www.NOV.com/GrantPrideco
Pipe Body OD
Pipe Body Wall Thickness
Pipe Body Grade
Drill Pipe Length
Connection
Tool Joint OD
Tool Joint ID
Pin Tong
Box Tong
(in)
(in)
(in)
(in)
(in)
(in)
80 % Inspection Class
Nominal Weight Designation
25.60
(ft) 31.9
Drill Pipe Approximate Length
(in) 3/32 Raised
SmoothEdge Height
(psi) 120,000
Tool Joint SMYS
Upset Type
IEU
(in) 5.125
Max Upset OD (DTE)
Friction Factor
1.0
5.000
0.500
S-135
Range2
XT50
6.625
3.750
10
15
Drill-Pipe Length
Best Estimates
(without Coating)
80 % Inspection Class
Applied Make-up
Torque
Max Tension
Operational
Torque (ft-lbs)
(lbs)
(ft-lbs)
Maximum MUT
46,100
Minimum MUT
38,600
Tension Only
Combined Loading
Tension Only
Combined Loading
0
37,900
746,400
637,800
0
29,900
746,400
681,100
Fluid Displacement
Fluid Displacement
Fluid Capacity
Fluid Capacity
Drift Size
29.32
0.45
(Bbls/ft) 0.0107
(gal/ft) 0.63
(Bbls/ft) 0.0150
(in) 3.625
XT50
6.625
Applied Make-up
Tension at Shoulder
Torque
Separation
(ft-lbs)
46,100
38,600
(ft-lbs)
(lbs)
(lbs)
Tensile Limited
1,066,100
SmoothEdge Height
(in)
(lbs)
3/32 Raised
6.812
1,658,000
28.27
0.43
0.0103
0.65
0.0154
(lbs/ft)
0.62
0.0149
OD X
(in)
3.750
Tension at Connection
Yield
(lbs)
ID
(in)
120,000
(psi)
876,500
1,078,000
(in)
(in)
6.406
6.066
6.066
76,900
1,078,000
(least accurate)
(gal/ft)
Nominal
(with Coating)
Connection Performance
Maximum Make-up Torque
Minimum Make-up Torque
Range2
(in)
6.625
1,440,200
6.066
826,700
Nominal
Assumed Slip Length
Transverse Load Factor (K)
(lbs)
(in)
667,800
(ft-lbs)
(ft-lbs)
(psi)
(psi)
(in)
(in)
(in)
(in^2)
(in^2)
(in^2)
(in^3)
(in^3)
5 (in) OD
80 % Inspection Class
529,900
(lbs)
S-135 )
Note: Slip Crushing: Slip crushing load is calculated with the Spiri-Reinhold equation from Why Does Drill Pipe
Fail in the Slip Area World Oil, 1959 for the slip length and transverse load factor shown and is for reference
only. Slip crushing is dependent on the slip design and condition, coefficient of friction, loading conditions, time in
slips, drill pipe OD and wall variation, and other factors. Consult with the slip manufacturer for additional
information.
16.5
4.2
Nominal
Pipe Tensile Strength
Pipe Torsional Strength
TJ/PipeBody Torsional Ratio
80% Pipe Torsional Strength
Burst
Collapse
Pipe OD
Wall Thickness
Nominal Pipe ID
Cross Sectional Area of Pipe Body
Cross Sectional Area of OD
Cross Sectional Area of ID
Section Modulus
Polar Section Modulus
(in)
Note: Elevator capacity based on assumed Elevator Bore, no wear factor, and contact stress of 110,100psi.
Note: A raised elevator OD increases elevator capacity without affecting make-up torque.
