DT-350B
CONTENTS
CONTENT---------------------------------------------------------------------1
IMPORTANT SAFETY PRECAUTIONS------------------------------------2
ASSEMBLY INSTRUCTIONS------------------------------------------------3-5
FOLDING
INSTRUCTIONS------------------------------------------------6
UNFOLDING
INCLINE
INSTRUCTIONS------------------------------------------6
INSTRUCTIONS-----------------------------------------------7
GROUNDING
METHODS---------------------------------------------------8
OPERATION
GETTING
GUIDE---------------------------------------------9-16
STARTED
GUIDE---------------------------------------------17
SAFETY EXERCISE--------------------------------------------------------------18
WARM-UP
EXERCISE------------------------------------------------------19
MAINTENANCE INSTRUCTIONS--------------------------------------------20
MOTOR BELT ADJUSTMENT-------------------------------------------------21
BELT
ADJUSTMENT-------------------------------------------------------22
EXPLODED
DRAWING-----------------------------------------------23
LIST------------------------------------------------------------24-25
WARNING
1 Before starting any exercise program, consult with your physician or health professional
specially the person who above 35 years old people or has some health problem before. We take
no responsibility for any troubles and hurts due to above reasons.
ATTENTION:
1When using this treadmill, keep attaching the safety pull pin rope to your clothes or belt.
2Do not plug anything into any parts of this equipment, or it may damage.
3Position the treadmill on a clear, level surface. Do not place the treadmill on thick carpet as it may
interfere with proper ventilation. Also, do not place the treadmill near water or outdoors.
4Never start the treadmill while you are standing on the walking belt. After turning the power on and
adjusting the speed control, there may be a pause before the walking belt begins to move, always
stand on the foot rails on the sides of the frame until the belt is moving.
5Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose fitting clothing
that could become caught in the treadmill. Always wear running or aerobic shoes with rubber soles.
6Keep small children or pet away from the treadmill during operation.
7Do not do exercise in 40 minutes after meal.
8The treadmill is only used for adultschild use the treadmill must have adult on side.
9Always hold the handrails when initially walking or running on the treadmill, until you are
comfortable with the use of the treadmill.
10The treadmill for indoor equipment, do not use outdoor. Position the treadmill on a clean, level
surface. Note the treadmill made by special equipment, please do not remodel or do others.
11The power cord of motorized treadmill is specialized. If the power cord damaged, please
purchase it from distributor or contact our company directly.
12If the treadmill should suddenly increase in speed due to an electronics failure or the speed
being inadvertently increased, the treadmill will come to a sudden stop when the pull pin is
disengaged from the console.
13Do not connection in the middle of power cord, extending the power cord or replace the power
cord plug ,Stacked weight object on the power cord or make the power cord near the high
2
ASSEMBLY INSTRUCTIONS
temperature heat, prohibit use the porous socket, otherwise it will cause fire or electric shock injury
accident because of poor contact.
14When the treadmill is not being used, the power cord should be unplugged and the safety pull
pin removed.
WHEN YOU OPEN THE CARTON, YOU WILL FIND THE BELOW SPARE PARTS.
1
4L/R
23
32L/33R
47
67
70
71
73
84
86
87
94
DES.
MAIN FRAME
4L/R
UPRIGHT
SPECIFICATION
Q'Y
NO
DES.
SPECIFICATION
Q'Y
70
MP3 WIRE
71
BOLT
M10*20
COMPUTER
73
BOLT
M10*80
23
SAFETY KEY
84
SCREW DRIVER
32L/33R
FRONT COVER
86
ALLEN WRENCH
S6
47
POWER LINE
87
ALLEN WRENCH
S5
67
WASHER
12
94
BOLT
M4*15
L/R
L/R
11*20*t2
FIXING TOOLS:
5# ALLEN WRENCH
6# ALLEN WRENCH
1pc
1pc
3
SCREW DRIVER
1pc
Step 1 Open the box and put the MAIN FRAME (1) on the floor. Connect COMPUTER
BOTTOM WIRE (17) and COMPUTER MIDDLE WIRE (44), and lock the UPRIGHT (4L/R) as
arrow direction to the MAIN FRAME (1). Use M10*20 BOLT (71) / M10*80 BOLT (73) and
11*20*t2.0 WASHER (67) to lock the UPRIGHT (4L/R). ( do not lock too tight)
STEP 2 Connect COMPUTER TOP WIRE (44) and COMPUTER MIDDLE WIRE (46).
