132,147,201
69
VM1
22
STTH
SPGS
23
24
ACTRST
25
LO+
27
VM3
LO28
26
TO-
GND
FO+
34
29
FO35
30
TL+
36
TO+
TL37
31
TLIN
38
GND
TOIN
39
5VCC
FOIN
40
32
LOIN
41
33
REF
42
Pin Layout
18
19
20
21
FG
EN1
EN2
16
COMMON
SLLIM
15
ACTFLG
17
14
TEST
13
9
SL1+
8
SL2-
7
GND
12
6
SL2+
5
VM2
11
4
SPLIM
10
3
SL2IN
SL1-
GND
1
SPIN
SL1IN
R2S3
0202FP
Pin Function
No Pin name
1
SPIN
2
SL1IN
3
SL2IN
4
SPLIM
5
VM2
6
SL2+
7
GND
8
SL29
SL1+
10
SL111
GND
12
U
13
V
14
W
15 ACTFLG
16 COMMON
17
TEST
18
SLLIM
19
FG
20
EN1
21
EN2
Function
Spindle control voltage input
Slide control voltage input1
Slide control voltage input2
Input terminal for spindle current limit
Motor Power Supply 2(for Slide)
Slide non-inverted output2
GND
Slide inverted output2
Slide non-inverted output1
Slide inverted outptut1
GND
Motor drive output U
Motor drive output V
Motor drive output W
Pickup protect flag output
Motor common
Test terminal (*1)
Input terminal for slide current limit
Frequency generator output
Input terminal for enable 1
Input terminal for enable 2
No Pin name
42
REF
41
LOIN
40
FOIN
39
TOIN
38
TLIN
37
TL36
TL+
35
FO34
FO+
33
GND
32
5VCC
31
TO+
30
TO29
GND
28
LO27
LO+
26
VM3
25 ACTRST
24
STTH
23 SPGS
22
VM1
Function
Reference voltage input
Loading control input
Focus control voltage input
Tracking control voltage input
Tilt control voltage input
Tilt inverted output
Tilt non-inverted output
Focus inverted output
Focus non-inverted output
GND
5V Power Supply (for FS,TS,TL)
Tracking non-inverted output
Tracking inverted output
GND
Loading inverted outptut
Loading non-inverted output
Power Supply3(for Loading)
Pickup protect Reset (*2)
Reference voltage for spindle start up
Input terminal for gain select SPM
Motor Power Supply 1(for Spindle)
70
7-13.2V
STTH
OUTPUT Ron
1ohm
U
CLK
STARTER
SPLIM
TSD
Frequenc y
150KHz
PWM
CIRCUIT
FG(x3)
Reverse detect
6.4MHz
commutation
Commutation
p
cho
nt
urre
C
SWICHING
SIN
M
PW
p er
For SLIDE
SPIN
COMMON
VM1
CTL
DSP
GND
Current
sense
FG
BACK EMF
DETECTER
Current gain
3A/V
0.6A/V
DSP
For SPINDLE
SPM
V/V converter
REF
DSP
FOIN
DSP
VM2
7-13.2V
A MP
FO-
4.5-5.5V
GND
re
Cu r
nt
ch
PWM
CIRCUIT
er
opp
Current gain
0.88 A/V
CTL
Frequenc y
75KHz
B TL
SL2IN
DSP
M
PW
A MP
TR-
DSP
re
Cu r
nt
ch
er
opp
Frequenc y
75KHz
PWM
CIRCUIT
CTL
Current gain
0.88 A/V
B TL
TLIN
A MP
M
PW
B TL
7-13.2V
4.5-5.5V
LO+ -
H Bridge
ENABLE
Gain Select
(SPM)
TEST mode
VM3
For /FO/TR/TILT
ACTRST
OUTPUT Ron
1.5ohm
FO+
DSP
5VCC
SL2-
SLIDE1
V/V converter
Current
sense
TRIN
SL1IN
TLDSP
OUTPUT Ron
1.5ohm
TR+
Current
sense
GND
+
SL1+
SL2+
OUTPUT Ron
1.8 ohm
DSP
DSP
OUTPUT Ron
1.5ohm
TL+
SLLIM
SLIDE2
V/V converter
DSP
STM
SL1OUTPUT Ron
1.8 ohm
Pickup Protect
ACTFLG
LO+
For LOADING
OUTPUT Ron
1.5ohm
TEST
GND
EN 1
EN 2
SPGS
DSP
DSP
Block Diagram
71