5.219
6.318
1,096,600
6.812
954,300
94,100
0.82
75,300
23,625
24,300
5.000
0.500
4.000
7.069
19.635
12.566
7.245
14.491
5 (in) OD
80 % Inspection Class
746,400
73,000
1.05
58,400
21,600
20,510
4.800
0.400
4.000
5.529
18.096
12.566
5.621
11.243
S-135 )
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully
responsible for the accuracy and suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied
warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear
conditions (remaining body wall) is for information only and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance
ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to
the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.NOV.com/GrantPrideco/CustomerFeedback
XT50
80 % Inspection Class
Tool Joint OD
(in)
6.625
Tool Joint ID
Pipe Body OD
(in)
(in)
0
2,000
4,000
6,000
8,000
10,000
12,000
14,000
16,000
18,000
20,000
21,900
23,900
25,900
27,900
29,900
31,900
33,900
35,900
37,900
(lbs)
746,400
746,200
745,300
743,900
741,900
739,400
736,300
732,600
728,300
723,400
717,900
712,000
705,300
697,900
689,700
680,900
671,400
661,000
649,900
637,800
S-135
(ft-lbs)
Connection Max
Pipe Body
Max Tension Tension
(lbs)
3.750
Operationa Assembly
l Torque
Max Tension
(ft-lbs)
(lbs)
Pipe Body
Max Tension
(lbs)
(lbs)
(ft-lbs)
Connection
Max Tension
(lbs)
746,400
746,400
1,066,100
746,400
876,500
746,200
876,500
1,600
746,300
746,300
1,066,100
876,500
3,100
745,800
745,800
1,066,100
1,066,100
745,300
743,900
876,500
4,700
744,900
744,900
741,900
876,500
6,300
743,700
743,700
1,066,100
739,400
876,500
7,900
742,100
742,100
1,066,100
736,300
876,500
9,400
740,200
740,200
1,066,100
876,500
11,000
737,900
737,900
1,066,100
876,500
12,600
735,200
735,200
1,066,100
876,500
14,100
732,400
732,400
1,066,100
1,066,100
732,600
728,300
723,400
717,900
876,500
15,700
729,000
729,000
712,000
876,500
17,300
725,200
725,200
1,066,100
705,300
876,500
18,900
721,000
721,000
1,066,100
697,900
876,500
20,400
716,700
716,700
1,066,100
876,500
22,000
711,700
711,700
1,066,100
876,500
23,600
706,300
706,300
1,066,100
700,900
700,900
1,066,100
1,066,100
689,700
680,900
671,400
25,100
876,500
661,000
876,500
26,700
694,700
694,700
649,900
876,500
28,300
688,000
688,000
1,066,100
637,800
876,500
29,900
681,100
681,100
1,066,100
Connection
Make-up Torque Range
Make-up Torque
(ft-lbs)
Min MUT
Max MUT
38,600
39,400
40,300
41,100
41,900
42,800
43,600
44,400
45,300
46,100
Connection Max
Tension
(lbs)
1,066,100
1,067,400
1,041,800
1,019,000
996,200
970,600
947,800
925,000
899,300
876,500
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
02-03-2014
XT50
Tool Joint OD
Connection
Wear
Tool
Joint OD
New OD
(in)
6.625
6.574
6.523
6.473
6.422
6.371
6.32
6.269
6.218
6.168
6.117
6.066
Worn OD
(in)
6.625
Tool Joint ID
(in)
3.750
Connection Max
Tension
Connection
Torsional
Strength (ft-lbs)
Max
MUT
76,900
76,900
76,900
76,900
76,900
75,000
72,300
69,600
67,000
64,400
61,800
59,300
46,100
46,100
46,100
46,100
46,100
45,000
43,400
41,800
40,200
38,600
37,100
35,600
(ft-lbs)
Connection Max
Tension
Min MUT
(lbs)
(lbs)
(ft-lbs)
876,500
871,700
866,800
861,700
856,300
880,200
916,800
952,800
988,000
1,022,600
1,036,000
995,600
38,400
1,060,600
38,400
1,066,300
38,400
1,072,300
38,400
1,077,400
38,400
1,070,700
37,500
1,067,900
36,100
1,036,500
34,800
1,007,700
33,500
978,900
32,200
949,600
30,900
905,100
29,600
827,800
Pipe Body
Combined Loading Table (Torque-Tension)
Pipe Body
Pipe Body OD
80 % Inspection Class
(in)
S-135
6,600
13,300
19,900
26,500
33,200
39,800
46,400
53,100
59,700
66,300
72,900
743,400
733,900
718,200
695,500
664,700
625,700
576,100
512,100
429,300
312,000
34,800
(ft-lbs)
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
02-03-2014