Use M10*20 BOLT (71) and 11*20*t2.0 WASHER (67) to fix the COMPUTER (9) onto the
UPRIGHT (4L/R). (Lock all the bolts tightlly.)
Step 3Use M4*15 bolt (94) to lock front cover (32L/33R) tightly onto the upright
(4L/R). Put on the SAFETY KEY (23) & MP3 WIRE (70).
FOLDING INSTRUCTION
UNFOLDING INSTRUCTION
ATTENTION
Must confirm complete assembly as the required above and lock all bolts.
Do the following operation after checking everything is OK.
Before you use the treadmill, please read the instruction carefully.
GROUNDING
METHODS
lightly and
INCLINE INSTRUCTIONS
PIC I
PIC II
INCLINE INSTRUCTIONS
INCLINE+INCLINE-and +-on handrail is incline add and subtract button.
To adjust incline when treadmill running, the stepping is 1 level / time.
Press the button more than 2 seconds, will be up or down automatic.
Also have shortcut key 4, 8 , 12.
PIC I shows incline 0, PIC II shows incline 20.
OPERATION GUIDE
This product must be grounded. If it should be malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of electric
shock. This product is equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
DANGER Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with
the product if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This product is for use on a nominal 230V circuit and has a grounding plug that looks
like the plug illustrated in sketch A in following figure. Make that the product is
connected to an outlet having the same configuration as the plug. No adapter should be
used with this product.
1. WINDOWS DISPLAY
Windows display a default value and shine. Click "SPEED + -" button to adjust to the necessary
values. Press START button. After 3 seconds, the treadmill will start with the lowest speed. Click
"SPEED + -", 4 / 8 / 12 or rotate the right handrail around to adjust speed . Press INCLINE
(+-), 4 / 8 / 12 or rotate the left handrail around to adjust incline. When countdown to 0, the
treadmill will stop slowly. Also you could press the "STOP" button or take away the safety lock to
stop.
8. BUILD-IN PROGRAM
When the treadmill is not running, press PROG button, the speed window will display P1-P18.
Choose any one in P1---P18 and the time window shows default value 30:00 and flickers.
Press "SPEED + -" or INCLINE+-button to adjust the time you need. Press "START" button to
start build-in program. Built-in program totally has 16 sections and running time of every section
is set time/16. When enter the next section, it will make a sound of Bi to prompt. The systems
speed is changed as the program. And you can adjust the speed with SPEED +,- when
running. But when enter the next section, it will recover this sections speed. After all sections
finish, the system will make a sound of bi-bi- ten prompt sound and display End. At this
time, press STOP button can make the treadmill restoration, and it will enter standby mode.
Manual mode is the default program, the default speed in kilometer is 1.0 km/h.and the
fastest speed is 22.0 km/h.
PROGRAM EXERCISE CHAT
10
TIME
PROG
P1
P2
P3
P4
P5
10.