FOIN, TOIN,TLIN
TEST
5VCC
5VCC
REF
EN1, EN2
5VCC
5VCC
100
100
100
100
17k
35k
SPGS
ACTFLG,FG
ACTRST
(Temperature monitor)
COMMON
5VCC
VM1
5VCC
5VCC
5VCC
5VCC
10k
100
100
COMMON
25k
VM1, U, V, W
VM1
SL1+
SL1-
SL2+
5VCC
FO+
72
FO-
TO+
TO-
SL2-
VM3
TL+
TL-
LO+
LO-
100
TROUBLESHOOTING GUIDE
(01) Laser Power Adjust (using RD Power/WR Power/Erase Power)
MPU & DSP
IC301
Pickup
Setting
FFC
Pin#175
AFE
IC101
#12
Front
Monitor
LD
Driver
FFC
#6 #10
IC102
pin#98
LD
Driver
FFC
Pin#79
Pin#110
AFE
IC101
C137
Pin#203
Pin#21
Setting
FE:R102,C405
Pickup
FFC
#2
AFE
IC101
TE:R101,C101
#1
PE:R103,C406
#3
DVD-Dual Disc
Setting
AFE
IC101
FE:R102,C405
Pin#
87-90
Pickup
FFC
#2
Focus:#34-35
R329,C335 #40
Driver
IC601
Slider FPC
Slider, #6,8-10
73
AFE
IC101
FE:R102,C405
All Disc
Pin#
87-90
Pickup
FFC
#2
PE:R103,C406
#3
Focus:#34-35
R329,
C335
Driver
IC601
#40
AFE
IC101
TE:R101,C101
Pin#
87-90
Pickup
FFC
#1
Tracking
#30-31
Driver
IC601
#39
Slider FPC
Slider:#6,8-10
All Disc
#2
TE:R101,C101
R329,C335
R330,C336
74
AFE
IC101
#1
Pin#
87-90
FFC
Pickup
Focus:#34-35
Tracking:#30-31
#40
#39
Driver
IC601
Slider FPC
Slider:#6,8-10
AFE
IC101
Pin#
80-81
FFC Pickup
SIGM:R148, C151
#100
#171
Slider FPC
Slider:#6, 8-10
Driver
IC601
Pin#
87-90,80-81
AFE
IC101
Setting
FFC Pickup
FE:R102,C405
#2
Slider FPC
Slider:#6, 8-10
Driver
IC601
AFE
IC101
Setting
SIGM:R148,C151
Pin#
87-90,80-81
FFC Pickup
#100
Driver
IC601
Slider FPC
Slider:#6, 8-10
Setting
AFE
IC101
C341,343
DVD-RAM Disc
Pin#
87-90,80-81
FFC Pickup
#67,68
Driver
IC601
Slider FPC
Slider:#6, 8-10
75
DVD-RAM Disc
Pin#
Setting
TCE:R106, C106
FFC
#6
TIE:R107,C107
#7
Driver
IC601
Slider FPC
Slider:#6, 8-10
TE:R101, C101
AFE
IC101
DVD-R/RW Disc
Pin#
87-90, 80-81
FFC
#1
Pickup
TILT: #36-37
#181
TRD:R330,C336
Driver
IC601
#39
Tracking: #30-31
Slider FPC
Slider:#6,8-10
Setting
AFE
IC101
FE:R102, C405
DVD-R/RW Disc
FFC
#2
FE:#34-35
FE
R329, C335
#40 Driver
IC601
TE:R101, C101
AFE
IC101
DVD-R/RW Disc
Pin#
87-90,80-81
FFC
Pickup
#1
#181
TRD:
R330, C336
76
Tracking:#30-31
Driver
#39
IC601
Slider FPC
Slider:#6, 8-10
Pickup
#178
(Temp.Information)
FFC
putemp
Pin#
12-14
#1
Driver
IC601
SPD:R349, C349
#213
FG
Spindle
FFC
#19
AFE
IC101
DVD+R Disc
Pin#
87-90,80-81
FFC
Pickup
#37
Driver
IC601
Slider FPC
Slider:#6, 8-10
DVD-R/RW Disc
AFE
IC101
C341, 343
#67,68
Pin#
87-90,80-81
FFC
Pickup
#39
Driver
IC601
Slider FPC
Slider:#6,8-10
77
AFE
IC101
Driver
IC601
Slider FPC
Slider:#6,8-10
Slider/
Spindle
#43
Spindle FFC
AFE
IC101
FE:R102,C405
#2
All Disc
Pin#
87-90
FFC
Pickup
TE:R101,C101
#1
Focus:#34-35
Tracking:#30-31
PE:R103,C406
#3
R329,C335
R330, C336
78
FOD
#40
Driver
IC601
TRD
#39
Slider FPC
Slider:#6,8-10
Error Code
SSB Byte8,9
Contents of fail
Fail Analysis
Block Diagram
28xx
(Exchange
low/high byte)
LP Adjust NG.
