Import/Export 2 Africa
Fax
+27 12 6634224
Website
www.linkworld.co.za
E-mail
sales@linkworld.co.za
support@linkworld.co.za
Address
32 Kersieboom Crescent
Swartkop Ext 4
Centurion
South Africa
0046
Coiler Operation and Maintenance
Center
Operation Guide
Edition
Copyrights
The information contained herein is the property of Coiler Corporation. No part of this
document may be reproduced or transmitted in any form or by any means, electronic
or mechanical and for any purpose without the prior written permission of Coiler.
Your comments can assist us in improving our products and services. Please address
them to Coiler at any time.
Website : www.coiler.com.tw
Email : sales@coiler.com.tw
Communication between the OMC and the repeaters is ensured via a short
messaging system (SMS) through a wireless modem, or locally through a RS-232
cable. The OMC system can remotely control up to 16,000 repeaters on a network.
Coiler's OMC software is compatible with Microsoft Windows 2000 or later.
Repeater Monitor and Control: this function lets the user to monitor and
control the repeater’s main parameters. For details, please see the table below.
Alerts Message Management: this function allows the user to supervise alert
messages and send SMS messages to the maintainers.
User and Log Management: this function enables operators of the system to
check history of system logins.
Wireless GSM Modem Set (Including main unit, an antenna, power supply,
RS232 data cable, RS232/USB Cable). Coiler recommends Wavecom
FASTRACK modems. OPTIONALLY AVAILABLE FROM COILER.
GSM active SIM Card with PIN deactivated for each of the RCU units.
To start installation, run the setup.exe file and the setup wizard will guide
you through the whole installation process.
The wizard will display “Failed Registration” window. Press the OK button
and you will be prompted to register. You will be asked to input a user ID,
Key and Serial number. Please follow the steps below as this is only a one
time procedure during installation:
3. Open the text file named “Get Registration Key” file (enclosed with
the OMC software) and enter the user ID and Key in the lines
provided. Email this file to the system administrator at Coiler
Corporation at allenchou@coiler.com.tw.
4. Once the email has been received, the Serial will be emailed to
you.
5. Run the setup wizard again and input your user ID, Key and Serial
as indicated.
The laptop will be used for the local control and setup of the repeaters. To
start installation, run the setup.exe file and the setup wizard will guide you
The wizard will display “Failed Registration” window. Press the OK button
and you will be prompted to register. You will be asked to input a user ID,
Key and Serial number. Please follow the steps below as this is only a one
time procedure during installation:
3. Open the text file named “Get Registration Key” file (enclosed with
the OMC software) and enter the user ID and Key in the lines
provided. Email this file to the system administrator at Coiler
Corporation at allenchou@coiler.com.tw.
4. Once the email has been received, the Serial will be emailed to
you.
5. Run the setup wizard again and input your user ID, Key and Serial
as indicated.
2. Insert active SIM card with PIN deactivated into Wireless Modem.
Connect to
Computer’s
USB Port
Connect to DC
Power Supply
Open the OMC program and type in the user ID (admin) and password (coiler).
(Please note that this user ID and password are not the same ones used in the
software setup of the OMC). Access passwords can be changed by going into the File
menu and selecting Modify Password.
In the top toolbar select Management then System Management and finally System
Setting and you should come up to the screen shown below:
Once you have filled in the information click Save then click OK and click OK again
and then close the window.
On the main menu, press the Start Comm icon and there should be a message at the
bottom of the screen saying, “GSM Status: Ready.” If this message is not shown then
there is a problem with the RS232 or modem connection. Please try connecting the
cable and modem again so the message appears. Please also check if SIM card is
active and it does not have a PIN confirmation request active.
Repeat the previous step for the laptop computer(s). Please make sure the
information is the same as what was entered into the central computer system setup.
Please do not start communication by pressing the Start Comm icon at this point.
Before you can program any repeater on the system you must configure the system
and create a zone for the repeaters. This usually reflects the geographic placement of
the repeater(s) in the network.
In the top toolbar select Edit then New Zone. Input a new zone name in the Zone and
Parent Zone fields to reflect where you plan to place the repeaters. This function will
Select Edit and then click on New Repeater to install a new repeater. You will see the
following screen:
The information below will help you fill in the fields for the New Repeater screen:
Center Number: SIM number (with area code and +) of center modem
Once you have completed the fields in the screen click OK. Please note that under
the Edit menu you can also Modify, Delete, Find and Import a repeater. There is also a
Repeater Type option under the Edit menu. Here you can change the settings of the
repeater type and its max gain value.
Repeat the previous set to setup the repeaters on the laptop(s). Please note that the
information must be the same as what was entered on the central computer.
I. Connect the OMC laptop to the RCU using the RS232/USB cable. You may
be requested to install RS232/USB cable drivers.
Please note that if you decide not to use Coiler’s USB/RS232 adapter there is
a risk that some other adapters not recommended by Coiler will not work with
the OMC installed in your laptop.
III. Next, you will have to set the repeater parameters. Select Management then
Repeater Control and finally Control Setting. Please see the following
diagrams:
1. Select Set New Repeater ID, insert repeater ID and press Send.
2. You will hear a “bit” tone. Go to the Messages section on the main
3. Repeat steps one and two for all the parameters in the Controller
Parameter Setting. You should see Send and Receive messages each
time you set a setting.
VII. Prepare a field test by making a call on a mobile/cell phone to make sure everything
is in order.
B. Users
C. Maintainer Information:
In the main tool bar select
Management then System
Management then under the
Permission folder click on the
Maintainers icon. You can increase,
revise or delete the maintainer’s
information here.
D. Log Information:
1
(Green)
2
(Orange)
3
(Red)
Please note:
Turbo Key OFF:AGC ON
Turbo Key ON :AGC OFF
C. :
Send Short Message:
By clicking on the
Maintainer’s List, you can
view all of the maintainers’
information as shown to the
right.