# 18
Submitted to.
S i r S h a fi - u d - d i n
Lab No. 1
Lay out of the lab
Lab no. 2
Basic parts of IC Engine:
Working of the internal
combustion engine and its
main parts.
Objective:
To get familiar with IC engine , its parts and working.
Engine:
Combustion of different components that arrange in such a way
that it converts heat energy in mechanical energy.
Types of engine:
IC engine:
Combustion takes place internally
EC engine:
e.g Steam engine
Components of IC engine:
1.
Cylinder block:
Cylinder is the main body of IC engine. All other parts are assembled
into it. it is made by high grade cast iron or by aluminum alloy.
2.
Cylinder head
3.
Cylinder:
Burning of fuel occurs into it. Piston lies here and moves up & down.
It is of cylindrical shape and is fitted in cylinder block.
4.
Piston:
5.
Piston Ring:
1. Compression rings:
Forms a compact barrier against the fuel mixture not to leak it from
cylinder.
2. Oil control rings:
It lubricates the cylinder wall and provides lubrication between
piston and cylinder wall.
6.
Connecting Rod:
7.
Crank shaft:
8.
Cam shaft:
9.
Spark Plug:
Produces a spark upon high voltage, which burns up the air fuel
mixture
14. Manifold:
Means many folds, The main function of manifold is to supply the
air fuel mixture and collects the exhaust gases equally form all
cylinder. In an internal combustion engine two manifold are
used, one for intake and other for exhaust. They are usually
made by aluminum alloy.
Lab no. 3:
Demonstration of four stroke
engine:
A four-stroke engine (also known as four cycle) is an internal
combustion (IC) engine in which the piston completes four
separate strokes while turning a crankshaft. A stroke refers to
the full travel of the piston along the cylinder, in either
direction. The four separate strokes are termed:
1. Intake: This stroke of the piston begins at top dead center
(T.D.C.) and ends at bottom dead center (B.D.C.). In this
stroke the intake valve must be in the open position while
the piston pulls an air-fuel mixture into the cylinder by
producing vacuum pressure into the cylinder through its
downward motion.
2. Compression: This stroke begins at B.D.C, or just at the end
of the suction stroke, and ends at T.D.C. In this stroke the
piston compresses the air-fuel mixture in preparation for
ignition during the power stroke (below). Both the intake and
exhaust valves are closed during this stage.
3. Combustion: This is the start of the second revolution of the
four stroke cycle. At this point the crankshaft has completed
a full 360 degree revolution. While the piston is at T.D.C. (the
end of the compression stroke) the compressed air-fuel
mixture is ignited by a spark plug (in a gasoline engine) or
by heat generated by high compression (diesel engines),
forcefully returning the piston to B.D.C. This stroke produces
mechanical work from the engine to turn the crankshaft.
4.
Explanation:
What Makes 4-Cycle Overhead Valve
Engines Different?
In overhead valve (OHV) engines, the valves are positioned above
the piston. The camshaft moves the valves through a tappet,
pushrods and rocker arms. 4-cycle OHV engines provide more
efficient combustion by allowing the air-fuel mixture to spread
more evenly throughout the combustion chamber.
Lab no. 4:
Demonstration of two stroke
engine:
Objective:
To know about working of 2 stroke engine.
Theoretical background:
the inlet and exhaust are timed, It means that the inlet and
exhaust strokes are timed. Hence the names given: two stroke
engines uses two strokes, therefore a four stroke engine would
use four distinct strokes. In a four stroke engine, the order of
operation is as follows: Intake, Compression, Ignition, and
Exhaust. In a two stroke engine however, the strokes are called
the Power Stroke and the Exchange Stroke. If we think in terms
of a four stroke engine, there are two parts to the intake stroke
In a four-stroke engine, each of the four essential steps of the
power-producing cycle is given its own piston stroke:
1) Compression
2) Power
3) Exhaust
4) Intake
A two-stroke performs all the same steps, but in just two piston
strokes. The simplest two-strokes do this by using the
crankcase and the underside of the moving piston as a fresh
charge pump. Such engines carry the official name
crankcase-scavenged two-strokes.
Upward stroke:
Piston moves upwards
Inlet valve opens and air fuel mixture is drawn into the
chamber.
Exhaust and transfer valve remain closed.
At the end of this stroke compression and suction is
complete.
Downward Stroke:
Lab no. 5:
Demonstration of diesel and
petrol engine
Objective:
To know about working of diesel and petrol engine.