No.01
Byte8: xxh
Byte9: 28h
48xx
No.02
5Exx
No.02
4C0x to 4C4x
No.03
4C5x to 4C7x
4C80
4CAx
79
Error Code
SSB Byte21,22
Contents of fail
Fail Analysis
Block Diagram
42xx
No.04
452x
No.05
450x
451x
454x
No.06
458x
No.07
47xx
No.08
49xx
Unwritten Slice Level Adjust NG. 4906: RAM Disc NG (Exchange Disc).
(RAM Only)
1) Check solder of IC101circumference.
(pin#1,2,3 pin#87-90)
2) Exchange IC101(AFE).
3) Exchange IC301(MPU & DSP).
N0.09
80
No.
Error Code
Contents of fail
SSB Byte21,22
Fail Analysis
Block Diagram
4Axx
No.10
4A5x
4A6x
No.11
4A8x
No.12
10
4B0x
No.13
11
4B8x
12
4CCx
1) Exchange Pickup.
2) Exchange IC101(AFE).
3) Exchange IC301(MPU & DSP).
No.12
13
4Dxx
No.15
14
182x
01xx
No.21
15
52xx
No.16
No.14
81
No.
Error Code
SSB Byte21,22
Contents of fail
Fail Analysis
Block Diagram
16
54xx
No.07
17
55xx
No.14
18
56xx
No.06
19
57xx
No.13
20
58xx
No.17
21
59xx
No.18
82
No.
Error Code
SSB Byte21,22
Contents of fail
Fail Analysis
Block Diagram
22
5Axx
23
5Cxx
No.06
24
5Dxx
No.20
83
Error Code
SSB Byte21,22
Contents of fail
Fail Analysis
Block Diagram
2503,2504
No.21
2020,2021
Focus Fail.
No.22
2101,2102
Tracking Fail.
No.22
2000~2010
Spindle Fail.
No.18
84
Poly SW
12V
12V
SW701
miniSMDC150F/24
(Raychem)
S705 OPEN
Vso
S704 OPEN
L151
IC101 AFE(R2S35002)
VCC1 #08 Power (5.0V)
VCC2 #78 Power (5.0V)
5VR
CN101 P/U
OEIC(Vcc) #44 & FM(Vcc) #11
Poly SW
5V in
SW702
miniSMDC150F/24
(Raychem)
Tr
Q631
UMC5N
UMC5N
Tr
Q651
5V
Audio Output
Q901 Tr(UMC5N)/Q902 Tr(UMG4N)
S714 OPEN
5VP
L602
Torex Regurator
IC703 XCM403AA03SR
Vin=5.00 V
V0=2.80 V
S708 OPEN
IC703
2.8V
REG
2.5(2.8)
S709 OPEN
IC703
3.3V
REG
L150
3.3A
Pc=
W
Vin=5.00 V
V0=3.30 V
3.3A
S715 OPEN
3.3A-2
R354
0
L710
3.3D
L305
Torex Regurator
IC701 XCM403AA02SR
Vin=2.80 V
V0=1.50 V
S706 OPEN
IC701
1.5V
REG
L301
L304
1.5D
IC701
2.8V
REG
Pc=
W
Vin=5.00 V
V0=2.80 V
85
86
Circuit/IC
Power supply
2
3
(IC701)
4
5
(IC703)
Flash-ROM
(IC302)
8
9
DSP
10
(IC301)
Signal
Signal/Level
Line-12V
12V
CN801-41
Line-5V
5V
CN801-44
reg-1.5V
1.5V
IC701-2
reg-2.8V
2.8V
IC703-5
reg-3.3V
3.3V
IC703-2
VDD : 3.3V
3.3V
37
CS
Active-Low
26
XRD
