(English-Inch)
Table of Contents
Selection Procedures
1 to 10
11 to 70
Dimensional Information
71 to 84
Technical Information
85 to 110
Installation / Maintenance
111 to 114
115 to 118
119 to 127
128
Quick Reference
129
Note: In accordance with our policy to constantly improve products, the specifications in this catalog are subject to change without notice.
tocR2.p65
1
Black
7/19/2002, 10:00 AM
Accessories
Fans and shrouds furnished to maximize lubricant life and reducer performance.
introR2.p65
1
Black
7/19/2002, 10:47 AM
Planetgear reducers assure you extended reducer service-life even in the worst environments.
introR2.p65
2
Black
7/19/2002, 10:48 AM
SELECTION PROCEDURES
General Selection Information
INTRODUCTION
Before a reducer can be selected for any application, the equivalent
output torque or horsepower must be computed by multiplying the actual or specified torque or horsepower by the service factor (S.F.) for the
particular load classification for which the unit is to be used. It is necessary that the unit selected have a capacity equal to or in excess of the
equivalent output torque (lb-in) or horsepower.
Reducers can be selected by Service Factor or Load Classification. Both
Service Factors and Load Classifications are a means of classifying different equipment and applications into a uniform guideline useful for
reducer selection. Due to variations in application, service factors are
used to adjust equipment ratings to accommodate differing load conditions. Applications involving unusual or severe loading should be carefully reviewed before a service factor is applied (consult factory). Care
must be taken by the customer to isolate the reducer from unplanned
transient loads or vibrating conditions.
For unusual application requirements such as those listed below, consult the factory for application assistance.
Operating Temperature
It is important the maximum oil temperature not exceed 200F (93C). If
a continuous ambient temperature of 115F (46C) or higher exists, please
contact the factory. Thermal limitations may exist for some units with
low ratios. Heat exchangers are available for these applications that exceed the thermal capacity of reducers with fans and shrouds.
Thermal Capacity
Heat exchangers are available for those applications that are thermally
limited, contact factory.
Moment of Inertia
The moment of inertia values are listed in Table 17, page 110.
Lubrication
Planetgear reducers are shipped without oil and must be filled to the specified oil level before start-up. Lubrication instructions can be found on the
reducer nameplate, including required frequency of oil changes. Additional information on lubrication and oil capacities are listed in the Owners Manual.
Multi-Speed Selections
Reducers that will be operated at a variety of input speeds must be selected for the speed that yields the highest output torque requirement.
Backstops
Reverse rotation is prevented through the use of Planetgear backstops on
all reducer series. The ratchet mechanism engages at any frequency for
any time span, thus providing indexing, or positioning capabilities. The
pawls disengage by centrifugal force assuring quiet operation.
Our internally mounted backstops operate in conventional gear oil.
Available as stocked accessories, they are easily installed or reversed in
the field without removal of gearing. Conversion of our standard Mercury
and Mars models requires a complete backstop input endbell assembly.
When ordering a Planetgear reducer with a backstop, indicate the reducer
rotation as clockwise or counter-clockwise when looking towards the reducer from the low speed end. Note: consult factory if using a backstop
in an application that has an input speed of 400 RPM or less.
selectR2.p65
2
Black
7/19/2002, 10:50 AM
SELECTION PROCEDURES
Motorized Selection (Scoop Mount and C-face)
Three classes designated by Roman Numerals I, II and III were established by NEMA to relate the package or "Drive" to a large variety of
applications. These applications were classified by load factors and hours
per day of use. A service classification table using this nomenclature for
typical applications is located on pages 3 & 4. Reducer selections can
be made based on applying these service classifications to specific motor ratings and speeds.
Planetgear scoop mounted motor reducers are available for all reducer
series with capacities ranging from 1 horsepower (143T) to 250 horsepower (447T). These may be a face mounted or common base type
configuration depending upon the motor size. Planetgear can furnish
motors or mount those furnished by others.
Rexnord Omega couplings are standard on the high speed shaft of scoop
mounted reducers. Selections for the Omega coupling can be found in
Table 7 on page 98. A wide choice of accessories including backstops,
slidebases, and coupling guards are also available.
Planetgear C-face mounted motor reducers are available for Mercury
through Polaris, and Neptune and Orion quadruple and quintuple series. Horsepower capacities range from 1/2 horsepower (56C) to 30
horsepower (286TC). Planetgear can furnish motors or mount those
furnished by others. Reference Figure 1, page 114 for sectional view of
C-face input.
A drive for a uniformly fed chain conveyor operating 16 hours per day is
powered by a 10 hp, 1750 rpm (215T frame) motor. Desired reducer
output speed is 41 rpm. A roller chain drive having a 160B17 roller
chain sprocket (10.844 inches Pitch Diameter) is mounted so that the
centerline of the load is 2 1/2 inches from the reducer seal cage.
Read the series name under the desired motor horsepower and opposite
the approximate output speed required. The number following the reducer name in the selection table is the output capacity in (x1000) poundinches of torque.
SOLUTION:
Note: If ambient temperature exceeds 84F (29C), see Step 6 of Nonmotorized selection procedure to determine reducer thermal rating.
Step 3 Check for Overhung Load
Follow the overhung load procedure on page 9 to confirm the selection
when radial loads exist on the output shaft. For units that have a thrust
load applied, contact factory with radial and thrust load information.
Step 4 Check the Dimensions
Refer to the dimensional drawings on pages 77 to 82 for feet mounted
motors, and pages 83 to 84 for C-face reducers. Confirm the spacial
requirements of the selected reducer.
Step 5 Omega Coupling Selection (scoop mount reducers only)
Refer to page 98 for selection information based on reducer series and
load classification.
Note: Scoop mount reducers include face scoops and baseplates.
Step 6 Order the Planetgear Reducer
Refer to page 10 for information required when ordering reducers.
REQUIRED:
selectR2.p65
3
Black
7/19/2002, 10:50 AM
SELECTION PROCEDURES
Service Class Selections
TABLE 1 - SERVICE CLASSES
SERVICE
10
24
HRS/
HRS/
DAY
DAY
SERVICE
10
24
HRS/
HRS/
DAY
DAY
II
II
II
II
I
II
APPLICAT ION
APPLICAT ION
APPLICAT ION
AGITATORS
Clay Working Machinery
FANS
Pure Liquids
I
II
Pug Mills
Centrifugal
Liquids & Solids
II
II
COLLECTORS (Sewage)
Cooling Towers
Liquids - Variable Density
II
II
Forced Draft
APRON CONVEY ORS
COMPRESSORS
Induced Draft
Uniformly Loaded or Fed
I
II
Centrifugal
I
II
Large (Mine, etc.)
Heavy Duty
II
II
Lobe
II
II
Large (Industrial)
APRON FEEDERS
II
II
Reciprocating
Light (Small Diameter)
ASSEMBLY CONVEY ORS
Multi-Cylinder
II
II
FEEDERS
Uniformly Loaded or Fed
I
II
Single Cylinder
III
III
Apron, Belt
Heavy Duty
II
II
CONCRETE MIXERS
Disc
BALL MILLS
**
**
Continuous
II
II
Reciprocating
BARGE HAUL PULLERS
III
III
Intermittent
II
III
Screw
BARKING
CONVEY ORS - Uniformly
FLIGHT
Drums (coupling connected)
III
Loaded or Fed: Apron,
Conveyors, Uniform
Mechanical
III
Assembly, Belt, Bucket, Chain
Conveyors, Heavy
BAR SCREENS (Sewage)
I
II
Flight, Oven, Screw
I
II
FOOD INDUSTRY
BATCHERS (Textile)
II
II
CONVEY OR - Heavy Duty
Beet Slicers
BELT CONVEY ORS
Not Uniformly Fed: Apron,
Bottling, Can Filling Mach
Uniformly Loaded or Fed
I
II
Assembly, Belt, Bucket, Chain
Cereal Cookers
Heavy Duty
II
II
Flight, Oven, Screw
II
II
Dough Mixers, Meat Grinders
BELT FEEDERS
II
II
CONVEY OR - Severe Duty
GENERATORS (Not Welding)
BENDING ROLLS (Machine)
II
II
Live Roll
*
*
GRAVITY DISCHARGE
BLOWERS
Reciprocating, Shaker
III
III
ELEVATORS
Centrifugal
I
II
COOKERS (Brewing & Distilling)
HAMMER MILLS
Lobe
II
II
(Food)
I
II
HOISTS
Vane
I
II
COOLING TOWER FANS
*
*
Heavy Duty
BOTTLING MACHINERY
I
II
CRANES
Medium Duty
CAR DUMPERS
III
III
DRY DOCK CRANES
Re-Saw Merry-Go-Round
CAR PULLERS
II
III
DRY ERS & COOLERS
Slab
CEMENT KILNS
**
**
(Mills, Rotary)
III
Transfer
CENTRIFUGAL
DY EING MACHINERY
Cut-Off SawsChain & Drag
Blowers, Compressors,
(Textile)
II
II
Debarking Drums
Discharge Elevators,
ELEVATORS
Feeds - Edger
Fans or Pumps
I
II
Bucket - Uniform Load
I
II
Feeds - Gang
CHAIN CONVEY ORS
Bucket - Heavy Duty
II
II
Feeds - Trimmer
Uniformly Loaded or Fed
I
II
Bucket - Continuous
I
II
Log Deck
Heavy Duty
II
II
Centrifugal Discharge
I
II
Log Hauls- Incline-well type
CHEMICAL FEEDERS
Escalators
*
*
Log Turning devices
(Sewage)
I
II
Freight
*
*
Planer Feed
CLARIFIERS
I
II
Gravity Discharge
I
II
Planer Tilting Hoists
CLASSIFIERS
II
II
Man Lifts, Passenger
*
*
Rolls, Live Off Bearing
selectR2.p65
4
Black
7/19/2002, 10:50 AM
SERVICE
10
24
HRS/
HRS/
DAY
DAY
I
*
II
II
II
I
II
*
II
II
II
II
II
II
II
III
II
II
II
III
II
I
II
II
II
II
I
I
II
I
II
II
II
II
II
I
III
II
III
III
II
II
II
**
II
III
III
III
II
**
II
II
I
*
II
III
II
*
II
III
II
III
II
II
III
*
II
II
III
III
*
III
III
II
II
III
II
III
II
II
III
II
III
II
III
III
III
II
II
III
III
III
III
III
III
III
III
III
III
III
III
III
III
III
III
III
II
II
III
III
III
SELECTION PROCEDURES
Service Class Selections
TABLE 1 - SERVICE CLASSES (cont.)
SERVICE
10
24
HRS/
HRS/
DAY
DAY
II
III
*
*
SERVICE
10
24
HRS/
HRS/
DAY
DAY
II
III
II
APPLICAT ION
APPLICAT ION
APPLICAT ION
Tray Devices
Couch Rolls
Mills (3 on line)
Veneer Lathe Drives
Cutter
Mixing Mills
MACHINE TOOLS
Cylinder Molds
Refiners & Sheeters
Auxiliary Drives
I
II
Dryers
SAND MULLERS
Bending Rolls
II
II
Paper Machine & Conveyor Type
II
SCREENS
Main Drives
II
II
Embosser
II
Air Washing
Notching Press (Belted)
*
*
Extruder
III
Rotary Stone or Gravel
Plate Planers
III
III
Foundrinier Rolls
Traveling Water Intake
Punch Press (Geared)
III
III
Lumberbreaker, Wire Turning, Dandy
SCREW CONVEY ORS
Tapping Machines
III
III
& Return Rolls
II
Uniform
MANGLE (Textile)
II
II
Jordan
II
Heavy Duty or Feeder
MAST TUBS (Brewing &
Kiln Drive
III
SCUM BREAKERS (Sewage)
Distilling)
I
II
Mt. Hope & Paper Rolls
II
SEWAGE DISPOSAL
MEAT GRINDERS (Food)
II
II
Platter
II
Bar screens
METAL MILLS
Presses (Felt & Suction)
II
Chemical Feeders
Draw Bench Carriages &
Pulper continuous
II
Collectors
Main Drives
II
III
Repulper heavy stock
III
Dewatering Screens
Pinch, Dryer & Scrubber
Vacuum Pumps
II
Scum Breakers
Rolls Reversing
*
*
Reel (Surface Type)
II
Slow or Rapid Mixers
Slitters
II
II
Screens
Thickeners
Table Conveyors
Chip, Rotary
II
Vacuum Filters
Non-Reversing
Vibrating
III
SHAKER CONVEY ORS
Group drives
II
III
Size Press
II
SINGLE ACTING PUMPS
Individual
III
III
Super Calender
II
1 or 2 Cylinders
Reversing
*
*
Thickener & Washer
3 or more Cylinders
Wire Drawing & Flattening
AC Motor
II
SKIP HOIST
Machines
II
III
DC Motor
II
SLAB PUSHERS
Wire Winding Machines
II
II
Wind & Unwind Stand
I
SLITTERS (Metal Mills)
MILLS, ROTARY
Winders (Surface Type)
II
SLUDGE COLLECTORS
Ball and Rod Mills
Yankee Dryers
II
(Sewage)
with Spur Ring Gear
III
PASSENGERS ELEVATORS
*
*
SOAPERS (Textile)
with Helical Ring Gear
III
PEBBLE MILLS
III
SPINNERS (Textile)
Direct connected
III
PLASTIC INDUSTRY
STEERING GEARS
Kilns, Dryers, Coolers
PLATE PLANNERS
III
III
STOKERS
Pebble, Plain & Cement Kilns
*
*
PRINTING PRESSES
*
*
STONE CRUSHERS
Wedge bar
III
PROPORTIONING PUMPS
II
II
SUGAR INDUSTRY
Tumbling Barrels
III
III
PUG MILLS (Clay)
II
II
Cane, Knives, Crushers
MIXERS (Also see Agitators)
PULLERS (Barge Haul)
III
III
Mills (low speed end)
Concrete, Cont.
II
II
PUMPS
TABLE CONVEY ORS
Concrete, Int.
II
III
Centrifugal
I
II
(Non-Reversing)
Constant Density
I
II
Proportioning
II
II
Group Drives
Variable Density
II
II
Reciprocating Single Action
Individual Drives
NAPPERS (Textile)
II
II
3 or More Cylinders
II
II
Reversing
OIL INDUSTRY
Reciprocating Dbl Action
TENTER FRAMES (Textile)
Chillers
II
II
2 or More Cylinders
II
II
TEXTILE INDUSTRY
Oil Well Pumping
*
*
Reciprocating Single Action
Batchers, Calendars
Paraffin Filter Press
II
II
1 or 2 Cylinders
*
*
Card Machines
Rotary Kilns
II
II
Reciprocating Dbl Action
Dry Cans, Dryers
ORE CRUSHERS
III
III
1 Cylinder
*
*
Dyeing Machinery
OVEN CONVEY ORS
Rotary Gear, Lobe, Vane
I
II
Knitting Machinery
Uniform
I
II
PUNCH PRESSES
Looms, Mangles, Nappers, Pads
Heavy Duty
II
II
(Gear Driven)
III
III
Range Drives
PAPER MILLS z
RECIPROCATING
Slashers, Soapers, Spinners
Agitator (Mixer)
II
Conveyors, Feeders
III
III
Tenter Frames, Washers,
Agitator for Pure Liquors
II
RECIPROCATING
Winders
Barking Drums, Barkers
COMPRESSORS
THICKENERS (Sewage)
Mechanical
III
Multi-Cylinder
II
II
TUMBLING BARRELS
Beater
II
Single-Cylinder
III
III
VACUUM FILTERS (Sewage)
Breaker Stack
II
ROD MILLS
**
**
VANE BLOWERS
Calender
II
ROTARY
WINCHES (Dredges)
Chipper
III
Pumps
I
II
WINDERS (Textile)
Chip Feeder
II
Screens (Stone or Gravel)
II
II
WINDLASS
Coating Rolls
II
RUBBER & PLASTICS INDUSTRIES
WIRE
Conveyors
Calenders
II
II
Drawing Machines
Chip, Bark, Chemical
II
Crackers
III
III
Winding Machines
Log (Including Slab)
III
Mills (2 on line)
II
II
DRY DOCK CRANES (Hammerhead, Rotating and Whirler, Stationary or Moving) for any duration of service: Main Hoist, Auxiliary Hoist, Boom (Lifting): 3.00 S.F.;
Rotating (Swing or Slew): 3.00 S.F.; Tracking (Drive Wheels): 3.00 S.F.
z Service factors for paper mill application are applied to nameplate rating of electric motor at the motor rated base speed - consistent with TAPPI Standards.
When a super calender operates over a speed range of part constant hp and torque and the constant hp speed range is greater than 1.5:1, use a service factor of 1.0 at
base speed. When operating at constant torque over the entire speed range or when the constant hp speed range is less than 1.5:1 a 1.25 factor should be applied.
* Consult Factory.
** See Mills, Rotary.
Using anti-friction bearings only.
See Rubber & Plastics Industries
SERVICE
10
24
HRS/
HRS/
DAY
DAY
II
II
III
III
II
II
II
II
I
II
I
II
II
II
I
II
II
II
II
II
I
I
I
II
II
II
II
II
III
II
II
II
II
II
II
II
II
III
*
II
II
II
II
*
II
III
II
II
I
II
II
*
I
III
II
II
II
*
II
III
II
III
II
III
II
III
*
II
III
III
*
II
II
II
II
II
*
II
*
II
II
II
II
II
*
II
*
II
II
II
III
II
I
II
II
*
II
II
III
II
II
III
II
*
II
II
III
II
selectR2.p65
5
Black
7/19/2002, 10:51 AM
SELECTION PROCEDURES
Non-Motorized Selection (For motorized reducer selections, see page 2)
Introduction
Selection and pricing of Planetgear is based solely on the required output torque capacity of the application. The service factor method is
used to apply specific industry application standards based on the hours
per day of operation. These application standards are cataloged and
have been developed based on practical application experience.
The following information demonstrates how this procedure allows the
selection of the most economical Planetgear reducer.
Information Required To Make Reducer Selection
The specific application and hours per day of operation.
Reducer input speed.
Input Horsepower.
Desired reducer output speed.
If applicable, overhung load.
Single Cylinder
Engines
Multi-Cylinder
Engines
1.50
1.75
2.00
2.25
2.50
1.25
1.50
1.75
2.00
2.25
E.O.T. =
=
=
=
=
To
Motor horsepower
Nominal ratio from Step 3
Service factor from Step 2
Reducer input shaft speed in revolutions per
minute
Output torque required in lb-in
selectR2.p65
6
Black
7/19/2002, 10:51 AM
SELECTION PROCEDURES
Selection Examples Reducer Only (Non-motorized)
When motor horsepower is known:
A 100 hp 1,750 rpm motor is used to drive a heavy duty horizontal
apron conveyor 24 hrs/day. The conveyor requires a reducer output
speed of 50 rpm. A roller chain drive having a 240B25 tooth roller
chain sprocket (23.936" Pitch Diameter) is mounted with the center of
the chain pull 4.5 inches from the seal cage. Ambient temperature is
80 oF.
Step 1 Select service factor
From Table 2 on pages 7 & 8, the service factor for an apron conveyor
24 hrs/day operation is 1.5.
D.R. =
A heavy duty bucket elevator is operating 24 hrs/day. The elevator requires a reducer including backstop with a 157 rpm output speed (1,750
rpm input) and 24,000 lb-in output torque. Overhung and thrust loads
are not a factor. Reducer will be driven with a 60 hp motor.
Output Speed =
1,750 RPM
= 47.9 RPM
36.56
= 10,550 lbs.
The overhung load capacity from Table 11, page 100 for a Orion series
having a output speed approximately 48 rpm is 27,100 lbs. The rated
capacity is greater than the actual value, so the selection is approved.
This application does not encounter thrust load.
Step 8 Check dimensions
Dimensions for the Orion series are on page 72.
D.R. =
1,750 RPM
157 RPM
= 11.15
1,750 RPM
11.02
= 159 RPM
selectR2.p65
7
Black
7/19/2002, 10:51 AM
SELECTION PROCEDURES
Service Factor Selections
TABLE 2 - SERVICE FACTORS
SERVICE
10
24
HRS/
HRS/
DAY
DAY
SERVICE
10
24
HRS/
HRS/
DAY
DAY
1.25
1.50
1.25
1.50
1.00
1.25
APPLICAT ION
APPLICAT ION
APPLICAT ION
AGITATORS
Clay Working Machinery
FANS
Pure Liquids
1.00
1.25
Pug Mills
Centrifugal
Liquids & Solids
1.25
1.50 COLLECTORS (Sewage)
Cooling Towers
Liquids - Variable Density
1.25
1.50
Forced Draft
APRON CONVEY ORS
COMPRESSORS
Induced Draft
Uniformly Loaded or Fed
1.00
1.25
Centrifugal
1.00
1.25
Large (Mine, etc.)
Heavy Duty
1.25
1.50
Lobe
1.25
1.50
Large (Industrial)
APRON FEEDERS
1.25
1.50
Reciprocating
Light (Small Diameter)
ASSEMBLY CONVEY ORS
Multi-Cylinder
1.50
1.75 FEEDERS
Uniformly Loaded or Fed
1.00
1.25
Single Cylinder
2.25
2.50
Apron, Belt
Heavy Duty
1.25
1.50 CONCRETE MIXERS
Disc
BALL MILLS
**
**
Continuous
1.25
1.50
Reciprocating
BARGE HAUL PULLERS
1.75
2.00
Intermittent
1.25
1.50
Screw
BARKING
CONVEY ORS - Uniformly
FLIGHT
Drums (coupling connected)
2.00
Loaded or Fed: Apron,
Conveyors, Uniform
Mechanical
2.00
Assembly, Belt, Bucket, Chain
Conveyors, Heavy
BAR SCREENS (Sewage)
1.00
1.25
Flight, Oven, Screw
1.00
1.25 FOOD INDUSTRY
BATCHERS (Textile)
1.25
1.50 CONVEY OR - Heavy Duty
Beet Slicers
BELT CONVEY ORS
Not Uniformly Fed: Apron,
Bottling, Can Filling Mach
Uniformly Loaded or Fed
1.00
1.25
Assembly, Belt, Bucket, Chain
Cereal Cookers
Heavy Duty
1.25
1.50
Flight, Oven, Screw
1.25
1.50
Dough Mixers, Meat Grinders
BELT FEEDERS
1.25
1.50 CONVEY OR - Severe Duty
GENERATORS (Not Welding)
BENDING ROLLS (Machine)
1.25
1.50
Live Roll
*
*
GRAVITY DISCHARGE
BLOWERS
Reciprocating, Shaker
1.75
2.00
ELEVATORS
Centrifugal
1.00
1.25 COOKERS (Brewing & Distilling)
HAMMER MILLS
Lobe
1.25
1.50
(Food)
1.00
1.25 HOISTS
Vane
1.00
1.25 COOLING TOWER FANS
*
*
Heavy Duty
BOTTLING MACHINERY
1.00
1.25 CRANES
Medium Duty
1.50
Driving Processing Equip
Scale Hoppers, Freq. Starts
1.25
1.50 DEWATERING SCREENS
Other Line Shafts, Light
BRICK PRESS (Clay Working)
1.75
2.00
(Sewage)
1.25
1.50 LIVE ROLL CONVEY ORS
BRIQUETTE MACHINES
DISC FEEDERS
1.00
1.25 LOBE BLOWERS OR COMPRESSORS
(Clay Working)
1.75
2.00 DISTILLING (See Brewing)
LOG HAULS (Lumber)
BUCKET
DOUBLE ACTING PUMPS
Incline-well Type
Conveyors Uniform
1.00
1.25
2 or More Cylinders
1.25
1.50 LOOMS (Textile)
Conveyors Heavy Duty
1.25
1.50
Single Cylinder
*
*
LUMBER INDUSTRY
Elevators Cont.
1.00
1.25 DOUGH MIXER (Food)
1.25
1.50
Barkers - Spindle Feed
Elevators Uniform
1.00
1.25 DRAW BENCH (Metal Mills)
Barkers - Main Drive
Elevators Heavy duty
1.25
1.50
Carriage & Main Drive
1.25
1.50
Carriage Drive
CALENDERS
DREDGES
Chain - Floor
Rubber
1.50
1.50
Cable Reels, Conveyors
1.25
1.50
Chains - Green
Textile
1.25
1.50
Cutter Head & Jig Drives
1.75
2.00
Conveyors
CAN FILLING MACHINES
1.00
1.25
Maneuvering Winches, Pumps
1.25
1.50
Burner
CANE KNIVES
1.50
1.50
Screen Drives
1.75
2.00
Main or Heavy Duty
CARD MACHINES (Textile)
1.25
1.50
Stackers, Utility Winches
1.25
1.50
Main Log
CAR DUMPERS
1.75
2.00 DRY DOCK CRANES
Re-Saw Merry-Go-Round
CAR PULLERS
1.25
1.50 DRY ERS & COOLERS
Slab
CEMENT KILNS
**
**
(Mills, Rotary)
1.50
Transfer
CENTRIFUGAL
DY EING MACHINERY
Cut-Off SawsChain & Drag
Blowers, Compressors,
(Textile)
1.25
1.50
Debarking Drums
Discharge Elevators,
ELEVATORS
Feeds - Edger
Fans or Pumps
1.00
1.25
Bucket - Uniform Load
1.00
1.25
Feeds - Gang
CHAIN CONVEY ORS
Bucket - Heavy Duty
1.25
1.50
Feeds - Trimmer
Uniformly Loaded or Fed
1.00
1.25
Bucket - Continuous
1.00
1.25
Log Deck
Heavy Duty
1.25
1.50
Centrifugal Discharge
1.00
1.25
Log Hauls- Incline-well type
CHEMICAL FEEDERS
Escalators
*
*
Log Turning devices
(Sewage)
1.00
1.25
Freight
*
*
Planer Feed
CLARIFIERS
1.00
1.25
Gravity Discharge
1.00
1.25
Planer Tilting Hoists
CLASSIFIERS
1.25
1.50
Man Lifts, Passenger
*
*
Rolls, Live Off Bearing
selectR2.p65
8
Black
7/19/2002, 10:51 AM
SERVICE
10
24
HRS/
HRS/
DAY
DAY
1.00
*
1.25
1.25
1.25
1.00
1.25
*
1.25
1.50
1.50
1.50
1.25
1.25
1.00
1.75
1.25
1.50
1.25
2.00
1.50
1.00
1.25
1.25
1.50
1.25
1.00
1.00
1.25
1.00
1.50
1.25
1.25
1.50
1.25
1.00
1.75
1.25
2.00
1.75
1.25
1.25
1.25
**
1.25
2.00
1.50
1.50
1.50
**
1.50
1.25
1.00
*
1.25
1.50
1.25
*
1.50
1.75
1.25
1.75
1.50
1.25
1.75
*
1.50
1.50
1.50
1.75
*
1.50
1.75
1.25
1.50
1.75
1.25
1.75
1.25
1.50
1.75
1.25
1.75
1.25
2.00
1.75
1.75
1.25
1.50
1.50
1.50
2.00
1.50
2.00
1.50
1.75
2.00
1.50
1.75
1.50
2.00
1.75
1.75
1.50
1.50
1.75
1.25
1.50
1.75
1.50
1.75
SELECTION PROCEDURES
Service Factor Selections
TABLE 2 - SERVICE FACTORS (cont.)