To know about difference between
Basic differences:
1.
2.
3.
Criteria of
comparison
Working
Cycle
Fuel used
Compression
Ratio
Petrol
Engine
Constant
volume
Otto cycle
Petrol
8:1
Diesel
Engine
Constant
pressure
Diesel cycle
Diesel
22:1
4.
Fuel supply
5.
Spark
ignition
6.
7.
8.
Initial cost
Running
Maintenance
cost
Chances of
pre-ignition
Combustion
Noise
Field of
application
Pressure
Weight
Efficiency
Energy
content
Power =
torque*RPM
Auto-ignition
temperature
CO2
emission
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Carburetors
are used
Plug is used
Less
More
Less but
frequent
More
Fuel injectors
are used
Heat of
compression
is used
More
Less
More but not
frequent
Less
Smooth
Less
Light duty
Irregular
More
Heavy duty
Less
Less
35%
34.6 MJ/litre
More
More
45%
38.6 MJ/litre
Runs at
higher RPM
246C
Runs at
higher RPM
210C
Lower than
diesel.
More than
gasoline(petr
ol). Diesel
fuel
produces
approximatel
y 13% more
CO2 gas per
gallon of fuel
burned,
compared to
gas (petrol)
20.
Viscosity
No change
21.
Dangerous
its
dangerous
due to its
volatility
engines
increase at
lower
temperature
s
Nonvolatile , so
not
dangerous
2. Compression stroke: Both the valves are closed and the piston
moves from B.D.C. to T.D.C. The charge is compressed up to a
compression ratio of 5:1 to 9:1 and pressure and temperature at
the end of compression are about 6 to 12 bar and 250 C to 300
C respectively.
3. Working, Power or Expansion stroke: When the piston
reaches T.D.C. position, or just at the end of compression stroke,
the charge is ignited by causing an electric spark between the
electrodes of a spark plug, which is located some where in the
walls of cylinder head. During combustion the chemical energy of
fuel is released and there is rise in temperature and pressure of
gases. The temperature of gases increases to about 1800 C to
2000 C and the pressure reaches 30 to 40 bar. Up till now the
volume of gases formed however remains almost constant with
both valves closed. Now the combustion products expand and
push the piston down the cylinder. The reciprocating piston
motion is converted into rotary motion of crankshaft by a
connecting rod and crank. During expansion the pressure drops
due to increase in the volume of gases and absorption of heat by
cylinder walls.
3. Exhaust stroke: Theoretically exhaust valve opens at the end of
working stroke when the piston is at B.D.C. position. But actually
exhaust valve begins to open when about 85 % of the working
stroke is completed. A pressure of 4 to 5 bar at this instant forces
about 60 % of the burnt gases into the exhaust manifold at high
speed. The remaining burnt gases are cleared off the swept
volume when the piston moves from B.D.C. to T.D.C. During this
stroke the pressure in side the cylinder is slightly above the
atmospheric value. Some of the burnt gases are however left in
the clearance space. The exhaust valve closes shortly after the
piston reaches T.D.C. The inlet valve opens slightly before the end
of exhaust stroke and the cycle repeats
coming from B.D.C. to T.D.C. forces the burnt gases into the
exhaust manifold. Some of the gases are forced out due to higher
pressure in the cylinder and the remaining gases are forced out
by the piston. Some of the burnt gases are however left inside the
clearance space. The exhaust valve closes shortly after T.D.C. The
inlet valve opens slightly before the end of exhaust and in this
way the cycle repeats.
Lab no. 6:
Demonstration of ignition
system, of an engine.
Objective:
To learn what is the ignition system and its components.
To learn how these components combine together to form a spark.
Theoretical Background:
The system which ignites the air fuel mixture to form a
spark, due to which power is produced and component of engine
runs.
Ignition Switch.
The primary circuit starts at the battery and flows to the
ignition switch. It controls the flow of electricity across the
terminals.
I.
Ignition Coil.
The primary circuit leads from the ignition switch to the
ignition coil. An ignition coil is actually a step up transformer and
electromagnet having two types of windings .
I.
II.
Primary windings
Secondary windings
that is capable of increasing battery voltage to as much as
100,000 volts, although most coils produce about 50,000-60,000
volts.
Contact breaker:
A contact breaker (or "points") is a type of electrical switch, and
the term typically refers to the switching device found in the
distributor of the ignition systems of spark-ignition internal
combustion engines. The purpose of the contact breaker is to
interrupt the current flowing in the primary circuit of the ignition
coil.
