Introduction
1.1
Motivation
WDM optical networks are the revolution in data transmission because of low loss,
high speed, better bandwidth and high capacity. So a lot of research is going on in
this field.
Information in the form of light transmits between transmitter and receiver in optical
communication via optical fiber. WDM provides virtual fibers, in that it makes a single Fiber
looks like multiple virtual fibers, with each virtual fiber carrying a single data stream.
Fibres also suffer from dispersion due to fibre material nonlinearities and distance the signal
travels inside the fibre. In WDM network, dispersion, Group velocity dispersion (GVD) and
nonlinear effects, such as self- and cross-phase modulation (SPM/XPM) and four-wave
mixing (FWM) is observed at different data rates. So this dispersion and non linearity has to
be minimised by some methods like using DCF, FBG, electronic equalizer, different optical
modulation format and optical phase conjugation method. Installing the DCF fibres is one of
the methods to compensate the dispersion due to single mode fibres. The DCF is analysed
with various data rate and configurations for defining the optimum results. By
introducing varieties of optical modulation formats to minimize non linearity is also analyzed
at higher data rate and different frequency spacing.
1
1.2
Literature Survey
This section includes list of literatures and research paper referred for finding project
definition, problems and its possible solution.
M. I. Hayee and A. E. Willner compare non return-to-zero (NRZ) with return-to-zero (RZ)
modulation format for wavelength-division multiplexed systems operating at data rates up to
40 Gb/s. They find that in 1040-Gb/s dispersion-managed systems (single-mode fiber
alternating with dispersion compensating fiber), NRZ is more adversely affected by
nonlinearities, whereas RZ is more affected by dispersion. In this dispersion map, 10- and 20Gb/s systems operate better using RZ modulation format because nonlinearity dominates.
However, 40-Gb/s systems favour the usage of NRZ because dispersion becomes the key
limiting factor at 40 GB/s. [1]
Anu Sheetal, AjayK.Sharma and R.S.Kaler describes the simulative analysis of 40 Gb/s long
haul (5002000 km) DWDM system with ultra high capacity up to 1.28 Tb/s has been carried
out for carrier-suppressed return-to-zero (CSRZ), duo binary return-to-zero (DRZ) and
modified duo binary return-to-zero (MDRZ) modulation formats. The DWDM system has
been analyzed for the pre, post and symmetrical dispersion compensation schemes for 16
Channels with 25GHz channel spacing in order to find the optimum modulation format for a
high bit rate optical transmission system. [2]
Bo-ning HU1, Wang Jing1, Wang Wei2 and Rui-mei Zhao1 analyzed Fiber-optic dispersion
and its effect on optical transmission system. In this paper, three schemes (pre-compensation,
post
compensation,
mix-compensation
of
dispersion
compensation)
of
dispersion
compensation with DCF are proposed. Mix-compensation gives best result among all of these
three. [3]
R.S. Kaler, Ajay K.Sharma and T.S. Kamala investigate pre-, post- and symmetrical
dispersion compensation methods for 10 Gb/s non-return to zero (NRZ) links using standard
and dispersion compensated fibers through computer simulations to optimize high data rate
optical transmission. The influence of EDFA power and increase in length of each type of
fiber has been studied to evaluate the performance of optical communication systems. [4]
Annika Dochhan, Sylvia Smolorz, Harald Rohde and Werner Rosenkranz investigate the use
of fiber Bragg gratings (FBGs) for in-line dispersion compensation in optical long-haul
wavelength division multiplex (WDM) transmission systems. They considered upgrade
scenarios contain the increase of the data rate from 10.7 Gb/s to 43 Gb/s and employment of
other modulation formats than conventional NRZ-ASK (non-return-to-zero amplitude shift
keying), such as optical duo binary (ODB) and differential phase shift keying (DPSK). [5]
Samy Ghoniemy, Karim F. George and Leonard Mac Eachern presented modelling and
design, simulation, characterization and performance evaluation of high data rate and high
capacity long-haul DWMD light wave systems. Results showed the superiority of the Duo
binary format over the other presented modulation formats. The effect of using different fiber
types (SSMF, LEAF, and TW-RS) on the proposed 42.7 Gb/s DWDM system`s performance
was discussed. The results showed that the superiority map of the different modulation
formats was changed by changing the fiber type. It was seen that using the LEAF made the
RZ-DQPSK the best modulation format of those considered. They also demonstrated that the
choice of the RZ-DQPSK modulation format over the LEAF type fiber resulted in a 50%
increase in the transmission distance of the DWDM system in spite of the reduced channel
spacing. [6]
M.D. Pelusi, F. Luan, S. J. Madden, D.-Y. Choi, D.A.P. Bulla, B. Luther-Davies and B.J.
Eggleton performed demonstration dispersion free transmission of a WDM 3 x 40 Gb/s (100
GHz spaced) using RZ-DPSK modulation format over a 162 km standard fiber link by using
optical phase conjugation via CW pumped four wave mixing in a As2S3 planar waveguide for
all channels and other approaches include using different chalcogenide glass compositions,
whose n2 can be quadruple that of As2S3. [7]
Saurabh Kumar, Prof. A. K. Jaiswal, Er. Mukesh Kumar, Er. Rohini Saxena investigated
post, pre and symmetrical/mix dispersion compensation methods for 40 Gb/s non-return to
zero link using standard and dispersion compensated fiber through FBG compensator to
optimize high data rate optical transmission. They found that fiber Bragg gratings (FBG) are
implemented instead of using dispersion compensated fiber (DCF)
for
dispersion
better
performance
matrices (Q, BER, eye pattern) for variable fiber span. But with increase in per
channel bit rate over 10Gb/s/ch viz 20 Gb/s/ch, 30Gb/s/ch and 40Gb/s/ch transmission
performance degrades on the increase of fiber length, it is much higher for 40Gb/s/ch
multiplexed optical system as compared to other systems operating on 20, 30Gb/s/ch bit
rate. They concluded by observing various results that that with increase of per channel bit
rate nonlinearities limits the fiber transmission length, while with lower bit rate system
performance parameters are very attractive, also for 40Gb/s/channel optical transmission
NRZ lacks of the necessary dispersion tolerance to accommodate. [9]
Kawal Preet Singh, Navpreet Singh, Gurinder Singh Dhaliwal have analyzed different WDM
systems using NRZ, RZ and CSRZ modulation formats and concluded that WDM system has
been effected by dispersion and non-linear effects. They also concluded that CSRZ signal is
far less sensitive to fiber Non linear effects and provides better robustness against
transmission impairments, RZ system has reduced dispersion tolerance and a reduced spectral
efficiency of RZ based WDM systems and the NRZ system has improved dispersion tolerance
but it has the effect of inter-symbol interference between the pulses this modulation format is
not suitable when high bit rates and distance. [10]
Malti, Meenakshi Sharma and Anu Sheetal have simulated 8-channel WDM-PON system for
downstream signals using carrier suppressed return-to-zero (CSRZ), duo binary return-to-zero
(DRZ) and the modified duo binary return-to-zero (MDRZ) modulation formats by varying
input power from 0 to 20 dBm for different modulation formats and found CSRZ is
superior to DRZ and MDRZ and system gives optimum performance at input power
Pin=15dBm. [11]
Rajani, Raju Pal, Vishal Sharma investigate pre, post and symmetrical-dispersion
compensation methods for 10/15Gb/s using different modulation formats like NRZ, RZ and
RZ Super Gaussian using standard and dispersion compensated fibers through computer
simulations to optimize high data rate optical transmission. It is recommended to use
symmetric- and post-DCF schemes for all the simulated optical pulses rather than using pre
DCF scheme at high transmission rate in dispersion compensated optical communication
system in conjunction with laser line width of 100 MHz. [12]
Anandita joy Agarwal, Mukesh kumar and Rohini Saxena study and compare the various
methods of dispersion compensation like Dispersion compensation fiber (DCF) which
4
compensates dispersion at 1310nm and 1550 nm and Fiber Bragg gratings (FBG) which
compensate
techniques increase the total losses nonlinear effects and costs of optical transmission system
and FBG helps in decreasing the cost of the system and also have low insertion loss. [13]
Vjaceslavs Bobrovs, Sandis Spolitis, Girts Ivanovs describes that the possible transmission
distance of the Dense WDM-PON (DWDM-PON) transmission system can be restricted by
chromatic dispersion (CD).In this paper, various chromatic dispersion compensation
techniques are compared. The best results were obtained by using FBG for CD precompensation. It is preferable to use FBG for CD compensation in pre-compensation
configuration (before SMF fiber span) in future high speed long-reach DWDM-PON systems.
[14]
M. I. Hayee and A. E. Willner describe the group velocity dispersion (GVD) and nonlinear
effects, such as self- and cross-phase modulation (SPM/XPM) and four-wave mixing (FWM)
in wavelength-division-multiplexed (WDM) systems at 10 Gb/s that degrade the performance
of the system. In this paper, 10-Gb/s WDM systems that use pre-compensation, Post
compensation or dual-compensation of each channel to minimize dispersion and nonlinear
effects are explained. [15]
J. Vojtech 1, M. Karasekt'2, J. Radill describe that the low loss of fibers, together with the
availability of erbium-doped fiber amplifiers (EDFA's), makes the 1550nm window an
attractive wavelength range of operation at 10Gb/s. However the chromatic dispersion of
SSMF is relatively large (z 17 ps/nm/km) within this window, severely limiting transmission
distances unless compensating techniques are employed. In this paper, investigation on the
transmission tolerance to signal input power launched into the link for post compensation
Scenario with fixed value of compensated CD for different compensating devices is done. CD
Compensators available were: broadband FBGs, channelized FBGs, channelized tunable
FBGs (TFBGs). Comparison of different partial CD pre-compensation schemes has been
addressed. Both fixed and channelized FBGs perform nearly identically; performance of
tunable ones is a little worse due to higher Insertion loss. [16]
Xianming Zhu, Shiva Kumar, Srikanth Raghavan, Yihong Mauro and Sergey Lobanov
describe that the Fiber-optic communication systems operating at 10 Gb/s and beyond suffer
from severe inter-symbol interference (ISI)
polarization-mode dispersion (PMD) and fiber Kerr nonlinearity. In this paper, Non-linear
Electronic dispersion compensation technique is proposed. Two different types of nonlinear
EDCs to cancel ISI caused by chromatic dispersion, nonlinearity from square-law detection,
and fiber nonlinearity are shown. [17]
Niels Neumann, Christian G. Schaffer, TU Dresden, Institut fur Nachrichtentechnik and
Dresden describes the estimation of the dispersion for different modulation formats using
nonlinear detection. [18]
Gaurang H Patel and Rohit B Patel simulate and compare dispersion compensation using DCF
and using electrical compensation (feed forward decision feedback equalizer) with data rate
of 1.28 Tb/s at fiber length of 300km. They have concluded that hybrid dispersion
compensation gives better performance than other compensation scheme. It means hybrid
compensation provides three times performance enhancement than mix optical compensation
scheme. [19]
Majid Moghaddasi and Assoc.Prof. Dr. Syuhaimi Bin Ab. Rahman compares the efficiency of
on-off Keying (OOK) modulation formats non-return-to-zero (NRZ) and return-to-zero (RZ)
in both electrical (using feed forward-decision feedback equalizer (FFEDFE) method) and
optical chromatic dispersion compensation (using Dispersion Compensation Fiber (DCF)) and
concluded that in electrical compensation NRZ seems predominate in most parts of the route
compare to RZ 0.67 while RZ 0.5 produces the worst performances almost at all points but in
optical compensation RZ modulation with both duty cycle (0.67 and 0.5) gives us definitely
much better performance than NRZ especially in shorter distances. [20]
Vjaceslavs Bobrovs, Sandis Spolitis
compensate using DCF or FBG as a dispersion compensate module for WDM PON network
for 16 channels each with 10 Gb/s.They concluded that by implementation of DCF fiber in
DCM unit the 16 channel DWDM-PON systems maximal link length between OLT and
ONT in pre-compensation configuration improved by 19.3% or 11 km in length from 57
km to 68 km, but in post-compensation configuration by 5.3% or 3 km in length from 57 km
to 60 km and by implementation of fiber Bragg grating pre-compensation solution in
dispersion compensation module DWDM passive optical network transmission line can
be improved by 26.3% or additional 15 km in length from 57 km till 72 km, but using
fiber Bragg grating in post-compensation solution transmission line can be improved by
15.8% or additional 9 km in length started from 57 km till 66 km. [21]
1.3
Thesis Organization
Chapter 2
2.1 Overview
The world telecommunication consists two parts: the Greek word tele which means the over
a distance, and communication which means the exchange of information. We can define
telecommunication as Exchange of information over a certain distance using some type of
medium.