SERVICE
10
24
HRS/
HRS/
DAY
DAY
1.25
1.50
*
*
SERVICE
10
24
HRS/
HRS/
DAY
DAY
1.25
2.00
1.25
APPLICAT ION
APPLICAT ION
APPLICAT ION
Tray Devices
Couch Rolls
Mills (3 on line)
Veneer Lathe Drives
Cutter
Mixing Mills
MACHINE TOOLS
Cylinder Molds
Refiners & Sheeters
Auxiliary Drives
1.00
1.25
Dryers
SAND MULLERS
Bending Rolls
1.25
1.50
Paper Machine & Conveyor Type
1.25 SCREENS
Main Drives
1.25
1.50
Embosser
1.25
Air Washing
Notching Press (Belted)
*
*
Extruder
1.50
Rotary Stone or Gravel
Plate Planers
1.75
2.00
Foundrinier Rolls
Traveling Water Intake
Punch Press (Geared)
1.75
2.00
Lumberbreaker, Wire Turning, Dandy
SCREW CONVEY ORS
Tapping Machines
1.75
2.00
& Return Rolls
1.25
Uniform
MANGLE (Textile)
1.25
1.50
Jordan
1.50
Heavy Duty or Feeder
MAST TUBS (Brewing &
Kiln Drive
1.50
Bar screens
METAL MILLS
Presses (Felt & Suction)
1.25
Chemical Feeders
Draw Bench Carriages &
Pulper continuous
1.50
Collectors
Main Drives
1.25
1.50
Repulper heavy stock
2.00
Dewatering Screens
Pinch, Dryer & Scrubber
Vacuum Pumps
1.50
Scum Breakers
Rolls Reversing
*
*
Reel (Surface Type)
1.25
Slow or Rapid Mixers
Slitters
1.25
1.50
Screens
Thickeners
Table Conveyors
Chip, Rotary
1.50
Vacuum Filters
Non-Reversing
Vibrating
2.00
SHAKER CONVEY ORS
Group drives
1.25
1.50
Size Press
1.25 SINGLE ACTING PUMPS
Individual
1.75
2.00
Super Calender
1.25
1 or 2 Cylinders
Reversing
*
*
Thickener & Washer
3 or more Cylinders
Wire Drawing & Flattening
AC Motor
1.25
(Sewage)
with Spur Ring Gear
Direct connected
1.50
Conveyors, Feeders
1.75
2.00
Tenter Frames, Washers,
Agitator for Pure Liquors
1.25 RECIPROCATING
Winders
Barking Drums, Barkers
COMPRESSORS
THICKENERS (Sewage)
Mechanical
2.00
Multi-Cylinder
1.25
1.50
TUMBLING BARRELS
Beater
1.50
Single-Cylinder
2.25
2.50
VACUUM FILTERS (Sewage)
Breaker Stack
1.25 ROTARY
WINCHES (Dredges)
Chipper
2.00
Pumps
1.00
1.25
WINDERS (Textile)
Chip Feeder
1.50
Screens (Stone or Gravel)
1.25
1.50
WINDLASS
Coating Rolls
1.25
Crackers
2.00
2.00
Winding Machines
Log (Including Slab)
2.00
Mills (2 on line)
1.50
1.50
DRY DOCK CRANES (Hammerhead, Rotating and Whirler, Stationary or Moving) for any duration of service: Main Hoist, Auxiliary Hoist, Boom (Lifting): 3.00 S.F.;
Rotating (Swing or Slew): 3.00 S.F.; Tracking (Drive Wheels): 3.00 S.F.
z Service factors for paper mill application are applied to nameplate rating of electric motor at the motor rated base speed - consistent with TAPPI Standards.
When a super calender operates over a speed range of part constant hp and torque and the constant hp speed range is greater than 1.5:1, use a service factor of 1.0 at
base speed. When operating at constant torque over the entire speed range or when the constant hp speed range is less than 1.5:1 a 1.25 factor should be applied.
* Consult Factory.
** See Mills, Rotary.
Using anti-friction bearings only.
See Rubber & Plastics Industries
SERVICE
10
24
HRS/
HRS/
DAY
DAY
1.25
1.25
1.50
1.50
1.50
1.50
1.25
1.50
1.00
1.25
1.00
1.25
1.50
1.25
1.00
1.25
1.25
1.25
1.50
1.50
1.00
1.00
1.00
1.25
1.25
1.25
1.25
1.25
1.75
1.25
1.25
1.25
1.50
1.50
1.50
1.50
1.50
2.00
*
1.25
1.25
1.25
1.25
*
1.50
1.50
1.50
1.50
1.00
1.25
1.25
*
1.00
1.75
1.25
1.50
1.50
*
1.25
2.00
1.50
2.00
1.50
2.00
1.25
1.75
*
1.25
1.50
2.00
*
1.50
1.25
1.25
1.25
1.25
*
1.25
*
1.25
1.50
1.50
1.50
1.50
*
1.50
*
1.50
1.25
1.25
1.75
1.25
1.00
1.25
1.25
*
1.50
1.50
2.00
1.50
1.25
1.50
1.50
*
1.25
1.25
1.50
1.50
selectR2.p65
9
Black
7/19/2002, 10:52 AM
SELECTION PROCEDURES
Thrust and Overhung Loads
Thrust Loads
Example:
Thrust loads applied to reducer shafts through coupling connections often are combined with radial shaft loads. Since this combined loading
affects bearing thrust capacities, these values may be obtained by contacting the factory.
Overhung Loads
The center line of the overhung load should be as close as possible to
the seal cage to minimize bearing load and improve bearing life. The
formula for determining overhung load in pounds is as follows:
A 10 HP, 1,750 RPM motor with 5.5" Pitch diameter sheave is V-belt
connected to an 8.2" sheave mounted on an Atlas series reducer having
a ratio of 54.45, an output torque capacity of 30,000 lb.-in. and a 21.5
RPM output speed. The centerline of the sheave on the reducer is
mounted two inches from the seal cage. Calculate the high speed shaft
overhung load.
Solution:
126,000 x HP x FC x LF
P.D. x RPM
1,750 x 5.5
= 1,170 RPM
8.2
Table 10, page 100 - 1170 RPM yields an overhung load capacity of
1,060 pounds for the Atlas series reducer. The actual load of 201 pounds
is less than the capacity rating and is acceptable for this selection.
Low Speed Shaft
The load locations factor (LF) are shown in Table 9, page 99. The overhung load capacity ratings for low speed shafts are listed in Table 11,
page 100.
Example:
If the actual overhung load exceeds the published capactiy, the following may be assistance to reduce the overhung load on the shaft bearings.
1. Increase the pitch diameter of sheave or sprocket.
2. Locate the sprocket or belt closer to the seal cage.
3. Go to the next larger reducer series.
O.H.L. =
The overhung load rating listed in Table 11, page 100, for the Mars
reducer at a ratio of 24.00 is 3,620 pounds. The actual load of 1,786 is
less than the rated capacity and is acceptable for this application.
Published values of overhung loads in Tables 10 and 11 are based on
the load being applied at 1 shaft diameter away from the seal cage.
selectR2.p65
10
Black
7/19/2002, 10:52 AM
SELECTION PROCEDURES
Reducer Order Form
Reducer Order Form
Mars
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
Mounting Orientation:
Horizontal
Inclined
____ Degrees High Speed Shaft Up
____ Degrees Low Speed Shaft Up
Vertical
High Speed Shaft Up
Low Speed Shaft Up
Rotated
____ Degrees Clockwise Rotation (viewing Low Speed Shaft)
____ Degrees Counter Clockwise Rotation (viewing Low Speed Shaft)
Rating Information:
Torque Rating:
Motorized:
Input RPM:
Ratio:
Output RPM:
Motor HP:
Service Class:
Non-Motorized:
Service HP:
Service Factor:
Motorized Reducers:
Basic Configuration
Scoop Mount with Omega coupling
(Frame Size __________)
or
Input C-face (Frame Size __________)
Optional Accessories
Coupling Guard
Fan & Shroud
Backstop (Rotation CW or CCW)
Slidebase
Vertical Modification
High Temperature Seals
Extended Shafts
Motor
Optional Accessories
Couplings
Coupling Guard
Fan & Shroud
Backstop (Rotation CW or CCW)
Slidebase
Vertical Modification
High Temperature Seals
Extended Shafts
Motor
10
selectR2.p65
11
Black
7/19/2002, 10:52 AM
SELECTION TABLES
1750 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
1 5 HP
254T
MERC 2
MERC 4
MARS 5
2 0 HP
256T
MERC 4
MERC 4
MARS 5
2 5 HP
284T
MERC 4
MARS 5
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
8
10
MARS
VENS
10
14
102
86
86
73
73
MERC
MERC
MERC
2
2
1
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MERC
MARS
MARS
6
8
10
MARS
MARS
MARS
9
12
14
MARS
VENS
VENS
13
15
18
VENS
VENS
VENS
15
17
22
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
MERC
MERC
MERC
MERC
2
3
3d
2
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MARS
MARS
6
7
8d
9
MARS
MARS
MARS
MARS
9
11
12
15
MARS
MARS
MARS
VENS
11
13
16
20
VENS
VENS
VENS
ATLS
17
19
24
30
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ATLS
ERTH
32
33
41
48
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
MERC
MERC
MERC
4
3
4
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
5
6
MERC
MERC
MARS
8
7
9
MARS
MARS
MARS
11
13
15
MARS
VENS
VENS
17
18
20
VENS
ATLS
ATLS
22
27
30
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
50
56
ERTH
ERTH
ERTH
54
62
68
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
MERC
MERC
MERC
4
5
4
MERC
MERC
MERC
6
7
6
MERC
MERC
MERC
8
7
8
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
17
17
20
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ATLS
34
36
38
ERTH
ERTH
ERTH
48
52
56
NEPT
ERTH
ERTH
70
70
74
NEPT
PLRS
PLRS
80
85
100
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
MERC
MERC
MERC
5q
5
6
MERC
MARS
MERC
7q
9
8
MARS
MARS
MARS
9q
11
11
ATLS
ATLS
ATLS
30q
35
43q
ERTH 44q
ERTH 46
ERTH 50q
ERTH 62q
ERTH 70
ERTH 74q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
MERC 7
MERC 8
MARS 9
MARS 10t
MARS
MARS
MARS
MARS
11
11
13
13
MARS
MARS
MARS
VENS
15
13
17
18
VENS
VENS
VENS
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
33
35
39
43
ERTH
ERTH
ERTH
ERTH
48
52
58
64
ERTH 64q
ERTH 70
ERTH 76
PLRS 90
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
MARS
MARS
MARS
11
12
14
MARS
MARS
VENS
15
18
20
VENS
VENS
VENS
20
23
24
ATLS
ATLS
ATLS
31
32
39
ERTH
ERTH
ERTH
48
58
64
ERTH
PLRS
PLRS
72
80
90
PLRS
PLRS
PLRS
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
MARS
MARS
MARS
14
16
18
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
66
76
95
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
VENS 21 ATLS 32 ERTH 46 ERTH 64 PLRS 110 NEPT 160 ORON 215
ERTH 30q u ERTH 36q u ERTH 48q u PLRS 70q u NEPT 120q u NEPT 160q u ORON 240
VENS 24 ATLS 35 ERTH 54 PLRS 85 NEPT 135 ORON 190 SATN 265
9 0 0 .3
1057
1 .9
1 .7
ATLS
ERTH
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
1 7 .2 1
2 0 .4 1
2 4 .0 0
32
36
ERTH 48q u PLRS 65q u PLRS 95q u NEPT 150q u ORON 215
ERTH 54 PLRS 70q u PLRS 100q u ORON 190 SATN 280
NEPT
ORON
ORON
ORON
160q
190
205
215
TITN
TITN
JUPT
350
400
450
550
550
265
300
390
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
11
1750rR2.p65
10
Black
7/19/2002, 10:21 AM
SELECTION TABLES
1750 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
3 0 HP
286T
MERC 4
MARS 5
MARS 7
ATLS 14
VENS 13
VENS 16
4 0 HP
324T
VENS 10
MARS 7
VENS 11
ATLS 14
VENS 17
VENS 20
5 0 HP
326T
VENS 10
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
6 0 HP
364T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
7 5 HP
365T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
1 0 0 HP
405T
ERTH 18
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
1 2 5 HP
444T
NEPT 45
ERTH 20
ERTH 34
PLRS 44
PLRS 50
PLRS 65
1 7 .2 1
2 0 .4 1
2 4 .0 0
102
86
86
73
73
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
58
70
90
PLRS
PLRS
NEPT
75 NEPT
90 PLRS
105 NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
62t
64
85
100
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
80t
100
115
150
NEPT
NEPT
ORON
ORON
120 ORON
130 ORON
175 ORON
195 SATN
155 ORON
170 ORON
200 SATN
240 TITN
170
185
230
320
TITN
TITN
TITN
TITN
280
280
340
400
JUPT 400
JUPT 300d
JUPT 500
JUPT 450
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
90
95
110
PLRS
NEPT
NEPT
110 NEPT
125 NEPT
140 NEPT
SATN
TITN
TITN
270
320
350
TITN
TITN
TITN
340
360
430
JUPT
JUPT
JUPT
450
450
550
JUPT
JUPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
NEPT
PLRS
PLRS
100 NEPT
105 NEPT
110 NEPT
JUPT
TITN
JUPT
400
420
500
JUPT
450
JUPT
600
JUPT
550
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
PLRS 120q NEPT 160q ORON 205q SATN 260q SATN 300q TITN 400q JUPT
NEPT 140 ORON 190 ORON 240 SATN 280 TITN 340 JUPT 500
NEPT 150q ORON 215 SATN 260q SATN 300q TITN 400q JUPT 550 JUPT
550
JUPT
650
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
ORON
ORON
ORON
SATN
TITN
TITN
TITN
TITN
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
SATN
TITN
TITN
280
320
360
TITN
TITN
JUPT
380
440
500
JUPT
JUPT
JUPT
500
550
600
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
TITN
TITN
JUPT
430
440
500
JUPT
JUPT
550
600
JUPT
650
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
JUPT
650
9 0 0 .3
1057
1 .9
1 .7
JUPT
JUPT
SATN
SATN
SATN
JUPT
JUPT
JUPT
JUPT
240
250
300
JUPT
TITN
TITN
300
340
400
1 5 0 HP
445T
PLRS 32
NEPT 45
NEPT 70
NEPT 80
PLRS 75
2 0 0 HP
2 5 0 HP
NEPT 45
NEPT 70
TITN 210
NEPT 95
NEPT 55
TITN 220
550
550
650
500
550
600
650
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1750rR2.p65
12
11
Black
7/19/2002, 10:22 AM
SELECTION TABLES
1750 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
1 7 .2 1
2 0 .4 1
2 4 .0 0
continued
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
3 HP
182T
MERC 2
MERC 2
MERC 1
5 HP
184T
MERC 2
MERC 2
MERC 3
7 .5 HP
213T
MERC 2
MERC 2
MERC 3
1 0 HP
215T
MERC 2
MERC 4
MERC 3
1 5 HP
254T
MERC 4
MERC 4
MARS 5
2 0 HP
256T
MERC 4
MARS 5
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
5
6
MERC
MERC
5
6
MARS
MARS
8
10
MARS
MARS
10
12
2 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 13
VENS 16
102
86
86
73
73
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
4
6
7
MERC
MARS
MARS
6
8
8
MARS
MARS
MARS
9
10
12
MARS
VENS
VENS
13
15
16
VENS
VENS
VENS
15
17
22
VENS
VENS
ATLS
19
21
26
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
4
5
7
8
MARS 7
MARS 9
MARS 10d
MARS 13
MARS
MARS
MARS
MARS
11
13
16
17
MARS
VENS
VENS
VENS
13
17
20
24
ATLS
VENS
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ATLS
ERTH
32
33
41
48
ATLS
ATLS
ERTH
ERTH
34t
41
48
60
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
MERC
MERC
MERC
4
3
4
MERC
MERC
MERC
6
5
6
MERC
MERC
MERC
6
7
8
MARS
MARS
MARS
9
9
11
MARS
MARS
MARS
15
15
17
VENS
VENS
ATLS
20
22
26
ATLS
ATLS
ATLS
30
31
34
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
54
62
68
ERTH
PLRS
PLRS
66
75
90
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
13
13
15
ATLS
VENS
VENS
22
21
24
ATLS
ATLS
ATLS
30
32
38
ERTH
ERTH
ERTH
42
46
50
NEPT
ERTH
ERTH
60
64
74
NEPT
PLRS
PLRS
80 NEPT
85 PLRS
100 PLRS
100
105
120
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
MERC
MERC
MERC
5q
7
8
MARS
MARS
MARS
9q
9
11
ATLS
ATLS
ATLS
26q
31
35q
ATLS 38q
ATLS 43q
ERTH 50q
ERTH 50q
ERTH 58
ERTH 62q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
MARS
MARS
MARS
MARS
9
9
11
13
MARS
MARS
MARS
MARS
13
13
15
17
VENS
MARS
VENS
VENS
16
17
20
22
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ERTH
ATLS
ERTH
ERTH
42
43
52
58
ERTH
ERTH
ERTH
PLRS
60
70
76
80
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
MARS
MARS
MARS
13
14
16
VENS
VENS
VENS
18
21
24
VENS
ATLS
ATLS
24
28
31
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
60
70
76
PLRS
PLRS
PLRS
95 NEPT
100 NEPT
120 NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
MARS
VENS
VENS
18
19
22
ATLS
ATLS
ATLS
27
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
54
58
72
PLRS
PLRS
PLRS
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
ATLS
ERTH
36
48
SATN
SATN
TITN
160q
190
205
215
260
280
350
SATN
SATN
TITN
250
280
350
ORON
ORON
SATN
SATN
190Q
215
260
280
TITN
TITN
TITN
300
360
400
TITN
TITN
JUPT
350
400
450
TITN
JUPT
JUPT
430
500
550
550
550
JUPT
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
13
1750rR2.p65
12
Black
7/19/2002, 10:22 AM
SELECTION TABLES
1750 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
496
399
286
188
159
126
3 0 HP
286T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
4 0 HP
324T
VENS 10
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
5 0 HP
326T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
1 7 .2 1
2 0 .4 1
2 4 .0 0
102
86
86
73
73
ATLS
ATLS
ATLS
22
26
34
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
46
54
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
58
64
80
PLRS
PLRS
NEPT
75 NEPT
90 NEPT
105 NEPT
SATN
SATN
TITN
190
210
270
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ERTH
ERTH
PLRS
PLRS
60t
64
85
100
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
80t
100
115
150
NEPT
NEPT
NEPT
ORON
110 NEPT
120 ORON
150 ORON
180 SATN
140t ORON
170 ORON
200 SATN
240 TITN
170
200
245
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
320
380
450
JUPT
JUPT
JUPT
JUPT
400
400
500
550
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
PLRS
PLRS
PLRS
80 PLRS
95 NEPT
100 NEPT
SATN
TITN
TITN
270
320
350
TITN
TITN
TITN
340
400
430
TITN
JUPT
JUPT
420
450
500
JUPT
JUPT
550
550
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
NEPT
NEPT
NEPT
JUPT
JUPT
JUPT
400
450
500
JUPT
500
JUPT
600
JUPT
600
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
NEPT 150q ORON 205q SATN 260q SATN 300q TITN 400q JUPT
ORON 190 ORON 240 TITN 300 TITN 340 JUPT 500
ORON 190q SATN 260Q TITN 320q TITN 400q JUPT 500 JUPT
550
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
ORON
ORON
SATN
SATN
240q
240
260
300
TITN
TITN
TITN
TITN
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
TITN
TITN
JUPT
380
400
450
JUPT
JUPT
JUPT
500
550
600
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
JUPT
JUPT
JUPT
550
600
650
JUPT
650
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
JUPT
SATN
SATN
SATN
JUPT
JUPT
JUPT
JUPT
240
250
300
500
550
600
650
JUPT
TITN
TITN
JUPT
300
340
360
1 5 0 HP
445T
PLRS 32
NEPT 45
NEPT 70
NEPT 80
NEPT 95
2 0 0 HP
2 5 0 HP
NEPT 55 NEPT 65
NEPT 90
650
650
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
14
1750rR2.p65
13
Black
7/19/2002, 10:23 AM
SELECTION TABLES
1750 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
1 5 HP
254T
MERC 4
MERC 4
MARS 5
2 0 HP
256T
MERC 4
MARS 5
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MERC
MARS
5
8
MARS
MARS
8
12
MARS
VENS
10
14
2 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
102
86
86
73
73
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MARS
MARS
MARS
7
8
10
MARS
MARS
MARS
9
12
12
MARS
VENS
VENS
13
15
18
VENS
VENS
ATLS
17
19
26
VENS
VENS
ATLS
21
23
30
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
3
5d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MARS
MARS
MARS
MARS
9
9
12
13
MARS
MARS
MARS
VENS
11
15
16
20
VENS
VENS
VENS
ATLS
17
19
22
30
ATLS
ATLS
ATLS
ATLS
24
29
33
42
ATLS
ATLS
ERTH
ERTH
32
37
48
54
ATLS
ERTH
ERTH
ERTH
38t
46
54
66
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
MERC
MERC
MERC
4
5
4
MERC
MERC
MERC
6
5
6
MERC
MERC
MERC
8
7
8
MARS
MARS
MARS
11
11
13
MARS
MARS
VENS
17
17
20
VENS
ATLS
ATLS
24
27
30
ATLS
ATLS
ATLS
30
35
38
ERTH
ERTH
ERTH
48
50
56
ERTH
ERTH
ERTH
60
68
74
PLRS
PLRS
PLRS
80
85
100
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
MERC
MERC
MERC
6
5
6
MERC
MARS
MERC
8
9
8
MARS
MARS
MARS
9
11
11
MARS
MARS
MARS
13
15
17
ATLS
VENS
ATLS
22
23
26
ATLS
ATLS
ATLS
34
36
42
ERTH
ERTH
ERTH
48
46
56
NEPT
ERTH
PLRS
70
70
80
NEPT
PLRS
PLRS
90
95
110
NEPT
NEPT
NEPT
110
115
130
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
MERC
MERC
MERC
7q
7
8
MARS
MARS
MARS
9q
11
13
ATLS
ATLS
ATLS
30q
35
39q
ERTH 44q
ERTH 52
ERTH 56q
ERTH 56q
ERTH 64
ERTH 74q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
MARS
MARS
MARS
MARS
11
11
13
13
MARS
MARS
MARS
VENS
15
15
17
18
VENS
VENS
VENS
VENS
18
20
22
24
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
48
52
58
64
ERTH 64q
ERTH 76
PLRS 80
PLRS 90
PLRS 90q
PLRS 100
PLRS 110
PLRS 120
NEPT
NEPT
NEPT
ORON
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
MARS
MARS
MARS
15
16
18
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
PLRS
66
76
90
PLRS
PLRS
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
VENS
VENS
VENS
20
21
24
ATLS
ATLS
ATLS
31
32
35
ATLS
ERTH
ERTH
39
46
54
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
ERTH 42q u PLRS 65q u PLRS 85q u NEPT 130q u ORON 215
ERTH 54 PLRS 70q u PLRS 100q u ORON 190 ORON 240
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
1 7 .2 1
2 0 .4 1
2 4 .0 0
140q
150
160
190
ORON
ORON
ORON
ORON
190q
215
230
240
ORON
ORON
SATN
SATN
215q
240
270
300
SATN
SATN
TITN
280
300
360
TITN
TITN
TITN
340
400
440
TITN
TITN
JUPT
390
440
500
JUPT
JUPT
JUPT
500
550
600
600
SATN
TITN
TITN
280
320
390
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
15
1750rR2.p65
14
Black
7/19/2002, 10:23 AM
SELECTION TABLES
1750 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
496
399
286
188
159
126
3 0 HP
286T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 17
VENS 20
4 0 HP
324T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
5 0 HP
326T
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 34
1 7 .2 1
2 0 .4 1
2 4 .0 0
102
86
86
73
73
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
46
46
60
ERTH
ERTH
PLRS
52
58
70
ERTH
ERTH
PLRS
64
70
90
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
62t
70
85
110
PLRS
PLRS
PLRS
NEPT
80t NEPT
90 PLRS
115 NEPT
140 ORON
100
110
130
180
NEPT
NEPT
ORON
ORON
120 NEPT
130 ORON
175 ORON
210 SATN
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
PLRS
PLRS
PLRS
90 PLRS
105 NEPT
110 NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
SATN
NEPT
NEPT
240
250
270
SATN
SATN
TITN
260
280
320
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
TITN
TITN
TITN
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
TITN
JUPT
JUPT
420
450
500
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
JUPT
550
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
JUPT
JUPT
SATN
SATN
SATN
HP
2 5 0 HP
65 NEPT 75
100
210
SATN
SATN
TITN
175
190
230
TITN
TITN
TITN
150t SATN
185 SATN
225 TITN
270 TITN
200
220
300
360
TITN
TITN
TITN
TITN
280
280
340
400
TITN
TITN
JUPT
JUPT
320
360
500
500
JUPT 400
JUPT 450d
JUPT 500
JUPT 600
TITN
TITN
TITN
300
360
390
TITN
JUPT
JUPT
380
450
500
JUPT
JUPT
JUPT
450
500
600
JUPT
JUPT
600
640
JUPT
JUPT
JUPT
450
500
550
JUPT
550
JUPT
650
JUPT
650
600
350
380
400
PLRS
PLRS
NEPT
1 5 0 HP
200
445T
PLRS 32
NEPT 45 NEPT
NEPT 70 NEPT
NEPT 80 TITN
NEPT 105 ORON
240
240
310
600
550
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1750rR2.p65
16
15
Black
7/19/2002, 10:24 AM
SELECTION TABLES
1750 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
1 5 HP
254T
MERC 4
MERC 4
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
102
86
86
73
73
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MARS
MARS
MARS
7
10
10
MARS
MARS
MARS
9
12
14
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
3
5d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MARS
MARS
MARS
MARS
9
11
12t
15
MARS
MARS
VENS
VENS
13
15
18
22
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MERC
MARS
8
7
9
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
17
18
20
VENS
ATLS
ATLS
24
27
30
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
MERC
MERC
MERC
6
7
6
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
15
17
18
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ATLS
38
40
42
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
MERC
MARS
MERC
7
9
8
MARS
MARS
MARS
9
11
13
MARS
MARS
MARS
13
15
17
ATLS 22q
VENS 21
ATLS 27q
ATLS
ATLS
ATLS
30q
35
43q
ERTH 50q
ERTH 52
ERTH 56q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
MARS
MARS
MARS
MARS
11
11
13
13
MARS
MARS
VENS
VENS
15
15
18
20
VENS
VENS
VENS
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
48
52
58
64
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
MARS
MARS
VENS
15
18
20
VENS
ATLS
ATLS
22
24
27
ATLS
ATLS
ATLS
31
32
39
ERTH
ERTH
ERTH
48
52
58
ERTH
PLRS
PLRS
72
80
90
PLRS
PLRS
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
9 0 0 .3
1057
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
1 7 .2 1
2 0 .4 1
2 4 .0 0
8
12
2 0 HP
256T
MERC 4
MARS 5
MARS 7
ATLS 14
VENS 15
VENS 14
2 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
VENS
VENS
VENS
15
15
20
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
22
26
34
17
21
24
30
ATLS
ATLS
ATLS
ERTH
28
29
37
48
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
56
62
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
80
95
100
ERTH
ERTH
ERTH
48
52
56
NEPT
PLRS
PLRS
80
75
90
NEPT
PLRS
PLRS
100 NEPT
105 NEPT
110 NEPT
120
125
140
ERTH 62q
