RENCANA PELAKSANAAN
PEMBELAJARAN
(ISO 9001:2000,klausul 7.5)
No. Dokumen
Revisi ke
Tgl. berlaku
Halaman
Nama file
F 22/WKS1/
0
30 Juli 2007
1/7
RPP/KTSP
Subject
: English
Class/ Semester
: XII /3
Meeting
Time Allocation
: 2 x 40 minutes
Standard Competency
Basic Competency
Indicators
or
equipments
(consists
of;
goal,
the
- The teacher asks the students to make groups which consists of 5 members and asks
them to rearrange some jumbled sentences into a correct text
- The teacher asks some groups to perform in front of the class
c. Confirmation (5 minutes)
- Teacher discusses students works and gives revisions toward the mistakes done by
the students
- Teacher repeats once again about the nature of how to use manual tools
- Teacher asks the students whether theres any misunderstanding experienced by the
students about the teachers explanation
Post activities (10 minutes)
- Teacher asks the students to summarize the topic of the day by leading them with
some questions
- Teacher parts the students and gives them homework
V. Teaching Aids
1. Texts (enclosed)
2. Board marker
3. Hand out (English for SMK grade XI Smt 3 and A Practical English Grammar fourth
edition)
4. Written material given by the teacher
5. Some mechanical equipments
VI. Assessment Technique
Point to be assessed
In this meeting the teacher will give score for the students performance in front of the
class. Students will perform the result of re-arrangement of certain texts by reading it in
chain. The score really depends on the rubric below:
Rubric
There are five steps that should be arranged by the students. Each correct step will be
scored two. The rubric will be stated below;
Number of Correct Answer in the
Score
Arrangement
5
4
3
2
1
0
10
8
6
4
2
0
The score will be for all the members of the group. The highest score will be 10 and the
lowest one will be 0.
Additional Rubric
This additional rubric will be used in a condition in which a teacher wants to assess the
answers of the questions given about the text. There are 10 questions in part I and there
are another 10 questions in part II. Each correct answer will be scored 1 for all parts.
Then, the score will be added and be divided into 2. The highest score will be 10 and the
lowest one will be 0.
Enclosures
HOW TO CHANGE THE OIL IN YOUR CAR
There are many ways that you can do in order to make your car running well. One of
them is changing the cars engine oil and filter frequently. The changing process can be done
when there is contamination done by other chemicals unsure. It can also be done depends on
the driving habits of the owner, it can be every 3 months or 3000 miles or can be as long as
24 months or 20.000 miles. Below are the easy steps in changing your cars oil.
1. First of all, prepare all the equipments and supplies (e.g. plug, filter, socket, wrench,
ratchet, grip, oil pan, etc) under your car in order to ease you to gain them. Be careful
with the hot engine!
2.
Open the hood of the car and also the oil filler cap on the top of the engine in order to
ease you to drain the old oil. Then, put the drain plug on the oil pan and place it at the
back of the car engine to catch the oil runoff.
3. The next step is using the socket or wrench to loosen the plug counter. Sometimes, if
the bolt is tight, you can use more leverage like a pipe segment on your ratchet
handle. Be careful not to drop the plug into the oil, because it will be a hard job to
find the plug in the black stuff. If you drop it in the pan, it can be found with a magnet
which is at the end of an expandable rod.
4. The fourth step is replacing the filter. Put off the old filter and then install a new filter
in a good position. There are many notes that you should remember, such as;
a. You have to make sure that the rubber gasket ring comes off with the filler. It
is because when you leave it inside the new filter will not close rightly and
will leak.
b. Dip the tip of your finger in the new oil and smear it on the gasket ring of the
new filter after installing it.
5. Replace the drain plug on the oil pan. Don't forget to install a replacement gasket or
washer. Start threading it with your fingers and it should be snug,
6. This would be a good time to wipe any debris or buildup off the surface where the
gasket will seat. One thing that should be noticed about it is that screw on the new
filter but be careful with the threads. Then make sure also to replace all of them
without any leak. The tight of the screw will be depend on the how it is needed.
7. The next step is you should add new oil to the car at the fill hole. The amount you
need is in the owner's manual, usually listed under "capacities". It commonly depends
on the cars capacities, it can be 3.5 4 litres
8. Replace the fill cap, check around for tools and close the hood.
9. Start the engine for a minute, watching to be sure the oil pressure light goes off after
start-up. It has a purpose on checking the tight of the filler in order not to cause leak.
Key Answer
1.
2.
When you leave the gasket ring inside the new filter will not close rightly and
will leak.
3.
The next step is using the socket or wrench to loosen the plug counter.
Sometimes, if the bolt is tight, you can use more leverage like a pipe segment
on your ratchet handle
4.
It is based on the manual book or based on the capacity of the car (commonly
3.5-4 litres
5.
6.
The fourth step is replacing the filter. Put off the old filter and then install a
new filter in a good position.
7.
We can use magnet which is put at the end of the expandable rod and can also
use funnel with screening in it
8.
It depends on the driving habit of the owner, can be every 3000 miles or
20.000 miles. It can also be done when the oil break down or contaminated
9.
Socket or wrench which has been added to a pipe in order to ease us to loosen
it
10. Close the hood of the car and check whether there is any leak or not and also
checks for the oil pressure
Part II. Please find the English terms for the words below.
1. Oli: .
6. Kunci Inggris:.
2. Saringan:..
7. Mengendurkan:.
3. Peralatan:..
8. Kebocoran:..
4. Mesin:.
9. Kap mobil:.
5. Baut:..
Key Answer
1. Oil
6. Wrench
2. Filter
7. Loosen
3. Equipment
8. Leak
4. Engine
9. Hood
5. Bolt
The second text that will be arranged in inappropriate order which will become a group
assignment for the students.
How to Change Your Cars Tyre
1. The first step in changing the cars tyre is prepare all the equipments that we need like
jack, wrench, a new tyre
2. Then, use the wrench to loosen the four tyre moors to the left direction but the tyre
will not be opened yet
3. The next step is jacks up the tyre in order to make the position of the tyre higher and
ease us to change it
4. After jacking the tyre up until the right position, we can continue to loosen the bolts
and the moors and put off the old tyre
5. Finally, install a new tyre and start threading the bolts and the moors but do it in
opposite position until it is tightened well
Mengetahui,
Guru Pamong
Singaraja, 3 Oktober2009
Mahasiswa Prakerin
Yulistini, S.Pd
NIP. 19650708 198902 2 002
Dosen Pembimbing