One of these mediums that really had a big impact on data transmission was coaxial-cable
system. The first coaxial-cable system, deployed in 1940, was a 3MHz system which could
transmit 300 voice channels [33]. But these coaxial-cables, they mostly suffer from high cable
losses and repeater spacing is also very limited and is costly for a longer transmission length.
And these shortcomings led to the development of microwave communication system.
Microwave communication system uses electromagnetic carrier waves in the range of GHz to
transmit signals with different techniques to modulate the carrier waves. The microwave
communication system allowed larger repeater spacing but suffered from limited bit rate.
As we begin the new millennium, we are seeing dramatic changes in the telecommunications
industry that have far-reaching implications for our lifestyles. There are many drivers for
these changes. First and foremost is the continuing, relentless need for more capacity in the
network. This demand is fueled by many factors like growth of internet and the World Wide
Web, both in terms of number of users and the amount of time, and thus bandwidth taken by
each user, is a major factor.
The Shannon-Hartley theorem states that information carrying capacity is proportional to
channel bandwidth, the range of frequencies within which the signals can be transmitted
without substantial attenuation. [32]
The frequency of the carrier signal limits the bandwidth. The higher the carrier frequency, the
greater the channel bandwidth and the higher the information carrying capacity of the system.
Fiber optical communication system use light as a carrier with the highest frequency among
all the practical signals and this is what makes these systems the linchpin of modern
telecommunications.
Then Optical fiber was first developed in the 1970s, which revolutionized the
telecommunications industry and played a major role in the Information era. Because of its
advantages over electrical transmission, optical fibers have largely replaced copper wire
communications in core networks in the developed world [34]. Optical communication
system use high carrier frequency (~100 THz) in the visible or near infrared region of the
electromagnetic spectrum. Because of its low loss, high capacity and capacity it become more
popular [32].
Consider the following statement from a leading telecommunication provider The explosive
growth of Internet traffic, deregulation and the increasing demand of users are putting
pressure on our customers to increase the capacity of their network. Only optical networks can
deliver the required capacity and the bandwidth-on-demand is now synonymous with
wavelength-on demand.
2.2.1 Transmitter
The role of an optical transmitter is to convert the electrical signal into optical form and to
launch the resulting optical signal into the optical fiber. Fig. 2.1 shows the block diagram of
an optical transmitter. It consists of an optical source, a modulator, and an information signal
as an input signal. Semiconductor lasers or light-emitting diodes are used as optical sources
because of their compatibility with the optical-fiber communication channel. The optical
signal is generated by modulating the optical carrier wave with information signal (electrical
form).Then resulting modulated optical signal pulse propagates through optical fiber.
2.2.2 Receiver
An optical receiver converts the optical signal received at the output end of the optical fiber
back into the original electrical signal. Fig. 2.1 shows the block diagram of an optical receiver.
It consists of an optical detector, and a demodulator. Semiconductor photodiodes are used as
photo detectors because of their compatibility with the whole system which converts optical
signal to electrical signal and demodulator is used to convert modulated signal to information
signal.
10
11
Second way to increase the capacity is by a technique called wavelength division multiplexing
(WDM). WDM is essentially the same as frequency division multiplexing (FDM), which has
been used in radio systems for more than a century. For some reason, the term FDM is used
widely in radio communication, but WDM is used in the context of optical communication.
The idea is to transmit data simultaneously at multiple carrier wavelengths (or, equivalently,
frequencies or colors) over a fiber. To first order, these wavelengths do not interfere with each
other provided they are kept sufficiently far apart. Thus WDM provides virtual fibers, in that
it makes a single Fiber looks like multiple virtual fibers, with each virtual fiber carrying a
single data stream. WDM systems are widely deployed today in long-haul and undersea
networks and are being deployed in metro networks as well.
2.4.2 Transparency
WDM networks supports data to be transmitted at different bit rates. It also supports a number
of protocols. So there is not much constraint in how we want to send the data. So it can be
used for various very high speed data transmission applications.
2.4.4 Scalability
12
WDM networks are also very flexible in nature. As per requirement we can make changes to
the network. Extra processing units can be added to both transmitter and receiver ends. By
this infrastructure can redevelop to serve more number of people.
2.4.5 Reliability
WDM networks are extremely reliable and secure. Here chance of trapping the data and
crosstalk is very low. It also can recover from network failure in a very efficient manner.
There is provision for rerouting a path between a source-destination node pair. So in case of
link failure we will not lose any data.
Wavelength
Division
Multiplexing
(WDM)
impact
transmission
performance. Nonlinear effects play a major role in optical fiber with respect to transmission
capacity and performance of the system.
Impairments in optical fiber are broadly classified in to two categories: linear and non-linear
impairments. The terms linear and non-linear in fiber optics mean intensity-independent and
intensity-dependent, respectively. The linear impairments are static in nature and non-linear
impairments are dynamic in nature. The non-linear impairments strongly depend on the
current allocation of route and wavelength, i.e., on the current status of allocated light paths.
Linear impairments are independent of the signal power and affect each of the wavelengths
(optical channels) individually, whereas nonlinear impairments affect not only each optical
channel individually but they also cause disturbance and interference between them.
13
noise figure (NF) value, which is the ratio of the optical signal to noise ratio (OSNR) before
the amplification to the same ratio after the amplification and is expressed in dB.
Chromatic dispersion causes pulse broadening, which affects the receiver performance by:
(1) Reducing the pulse energy within the bit slot
(2) Spreading the pulse energy beyond the allocated bit slot leading to inter-symbol
interference (ISI). CD can be adequately (but not optimally) compensated for on a
per link, and/or at transmission line design time.
PMD is not an issue for most type of fibers at 10 Gb/s, however it become an issue at 40 Gb/s
or higher rates. In general, in combination with PMD there is also polarization dependent loss
(PDL). It can cause optical power variation, waveform distortion and signal-to-noise ratio
fading.
2.5.1.1 Power Losses
Power loss can be defined as the optical loss that is accumulated from source to destination
along fiber links and is normally made up of intrinsic fiber losses and extrinsic bending
losses. Intrinsic fiber losses are due to attenuation, absorption, reflections, refractions,
Rayleigh scattering, optical component insertion losses, etc. Let
at the input of a fiber of length L; then the output power
PT
P0
is given by
L
PT =P 0e
(2.1)
Where is the fiber attenuation coefficient.
14
The loss introduced by the insertion of optical components, such as couplers, filters,
multiplexers/ de multiplexers, and switches, into the optical communications system is called
insertion loss and is usually independent of wavelength.
The extrinsic losses are due to micro and macro bending losses. Additional losses occur due to
the combined effects of dispersion resulting from inter symbol interference (ISI), mode
partition noise, and laser chirp as discussed later in this section.
2.5.1.2 Chromatic Dispersion (CD)
Df Lf + D C LC =0
dispersion slopes of CD and DCF, some wavelengths may be over-compensated and some
others may be under compensated.
Moreover DCF modules may only be available in fixed lengths of compensating fiber. Hence,
sometimes it may be difficult to find a DCF chat exactly compensates the CD introduced by
the fiber, leading to residual CD. A typical value of dispersion compensation tolerance in
15
commercial receivers is around 800 ps/nm for non-return-to-zero (NRZ) 10 Gb/s, while it is
160 ps/nm for optical duo binary (ODB) 40 Gb/s.
2.5.1.3 Polarization Mode Dispersion (PMD)
induced pulse broadening is relatively small compared to CD. The PMD on a fiber link is a
function of PMD on each fiber-span. The PMD values vary from fiber to fiber in the range of
0.01-10 ps/
km . PMD becomes a major limiting factor for WDM systems designed for
longer distances at higher bit-rates. The effect of second and higher order PMD becomes
prominent at high-bit rates exceeding 40 Gb/s. PMD induced problems can be reduced by
shortening the optical transmission distance by placing OEO regenerators between two optical
nodes. However, as most long-haul DWDM systems are multi-wavelength, the transmission
link must first be demultiplexed, then regenerated, and then multiplexed again, which is a very expensive
operation. Another alternative is to use dispersion compensation modules (DCM) at optical
add/drop multiplexers (OADMs), optical cross-connects (OXCs), or amplifier sites to
compensate for accumulated PMD on an optical path. Because PMD effects are random and
16
For an ultra short pulse with a Gaussian shape and constant phase, the intensity at time t is
given by I(t):
17
I ( t )=I 0 exp (
t 2
)
2
(2.2)
Where
I0
the peak intensity and is is half the pulse duration. If the pulse is travelling in a
medium, the optical Kerr effect produces a refractive index change with intensity:
n ( I ) =n0 +n2 I
(2.3)
Where n0 is the linear refractive index and n2 is the second-order nonlinear refractive index of
the medium.
As the pulse propagates, the intensity at any one point in the medium rises and then falls as
the pulse goes past. This will produce a time-varying refractive index:
dn(I )
dI
2 t
t 2
=n2 =n2 I 0
exp
(
)
dt
dt
2
2
( )
(2.4)
This variation in refractive index produces a shift in the instantaneous phase of the pulse:
( t )=w0 tkx=w0 t
Where
w0
and
2
n(I )L
0
(2.5)
are the carrier frequency and (vacuum) wavelength of the pulse, and L
d
2 L dn(I )
=w0
dt
0 dt
(2.6)
and from the equation for dn/dt above, this is:
18
w ( t )=w0 +
4 L n2 I 0
0
t 2
exp
(
)
2
t
(2.7)
Plotting (t) shows the frequency shift of each part of the pulse. The leading edge shifts to
lower frequencies ("redder" wavelengths), trailing edge to higher frequencies ("bluer") and
the very peak of the pulse is not shifted. For the centre portion of the pulse (between t = /2),
there is an approximately linear frequency shift (chirp) given by:
w ( t )=w0 +t
(2.8)
Where is:
=
dw 4 L n2 I 0
=
dt
0 2
It is clear that the extra frequencies generated through SPM broaden the frequency spectrum
of the pulse symmetrically. In the time domain, the envelope of the pulse is not changed,
however in any real medium the effects of dispersion will simultaneously act on the pulse. In
regions of normal dispersion, the "redder" portions of the pulse have a higher velocity than
the "blue" portions, and thus the front of the pulse moves faster than the back, broadening the
pulse in time.