ERTH 70
ERTH 74q
ORON
ORON
ORON
SATN
190q ORON
215 SATN
230 SATN
260 TITN
240q
260
300
320
SATN
TITN
TITN
280
320
360
TITN
TITN
JUPT
380
400
450
TITN
TITN
JUPT
430
440
500
JUPT
JUPT
JUPT
550
550
650
2 .8
2 .6
2 .4
ATLS 32 ERTH 46 ERTH 64 PLRS 100 NEPT 160 ORON 240 TITN 320 JUPT 500 JUPT
ERTH 36q u ERTH 54q u PLRS 70q u PLRS 100q u NEPT 160q u ORON 260q u TITN 320q u JUPT 500
ATLS 35 ERTH 60 PLRS 85 PLRS 115 ORON 190 TITN 310 TITN 390 JUPT 550q u
650
1 .9
1 .7
ERTH 48q u PLRS 75q u PLRS 95q u NEPT 140q u ORON 240
ERTH 54 PLRS 80q u PLRS 100q u ORON 190 SATN 280
TITN
TITN
TITN
310
360
430
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
17
1750rR2.p65
16
Black
7/19/2002, 10:24 AM
SELECTION TABLES
1750 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
496
399
286
188
159
126
3 0 HP
286T
MARS 6
VENS 10
VENS 11
ATLS 18
VENS 19
VENS 22
4 0 HP
324T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
5 0 HP
326T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
1 7 .2 1
2 0 .4 1
2 4 .0 0
102
86
86
73
73
ATLS
ATLS
ATLS
30
30
38
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
ERTH
ERTH
PLRS
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
PLRS
PLRS
PLRS
110 NEPT
105 NEPT
120 NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
TITN
JUPT
JUPT
420
500
550
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
JUPT
550
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
46
52
66
80t NEPT
100 PLRS
115 NEPT
150 ORON
58
64
80
PLRS
PLRS
NEPT
75
80
95
NEPT
PLRS
NEPT
175
210
270
TITN
TITN
TITN
240
280
310
170
185
230
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
280
380
450
TITN
JUPT
JUPT
JUPT
320
400
500
550
JUPT
JUPT
JUPT
400
450
550
JUPT
JUPT
JUPT
500
500
600
JUPT
650
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
420
450
500
JUPT
TITN
TITN
350
380
440
JUPT
450
JUPT
600
JUPT
550
500
JUPT
650
JUPT
JUPT
JUPT
JUPT
240
250
300
500
550
600
650
JUPT
TITN
TITN
JUPT
300
300
360
2 5 0 HP
65 NEPT 85
100
125
SATN
SATN
TITN
240
280
300
SATN
SATN
SATN
HP
SATN
SATN
SATN
JUPT
JUPT
1 5 0 HP
200
445T
PLRS 42
NEPT 55 NEPT
NEPT 80 NEPT
NEPT 90 ORON
NEPT 115 ORON
600
650
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
18
1750rR2.p65
17
Black
7/19/2002, 10:25 AM
SELECTION TABLES
1750 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
5
6
MERC
MARS
5
8
MARS
MARS
102
86
86
73
73
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
3
MERC
MERC
MERC
4
4
5
MERC
MARS
MARS
6
8
8
MARS
MARS
MARS
9
10
12
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
4
5
7
8
MERC
MERC
MARS
MARS
6
7
8d
11
MARS
MARS
MARS
MARS
11
13
14
17
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
13
13
15
VENS
VENS
VENS
20
22
24
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
11
13
15
MARS
VENS
VENS
17
17
20
ATLS
ATLS
ATLS
30
32
34
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
MERC
MARS
MARS
7q
9
11
ATLS 34q
ATLS 43q
ERTH 44q
ERTH 56q
ERTH 64
ERTH 68q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
MARS
MARS
MARS
MARS
13
13
15
15
VENS
MARS
VENS
VENS
18
17
22
24
ATLS
ATLS
ATLS
ATLS
25
27
31
31
ERTH
ATLS
ATLS
ERTH
36
39
43
46
ERTH
ERTH
ERTH
ERTH
60
64
70
76
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
VENS
VENS
VENS
18
19
22
ATLS
ATLS
ATLS
27
28
35
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
54
58
64
PLRS
PLRS
PLRS
85 NEPT
100 NEPT
110 NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
VENS
ATLS
ATLS
24
28
31
ATLS
ATLS
ERTH
39
40
48
ERTH
ERTH
ERTH
48
52
66
ERTH
PLRS
PLRS
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
ERTH 54q u PLRS 85q u PLRS 105q u NEPT 160q u SATN 260 TITN 400q u JUPT 500
PLRS 70q u PLRS 90q u PLRS 120q u ORON 190 TITN 320q u TITN 440q u JUPT 600q u
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
1 7 .2 1
2 0 .4 1
2 4 .0 0
8
10
1 5 HP
254T
MERC 4
MARS 5
MARS 7
ATLS 14
MARS 10
VENS 14
2 0 HP
256T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
2 5 HP
284T
MARS 6
VENS 10
VENS 11
ATLS 18
VENS 17
VENS 22
MARS
VENS
VENS
11
15
16
VENS
VENS
VENS
17
19
22
VENS
VENS
ATLS
21
23
30
ATLS
ATLS
ATLS
26
30
38
15
17
20
26
ATLS
VENS
ATLS
ATLS
20
23
29
34
ATLS
ATLS
ATLS
ERTH
32
33
41
54
ATLS
ERTH
ERTH
ERTH
38t
46
54
66
ERTH
ERTH
ERTH
PLRS
50
58
72
90
ATLS
ATLS
ATLS
30
31
38
ATLS
ERTH
ERTH
38
44
50
ERTH
ERTH
ERTH
60
62
74
PLRS
PLRS
PLRS
80
85
100
PLRS
PLRS
PLRS
100
105
120
ERTH
ERTH
ERTH
42
46
50
NEPT
ERTH
ERTH
60
58
68
NEPT
PLRS
PLRS
90 NEPT
95 NEPT
100 NEPT
110 SATN
115 NEPT
130 NEPT
180
145
160
ERTH 74q
PLRS 80
PLRS 90q
190q
190
205
240
ORON
ORON
SATN
SATN
SATN
SATN
TITN
250
280
320
TITN
TITN
TITN
340
400
440
TITN
JUPT
JUPT
420
500
550
TITN
TITN
JUPT
350
400
450
JUPT
JUPT
JUPT
500
550
600
JUPT
JUPT
550
650
550
SATN
SATN
TITN
280
280
350
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
19
1750rR2.p65
18
Black
7/19/2002, 10:25 AM
SELECTION TABLES
1750 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
496
399
286
188
159
126
3 0 HP
286T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
4 0 HP
324T
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 34
5 0 HP
326T
VENS 12
VENS 14
ATLS 18
ERTH 32
ATLS 36
ERTH 46
1 5 0 HP
200
445T
PLRS 42
NEPT 55 NEPT
NEPT 90
NEPT 100 ORON
ORON 135 SATN
1 7 .2 1
2 0 .4 1
2 4 .0 0
102
86
86
73
73
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
ERTH
ERTH
PLRS
52
58
80
ERTH
ERTH
PLRS
64
70
90
SATN
SATN
TITN
160
190
230
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
ERTH
ERTH
PLRS
PLRS
56 PLRS
70 PLRS
85 PLRS
100 NEPT
80t NEPT
90 PLRS
115 NEPT
140 ORON
100
110
140
180
NEPT
NEPT
ORON
ORON
120 NEPT
130 ORON
175 ORON
210 SATN
140t SATN
170 SATN
200 TITN
255 TITN
200
220
300
360
TITN
TITN
TITN
JUPT
280
280
340
450
TITN
TITN
JUPT
JUPT
280
360
500
450
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
PLRS
NEPT
NEPT
TITN
TITN
TITN
300
320
350
TITN
JUPT
JUPT
380
450
500
JUPT
JUPT
JUPT
500
500
600
JUPT
JUPT
600
600
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
JUPT
TITN
TITN
300
300
320
JUPT
JUPT
JUPT
400
450
500
JUPT
550
JUPT
650
JUPT
650
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
TITN
TITN
TITN
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
JUPT
JUPT
JUPT
550
600
650
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
JUPT
650
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
46
46
60
440q
500 JUPT
600
600
JUPT
TITN
TITN
350
380
400
PLRS
PLRS
NEPT
HP
2 5 0 HP
75
SATN
100
140
175
TITN
220
TITN
TITN
TITN
240
240
310
TITN
JUPT
JUPT
280
300
400
JUPT
JUPT
JUPT
JUPT
400
450
500
600
JUPT
450
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
20
1750rR2.p65
19
Black
7/19/2002, 10:26 AM
SELECTION TABLES
1750 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
102
86
86
73
73
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
4
6
7
MERC
MARS
MARS
6
8
10
MARS
MARS
MARS
9
12
14
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
MERC
MERC
MERC
MERC
4
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MARS 7
MARS 9
MARS 10d
MARS 11
MARS
MARS
MARS
VENS
11
13
16
20
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
MERC
MERC
MERC
6
5
6
MERC
MERC
MARS
8
7
9
MARS
MARS
MARS
9
11
11
MARS
MARS
MARS
15
15
17
VENS
ATLS
ATLS
22
27
30
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
MERC
MERC
MERC
8
7
8
MARS
MARS
MARS
11
11
13
MARS
MARS
MARS
13
15
17
ATLS
VENS
VENS
22
21
22
ATLS
ATLS
ATLS
34
36
38
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
MARS
MARS
MARS
9q
11
11
ERTH 26q
ATLS 31
ATLS 35q
ERTH 44q
ERTH 46
ERTH 50q
ERTH 62q
ERTH 70
ERTH 74q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
MARS
MARS
MARS
VENS
15
13
17
18
VENS
VENS
VENS
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
31
35
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH 64q
ERTH 70
ERTH 76
PLRS 90
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
VENS
VENS
VENS
20
23
24
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
54
64
75
PLRS
PLRS
PLRS
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
496
399
286
188
159
126
1 7 .2 1
2 0 .4 1
2 4 .0 0
8
10
1 5 HP
254T
MERC 4
MARS 5
MARS 7
ATLS 14
VENS 13
VENS 16
2 0 HP
256T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 17
VENS 20
2 5 HP
284T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
MARS
VENS
VENS
13
15
18
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ERTH
30
34
42
17
19
24
30
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
62t
64
85
100
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
90
95
110
PLRS
NEPT
NEPT
110
125
140
ERTH
ERTH
ERTH
48
52
56
NEPT
ERTH
ERTH
70
70
74
NEPT
PLRS
PLRS
100 NEPT
105 NEPT
110 NEPT
TITN
TITN
TITN
TITN
320q
360
400
440
SATN
TITN
TITN
280
320
360
TITN
TITN
JUPT
380
440
500
JUPT
JUPT
JUPT
500
550
600
TITN
TITN
JUPT
430
440
500
JUPT
JUPT
550
600
JUPT
650
650
280
320
390
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
21
1750rR2.p65
20
Black
7/19/2002, 10:26 AM
SELECTION TABLES
1750 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
496
399
286
188
159
126
3 0 HP
286T
MARS 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
4 0 HP
324T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
5 0 HP
326T
VENS 12
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
1 5 0 HP
200
445T
PLRS 52
NEPT 65 NEPT
NEPT 100
ORON 125 TITN
ORON 150 SATN
1 7 .2 1
2 0 .4 1
2 4 .0 0
102
86
86
73
73
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
52
58
66
ERTH
ERTH
PLRS
58
70
90
PLRS
PLRS
NEPT
SATN
SATN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
55
55
48
48
40
40
32
32
ERTH
PLRS
PLRS
PLRS
66t NEPT
80 PLRS
95 NEPT
120 ORON
100
100
130
180
NEPT
NEPT
ORON
ORON
170
185
230
320
TITN
SATN
TITN
TITN
280
250
340
400
TITN
TITN
TITN
JUPT
6 4 .4 2
6 9 .6 3
8 0 .0 1
27
27
25
25
22
22
NEPT
NEPT
NEPT
JUPT
JUPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 9 .1
1 7 .6
1 5 .7
SATN 210
ORON 215
ORON 220
SATN
SATN
SATN
260
265
300
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 4 .4
1 2 .6
1 1 .0
SATN 240q
SATN 280
SATN 300q
TITN
TITN
TITN
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
9 .1
8 .5
7 .3
6 .6
TITN 400q
TITN 440 JUPT
JUPT 550 JUPT
JUPT 550
2 9 5 .7
3 3 0 .1
3 6 9 .8
5 .9
5 .3
4 .7
JUPT
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
4 .2
3 .8
3 .3
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .8
2 .6
2 .4
9 0 0 .3
1057
1 .9
1 .7
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
75 NEPT
80 PLRS
105 NEPT
SATN
SATN
TITN
255
280
350
TITN
TITN
TITN
340
360
430
JUPT
JUPT
JUPT
450
450
550
JUPT
TITN
TITN
400
420
440
JUPT
450
JUPT
600
JUPT
550
550
JUPT
650
JUPT
TITN
TITN
300
340
400
HP
2 5 0 HP
85
SATN
120
210
190
TITN
260
240
280
350
TITN
JUPT
JUPT
320
350
450
280
320
380
450
500
550
550
JUPT
190
210
270
TITN
TITN
TITN
650
650
550
650
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1750rR2.p65
22
21
Black
7/19/2002, 10:27 AM
SELECTION TABLES
1430 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
1 5 HP
254T
MERC 4
MERC 4
MARS 5
2 0 HP
256T
MERC 4
MARS 5
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
5
6
MERC
MERC
5
6
MARS
MARS
8
10
MARS
MARS
10
12
2 5 HP
284T
MARS 6
MARS 7
MARS 7
ATLS 14
VENS 13
VENS 16
83
83
70
70
60
60
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
4
6
7
MERC
MARS
MARS
6
8
8
MARS
MARS
MARS
9
10
12
MARS
VENS
VENS
11
15
16
VENS
VENS
VENS
15
17
20
VENS
VENS
ATLS
19
21
26
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
4
5
7
8
MARS 7
MARS 9
MARS 10d
MARS 11
MARS
MARS
MARS
MARS
11
13
14
17
MARS
VENS
VENS
VENS
13
17
20
24
ATLS
VENS
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ATLS
ERTH
28
33
41
48
ATLS
ATLS
ERTH
ERTH
34t
41
48
60
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
MERC
MERC
MERC
4
3
4
MERC
MERC
MERC
6
5
6
MERC
MERC
MERC
6
7
8
MARS
MARS
MARS
9
9
11
MARS
MARS
MARS
15
15
17
VENS
VENS
ATLS
20
22
26
ATLS
ATLS
ATLS
26
31
34
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
54
62
68
ERTH
PLRS
PLRS
66
75
90
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
13
13
15
ATLS
VENS
VENS
22
21
24
ATLS
ATLS
ATLS
30
32
34
ERTH
ATLS
ERTH
42
40
50
NEPT
ERTH
ERTH
60
64
68
NEPT
PLRS
PLRS
80
85
90
NEPT
PLRS
PLRS
100
105
120
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
MERC
MERC
MERC
5q
7
8
MARS
MARS
MARS
9q
9
11
ATLS
ATLS
ATLS
26q
31
35q
ATLS 38q
ATLS 43q
ERTH 50q
ERTH 50q
ERTH 58
ERTH 62q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
MARS
MERC
MARS
MARS
9
8
11
13
MARS
MARS
MARS
MARS
13
13
15
17
VENS
MARS
VENS
VENS
16
17
20
22
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ERTH
ATLS
ERTH
ERTH
42
43
52
52
ERTH
ERTH
ERTH
PLRS
60
64
70
80
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
MARS
MARS
MARS
13
14
16
VENS
VENS
VENS
18
21
22
VENS
ATLS
ATLS
24
28
31
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
60
70
76
PLRS
PLRS
PLRS
95 PLRS
100 NEPT
110 NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
MARS
VENS
VENS
18
19
22
ATLS
ATLS
ATLS
27
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
58
72
PLRS
PLRS
PLRS
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
ATLS
ERTH
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
36
48
ERTH 74q
PLRS 90
PLRS 90q
150q
190
205
215
ORON
ORON
SATN
SATN
190q
215
240
270
TITN
TITN
TITN
300
360
400
TITN
TITN
JUPT
350
360
450
TITN
JUPT
JUPT
430
450
550
550
550
JUPT
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
23
1430rR2p65.p65
22
Black
7/19/2002, 11:26 AM
SELECTION TABLES
1430 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
286T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
4 0 HP
324T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
5 0 HP
326T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
83
83
70
70
60
60
ATLS
ATLS
ATLS
22
26
30
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
46
52
60
ERTH
ERTH
PLRS
58
64
80
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ERTH
ERTH
PLRS
PLRS
56
64
75
100
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
80t
90
115
140
NEPT
NEPT
NEPT
ORON
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
PLRS
PLRS
PLRS
80 PLRS
95 NEPT
100 NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
NEPT
NEPT
NEPT
1 2 1 .4
1 3 8 .5
1 5 9 .8
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
PLRS
PLRS
NEPT
75 NEPT
80 PLRS
105 NEPT
1 5 0 HP
445T
PLRS 34
PLRS 32
NEPT 45
PLRS 64
POLR 70
NEPT 95
170
200
245
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
320
380
450
TITN 360
JUPT 400d
JUPT 500
JUPT 550
JUPT
JUPT
JUPT
550
550
650
JUPT
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
420
450
500
JUPT
TITN
JUPT
400
420
450
JUPT
500
JUPT
550
JUPT
600
1 1 .8
1 0 .3
8 .9
NEPT 150q ORON 205q SATN 260q SATN 300q TITN 400q JUPT
ORON 190 ORON 240 SATN 280 TITN 340 TITN 420
ORON 190q ORON 240q SATN 300q TITN 360q JUPT 500 JUPT
550
JUPT
650
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
ORON
SATN
SATN
TITN
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
TITN
TITN
TITN
380
400
440
JUPT
JUPT
JUPT
500
550
600
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
JUPT
JUPT
JUPT
500
550
650
JUPT
600
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
JUPT
JUPT
JUPT
JUPT
500
550
600
650
JUPT
2 5 0 HP
42
55 NEPT 65
80
270
320
350
300
300
360
PLRS
NEPT
NEPT
NEPT
NEPT
SATN
TITN
TITN
JUPT
TITN
TITN
2 0 0 HP
190
210
270
650
650
650
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1430rR2p65.p65
24
23
Black
7/19/2002, 11:26 AM
SELECTION TABLES
1430 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
1 5 HP
254T
MERC 4
MERC 4
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
83
83
70
70
60
60
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MARS
MARS
MARS
7
10
10
MARS
MARS
MARS
11
12
14
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
3
5d
6
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MARS
6
7
7
9
MARS
MARS
MARS
MARS
9
11
12
15
MARS
MARS
VENS
VENS
13
15
18
22
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
17
18
22
ATLS
ATLS
ATLS
26
27
34
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
MERC
MERC
MERC
6
7
6
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
15
17
18
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ATLS
38
40
42
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
MERC
MARS
MARS
7q
9
9
ATLS
ATLS
ATLS
30q
35
43q
ERTH 50q
ERTH 52
ERTH 62q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
MARS
MARS
MARS
MARS
11
11
13
15
VENS
MARS
VENS
VENS
16
15
18
20
VENS
VENS
VENS
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
35
39
43
ERTH
ERTH
ERTH
ERTH
54
58
58
70
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
MARS
MARS
VENS
17
18
20
VENS
ATLS
ATLS
24
28
31
ATLS
ATLS
ATLS
31
36
39
ERTH
ERTH
ERTH
48
52
58
ERTH
PLRS
PLRS
72 PLRS
90 PLRS
100 NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
9 0 0 .3
1057
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
10
12
2 0 HP
256T
MARS 6
MARS 7
MARS 7
ATLS 14
VENS 13
VENS 16
2 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
VENS
VENS
VENS
15
15
20
VENS
VENS
VENS
19
21
26
ATLS
ATLS
ATLS
26
26
34
19
19
24
30
ATLS
ATLS
ATLS
ERTH
28
29
37
48
ATLS
ATLS
ERTH
ERTH
34t
41
48
60
ERTH
ERTH
ERTH
ERTH
44
52
60
72
ATLS
ATLS
ATLS
34
39
42
ERTH
ERTH
ERTH
54
56
62
ERTH
ERTH
PLRS
66
75
90
PLRS
PLRS
PLRS
90
95
110
ERTH
ERTH
ERTH
48
52
56
NEPT
PLRS
PLRS
80
75
90
PLRS
PLRS
PLRS
100 NEPT
105 NEPT
120 NEPT
120
125
140
ERTH 62q
ERTH 70
PLRS 80q
190q ORON
215 SATN
240 SATN
270 TITN
240q
270
300
360
TITN
TITN
TITN
300
360
400
TITN
TITN
JUPT
380
440
500
TITN
JUPT
JUPT
430
450
550
JUPT
JUPT
JUPT
500
600
650
2 .3
2 .2
1 .9
ATLS 32 ERTH 52 ERTH 64 PLRS 100 NEPT 160 ORON 240 TITN 320 JUPT 500 JUPT
ERTH 36q u ERTH 54q u PLRS 70q u PLRS 100q u ORON 190 SATN 240q u TITN 320q u JUPT 500
ATLS 39 ERTH 60 PLRS 85 NEPT 125 ORON 215 TITN 310 TITN 390 JUPT 550q u
650
1 .6
1 .4
ERTH 48q u PLRS 75q u PLRS 95q u NEPT 140q u ORON 215
ERTH 60 PLRS 80q u PLRS 110q u ORON 190 SATN 260
310
360
430
ORON
ORON
SATN
SATN
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
25
1430rR2p65.p65
24
Black
7/19/2002, 11:27 AM
SELECTION TABLES
1430 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
286T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 19
VENS 22
4 0 HP
324T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
5 0 HP
326T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
83
83
70
70
60
60
ATLS
ATLS
ATLS
30
30
38
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
58
64
80
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 NEPT
120 NEPT
80t
100
120
150
NEPT
NEPT
NEPT
ORON
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
PLRS
NEPT
PLRS
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
SATN
SATN
SATN
240
250
300
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
TITN
TITN
TITN
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
JUPT
JUPT
JUPT
450
500
550
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
JUPT
600
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
JUPT
JUPT
PLRS
PLRS
NEPT
75
80
95
NEPT
PLRS
NEPT
170
200
245
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
320
380
450
JUPT
JUPT
JUPT
500
500
650
JUPT
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
420
450
550
JUPT
TITN
TITN
350
380
440
JUPT
500
JUPT
600
JUPT
600
500
JUPT
650
550
650
650
JUPT
2 5 0 HP
52
65 NEPT 85
100
120 TITN 210
150 SATN 190
SATN
SATN
TITN
255
280
300
300
300
360
HP
SATN
SATN
SATN
JUPT
TITN
TITN
1 5 0 HP
200
445T
PLRS 34
PLRS 42 PLRS
NEPT 55 NEPT
NEPT 80 NEPT
NEPT 90 ORON
NEPT 115 ORON
190
210
270
TITN
TITN
TITN
240
280
310
650
600
650
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
26
1430rR2p65.p65
25
Black
7/19/2002, 11:27 AM
SELECTION TABLES
1430 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
1 5 HP
254T
MERC 4
MARS 5
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
5
6
MERC
MARS
5
8
MARS
MARS
8
10
MARS
VENS
83
83
70
70
60
60
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
3
MERC
MERC
MERC
4
4
5
MERC
MARS
MARS
6
8
8
MARS
MARS
MARS
9
10
12
MARS
VENS
VENS
11
15
16
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
4
5
5d
8
MERC
MERC
MARS
MARS
6
7
8d
11
MARS
MARS
MARS
MARS
9
11
14
17
VENS
VENS
VENS
ATLS
15
17
20
26
ATLS
VENS
ATLS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
13
13
15
VENS
VENS
VENS
20
20
24
ATLS
ATLS
ATLS
30
31
34
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
MERC
MERC
MERC
6
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
11
13
15
MARS
VENS
VENS
17
17
20
ATLS
ATLS
ATLS
30
28
34
ERTH
ERTH
ERTH
42
46
50
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
MERC
MARS
MARS
7q
9
11
ATLS 34q
ATLS 39
ERTH 44q
ERTH 56q
ERTH 64
ERTH 68q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
MARS
MARS
MARS
MARS
13
13
15
15
VENS
MARS
VENS
VENS
18
17
20
22
ATLS
VENS
ATLS
ATLS
25
24
27
31
ATLS
ATLS
ATLS
ERTH
33
39
43
46
ERTH
ERTH
ERTH
ERTH
60
64
70
76
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
VENS
VENS
VENS
18
19
22
ATLS
ATLS
ATLS
27
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
58
64
PLRS
PLRS
PLRS
85
90
110
NEPT
NEPT
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
VENS
ATLS
ATLS
24
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
52
66
ERTH
ERTH
PLRS
72
76
95
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
10
14
2 0 HP
256T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 13
VENS 18
2 5 HP
284T
MARS 6
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 22
VENS
VENS
VENS
15
17
22
VENS
VENS
ATLS
21
23
30
ATLS
ATLS
ATLS
26
30
38
20
21
29
34
ATLS
ATLS
ATLS
ERTH
32
33
41
54
ATLS
ERTH
ERTH
ERTH
38t
46
54
66
ERTH
ERTH
ERTH
PLRS
50
58
66
90
ATLS
ERTH
ERTH
38
44
50
ERTH
ERTH
ERTH
60
62
68
PLRS
PLRS
PLRS
80
85
90
PLRS
PLRS
PLRS
100
105
120
ERTH
ERTH
ERTH
54
58
68
NEPT
PLRS
PLRS
90 NEPT
85 NEPT
100 NEPT
110 SATN
115 NEPT
130 NEPT
180
145
160
ERTH 68q
PLRS 80
PLRS 90q
160q
190
205
240
350
400
450
550
550
ERTH 54q u PLRS 85q u PLRS 105q u NEPT 150q u ORON 240
PLRS 70q u PLRS 90q u PLRS 120q u ORON 190 SATN 280
ORON
ORON
SATN
SATN
TITN
TITN
TITN
340
360
440
TITN
JUPT
JUPT
420
500
550
JUPT
JUPT
JUPT
500
550
600
JUPT
JUPT
650
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
27
1430rR2p65.p65
26
Black
7/19/2002, 11:28 AM
SELECTION TABLES
1430 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
286T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
4 0 HP
324T
VENS 10
VENS 10
VENS 15
ATLS 26
ATLS 28
ATLS 34
5 0 HP
326T
VENS 10
VENS 14
ATLS 18
ERTH 32
ATLS 36
ERTH 46
83
83
70
70
60
60
ATLS
ATLS
ERTH
30
34
42
ERTH
ERTH
ERTH
ERTH
ERTH
PLRS
52
58
70
ERTH
ERTH
PLRS
64
70
90
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
ERTH
ERTH
PLRS
PLRS
62t PLRS
64 PLRS
85 PLRS
100 NEPT
80t NEPT
90 PLRS
105 NEPT
130 ORON
100
110
130
180
NEPT
NEPT
ORON
ORON
120 NEPT
130 ORON
175 ORON
195 SATN
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
PLRS
NEPT
NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
SATN
SATN
TITN
260
280
320
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
TITN
TITN
TITN
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
TITN
TITN
TITN
TITN
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
JUPT
JUPT
JUPT
500
550
650
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
40
46
60
2 5 0 HP
52
75
SATN
100
140
175
TITN
TITN
210
220
200
240
310
TITN
TITN
TITN
TITN
TITN
TITN
280
280
350
140t SATN
170 SATN
200 SATN
255 TITN
200
220
260
360
TITN
TITN
TITN
JUPT
280
280
340