CONDENSER:
The condenser, also known as a capacitor, is wired in parallel with
the contact points and grounded through the distributor
housing. The condenser prevents arcing or burning at the
distributor contact points when the points are first open. The
condenser provides a place where current can flow until the
contact points are fully open.
Spark plug:
It receives a high voltage spark from secondary coil through rotor
and outer terminal having two electrodes
I.
II.
Control electrodes
Ground electrodes
Distributor:
As name indicates, it distributes electric current. It has two parts.
I.
II.
Distributor CAM:
Distributor rotor:
They transfer voltage from central terminal to outer terminal.
Contact points:
The contact points used on older vehicles were a simple
mechanical way of making and breaking the coil primary circuit.
It also distributes the high voltage surges to spark plug in correct
order.
The two types are:
Fixed point:
The stationary piece is grounded through the distributor contact
point mounting plate. This section does not more other than for
an initial point adjustment.
Movable point:
The second piece is the movable contact point. It is pivoted on a
steel post. A fiber spring presses the movable contact arm against
the stationary unit, causing the two contact points to touch each
other.
Lab no. 7:
Demonstration of cooling
system of an Engine:
Objective:
1. To keep the engine running at its most efficient
temperature.
2. To know about working of water cooling system.
3. To know about working of air cooling system.
Theoretical background:
During combustion process engine produces tremendous amount
of heat. That amount of heat is dissipated in different areas.
(20-25)% of heat is used in brake power
(30-35)% of heat is extracted by cooling system
Remaining amount of heat is dissipated in friction and exhaust
gases.
Thermostat:
The thermostat regulates the flow of coolant into the engine
keeping it at its optimum operating temperature. The
thermostat is closed when the engine is cold. As the engine
heats up, the thermostat opens and allows coolant from the
radiator to circulate.
It is having wax pellet , which melts and valve opens.
Water Pump:
The water pump is considered the heart of the cooling system
and is usually located on the front of the cylinder block. A hose
carries cooled coolant from the radiator to the water pump. A
belt or chain turns the water pump shaft and coolant enters the
center of the pump. The water pump has fan-like blades on an
impeller that spins, creating centrifugal force, moving the liquid
outward. Coolant is routed through the engine, cylinder heads
and intake manifold by way of water jackets. The coolant then
absorbs heat from the engine components and, once hot,
leaves the engine and enters the radiator once again to begin
the next cooling cycle.
Radiator Cap:
It is having a spring valve loaded mechanism. The radiator cap
is responsible for maintaining the proper amount of cooling
system pressure. If the amount increases above the set
pressure point, a spring-loaded valve in the cap releases extra
pressure.
Water Jacket:
These are passage inside engine which allows coolant to flow
inside engine, and further by coolant heat is extracted
Fans:
Draws the air inside the engine by passing air through radiator
which cool down the temperature of coolant.
Antifreeze
The coolant that courses through the engine and associated
plumbing must be able to withstand temperatures well below
zero without freezing. It must also be able to handle engine
temperatures in excess of 250 degrees without boiling. A tall
order for any fluid, but that is not all. The fluid must also
contain rust inhibiters and a lubricant.The coolant in today's
vehicles is a mixture of ethylene glycol (antifreeze) and water.
The recommended ratio is fifty-fifty. In other words, one part
antifreeze and one part water. This is the minimum
recommended for use in automobile engines. Less antifreeze
and the boiling point would be too low. In certain climates
where the temperatures can go well below zero, it is
permissible to have as much as 75% antifreeze and 25% water,
but no more than that. Pure antifreeze will not work properly
and can cause a boil over.
Lab no. 8:
Demonstration of lubrication
system
Objectives
Explain the purpose of the lubrication system.
Describe oil ratings
Identify the main components of the lubrication
system
System Components
Components:
Oil pressure switch
Lifter/buckets
Piston jets
Sump/pan
Pickup tube
Oil pump
Oil filter
Viscosity
If the oil is too thin(has very low viscosity) it will be forcedout
from between the moving parts, resulting in rapid wear.
If the oil is too thick(has very high viscosity)it will flow veryslowly
to engine parts, especially when the engine and the oilare cold,
resulting in rapid wear.
Viscosity Indexis the measure of how much the viscosity ofan oil
changes with temperature. (20 W)Viscosity number is set by
SAE (Society of Automotive Engineers)
Oil Pan Stores the oil and helps in cooling the oilPan gasket splits
if over tightened.