Hence, the primary effect of SPM is to broaden the pulse in the frequency domain, keeping
the temporal shape unaltered. As the chirping effect is proportional to the transmitted signal
power, the SPM effects are more pronounced in systems with high transmitted power. SPM is
the strongest among the Kerr effects for DWDM systems working at 100GHz spacing. The
chirp also depends on the input pulse shape. The appropriate chirping of input signals using
chirped RZ (CRZ) modulation can reduce the SPM effects. The effects produced by nonlinear
SPM and linear dispersion are opposite in nature. By proper choice of pulse shape and input
power, one effect will compensate for another, leading to undistorted pulse in both time and
frequency domains. Such a pulse is called a Soliton pulse and is useful in high-bandwidth
optical communication systems.
2.5.2.2 Cross-Phase Modulation (XPM)
The non-linear refractive index seen by an optical pulse depends not only on the intensity of
the pulse but also on the intensity of the other co- propagating optical pulses, i.e., the
19
20
dispersion-shifted fibers are normally used in WDM systems. Another way to reduce FWM
effect is to employ unequal channel spacing in such a way that the generated signals do not
interfere with the original signals.
2.5.2.4 Stimulated Brillouin Scattering (SBS)
SBS occurs when an optical signal in fiber interacts with the density variations such as
acoustic phonons and changes its path. In SBS, the scattering process is stimulated by photons
with a wavelength higher than the wavelength of the incident signal.SBS is recognized as the
most dominant fiber non-linear scattering effect. SBS sets an upper limit on the amount of
optical power that can be launched into an optical-fiber.
When input optical power exceeds the SBS threshold, a significant amount of the transmitted
light is redirected back to the transmitter leading to saturation of optical power in the receiver,
and introducing noise that degrades the BER performance. The SBS threshold depends on the
line-width of the optical source, with narrow line-width sources having considerably lower
SBS thresholds. The back-scattered signals can be measured using a Fabry-Perot
interferometer or pump probe or self-heterodyne techniques. Externally modulating the
transmitter provides one way to broaden the line-width of the optical source. Hence, it is
particularly important to control SBS in high-speed transmission systems that use external
modulators and continuous wave (CW) laser sources.
2.5.2.5 Stimulated Raman Scattering (SRS)
In WDM systems, if two or more optical signals at different wavelengths are injected into a
fiber, the SRS effect causes optical signal power from lower wavelength optical channels to
be transferred to the higher wavelength optical channels. This can skew the power distribution
among the WDM channels- reducing the signal-to-noise ratio of the lower wavelength
channels and introducing crosstalk on the higher wavelength channels.
Both of these effects can lower the information carrying capacity of the optical transmission
system. SRS occurs at significantly higher optical powers than SBS, with threshold powers of
the order of watts for SRS compared to mW for SBS. Unlike SBS, SRS scatters in both
forward and reverse directions. The effect of SRS, i.e., Raman gain co-efficient, can be
measured using relative cross-section method or pulse-scanning technique or Raman
amplification method. Several optical filtering techniques are proposed to suppress SRS
interactions in optical fiber systems. The filters, when inserted appropriately into the
21
transmission link, can effectively suppress the SRS power flow from the WDM channels to
lower frequency noise. Furthermore, usage of a high-pass filter can enhance the SRS
threshold in an optical fiber.
i | A 2| A +
2
|A 2|
i (| A | A)
T R A
w0
T
T
(2.10)
Where T is a frame of reference moving with the pulse at the group velocity and
T =t
z
=t 1 z
,
vg
| A2|
vg
and
1 , 2 3
22
w0
TR
is related to the
slope of the Raman gain and is usually estimated to be ~5 fs. Equation (2.1.1) includes the
effects of fiber loss through , of chromatic dispersion through linear delay
nonlinear effects through
vg
, of
higher order of dispersion which becomes important for ultra-short pulses. The last two terms
on the right-side of the equation
are related to the effects of stimulated inelastic scattering such as SRS and SBS.
Equation (2.1.1) is a nonlinear partial differential equation which generally does not have an
analytical solution except for some special cases. A numerical approach is needed to
understand the nonlinear effects in fibers most of time. Many of simulators use Split-Step
Fourier Transform (SSFT) to simulate the evolution of optical waveform over fiber. In a
standard SSFT method, fiber span is divided into many short sections and the dispersion
operator and the nonlinear operator are treated separately in each section (Ref. [6]). If were
write the Equation (2.1.1) like this (Ref. [2, 6]):
A (z , T )
=( D+ N ) A
z
(2.11)
Where D and N are dispersion operator and nonlinear operator respectively. They are given
by:
D=
i
2 1
3
2
+
3
2
T 2 6 T 3 2
(2.12)
N=i | A 2|+
(| A2| A)
| A 2|
T R
w0 A
T
T
i
(2.13)
From Equation (2.1.2), we can get the evolution of the complex optical field along the fiber
from one section to the next section:
23
A ( z+ hn ,T ) =exp ( hn N ) exp ( hn D ) A ( z ,T )
Where,
hn
th
(2.14)
fiber section.
exp ( hn D )
Where
D (iw ) = 2 w2
2
2
(2.15)
F1
denote the Fourier and inverse Fourier transformations respectively. Finally, for SSFT
numerical method, the equation for the optical field evolution can be written as following:
A ( z+ hn ,T ) =exp ( hn N ) F 1 {exp ( h n D(iw ) ) F [ A ( z , T )]}
(2.16)
In Equation (2.1.7), the dispersion acts with optical signal first in frequency domain, and
nonlinear effects interfere with optical signal in time domain separately. In general, the
simulation using SSFT starts with the known wave format the transmitter A(0,T) and finds the
optical field of each consecutive fiber section till the end of the transmission.
24
Chapter 3
3.1. Introduction
To increase the capacity of light wave systems, or bit rate-distance product, high speed data
rate per channel and close channel spacing in DWDM systems are the possible solutions.
10Gb/s or 40Gb/s DWDM system would be the next generation of light wave systems. In
such high speed DWDM systems, linear and nonlinear impairments become severe. Those
linear impairments include chromatic dispersion (CD), and first order polarization mode
dispersion (PMD); nonlinear impairments include self-phase modulation (SPM), cross-phase
modulation (XPM) and four-wave mixing (FWM) as discussed in previous chapter. To
compensate both the linear and the nonlinear impairments over the transmission fiber, an
optimal modulation format is desired: A modulation format with narrow optical spectrum can
enable closer channel spacing and tolerate more CD distortion; A modulation format with
constant optical power can be less susceptible to SPM and XPM; A modulation format with
multiple signal levels will be more efficient than binary signals and its longer symbol duration
will reduce the distortion induced by CD and PMD. In addition, in an optical repetitive
amplified light wave system, amplified spontaneous emission (ASE) noise is another concern
which requires modulation formats more tolerant to additive ASE noise. There have been
many optical modulation formats in the scope of this researching area. Because of its easy to
modulate and demodulate, most of them are binary signaling, e.g. duo binary, VSB/SSB, RZ,
phase-shift-keying (PSK) etc.. While, others are multi-level signaling, e.g. differentialQuadra-phase-shift-keying (DQPSK), and M-PAM etc.. It is impossible to cover all of those
modulation formats in this thesis. However, we will detail and compare several very
important modulation formats often used in recent years. The modulation formats covered in
this thesis are NRZ-OOK, RZ-OOK, CS-RZ, MDRZ and DRZ. Although this is not a
complete screening of the advanced optical modulation formats arena, the results in this thesis
and the mechanism under each modulation format are still valuable and can be extended for
the future research. In the following part, the basic waveform generation/detection and major
25
characteristics of these five modulation formats will be discussed. It will form a foundation
for the following parts of the thesis where system performance of different modulation
formats will be detailed.
(a)
(b)
(c)
Fig. 3.1 NRZ (a) Schematic diagram of NRZ transmitter (b) time domain (c) frequency
domain visualize
For a long time, non-return-to-zero on-off-keying (NRZ-OOK) has been the dominant
modulation format in IM/DD fiber-optical communication systems. For convenience we
would like to refer NRZ-OOK as NRZ. There are probably several reasons for using NRZ in
the early days of fiber-optical communication: First, it requires a relatively low electrical
bandwidth for the transmitters and receivers (compared to RZ); second, it is not sensitive to
laser phase noise (compared to PSK); and last, it has the simplest configuration of
transceivers. In recent years, as optical amplifiers, NRZ modulation format may not be the
best choice for high capacity optical systems. However, due to its simplicity, and its historic
dominance, NRZ would be a good reference for the purpose of comparison.
26
The block diagram of a NRZ transmitter is shown in Fig. 3.1(a), where electrical signal is
modulated with an external intensity modulator. The intensity modulator can be either MachZehnder type or electro-absorption type, which converts an OOK electrical signal with data
rate of Rb into an OOK optical signal at the same data rate. The optical pulse width of each
isolated digital 1 is equal to the inverse of the data rate. To detect a NRZ optical signal, a
simple photodiode is used at the receiver, which convert s optical power of signal into
electrical current. This is called direct detection (DD). If there is no mention, same direct
detection scheme is used for other modulation formats. Fig. 3.1 (b), (c) shows the spectrum of
NRZ with10Gbps of data rate. In general, NRZ modulated optical signal has the most
compact spectrum compared to that with other modulate formats. However, this does not
mean that NRZ optical signal has superior resistance to residual chromatic dispersion in an
amplified fiber system with dispersion compensation. Also this does not mean NRZ is more
tolerant to XPM and FWM in crowded DWDM systems because of its strong carrier
component in the optical spectrum [36]. In addition, NRZ optical signal has been found to be
less resistive to GVD-SPM effect in transmission compared to its RZ counterparts. A simple
explanation is that different data patterns in a PRBS NRZ data stream require different
optimum residual dispersion for the best eye opening. For example, an isolated digital 1
would generate more self-phase modulation (SPM) effect than continuous digital 1s.Since
SPM can be treated as an equivalent signal frequency chirp; it modifies the optimum value of
the dispersion compensation in the system. The difference in the optimum dispersion
compensation between an isolated digital 1 and continuous digital 1s makes it impossible
to optimize the residual dispersion in the system and thus makes the system performance
vulnerable to the data patent-dependent fiber nonlinear effect. This effect is especially
important in long distance fiber-optic systems.