450
TITN
TITN
JUPT
JUPT
280
320
500
450
450
TITN
TITN
TITN
300
320
350
TITN
TITN
JUPT
380
400
450
JUPT
JUPT
JUPT
500
500
600
JUPT
JUPT
550
600
JUPT
TITN
JUPT
400
420
500
JUPT
550
JUPT
650
JUPT
650
550
JUPT
TITN
TITN
350
340
400
PLRS
PLRS
NEPT
HP
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1430rR2p65.p65
28
27
Black
7/19/2002, 11:28 AM
SELECTION TABLES
1430 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
5
6
MERC
MARS
5
8
MARS
MARS
83
83
70
70
60
60
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
4
6
5
MERC
MARS
MARS
6
8
8
MARS
MARS
MARS
9
12
12
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
4
5
7
8
MERC
MARS
MARS
MARS
6
9
8d
11
MARS
MARS
MARS
MARS
11
13
14
17
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
MERC
MERC
MERC
6
5
6
MERC
MERC
MERC
8
7
8
MARS
MARS
MARS
9
9
11
MARS
MARS
MARS
13
13
15
VENS
VENS
ATLS
20
22
26
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
MERC
MERC
MERC
6
7
8
MARS
MARS
MARS
9
11
11
MARS
MARS
MARS
13
13
15
MARS
VENS
VENS
17
19
20
ATLS
ATLS
ATLS
30
32
34
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
MARS
MARS
MARS
9q
9
11
ATLS
ATLS
ATLS
22q
27
31q
ATLS 38q
ATLS 43q
ERTH 50q
ERTH 56q
ERTH 64
ERTH 70q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
MARS
MARS
MARS
MARS
13
13
15
17
VENS
VENS
VENS
VENS
18
20
22
24
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ERTH
ATLS
ATLS
ERTH
36
39
43
52
ERTH
ERTH
ERTH
ERTH
60
64
70
80
ORON
ORON
ORON
ORON
190q ORON
190 SATN
230 SATN
240 TITN
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
VENS
VENS
VENS
18
21
22
ATLS
ATLS
ATLS
27
32
35
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
54
58
70
PLRS
PLRS
PLRS
SATN
SATN
TITN
280
300
360
TITN
TITN
TITN
380
400
440
JUPT
JUPT
JUPT
450
500
550
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
ATLS
ATLS
ATLS
27
28
31
ATLS
ERTH
ERTH
39
46
54
ERTH
ERTH
ERTH
48
58
72
ERTH
PLRS
PLRS
TITN
TITN
JUPT
390
440
500
JUPT
JUPT
JUPT
500
550
650
JUPT
600
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
600
9 0 0 .3
1057
1 .6
1 .4
ERTH 54q u PLRS 85q u PLRS 115q u SATN 180q u SATN 270q u TITN 440q u JUPT 550
ORON 190 PLRS 100q u NEPT 130 ORON 190 TITN 360q u JUPT 500q u JUPT 650q u
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
8
10
1 5 HP
254T
MERC 4
MARS 5
MARS 7
ATLS 14
MARS 10
VENS 14
2 0 HP
256T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
2 5 HP
284T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 19
VENS 22
MARS
VENS
VENS
11
15
16
ATLS
VENS
ATLS
17
19
26
ATLS
ATLS
ATLS
22
26
30
ATLS
ATLS
ATLS
30
30
38
17
17
22
26
ATLS
VENS
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ERTH
ERTH
32
37
42
54
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ERTH
ERTH
ERTH
PLRS
50
58
72
90
ATLS
ATLS
ATLS
30
35
38
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
60
68
74
PLRS
PLRS
PLRS
80 PLRS
95 NEPT
100 PLRS
100
115
120
ERTH
ERTH
ERTH
48
46
56
NEPT
ERTH
ERTH
60
64
68
NEPT
PLRS
PLRS
90
95
110
NEPT
NEPT
NEPT
ERTH 74q
PLRS 90
PLRS 90q
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
29
1430rR2p65.p65
28
Black
7/19/2002, 11:29 AM
SELECTION TABLES
1430 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
286T
MARS 8
VENS 10
VENS 13
ATLS 18
VENS 21
ATLS 26
4 0 HP
324T
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 38
5 0 HP
326T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
83
83
70
70
60
60
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
46
52
60
ERTH
ERTH
PLRS
58
64
80
ERTH
PLRS
PLRS
64
80
90
PLRS
PLRS
NEPT
SATN
SATN
TITN
160
190
230
TITN
TITN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
ERTH
ERTH
PLRS
PLRS
60t
70
85
110
PLRS
PLRS
PLRS
NEPT
80t
90
115
140
NEPT
NEPT
NEPT
ORON
110
120
140
180
NEPT
NEPT
ORON
ORON
120t
140
175
210
NEPT
ORON
ORON
SATN
150t SATN
170 SATN
225 TITN
270 TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
280
380
450
TITN
TITN
JUPT
JUPT
320
360
500
500
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
PLRS
NEPT
NEPT
SATN
SATN
SATN
240
260
300
TITN
TITN
TITN
300
320
390
TITN
JUPT
JUPT
420
450
500
JUPT
JUPT
JUPT
500
500
650
JUPT
JUPT
600
600
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
JUPT
TITN
TITN
350
380
440
JUPT
JUPT
JUPT
450
500
550
JUPT
550
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
TITN 360q
TITN 400
TITN 440
JUPT 500
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
JUPT
JUPT
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
JUPT
JUPT
JUPT
JUPT
500
550
600
650
JUPT
TITN
TITN
JUPT
300
300
360
2 0 0 HP
NEPT 60
NEPT 75
ORON 140
ORON 140
SATN 175
2 5 0 HP
SATN
100
TITN
TITN
210
220
TiTN
JUPT
JUPT
280
300
400
450
240
240
310
650
550
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
30
1430rR2p65.p65
29
Black
7/19/2002, 11:30 AM
SELECTION TABLES
1430 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 1
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
83
83
70
70
60
60
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
4
6
7
MARS
MARS
MARS
7
8
10
MARS
MARS
MARS
11
12
14
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
MERC
MERC
MERC
MERC
2
3
5d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MARS 7
MARS 9
MARS 10d
MARS 13
MARS
MARS
VENS
VENS
13
15
18
20
VENS
VENS
ATLS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
MERC
MERC
MERC
6
5
6
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
MARS
VENS
15
15
18
VENS
ATLS
ATLS
24
27
30
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
MARS
MARS
13
15
17
ATLS
VENS
VENS
22
21
24
ATLS
ATLS
ATLS
34
36
42
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
MARS
MARS
MARS
9q
9
11
ATLS
ATLS
ATLS
26q
31
39q
ERTH 44q
ERTH 52
ERTH 56q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
MARS
MARS
VENS
VENS
15
15
18
20
ATLS
VENS
ATLS
ATLS
21
24
27
31
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
42
46
52
58
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
60
70
76
PLRS
PLRS
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
43
52
60
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
8
12
1 5 HP
254T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 13
VENS 16
2 0 HP
256T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 17
VENS 20
2 5 HP
284T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
MARS
VENS
VENS
13
15
18
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
38
ATLS
ATLS
ERTH
34
38
48
19
21
25
34
ATLS
ATLS
ATLS
ATLS
28
29
33
42
ATLS
ATLS
ERTH
ERTH
34t
41
54
66
ERTH
ERTH
ERTH
PLRS
50
58
66
80
ERTH
ERTH
PLRS
PLRS
60t
70
85
100
ATLS
ATLS
ATLS
34
39
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
72
75
90
PLRS
PLRS
PLRS
100 PLRS
105 NEPT
120 NEPT
120
125
140
ERTH
ERTH
ERTH
54
52
62
NEPT
ERTH
PLRS
70
70
80
NEPT
PLRS
PLRS
110 SATN
105 NEPT
120 NEPT
ERTH 68q
PLRS 80
PLRS 80q
280
320
390
ORON
ORON
SATN
SATN
TITN
TITN
TITN
300
360
400
TITN
JUPT
JUPT
420
450
550
JUPT
JUPT
JUPT
550
500
550
JUPT
JUPT
550
650
JUPT
JUPT
JUPT
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
31
1430rR2p65.p65
30
Black
7/19/2002, 11:30 AM
550
600
650
SELECTION TABLES
1430 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
286T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 28
ATLS 30
4 0 HP
324T
VENS 10
VENS 14
ATLS 18
ERTH 32
ATLS 36
ERTH 40
5 0 HP
326T
VENS 14
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
83
83
70
70
60
60
ATLS
ERTH
ERTH
38
46
54
ERTH
ERTH
PLRS
52
58
70
ERTH
ERTH
PLRS
64
70
90
PLRS
PLRS
NEPT
75 NEPT
90 NEPT
105 NEPT
SATN
SATN
TITN
170
190
230
SATN
SATN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
PLRS
PLRS
PLRS
PLRS
70t NEPT
80 PLRS
105 NEPT
120 ORON
100
110
130
180
NEPT
NEPT
ORON
ORON
130t
140
175
210
NEPT
ORON
ORON
SATN
140t ORON
170 ORON
200 SATN
255 TITN
170
200
245
320
TITN
TITN
TITN
JUPT
280
280
340
400
TITN
TITN
JUPT
JUPT
320
360
500
500
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
TITN
TITN
TITN
300
320
350
TITN
TITN
TITN
340
400
430
JUPT
JUPT
JUPT
500
500
600
JUPT
JUPT
600
600
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
SATN 210
ORON 215
SATN 240
SATN
SATN
TITN
260
280
320
JUPT
TITN
JUPT
400
420
500
JUPT
500
JUPT
650
JUPT
600
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
SATN 260q
TITN 300
TITN 320q
TITN
TITN
TITN
550
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
TITN 400q
TITN 440 JUPT
JUPT 550
JUPT 550
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
JUPT
TITN
TITN
350
380
400
HP
2 5 0 HP
60
100
SATN
120
165
220
TITN
TITN
210
260
TITN
TITN
TITN
280
280
350
TiTN
JUPT
320
350
450
190
210
270
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
32
1430rR2p65.p65
31
Black
7/19/2002, 11:30 AM
SELECTION TABLES
1430 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
3
4
1 5 HP
254T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
2 0 HP
256T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
2 5 HP
284T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MARS
MARS
MARS
9
10
12
MARS
VENS
VENS
11
15
16
VENS
VENS
VENS
15
17
20
ATLS
ATLS
ATLS
22
26
30
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
40
54
4
5
7
8
MERC
MERC
MARS
MARS
6
7
8d
9
MARS
MARS
MARS
MARS
9
11
12
13
MARS
VENS
VENS
VENS
13
17
20
24
ATLS
VENS
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ATLS
ERTH
28
33
41
48
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ERTH
ERTH
PLRS
PLRS
56
64
75
100
PLRS
PLRS
PLRS
PLRS
70t
80
95
120
MARS
MARS
MARS
9
9
11
MARS
MARS
MARS
11
13
15
MARS
VENS
VENS
17
18
20
ATLS
ATLS
ATLS
26
31
34
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
54
62
68
PLRS
PLRS
PLRS
80 PLRS
95 NEPT
100 NEPT
MARS
MARS
MARS
13
13
15
MARS
VENS
VENS
15
17
18
ATLS
ATLS
ATLS
26
24
30
ERTH
ATLS
ERTH
42
40
50
NEPT
ERTH
ERTH
60
64
68
NEPT
PLRS
PLRS
80
85
90
NEPT
NEPT
NEPT
1 1 .8
1 0 .3
8 .9
ATLS
ATLS
ATLS
30q
35
43q
ERTH 50q
ERTH 58
ERTH 62q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
VENS
MARS
VENS
VENS
16
17
20
22
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ATLS
ATLS
ATLS
ATLS
33
35
39
43
ERTH
ERTH
ERTH
ERTH
48
52
58
64
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
VENS
ATLS
ATLS
24
28
31
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
48
52
58
ERTH
PLRS
PLRS
72
80
90
PLRS
NEPT
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
58
72
ERTH
ERTH
PLRS
66
76
95
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
1 HP
143T
MERC 2
MERC 2
MERC 1
1 .5 HP
145T
MERC 2
MERC 2
MERC 1
2 HP
145T
MERC 2
MERC 2
MERC 3
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
83
83
70
70
60
60
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
5
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
MERC
MERC
MERC
6
7
8
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
MERC
MARS
MARS
8
9
11
1 2 1 .4
1 3 8 .5
1 5 9 .8
ERTH 74q
PLRS 90
PLRS 90q
160q ORON
190 SATN
205 SATN
215 TITN
350
360
450
550
550
TITN
TITN
TITN
380
400
440
JUPT
JUPT
JUPT
500
550
600
JUPT
JUPT
JUPT
450
550
650
JUPT
600
JUPT
JUPT
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
33
1430rR2p65.p65
32
Black
7/19/2002, 11:31 AM
600
650
SELECTION TABLES
1430 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
405
326
234
154
130
103
1 7 .2 1
2 0 .4 1
2 4 .0 0
3 0 HP
286T
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 38
4 0 HP
324T
VENS 12
VENS 16
ATLS 22
ERTH 32
ERTH 42
ERTH 46
5 0 HP
326T
VENS 16
ATLS 20
ATLS 26
ERTH 44
ERTH 48
ERTH 58
83
83
70
70
60
60
ERTH
ERTH
ERTH
46
52
60
ERTH
ERTH
PLRS
58
64
80
PLRS
PLRS
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
45
45
39
39
33
33
26
26
NEPT
PLRS
PLRS
NEPT
90
90
115
140
NEPT
NEPT
NEPT
ORON
6 4 .4 2
6 9 .6 3
8 0 .0 1
22
22
21
21
1 7 .9
SATN
TITN
TITN
270
320
350
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 5 .6
1 4 .4
1 2 .9
SATN 240
ORON 240
SATN 270
JUPT
TITN
JUPT
1 2 1 .4
1 3 8 .5
1 5 9 .8
1 1 .8
1 0 .3
8 .9
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
7 .4
6 .9
6 .0
5 .4
JUPT
JUPT
JUPT
JUPT
2 9 5 .7
3 3 0 .1
3 6 9 .8
4 .8
4 .3
3 .9
4 1 2 .1
4 5 9 .0
5 3 2 .5
3 .5
3 .1
2 .7
6 1 7 .9
6 6 0 .6
7 4 1 .2
2 .3
2 .2
1 .9
9 0 0 .3
1057
1 .6
1 .4
JUPT
TITN
TITN
300
340
360
75 NEPT
80 PLRS
105 NEPT
190
210
270
TITN
TITN
TITN
240
240
310
HP
2 5 0 HP
80 ORON 90
100 SATN 140
210
260
TITN
JUPT
250
300
JUPT
400
SATN
SATN
TITN
TITN
JUPT
JUPT
320
350
450
155
185
225
280
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
320
380
450
500
TITN
TITN
TITN
340
360
390
TITN
JUPT
JUPT
420
450
500
JUPT
JUPT
JUPT
550
550
650
JUPT
400
420
450
JUPT
JUPT
JUPT
450
500
550
JUPT
550
550
JUPT
650
650
650
500
550
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1430rR2p65.p65
34
33
Black
7/19/2002, 11:31 AM
SELECTION TABLES
1170 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
continued
1 .5 HP
182T
MERC 2
MERC 2
MERC 1
2 HP
184T
MERC 2
MERC 2
MERC 1
3 HP
213T
MERC 2
MERC 2
MERC 3
5 HP
215T
MERC 2
MERC 2
MERC 3
7 .5 HP
254T
MERC 2
MERC 2
MERC 3
1 0 HP
256T
MERC 2
MERC 4
MARS 5
1 5 HP
284T
MERC 4
MERC 4
MARS 7
MERC
MERC
1
2
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
68
68
57
57
49
49
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MARS
MARS
MARS
7
10
10
MARS
MARS
MARS
9
12
14
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
MERC
MERC
MERC
MERC
2
3
3d
4
MERC
MERC
MERC
MERC
4
3
5d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MARS
MARS
MARS
MARS
9
11
12
15
MARS
MARS
VENS
VENS
13
15
18
22
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
MERC
MERC
MERC
4
5
6
MERC
MERC
MERC
6
7
8
MERC
MERC
MARS
8
7
9
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
17
18
20
VENS
ATLS
ATLS
24
27
30
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
MERC
MERC
MERC
6
7
6
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
15
17
18
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ATLS
38
40
42
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
MERC
MARS
MERC
7q
9
8
MARS
MARS
MARS
9q
11
13
ATLS
ATLS
ATLS
30q
35
43q
ERTH 50q
ERTH 52
ERTH 56q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
MARS
MARS
MARS
MARS
11
11
13
13
MARS
MARS
VENS
VENS
15
15
18
20
VENS
VENS
VENS
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
48
52
58
64
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
MARS
MARS
VENS
15
18
20
VENS
ATLS
ATLS
22
24
27
ATLS
ATLS
ATLS
31
32
39
ERTH
ERTH
ERTH
48
52
58
ERTH
PLRS
PLRS
72
80
90
PLRS
PLRS
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
9 0 0 .3
1057
8
12
2 0 HP
286T
MERC 4
MARS 5
MARS 7
ATLS 14
VENS 13
VENS 14
2 5 HP
324T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 18
VENS
VENS
VENS
15
15
20
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
22
26
34
17
19
24
30
ATLS
ATLS
ATLS
ERTH
28
29
37
48
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
56
62
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
80
95
100
ERTH
ERTH
ERTH
48
52
56
NEPT
PLRS
PLRS
80
75
90
NEPT
PLRS
PLRS
100 NEPT
105 NEPT
110 NEPT
120
125
140
ERTH 62q
ERTH 70
ERTH 74q
ORON
ORON
SATN
SATN
190q ORON
230 SATN
240 SATN
270 TITN
240q
270
300
320
SATN
TITN
TITN
280
320
360
TITN
TITN
JUPT
380
400
450
TITN
TITN
JUPT
390
440
500
JUPT
JUPT
JUPT
550
550
650
1 .9
1 .8
1 .6
ATLS 32 ERTH 46 ERTH 64 PLRS 100 NEPT 160 ORON 240 TITN 320 JUPT 500 JUPT
ERTH 36q u ERTH 54q u PLRS 70q u PLRS 100q u NEPT 160q u SATN 240q u TITN 320q u JUPT 500
ATLS 35 ERTH 60 PLRS 85 PLRS 115 ORON 190 TITN 310 TITN 390 JUPT 550q u
650
1 .3
1 .1
ERTH 48q u PLRS 75q u PLRS 95q u NEPT 140q u ORON 215
ERTH 54 PLRS 80q u PLRS 100q u ORON 190 SATN 260
TITN
TITN
TITN
310
360
430
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
35
1170rR2.p65
34
Black
7/19/2002, 10:05 AM
SELECTION TABLES
1170 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e d u c t io n
S in g le
D o u b le
Tr i p l e
Q u a d r u p le
N o m i n a l A p p ro x .
O u t pu t
R a t io
RPM
M o t o r H o r s e p o w e r & Fr a m e S i z e
3 0 HP
326T
MARS 6
VENS 10
VENS 11
ATLS 18
VENS 17
VENS 22
4 0 HP
364T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
5 0 HP
365T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
6 0 HP
404T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
7 5 HP
405T
VENS 14
ATLS 20
ATLS 26
ERTH 38
ERTH 48
ERTH 58
1 0 0 HP
444T
ERTH 18
ATLS 24
ERTH 34
ERTH 50
ERTH 60
PLRS 75
ERTH
ERTH
ERTH
ERTH
ERTH
PLRS
PLRS
PLRS
NEPT
NEPT
PLRS
NEPT
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
68
6
8
57
57
49
49
ATLS
ATLS
ATLS
30
30
38
ATLS
ERTH
ERTH
38
40
54
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
3
7
32
32
26
26
21
21
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
PLRS
PLRS
PLRS
100 NEPT
105 NEPT
120 NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
1 2 1 .4
1 3 8 .5
1 5 9 .8
46
52
66
80t NEPT
100 PLRS
115 NEPT
150 ORON
58
64
80
SATN
SATN
TITN
240
280
310
170
185
230
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
280
340
450
JUPT
JUPT
JUPT
500
500
600
JUPT
240
280
300
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
420
450
500
JUPT
600
300
300
360
JUPT
TITN
TITN
350
380
440
JUPT
450
JUPT
550
9 .6
8 .4
7 .3
TITN
TITN
TITN
360q JUPT
420
440q JUPT
500
JUPT
650
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
JUPT
650
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
TITN
JUPT
JUPT
420
500
550
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
JUPT
550
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
500
550
600
650
34
38
46
80
90
105
2 5 0 HP
SATN
SATN
SATN
PLRS
ERTH
ERTH
NEPT
PLRS
NEPT
2 0 0 HP
150
175
JUPT
TITN
TITN
JUPT
JUPT
JUPT
JUPT
1 5 0 HP
PLRS 44 SATN
PLRS 52 NEPT
NEPT 65 NEPT
NEPT 100
ORON 125 SATN
ORON 150 SATN
240
250
300
JUPT
JUPT
SATN
SATN
SATN
75
80
95
1 2 5 HP
445T
PLRS 34
ATLS 28
ERTH 40
PLRS 64
PLRS 80
NEPT 95
175
210
270
TITN
TITN
TITN
60
60
85
650
600
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1170rR2.p65
36
35
Black
7/19/2002, 10:05 AM
SELECTION TABLES
1170 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
continued
4 0 HP
364T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
5 0 HP
365T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
6 0 HP
404T
VENS 14
ATLS 20
ATLS 26
ERTH 38
ERTH 48
ERTH 58
7 5 HP
405T
ERTH 18
ATLS 24
ATLS 30
ERTH 50
ERTH 54
PLRS 75
68
68
57
57
49
49
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
58
64
80
PLRS
PLRS
NEPT
PLRS
PLRS
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
ERTH
ERTH
PLRS
PLRS
62t
70
85
110
PLRS
PLRS
PLRS
NEPT
80t
100
115
150
NEPT
NEPT
NEPT
ORON
NEPT
ORON
ORON
SATN
150t SATN
185 SATN
225 TITN
270 TITN
220
235
300
360
TITN
TITN
TITN
JUPT
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
PLRS
NEPT
NEPT
JUPT
JUPT
JUPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
SATN 180
ORON 190
ORON 230
1 2 1 .4
1 3 8 .5
1 5 9 .8
75
80
95
1 0 0 HP
444T
ERTH 24
ATLS 28
ERTH 40
PLRS 64
PLRS 80
NEPT 95
SATN
SATN
SATN
240
280
300
TITN
TITN
TITN
300
360
390
TITN
JUPT
JUPT
420
450
500
JUPT
TITN
TITN
350
380
440
JUPT
JUPT
JUPT
450
500
550
JUPT
600
9 .6
8 .4
7 .3
500
JUPT
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
TITN 360q
TITN 400
TITN 440
JUPT 500
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
JUPT
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
SATN
SATN
SATN
JUPT
JUPT
JUPT
JUPT
240
250
300
500
550
600
650
JUPT
TITN
TITN
JUPT
300
340
360
1 2 5 HP
150
445T
PLRS 34 PLRS
ERTH 38 ERTH
NEPT 55 NEPT
NEPT 80 NEPT
NEPT 90 NEPT
NEPT 115 ORON
HP
2 0 0 HP
2 5 0 HP
34 PLRS
44 NEPT
65 NEPT
100
110 SATN
135 SATN
44
60
85
SATN
NEPT
SATN
60
70
100
150
175
SATN
TITN
180
220
SATN
SATN
TITN
175
190
230
TITN
TITN
TITN
240
280
310
TITN
JUPT
JUPT
280
350
400
280
320
380
450
TITN
TITN
JUPT
JUPT
320
360
500
500
500
500
550
650
JUPT
JUPT
600
640
600
650
550
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
37
1170rR2.p65
36
Black
7/19/2002, 10:06 AM
SELECTION TABLES
1170 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
326T
MARS 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
4 0 HP
364T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
5 0 HP
365T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
68
68
57
57
49
49
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
58
64
80
PLRS
PLRS
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
ERTH
ERTH
PLRS
PLRS
62t
70
85
110
PLRS
PLRS
PLRS
NEPT
80t
100
115
150
NEPT
NEPT
NEPT
ORON
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
PLRS
NEPT
NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
SATN 180
ORON 190
ORON 230
1 2 1 .4
1 3 8 .5
1 5 9 .8
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
75
80
95
180
220
240
280
310
280
350
400
NEPT
ORON
ORON
SATN
150t SATN
185 SATN
225 TITN
270 TITN
220
235
300
360
TITN
TITN
TITN
JUPT
280
320
380
450
TITN
TITN
JUPT
JUPT
320
360
500
500
500
JUPT
JUPT
JUPT
500
550
650
JUPT
JUPT
600
640
JUPT
TITN
TITN
350
380
440
JUPT
JUPT
JUPT
450
500
550
JUPT
600
9 .6
8 .4
7 .3
500
JUPT
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
TITN 360q
TITN 400
TITN 440
JUPT 500
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
JUPT
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
JUPT
SATN
TITN
TITN
JUPT
JUPT
420
450
500
500
550
600
650
150
175
TITN
TITN
TITN
TITN
JUPT
JUPT
JUPT
JUPT
JUPT
JUPT
60
70
100
175
190
230
300
360
390
300
340
360
SATN
NEPT
SATN
SATN
SATN
TITN
TITN
TITN
TITN
JUPT
TITN
TITN
2 5 0 HP
44
60
85
240
280
300
240
250
300
2 0 0 HP
34 PLRS
44 NEPT
65 NEPT
100
110 SATN
135 SATN
PLRS
PLRS
NEPT
SATN
SATN
SATN
SATN
SATN
SATN
HP
600
650
550
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
38
1170rR2.p65
37
Black
7/19/2002, 10:06 AM
SELECTION TABLES
1170 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
continued
1 .5 HP
182T
MERC 2
MERC 2
MERC 1
2 HP
184T
MERC 2
MERC 2
MERC 1
3 HP
213T
MERC 2
MERC 2
MERC 3
5 HP
215T
MERC 2
MERC 2
MERC 3
7 .5 HP
254T
MERC 4
MERC 4
MARS 5
1 0 HP
256T
MERC 4
MERC 4
MARS 5
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
3
4
MERC
MERC
5
6
MARS
MARS
6
8
MARS
MARS
68
68
57
57
49
49
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MARS
4
6
7
MARS
MARS
MARS
7
8
10
MARS
MARS
MARS
11
12
14
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
MERC
MERC
MERC
MERC
4
3
5d
4
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MARS 7
MARS 9
MARS 10d
MARS 13
MARS
MARS
MARS
VENS
11
15
16
20
VENS
VENS
VENS
ATLS
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
MERC
MERC
MERC
6
5
6
MERC
MARS
MARS
8
9
9
MARS
MARS
MARS
11
11
13
MARS
MARS
VENS
15
15
18
VENS
ATLS
ATLS
24
27
30
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
MERC
MARS
MERC
8
9
8
MARS
MARS
MARS
11
11
13
MARS
MARS
MARS
13
15
17
ATLS
VENS
VENS
22
21
24
ATLS
ATLS
ATLS
34
36
42
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
MARS
MARS
MARS
9q
11
13
ATLS
ATLS
ATLS
26q
31
35q
ERTH 44q
ERTH 52
ERTH 56q
ERTH 68q
PLRS 80
PLRS 80q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
MARS
MARS
MARS
VENS
15
15
17
18
VENS
VENS
ATLS
ATLS
20
22
27
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
42
46
52
58
ERTH 64q
ERTH 76
PLRS 80
PLRS 90
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
VENS
VENS
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
60
70
76
PLRS
PLRS
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
ATLS
ATLS
ATLS
31
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
PLRS
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
8
12
1 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 13
VENS 16
2 0 HP
286T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 17
