ITCSN
Heat Shrinkable
Cable Sleeves
Electrical Products Division
1 Product description
2 Applications
Product Features:
Fast and easy installation
Thick walls to resist puncture and abrasion
damage
Complete environmental protection
Versatile, a minimum number of sizes
cover the entire of application.
Shrink ratios as high as 4:1
Resists acids and alkalies
Bonds to a wide variety of substrates
Reliable and proven
U.V. resistant
ITCSN Selection Guide
Prod. No
ITCSN 0400
ITCSN 0800
ITCSN 1100
ITCSN 1500
ITCSN 200 0
ITCSN 3000
Conductor
sizes
(AWG or
kcmil)
12-6
8-1/0
2-4/0
3/0-400
250-750
600-1250
Maximum
Connector
O.D.
(inches)
0.350
0.650
0.875
1.19
1.60
2.25
Minimum
Cable O.D.
(inches)
0.17
0.24
0.40
0.60
0.75
1.20
3
DATA:
Properties.
Physical
and
Electrical
Wall
(inches)
0.80
0.110
.120
0.170
1.70
.170
Minimum Seal
Length Each
Slide (inches)
1.50
1.50
1.50
2.00
2.00
2.00
NOTE 1: All sleeves are lined with adhesive/sealant EXCEPT 25 foot lengths.
NOTE 2: 25 foot lengths and ITCSN 3000 are not U.L listed.
NOTE 3: Certain long barrel connectors may require moving up to the next available tube length for proper seal.
Lengths
(inches, feet)
6, 48, 25
6,9,12,48,25
6,9,12,48,25
9,12,48,25
9,12,48,25
12,48
375%
5 Performance Tests
No cracking
Typical Value*
450v/mil
(17.7MV/m)
14
1x10
ohm cm
UL 486D
ITCSN Cable Sleeves were subjected to the
requirements of UL 486D and passed all test
sequences. ITCSN Cables Sleeves are listed
per UL 486D.
Chemical Resistance
Samples of sleeving were immersed in the
following fluids for 24 hours at room
temperature and physical and electrical
characteristic were measured:
Dielectric
Tensile
Fluid
Strength
Strength
(volts/mil)
Hydraulic
2040psi
829@ 35mils
Fluid (Mil-H- (14MPa)
(32.6 MV/m)
5606)
Lube
Oil 2320 psi
|697
@
(Mil-L-7808) (16Mpa)
33mils (27.4
MV/m)
5%
Salt 2310psi
443 @ 35Mils
Solution
(16Mpa)
(17.4MV/m)
Longitudinal Shrinkage
Three 9-inch samples of ITCSN 1500 were
freely recovered in a convection air oven at 175
degrees C for 2 minutes. The longitudinal
shrinkage is computed as follows:
L1 = Original length
L2 = Length after unrestricted Recovery
% change = L2 L1 x 100%
L1
The average longitudinal shrinkage is 3%
a.
b.
c.
d.
e.
f.
Concentricity
Three samples of ITCSN 1500 were measured
for their minimum and maximum wall thickness
in the expanded state. The concentricity is
computed by dividing the maximum wall into
the minimum wall. The concentricity is 84%
7 Maintenance
6 Installation Techniques
8 Availability
Important Notice
All statements, technical information and recommendations related to the Seller's products are based on information
believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user
should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in
connection with such use.
Any statements or recommendations of the Seller which are not contained in the Seller's current publications shall have no
force or effect unless contained in an agreement signed by an authorized officer of the Seller. The statements contained
herein are made in lieu of all
warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose which warranties are hereby expressly disclaimed.
SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING
BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF
ANY OF THE SELLER'S PRODUCTS THAT WERE DEFECTIVE.
3M Per S.A.
Divisin de Productos Elctricos
Canaval y Moreyra 641
San Isidro, Lima 27 Per
Atencin al consumidor:
Telfono: 225-5252
Fax: 224-3171
e-mail: 3mperu@mmm.com