3.2.2. RZ-OOK
(a)
27
(b)
(c)
Fig. 3.2 RZ (a) Schematic diagram of RZ transmitter (b) time domain (c) frequency domain
visualize
RZ means return-to-zero, so the width of optical signal is smaller than its bit period. Usually
a clock signal with the same data rate as electrical signal is used to generate RZ shape of
optical signals. Fig. 3.2(a) shows the block diagram of a typical RZ transmitter. First, NRZ
optical signal is generated by an external intensity modulator; then, it is modulated by a
synchronized pulse train with the same data rate as the electrical signal using another intensity
modulator. RZ optical signal has been found to be more tolerant to nonlinearity than NRZ
optical signal. The reason for its superior resistance to nonlinearity than NRZ is probably due
to its regular data pattern of optical signal. Because of characteristic of return-to-zero of RZ
optical signals, an isolated digital bit 1 and continuous digital 1s would require the same
amount of optimal dispersion compensation for the best eye opening. So with the optimal
dispersion compensation in the system, RZ format shows better tolerance to nonlinearity than
NRZ. The spectrum of RZ is also shown in Fig. 3.2 (b), (c). Compared to NRZ, it has a wider
spectrum because of its narrower pulse width. This would lead to less spectrum efficiency for
RZ in a WDM system.
3.2.3. CS-RZ
28
(a)
(b)
(c)
Fig. 3.3 CSRZ (a) Schematic diagram of CSRZ transmitter (b) time domain (c) frequency
domain visualize
In general, the generation of a CS-RZ optical signal requires two electro-optic modulators as
shown in Fig. 3.3(a). In this configuration, the first intensity modulator encodes the NRZ data.
Then the generated NRZ optical signal is modulated by the second intensity modulator to
generate a CS-RZ optical signal. The second intensity modulator is biased at the minimum
power transmission point and driven by a sinusoidal clock at the half data rate of the electrical
signal. As illustrated in Fig. 3.3(b), a MZ intensity modulator biased at this condition doubles
the frequency of the modulating signal and the phase of output pulse train is alternated
between 0 and . This configuration only requires half data rate of bandwidth for the
second electro-optical modulator, which reduces the complexity of configuration. CS-RZ has
shown better tolerance to fiber nonlinearity and residual chromatic dispersion in recent
research. Its RZ intensity bit pattern makes it easy to find the optimum dispersion
compensation. In addition, carrier suppression reduces the efficiency of four wave-mixing in
WDM systems.
3.2.4. DRZ
29
(a)
(a)
(b)
(c)
Fig. 3.4 DRZ (a) Schematic diagram of DRZ transmitter (b) time domain (c) frequency
domain visualize
Fig. 3.4(a) illustrates the schematic of the 40 Gb/s duo-binary transmitter. The duo binary
was generated by first creating an NRZ duo binary signal using a duo binary precoder,
NRZ generator and a Duo binary pulse generator. The generator drives the first MZM, and
then cascades this modulator with a second modulator that is driven by a sinusoidal
0
electrical signal with the frequency of 40GHz Phase = - 90 . The duo binary precoder
used here is composed of an exclusive-or gate with a delayed feedback path. DRZ formats
are very attractive, because their optical modulation bandwidth can be compressed to the
data bit rate B, that is, the half-bandwidth of the NRZ format 2B as shown in Fig. 3.4(b),
(c).
3.2.5 MDRZ
30
(a)
(b)
(c)
Fig. 3.5 MDRZ (a) Schematic diagram of MDRZ transmitter (b) time domain (c) frequency
domain visualize
Duo binary data encoding has received much attention because of its advantages in
dispersion tolerance and reducing nonlinear effects in optical communication systems
[38]- [40]. Relative to non-return-to-zero (NRZ) format optical signals, return-to-zero
(RZ) format optical signals can tolerate high input power, and have small inter-symbol
interference and high receiver sensitivity [41]. Recently it has been shown [38], that
modified duo binary RZ (MD-RZ) signals show more advantages compared to regular
RZ, duo binary RZ, and alternating phase RZ signals because the MD-RZ has an
opposite-phase in the adjacent 1s, which leads to the fact that self-phase modulation in
single channel, cross-phase modulation and intra-channel four-wave mixing in WDM
transmission systems can be reduced. In a conventional scheme, generation of the duo- binary
31
RZ usually needs two modulators; one is used to generate duo binary signals and the other is
cascaded to this modulator for carving NRZ signals to generate RZ signals.
Fig. 3.5(a) displays the schematic for the production of the MDRZ modulation format. In
this, first NRZ duo-binary signal is generated that drives the first MZM and then
connecting this modulator with a second modulator that is driven by a sine wave
generator with the frequency of 40GHz and phase -95. Fig. 3.5(b), (c) shows the optical
spectrum of MDRZ signal. The generation of MDRZ signal is almost identical to the
DRZ signal, except the delay -and-add circuit is replaced by a delay-and subtract circuit. In
the duo binary signal used earlier where the phase of bits '1's are modified only after a bit
'0' appear whereas in the modified duo binary signal the phase is alternated between 0
and for the bits 1. The phase of all the "zero" bits is kept constant and a
phase variation between all the consecutive "ones" is introduced.
32
1800
Chapter 4
4.1 Introduction
In WDM networks optical fibers are employed to transmit information in form of light pulse
between the transmitter and the receiver. WDM systems have the potential to transmit
multiple signals simultaneously. But the light signals degrade in intensity when they travel a
long distance inside the fiber. Fibers suffer from dispersion and other nonlinearities due to
fiber material nonlinearities and distance the signal travels inside the fiber. In WDM network,
dispersion, Group velocity dispersion (GVD) and nonlinear effects, such as self- and crossphase modulation (SPM/XPM) and four-wave mixing (FWM) is observed at different data
rates.
To support a high-capacity wavelength-division-multiplexing (WDM) transmission, the
embedded standard single-mode fiber (SMF) should be upgraded to overcome the dispersion
limit. For this purpose, some dispersion compensation scheme must be employed periodically
at the amplification stages. There are several different methods that can be used to
compensate for dispersion, including dispersion compensating fiber (DCF), fiber Bragg
gratings, optical phase conjugation and electrical dispersion compensation.
33
(4.1)
Where, D and L are the dispersion and length of each fiber segment, respectively.
34
Pre-Compensation:
The optical communication system is pre compensated by the dispersion compensating fiber
of negative dispersion against the standard fiber. In pre-compensation, the dispersion
compensating fiber is placed before standard single mode fiber.
Post-Compensation:
The optical communication system is post compensated by the dispersion compensating fiber
of negative dispersion against the standard fiber. In post compensation, the dispersion
compensating fiber is placed after standard single mode fiber.
Mix-Compensation:
The optical communication system is symmetrically compensated by the dispersion
compensating fiber of negative dispersion against the standard fiber. This scheme is
combination of the pre and post compensation scheme.
The diagram of Pre, Post and Mix dispersion compensation is shown in following figure:
(a)
(b)
35
(c)
Fig. 4.1 (a) Pre, (b) Post and (c) Symmetrical/Mix Compensation
36
longer wavelength (red) as shown in fig.4.2, this wavelength-dependent time delay can be
used to compensate for dispersion.
37
In a mid-link OPC transmission link, the phase of the signals is conjugated mid-link. At
that point, the signal is severely distorted by chromatic dispersion and nonlinear impairments.
As a result, the distortions that occur in the second part of the link after the OPC,
revert the impairments that were accumulated in the first part. Full compensation for
nonlinear impairments occurs when the nonlinear effects before and after OPC are identical.
The use of mid-link OPC is twofold. Firstly, mid-link OPC can compensate for impairments
caused by the Kerr-effect. The Kerr effect causes a change in the refractive index of the
transmission fiber in response to an electric field. In fiber-optic transmission systems, the Kerr
effect leads to distortions in the phase of the signals and can significantly reduce the system
performance. Through the compensation for Kerr-effect, the feasible transmission distance is
significantly extended and the amount of required OEO repeaters reduced. Secondly, OPC can
be used to compensate for chromatic dispersion. In such a link, no inline DCF modules are
required. The omission of DCFs translates into reduced losses per span, which enables
the use of single stage amplifiers instead of two stage amplifiers required in DCF-based
transmission systems. As a result, mid-link OPC enables a simplified and cost efficient
amplifier design. The block diagram of mid-link OPC is shown in figure below.
A more cost-effective solution is to use mid-link OPC. In this configuration OPC is used for
both chromatic dispersion compensation and compensation of the Kerr-effect. Hence no inline
DCF modules are used in this configuration. Instead the dispersion accumulates along the
transmission line and is compensated for by placing an OPC mid-link.
Since the dispersion accumulates linearly along the fiber-optic transmission link, OPC must
be placed exactly in the middle of link to obtain full dispersion compensation. This way the
distortion that occurred in the first part of the transmission link before the OPC is cancelled
by distortions that occur in the second part of the link after the OPC. It should be mentioned
that it is not always possible to place OPC exactly in middle of fiber transmission link.
Therefore an extra DCF module can be employed to obtain full chromatic dispersion
compensation.
The propagation of a signal in a nonlinear, dispersive and lossy medium can be expressed by
the nonlinear Schrodinger equation assuming a slowly varying envelope approximation [23]
2
A
i 2 A 1 3 A
=
A 2
+ 3
+i | A| A
2
3
z
2
2 T 6 T
38
(4.2)
where A represents the complex amplitude of the signal, z the propagation distance in km,
the attenuation coefficient in neper per kilometer, the nonlinearity coefficient (Kerr effect) in
1/(Wkm), and T = t z/vg the time measured in a retarded frame. 2 in ps2/nm and 3 in
ps3/nm are terms for the group velocity dispersion (GVD) and dispersion slope, respectively.
Its complex conjugate can be expressed as [23]
2
A i 2 A 1 3 A
=
A + 2
+ 3
i| A | A
2
3
z
2
2
6
T
T
(4.3)
Where * denotes the complex-conjugate operation. Note that in this equation the signal
evolution over the fiber after conjugation is still denoted by A. In this expression, it can be
seen that the sign of the chromatic dispersion term (2) and the Kerr effect term () are both
inverted. The chirp induced through GVD increases linear along the transmission link. Since
the sign of the GVD term is inverted by OPC, the GVD induced chirp that occurs after OPC
cancels the GVD induced chirp before OPC. Thus, in a transmission link with the same fiber
before and after OPC, full GVD compensation is obtained by placing the OPC mid-link.
39
Signal
Generati
on
Optical
Trasmitte
r
Transmiss
ion Link
Optical
Reciver
EDC
d k
N2
n N1
*
n
y k n
40
(4.4)
Where
C*n
d k
41
d k
N2
n N1
*
n
N3
y k n Fi d k i
i 1
(4.5)
Where
C*n
d k
and yn is the input received signal. Fi is the tap gain for feedback filter and di is the previous
decision made on detected signal.
42
Chapter 5
43
Simulation setup:
FOR
5.1.1
S
r.
1
2
3
4
Parameter
Value
Data rate
Wavelength
Power
Modulation formats
No. of iterations
6
7
Frequency spacing
No. of channels
Attenuation
Dispersion
Dispersion slope
Differential group
delay
44
70 m
Aeff
N2
Raman contribution
26E-21 m^2/W
0.18
DCF
Attenuation
Dispersion
Dispersion slope
Differential group
delay
0.5 dB/km
-0.85 ps/nm/km
-3 ps/nm^2/k
0.2 ps/km
Aeff
22 m 2
N2
Raman contribution
26E-21 m^2/W
0.18
Multiplexer
Idle
1
0
1
1
De-multiplexer
1
2
EDFA
1
3
Results:
TABLE 5.2 FOR NRZ AT 16X10 GBPS DATA RATE
Sr.