VENS 20
2 5 HP
324T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
MARS
VENS
VENS
13
15
18
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ERTH
34
38
48
19
21
24
30
ATLS
ATLS
ATLS
ATLS
24
29
33
42
ATLS
ATLS
ERTH
ERTH
34t
41
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
62t
64
85
100
ATLS
ATLS
ATLAS
34
39
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
72
75
90
PLRS
PLRS
PLRS
90 PLRS
105 NEPT
110 NEPT
120
125
140
ERTH
ERTH
ERTH
54
52
62
NEPT
ERTH
PLRS
70
70
80
NEPT
PLRS
PLRS
100 SATN
105 NEPT
120 NEPT
ORON
ORON
SATN
SATN
TITN
TITN
TITN
300
360
400
TITN
TITN
JUPT
420
440
500
JUPT
JUPT
JUPT
500
600
650
TITN
JUPT
JUPT
430
500
550
JUPT
JUPT
550
650
JUPT
650
650
SATN
TITN
TITN
280
320
390
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
39
1170rR2.p65
38
Black
7/19/2002, 10:07 AM
SELECTION TABLES
1170 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
326T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
4 0 HP
364T
VENS 10
VENS 14
VENS 17
ERTH 32
ATLS 32
ERTH 40
5 0 HP
365T
VENS 14
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
68
68
57
57
49
49
ATLS
ERTH
ERTH
38
46
54
ERTH
ERTH
PLRS
52
58
70
ERTH
ERTH
PLRS
64
70
90
PLRS
PLRS
NEPT
75 NEPT
90 NEPT
105 NEPT
SATN
SATN
TITN
160
190
230
SATN
SATN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
ERTH
PLRS
PLRS
PLRS
66t NEPT
80 PLRS
105 NEPT
120 ORON
100
110
130
180
NEPT
NEPT
ORON
ORON
120 NEPT
130 ORON
175 ORON
210 SATN
140t ORON
170 ORON
200 SATN
240 TITN
170
200
245
320
TITN
TITN
TITN
TITN
280
280
340
400
TITN
TITN
JUPT
JUPT
280
320
500
450
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
SATN
TITN
TITN
270
320
350
TITN
TITN
TITN
340
400
430
JUPT
JUPT
JUPT
450
500
550
JUPT
JUPT
600
600
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
SATN 210
ORON 215
SATN 240
SATN
SATN
TITN
260
280
320
JUPT
TITN
JUPT
400
420
500
JUPT
500
JUPT
650
JUPT
600
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
SATN 260q
TITN 300
TITN 320q
TITN
TITN
TITN
550
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
TITN 400q
TITN 440 JUPT
JUPT 550
JUPT 550
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
JUPT
TITN
TITN
350
340
400
1 5 0 HP
190
210
270
2 0 0 HP
TITN
TITN
TITN
280
280
350
2 5 0 HP
TITN
JUPT
JUPT
320
350
450
650
600
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1170rR2.p65
40
39
Black
7/19/2002, 10:07 AM
SELECTION TABLES
1170 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
3
4
1 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 13
VENS 16
2 0 HP
286T
MARS 6
VENS 10
VENS 11
ATLS 18
VENS 17
VENS 22
2 5 HP
324T
MARS 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
MERC
MARS
MARS
8
9
11
MARS
MARS
MARS
8
9
9
MARS
MARS
MARS
11
13
13
MARS
VENS
MARS
MARS
MARS
MARS
6 .1
5 .7
4 .9
4 .4
2 9 5 .7
3 3 0 .1
3 6 9 .8
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
1 HP
145T
MERC 2
MERC 2
MERC 1
1 .5 HP
182T
MERC 2
MERC 2
MERC 1
2 HP
184T
MERC 2
MERC 2
MERC 3
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
68
68
57
57
49
49
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
3
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
MERC
MERC
MERC
MERC
4
3
5d
4
MERC
MERC
MERC
MERC
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
MERC
MERC
MERC
6
7
8
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
MERC
MARS
MARS
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6
6
7
MARS
MARS
MARS
7
10
10
MARS
VENS
MARS
11
15
14
VENS
VENS
VENS
15
15
20
VENS
VENS
ATLS
21
23
30
ATLS
ATLS
ATLS
30
30
38
ATLS
ATLS
ERTH
34
38
48
MARS 7
MARS 9
MARS 10d
MARS 13
MARS
MARS
VENS
VENS
13
15
18
22
VENS
VENS
ATLS
ATLS
19
21
29
34
ATLS
ATLS
ATLS
ATLS
28
29
37
42
ATLS
ATLS
ERTH
ERTH
38t
41
54
66
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
ERTH
PLRS
PLRS
62t
70
85
110
11
11
13
MARS
MARS
VENS
15
17
18
VENS
ATLS
ATLS
24
27
30
ATLS
ATLS
ERTH
38
39
50
ERTH
ERTH
ERTH
48
56
62
ERTH
PLRS
PLRS
72
85
90
PLRS
PLRS
PLRS
100 PLRS
105 NEPT
120 NEPT
120
135
150
15
17
17
ATLS
VENS
ATLS
22
23
26
ATLS
ATLS
ATLS
38
40
42
ERTH
ERTH
ERTH
54
58
62
NEPT
PLRS
PLRS
80
75
90
NEPT
NEPT
NEPT
9q
11
13
ATLS
ATLS
ATLS
26q
31
39q
ERTH 50q
ERTH 52
ERTH 56q
MARS
MARS
VENS
VENS
15
15
18
20
ATLS
VENS
ATLS
ATLS
25
24
27
31
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
48
46
52
58
4
3 .5
3 .2
VENS
ATLS
ATLS
22
24
27
ATLS
ATLS
ATLS
35
36
43
ATLS
ERTH
ERTH
43
52
58
ERTH
ERTH
PLRS
66
76
80
PLRS
PLRS
NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
ATLS
ATLS
ATLS
31
36
39
ERTH
ERTH
ERTH
48
52
66
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
ERTH 46 ERTH 70 PLRS 100 NEPT 140 ORON 240 TITN 360 JUPT 500
ERTH 54q u PLRS 80q u PLRS 100q u NEPT 150q u SATN 240q u TITN 360q u JUPT 500
ERTH 60 PLRS 95 PLRS 115 ORON 190 TITN 310 TITN 430 JUPT 550q u
9 0 0 .3
1057
1 .3
1 .1
ERTH 68q
PLRS 80
PLRS 90q
140q
160
180
190
ORON
ORON
SATN
SATN
310
360
430
TITN
TITN
TITN
340
360
400
TITN
JUPT
JUPT
440
500
550
JUPT
JUPT
JUPT
500
500
600
JUPT
550
JUPT
JUPT
550
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
41
1170rR2.p65
40
Black
7/19/2002, 10:08 AM
SELECTION TABLES
1170 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
326T
VENS 10
VENS 10
VENS 15
ATLS 22
ATLS 28
ATLS 34
4 0 HP
364T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
5 0 HP
365T
VENS 14
ATLS 20
ATLS 26
ERTH 38
ERTH 48
ERTH 58
68
68
57
57
49
49
ERTH
ERTH
ERTH
ERTH
ERTH
PLRS
PLRS
PLRS
NEPT
PLRS
PLRS
NEPT
SATN
SATN
TITN
175
190
230
TITN
TITN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
NEPT
ORON
ORON
SATN
150t SATN
170 SATN
225 SATN
255 TITN
200
220
260
320
TITN
TITN
TITN
JUPT
280
280
340
450
TITN
TITN
JUPT
JUPT
320
360
500
500
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
SATN
SATN
SATN
240
280
300
TITN
TITN
TITN
300
320
390
TITN
TITN
JUPT
380
400
450
JUPT
JUPT
JUPT
500
500
600
JUPT
JUPT
600
640
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
SATN 240
ORON 240
SATN 270
JUPT
TITN
TITN
300
300
360
JUPT
TITN
TITN
350
380
440
JUPT
JUPT
JUPT
400
500
500
JUPT
500
JUPT
650
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
SATN 280q
TITN 340
TITN 360q
TITN
TITN
TITN
360q JUPT
420
440q JUPT
500
JUPT
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
TITN
JUPT
JUPT
JUPT
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
JUPT 650
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
40
46
60
440q
500 JUPT
550
600
58
64
80
75
80
95
HP
2 5 0 HP
60
70
100
SATN
SATN
SATN
80
90
120
180
220
TITN
JUPT
250
300
TITN
JUPT
JUPT
280
300
400
JUPT
400
450
200
240
310
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
42
1170rR2.p65
41
Black
7/19/2002, 10:08 AM
SELECTION TABLES
1170 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
continued
3
4
1 5 HP
284T
MARS 6
MARS 7
VENS 11
ATLS 14
VENS 15
VENS 20
2 0 HP
286T
MARS 8
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
2 5 HP
324T
VENS 10
VENS 10
VENS 15
ATLS 22
ATLS 28
ATLS 34
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
6
6
7
MARS
MARS
MARS
9
10
12
MARS
VENS
VENS
13
15
16
VENS
VENS
VENS
17
19
22
ATLS
ATLS
ATLS
26
26
34
ATLS
ATLS
ERTH
34
38
48
ATLS
ERTH
ERTH
38
46
54
6
7
7
8
MERC
MERC
MARS
MARS
6
7
8d
11
MARS
MARS
MARS
MARS
9
11
12
15
VENS
VENS
VENS
ATLS
15
17
20
26
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ATLS
ERTH
32
33
41
54
ERTH
ERTH
ERTH
PLRS
50
52
60
80
ERTH
ERTH
PLRS
PLRS
62t PLRS
64 PLRS
85 PLRS
100 NEPT
70t
80
105
130
MARS
MARS
MARS
9
11
11
MARS
MARS
MARS
13
13
15
VENS
VENS
VENS
18
20
22
ATLS
ATLS
ATLS
30
31
38
ATLS
ERTH
ERTH
42
50
56
ERTH
ERTH
ERTH
60
62
74
PLRS
PLRS
PLRS
90
95
110
PLRS
NEPT
NEPT
MARS
MARS
MARS
13
15
15
MARS
VENS
VENS
17
17
20
ATLS
ATLS
ATLS
26
28
30
ERTH
ERTH
ERTH
42
46
50
NEPT
ERTH
ERTH
70
64
74
NEPT
PLRS
PLRS
90 NEPT
85 NEPT
100 NEPT
1 HP
145T
MERC 2
MERC 2
MERC 1
1 .5 HP
182T
MERC 2
MERC 2
MERC 1
2 HP
184T
MERC 2
MERC 2
MERC 3
MERC
MERC
1
2
MERC
MERC
3
2
MERC
MERC
68
68
57
57
49
49
MERC
MERC
MERC
2
2
3
MERC
MERC
MERC
4
4
5
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
MERC
MERC
MERC
6
7
8
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
MERC
MARS
MARS
8
9
11
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
ATLS 34q
ATLS 39
ERTH 44q
ERTH 56q
ERTH 64
ERTH 68q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
VENS
MARS
VENS
VENS
18
17
22
24
ATLS
ATLS
ATLS
ATLS
25
31
31
35
ATLS
ATLS
ATLS
ERTH
33
39
43
46
ERTH
ERTH
ERTH
ERTH
54
58
64
70
PLRS
PLRS
PLRS
PLRS
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
ATLS
ATLS
ATLS
27
28
35
ATLS
ERTH
ERTH
39
46
52
ERTH
ERTH
ERTH
54
58
64
PLRS
PLRS
PLRS
75 NEPT
90 NEPT
100 NEPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
ATLS
ATLS
ERTH
39
40
48
ERTH
ERTH
ERTH
54
58
72
ERTH
PLRS
PLRS
72
80
95
PLRS
PLRS
NEPT
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
PLRS 80q PLRS 110q NEPT 160q ORON 230q SATN 260q
PLRS 90 NEPT 120 ORON 190 ORON 240 TITN 300
PLRS 100q NEPT 130q ORON 215q SATN 260q TITN 360q
80q PLRS
90 NEPT
100 NEPT
120 ORON
120q
140
150
190
NEPT
ORON
ORON
ORON
160q ORON
190 SATN
205 SATN
240 TITN
SATN
SATN
TITN
250
300
320
TITN
TITN
JUPT
380
440
500
JUPT
JUPT
JUPT
500
600
650
TITN
TITN
JUPT
350
400
450
JUPT
JUPT
JUPT
550
600
650
JUPT
650
550
SATN
SATN
TITN
280
300
390
JUPT
650
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
43
1170rR2.p65
42
Black
7/19/2002, 10:08 AM
SELECTION TABLES
1170 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
3 0 HP
326T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
4 0 HP
364T
VENS 14
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
5 0 HP
365T
VENS 16
ATLS 20
ATLS 30
ERTH 44
ERTH 54
ERTH 64
68
68
57
57
49
49
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
64
70
90
PLRS
PLRS
NEPT
NEPT
NEPT
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
NEPT
PLRS
NEPT
NEPT
90
100
120
150
NEPT
NEPT
ORON
ORON
120 NEPT
130 ORON
175 ORON
210 SATN
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
ORON 180
ORON 205
ORON 220
SATN
SATN
SATN
240
260
300
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
SATN
SATN
SATN
240
265
300
JUPT
TITN
TITN
350
340
400
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
85
90
115
HP
80
80
120
SATN
SATN
SATN
80
110
140
150
190
TITN
TITN
210
260
TITN
JUPT
250
300
240
280
350
TITN
JUPT
JUPT
320
350
450
JUPT
450
SATN
SATN
TITN
160
190
230
SATN
TITN
TITN
140t ORON
170 ORON
200 SATN
255 TITN
170
200
245
320
TITN
SATN
TITN
TITN
280
250
300
400
TITN
TITN
JUPT
JUPT
280
320
500
450
TITN
TITN
TITN
300
320
350
TITN
TITN
TITN
340
400
430
TITN
JUPT
JUPT
420
450
550
JUPT
JUPT
600
600
JUPT
JUPT
JUPT
400
450
500
JUPT
500
JUPT
600
JUPT
600
TITN
TITN
TITN
600
JUPT
JUPT
550
650
TITN
TITN
TITN
2 5 0 HP
SATN
NEPT
SATN
190
240
270
2 0 0 HP
54
60
85
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
44
1170rR2.p65
43
Black
7/19/2002, 10:09 AM
SELECTION TABLES
1170 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
continued
3
4
1 5 HP
284T
MARS 6
VENS 10
VENS 11
ATLS 18
VENS 17
VENS 22
2 0 HP
286T
MARS 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
2 5 HP
324T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
4
6
5
MERC
MARS
MARS
6
8
8
MARS
MARS
MARS
9
12
14
VENS
VENS
VENS
15
15
20
VENS
VENS
ATLS
19
21
26
ATLS
ATLS
ATLS
30
30
38
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
46
52
66
MARS 7
MARS 9
MARS 10d
MARS 11
MARS
MARS
MARS
MARS
11
13
14
17
VENS
VENS
VENS
ATLS
17
19
24
30
ATLS
ATLS
ATLS
ERTH
28
29
37
48
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
80t
100
115
150
11
11
13
MARS
MARS
MARS
15
15
17
VENS
VENS
VENS
20
22
24
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
56
62
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
100 NEPT
105 NEPT
120 NEPT
15
17
18
ATLS
VENS
VENS
22
21
22
ATLS
ATLS
ATLS
30
32
34
ERTH
ERTH
ERTH
48
52
56
NEPT
PLRS
PLRS
80
75
90
NEPT
PLRS
PLRS
9 .6
8 .4
7 .3
ATLS
ATLS
ATLS
26q
31
35
ATLS 38q
ATLS 43q
ERTH 44q
ERTH 62q
ERTH 70
ERTH 74q
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
VENS
VENS
VENS
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH
ERTH
ERTH
ERTH
60
64
70
76
140q
160
180
190
ORON
ORON
ORON
SATN
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
ATLS
ATLS
ATLS
31
32
39
ERTH
ERTH
ERTH
48
52
58
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
SATN
TITN
TITN
280
320
360
TITN
JUPT
JUPT
420
500
550
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
PLRS
TITN
TITN
JUPT
390
440
500
JUPT
550
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
650
9 0 0 .3
1057
1 .3
1 .1
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
1 HP
145T
MERC 2
MERC 2
MERC 1
1 .5 HP
182T
MERC 2
MERC 2
MERC 3
2 HP
184T
MERC 2
MERC 2
MERC 3
MERC
MERC
3
2
MERC
MERC
3
4
MERC
MERC
68
68
57
57
49
49
MERC
MERC
MERC
2
4
3
MERC
MERC
MERC
4
4
5
MERC
MERC
MERC
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
MERC
MERC
MERC
MERC
4
5
5d
6
MERC
MERC
MERC
MERC
6
7
7
8
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
MERC
MERC
MARS
8
7
9
MARS
MARS
MARS
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
MARS
MARS
MARS
11
11
13
MARS
VENS
VENS
1 2 1 .4
1 3 8 .5
1 5 9 .8
240
250
300
PLRS 90q PLRS 120q ORON 180q SATN 260q SATN 300q
PLRS 110 NEPT 140 ORON 215 SATN 280 TITN 340
PLRS 110q NEPT 150q ORON 240q SATN 300q TITN 400q
TITN
TITN
TITN
310
360
430
JUPT
JUPT
JUPT
JUPT
JUPT
JUPT
500
550
600
650
600
650
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
45
1170rR2.p65
44
Black
7/19/2002, 10:09 AM
SELECTION TABLES
1170 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
331
267
191
126
106
84
84
1 7 .2 1
2 0 .4 1
2 4 .0 0
3 0 HP
326T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
4 0 HP
364T
VENS 14
ATLS 20
ATLS 26
ERTH 44
ERTH 48
ERTH 58
5 0 HP
365T
ERTH 18
ATLS 24
ERTH 34
ERTH 50
ERTH 60
PLRS 75
68
68
57
57
49
49
ERTH
ERTH
PLRS
58
64
80
PLRS
PLRS
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
37
37
32
32
26
26
21
21
NEPT
PLRS
NEPT
ORON
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 8 .2
1 6 .8
1 4 .6
ORON 205
ORON 230
SATN 240
SATN
SATN
TITN
255
280
350
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 .8
1 1 .8
1 0 .5
JUPT
TITN
TITN
300
300
360
JUPT
TITN
TITN
400
420
440
1 2 1 .4
1 3 8 .5
1 5 9 .8
9 .6
8 .4
7 .3
TITN
TITN
TITN
360q JUPT
420
440q JUPT
550
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
6 .1
5 .7
4 .9
4 .4
JUPT
650
2 9 5 .7
3 3 0 .1
3 6 9 .8
4
3 .5
3 .2
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .8
2 .5
2 .2
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .9
1 .8
1 .6
9 0 0 .3
1057
1 .3
1 .1
75 NEPT
80 PLRS
105 NEPT
HP
SATN
SATN
SATN
80
90
140
180
220
TITN
JUPT
250
300
JUPT
400
SATN
SATN
TITN
TITN
JUPT
JUPT
280
300
400
170
185
230
320
SATN
SATN
TITN
TITN
220
220
300
360
TITN
TITN
TITN
JUPT
280
280
340
450
450
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
380
450
500
JUPT
JUPT
JUPT
500
500
600
JUPT
JUPT
450
JUPT
550
JUPT
550
JUPT
650
175
210
270
TITN
TITN
TITN
240
280
310
2 0 0 HP
54
70
100
2 5 0 HP
SATN
SATN
100
110
JUPT
330
650
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
1170rR2.p65
46
45
Black
7/19/2002, 10:10 AM
SELECTION TABLES
870 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
Reduction
Single
Double
Triple
Quadruple
continued
1 HP
182T
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T
M ER C 2
M ER C 2
M ER C 1
2 HP
213T
M ER C 2
M ER C 2
M ER C 1
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
5
6
M AR S
M AR S
6
8
M AR S
M AR S
51
51
43
43
36
36
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
4
6
7
M AR S
M AR S
M AR S
7
8
10
M AR S
M AR S
M AR S
11
12
14
31.63
36.56
43.78
54.45
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
4
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
VEN S
11
13
16
20
VEN S
VEN S
VEN S
ATLS
64.42
69.63
80.01
13.5
12.5
10.9
M ER C
M ER C
M ER C
6
5
6
M ER C
M AR S
M ER C
8
9
9
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
15
15
17
VEN S
ATLS
ATLS
22
27
30
91.41
99.38
111.5
9.5
8.8
7.8
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
34
36
38
121.4
138.5
159.8
7.2
6.3
5.4
M AR S
M AR S
M AR S
9q
11
11
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
4.5
4.2
3.7
3.3
M AR S
M AR S
M AR S
VEN S
15
13
17
18
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
35
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH 64q
ERTH 70
ERTH 76
PLRS 90
295.7
330.1
369.8
2.9
2.6
2.4
VEN S
VEN S
VEN S
20
23
24
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
39
46
52
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
412.1
459.0
532.5
2.1
1.9
1.6
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
54
64
75
PLRS
PLRS
PLRS
617.9
660.6
741.2
1.4
1.3
1.2
900.3
1057
0.97
0.82
PLRS 65qu PLRS 95qu NEPT 120qu ORON 190 SATN 300qu TITN 440qu JUPT
PLRS 70qu PLRS 100qu SATN 170 ORON 215 TITN 360qu JUPT 550qu
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
8
10
15 HP
286T T
M ER C 4
M AR S 5
M AR S 7
ATLS 14
VENS 13
VENS 16
20 HP
324T
M AR S 6
M AR S 7
VENS 11
ATLS 14
VENS 17
VENS 20
25 HP
326T
M AR S 8
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
M AR S
VEN S
VEN S
13
15
18
VEN S
VEN S
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ERTH
30
34
42
19
19
24
30
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
60t
64
85
100
ATLS
ATLS
ATLS
34
39
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
90 PLRS
95 NEPT
110 NEPT
110
125
140
ERTH
ERTH
ERTH
48
52
56
N EPT
ERTH
ERTH
70
70
74
N EPT
PLRS
PLRS
100 NEPT
105 NEPT
120 NEPT
130
140
160
190
O RO N
O RO N
O RO N
SATN
190q
215
230
270
SATN 260q
SATN 300
TITN 320
TITN 360
TITN 320q
TITN 360
TITN 400
TITN 440
TITN
TITN
TITN
300
320
360
TITN
TITN
JUPT
380
440
500
JUPT
JUPT
JUPT
500
550
600
TITN
JUPT
JUPT
430
450
500
JUPT
JUPT
500
600
JUPT
650
650
280
300
390
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
47
870rR2.p65
46
Black
7/19/2002, 10:31 AM
SELECTION TABLES
870 RPM - Class I - Service Factor = 1.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
246
198
142
94
94
79
79
63
63
1 7 .2 1
2 0 .4 1
2 4 .0 0
4 0 HP
365T
VENS 10
VENS 12
VENS 17
ERTH 32
ATLS 32
ATLS 38
5 0 HP
404T
VENS 12
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
6 0 HP
405T
VENS 16
ATLS 20
ATLS 26
ERTH 44
ERTH 48
ERTH 58
7 5 HP
444T
ERTH 18
ATLS 24
ERTH 34
ERTH 50
ERTH 60
PLRS 75
51
51
43
43
36
36
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
52
58
66
ERTH
ERTH
PLRS
64
70
90
PLRS
PLRS
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
28
28
24
24
20
20
16
16
ERTH
PLRS
PLRS
PLRS
66t NEPT
80 PLRS
95 NEPT
120 ORON
100
100
130
180
NEPT
NEPT
ORON
ORON
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 3 .5
1 2 .5
1 0 .9
NEPT
NEPT
NEPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
9 .5
8 .8
7 .8
SATN 210
ORON 215
SATN 240
SATN
SATN
SATN
240
265
300
1 2 1 .4
1 3 8 .5
1 5 9 .8
7 .2
6 .3
5 .4
SATN 260q
SATN 280
SATN 300q
TITN
TITN
TITN
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
4 .5
4 .2
3 .7
3 .3
TITN 400q
TITN 440 JUPT
JUPT 550 JUPT
JUPT 550
2 9 5 .7
3 3 0 .1
3 6 9 .8
2 .9
2 .6
2 .4
JUPT
JUPT
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .1
1 .9
1 .6
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .4
1 .3
1 .2
9 0 0 .3
1057
0 .9 7
0 .8 2
75 NEPT
80 PLRS
105 NEPT
1 0 0 HP
445T
ERTH 24
ERTH 32
ERTH 46
NEPT 70
PLRS 80
NEPT 95
2 5 0 HP
NEPT
NEPT
SATN
65
80
120
165
190
TITN
TITN
210
260
SATN
SATN
TITN
240
280
350
TITN
JUPT
JUPT
320
350
450
170
185
230
320
TITN
SATN
TITN
TITN
280
250
340
400
TITN
TITN
JUPT
JUPT
280
320
500
450
500
JUPT
JUPT
550
550
JUPT
TITN
TITN
TITN
340
360
430
JUPT
JUPT
JUPT
450
450
550
JUPT
TITN
JUPT
400
420
450
JUPT
450
JUPT
600
JUPT
600
550
JUPT
650
300
340
400
2 0 0 HP
54
60
85
255
320
350
ERTH 30
ERTH 38
NEPT 55
NEPT 90
NEPT 100
ORON 120
1 5 0 HP
ERTH 36 PLRS
ERTH 44 NEPT
NEPT 65 NEPT
NEPT 100
ORON 125 SATN
ORON 150 SATN
SATN
TITN
TITN
JUPT
TITN
TITN
1 2 5 HP
175
210
270
TITN
TITN
TITN
650
650
600
650
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
870rR2.p65
48
47
Black
7/19/2002, 10:31 AM
SELECTION TABLES
870 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
Reduction
Single
Double
Triple
Quadruple
continued
3
4
15 HP
286T
M AR S 6
M AR S 7
VENS 11
ATLS 14
VENS 15
VENS 18
20 HP
324T
M AR S 8
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
25 HP
326T
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
6
6
7
M AR S
M AR S
M AR S
9
10
12
M AR S
VEN S
VEN S
13
15
16
VEN S
VEN S
VEN S
15
17
22
ATLS
ATLS
ATLS
22
26
34
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
46
54
4
5
7
8
M ER C
M ER C
M AR S
M AR S
6
7
8d
9
M AR S
M AR S
M AR S
M AR S
9
11
12
15
VEN S
VEN S
VEN S
VEN S
15
17
20
24
ATLS
VEN S
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ATLS
ERTH
32
33
41
48
ERTH
ERTH
ERTH
ERTH
44
52
60
72
ERTH
ERTH
PLRS
PLRS
60t ERTH
64 PLRS
85 PLRS
100 PLRS
66t
80
105
120
M AR S
M AR S
M AR S
9
9
11
M AR S
M AR S
M AR S
13
13
15
M AR S
VEN S
VEN S
17
18
20
ATLS
ATLS
ATLS
30
31
34
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
54
62
68
PLRS
PLRS
PLRS
80 PLRS
95 NEPT
100 NEPT
M AR S
M AR S
M AR S
13
13
15
M AR S
VEN S
VEN S
17
17
20
ATLS
ATLS
ATLS
26
28
30
ERTH
ERTH
ERTH
42
46
50
N EPT
ERTH
ERTH
60
64
74
N EPT
PLRS
PLRS
80 NEPT
85 NEPT
100 NEPT
7.2
6.3
5.4
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
4.5
4.2
3.7
3.3
VEN S
M AR S
VEN S
VEN S
16
17
20
22
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ATLS
ATLS
ATLS
ATLS
33
35
39
43
ERTH
ERTH
ERTH
ERTH
48
52
58
64
295.7
330.1
369.8
2.9
2.6
2.4
ATLS
ATLS
ATLS
27
28
31
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
48
58
64
ERTH
PLRS
PLRS
72
80
90
N EPT
N EPT
N EPT
412.1
459.0
532.5
2.1
1.9
1.6
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
54
58
72
ERTH
ERTH
PLRS
66
76
95
PLRS
PLRS
N EPT
TITN
TITN
JUPT
350
400
450
617.9
660.6
741.2
1.4
1.3
1.2
ERTH 52 PLRS 80 PLRS 110 NEPT 160 SATN 270 TITN 400 JUPT
ERTH 54qu PLRS 90qu PLRS 110qu ORON 190 SATN 270qu TITN 400qu JUPT
ERTH 66 PLRS 105 NEPT 135 ORON 190 TITN 350 JUPT 450qu
550
550
900.3
1057
0.97
0.82
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
1 HP
182T
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T
M ER C 2
M ER C 2
M ER C 1
2 HP
213T
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
51
51
43
43
36
36
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
4
4
5
31.63
36.56
43.78
54.45
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
64.42
69.63
80.01
13.5
12.5
10.9
M ER C
M ER C
M ER C
6
7
8
91.41
99.38
111.5
9.5
8.8
7.8
M ER C
M AR S
M AR S
8
9
11
121.4
138.5
159.8
PLRS 80q PLRS 100q NEPT 150q ORON 205q SATN 260q
PLRS 90 NEPT 120 ORON 190 ORON 240 TITN 300
PLRS 100q NEPT 130q ORON 190q SATN 260q TITN 320q
160q
190
205
215
O RO N
SATN
SATN
JUPT
240q
270
300
320
TITN 320q
TITN 360
TITN 400
TITN 440
TITN 400q
TITN 440
JUPT 550
JUPT 550
TITN
TITN
JUPT
380
400
450
JUPT
JUPT
JUPT
500
550
600
JUPT
JUPT
JUPT
JUPT
500
600
650
JUPT
650
250
300
350
N EPT
O RO N
O RO N
O RO N
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
49
870rR2.p65
48
Black
7/19/2002, 10:32 AM
SELECTION TABLES
870 RPM - Service Factor = 1.25
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
246
198
142
94
94
79
79
63
63
1 7 .2 1
2 0 .4 1
2 4 .0 0
3 0 HP
364T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
4 0 HP
365T
VENS 12
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
5 0 HP
404T
VENS 16
ATLS 20
ATLS 26
ERTH 44
ERTH 48
ERTH 64
51
51