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
10
11
12
13
14
15
16
INCLINE
SPEED
10
10
INCLINE
SPEED
12
12
12
INCLINE
SPEED
10
10
12
INCLINE
SPEED
12
12
12
12
INCLINE
SPEED
12
12
12
12
12
12
INCLINE
SPEED
INCLINE
SPEED
12
12
INCLINE
SPEED
10
10
12
INCLINE
10
SPEED
10
10
10
10
INCLINE
SPEED
10
10
10
INCLINE
SPEED
10
10
INCLINE
SPEED
10
12
12
12
INCLINE
SPEED
10
10
10
INCLINE
SPEED
10
10
10
INCLINE
SPEED
12
12
12
12
12
12
INCLINE
SPEED
10
12
10
INCLINE
SPEED
10
10
INCLINE
4 114
SPEED
11
12
10
10
10
10
ARRANGE
NOTE
SEX
01--02
AGE
1099 YEARS
HEIGHT
FABMI 100200 CM
WEIGHT 19
RESULT
UNDER WEIGHT
20150 KGS
20--25
NORMAL WEIGHT
25--29
OVER WEIGHT
30
OBESITY
12
headset socket. When you are playing music,please make sure the treadmill is in louder
state, not MUTE state.
A. SD card / USB disk display:
Insert the SD card or USB disk with music, the system will play them automatically.
Press buttons to choose the music or adjust the volume as you like.
B. MP3 wire display:
Insert the MP3 wire into your audio device (MP3 / PHONE) to display the music.
Press buttons to choose the music or adjust the volume as you like.
C. Headset socket.
Insert headset socket into the hole on the computer to listen to the voice.
D. FM FUNCTION.
Press FM button to start FM function,the system will play FM automatically.
Press buttons to choose the channel or adjust the volume as you like.
FM frequency bands: 87.5 MHZ--108 MHZ
ATTENTION
When youplay FM / SD / USB / MP3 all together, the priority level is as below:
1, MP3 wire
2, FM function.
2,SD card or USB disk.
13. POWER SAVING MODE
This system includes power saving mode, When the treadmill is not running, If there is no button
instruction for 10 minutes. The system will enter power saving mode and close the display. Press
any button can awaken system.
14. SAFETY LOCK FUNCTION
The window shows"SAFETY KEY PROTECTION" when take away the safety lock and the
13
PREPARE
If you are around 35 years old, or have health problem, even this is your first time to do fitness
exercise, please consult doctor or professional before use it. Before do exercise, please stand on the
side to learn how to operate, such as start, stop and speed adjustment. After that stand on the plastic
deck of the treadmill board, catch hold of the handrail, start by 1.6--3.2 km/h low speed, stand straight,
look forward, one foot try to do few times, then stand on the belt to do exercise. After adapting, you can
adjust the speed to 3--5 km/h and keep doing about 10 minutes, then stop.
EXERCISE
Please stand on the side to learn how to operate, such as speed and incline, until you know it then can
14
SAFETY EXERCISE
start do exercise. Walk 1 km by constant step need about 15-25 minutes, please record it in fact. And
walk 1km by 4.8 km/h need about 12 minutes. If you can do it easily by few times, then can adjust the
high speed and incline, and go on to do 30 minutes, you can take a good exercise. Before do slow walk
exerciseplease remember it is for your health and can not irritable
AMOUNT OF EXERCISE
SHORTCUT----The best way to save time is do 15-20 minutes exercise.
Warm up 2 minutes by 4.8 km/h, and adjust the speed to 5.3 km/h and 5.8 km/h, continue do exercise by
this two speeds. Then add 0.3 km/h per 2mins speed increase, until you feel breathing quickened but
not breathe hard. Keep this speed to do exercise, if feels uncomfortable, please reduce 0.3 km/h. Leave
4 minutes to reduce speed at last. If you fell it is hard to strengthen exercises by increase speed, then
you can choose the way of increase incline slowly, it also can strengthen exercise.
CONSUMPTION OF HEAT----This way can really consumption the heat.
Warm up 5 minutes by 4--4.8 km/h speed, then add 0.3 km/h per 2 minutes increasing speed, you can
do 45mins on the speed that you feel it is comfortable and challenge. In order to strengthen do exercise.
You can do 1 hour by this speed and add 0.3 km/h speed when you heard some business
advertisements, and return the speed back when go to next program, so at this period, the heat will be
consumed enough. At last keep 4 minutes to reduce the speed.