No.
With nonlinearity
P
EYE
avg.
Height
126
59.3
235
131.7
350
224.2
470
273.1
550
320.2
680
360
760
462.8
860
443.7
9
10
1020
1100
494.2
525.8
ECP
3.2731
59
2.5148
21
1.9343
24
2.3577
62
2.3494
14
2.7620
64
2.1542
02
2.8740
9
3.1469
74
3.2057
45
Without nonlinearity
P
EYE
avg.
Height
ECP
3.40353
134
61.2
4
2.24813
245
146
2
1.75409
350
233.7
3
1.53555
460
323
3
1.39714
570
413.2
5
670
504.2
1.23472
780
595.7
1.17067
880
687.5
980
1100
779.8
872.3
1.0721
0.99242
8
1.00726
21
34
200
105.7
285
173.1
390
219.6
460
293.2
550
371.1
610
428.5
680
492.3
760
573.9
10
820
619
239.9
460
310.5
545
382
630
454
710
526.6
800
600
880
673
0.
30
0.
00
1
00
00
0
00
00 .2
00
03
2
0.
60
0.
00
4
0
00
0.
70
00
00
00 0.5
00
00
00
00
00
64
00
00
06
2
6
5
4
3
2
NRZ with N.L
1
0
ECP(dB)
375
1.94001
1.70696
2
1.54333
1
1.42284
7
1.29777
5
1.24938
7
1.16467
6
RZ without N.L
1
108
0.
9
ECP
5.0194
48
2.7695
5
2.1654
78
2.4943
23
1.9559
39
1.7087
17
1.5337
9
1.4027
91
1.2197
74
1.2212
32
Without nonlinearity
P
EYE
avg.
Height
ECP
4.80817
118
39
4
2.98916
205
103
6
2.30673
290
170.5
6
0.
8
Sr.
No.
With nonlinearity
P
EYE
avg.
Height
RZ with N.L.
Fig. 5.2 ECP for NRZ, RZ with and without Non-Linearity at 10 Gbps
TABLE 5.4 FOR NRZ AT 16X20 GBPS DATA RATE
Sr.
No.
1
With nonlinearity
P
EYE
avg.
Height
ECP
165
23.9
8.3908
46
Without nonlinearity
P
EYE
avg.
Height
ECP
140
39.5 5.49530
6
2
285
91.2
400
163.6
510
238.6
620
315.2
730
392.8
840
471.2
940
550.2
1050
629.6
10
1160
709.4
4.9485
3.8827
67
3.2989
97
2.9380
55
2.6915
14
2.5107
4
2.3260
73
2.2212
46
2.1356
68
265
103.2
390
160
515
212.5
575
304.7
655
369
820
411.7
1040
418.1
1070
479.1
1070
525.8
9
4.09566
2
3.86944
6
3.84448
3
2.75795
4
2.49214
9
2.99233
3.95753
2
3.48957
6
3.08563
2
With nonlinearity
P
EYE
avg.
Height
160
10
260
41.9
350
95.4
440
152
530
210.7
620
270.8
690
331.9
785
393.9
870
456.5
10
960
519.7
ECP
12.041
2
7.9275
93
5.6451
97
4.6160
91
4.0061
13
3.5974
3
3.1784
18
2.9948
37
2.8007
85
2.6651
85
47
Without nonlinearity
P
EYE
avg.
Height
ECP
12.2393
139
8.3
7
5.02675
210
66
4
4.38103
300
109.4
9
4.14401
410
157.9
7
3.02576
450
224.2
9
2.64886
560
304.3
1
2.61615
640
350.4
9
3.39253
800
366.3
1
2.88838
850
437.1
1
2.10222
860
530
6
0.
9
0.
8
RZ with N.L.
0.
0.
60
4
00
00
0.
00
0.
70
00
5
00
00
00
00
00
06
00
4
00
00
06
2
0.
0.
30
1
00
00
00
0.
00
2
00
00
03
2
ECP(dB)
14
12
10
8
6
4
2
0
RZ without N.L.
Fig. 5.3 ECP for NRZ, RZ with and without Non-Linearity at 20 Gbps
TABLE 5.6 FOR NRZ AT 16X40 GBPS DATA RATE
Sr.
No.
With nonlinearity
P
EYE
avg.
Height
160
46.5
290
118.5
405
198
520
279.1
610
363.9
740
413.2
840
473.7
950
522.9
1075
553.8
10
1200
613.1
ECP
5.3666
7
3.8867
96
3.1078
98
2.7024
35
2.2434
78
2.5307
14
2.4877
59
2.5930
5
2.8805
55
2.9164
99
Without nonlinearity
P
EYE
avg.
Height
ECP
5.17310
155
47.1
8
3.56547
275
121
3
2.99931
395
198
9
510
276.6
630
356.1
740
436.3
860
517.1
980
598.2
1100
679.6
1210
761.4
2.65718
2.47768
6
2.29446
5
2.20923
9
2.14379
7
2.09139
3
2.01172
5
With nonlinearity
P
EYE
avg.
Height
98
165
1.1
27.2
ECP
19.498
33
7.8291
48
Without nonlinearity
P
EYE
avg.
Height
ECP
14.7488
97
3.25
8
165
32.9
7.00288
220
56.7
280
91.3
330
128.3
375
174
420
216.6
480
259.8
530
300
10
600
342.7
5
5.8883
96
4.8668
73
4.1028
73
3.3348
2
2.8759
08
2.6660
21
2.4715
46
2.4323
71
225
66.3
285
101.4
345
137.6
400
174.4
465
211.8
520
249.6
580
287.6
640
326
5.30669
4.48806
9
3.99200
7
3.60513
5
3.41527
3.18758
8
3.04639
1
2.92962
4
25
20
15
10
NRZ without
N.L.
5
RZ with N.L.
1
0.
9
0.
8
0
0.
30
0.
1
00
00
00
0.
00
2
00
00
03
2
0.
60
0.
00
4
00
0.
00
70
0.
00
00
5
0
00
00
00
00
00
64
00
00
06
2
ECP(dB)
RZ without N.L.
Fig. 5.4 ECP for NRZ, RZ with and without Non-Linearity at 40 Gbps
Results Discussion:
In 10- and 20-Gb/s systems, the eye closure penalty is large for lower channel powers because
the EDFA noise is dominant [See Fig. 5.2 and 5.3]. For higher channel powers, the eye
closure penalty decreases since the signal power now overcomes the EDFA noise. However, at
the highest channel powers being considered, the eye closure penalty increases as a function
of power due to nonlinearity. The penalty due to nonlinearity is more severe in NRZ as
compared to RZ. Since RZ performs better than NRZ in both 10 and 20 Gb/s systems, we can
conclude that RZ is less affected by nonlinearity than is NRZ. This is because: 1) isolated RZ
pulses take advantage of Soliton-like pulse compression in SMF, whereas the variable number
of adjacent 1s in NRZ are non uniformly degraded by nonlinearity, thereby causing the rail
49
FOR
5.1.2
Parameter
Value
Data rate
Modulation format
Duty cycle
10 GBPS
NRZ and RZ
0.5 bit for RZ
50
4
5
Wavelength
Power
SMF
Attenuation
Dispersion
Dispersion slope
PMD
0.2 dB/km
16 ps/nm/km
0.016 ps/nm^2/k
0
2
70 m
Aeff
N2
Length
26E-21 m^2/W
70 to 160 km
DCF
Attenuation
Dispersion
Dispersion slope
PMD
0.6 dB/km
-90 ps/nm/km
-0.075 ps/nm^2/k
0
Aeff
22 m 2
N2
Length
EDFA
26E-21 m^2/W
12.4 to 28.4 km
NF: 4 dB
15 dB for different length of SMF FOR 1
span
Variable as a function of length of DCF
for 1 span
GAIN
GAIN
9
0.75*Bit rate
Results:
This paper compares the efficiency of on-off Keying (OOK) modulation formats non-returnto-zero (NRZ) and return-to-zero (RZ) in optical chromatic dispersion compensation using
DCF. I got the following result.
TABLE 5.9 RESULTS FOR DIFFERENT LENGTH OF SMF
Length of
SMF(km)
70
80
90
100
110
NRZ
BERNRZ
1.40E22
6.30E22
1.30E21
3.00E22
7.50E22
51
RZ 0.5
BER-RZ
0.5
RZ 0.67
BER-RZ
0.67
0.00E+00
0.00E+00
0.00E+00
0.00E+00
0.00E+00
0.00E+00
0.00E+00
0.00E+00
0.00E+00
0.00E+00
8.00E21
7.80E19
2.60E16
1.50E12
1.00E08
120
130
140
150
160
2.50E247
2.40E109
4.80E-271
1.40E-120
2.40E-47
2.40E-52
1.10E-20
2.60E-22
1.90E-09
6.30E-10
15
0
13
0
11
0
-5
90
70
0
-10
-15
log10(BER)
-20
NRZ
-25
RZ 0.5
-30
RZ 0.67
-35
-40
-45
Length of SMF (km)
52
Simulation setup:
FOR
5.1.3
Parameter
Value
Data rate
Wavelength
Modulation formats
10 GBPS
1550 nm
NRZ
SMF
Attenuation
Dispersion
Dispersion slope
4
0.2 dB/km
16 ps/nm/km
0.016 ps/nm^2/k
2
88 m
Aeff
N2
26E-21 m^2/W
PMD
0.1 ps/
km
DCF
5
Attenuation
Dispersion
Dispersion slope
Aeff
0.6 dB/km
-80 ps/nm/km
-0.075 ps/nm^2/k
59 m
53
N2
26E-21 m^2/W
PMD
0.1 ps/
km
EDFA
0.75*Bit rate
Note: The values of Non linear co-efficient is given in the paper as following:
1
1
= 1.2 W km
for SMF
1
= 1.8 W km
And from
for DCF
2 n2
A eff
for DCF
Results:
In this paper, they investigate pre-, post- and symmetrical-dispersion compensation methods
for 10 Gb/s non-return to zero (NRZ) links using standard and dispersion compensated fibers
through computer simulations to optimize high data rate optical transmission. The influence
of EDFA power and increase in length of each type of fiber has been studied to evaluate the
performance of optical communication systems. Further, it has also been observed that system
needs proper matching between the EDFA power and length of the fiber for optimum
performance. Also, they increase simultaneously the lengths of dispersion compensated fibers
and standard single mode fibers in the original setups for pre-, post- and symmetrical
compensation methods for five different cases as shown in following Tables.