43
43
36
36
ERTH
ERTH
ERTH
46
52
66
ERTH
ERTH
PLRS
PLRS
PLRS
NEPT
75 NEPT
90 PLRS
105 NEPT
SATN
SATN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
28
28
24
24
20
20
16
16
PLRS
PLRS
PLRS
NEPT
80t NEPT
100 NEPT
115 ORON
150 ORON
120 NEPT
130 ORON
175 ORON
195 SATN
140t ORON
170 ORON
200 SATN
240 TITN
170
185
230
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
JUPT
JUPT
280
320
500
450
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 3 .5
1 2 .5
1 0 .9
JUPT
JUPT
550
550
9 1 .4 1
9 9 .3 8
1 1 1 .5
64
70
90
SATN
TITN
TITN
270
320
350
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
420
450
500
9 .5
8 .8
7 .8
SATN
SATN
SATN
JUPT
TITN
JUPT
400
420
500
JUPT
450
JUPT
600
JUPT
600
1 2 1 .4
1 3 8 .5
1 5 9 .8
7 .2
6 .3
5 .4
550
JUPT
650
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
4 .5
4 .2
3 .7
3 .3
JUPT
JUPT
JUPT
JUPT
2 9 5 .7
3 3 0 .1
3 6 9 .8
2 .9
2 .6
2 .4
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .1
1 .9
1 .6
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .4
1 .3
1 .2
9 0 0 .3
1057
0 .9 7
0 .8 2
240
250
300
JUPT
TITN
TITN
300
340
400
HP
1 5 0 HP
2 0 0 HP
2 5 0 HP
42 PLRS
52 NEPT
65 NEPT
110
125 SATN
150 SATN
44
60
85
NEPT
NEPT
SATN
65 NEPT 75
80 ORON 110
120 SATN 140
150
190
TITN
TITN
210
260
TITN
JUPT
250
300
190
210
270
240
280
310
TITN
JUPT
JUPT
320
350
450
JUPT
450
500
TITN
TITN
TITN
650
500
550
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
50
870rR2.p65
49
Black
7/19/2002, 10:32 AM
SELECTION TABLES
870 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
Reduction
Single
Double
Triple
Quadruple
continued
3
4
15 HP
286T
M AR S 6
M AR S 7
VENS 11
ATLS 14
VENS 17
VENS 20
20 HP
324T
M AR S 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
25 HP
326T
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 34
4
6
5
M ER C
M AR S
M AR S
6
8
8
M AR S
M AR S
M AR S
9
12
12
M AR S
VEN S
VEN S
13
15
18
VEN S
VEN S
ATLS
17
19
26
ATLS
ATLS
ATLS
26
30
38
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
46
46
60
M ER C 6
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
9
11
14
15
VEN S
VEN S
VEN S
ATLS
17
19
22
30
ATLS
ATLS
ATLS
ATLS
24
29
33
42
ATLS
ATLS
ERTH
ERTH
32
37
48
54
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
60t PLRS
70 PLRS
95 PLRS
110 NEPT
80t
90
115
140
11
11
13
M AR S
M AR S
M AR S
13
15
17
VEN S
VEN S
VEN S
18
20
24
ATLS
ATLS
ATLS
30
35
38
ERTH
ERTH
ERTH
48
50
56
ERTH
ERTH
ERTH
60
68
74
PLRS
PLRS
PLRS
90 PLRS
105 NEPT
120 NEPT
13
15
17
ATLS
VEN S
VEN S
22
19
22
ATLS
ATLS
ATLS
30
28
34
ERTH
ERTH
ERTH
48
46
56
N EPT
ERTH
PLRS
70
70
80
N EPT
PLRS
PLRS
90 SATN
95 NEPT
110 NEPT
13
15
15
M ARS 17
VENS 21
VENS 24q
ATLS
ATLS
ATLS
VEN S
VEN S
VEN S
ATLS
18
20
22
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ATLS
ERTH
ERTH
36
39
46
52
ERTH
ERTH
ERTH
ERTH
54
58
64
76
N EPT
N EPT
N EPT
O RO N
140q
150
160
190
O RO N
O RO N
O RO N
O RO N
190q
215
230
240
SATN 260q
SATN 300
TITN 320
TITN 360
TITN 360q
TITN 400
TITN 440
JUPT 500
2.9
2.6
2.4
ATLS
ATLS
ATLS
31
32
35
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
54
64
70
PLRS
PLRS
PLRS
SATN
SATN
TITN
280
300
360
TITN
TITN
JUPT
420
450
500
JUPT
JUPT
412.1
459.0
532.5
2.1
1.9
1.6
ATLS
ERTH
ERTH
39
46
54
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
PLRS
75 PLRS
90 NEPT
105 NEPT
TITN
TITN
JUPT
390
440
500
JUPT
JUPT
550
650
617.9
660.6
741.2
1.4
1.3
1.2
ERTH 58 PLRS 90 PLRS 120 ORON 190 SATN 300 TITN 440 JUPT
PLRS 70qu PLRS 100qu NEPT 130qu ORON 190 SATN 300qu JUPT 500
ERTH 72 PLRS 115 NEPT 145 ORON 215 TITN 390 JUPT 500qu
600
900.3
1057
0.97
0.82
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
1 HP
182T
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T
M ER C 2
M ER C 2
M ER C 1
2 HP
213T
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
1
2
M ER C
M ER C
3
4
M ER C
M ER C
51
51
43
43
36
36
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
31.63
36.56
43.78
54.45
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
64.42
69.63
80.01
13.5
12.5
10.9
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
91.41
99.38
111.5
9.5
8.8
7.8
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
121.4
138.5
159.8
7.2
6.3
5.4
M AR S
M AR S
M AR S
193.1
206.2
238.2
265.4
4.5
4.2
3.7
3.3
295.7
330.1
369.8
PLRS 90q
PLRS 100
PLRS 110
PLRS 120
280
320
390
TITN 440q
JUPT 500
JUPT 600
JUPT 600
550
600
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
51
870rR2.p65
50
Black
7/19/2002, 10:32 AM
SELECTION TABLES
870 RPM - Class II - Service Factor = 1.40
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
246
198
142
94
94
79
79
63
63
1 7 .2 1
2 0 .4 1
2 4 .0 0
3 0 HP
364T
VENS 10
VENS 14
ATLS 18
ERTH 32
ATLS 32
ERTH 40
4 0 HP
365T
VENS 14
ATLS 20
ATLS 26
ERTH 38
ERTH 48
ERTH 58
5 0 HP
404T
ERTH 18
ATLS 24
ATLS 30
ERTH 50
ERTH 54
PLRS 75
51
51
43
43
36
36
ERTH
ERTH
PLRS
52
58
70
PLRS
PLRS
NEPT
PLRS
PLRS
NEPT
SATN
SATN
TITN
175
190
230
TITN
TITN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
28
28
24
24
20
20
16
16
NEPT
PLRS
NEPT
ORON
NEPT
ORON
ORON
SATN
150t SATN
185 SATN
225 SATN
270 TITN
200
220
260
320
TITN
TITN
TITN
TITN
280
280
340
400
TITN
TITN
JUPT
JUPT
320
360
500
500
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 3 .5
1 2 .5
1 0 .9
JUPT
JUPT
600
640
9 1 .4 1
9 9 .3 8
1 1 1 .5
75
80
95
ORON 180
ORON 205
SATN 240
SATN
SATN
SATN
240
280
300
TITN
TITN
TITN
300
360
390
TITN
TITN
JUPT
380
400
450
JUPT
JUPT
JUPT
450
500
600
9 .5
8 .8
7 .8
SATN
SATN
TITN
260
280
320
JUPT
TITN
TITN
350
380
440
JUPT
JUPT
JUPT
450
500
550
JUPT
500
JUPT
650
JUPT
650
1 2 1 .4
1 3 8 .5
1 5 9 .8
7 .2
6 .3
5 .4
TITN
TITN
TITN
360q JUPT
420
440q JUPT
500
JUPT
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
4 .5
4 .2
3 .7
3 .3
JUPT
600
2 9 5 .7
3 3 0 .1
3 6 9 .8
2 .9
2 .6
2 .4
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .1
1 .9
1 .6
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .4
1 .3
1 .2
9 0 0 .3
1057
0 .9 7
0 .8 2
HP
1 5 0 HP
2 0 0 HP
2 5 0 HP
42
52
75
PLRS
NEPT
SATN
54 NEPT 75 ORON 85
70 ORON 90 ORON 105
100 SATN 120
140
175
SATN
TITN
165
220
TITN
JUPT
250
300
240
240
310
TITN
TITN
TITN
280
280
350
JUPT
400
JUPT
330
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
870rR2.p65
52
51
Black
7/19/2002, 10:33 AM
SELECTION TABLES
870 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
Reduction
Single
Double
Triple
Quadruple
continued
3
4
15 HP
286T
M AR S 6
VENS 10
VENS 11
ATLS 18
VENS 19
VENS 22
20 HP
324T
M AR S 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
25 HP
326T
VENS 10
VENS 12
VENS 17
ATLS 26
ATLS 32
ATLS 38
4
6
7
M ER C
M AR S
M AR S
6
8
8
M AR S
M AR S
M AR S
11
12
14
VEN S
VEN S
VEN S
15
15
20
VEN S
VEN S
ATLS
19
21
26
ATLS
ATLS
ATLS
30
30
38
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
46
52
66
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
11
13
14
17
VEN S
VEN S
VEN S
ATLS
19
19
24
30
ATLS
ATLS
ATLS
ERTH
28
29
37
48
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
PLRS
PLRS
PLRS
66t PLRS
80 PLRS
95 PLRS
120 NEPT
80t
100
115
150
11
11
13
M AR S
M AR S
M AR S
15
15
17
VEN S
VEN S
VEN S
20
22
24
ATLS
ATLS
ATLS
34
39
42
ERTH
ERTH
ERTH
48
56
62
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
100 NEPT
105 NEPT
120 NEPT
15
17
18
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
30
32
34
ERTH
ERTH
ERTH
48
52
56
N EPT
PLRS
PLRS
80
75
90
N EPT
PLRS
PLRS
13
15
17
ATLS 22q
VENS 21
ATLS 27q
ATLS
ATLS
ATLS
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
35
39
39
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH
ERTH
ERTH
PLRS
60
64
70
80
2.9
2.6
2.4
ATLS
ATLS
ATLS
31
32
39
ERTH
ERTH
ERTH
48
52
58
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
412.1
459.0
532.5
2.1
1.9
1.6
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
PLRS
617.9
660.6
741.2
1.4
1.3
1.2
900.3
1057
0.97
0.82
PLRS 95qu NEPT 140qu ORON 190 SATN 270qu TITN 440qu JUPT
PLRS 100qu ORON 190 ORON 215 SATN 300 JUPT 550qu
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
1 HP
182T
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T
M ER C 2
M ER C 2
M ER C 3
2 HP
213T
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
51
51
43
43
36
36
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
31.63
36.56
43.78
54.45
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
64.42
69.63
80.01
13.5
12.5
10.9
M ER C
M ER C
M AR S
8
7
9
M AR S
M AR S
M AR S
91.41
99.38
111.5
9.5
8.8
7.8
M AR S
M AR S
M AR S
11
11
13
M AR S
VEN S
VEN S
121.4
138.5
159.8
7.2
6.3
5.4
M AR S
M AR S
M AR S
193.1
206.2
238.2
265.4
4.5
4.2
3.7
3.3
295.7
330.1
369.8
240
250
300
PLRS 90q PLRS 120q ORON 180q SATN 240q SATN 300q
PLRS 110 NEPT 140 ORON 215 SATN 280 TITN 380
PLRS 120q NEPT 150q ORON 240q SATN 300q TITN 400q
O RO N
O RO N
O RO N
SATN
190q
215
230
270
SATN 280q
TITN 320
TITN 360
TITN 400
TITN 400q
TITN 440
JUPT 550
JUPT 550
TITN
TITN
TITN
300
320
360
JUPT
JUPT
JUPT
450
500
550
JUPT
JUPT
TITN
JUPT
JUPT
430
450
500
JUPT
550
650
TITN
TITN
TITN
140q
160
180
190
310
360
430
JUPT
JUPT
JUPT
JUPT
500
550
600
650
600
650
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
53
870rR2.p65
52
Black
7/19/2002, 10:33 AM
SELECTION TABLES
870 RPM - Service Factor = 1.50
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
246
198
142
94
94
79
79
63
63
1 7 .2 1
2 0 .4 1
2 4 .0 0
5 0 HP
404T
ERTH 18
ATLS 24
ERTH 34
ERTH 50
ERTH 60
PLRS 75
3 0 HP
364T
VENS 12
VENS 14
ATLS 22
ERTH 32
ATLS 36
ERTH 46
4 0 HP
365T
VENS 16
ATLS 20
ATLS 26
ERTH 44
ERTH 48
ERTH 58
51
51
43
43
36
36
ERTH
ERTH
PLRS
58
64
80
PLRS
PLRS
NEPT
75 NEPT
80 PLRS
105 NEPT
SATN
SATN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
28
28
24
24
20
20
16
16
NEPT
NEPT
NEPT
ORON
110 NEPT
120 NEPT
140 ORON
180 SATN
130t ORON
150 ORON
200 SATN
240 TITN
170
185
230
320
SATN
SATN
TITN
TITN
220
235
300
360
TITN
TITN
TITN
JUPT
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 3 .5
1 2 .5
1 0 .9
JUPT
JUPT
JUPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
ORON 205
ORON 230
SATN 240
SATN
TITN
TITN
255
320
350
TITN
TITN
TITN
340
360
430
TITN
JUPT
JUPT
420
450
500
9 .5
8 .8
7 .8
JUPT
TITN
TITN
JUPT
TITN
TITN
400
420
440
JUPT
450
JUPT
550
JUPT
600
1 2 1 .4
1 3 8 .5
1 5 9 .8
7 .2
6 .3
5 .4
550
JUPT
650
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
4 .5
4 .2
3 .7
3 .3
2 9 5 .7
3 3 0 .1
3 6 9 .8
2 .9
2 .6
2 .4
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .1
1 .9
1 .6
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .4
1 .3
1 .2
9 0 0 .3
1057
0 .9 7
0 .8 2
JUPT
300
300
360
HP
1 5 0 HP
2 0 0 HP
2 5 0 HP
44
60
85
PLRS
NEPT
SATN
150
190
SATN
TITN
180
220
TITN
JUPT
250
300
240
280
310
TITN
JUPT
JUPT
280
300
400
JUPT
400
280
280
380
450
450
500
500
600
JUPT
175
210
270
TITN
TITN
TITN
650
650
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
54
870rR2.p65
53
Black
7/19/2002, 10:34 AM
SELECTION TABLES
870 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
Reduction
Single
Double
Triple
Quadruple
continued
3
4
15 HP
286T
M AR S 8
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
20 HP
324T
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 34
25 HP
326T
VENS 12
VENS 14
ATLS 18
ERTH 32
ATLS 36
ERTH 46
M ER C
M ER C
M ER C
6
6
7
M AR S
M AR S
M AR S
7
8
10
M AR S
VEN S
VEN S
11
15
16
VEN S
VEN S
VEN S
17
19
22
VEN S
VEN S
ATLS
21
23
30
ATLS
ATLS
ERTH
34
38
48
ERTH
ERTH
ERTH
ERTH
ERTH
PLRS
52
58
80
6
7
8d
11
M AR S
M AR S
M AR S
M AR S
9
11
12
13
M AR S
M AR S
M AR S
VEN S
11
15
16
20
ATLS
VEN S
ATLS
ATLS
20
23
29
34
ATLS
ATLS
ATLS
ERTH
32
33
41
54
ATLS
ERTH
ERTH
ERTH
38t
46
54
72
ERTH
ERTH
PLRS
PLRS
60t PLRS
70 PLRS
85 PLRS
100 NEPT
80t NEPT
90 PLRS
115 NEPT
140 ORON
100
110
140
180
M AR S
M AR S
M AR S
13
13
15
M AR S
M AR S
VEN S
17
17
20
VEN S
ATLS
ATLS
24
27
30
ATLS
ERTH
ERTH
38
44
50
ERTH
ERTH
ERTH
60
62
74
PLRS
PLRS
PLRS
80 PLRS
85 NEPT
100 NEPT
M AR S
VEN S
VEN S
17
19
20
ATLS
VEN S
ATLS
26
23
26
ATLS
ATLS
ATLS
34
36
42
N EPT
ERTH
ERTH
60
58
68
N EPT
PLRS
PLRS
90 NEPT
95 NEPT
100 NEPT
7.2
6.3
5.4
ATLS
ATLS
ATLS
PLRS 110q NEPT 140q ORON 230q SATN 300q TITN 360q
NEPT 120 ORON 190 ORON 240 TITN 340 TITN 420
NEPT 130q ORON 190q SATN 260q TITN 360q TITN 440q
193.1
206.2
238.2
265.4
4.5
4.2
3.7
3.3
ATLS
ATLS
ATLS
ATLS
25
27
31
31
ERTH
ATLS
ATLS
ERTH
36
39
43
46
ERTH
ERTH
ERTH
ERTH
48
52
58
64
ERTH 70q
ERTH 76
PLRS 80
PLRS 90
O RO N
O RO N
O RO N
O RO N
190q
190
205
240
O RO N
SATN
SATN
SATN
215q
270
270
300
TITN 360q
TITN 400
TITN 400
JUPT 450
295.7
330.1
369.8
2.9
2.6
2.4
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
54
58
64
ERTH
ERTH
PLRS
66
76
90
PLRS
PLRS
N EPT
250
300
320
TITN
TITN
TITN
340
400
440
JUPT
JUPT
JUPT
550
600
650
412.1
459.0
532.5
2.1
1.9
1.6
ERTH
ERTH
ERTH
48
52
66
ERTH
PLRS
PLRS
72 PLRS
80 PLRS
105 NEPT
TITN
TITN
JUPT
350
400
450
JUPT
JUPT
JUPT
500
550
600
JUPT
650
617.9
660.6
741.2
1.4
1.3
1.2
550
900.3
1057
0.97
0.82
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
1 HP
182T
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T
M ER C 2
M ER C 2
M ER C 3
2 HP
213T
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
51
51
43
43
36
36
M ER C
M ER C
M ER C
4
4
3
M ER C
M ER C
M ER C
4
4
5
31.63
36.56
43.78
54.45
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
4
5
7
8
M ER C
M ER C
M AR S
M AR S
64.42
69.63
80.01
13.5
12.5
10.9
M ER C
M AR S
M AR S
8
9
11
91.41
99.38
111.5
9.5
8.8
7.8
M AR S
M AR S
M AR S
11
13
15
121.4
138.5
159.8
PLRS 110q
PLRS 120
NEPT 140
NEPT 150
46
46
60
JUPT
TITN
TITN
TITN 440q
JUPT 500 JUPT
JUPT 600
JUPT 600
300
300
360
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
55
870rR2.p65
54
Black
7/19/2002, 10:34 AM
SELECTION TABLES
870 RPM - Service Factor = 1.75
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
246
198
142
94
94
79
79
63
63
1 7 .2 1
2 0 .4 1
2 4 .0 0
3 0 HP
364T
VENS 14
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
4 0 HP
365T
ERTH 18
ATLS 24
ATLS 30
ERTH 50
ERTH 54
PLRS 75
51
51
43
43
36
36
ERTH
ERTH
PLRS
64
70
90
PLRS
PLRS
NEPT
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
28
28
24
24
20
20
16
16
NEPT
NEPT
ORON
ORON
120 NEPT
130 ORON
175 ORON
210 SATN
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 3 .5
1 2 .5
1 0 .9
9 1 .4 1
9 9 .3 8
1 1 1 .5
5 0 HP
404T
ERTH 24
ATLS 28
ERTH 40
PLRS 64
PLRS 70
PLRS 85
180
220
TITN
TITN
210
260
TITN
JUPT
JUPT
320
350
450
160
190
230
TITN
TITN
TITN
TITN
JUPT
JUPT
280
300
400
150t SATN
185 SATN
225 TITN
270 TITN
200
220
300
360
TITN
TITN
TITN
TITN
280
280
340
400
TITN
TITN
JUPT
JUPT
280
360
500
500
450
JUPT
JUPT
600
600
300
360
390
TITN
JUPT
JUPT
380
450
500
JUPT
JUPT
JUPT
450
500
600
9 .5
8 .8
7 .8
JUPT
TITN
TITN
350
380
400
JUPT
JUPT
JUPT
450
500
550
JUPT
550
JUPT
650
JUPT
650
1 2 1 .4
1 3 8 .5
1 5 9 .8
7 .2
6 .3
5 .4
TITN
JUPT
JUPT
440
500
550
JUPT
600
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
4 .5
4 .2
3 .7
3 .3
2 9 5 .7
3 3 0 .1
3 6 9 .8
2 .9
2 .6
2 .4
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .1
1 .9
1 .6
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .4
1 .3
1 .2
9 0 0 .3
1057
0 .9 7
0 .8 2
2 0 0 HP
65 ORON 85
80 ORON 105
120
SATN
SATN
TITN
TITN
TITN
TITN
1 5 0 HP
54 NEPT
70 NEPT
100 SATN
ORON 230
SATN 260
SATN 300
240
240
310
HP
JUPT
2 5 0 HP
SATN
SATN
120
130
330
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
t = triple reduction
q = quadruple reduction
56
870rR2.p65
55
Black
7/19/2002, 10:34 AM
SELECTION TABLES
870 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
Reduction
Single
Double
Triple
Quadruple
continued
3
4
15 HP
286T
M AR S 8
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
20 HP
324T
VENS 10
VENS 12
VENS 17
ERTH 32
ATLS 32
ATLS 38
25 HP
326T
VENS 12
VENS 16
ATLS 22
ERTH 38
ERTH 42
ERTH 52
M ER C
M ER C
M ER C
6
6
7
M AR S
M AR S
M AR S
9
10
12
M AR S
VEN S
VEN S
13
15
18
VEN S
VEN S
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
52
58
66
ERTH
ERTH
PLRS
64
70
90
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
9
11
14
15
M AR S
VEN S
VEN S
VEN S
13
17
20
24
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
PLRS
PLRS
PLRS
66t NEPT
80 PLRS
95 NEPT
120 ORON
100
100
130
180
N EPT
N EPT
O RO N
O RO N
120
130
175
195
9
11
11
M AR S
M AR S
M AR S
15
15
17
VEN S
VEN S
VEN S
18
20
22
ATLS
ATLS
ATLS
26
31
34
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
90 NEPT
95 NEPT
110 NEPT
13
15
17
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ERTH
38
40
50
N EPT
ERTH
ERTH
70
70
74
N EPT
PLRS
PLRS
100 NEPT
105 NEPT
120 NEPT
7.2
6.3
5.4
M ARS 17
VENS 19
VENS 24q
ATLS
ATLS
ATLS
PLRS 80q PLRS 120q NEPT 160q SATN 240q TITN 320q TITN 400q
PLRS 100 NEPT 140 ORON 190 SATN 280 TITN 380 JUPT 500
PLRS 100q NEPT 150q ORON 215q SATN 300q TITN 400q JUPT 550
193.1
206.2
238.2
265.4
4.5
4.2
3.7
3.3
ATLS
ATLS
ATLS
ATLS
29
31
35
35
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH
ERTH
ERTH
ERTH
54
58
64
70
N EPT
N EPT
N EPT
O RO N
295.7
330.1
369.8
2.9
2.6
2.4
ATLS
ERTH
ERTH
39
46
52
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
85 PLRS
90 NEPT
100 NEPT
412.1
459.0
532.5
2.1
1.9
1.6
ERTH
ERTH
PLRS
54
64
75
PLRS
PLRS
PLRS
85 PLRS
90 PLRS
115 NEPT
617.9
660.6
741.2
900.3
1057
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
1 HP
182T
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T
M ER C 2
M ER C 2
M ER C 3
2 HP
213T
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
51
51
43
43
36
36
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
4
6
7
31.63
36.56
43.78
54.45
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
6
7
7
8
64.42
69.63
80.01
13.5
12.5
10.9
M AR S
M AR S
M AR S
91.41
99.38
111.5
9.5
8.8
7.8
M AR S
M AR S
M AR S
121.4
138.5
159.8
ERTH 76q
PLRS 90
PLRS 100
PLRS 110
130
140
160
190
SATN
SATN
SATN
O RO N
O RO N
O RO N
SATN
215q
215
230
270
SATN 260q
SATN 300
TITN 320
TITN 360
TITN 400q
TITN 440 JUPT
JUPT 550 JUPT
JUPT 550
TITN
TITN
TITN
300
320
360
TITN
TITN
JUPT
380
440
500
JUPT
JUPT
TITN
JUPT
JUPT
430
450
500
JUPT
JUPT
500
600
1.4
1.3
1.2
PLRS 90 NEPT 130 ORON 190 SATN 270 TITN 440 JUPT
PLRS 90qu NEPT 130qu ORON 190 SATN 270qu TITN 440qu
PLRS 105 NEPT 155 ORON 215 TITN 310 JUPT 500qu
650
0.97
0.82
280
300
390
260
265
300
JUPT
TITN
TITN
300
340
400
600
650
600
650
600
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
57
870rR2.p65
56
Black
7/19/2002, 10:35 AM
SELECTION TABLES
870 RPM - Class III - Service Factor = 2.00
TABLE 3
REDUCERS WITH STANDARD INPUT SHAFT*
LOW SPEED SHAFT TORQUE RATING (1000 lb-in)
(Horizontal Mounting)
R e duc tion
Single
Double
Triple
Qua druple
Nomina l
R a tio
A pprox.
O u t pu t
R PM
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
246
198
142
94
94
79
79
63
63
1 7 .2 1
2 0 .4 1
2 4 .0 0
51
51
43
43
36
36
PLRS
PLRS
NEPT
75 NEPT
80 NEPT
105 NEPT
SATN
SATN
TITN
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
28
28
24
24
20
20
16
16
NEPT
NEPT
ORON
SATN
130t ORON
150 ORON
200 SATN
240 TITN
170
200
245
320
TITN
SATN
TITN
TITN
280
250
340
400
TITN
TITN
TITN
JUPT
6 4 .4 2
6 9 .6 3
8 0 .0 1
1 3 .5
1 2 .5
1 0 .9
SATN
TITN
TITN
255
320
350
TITN
TITN
TITN
340
400
430
JUPT
JUPT
JUPT
450
450
550
JUPT
JUPT
JUPT
9 1 .4 1
9 9 .3 8
1 1 1 .5
9 .5
8 .8
7 .8
JUPT
TITN
JUPT
400
420
450
JUPT
500
JUPT
600
JUPT
600
1 2 1 .4
1 3 8 .5
1 5 9 .8
7 .2
6 .3
5 .4
JUPT
550
JUPT
650
1 9 3 .1
2 0 6 .2
2 3 8 .2
2 6 5 .4
4 .5
4 .2
3 .7
3 .3
2 9 5 .7
3 3 0 .1
3 6 9 .8
2 .9
2 .6
2 .4
4 1 2 .1
4 5 9 .0
5 3 2 .5
2 .1
1 .9
1 .6
6 1 7 .9
6 6 0 .6
7 4 1 .2
1 .4
1 .3
1 .2
9 0 0 .3
1057
0 .9 7
0 .8 2
3 0 HP
364T
VENS 16
ATLS 20
ATLS 26
ERTH 44
ERTH 48
ERTH 58
4 0 HP
365T
ERTH 24
ATLS 24
ERTH 34
PLRS 54
PLRS 70
PLRS 85
5 0 HP
404T
ERTH 24
ERTH 32
ERTH 46
NEPT 70
PLRS 80
NEPT 95
HP
1 5 0 HP
210
260
TITN
JUPT
250
300
TITN
JUPT
JUPT
320
350
450
JUPT
400
280
320
380
450
500
550
550
650
JUPT
175
210
270
TITN
TITN
TITN
240
280
350
2 0 0 HP
2 5 0 HP
SATN
120
650
If selection falls within shaded area, a cooling fan and shroud are required. Average ambient temperature below 84 F. See selection procedures page 5 for higher
ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
870rR2.p65
58
57
Black
7/19/2002, 10:35 AM
Approx.
N
Reduction ominal Output
Ratio
RPM
Single
Double
Triple
Quadruple
1 HP
143T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
145T C
M ER C 2
M ER C 2
M ER C 1
2 HP
145T C
M ER C 2
M ER C 2
M ER C 1
3 HP
182T C
M ER C 2
M ER C 2
M ER C 1
20 HP
256T C
VENS 10
VENS 10
VENS 11
25 HP
284T C
VENS 10
VENS 10
VENS 11
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
3
4
M ER C
M ER C
5
6
VEN S
VEN S
13
14
VEN S
VEN S
13
14
VEN S
VEN S
13
14
30 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 16
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
6
6
7
M ER C
M AR S
M AR S
6
8
10
VEN S
VEN S
VEN S
15
15
16
VEN S
VEN S
VEN S
15
15
18
VEN S
VEN S
VEN S
15
17
22
VEN S
VEN S
ATLS
19
21
26
3.53
4.39
6.12
9.30
11.02
13.85
496
399
286
188
159
126
17.21
20.41
24.00
102
86
86
73
73
M ER C
M ER C
M ER C
2
2
1
31.63
36.56
43.78
54.45
55
55
48
48
40
40
32
32
M ER C
M ER C
M ER C
M ER C
2
3
3d
2
M ER C
M ER C
M ER C
M ER C
2
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M AR S
M AR S
6
7
8d
9
M AR S
M AR S
M AR S
M AR S
9
11
12
15
M AR S
M AR S
M AR S
VEN S
11
13
16
20
VEN S
VEN S
VEN S
ATLS
17
19
24
30
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ATLS
ERTH
32
33
41
48
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
64.42
69.63
80.01
27
27
25
25
22
22
M ER C
M ER C
M ER C
4
3
4
M ER C
M ER C
M ER C
4
5
6
M ER C
M ER C
M ER C
6
5
6
M ER C
M ER C
M AR S
8
7
9
M AR S
M AR S
M AR S
11
13
15
M AR S
VEN S
VEN S
17
18
20
VEN S
ATLS
ATLS
22
27
30
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
50
56
ERTH
ERTH
ERTH
54
62
68
ERTH
PLRS
PLRS
66
75
80
91.41
99.38
111.5
19.1
17.6
15.7
M ER C
M ER C
M ER C
4
5
4
M ER C
M ER C
M ER C
6
7
6
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
11
11
13
M AR S
VEN S
VEN S
17
17
20
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ATLS
34
36
38
ERTH
ERTH
ERTH
48
52
56
ERTH
ERTH
70
74
PLRS
PLRS
85
100
PLRS
PLRS
105
110
121.4
138.5
159.8
14.4
12.6
11.0
M ER C
M ER C
M ER C
5q
5
6
M ER C
M AR S
M ER C
7q
9
8
M AR S
M AR S
M AR S
9q
11
11
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
9.1
8.5
7.3
6.6
M ER C 7
M ER C 8
M AR S 9
M ARS 10t
M AR S
M AR S
M AR S
M AR S
11
11
13
13
M AR S
M AR S
M AR S
VEN S
15
13
17
18
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
33
35
39
43
ERTH
ERTH
ERTH
ERTH
48
52
58
64
ERTH 64q
ERTH 70
ERTH 76
PLRS 90
295.7
330.1
369.8
5.9
5.3
4.7
M AR S
M AR S
M AR S
11
12
14
M AR S
M AR S
VEN S
15
18
20
VEN S
VEN S
VEN S
20
23
24
ATLS
ATLS
ATLS
31
32
39
ERTH
ERTH
ERTH
48
58
64
ERTH
PLRS
PLRS
72
80
90
PLRS
PLRS
PLRS
412.1
459.0
532.5
4.2
3.8
3.3
M AR S
M AR S
M AR S
14
16
18
VEN S
VEN S
ATLS
22
23
27
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
66
76
95
PLRS
PLRS
N EPT
617.9
660.6
741.2
2.8
2.6
2.4
VENS 21 ATLS 32 ERTH 46 ERTH 64 PLRS 110 NEPT 160 ORON 215
ERTH 30qu ERTH 36qu ERTH 48qu PLRS 70qu NEPT 120qu NEPT 160qu ORON 240
VENS 24 ATLS 35 ERTH 54 PLRS 85 NEPT 135 ORON 190
900.3
1057
1.9
1.7
ATLS
ERTH
E
C
A
F
C
32
36
140q
140
160
190
N EPT
O RO N
O RO N
O RO N
ERHT 48qu PLRS 65qu PLRS 95qu NEPT 150qu ORON 215
ERTH 54 PLRS 70qu PLRS 100qu ORON 190
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
59
1750cfR2.p65
58
Black
7/19/2002, 10:18 AM
Approx.