Oil Filter filters the oilSome particles are too small for the
filter
Element(paperin the filter) to trap.
Lab no. 9:
BRAKING SYSTEM OF A CAR
OBJECTIVE:
The objective of this lab is to:
Understand the working principle of braking system.
Analyze how force is transmitted to the wheels.
THEROROTICAL BACKGROUND:
Two type of braking systems are used:
the front ones only. Under heavy braking, so much weight may
come off the rear wheels that they lock, possibly causing a
dangerous skid. For this reason, the rear brakes are
deliberately made less powerful than the front. Most cars now
also have a load-sensitive pressure-limiting valve. It closes
when heavy braking raises hydraulic pressure to a level that
might cause the rear brakes to lock, and prevents any further
movement of fluid to them. Advanced cars may even have
complex anti-lock systems that sense in various ways how the
car is decelerating and whether any wheels are locking. Such
systems apply and release the brakes in rapid succession to
stop them locking.
WORKING PRINCIPLE:
Working principle of a hydraulic braking system is pascal law that
is applied pressure is transmitted into all directions uniformly.
TYPES OF BRAKE:
DISK BRAKE :
A disc brake has a disc that turns with the wheel. The disc is
straddled by a caliper, in which there are small hydraulic
pistons worked by pressure from the master cylinder. The
pistons press on friction pads that clamp against the disc from
each side to slow or stop it. The pads are shaped to cover a
broad sector of the disc. There may be more than a single pair
of pistons, especially in dual-circuit brakes. The pistons move
only a tiny distance to apply the brakes, and the pads barely
clear the disc when the brakes are released. They have no
return springs. Rubber sealing rings round the pistons are
designed to let the pistons slip forward gradually as the pads
wear down, so that the tiny gap remains constant and the
brakes do not need adjustment. Many later cars have wear
sensors leads embedded in the pads. When the pads are nearly
worn out, the leads are exposed and short-circuited by the
DRUM BRAKE:
A drum brake has a hollow drum that turns with the wheel. Its
open back is covered by a stationary back plate on which there
are two curved shoes carrying friction linings. The shoes are
forced outwards by hydraulic pressure moving pistons in the
brake's wheel cylinders, so pressing the linings against the
inside of the drum to slow or stop it. With the brakes on, the
shoes are forced against the drums by their piston. Each brake
shoe has a pivot at one end and a piston at the other. A leading
shoe has the piston at the leading edge relative to the direction
in which the drum turns. The rotation of the drum tends to pull
the leading shoe firmly against it when it makes contact,
improving the braking effect. Some drums have twin leading
shoes, each with its own hydraulic cylinder; others have one
leading and one trailing shoe - with the pivot at the front. This
design allows the two shoes to be forced apart from each other
by a single cylinder with a piston in each end. It is simpler but
less powerful than the two-leading-shoe system, and is usually
restricted to rear brakes. In either type, return springs pull the
shoes back a short way when the brakes are released. Shoe
travel is kept as short as possible by an adjuster. Older systems
have manual adjusters that need to be turned from time to
time as the friction linings wear. Later brakes have automatic
adjustment by means of a ratchet. Drum brakes may fade if
they are applied repeatedly within a short time - they heat up
and lose their efficiency until they cool down again. Discs, with
their more open construction, are much less prone to fading.
Lab no 10:
FUEL SYSTEM OF AN IC ENGINE
OBJECTIVE:
The objective of this lab is to understand the fuel system of an ic
engine and to
know in what ratio air and fuel are
combusted.
THEROTICAL BACKGROUND:
In a IC system fuel and air are mixed together and are combusted
to get the power but the question is in what ratio air and fuel
are mixed together. So usually the ratio is 14:1 where 14 part
of air mixed with 1 part of fuel.
Fuel tank:
Basically a holding tank for your fuel. When you fill up at a gas
station the gas travels down the filler tube and into the tank. In
the tank there is a sending unit which tells the gas gauge how
much gas is in the tank. In recent years the gas tank has
become a little more complicated, as it now often houses the
fuel pump and has more emissions controls to prevent vapors
leaking into the air.
Fuel pump:
On newer cars the fuel pump is usually installed in the fuel
tank. Older cars have the fuel pump attached to the engine or
on the frame rail between the tank and the engine. If the pump
is in the tank or on the frame rail then it is electric and is run by
your cars battery. Fuel pumps mounted to the engine use the
motion of the engine to pump the fuel, most often being driven
by the camshaft, but sometimes the crankshaft.