read-CK
28
VDD : 1.5V
1.5V
VCC(D) : 3.3V
3.3V
7, 32, 52, 58, 75, 88, 133, 148, 200, 199, 2, 53, 185,
11
VCC(A) : 3.3V
3.3V
186, 166, 99
12
Clock-34MHz
33.8688MHz
106, 107
13
MRSTB
(3.3V)High
202
139, 108, 8, 26
14
AFE
VCC : 5.0V
5.0V
8, 78
15
(IC101)
VDD : 3.3V
3.3V
16
OP-amp
VCC : 5.0V
5.0V
5VCC : 5V
5V
32
VM3 : 5V
5V
26
19
VM1, 2 : 12V
12V
5, 22
20
REF : 1.65V
1.65V
42
(IC102)
17
7ch-DRV
18
(IC601)
21
VCC(FM) : 5.0V
5.0V
11
22
Pick-up
VCC(OEIC) : 5.0V
5.0V
44
23
VC(OEIC) : 2.1V
2.1V
43
24
VREF : 2.5V
2.5V
25
VSL25 : 2.8V
2.8V
16
26
VSA5 : 5.0V
5.0V
15
27
VSO : 5.0V
5.0V
29
* When there are twe or more power supply pins of LSI, it checks by one ramdom pin first.
87
88
2. LED does not blink at all at the time of a power supply injection. Eject-SW does not react.
(1) Is it normal to the exterior Bus (Data-Bus, Address-Bus, control signal system) of MPU?
Viewing check: -- a short circuit, opening, etc.
The device connected to the exterior Bus of MPU in DSP, and its signal list
Peripheral device
Flash -ROM
[Bus/Signal]
(IC302)
Address
A1~A20
Data
D0~D15
CS*
CS0B
WCK
WR
RCK
RD
89
SPDL-MT
STEP-MT
Load-MT
Focus-ACT
Track-ACT
Tilt-ACT
Input
(1)SPIN
(2)SL1IN
(3)SL2IN
(41)LOIN
(40)FOIN
(39)TOIN
(38)TLIN
(34)FO+
(35)FO-
(31)TO+
(30)TO-
(36)TL+
(37)TL-
Reference
Output
(42)REF 1.65V
(12)U
(13)V
(14)W
(6)SL2+
(8)SL2(9)SL1+
(10)SL1-
(27)LO+
(28)LO-
90
EN2(21)
Low
High
Low
High
SPDL
off
off
on
on
SLED
off
on
on
on
Load
off
on
off
off
Focus/Track/Tilt
off
off
on
on
BLOCK DIAGRAM
Flash-ROM
(2MByte)
MBM29LV160BE
or Equivalent
(FUJITSU)
OPU:HOP-7632TS
(HITACHI ME)
Disc
Interface
connector
Loading
motor
PU
Disc
motor
Unit
mechanism
Slide
motor
100pin-TQTF
(RENESAS)
DVD/CD DSP
(DVD/CD/Servo/ATAPI)
R8J32007FP
256pin LQFP
(RENESAS)
DVD-codec
CD-codec
LPP/ADIP decorder
Servo DSP
ATAPI-IF
Microprocessor
7ch-Driver
R2S30202FP
SPDL/SLED/Fo/Tr/Ti/LD
(RENESAS)
Analog
audio
Host IDE
Tray Detect
SW
Device
configuration
jumper
MASTER
SLAVE
CSEL
Eject
SW
Limit
SW
LED
3.3V
2.8V
3.3V/2.8V Reg.IC
XCM403AA03SR
(TOREX)
RST
1.5V
12V
GND
5V
2.8V/1.5V Reg.IC
XCM403AA02SR
(TOREX)
RST
91