N
Reduction ominal Output
Ratio
RPM
Single
Double
Triple
Quadruple
1 HP
143T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
145T C
M ER C 2
M ER C 2
M ER C 1
2 HP
145T C
M ER C 2
M ER C 2
M ER C 1
3 HP
182T C
M ER C 2
M ER C 2
M ER C 1
20 HP
256T C
VENS 10
VENS 10
VENS 11
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
3
4
M ER C
M ER C
3
4
M ER C
M ER C
5
6
M ER C
M AR S
5
8
VEN S
VEN S
13
14
VEN S
VEN S
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
6
6
7
M AR S
M AR S
M AR S
7
8
10
M AR S
M AR S
M AR S
9
12
12
VEN S
VEN S
VEN S
15
15
18
13
14
25 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 15
VENS 18
30 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 20
VEN S
VEN S
ATLS
17
19
26
VEN S
VEN S
ATLS
21
23
30
ATLS
ATLS
ATLS
26
30
34
3.53
4.39
6.12
9.30
11.02
13.85
496
399
286
188
159
126
17.21
20.41
24.00
102
86
86
73
73
M ER C
M ER C
M ER C
2
2
3
31.63
36.56
43.78
54.45
55
55
48
48
40
40
32
32
M ER C
M ER C
M ER C
M ER C
2
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
3
5d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S
M AR S
M AR S
M AR S
9
9
12
13
M AR S
M AR S
M AR S
VEN S
11
15
16
20
VEN S
VEN S
VEN S
ATLS
17
19
22
30
ATLS
ATLS
ATLS
ATLS
24
29
33
42
ATLS
ATLS
ERTH
ERTH
32
37
48
54
ATLS
ERTH
ERTH
ERTH
38t
46
54
66
ERTH
ERTH
ERTH
PLRS
50
52
66
80
64.42
69.63
80.01
27
27
25
25
22
22
M ER C
M ER C
M ER C
4
5
4
M ER C
M ER C
M ER C
6
5
6
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
VEN S
17
17
20
VEN S
ATLS
ATLS
24
27
30
ATLS
ATLS
ATLS
30
35
38
ERTH
ERTH
ERTH
48
50
56
ERTH
ERTH
ERTH
60
68
74
PLRS
PLRS
PLRS
80
85
100
PLRS
PLRS
PLRS
90
105
110
91.41
99.38
111.5
19.1
17.6
15.7
M ER C
M ER C
M ER C
6
5
6
M ER C
M AR S
M ER C
8
9
8
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
ATLS
22
23
26
ATLS
ATLS
ATLS
34
36
42
ERTH
ERTH
ERTH
48
46
56
ERTH
PLRS
70
80
PLRS
PLRS
95
110
121.4
138.5
159.8
14.4
12.6
11.0
M ER C
M ER C
M ER C
7q
7
8
M AR S
M AR S
M AR S
9q
11
13
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
9.1
8.5
7.3
6.6
M AR S
M AR S
M AR S
M AR S
11
11
13
13
M AR S
M AR S
M AR S
VEN S
15
15
17
18
VEN S
VEN S
VEN S
VEN S
18
20
22
24
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
48
52
58
64
ERTH 64q
ERTH 76
PLRS 80
PLRS 90
N EPT
N EPT
N EPT
O RO N
295.7
330.1
369.8
5.9
5.3
4.7
M AR S
M AR S
M AR S
15
16
18
VEN S
VEN S
ATLS
22
23
27
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
PLRS
66
76
90
PLRS
PLRS
N EPT
412.1
459.0
532.5
4.2
3.8
3.3
VEN S
VEN S
VEN S
20
21
24
ATLS
ATLS
ATLS
31
32
35
ATLS
ERTH
ERTH
39
46
54
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
N EPT
617.9
660.6
741.2
2.8
2.6
2.4
900.3
1057
1.9
1.7
ERTH 42qu PLRS 65qu PLRS 85qu NEPT 130qu ORON 215
ERTH 54 PLRS 70qu PLRS 100qu ORON 190 ORON 240
E
C
A
F
C
PLRS 90q
PLRS 100
PLRS 110
PLRS 120
140q
150
160
190
O RO N
O RO N
O RO N
O RO N
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
1750cfR2.p65
60
59
Black
7/19/2002, 10:19 AM
Approx.
N
Reduction ominal Output
Ratio
RPM
Single
Double
Triple
Quadruple
3
4
20 HP
256T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 20
25 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
30 HP
286T C
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
4
6
7
M ER C
M AR S
M AR S
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
40
54
66t
80
95
120
1 HP
143T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
145T C
M ER C 2
M ER C 2
M ER C 1
2 HP
145T C
M ER C 2
M ER C 2
M ER C 1
3 HP
182T C
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
2
M ER C
M ER C
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
3.53
4.39
6.12
9.30
11.02
13.85
496
399
286
188
159
126
17.21
20.41
24.00
102
86
86
73
73
M ER C
M ER C
M ER C
2
2
3
31.63
36.56
43.78
54.45
55
55
48
48
40
40
32
32
M ER C
M ER C
M ER C
M ER C
4
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
VEN S
11
13
16
20
VEN S
VEN S
VEN S
ATLS
17
19
24
30
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
ERTH
ERTH
PLRS
PLRS
62t ERTH
64 PLRS
85 PLRS
100 PLRS
64.42
69.63
80.01
27
27
25
25
22
22
M ER C
M ER C
M ER C
6
5
6
M ER C
M ER C
M AR S
8
7
9
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
15
15
17
VEN S
ATLS
ATLS
22
27
30
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
90
95
110
PLRS
110
91.41
99.38
111.5
19.1
17.6
15.7
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
VEN S
22
21
22
ATLS
ATLS
ATLS
34
36
38
ERTH
ERTH
ERTH
48
52
56
ERTH
ERTH
70
74
PLRS
PLRS
105
110
121.4
138.5
159.8
14.4
12.6
11.0
M AR S
M AR S
M AR S
9q
11
11
M ARS 13q M ARS 17q ERTH 26q ERTH 44q ERTH 62q
M ARS 15 VENS 19 ATLS 31 ERTH 46 ERTH 70
M ARS 17 VENS 24q ATLS 35q ERTH 50q ERTH 74q
193.1
206.2
238.2
265.4
9.1
8.5
7.3
6.6
M AR S
M AR S
M AR S
VEN S
15
13
17
18
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
31
35
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH 64q
ERTH 70
ERTH 76
PLRS 90
295.7
330.1
369.8
5.9
5.3
4.7
VEN S
VEN S
VEN S
20
23
24
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
412.1
459.0
532.5
4.2
3.8
3.3
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
54
64
75
PLRS
PLRS
PLRS
617.9
660.6
741.2
2.8
2.6
2.4
900.3
1057
1.9
1.7
6
8
10
M AR S
M AR S
M AR S
9
12
14
M AR S
VEN S
VEN S
13
15
18
VEN S
VEN S
ATLS
19
21
26
E
C
A
F
C
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1750 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
61
1750cfR2.p65
60
Black
7/19/2002, 10:19 AM
Approx.
N
Reduction ominal Output
Ratio
RPM
Single
Double
Triple
Quadruple
1 HP
143T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
145T C
M ER C 2
M ER C 2
M ER C 1
2 HP
145T C
M ER C 2
M ER C 2
M ER C 1
3 HP
182T C
M ER C 2
M ER C 2
M ER C 1
20 HP
256T C
VENS 10
VENS 10
VENS 11
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
5
6
M ER C
M ER C
5
6
VEN S
VEN S
13
14
VEN S
VEN S
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
4
6
7
M ER C
M AR S
M AR S
6
8
8
M AR S
M AR S
M AR S
9
10
12
VEN S
VEN S
VEN S
15
15
16
13
14
25 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 16
30 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 15
VENS 18
VEN S
VEN S
VEN S
15
17
20
VEN S
VEN S
ATLS
19
21
26
ATLS
ATLS
ATLS
22
26
30
3.53
4.39
6.12
9.30
11.02
13.85
405
326
234
154
130
103
17.21
20.41
24.00
83
83
70
70
60
60
M ER C
M ER C
M ER C
2
2
3
31.63
36.56
43.78
54.45
45
45
39
39
33
33
26
26
M ER C
M ER C
M ER C
M ER C
2
3
3d
4
M ER C
M ER C
M ER C
M ER C
2
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
4
5
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
11
13
14
17
M AR S
VEN S
VEN S
VEN S
13
17
20
24
ATLS
VEN S
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ATLS
ERTH
28
33
41
48
ATLS
ATLS
ERTH
ERTH
34t
41
48
60
ERTH
ERTH
ERTH
ERTH
44
46
60
72
64.42
69.63
80.01
22
22
21
21
17.9
M ER C
M ER C
M ER C
4
3
4
M ER C
M ER C
M ER C
6
5
6
M ER C
M ER C
M ER C
6
7
8
M AR S
M AR S
M AR S
9
9
11
M AR S
M AR S
M AR S
15
15
17
VEN S
VEN S
ATLS
20
22
26
ATLS
ATLS
ATLS
26
31
34
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
54
62
68
ERTH
PLRS
PLRS
66
75
90
PLRS
PLRS
PLRS
80
95
100
91.41
99.38
111.5
15.6
14.4
12.9
M ER C
M ER C
M ER C
4
5
6
M ER C
M ER C
M ER C
6
7
8
M ER C
M AR S
M AR S
8
9
11
M AR S
M AR S
M AR S
13
13
15
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
30
32
34
ERTH
ATLS
ERTH
42
40
50
ERTH
ERTH
64
68
PLRS
PLRS
85
90
PLRS
PLRS
105
120
121.4
138.5
159.8
11.8
10.3
8.9
M ER C
M ER C
M ER C
5q
7
8
M AR S
M AR S
M AR S
9q
9
11
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
7.4
6.9
6.0
5.4
M AR S
M ER C
M AR S
M AR S
9
8
11
13
M AR S
M AR S
M AR S
M AR S
13
13
15
17
VEN S
M AR S
VEN S
VEN S
16
17
20
22
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ERTH
ATLS
ERTH
ERTH
42
43
52
52
ERTH
ERTH
ERTH
PLRS
60
64
70
80
N EPT
O RO N
O RO N
O RO N
295.7
330.1
369.8
4.8
4.3
3.9
M AR S
M AR S
M AR S
13
14
16
VEN S
VEN S
VEN S
18
21
22
VEN S
ATLS
ATLS
24
28
31
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
60
70
76
PLRS
PLRS
PLRS
95 PLRS
100 NEPT
110 NEPT
412.1
459.0
532.5
3.5
3.1
2.7
M AR S
VEN S
VEN S
18
19
22
ATLS
ATLS
ATLS
27
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
58
72
PLRS
PLRS
PLRS
617.9
660.6
741.2
2.3
2.2
1.9
900.3
1057
1.6
1.4
ATLS
ERTH
E
C
A
F
C
36
48
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
62
1430cfR2.p65
61
Black
7/19/2002, 10:11 AM
pprox.
ominal A
Reduction NR
utput
atio OR
PM
Single
Double
Triple
Quadruple
1 HP
143T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
145T C
M ER C 2
M ER C 2
M ER C 1
2 HP
145T C
M ER C 2
M ER C 2
M ER C 1
3 HP
182T C
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
5
6
M ER C
M AR S
5
8
M AR S
M AR S
8
10
VEN S
VEN S
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
4
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M AR S
M AR S
6
8
8
M AR S
M AR S
M AR S
9
10
12
M AR S
VEN S
VEN S
11
15
16
VEN S
VEN S
VEN S
13
14
20 HP
256T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 18
25 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 22
30 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 18
VENS 21
ATLS 26
15
17
22
VEN S
VEN S
ATLS
21
23
30
ATLS
ATLS
ATLS
26
30
38
ATLS
ATLS
ERTH
30
34
42
3.53
4.39
6.12
9.30
11.02
13.85
405
326
234
154
130
103
17.21
20.41
24.00
83
83
70
70
60
60
M ER C
M ER C
M ER C
2
2
3
31.63
36.56
43.78
54.45
45
45
39
39
33
33
26
26
M ER C
M ER C
M ER C
M ER C
2
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
4
5
5d
8
M ER C
M ER C
M AR S
M AR S
6
7
8d
11
M AR S
M AR S
M AR S
M AR S
9
11
14
17
VEN S
VEN S
VEN S
ATLS
15
17
20
26
ATLS
VEN S
ATLS
ATLS
20
21
29
34
ATLS
ATLS
ATLS
ERTH
32
33
41
54
ATLS
ERTH
ERTH
ERTH
38t
46
54
66
ERTH
ERTH
ERTH
PLRS
50
58
66
90
ERTH
ERTH
PLRS
PLRS
62t
64
85
100
64.42
69.63
80.01
22
22
21
21
17.9
M ER C
M ER C
M ER C
4
5
6
M ER C
M ER C
M ER C
6
7
8
M ER C
M AR S
M AR S
8
9
11
M AR S
M AR S
M AR S
13
13
15
VEN S
VEN S
VEN S
20
20
24
ATLS
ATLS
ATLS
30
31
34
ATLS
ERTH
ERTH
38
44
50
ERTH
ERTH
ERTH
60
62
68
PLRS
PLRS
PLRS
80
85
90
PLRS
PLRS
PLRS
100
105
120
PLRS
110
91.41
99.38
111.5
15.6
14.4
12.9
M ER C
M ER C
M ER C
6
7
8
M ER C
M AR S
M AR S
8
9
11
M AR S
M AR S
M AR S
11
13
15
M AR S
VEN S
VEN S
17
17
20
ATLS
ATLS
ATLS
30
28
34
ERTH
ERTH
ERTH
42
46
50
ERTH
ERTH
ERTH
54
58
68
PLRS
PLRS
85
100
121.4
138.5
159.8
11.8
10.3
8.9
M ER C
M AR S
M AR S
7q
9
11
M ARS 11q M ARS 15q ATLS 22q ATLS 34q ERTH 56q ERTH 68q
M ARS 13 VENS 17 VENS 24q ATLS 39 ERTH 64 PLRS 80
M ARS 15 VENS 20q ATLS 31q ERTH 44q ERTH 68q PLRS 90q
193.1
206.2
238.2
265.4
7.4
6.9
6.0
5.4
M AR S
M AR S
M AR S
M AR S
13
13
15
15
VEN S
M AR S
VEN S
VEN S
18
17
20
22
ATLS
VEN S
ATLS
ATLS
25
24
27
31
ATLS
ATLS
ATLS
ERTH
33
39
43
46
ERTH
ERTH
ERTH
ERTH
60
64
70
76
N EPT
O RO N
O RO N
O RO N
295.7
330.1
369.8
4.8
4.3
3.9
VEN S
VEN S
VEN S
18
19
22
ATLS
ATLS
ATLS
27
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
58
64
PLRS
PLRS
PLRS
85 NEPT
90 NEPT
110 NEPT
412.1
459.0
532.5
3.5
3.1
2.7
VEN S
ATLS
ATLS
24
28
31
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
52
66
ERTH
ERTH
PLRS
72
76
95
617.9
660.6
741.2
2.3
2.2
1.9
900.3
1057
1.6
1.4
ERTH 54qu PLRS 85qu PLRS 105qu NEPT 150qu ORON 240
PLRS 70qu PLRS 90qu PLRS 120qu ORON 190
E
C
A
F
C
PLRS 80q PLRS 110q
PLRS 90 PLRS 120
PLRS 100 NEPT 130
PLRS 110 NEPT 150
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
63
1430cfR2.p65
62
Black
7/19/2002, 10:12 AM
pprox.
ominal A
Reduction NR
utput
atio OR
PM
Single
Double
Triple
Quadruple
3
4
20 HP
256T C
VENS 10
VENS 10
VENS 11
ATLS 18
VENS 19
ATLS 26
25 HP
284T C
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
30 HP
286T C
VENS 10
VENS 12
VENS 15
ATLS 26
ATLS 28
ATLS 38
6
6
7
M AR S
M AR S
M AR S
22
26
30
ATLS
ATLS
ERTH
30
34
42
ATLS
ERTH
ERTH
38
40
54
ERTH
ERTH
ERTH
46
52
60
PLRS
PLRS
PLRS
PLRS
70t
80
95
120
PLRS
PLRS
90
115
1 HP
143T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
145T C
M ER C 2
M ER C 2
M ER C 1
2 HP
145T C
M ER C 2
M ER C 2
M ER C 3
3 HP
182T C
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
3.53
4.39
6.12
9.30
11.02
13.85
405
326
234
154
130
103
17.21
20.41
24.00
83
83
70
70
60
60
M ER C
M ER C
M ER C
2
2
3
31.63
36.56
43.78
54.45
45
45
39
39
33
33
26
26
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
4
5
7
8
M ER C
M ER C
M AR S
M AR S
6
7
8d
9
M AR S
M AR S
M AR S
M AR S
9
11
12
13
M AR S
VEN S
VEN S
VEN S
13
17
20
24
ATLS
VEN S
ATLS
ATLS
24
23
29
38
ATLS
ATLS
ATLS
ERTH
28
33
41
48
ERTH
ERTH
ERTH
ERTH
44
46
60
72
ERTH
ERTH
PLRS
PLRS
56
64
75
100
64.42
69.63
80.01
22
22
21
21
17.9
M ER C
M ER C
M ER C
6
7
8
M AR S
M AR S
M AR S
9
9
11
M AR S
M AR S
M AR S
11
13
15
M AR S
VEN S
VEN S
17
18
20
ATLS
ATLS
ATLS
26
31
34
ATLS
ERTH
ERTH
42
44
50
ERTH
ERTH
ERTH
54
62
68
PLRS
PLRS
PLRS
80
95
100
PLRS
110
91.41
99.38
111.5
15.6
14.4
12.9
M ER C
M AR S
M AR S
8
9
11
M AR S
M AR S
M AR S
13
13
15
M AR S
VEN S
VEN S
15
17
18
ATLS
ATLS
ATLS
26
24
30
ERTH
ATLS
ERTH
42
40
50
ERTH
ERTH
64
68
PLRS
PLRS
85
90
121.4
138.5
159.8
11.8
10.3
8.9
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
7.4
6.9
6.0
5.4
VEN S
M AR S
VEN S
VEN S
16
17
20
22
ATLS
ATLS
ATLS
ATLS
25
27
31
35
ATLS
ATLS
ATLS
ATLS
33
35
39
43
ERTH
ERTH
ERTH
ERTH
48
52
58
64
N EPT
O RO N
O RO N
O RO N
295.7
330.1
369.8
4.8
4.3
3.9
VEN S
ATLS
ATLS
24
28
31
ATLS
ATLS
ERTH
39
40
46
ERTH
ERTH
ERTH
48
52
58
ERTH
PLRS
PLRS
72
80
90
PLRS
N EPT
N EPT
412.1
459.0
532.5
3.5
3.1
2.7
ATLS
ATLS
ATLS
35
40
43
ERTH
ERTH
ERTH
48
58
72
ERTH
ERTH
PLRS
66
76
95
PLRS
PLRS
N EPT
617.9
660.6
741.2
2.3
2.2
1.9
900.3
1057
1.6
1.4
9
10
12
M AR S
VEN S
VEN S
11
15
16
VEN S
VEN S
VEN S
15
17
20
ATLS
ATLS
ATLS
E
C
A
F
C
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1430 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional ratios are
available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
64
1430cfR2.p65
63
Black
7/19/2002, 10:12 AM
Reduction
Single
Double
Triple
Quadruple
1 HP
145T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
182T C
M ER C 2
M ER C 2
M ER C 1
2 HP
184T C
M ER C 2
M ER C 2
M ER C 1
15 HP
284T C
VENS 10
VENS 10
VENS 11
M ER C
M ER C
1
2
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
3
4
VEN S
VEN S
13
14
VEN S
VEN S
13
14
VEN S
VEN S
13
14
20 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 14
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
6
6
7
VEN S
VEN S
VEN S
15
15
16
VEN S
VEN S
VEN S
15
15
16
VEN S
VEN S
VEN S
15
15
20
VEN S
VEN S
ATLS
19
21
26
VEN S
VEN S
VEN S
ATLS
E
C
A
F
C
17
19
24
30
ATLS
ATLS
ATLS
ATLS
28
29
37
43
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
24
27
30
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
48
56
62
ERTH
PLRS
PLRS
66
75
80
38
40
42
ERTH
ERTH
ERTH
48
52
56
PLRS
PLRS
75
90
PLRS
PLRS
105
110
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
331
267
191
126
106
84
84
17.21
20.41
24.00
68
68
57
57
49
49
31.63
36.56
43.78
54.45
37
37
32
32
26
26
21
21
M ER C
M ER C
M ER C
M ER C
2
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
3
5d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S
M AR S
M AR S
M AR S
9
11
12
15
VEN S
VEN S
VEN S
VEN S
15
17
18
22
64.42
69.63
80.01
18.2
16.8
14.6
M ER C
M ER C
M ER C
4
5
6
M ER C
M ER C
M ER C
6
7
8
M ER C
M ER C
M AR S
8
7
9
M AR S
M AR S
M AR S
11
11
13
M AR S
VEN S
VEN S
17
18
20
VEN S
ATLS
ATLS
91.41
99.38
111.5
12.8
11.8
10.5
M ER C
M ER C
M ER C
6
7
6
M ER C
M AR S
M AR S
8
9
9
M AR S
M AR S
M AR S
11
11
13
M AR S
VEN S
M AR S
15
17
17
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ATLS
121.4
138.5
159.8
9.6
8.4
7.3
M ER C
M AR S
M ER C
7q
9
8
M AR S
M AR S
M AR S
9q
11
13
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
6.1
5.7
4.9
4.4
M AR S
M AR S
M AR S
M AR S
11
11
13
13
M AR S
M AR S
VEN S
VEN S
15
15
18
20
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
48
52
58
64
295.7
330.1
369.8
4
3.5
3.2
M AR S
M AR S
VEN S
15
18
20
VEN S
ATLS
ATLS
22
24
27
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
43
52
58
ERTH
PLRS
PLRS
72
80
90
PLRS
PLRS
N EPT
412.1
459.0
532.5
2.8
2.5
2.2
VEN S
VEN S
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
N EPT
617.9
660.6
741.2
1.9
1.8
1.6
900.3
1057
1.3
1.1
ERTH 48qu PLRS 75qu PLRS 95qu NEPT 140qu ORON 215
ERTH 54 PLRS 80qu PLRS 100qu ORON 190
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional
ratios are available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
65
1170cfR2.p65
64
Black
7/19/2002, 9:37 AM
Reduction
Single
Double
Triple
Quadruple
1 HP
145T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
182T C
M ER C 2
M ER C 2
M ER C 1
2 HP
184T C
M ER C 2
M ER C 2
M ER C 1
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
3
4
M ER C
M ER C
5
6
VEN S
VEN S
13
14
VEN S
VEN S
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M AR S
4
6
7
M AR S
M AR S
M AR S
7
8
10
VEN S
VEN S
VEN S
15
15
16
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
331
267
191
126
106
84
84
17.21
20.41
24.00
68
68
57
57
49
49
31.63
36.56
43.78
54.45
37
37
32
32
26
26
21
21
M ER C
M ER C
M ER C
M ER C
4
3
5d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 13
M AR S
M AR S
M AR S
VEN S
11
15
16
20
VEN S
VEN S
VEN S
ATLS
19
21
24
30
64.42
69.63
80.01
18.2
16.8
14.6
M ER C
M ER C
M ER C
6
5
6
M ER C
M AR S
M AR S
8
9
9
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
VEN S
15
15
18
VEN S
ATLS
ATLS
24
27
30
ATLS
ATLS
ATLS
91.41
99.38
111.5
12.8
11.8
10.5
M ER C
M AR S
M ER C
8
9
8
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
34
36
42
ERTH
ERTH
ERTH
121.4
138.5
159.8
9.6
8.4
7.3
M AR S
M AR S
M AR S
9q
11
13
ATLS
ATLS
ATLS
193.1
206.2
238.2
265.4
6.1
5.7
4.9
4.4
M AR S
M AR S
M AR S
VEN S
15
15
17
18
VEN S
VEN S
ATLS
ATLS
20
22
27
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ERTH
ERTH
ERTH
42
46
52
58
ERTH 64q
ERTH 76
PLRS 80
PLRS 90
295.7
330.1
369.8
4
3.5
3.2
VEN S
VEN S
ATLS
22
23
27
ATLS
ATLS
ATLS
31
36
39
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
60
70
76
PLRS
PLRS
N EPT
412.1
459.0
532.5
2.8
2.5
2.2
ATLS
ATLS
ATLS
31
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
PLRS
617.9
660.6
741.2
1.9
1.8
1.6
900.3
1057
1.3
1.1
13
14
15 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 16
20 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 20
VEN S
VEN S
VEN S
15
15
18
VEN S
VEN S
ATLS
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ATLS
ATLS
ATLS
E
C
A
F
C
24
29
33
42
ATLS
ATLS
ERTH
ERTH
34t
41
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
34
39
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
72
75
90
PLRS
PLRS
PLRS
90
105
110
54
52
62
ERTH
PLRS
70
80
PLRS
PLRS
105
120
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional
ratios are available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
1170cfR2.p65
65
Black
66
7/19/2002, 9:38 AM
Reduction
Single
Double
Triple
Quadruple
3
4
10 HP
256T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 14
15 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 18
VENS 17
VENS 22
20 HP
286T C
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
4
6
5
M ER C
M AR S
M AR S
VEN S
VEN S
ATLS
19
21
26
ATLS
ATLS
ATLS
30
30
38
ATLS
ERTH
ERTH
38
40
54
ATLS
ATLS
ERTH
ERTH
E
C
A
F
C
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
56
58
72
90
ERTH
PLRS
PLRS
PLRS
66t
80
95
120
48
56
62
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
100
105
120
75
90
PLRS
PLRS
105
110
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
331
267
191
126
106
84
84
17.21
20.41
24.00
68
68
57
57
49
49
31.63
36.56
43.78
54.45
37
37
32
32
26
26
21
21
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
11
13
14
17
VEN S
VEN S
VEN S
ATLS
17
19
24
30
ATLS
ATLS
ATLS
ATLS
28
29
37
42
64.42
69.63
80.01
18.2
16.8
14.6
M ER C
M ER C
M AR S
8
7
9
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
M AR S
15
15
17
VEN S
VEN S
VEN S
20
22
24
ATLS
ATLS
ATLS
34
35
42
ERTH
ERTH
ERTH
91.41
99.38
111.5
12.8
11.8
10.5
M AR S
M AR S
M AR S
11
11
13
M AR S
VEN S
M AR S
15
17
17
ATLS
VEN S
VEN S
22
21
22
ATLS
ATLS
ATLS
30
32
34
ERTH
ERTH
ERTH
48
52
56
PLRS
PLRS
121.4
138.5
159.8
9.6
8.4
7.3
ATLS
ATLS
ATLS
26q
31
35
193.1
206.2
238.2
265.4
6.1
5.7
4.9
4.4
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH
ERTH
ERTH
ERTH
60
64
70
76
295.7
330.1
369.8
4
3.5
3.2
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
43
52
58
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
412.1
459.0
532.5
2.8
2.5
2.2
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
60
70
85
PLRS
PLRS
PLRS
617.9
660.6
741.2
1.9
1.8
1.6
900.3
1057
1.3
1.1
1 HP
145T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
182T C
M ER C 2
M ER C 2
M ER C 3
2 HP
184T C
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
3
2
M ER C
M ER C
3
4
M ER C
M ER C
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
6
8
8
M AR S
M AR S
M AR S
9
12
14
VEN S
VEN S
VEN S
15
15
20
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 1170 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to factory. Additional
ratios are available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
67
1170cfR2.p65
66
Black
7/19/2002, 9:38 AM
Reduction
Single
Double
10 HP
284T C
VENS 10
VENS 10
VENS 11
M ER C
M ER C
1
2
M ER C
M ER C
3
2
M ER C
M ER C
3
2
M ER C
M ER C
3
4
VEN S
VEN S
13
14
VEN S
VEN S
13
14
VEN S
VEN S
13
14
15 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 16
M ER C
M ER C
M ER C
2
2
3
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
4
6
7
VEN S
VEN S
VEN S
15
15
16
VEN S
VEN S
VEN S
15
15
16
VEN S
VEN S
VEN S
15
15
18
VEN S
VEN S
ATLS
19
21
26
E
C
A
F
C
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
51
51
43
43
36
36
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
4
3
3d
4
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
VEN S
VEN S
VEN S
VEN S
15
17
18
20
VEN S
VEN S
VEN S
ATLS
19
19
24
30
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
13.5
12.5
10.9
M ER C
M ER C
M ER C
6
5
6
M ER C
M AR S
M ER C
8
9
9
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
15
15
17
VEN S
ATLS
ATLS
22
27
30
ATLS
ATLS
ATLS
34
39
42
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
66
75
80
9.5
8.8
7.8
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
34
36
38
ERTH
ERTH
ERTH
48
52
56
ERTH
ERTH
70
74
PLRS
PLRS
105
120
7.2
6.3
5.4
M AR S
M AR S
M AR S
9q
11
11
ATLS
ATLS
ATLS
4.5
4.2
3.7
3.3
M AR S
M AR S
M AR S
VEN S
15
13
17
18
VEN S
VEN S
VEN S
ATLS
20
22
24
27
ATLS
ATLS
ATLS
ATLS
29
31
35
35
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH 64q
ERTH 70
ERTH 76
PLRS 90
295.7
330.1
369.8
2.9
2.6
2.4
VEN S
VEN S
VEN S
20
23
24
ATLS
ATLS
ATLS
31
32
39
ATLS
ERTH
ERTH
39
46
52
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
412.1
459.0
532.5
2.1
1.9
1.6
ATLS
ATLS
ATLS
27
32
35
ATLS
ERTH
ERTH
43
46
60
ERTH
ERTH
PLRS
54
64
75
PLRS
PLRS
PLRS
617.9
660.6
741.2
1.4
1.3
1.2
900.3
1057
0.97
0.82
64.42
69.63
80.01
91.41
99.38
111.5
121.4
138.5
159.8
193.1
206.2
238.2
265.4
Quadruple
1.5 HP
184T C
M ER C 2
M ER C 2
M ER C 1
Approx.
