The
revised table is on the following page.
January 2010
M8207E
Copyrighted material licensed to Stanford University by Thomson Scientific (www.techstreet.com), downloaded on Oct-05-2010 by Stanford University User. No further reproduction or distribution is permitted. Uncontrolled wh
ERRATA
to
ASME B47.1-2007
Gage Blanks
6-T
7-T
8-T
9-T
10-T
11-T
12-T
3.010
3.510
3.510
4.010
4.010
4.760
318312
418434
3584
2.510
3.010
2583
218212
1582
114112
8118
1634
812
714
638
512
412
334
314
258
2316
134
16
15
16
15
16
13
112
112
1716
138
1516
114
118
15
16
...
16
11
16
16
32
11
...
...
538
458
378
338
278
238
178
112
1116
...
...
...
338
21516
2716
11932
1316
32
27
16
32
11
16
32
...
32
32
32
32
32
32
3132
258
2732
134
1716
1316
16
31
32
16
16
32
19
64
32
16
16
32
16
16
16
16
16
16
32
2916
2316
11516
11116
138
118
16
11
32
15
16
16
13
16
13
16
13
32
17
32
17
32
11
32
16
16
16
16
16
32
13
32
13
32
M
164
16
16
16
16
16
32
32
16
16
N
164
No. 41
(0.0960)
No. 31
(0.1200)
No. 25
(0.1495)
No. 7
(0.2010)
No. 1
(0.2280)
17
64
(0.2656)
17
64
(0.2656)
21
64
(0.3281)
21
64
(0.3281)
21
64
(0.3281)
13
32
(0.4062)
13
32
(0.4062)
11
64
(0.1719)
7
32
(0.2187)
17
64
(0.2656)
21
64
(0.3281)
25
64
(0.3906)
29
64
(0.4531)
29
64
(0.4531)
33
64
(0.5156)
33
64
(0.5156)
33
64
(0.5156)
41
64
(0.6406)
41
64
(0.6406)
Drill Size,
R
All pitches
Pitches 12 TPI and finer except 91612
Pitches 10 TPI and finer
...
Pitches coarser than 12 TPI
Pitches coarser than 10 TPI
Max.
0.250-28
0.216-28
0.164-36
Size
Max.
0.2268 0.2290
0.375-24
0.3479 0.3503
0.625-18
0.500-20
0.500-20
0.500-20
0.5889 0.5919
0.4675 0.4701
0.4675 0.4701
0.4675 0.4701
0.5710 0.5715
0.4510 0.4515
0.4510 0.4515
0.4510 0.4515
0.3340 0.3344
32
32
32
32
32
16
16
16
16
32
Min.
Pitch Diameter
0.2150 0.2153
0.1810 0.1813
0.1370 0.1373
Min.
Ream, S
32
32
32
32
16
32
1
GENERAL NOTES:
(a) All dimensions are in inches.
(b) Thin gage blanks are to be used for all NOT GO thread ring gages. For GO thread ring gages, use thin or thick blanks as follows.
Thin Blank
Diameter, in.
Thick Blank
4-T
5-T
3-T
4 16
1 8
2-T
0.059
0.230
0.230
0.365
0.365
0.510
0.510
0.825
0.825
1.135
1.135
1.510
1.510
2.010
2.010
2.510
1-T
No. 0 to
6 (1)
Drill Size,
P
(No. or in.)
General Dimensions
Thread Ring Gages Range No. 0 to and Including 434 in.; Also Fine-Pitch Instrument Thread Ring Gages,
No. 0 to and Including No. 12 (Contd)
Decimal
Nominal
Range,
Ring
Ring
Range,
Above
Size Assembly Inclusive,
and
No.
No.
No. or in. Including
Table 32
Copyrighted material licensed to Stanford University by Thomson Scientific (www.techstreet.com), downloaded on Oct-05-2010 by Stanford University User. No further reproduction or distribution is permitted. Uncontrolled wh