TABLE 5.11 RESULTS FOR DIFFERENT POWER LEVEL
POWER(d
Bm)
0
BERPost
1.70E-50
1.40E-95
3.90E144
1.80E127
4
6
BER-Pre
5.00E-59
1.70E116
3.80E153
5.10E105
54
BERSymmetrical
1.30E-43
2.20E-70
3.00E-103
1.40E-128
8
10
12
4.30E-60
2.00E-21
1.20E-07
0
-5
3.00E-44
3.00E-14
4.80E-04
1.90E-120
1.60E-78
3.00E-37
10
12
-10
-15
log10(BER)
-20
-25
BER-Post
-30
BER-Pre
BER-Symmetrical
-35
-40
-45
Input Optical Power (dBm)
Fig. 5.8 Bit error rate vs. fixed output power of EDFA for pre-, post- and symmetrical
compensation methods
2
3
5.70E-82
7.30E-33
2.20E-09
SMF LENGTH
BERPost
3.00E298
4.00E110
CASE
EDFA POWERS
BERPre
BERSymmetrical
0
7.00E96
4.00E52
2.60E27
5.30E05
0
0
0
1.00E-155
2.00E-20
EDFA Power(dBm)
0
3
55
DCF
3
4
5
6
9
12
18
24
30
0
1
-5
-10
-15
log10(BER) -20
-25
-30
-35
-40
-45
90
120
150
BER-Post
BER-Pre
BER-Symmetrical
CASE #
Fig. 5.9 Bit error rate for different cases indicated in Table 5.12 for pre-, post- and
symmetrical compensation methods
TABLE 5.14 DIFFERENT
CASE
1
2
3
4
5
BERPost
4.50E51
1.00E30
1.20E14
4.00E10
3.60E04
BERPre
1.00E53
5.30E27
3.30E11
5.80E07
4.10E02
LENGTHS
FOR
BERSymmetrical
1.20E-102
3.60E-68
1.80E-42
1.90E-20
6.10E-15
56
0
-5
1 2 3 4 5
-10
-15
log10(BER) -20
-25
BER-Post
BER-Pre
-30
BER-Symmetrical
-35
-40
-45
CASE #
Fig. 5.10 Bit error rate for different cases indicated in Table 5.14 for pre-, post- and
symmetrical compensation methods
Results Discussion:
From the simulation results, it is found that as the EDFA power increases, the bit error rate
increases. The symmetrical compensation has the best performance followed by post- and precompensation. Also, the influence of transmission distance on the three compensation
methods has been discussed by simultaneously increasing the lengths of fibers and keeping
the EDFA power constant. As the lengths of the fibers are increased, the bit error rate
increases. The bit error rate for symmetrical compensation method is again minimum but for
pre- and post-compensation methods, the situation is not so good. For acceptable bit error rate
of 10^-12 , the maximum transmission distance for post-compensation is up to 288 km
whereas it is approximately up to 216 km for pre compensation method for this simulation.
Further, on varying the EDFA power and lengths of the fibers simultaneously, it is found that
there is need of optimization between these two parameters. If the EDFA power is small, the
length of the fiber should be small and if it is not so, the situation will deteriorate on account
of more nonlinear effects. For less EDFA power over larger length of the fiber, the situation
will be worse as predicted. This reflects the need of optimization and there should not be any
mismatch between the EDFA power and length of the fiber.
57
FOR
5.1.4
S
r.
1
2
3
4
5
6
7
Parameter
Value
Data rate
Wavelength
Power
Modulation formats
No. of iterations
Frequency spacing
No. of channels
Attenuation
Dispersion
Dispersion slope
Differential group delay
SMF
0.22 dB/km
17 ps/nm/km
0.016 ps/nm^2/k
0.2 ps/km
2
80 m
Aeff
N2
Raman contribution
30E-21 m^2/W
0.18
DCF
Attenuation
Dispersion
0.55 dB/km
-0.8 ps/nm/km
58
Dispersion slope
Differential group delay
-0.076 ps/nm^2/k
0.2 ps/km
Aeff
20 m 2
N2
Raman contribution
25E-21 m^2/W
0.18
Bandwidth:
75 GHz
Depth:
100 dB
Filter type: Gaussian
Order:
2
Bandwidth: 75 GHz
Depth: 100 dB
Filter type: Gaussian
Order: 2
SMF: Gain=17.6 dB
NF=5 dB
DCF: Gain=4.675 dB
NF= 5 dB
1
0
8 x 1 Multiplexer
1
1
De-multiplexer
1
2
EDFA
1
3
90 GHz
Results:
TABLE 5.17 RESULTS OF TRANSMISSION
POWER(d
Bm)
0
1
2
3
4
5
6
7
8
9
10
11
12
Q
post
15.2
16.7
17.9
19.1
19.6
20.1
19.5
18.9
17.8
16.5
15.2
13.8
11.4
Q pre
12.1
14.1
15.6
18.1
19.5
20.7
21.6
20.1
18.7
16.7
14.2
11.4
9.1
59
Q
symmetric
al
14.9
15.9
17.8
19.9
19.6
20.1
20.3
22.1
25.7
26.1
22.5
20.1
16.6
30
25
20
Q value
15
Q post
10
Q pre
Q symmetrical
5
0
Power (dBm)
60
Parameter
Value
Data rate
Wavelength
Modulation formats
Compensation scheme
Span
SMF
Attenuation
Dispersion
Dispersion slope
0.22 dB/km
17 ps/nm/km
0.016 ps/nm^2/k
2
80 m
Aeff
N2
30E-21 m^2/W
DCF
Attenuation
Dispersion
Dispersion slope
0.55 dB/km
-0.80 ps/nm/km
-0.076 ps/nm^2/k
61
20 m 2
Aeff
N2
25E-21 m^2/W
SMF: Gain=11 dB
NF=4 dB
DCF: Gain=5.844 dB
NF= 4 dB
EDFA
0.7*Bit rate
Results:
TABLE 5.19 RESULTS FOR NRZ AT 10 GBPS SINGLE
LINK
10GBPS @500km
POST
PRE
POWER(dB
m)
-7
12
15.
5
18.
7
19.
5
16.
6
11.
8
8.2
5.8
-5
-3
-1
1
ECP
5.45298
9
Q
11.
8
4.86949
4.52940
2
4.48977
2
4.80867
2
15
17.
6
17.
5
13.
4
5.13772
5.87679
5
7.30284
1
8.1
4.3
6.23921
9.98884
7
Q
14.
2
18.
8
24.
1
29.
3
35.
3
42.
2
30.
6
#NUM!
9.4
ECP
SYMMETRICA
L
5.62132
4.95895
3
4.66900
4
4.72006
1
5.02675
4
AT
10 GBPS SINGLE
ECP
5.146062
4.633121
4.176623
3.976988
3.751686
3.815478
4.266126
6.306046
LINK
10GBPS @500km
POST
PRE
POWER(dB
m)
-1
Q
10.
3
13.
7
17.
9
22.
7
28
-7
-5
-3
ECP
5.70170
8
4.95726
5
4.37448
5
4.04876
5
3.86460
2
Q
10.
3
13.
5
17.
4
21.
9
27.
2
62
SYMMETRICA
L
ECP
ECP
5.8039
5.00135
6
4.54613
9
4.14539
3
12
15.
8
20.
4
25.
6
31.
1
5.44068
3.88818
4.806378
4.272294
3.994719
3.859884
3
5
7
33.
2
36.
7
30.
4
3.55387
7
3.64552
2
3.69063
9
33.
6
42.
3
50.
2
(a)
(b)
(c)
63
3.70017
3
3.52575
4
3.44890
7
36.
4
44.
2
61.
5
3.717571
3.539959
3.608306
Fig. 5.14 ECP and Q factor of the single channel versus average-power for NRZ and RZ
systems at 10 Gbps (a) Per (b) Post (c) Symmetrical compensation scheme
TABLE 5.21 RESULTS FOR NRZ AT 20 GBPS SINGLE
LINK
20GBPS @500km
POST
PRE
POWER(dB
m)
-7
9.5
-5
-1
12
13.
9
13.
3
8.7
3
5
4.5
2.2
1.2
-3
ECP
5.95673
2
5.37236
9
4.95726
5
5.27778
2
6.46212
10.0960
6
#NUM!
5.26048
8
SYMMETRICA
L
Q
ECP
8.7
11.
5
14.
9
18.
7
22.
5
19.
3
8.6
6.114909
7.6
2.6
ECP
5.88898
5
5.09745
7
4.63618
8
4.60784
5
5.12106
5
6.57128
9
#NUM!
#NUM!
3.1
20.25285
9.7
12.
8
16.
1
18
14.
7
AT
20 GBPS SINGLE
5.320221
4.727999
4.355141
4.119257
4.281618
5.791971
LINK
20GBPS @500km
POST
PRE
POWER(dB
m)
-7
6.5
-5
8.8
11.
8
15.
6
19.
7
21.
7
18.
5
-3
-1
1
3
5
ECP
7.51822
3
6.27614
1
5.42817
1
4.77403
4
4.37758
4.16108
8
4.35660
5
Q
8.4
11.
2
14.
8
18.
8
22.
6
23.
6
18.
9
64
ECP
6.58436
5
5.57092
8
4.92915
5
4.47627
8
4.16254
9
4.12449
4
4.24897
7
SYMMETRICA
L
Q
ECP
7.4
6.819367
9.8
12.
8
16.
9
21.
9
28.
4
34.
6
5.789947
5.055046
4.5176
4.232081
3.88732
3.678428
13.
2
4.83169
4
12.
7
5.05227
2
31.
9
3.658107
(a)
(b)
(c)
Fig. 5.15 ECP and Q factor of the single channel versus average-power for NRZ and RZ
systems at 20 Gbps (a) Per (b) Post (c) Symmetrical compensation scheme
TABLE 5.23 RESULTS FOR NRZ AT 40 GBPS SINGLE
65
LINK
40GBPS @250km
POST
PRE
POWER(dB
m)
ECP
6.0206
9.1
11.
5
13.
8
14.
7
12.
3
8.4
9.5
12.
3
15.
4
17.
3
16.
1
12.
3
4.9
-7
-5
-3
-1
5.38673
4.92915
5
4.81351
8
5.07735
4
5.93459
8
8.62248
6
8.2
ECP
6.29889
1
5.47702
3
4.88116
6
4.59244
7
4.74091
8
5.0289
6.25782
4
SYMMETRICA
L
Q
ECP
9.4
12.
1
15.
1
17.
7
17.
4
5.856696
13
4.87246
7.6
6.076451
5.173463
4.760369
4.465919
4.621809
LINK
40GBPS @250km
POST
PRE
POWER(dB
m)
-7
-5
-3
-1
1
3
5
Q
8.2
10.
7
13.
6
16.
7
19.
4
19.
2
15.
9
ECP
6.30615
5
5.41362
2
4.81212
4.47627
8
4.31494
8
4.24363
2
4.50404
9
Q
8
10.
5
13.
7
17.
3
21.
3
23.
8
22.
8
66
ECP
6.27614
1
5.37119
2
4.78973
3
4.32957
1
4.06411
9
3.88151
8
3.93539
SYMMETRICA
L
Q
ECP
7.6
6.320232
10
5.409968
13
16.
5
20.
4
4.817662
24
23.
7
3.976299
4.475151
4.142372
4.034029
(a)
(b)
(C)
Fig. 5.16 ECP and Q factor of the single channel versus average-power for NRZ and RZ
systems at 40 Gbps (a) Per (b) Post (c) Symmetrical compensation scheme
5.2.1.2 Performance comparison between DCF and DCF + Equalizer for Dispersion
67
Compensation
Simulation setup:
10 GBPS
No. of Span:
(a)
68
(b)
Fig. 5.18 Eye diagram for single channel (10 Gbps) using (a) DCF (b) DCF +
Equalizer at 1250 km at 0 dBm
TABLE 5.25 PERFORMANCE COMPARISON
FOR
LINK
Sr. No.
