High Resolution or
High Visibility Rotors.
7/16 Hex Hub
Ceramic Shaft
Heavy Duty,
Buna N O-Rings
F-1
Dimensions
Polypropylene Bodies
2.37
(60.2 mm)
.64 (16.3 mm)
VDC
VAC
Typical Applications
Protect expensive electronic
equipment from coolant ow
failure on...
.80
(20.3 mm)
2.38 (60.5 mm)
Semiconductor
Processing Equipment
Lasers Medical Equipment
X-Ray and Other High Power Tubes
Robotic Welding Equipment
Specications
Wetted Materials
Body
Rotor Pin
Rotor
Lens
O-Ring
Low Flow Adaptor
Operating Pressure, Maximum
Brass or Stainless Steel Body
Polypropylene Body
Operating Temperature,
Brass or Stainless Steel Body
Polypropylene Body
Electronics
Viscosity, Maximum
Input Power
Relay Contact Ratings (SPDT)
Current Consumption
24 VDC
115 VAC
Repeatability
Set Point Accuracy (Factory Set)
Set Point Differential
Electrical Termination
VDC
VAC
.87
(22.1 mm)
2.50
(63.5 mm)
1.06
(26.9 mm)
2
(50.8 mm)
3.94
(100 mm)
VAC
Note:
1. Optional pulsed output available with RFS. Consult factory.
1.06
(26.9 mm)
4.76
(120.9 mm)
F-2
RFS TYPE
1/2" STRAIN
RELIEF HOLE
LED INDICATOR IS
ILLUMINATED WHEN
RELAY SWITCH IS
CLOSED. AIDS FIELD
CALIBRATION
CABLE
OUTPUT
SET POINT
ADJUSTMENT
How To Order
.25
0.5 to 5.0
Polypropylene
.50
.25
.50
1.5 to 12.0
0.1 to 1.0
1.5 to 12.0
4.0 to 20.0
0.5 to 5.0
4.0 to 20.0
Brass
.75
1.00
9/16-18**
0.1 to 1.0
5.0 to 30.0
8.0 to 60.0
0.5 to 5.0
Stainless
Steel
.50
.75
1.00
1.5 to 12.0
4.0 to 20.0
5.0 to 30.0
8.0 to 60.0
Input
Power
Part
Number
24 VDC
155425
115 VAC
155876
24 VDC
155485
115 VAC
155886
24 VDC
156265
115 VAC
156266
24 VDC
156268
115 VAC
156269
24 VDC
180395
115 VAC
180396
24 VDC
181688
115 VAC
181689
24 VDC
165073
115 VAC
165074
24 VDC
165077
115 VAC
165078
24 VDC
181691
115 VAC
181692
24 VDC
181693
115 VAC
181694
Pressure Drop-Typical
Standard 12
Flow Range 9
Units
6
0
012 345
10
15
Flow Rate GPM
20
25
10
15
Low Flow
Range Units 6
0 .1 .2 .3 .4 .5 .6 .7 .8 .9 1.0
3/4
Ports
1.0 Ports
3
0
2
3
4
5
Flow Rate GPM
12
PSI
GEMS caters to OEM needs with special congurations for potable water and
enhanced chemical capabilities. Consult factory for further details.
1/2 Ports
1/4 Ports
3
0
High Flow
Units
Special Requirements:
1/2 Ports
* With use of Low Flow Adapter supplied. See Page F-8 for more information.
** Straight thread with O-ring seal.
Stock Items.
1/4
Ports
PSI
Port Size
NPT
PSI
Body
Material
Specify Part Number based on desired body material, port size and input power rating.
10
20 30
40 50
60 70
Flow Rate GPM
80 90 100 110
F-3
Panel Mounting
8 MIN
(20 CM)
Incoming
Flow
Low Flow
Adapter
Except for straight-thread versions, RotorFlow sensors connect to piping via NPT
mating thread forms.. The use of an appropriate thread sealant is necessary to assure
a leak-tight connection. Permatex No More Leaks or 2 wraps of Teon tape are
the only sealants recommended for GEMS ow sensors. Straight-thread versions
require an O-ring for sealing.
150 micron ltration is recommended. However, should foreign particles enter the
RotorFlow sensor, accumulation is easily cleared by removing the lens from the body.
The lens is removed by turning its 7/16 hex center hub 45 counter-clockwise with
a standard socket wrench. To reinstall the lens, simply reverse the process. Pressure
must be relieved from the system prior to sensor clean-out. O-rings should be
lubricated prior to re-assembly.
Part Numbers
Body
Material
O-Ring
Material
in Kit
RFA/RFO/
RFS
RFI
Plastic
Buna-N
155870
155872
Brass/SS
Viton
167364
166267
Brass/SS
Viton
157186
157187
Stock Items.
RF-2500 Sensors
Panel Mounting
Tabs
PPS Composite
with Teon or Nylon
Loaded Bushing
Long-Life
Ceramic
Rotor Pin
Hydrolytically Stable
Polypropylene, Stainless
Steel or Brass
Call 800-378-1600
F-8