EXERCISE FREQUENCY
Target is 3--5 times per week, do 15-60mins each time. It is better to make a time schedule, do not
accord to your favor. You can get the strenuous exercise degree through adjusting speed and incline.
We'd suggest that do not set incline when start do exercise.
Please consult professional staff before do exercise. He can help recommendation exercise
rate/intension and time according to your age and health condition. When running, if you feel chest
tightness or chest pain, irregular Heartbeats, short of breath, dizziness or other unwell, please stop
immediately! And consult professional before you want continually to do exercise. If you often use
treadmill, you can choose normal walk speed or jog speed.
If you have no experience or can't make sure the best testing speed, you can reference below
standard:
Speed 1-3.0 km
Speed 3.0-4.5 km
Speed 4.5-6.0 km
Speed 6.0-7.5 km
Speed 7.5-9.0 km
Speed 9.0-12.0 km
More than 12.0 km
15
WARM-UP EXERCISE
MAINTENANCE INSTRUCTION
ATTENTION
It is suitable for walker to choose less than or equal to 6 km speed.
It is suitable for runner to choose more than or equal to 8.0 km speed.
It is better to do some warm-up exercise. Warm the muscle easy stretch, so use 5-10 minutes to
warm-up. Then stop and according below method to do stretch exercise for five times, and each
foot do 10 seconds or more every time. After running, do those stretch exercises one more time.
4).
5. Sartorius (Inner Muscles of the Thigh)
Muscle Stretches Sitting down with your soles
opposite and knees outward. Pull feet toward groin Keep
10-15 seconds, and relax. Repeat 3 times (See
picture 5).
16
CLEANING
General cleaning or the unit will greatly prolong the treadmill.
Keep treadmill clean by dusting regularly. Be sure to clean the exposed part of the deck on either
side of the walking belt and also the side rails. This reduces the build up of foreign material
underneath the walking belt. Make sure the shoes are clean. The top of the belt may be cleaned
with a wet, soapy cloth. Be careful to keep liquid away from inside the motorized treadmill frame
or from underneath the belt.
WARNING
Always unplug the treadmill from the electrical outlet before removing the motor cover. At least
once a year remove the motor cover and vacuum under the motor cover.
This treadmill's walking belt and deck are equipped with a pre-lubricated, low maintenance deck
system. The belt/ deck friction may play a major role in the function and life of your treadmill,
thus requiring periodic lubrication. We recommend a periodic inspection of the deck.
We recommend lubrication of the deck according to the following timetable
Light user (less than 3 hours/ week)
annually
Medium user (3-5 hours/ week)
every six months
Heavy user (more than 5 hours/ week)
every three months
If you feel the running belt has occasional pause when you are running, the running belt or motor
belt is flabby, you need to adjust it.
JUDGEMENT METHODS
Step 1: Open the motor cover, then let the treadmill work by the slowest speed.
Step 2: Stand on the running belt and move together with it, hang on to the handrail foam and
try your best to press the running belt with your feet.
Step 3: If the running belt doesnt stop when you press it, the running belt and motor belt is not
flabby or not tight. They are just right;
If the running belt stops when you press it, but the front roller doesnt stop, then you need to
adjust the running belt (see the belt adjustment); If the running belt and front roller stop when
press the running belt, the motor belt is flabby, you need to adjust it.
17
BELT ADJUSTMENT
ADJUST METHODS
Step 1: Close the power, and open the motor cover.
Step 2: Unscrew the four bolts of motor and adjust the threaded bar with 6# allen wrench. If
you can use hand to reverse the motor belt by 120or more, then the motor belt is too flabby. It
should be adjusted tightly. If you can reverse the motor belt about 60, then the motor belt is just
right. There is no need to adjust it.
Step 3: Lock the bolt of motor base frame and assemble the motor cover.
PARTS LIST
EXPLODED DRAWING
belt moderate tightness. SEE PIC C.
NO.