1
2
Compensation Scheme
DCF
DCF + Equalizer
BER
1.1 E -12
0
69
IN SINGLE
Q
7
140.5
Data rate:
10 GBPS
No. of Span:
Results:
TABLE 5.26 RESULTS FOR COHERENT AND DIRECT DETECTION
AT
NRZ
RZ
-2
Coherent
Q
cohere
BER
nt
3.80E-34
12.1
2.60E-56
15.8
4.40E-87
19.7
4.50E135
24.7
7.50E152
26.2
5.30E-73
18
6.70E-26
10.5
4.00E-03
2.61
4.80E-64
1.30E114
1.60E181
1.70E208
2.80E189
2.70E128
4.10E-54
Power(d
Bm)
-10
-8
-6
-4
Direct
BER
4.00E-13
2.80E-23
6.10E-37
Q
direc
t
7.1
9.9
12.6
16.8
Coherent
Q
cohere
BER
nt
1.90E-24
10.1
6.00E-39
13
7.60E-64
16.8
BER
9.00E-12
1.60E-19
1.20E-32
Q
direc
t
6.7
8.9
11.8
20.3
4.00E-58
16
23.6
20.5
28.7
30.78
2.10E-68
17.4
29.3
3.90E-29
11.1
24
9.30E-06
4.3
15.4
1.80E-93
1.40E152
5.30E196
7.00E248
2.60E281
8.20E290
22.7
22.4
RZ
Q valueQcoherent
40
40
30
30
Qdirect
20
Qcoherent
Q value
Qdirect
20
10
-10
Direct
2.80E-92
2.30E123
3.70E111
NRZ
-15
10 GBPS
-5
0
0
10
5
-15
-10
-5
0
0
(a)
(b)
Fig. 5.20 Power vs. Q value for single link (10 Gbps) using coherent and direct detection
(a) NRZ (b) RZ
70
26.3
30
33.6
35.8
36.4
5.2.1.4 Performance Comparison of Single link using different types of fiber for 40 Gbps
Data rate for NRZ and RZ
Parameters: Same as TABLE 5.18
Data rate:
40 GBPS
No. of Span:
OF ALL KINDS OF
FIBER [42]
Results:
TABLE 5.28 Q VALUES OF DIFFERENT
POWER (dBm)
-7
-5
-3
-1
1
3
5
40 GBPS Link @
NRZ
Q
Q
SSM
Q
TWF
TW
RS
8.6
8.8
8.8
11.3 11.5
11.5
14.1 14.7
14.8
14.9 18.4
18.7
11.3 21.5
22.2
5.9
23.2
23.5
2.4
23
21.5
71
NRZ
AND
RZ
250 km
RZ
Q
LEA
F
8.6
11.3
14.7
18.9
23.2
26.5
27.2
Q
SSM
F
7.2
9.6
12.5
16.1
20.2
22.1
17.3
Q
TW
7
9.2
12.1
15.8
20.8
27.5
37
Q
TWRS
7.5
9.8
12.7
16.2
20.1
24.1
25.9
Q
LEA
F
7.3
9.6
12.6
16.1
20.5
25.9
32.6
NRZ
RZ
30
40
25
30
20
SSMF 15
Q value
10
TW
TW-RS
LEAF
TW-RS
LEAF
10
5
0
SSMF 20 TW
Q value
-7
-5
-3
-1
Power (dBm)
-7 -5 -3 -1
Power (dBm)
(a)
(b)
Fig. 5.21 Power vs. Q value for single link (40 Gbps) using different fibers
Results Discussion:
From the above simulation results symmetrical compensation scheme performance is the best
than pre and post scheme. As data rate increases performance degrades and as power increases
up to certain limit performance enhance and then degrades due to non linearity as power
increase. RZ performs better comparatively NRZ for higher power level at all data rates. I
introduced many techniques like DCF and DCF+Equalizer and among these two,
DCF+Equalizer gives higher Q value at 1250 km for 10 Gbps and 0 dBm power level using
NRZ modulation. We also observed that direct detection using DCF performs better than
direct detection using DCF for NRZ and RZ at 10 Gbps data rate for lower input optical
power level. We also used different types of cable like SSMF, TW, TW-RS and LEAF and
analyzed that LEAF performs better at higher power level in NRZ modulation and TW and
LEAF performs better in RZ at 10 Gbps data rate.
72
Parameter
Value
Data rate
Wavelength
Power
Modulation formats
No. of iterations
Frequency spacing
No. of channels
Compensation
scheme
Attenuation
Dispersion
Dispersion slope
Differential group
delay
0.2 dB/km
17 ps/nm/km
0.075 ps/nm^2/k
0.2 ps/km
2
70 m
Aeff
N2
Raman contribution
26E-21 m^2/W
0.18
DCF
73
1
0
1
1
Attenuation
Dispersion
Dispersion slope
Differential group
delay
0.5 dB/km
-0.85 ps/nm/km
-3 ps/nm^2/k
0.2 ps/km
Aeff
22 m 2
N2
Raman contribution
26E-21 m^2/W
0.18
Multiplexer
Idle
1
2
De-multiplexer
1
3
EDFA
1
4
Results:
TABLE 5.30 Q VALUES FOR DIFFERENT MODULATION FORMATS 200 GH Z SPACING
40GBPS System NRZ,RZ 0.5,RZ 0.67CSRZ,DRZ,MDRZ for
200GHz spacing
RZ
CSR
NRZ RZ0.5
0.67
Z
DRZ MDRZ
POWER(dBm)
Q
Q
Q
Q
Q
Q
nrz
rz0.5 rz0.67 csrz
drz
mdrz
-15
3.8
0
2.6
2.6
2.1
0
-10
7.2
3.8
5.1
5.4
4.4
3.9
-5
12.6
7
8.8
11
8.3
7.8
0
17.8
12.5
18.5
12.1 15.5
14
5
11.8
18.2
17.6
13
23
20.1
10
0
10.4
5.8
5.7
10
16
74
10
RZ0.5
RZ 0.67
CSRZ
DRZ
MDRZ
5
0
-15
-10
-5
10
Fig. 5.23 Power vs. Q for 8-channel (320 Gbps) using different modulation formats at 200
GHz spacing
TABLE 5.31 Q VALUES FOR DIFFERENT MODULATION FORMATS 100 GH Z SPACING
40GBPS System NRZ,RZ 0.5,RZ 0.67CSRZ,DRZ,MDRZ for
100GHz spacing
RZ
CSR
NRZ RZ0.5
0.67
Z
DRZ MDRZ
POWER(dBm)
Q
Q
Q
Q
Q
Q
nrz
rz0.5 rz0.67 csrz
drz
mdrz
-15
3.5
2.7
3.7
3.8
3.1
2
-10
6
5.7
7
7.5
6
4.1
-5
8.5
10.8
11.1
13.8 11.6
7.5
0
10.4
18.5
14.6
22.3 19.9
14.4
5
8.3
23.9
16.8
22.7 19.8
23
10
0
10.1
4.3
4.9
9.3
16.2
RZ 0.67
CSRZ
DRZ
MDRZ
5
0
-15
-10
-5
75
10
Fig. 5.24 Power vs. Q for 8-channel (320 Gbps) using different modulation formats at 100
GHz spacing
5.2.2.2 Performance comparison between DCF (direct detection), DCF + Equalizer and
DCF (coherent detection) for 8-channel WDM Link
Simulation Setup:
No. of Span:
76
(a)
2. Using DCF (coherent detection) for 100 km at 0 dBm Power level
(b)
3. Using DCF + Equalizer for 100 km at 0 dBm Power level
77
(c)
Fig. 5.26 Eye diagram for 8-channel (320 Gbps) (a) Using DCF (direct detection) (b) Using DCF
(coherent detection) (c) DCF + Equalizer
Compensation Scheme
DCF (coherent detection)
DCF (direct detection)
DCF + Equalizer
FOR
8-CHANNEL
BER
2 E -38
3.1 E -109
0
Q
12.9
22.2
83.76
Results Discussion:
we have simulated 8 channel 40 Gb/s WDM channel with 100 and 200 GHz spacing over
300 km transmission distance using various modulation formats like NRZ, RZ 0.5, RZ
0.67, CSRZ, DRZ and MDRZ and analyzed performance
symmetrical
of
the
system
for
the
outcome of the analysis is that for different power level and channel spacing, each
modulation format gives the different performance. For 200 GHz spacing, NRZ gives better
for lower power level up to 0 dBm but for higher power level MDRZ and DRZ gives the best.
For 100 GHz spacing, CSRZ gives better for lower power level up to 5 dBm but for higher
power level RZ 0.5 and MDRZ have the superior performance. We have also analyzed each
modulation formats for 100 and 200 GHz spacing. For 200 GHz spacing, NRZ for all power
level, RZ 0.67 for moderate power level and DRZ for higher power level gives better than 100
GHZ spacing. For 100 GHZ spacing, RZ 0.5, CSRZ and MDRZ gives better for all power
level but RZ 0.67 and DRZ gives better Q value for low power level. We also analyzed the
78
performance for DCF+Equalizer, DCF using coherent and DCF using direct detection and
DCF+Equalizer performance is best among these three techniques.