Fuel filter:
Clean fuel is critical to engine life and performance. Fuel
injectors and carburetors have tiny openings which clog easily
so filtering the fuel is a necessity. Filters can be before or after
the fuel pump, sometimes both. They are most often made
from a paper element, but can be stainless steel or synthetic
material and are designed to be disposable in most cases.
Some performance fuel filters will have a washable mesh,
which eliminated the need for replacement.
Fuel injectors:
Most domestic cars after 1986 and earlier foreign cars came
from the factory with fuel injection. Instead of a carburetor to
mix the fuel and air, a computer controls when the fuel
injectors open to let fuel into the engine. This has resulted in
lower emissions and better fuel economy. The fuel injector is
basically a tiny electric valve which opens and closes with an
electric signal. In the picture below you can see the injectors
towards the outer part of the intake. By injecting the fuel close
to the cylinder head the fuel stays atomized ( in tiny particles )
so it will burn better when ignited by the spark plug.
Carburetors:
A carburetor take the fuel and mixes it with air without
computer intervention. While simple in operation, they tend to
need frequent tuning and rebuilding. This is why most new cars
have done away with carburetors in favor of fuel injection.
Throttle Valve:
It is a butterfly type valve use to regulate the flow of fluid.
Idle System
The carburetor idle system provides the air-fuel mixture at
speeds below approximately 800rpm or 20 mph(0-40) When
the engine is idling, the throttle is almost closed Air flow
through the air horn is restricted to produce enough vacuum in
the venture. Since venture vacuum is too low to pull fuel from
the main discharge tube, the high intake manifold vacuum
BELOW the throttle plate and the idle circuit are used to feed
fuel into the air horn. The fundamental parts of the carburetor
idle system include a section of the main discharge tube, a lowspeed jet, an idle air bleed, a bypass, a idle passage, an
economizer, an idle screw port, and an idle mixture screw.
Accelerating circuit:
The purpose of the accelerator pump system is to provide
the momentary additional fuel needed to sustain
smooth engine operation under a rapid acceleration
This extra fuel is instantly needed due to the fact that
as the throttle is suddenly opened wide, the air fl ow
and manifold vacuum being light change almost
instantaneously while the heavier fuel tends to lag
behind. Without this added fuel from the pump circuit
being
forced into
the
carburetor
at the
instant of
throttle
opening, a
lag or
engine
hesitation
would most
certainly
result.
THEOROTICAL BACKGROUND:
Transmission system in a car helps to transmit mechanical
power from the car engine to give kinetic energy to the wheels.
It is an interconnected system of gears, shafts, and other
electrical gadgets that form a bridge to transfer power and
energy from the engine to the wheels. The complete set up of
the system helps to maintain the cruising speed of the car
without any disturbance to the cars performance. The oldest
variant of the transmission system in India is the manual
transmission that has undergone various modifications and
alterations to form the present day automatic transmission.
A transmission or gearbox provides speed and torque
conversions from a rotating power source to another device
using gear ratios. The transmission reduces the higher engine
speed to the slower wheel speed, increasing torque in the
process. A transmission will have multiple gear ratios (or
simply "gears"), with the ability to switch between them as
speed varies. This switching may be done manually (by the
operator), or automatically. Directional (forward and reverse)
control may also be provided.
COMPONENTS OF A TRANSMISSION
SYSTEM:
Universal Joints:
Universal joint is also known as cardan joint and U joint. This joint
is the point of connection in a stiff rod which enables the rod to
turn in any desired direction in auto transmission system. In
other words universal joint is a joining link between two shafts
that are in a changing position. These automotive transmission
parts are one of the earliest form of flexible couplings that have
two shaft yokes located at 90 degrees angle to each other and
a four point cross that fasten the yokes.
Transmission Axles:
Transmission axles are the shafts usually rods or bars, which are
used for providing support to differential shafts and wheels in
order to actuate a vehicle. These transmission parts consists of
spline at one end and flange at the other end. Both of these
components are used for holding tightly the wheel studs. More
precisely, transmission axle is the metal based shaft to which
wheels, brakes and other automotive suspension parts are
connected.
Output Shaft:
Differential:
Gear Shifters:
Clutch:
GEAR RATIO:
The Gear Ratio is defined as the input speed relative to the output
speed. It is typically written as: Gear Ratio = win : wout.
IST GEAR 2.5:1
2ND GEAR
1.88:1
3RD GEAR
1.46:1
4TH GEAR1:1
REVERSE GEAR2.59:1