DESCRIPTION
REMARK
Q'Y
NO.
DESCRIPTION
MAIN FRAME
26
LOUDSPEAKER COVER L
BASE FRAME
27
LOUDSPEAKER COVER R
INCLINE BRACKET
28
SOUD MESH R
4L/R
UPRIGHT
29
MOTOR BRACKET
30
19
REMARK
Q'Y
FRONT ROLLER
31
REAR ROLLER
32L
FRONT COVER L
COMPUTER BRACKET
33R
FRONT OVER R
COMPUTER TOP
34
DISPLAY DECAL
1
1
COVER
10
SIDE RAILS
35
11
BOTTLE BRACKET
36
CYLINER
12
COMPUTER BOTTOM
37
ADJUSTING WHEELS
F=35 KGS
COVER
13
SOUD MESH L
38
CUSHION PAD
14
MOTOR BOTTOM
39
COVER
15
MOTOR BELT
40
MOVING WHEELS
16
HANDRAIL FOAMS
41
17
COMPUTER BOTTOM
42
20*30*T1.5
WIRE
18
43
19
COMPUTER BOARD
44
COMPUTER MIDDLE
WIRE
20
COMPUTER BOTTOM
45
POWER SWITCH
BOARD
21
RUNNGING BOARD
46
OVERLOAD PROTECTOR
22
RUNNING BELT
47
POWER WIRE
23
SAFETY KEY
48
L TAIL PLUG
24
49
BOLT
50
ST4*15
43
BELT
25L/R
END CAP
20
REMARK
DESCRIPTION
51
SIGLE WIRE
75
CABLE TIES
52
MOTOR
76
BOLT
M8*25
53
INCLINE
MOTOR
77
BOLT
M8*40
54
MOTOR
CUSHION
78
BOLT
M8*35
55
BOLT
79
BOLT
M6*60
56
CONTROLLER
80
FLAT WASHER
M6
257
BOLT
81
BOLT
M6*40
58
MAGNETIC
RING
82
BOLT
M6*10
59
BOLT
M8*125
83
BOLT
M6*45
60
BOLT
M8*35
84
SCREW DRIVER
61
BOLT
M8*30
85
LOUDSPEAKER
62
BOLT
M10*30
86
ALLEN WRENCH
S6
63
BOLT
M5*10
87
ALLEN WRENCH
S5
64
SPRING
WASHER
M8
88
BOLT
M10*45
65
NYLON NUT
M10
89
LOCK NUT
M5
66
FLAT WASHER
9*16*t1.6
14
90
BOWL WASHER
67
FLAT WASHER
11*20*t2
18
91
BOLT
68
BOLT
ST4.2*15
16
92
COMPUTER
BOARD 1
M10*45
M8*135
Q'Y
NO.
NO.
21
DESCRIPTION
REMARK
Q'Y
6
8
M5*30
8
1
BOLT
70
MP3 WIRE
71
BOLT
72
M8*15
93
CIRCLE PLUG
94
BOLT
M10*20
95
MAGNETIC
SENSOR
BOLT
M8*60
96
SILICONE OIL
73
BOLT
M10*80
74
NYLON NUT
M8
FAULT CODE
FAULT DESCRIPTION
E1
Communication abnormal:
The control and computer
has abnormal
communication after start
Stop and go into fault. The machine cant running, the computer
shows fault code E01, and the buzzle will ringing three tone.
Explosion-Proof Protection
Stop and go into fault. The machine shows fault code E06. Other
areas show blank, and can not restart.
E2
FAULT PROCESSING
Possible Reason: Check the motor wire if connect well, and then
connect it again.
E3
E4
Check incline motor sense wire and AC wire are inserted well; AC
wire is right inserted according to the indentify in the incline motor;
make sure the incline motor wire without damager; after check
those, press the button on controller, then start self-learning again.
E5
Over-Current Protection
E6
Controller self-checking
error
22
E7
EEPROM is broken
23