FOR
5.2.3
Parameter
Value
Data rate
Wavelength
Power
Modulation formats
No. of iterations
Frequency spacing
No. of channels
Compensation
79
scheme
SMF
Attenuation
Dispersion
Dispersion slope
Differential group
delay
0.2 dB/km
17 ps/nm/km
0.075 ps/nm^2/k
0.2 ps/km
2
70 m
Aeff
N2
Raman contribution
26E-21 m^2/W
0.18
DCF
1
0
1
1
Attenuation
Dispersion
Dispersion slope
Differential group
delay
0.5 dB/km
-0.85 ps/nm/km
-3 ps/nm^2/k
0.2 ps/km
Aeff
22 m 2
N2
Raman contribution
26E-21 m^2/W
0.18
Multiplexer
Idle
1
2
De-multiplexer
1
3
EDFA
1
4
Results:
TABLE 5.34 Q VALUE USING
POWER(
mw)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
DIFFERENT
Q
nrz
4.3
8.3
7.5
7.4
8.9
8.4
7.5
8.1
6.7
6.6
Q
rz
2.3
3.5
4.7
5.7
6.5
6.2
5.5
6
6.3
6.2
80
MODULATION
Q
mdrz
2.8
3.6
4.2
4.5
4.6
4.5
5.4
5.5
5.8
6.5
FORMAT FOR
Q
drz
2.7
3.9
4.6
5
5.03
5.2
5.4
6
5.7
5.2
Q
csrz
3.4
4.5
6.1
6.5
6.2
5.8
5.8
6.1
6.2
5.5
1.28 TBPS
10
9
8
7
6
5
4
3
2
Q value
1
Q nrz 0
Q rz
Q mdrz
Q drz
Q csrz
POWER(m
w)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
log(BER
) nrz
5.2
15.4
13.7
13.5
18.8
16.7
13.7
15.9
11.0
DIFFERENT
log(BER
)
rz
2.0
3.7
6.0
8.4
10.4
9.7
7.8
9.0
9.9
MODULATION
-log(BER)
mdrz
2.7
3.8
4.9
5.4
5.7
5.6
7.6
7.7
8.5
81
FORMAT FOR
log(BER
)
drz
2.5
4.3
5.7
6.6
6.7
7.0
7.6
8.9
8.3
1.28 TBPS
log(BER)
csrz
3.6
5.6
9.2
10.4
9.5
8.5
8.5
9.5
9.6
1.0
10.9
20
18
16
14
12
10
8
-log(BER) nrz
6
4
2
-log10 (BER)
0
9.7
10.4
-log(BER) rz
7.0
-log(BER) mdrz
7.9
-log(BER) drz
-log(BER) csrz
TABLE 5.36 ECP (dB) VALUE USING DIFFERENT MODULATION FORMAT FOR 1.28 TBPS
POWER(
mw)
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
ECP(dB)
NRZ
7.3
3.5
3.6
3.5
2.8
3.0
3.5
3.2
ECP(dB)
RZ
ECP(dB)M
DRZ
ECP(dB)
DRZ
12.4
7.8
6.3
6.0
6.1
6.7
6.2
9.6
8.3
7.6
7.1
6.7
5.5
6.1
8.2
6.1
5.9
6.2
6.7
7.1
6.7
82
ECP(dB)C
SRZ
11.5
6.7
4.7
4.5
4.6
4.8
4.7
4.7
0.9
1.0
3.6
3.8
5.8
5.8
5.3
5.0
6.6
6.7
4.8
5.1
14.0
12.0
10.0
8.0
6.0
ECP(dB)NRZ
ECP(dB)RZ
ECP(dB)MDRZ
ECP(dB)DRZ
4.0
ECP(dB)
2.0
0.0
ECP(dB)CSRZ
83
Chapter 6
6.1
Conclusion
Our main objective of this dissertation is to reduce dispersion and non linearity. In this work,
we have investigated the performance of single link and WDM link at different data rates and
frequency spacing using different optical modulation formats like NRZ-OOK, RZ-OOK,
CSRZ, DRZ and MDRZ and analyzed the results for single channel, 8 channels and 32
channels.
From analysis for single channel the conclusion is as following. Symmetrical compensation
scheme performance is the best than pre and post scheme. As data rate increases performance
degrades and as power increases up to certain limit performance enhance and then degrades
due to non linearity as power increase. RZ performs better comparatively NRZ for higher
power level at all data rates. I introduced many techniques like DCF and DCF+Equalizer and
among these two, DCF+Equalizer gives higher Q value at 1250 km for 10 Gbps and 0 dBm
power level using NRZ modulation. We also observed that direct detection using DCF
84
performs better than direct detection using DCF for NRZ and RZ at 10 Gbps data rate for
lower input optical power level. We also used different types of cable like SSMF, TW, TW-RS
and LEAF and analyzed that LEAF performs better at higher power level in NRZ modulation
and TW and LEAF performs better in RZ at 10 Gbps data rate.
For 8-channel (8 x 40 Gb/s = 320 Gbps) WDM link with 100 and 200 GHz spacing over
300 km transmission distance using various modulation formats like NRZ, RZ 0.5, RZ
0.67, CSRZ, DRZ and MDRZ and analyzed performance
symmetrical
of
the
system
for
the
outcome of the analysis is that for different power level and channel spacing, each
modulation format gives the different performance. For 200 GHz spacing, NRZ gives better
for lower power level up to 0 dBm but for higher power level MDRZ and DRZ gives the best.
For 100 GHz spacing, CSRZ gives better for lower power level up to 5 dBm but for higher
power level RZ 0.5 and MDRZ have the superior performance. We have also analyzed each
modulation formats for 100 and 200 GHz spacing. For 200 GHz spacing, NRZ for all power
level, RZ 0.67 for moderate power level and DRZ for higher power level gives better than 100
GHZ spacing. For 100 GHZ spacing, RZ 0.5, CSRZ and MDRZ gives better for all power
level but RZ 0.67 and DRZ gives better Q value for low power level. We also analyzed the
performance for DCF+Equalizer, DCF using coherent and DCF using direct detection and
DCF+Equalizer performance is best among these three techniques. Only disadvantage is that
it introduces jitter effect because of the equalizer.
For 32-channel (32 x 40 Gb/s = 1.28 Tbps) WDM link with 100 GHz spacing over 500 km
transmission distance using various optical modulation formats and concluded that NRZ gives
best performance than all other modulation formats those I have introduced in terms of Q
value, BER and ECP.
85
formats like NRZ-DPSK, RZ-DPSK, OFDM, and QPSK in the same link and analyze the
results.
References
[1]
[2]
Transmission Systems, IEEE Photonics Technology Letters, vol. 11, pp.991-993, August 1999.
Anu Sheetal et al., Simulation of high capacity 40 Gb/s long haul DWDM system using different
86
modulation formats and dispersion compensation schemes in the presence of Kerrs effect, Science
[3]
[4]
[5]
Gb/s NRZ links using standard and dispersion compensated fibers, Optics Communications, 2002.
Annika Dochhan et al., FBG Dispersion Compensation in a 43 Gbit/s WDM System: Comparing
[6]
[7]
[8]
Conjugation in As2S3Glass.
Saurabh Kumar et al., Performance Analysis of Dispersion Compensation in Long Haul Optical Fiber
with DCF, IOSR-JECE,e-ISSN: 2278-2834, ISSN: 2278-8735. vol. 6, Issue 6, pp. 19-23, Jul. - Aug.
[9]
2013.
Devendra Kr.Tripathi et al, Comparative Performance Study in 32 Multiplexed Channels Optical
Transmission in Bit Rates 10, 20, 30,40Gbps with NZDSF, IJSCE , ISSN: 2231-2307, vol.-1, Issue-5,
[10
]
[11
]
[12
]
November 2011.
Er. Kawal Preet Singh et al., Performance Analysis of different WDM systems, IJEST, ISSN : 09755462 vol. 4 No.03 March 2012.
Malti et al., Comparison of CSRZ, DRZ and MDRZ Modulation Formats for High Bit Rate WDMPON System using AWG, International Journal of Emerging Technology and Advanced
Engineering ,ISSN 2250-2459, vol. 2, Issue 6, June 2012.
Rajani et al., Comparison of Pre-, Post- and Symmetrical-Dispersion Compensation Schemes for
10/15Gbps using Different Modulation Formats at Various Optical Power Levels using Standard and
Dispersion Compensated Fibers, International Journal of Computer Applications (0975 8887) vol.
[13
]
[14
]
[15
]
[16
]
[17
]
[18
]
[19
]
[20
]
87
[21
]
[22
]
[23
]
[24
]
[25
]
[26
]
[27
]
[28
]
[29
]
[30
]
[31
]
[32
]
[33
]
[34
]
[35
]
[36
]
[37
]
[38
]
[39
]
[40
]
Vjaceslavs Bobrovs et al., Comparison of Chromatic Dispersion Compensation Techniques for WDMPON solution, IEEE, 2nd Baltic Congress on Future Internet Communications, 2012.
Sander Lars Jansen.Optical phase conjugation in fiber-optic transmission systems, Eindhoven :
Technische Universiteit Eindhoven, 2006.
S. L. Jansen, Student Member, IEEE et al., Long-Haul DWDM Transmission Systems Employing
Optical Phase Conjugation, IEEE Journal Of Selected Topics In Quantum Electronics, vol. 12, NO. 4,
Aug. - 2006.
M. S. O'Sullivan et al.,Electronic Dispersion Compensation Techniques for Optical Communication
Systems, ECOC, 2005.
Theodore s. Rappaport, Wireless communication Principle and Practice, Second Edition.
Shi Yuhu, Research on the dispersion problem in High Speed Optical Communication Systems,
IEEE 2011
Fariborz Mousavi Madani et al., Design Theory of Long-Distance WDM Dispersion-Managed
Transmission System, Journal Of Lightwave Technology, vol. 17, NO. 8, AUG 1999
Jin-Xing Cai, Senior Member, IEEE, et al., Transmission of 40-Gb/s WDM Signals Over
Transoceanic Distance Using Conventional NZ-DSF With Receiver Dispersion Slope Compensation,
Journal Of Light wave Technology, vol. 24, NO. 1, JAN 2006.
Daniel Fonseca et al., Use of Electrical Pre-compensation of Dispersion in Optical Single-Sideband
Transmission Systems IEEE Journal Of Selected Topics In Quantum Electronics, vol. 12, NO. 4,
july/aug-2006.
J. Vojtech et al, Comparison of an Unconventional All-Optical Chromatic Dispersion Compensation
Techniques in Nothing in Line Scenarios with Emphasis to Tunability IEEE 2007.
Cheng-Chun Chang et al.,Fiber Transmission for Sub-500-fs Pulses Using a DispersionCompensating Fiber IEEE Journal Of Quantum Electronics, vol. 33, NO. 9, sept. 1997.
Djafar K. Mynbaev and Lowell L. Scheiner, Fiber-optic communication technology(1st
edn),Pearson,pp. 19-24,2012.
John M. Senior, Optical fiber communications principles and practice(2 nd edn), Pearson,pp. 1-2,2006.
Rajiv Ramaswami and Kumar N. Sivarajan and Galen H. Sasaki,Optical Networks-A practical
perspective(3rd edn),Morgan kaufman,pp. 1,2012.
Govind P. Agrawal,Fiber-Optic Communication Systems(3rd edn),John Wiley & Sons.
Chris Xu et al., Comparison of return-to-zero differential phase-shift keying and on-off keying in
long-haul dispersion managed transmission, IEEE photonics technology letters, vol. 15, NO. 4, pp.
617-619, April 2003.
A. Hirano, et,al., 320 Gbit/s (840 Gbit/s) WDM transmission over 367-km zero-dispersion-flattened
line with 120-km repeater spacing using carrier suppressed return-to-zero pulse format, OSA TOPS
vol. 30 ,1999.
K. S. Cheng et al., Reduction of pulse-to-pulse interaction using alternative RZ formats in
40Gb/s systems, IEEE Photonics. Technology. Letters, vol. 14, No. 1, pp. 98-100 2002.
T. Franck et al., Duo binary transmitter with low intersymbol interference, IEEE photonics
technology letters , vol. 10, No. 4, : pp. 597-599, 1998.
Y. Miyamoto et al.,100GHz spaced 843Gbit/s DWDM unrepeatered transmission over 163km
using dobinary-carrier-suppressed return-to-zero format, Electronics Letters, vol. 37, No. 23, pp.
1395-1396, 2001:.
88
[41
]
[42
]
D. Breuer et al., Comparison of NRZ and RZ modulation format for 40Gb/s TDM standard-fiber
systems, IEEE photonics technology letters, vol. 9, No. 3, pp. 340-398, 1997.
Ron Hui et al., Advanced Optical Modulation Formats and The Comparison in Fiber-Optic
Systems, A Technical Report to Sprint, by Light wave Communication Systems Laboratory, The
University of Kansas, 2004.
Publications
[1
in
Engineering
and
Technology
(IJARET),Volume:5,Issue:2,Pages:37-51. [PUBLISHED].
[2
Bhumit P. Patel, Prof. Rohit B. Patel, NRZ Vs. RZ Based on Eye Closure
Penalty and
2014 Seventh
89