Output
RPM
31.63
36.56
43.78
54.45
Triple
1 HP
182T C
M ER C 2
M ER C 2
M ER C 1
Nominal
Ratio
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to
factory. Additional ratios are available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
68
870cfR2.p65
67
Black
7/19/2002, 10:28 AM
Reduction
Single
Double
Nominal
Ratio
Approx.
Output
RPM
3.53
4.39
6.12
9.30
11.02
13.85
246
198
142
94
94
79
79
63
63
17.21
20.41
24.00
51
51
43
43
36
36
M ER C
M ER C
1
2
M ER C
M ER C
3
4
M ER C
M ER C
3
4
M ER C
M ER C
3
6
VEN S
VEN S
13
14
VEN S
VEN S
M ER C
M ER C
M ER C
2
4
3
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
4
6
5
M ER C
M AR S
M AR S
6
8
8
VEN S
VEN S
VEN S
15
15
16
VEN S
VEN S
VEN S
13
14
10 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 13
VENS 14
15 HP
286T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 20
15
15
18
VEN S
VEN S
ATLS
17
19
26
ATLS
ATLS
ATLS
26
30
38
E
C
A
F
C
M ER C
M ER C
M ER C
M ER C
4
5
5d
6
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M ER C 6
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
9
11
14
15
VEN S
VEN S
VEN S
ATLS
17
19
22
30
ATLS
ATLS
ATLS
ATLS
24
29
33
42
ATLS
ATLS
ERTH
ERTH
32
37
48
54
ERTH
ERTH
ERTH
PLRS
50
52
66
80
13.5
12.5
10.9
M ER C
M ER C
M ER C
8
7
8
M AR S
M AR S
M AR S
11
11
13
M AR S
M AR S
M AR S
13
15
17
VEN S
VEN S
VEN S
18
20
24
ATLS
ATLS
ATLS
30
35
38
ERTH
ERTH
ERTH
48
50
56
ERTH
ERTH
ERTH
60
68
74
PLRS
PLRS
PLRS
90
105
120
9.5
8.8
7.8
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
VEN S
22
19
22
ATLS
ATLS
ATLS
30
28
34
ERTH
ERTH
ERTH
48
46
56
ERTH
PLRS
70
80
PLRS
PLRS
95
110
7.2
6.3
5.4
M AR S
M AR S
M AR S
13
15
15
M ARS 17
VENS 21
VENS 24q
ATLS
ATLS
ATLS
4.5
4.2
3.7
3.3
VEN S
VEN S
VEN S
ATLS
18
20
22
27
ATLS
ATLS
ATLS
ATLS
29
31
35
39
ERTH
ATLS
ERTH
ERTH
36
39
46
52
ERTH
ERTH
ERTH
ERTH
54
58
64
76
N EPT
N EPT
N EPT
O RO N
295.7
330.1
369.8
2.9
2.6
2.4
ATLS
ATLS
ATLS
31
32
35
ATLS
ERTH
ERTH
43
46
52
ERTH
ERTH
ERTH
54
64
70
PLRS
PLRS
PLRS
412.1
459.0
532.5
2.1
1.9
1.6
ATLS
ERTH
ERTH
39
46
54
ERTH
ERTH
PLRS
60
64
85
PLRS
PLRS
PLRS
75 PLRS
90 NEPT
105 NEPT
617.9
660.6
741.2
1.4
1.3
1.2
900.3
1057
0.97
0.82
64.42
69.63
80.01
91.41
99.38
111.5
121.4
138.5
159.8
193.1
206.2
238.2
265.4
Quadruple
1.5 HP
184T C
M ER C 2
M ER C 2
M ER C 1
28
28
24
24
20
20
16
16
31.63
36.56
43.78
54.45
Triple
1 HP
182T C
M ER C 2
M ER C 2
M ER C 1
PLRS 90q
PLRS 100
PLRS 110
PLRS 120
140q
150
160
190
O RO N
O RO N
O RO N
O RO N
190q
215
230
240
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to
factory. Additional ratios are available as standard items. Contact Rexnord for application details.
Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
69
870cfR2.p65
68
Black
7/19/2002, 10:29 AM
Reduction
Single
Double
15 HP
286T C
VENS 10
VENS 10
VENS 13
ATLS 22
ATLS 24
ATLS 30
4
6
7
M ER C
M ER C
M ER C
19
21
26
ATLS
ATLS
ATLS
26
30
34
ATLS
ERTH
ERTH
38
40
54
E
C
A
F
C
ERTH
PLRS
PLRS
PLRS
66t
80
95
120
3.53
4.39
6.12
9.30
11.02
13.85
17.21
20.41
24.00
246
198
142
94
94
79
79
63
63
1 HP
182T C
M ER C 2
M ER C 2
M ER C 1
1.5 HP
184T C
M ER C 2
M ER C 2
M ER C 3
M ER C
M ER C
3
2
M ER C
M ER C
51
51
43
43
36
36
M ER C
M ER C
M ER C
4
4
5
M ER C
M ER C
M ER C
6
6
7
M AR S
M AR S
M AR S
9
10
12
VEN S
VEN S
VEN S
15
15
18
VEN S
VEN S
ATLS
28
28
24
24
20
20
16
16
M ER C
M ER C
M ER C
M ER C
6
7
7
8
M AR S 7
M AR S 9
M ARS 10d
M ARS 11
M AR S
M AR S
M AR S
M AR S
9
11
14
15
M AR S
VEN S
VEN S
VEN S
13
17
20
24
ATLS
ATLS
ATLS
ATLS
24
25
33
38
ATLS
ATLS
ERTH
ERTH
34t
37
48
60
ERTH
ERTH
ERTH
PLRS
50
52
66
80
13.5
12.5
10.9
M AR S
M AR S
M AR S
9
11
11
M AR S
M AR S
M AR S
15
15
17
VEN S
VEN S
VEN S
18
20
22
ATLS
ATLS
ATLS
26
31
34
ERTH
ERTH
ERTH
48
50
56
ERTH
PLRS
PLRS
66
75
80
PLRS
PLRS
PLRS
90
95
110
9.5
8.8
7.8
M AR S
M AR S
M AR S
13
15
17
ATLS
VEN S
VEN S
22
21
24
ATLS
ATLS
ATLS
26
28
30
ATLS
ATLS
ERTH
38
40
50
ERTH
ERTH
70
74
PLRS
PLRS
105
120
7.2
6.3
5.4
M ARS 17
VENS 19
VENS 24q
ATLS
ATLS
ATLS
4.5
4.2
3.7
3.3
ATLS
ATLS
ATLS
ATLS
29
31
35
35
ERTH
ATLS
ERTH
ERTH
42
43
46
52
ERTH
ERTH
ERTH
ERTH
54
58
64
70
N EPT
N EPT
N EPT
O RO N
295.7
330.1
369.8
2.9
2.6
2.4
ATLS
ERTH
ERTH
39
46
52
ERTH
ERTH
ERTH
60
64
76
PLRS
PLRS
PLRS
85 PLRS
90 NEPT
100 NEPT
412.1
459.0
532.5
2.1
1.9
1.6
ERTH
ERTH
PLRS
54
64
75
PLRS
PLRS
PLRS
85 PLRS
90 PLRS
115 NEPT
617.9
660.6
741.2
1.4
1.3
1.2
900.3
1057
0.97
0.82
64.42
69.63
80.01
91.41
99.38
111.5
121.4
138.5
159.8
193.1
206.2
238.2
265.4
Quadruple
10 HP
284T C
VENS 10
VENS 10
VENS 11
ATLS 14
VENS 17
VENS 20
Approx.
Output
RPM
31.63
36.56
43.78
54.45
Triple
3
4
Nominal
Ratio
ERTH 76q
PLRS 90
PLRS 100
PLRS 110
Average ambient temperature below 84 F. See selection procedures page 5 for higher ambient temperatures.
* Selections are based on 870 RPM, NEMA B, T-Frame motors. If other motor types, speeds, or HP's > 250 are required, refer application to
factory. Additional ratios are available as standard items. Contact Rexnord for application details.
Example: "VENS 19" requires a Venus size reducer rated for 19,000 lb-in torque.
d = double reduction
t = triple reduction
q = quadruple reduction
qu = quintuple reduction
70
870cfR2.p65
69
Black
7/19/2002, 10:29 AM
DIMENSIONAL DRAWINGS
Reducer Only Mercury & Mars
BC
Mercury
11.75
15.13
M ar s
11.75
15.13
Series
24.38
6.25
4.19
9.41
7/8
25.75
6.25
4.19
9.41
7/8
s,d,t
quad
5.750
22.13
5.750
23.50
bolt
U*
Key
13.13
5.50
9.91
6.59
13.13
6.37
9.91
7.46
quad
3.00
10.88
3.00
10.88
s,d,t
w/ fan
UA*
Key
Avg. Wt.
Lbs
max.
max.
Mercury
7.32
4.50
0.50
2.09
5.75
4.15
2.000
1/2 x 1/2 x 3
3.00
1.88
1.375
5/16 x 5/16 x 2
144
M ar s
7.32
4.50
0.50
2.09
6.25
4.98
2.500
3.50
2.38
1.625
150
71
diminfoR2.p65
70
Black
7/19/2002, 10:37 AM
DIMENSIONAL DRAWINGS
Reducer Only Venus through Jupiter
BC
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
18.00
18.00
23.25
23.25
29.25
29.25
33.00
33.25
33.25
11.75
11.75
11.75
14.00
11.69
19.62
14.75
19.86
28.88
10.500
10.500
13.375
13.375
18.250
18.250
21.625
21.625
28.500
C
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
62.94
Series
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
13.50
13.50
15.94
17.19
20.94
20.94
24.25
24.25
31.50
8.63
9.63
11.38
11.29
18.83
14.37
22.04
18.74
20.88
11.50
11.50
14.38
14.38
19.38
19.38
22.75
22.75
30.00
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
62.94
S
max.
7.28
7.28
11.90
9.14
16.52
13.00
20.02
20.02
26.39
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
16.50
8.00
8.00
9.88
9.88
12.88
12.88
14.63
14.63
14.63
9.53
9.53
9.53
11.75
8.19
16.00
11.00
16.00
12.50
1.25
1.25
2.00
2.00
2.75
2.75
2.75
2.75
2.75
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
1 1/2
2.25
2.25
3.13
3.00
4.00
4.00
5.00
5.88
4.50
2.62
2.62
2.62
2.88
4.00
5.00
5.00
5.93
4.50
s,d,t
9.84
9.84
11.44
11.44
13.16
13.16
14.25
14.25
14.25
1.11
1.11
1.11
1.13
1.75
1.81
1.88
1.93
1.94
quad
8.63
8.63
13.00
13.00
13.06
13.06
16.72
16.72
14.25
X
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
3.50
N
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
12.25
L
s,d,t
13.13
13.13
13.06
15.53
13.43
21.24
16.48
21.58
30.63
Low Speed
U*
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.500
7.250
quad
13.13
13.13
13.13
15.60
13.43
21.24
16.48
21.58
30.63
M
6.76
7.76
9.58
9.33
16.20
11.81
19.30
15.95
18.06
Shaft
Key
5/8 x 5/8 x 4 1/8
3/4 x 3/4 x 5 1/8
7/8 x 7/8 x 5 1/2
1 x 1 x 6 1/2
1 x 1 x 7 1/4
1 1/4 x 1 1/4 x 9 1/4
1 1/4 x 1 1/4 x 9 1/4
1 1/2 x 1 1/2 x 9 1/4
1 3/4 x 1 1/2 x 9 3/4
NA
w/o fan
s,d,t
quad
4.25
3.50
4.25
3.50
4.50
4.25
4.50
4.25
5.68
4.50
5.68
4.50
6.50
5.68
6.50
5.68
6.50
6.50
UA*
w/ fan
s,d,t
2.88
2.88
3.25
2.88
3.56
3.56
4.38
4.38
4.38
quad
2.50
2.50
2.88
2.88
3.25
3.25
3.56
3.56
4.38
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
3.000
Avg. Wt.
Lbs
Key
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
3.000
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
295
325
481
702
923
1146
1512
2000
3470
72
diminfoR2.p65
71
Black
7/19/2002, 10:37 AM
DIMENSIONAL DRAWINGS
Motor Mount Mercury & Mars
Series
AA
BA
Mercury
11.75
12.50
15.13
M ar s
11.75
12.50
15.13
DA
24.38
6.25
13.50
4.19
9.41
7/8
5.75
7.53
9.81
25.75
6.25
13.50
4.19
9.41
7/8
6.25
7.53
9.81
quad
12.50
22.13
12.50
23.50
bolt
QA
ZZ
Mercury
6.59
1.00
0.50
2.09
M ar s
7.46
1.00
0.50
2.09
Motor Frame
182T / 184T
213T / 215T
254T / 256T
Key
Avg. Wt.
Lbs
1.375
5/16 x 5/16 x 2
205
1.625
211
Key
12.00
4.15
2.000
1/2 x 1/2 x 3
3.00
1.88
12.00
4.98
2.500
3.50
2.38
min.
max.
min.
max.
LA
RA
11.41
13.69
11.45
13.73
4.00
0.50
M ar s
11.41
13.69
11.45
13.73
4.50
1.00
Mercury
12.41
14.69
12.45
14.72
4.00
0.13
Series
w/o fan
FA
w/ fan
UA*
FF
M ar s
12.41
14.69
12.45
14.72
4.50
0.63
Mercury
13.16
15.44
13.20
15.47
4.00
-0.50
M ar s
13.16
15.44
13.20
15.47
4.50
0.00
Mercury
14.16
16.44
14.20
16.47
6.25
-0.75
M ar s
14.16
16.44
14.20
16.47
6.75
-0.25
73
72
Black
max.
U*
diminfoR2.p65
min.
Mercury
143T / 145T
HA
PA
s,d,t
7/19/2002, 10:37 AM
DIMENSIONAL DRAWINGS
Motor Mount Venus through Jupiter
AA
BA
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
18.00
18.00
23.25
23.25
29.25
29.25
33.00
33.25
33.25
14.50
14.50
17.00
17.00
22.25
22.25
25.50
25.50
25.50
11.75
11.75
11.75
14.00
11.69
19.62
14.75
19.86
28.88
17.50
17.50
19.50
22.00
20.50
29.50
24.50
29.50
38.50
Series
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
8.63
9.63
11.38
11.29
18.83
14.37
22.04
18.74
20.88
C
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
62.94
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
62.94
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
16.50
8.00
8.00
9.88
9.88
12.88
12.88
14.63
14.63
14.63
9.53
9.53
9.53
11.75
8.19
16.00
11.00
16.00
12.50
1.25
1.25
2.00
2.00
2.75
2.75
2.75
2.75
2.75
Motor
Venus & Atlas
Frame
min. max.
143T/145T 15.47 18.29
182T/184T 16.47 19.29
213T/215T 17.22 20.04
254T/256T 18.22 21.04
284T/286T 18.97 21.79
324T/326T
364T/365T
404T/405T
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
1 1/2
U*
Key
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
12.25
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.500
7.250
2.25
2.25
3.13
3.00
4.00
4.00
5.00
5.88
4.50
2.62
2.62
2.62
2.88
4.00
5.00
5.00
5.93
4.50
LA
s,d,t
5.50
5.50
5.25
5.25
6.50
6.50
6.50
6.50
6.50
PA
quad
4.29
4.29
6.87
6.81
6.39
6.39
8.97
8.97
6.50
min.
11.47
11.47
13.22
13.22
16.72
16.72
17.97
17.97
21.22
max.
14.29
14.29
16.53
16.53
20.52
20.52
21.24
21.24
24.49
w/o fan
s,d,t quad
4.25
3.50
4.25
3.50
4.50
4.25
4.50
4.25
5.68
4.50
5.68
4.50
6.50
5.68
6.50
5.68
6.50
6.50
w/ fan
s,d,t quad
2.88
2.50
2.88
2.50
3.25
2.88
2.88
2.88
3.56
3.25
3.56
3.25
4.38
3.56
4.38
3.56
4.38
4.38
UA*
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
3.000
FA
Earth
Polaris Neptune
Orion
Saturn
Titan
Jupiter Venus & Atlas
min. max. min. max. min. max. min. max. min. max. min. max. min. max. s,d,t quad
2.00
0.79
18.35 21.66 18.35 21.66
1.00
-0.21
19.10 22.41 19.10 22.41 22.60 26.40 22.73 26.53
0.25
20.10 23.41 20.10 23.41 23.60 27.40 23.73 27.53 24.97 28.24 24.97 28.24 28.22 31.49 0.00
20.85 24.16 20.85 24.16 24.35 28.15 24.48 28.28 25.72 28.99 25.72 28.99 28.97 32.22 0.00
21.85 25.16 21.85 25.16 25.35 29.15 25.48 29.28 26.72 29.99 26.72 29.99 29.97 33.22
22.85 26.16 26.35 30.15 26.48 30.28 27.72 30.99 27.72 30.99 30.97 34.22
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
3.000
Avg. Wt.
Lbs
Key
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 5 7/8
3/4 x 3/4 5 7/8
3/4 x 3/4 5 7/8
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
362
392
574
820
1066
1290
1706
2215
3717
RA
Earth
Polaris Neptune
Orion
Saturn
Titan
Jupiter
s,d,t quad s,d,t quad s,d,t quad s,d,t quad s,d,t quad s,d,t quad s,d,t quad
0.00 0.00 0.25 0.14 0.25 0.14 -0.25 2.22 -0.25 2.22 -0.25 -0.25
-0.63 -0.63 0.25 0.25 -0.25 2.22 -0.25 2.22 -0.25 -0.25
-0.50 -0.50 -0.63 -0.63 -0.50 -0.50 1.97 -0.50 -0.50
74
diminfoR2.p65
73
Black
7/19/2002, 10:38 AM
DIMENSIONAL DRAWINGS
Slidebase Mercury & Mars
AA
BA
s,d,t
quad
DA
EA
FA
GA
bolt
PA
min.
Mercury
17.00
12.50
22.13
24.38
6.25
9.63
13.50
10.00
3.38
7/8
3.00
4.00
13.29
4.75
M ar s
17.00
12.50
23.50
25.75
6.25
9.63
13.50
10.00
3.38
7/8
3.00
4.00
13.29
4.75
Series
QA
Mercury
6.30
0.38
M ar s
7.17
0.38
U*
Key
1.25
4.15
2.000
1/2 x 1/2 x 3
3.00
1.88
1.375
5/16 x 5/16 x 2
181
1.25
4.98
2.500
3.50
2.38
1.625
187
w/o fan
w/ fan
UA*
75
diminfoR2.p65
74
Black
7/19/2002, 10:38 AM
Key
Avg. Wt.
Lbs
DIMENSIONAL DRAWINGS
Slidebase Venus through Titan
AA
BA
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
24.00
24.00
30.00
31.00
38.00
38.00
42.00
42.00
13.50
13.50
13.50
17.75
15.00
24.00
18.00
22.00
C
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
DA
EA
FA
GA
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
11.63
11.63
13.25
15.38
17.00
17.00
19.63
19.63
20.00
20.00
25.00
25.00
32.00
32.00
35.00
35.00
11.00
11.00
11.00
15.25
12.00
19.00
14.00
18.00
3.88
3.88
4.50
5.38
5.75
5.75
6.75
6.75
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
0.38
0.38
0.50
0.38
0.75
0.75
0.75
0.75
1.25
1.25
1.25
1.25
1.50
2.50
2.00
2.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
U*
Key
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.500
3.50
3.50
4.00
5.00
5.00
5.00
6.00
6.00
4.50
4.50
5.25
5.38
6.25
6.25
6.50
6.50
17.38
17.38
20.44
22.56
26.69
26.69
31.00
31.00
PA
min.
7.75
7.75
9.88
9.82
12.88
12.88
14.25
14.25
QA
7.90
8.90
10.65
9.54
16.93
12.87
20.54
17.74
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
w/o fan
w/ fan
s,d,t quad s,d,t quad
4.25
3.50
2.88
2.50
4.25
3.50
2.88
2.50
4.50
4.25
3.25
2.88
4.50
4.25
2.88
2.88
5.68
4.50
3.56
3.25
5.68
4.50
3.56
3.25
6.50
5.68
4.38
3.56
6.50
5.68
4.38
3.56
UA*
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
Avg. Wt.
Lbs
Key
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 5 7/8
3/4 x 3/4 5 7/8
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
351
381
578
860
1141
1361
1812
2329
76
diminfoR2.p65
75
Black
7/19/2002, 10:38 AM
DIMENSIONAL DRAWINGS
Baseplate Venus through Jupiter
AA
BA
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
20.00
20.00
25.50
26.50
32.50
32.50
36.50
38.00
40.00
54.00
54.00
58.00
62.00
62.00
70.00
70.00
82.00
90.00
C
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
62.94
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
62.94
CA
DA
DD
EA
FA
GA
60.63
61.63
67.38
71.16
78.33
81.87
89.04
97.74
107.88
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
16.50
13.00
13.00
15.00
17.50
19.00
20.00
22.00
23.00
27.00
8.13
8.13
9.13
10.50
11.75
11.75
13.50
13.50
17.13
8.25
8.25
10.75
11.13
13.50
13.50
15.25
15.50
16.00
25.00
25.00
27.00
28.50
28.50
32.50
32.00
38.00
42.00
4.88
4.88
5.88
7.00
7.25
8.25
8.50
9.50
9.87
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
2.00
2.00
2.00
2.00
2.50
2.50
3.00
3.00
3.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
3.50
U*
Key
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
12.25
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.500
7.250
w/o fan
w/ fan
s,d,t quad s,d,t quad
4.25
3.50
2.88
2.50
4.25
3.50
2.88
2.50
4.50
4.25
3.25
2.88
4.50
4.25
2.88
2.88
5.68
4.50
3.56
3.25
5.68
4.50
3.56
3.25
6.50
5.68
4.38
3.56
6.50
5.68
4.38
3.56
6.50
6.50
4.38
4.38
UA*
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
3.000
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
3.000
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
77
76
Black
QA
3.00
3.00
3.25
3.75
4.25
4.75
4.75
5.25
5.75
18.75
18.75
22.19
24.69
28.69
29.69
33.38
34.38
42.00
8.63
9.63
11.38
11.29
18.83
14.37
22.04
18.74
20.88
0.25
0.25
0.38
0.50
0.50
0.50
0.50
0.63
0.75
Key
diminfoR2.p65
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
1 1/2
7/19/2002, 10:38 AM
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
Avg.
Wt.
Lbs
Motor
Frame
Size Range
474
504
808
1167
1526
1682
2323
3180
5133
324T - 405T
324T - 405T
364T - 444T
364T - 444T
365T - 445T
365T - 445T
404T - 447T
404T - 449T
404T - 449T
DIMENSIONAL DRAWINGS
Scoop Mount Mercury & Mars
Series
Mercury
M ar s
Assy 2
254T - 286T
254T - 324T
AA
BA
CA
s,d,t
quad
DA
EA
FA
GA
bolt
Mercury
15.00
21.00
34.00
42.00
22.13
24.38
38.50
46.50
7.00
9.75
5.75
8.75
15.00
20.00
4.25
7/8
2.25
M ar s
15.00
21.00
34.00
42.00
23.50
25.75
39.37
47.37
7.00
9.75
5.75
8.75
15.00
20.00
4.25
7/8
2.25
Series
QA
U*
Key
Assy 1
Assy 2
Assy 1
Assy 2
Mercury
10.66
13.41
6.75
1.63
2.25
4.15
2.000
1/2 x 1/2 x 3
3.00
1.88
1.375
5/16 x 5/16 x 2
207
280
M ar s
10.66
13.41
7.62
1.63
2.25
4.98
2.500
3.50
2.38
1.625
213
286
78
diminfoR2.p65
77
Black
7/19/2002, 10:39 AM
DIMENSIONAL DRAWINGS
Scoop Mount Venus through Jupiter
Motor Frame Size Range
Series
Venus (s,d,t,q), Atlas (s,d,t,q), Earth(q), Polaris (q)
Earth (s,d,t), Polaris (s,d,t), Neptune (q), Orion (q)
Neptune (s,d,t), Orion (s,d,t), Saturn (q), Titan (q)
Saturn (s,d,t), Titan (s,d,t), Jupiter (s,d,t,q)
Assy 1
143T - 256T
145T - 256T
213T - 286T
254T - 326T
Assy 2
284T - 286T
284T - 326T
324T - 326T
364T - 365T
A
18.00
18.00
23.25
23.25
29.25
29.25
33.00
33.25
33.25
Assy 1
s,d,t
quad
15.25
15.25
15.25
15.25
16.75
15.25
16.75
15.25
23.00
16.75
23.00
16.75
27.25
23.00
27.25
23.00
27.25
27.25
Series
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
8.00
8.00
9.88
9.88
12.88
12.88
14.63
14.63
14.63
9.53
9.53
9.53
11.75
8.19
16.00
11.00
16.00
12.50
1.25
1.25
2.00
2.00
2.75
2.75
2.75
2.75
2.75
Assy 2
s,d,t
quad
17.00
17.00
17.00
17.00
19.00
17.00
19.00
17.00
23.00
19.00
23.00
19.00
27.25
23.00
27.25
23.00
27.25
27.25
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
1 1/2
11.75
11.75
11.75
14.00
11.69
19.62
14.75
19.86
28.88
CA
B
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
62.94
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
62.94
Assy 1
s,d,t
quad
49.89
49.89
50.89
50.89
54.64
55.87
56.86
58.08
65.63
63.25
69.05
66.67
75.28
75.33
77.03
77.08
88.19
88.19
2.25
2.25
3.13
3.00
4.00
4.00
5.00
5.88
4.50
2.62
2.62
2.62
2.88
4.00
5.00
5.00
5.93
4.50
13.50
13.50
15.94
17.19
20.94
20.94
24.25
24.25
31.50
8.63
9.63
11.38
11.29
18.83
14.37
22.04
18.74
20.88
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
3.50
N
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
12.25
s,d,t
52.89
53.89
59.64
61.86
68.63
72.05
78.28
80.03
90.19
Assy 2
quad
52.89
53.89
58.87
61.08
68.25
71.67
78.33
80.08
90.19
D
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
16.50
NA
w/o fan
s,d,t
quad
4.25
3.50
4.25
3.50
4.50
4.25
4.50
4.25
5.68
4.50
5.68
4.50
6.50
5.68
6.50
5.68
6.50
6.50
w/ fan
s,d,t
quad
2.88
2.50
2.88
2.50
3.25
2.88
2.88
2.88
3.56
3.25
3.56
3.25
4.38
3.56
4.38
3.56
4.38
4.38
UA*
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
3.000
Key
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
3.000
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
s = single reduction, d = double reduction, t = triple reduction, quad (q) = quadruple reduction
Add 0.66 w/ Backstop
Contact factory for motor frame sizes other than "T" frame motors
* TOLERANCES: 3.000" Diameter or less +.000/-.001 over 3.000" Diameter +.000/-.002
NOTE: Dimensions subject to change. Certified dimensions of ordered material furnished upon request.
79
diminfoR2.p65
78
Black
7/19/2002, 10:39 AM
Assy 1
381
411
577
836
1094
1316
1745
2233
3703
Assy 2
407
437
620
858
1095
1318
1779
2267
3737
DIMENSIONAL DRAWINGS
Scoop Mount with Slidebase Mercury & Mars
Motor Frame Size Range
Assy 1
143T - 215T
143T - 215T
Series
Mercury
M ar s
Assy 2
254T - 286T
254T - 324T
Series
AA
BA
CA
DA
EA
FA
quad Assy 1 Assy 2 Assy 1 Assy 2 Assy 1 Assy 2 Assy 1 Assy 2 Assy 1 Assy 2
GA
H
bolt
Mercury
20.00
26.00
18.00
23.00
22.13
24.38
38.50
46.50
7.00
9.75
10.38
13.13
16.50
22.50
15.00
20.00
3.38
7/8
3.00
M ar s
20.00
26.00
18.00
23.00
23.50
25.75
39.37
47.37
7.00
9.75
10.38
13.13
16.50
22.50
15.00
20.00
3.38
7/8
3.00
Series
PA
QA
U*
Key
UA*
Key
Avg. Wt.
Lbs
Assy 1 Assy 2
Mercury
4.25
14.04
16.79
6.13
9.13
6.75
0.38
1.50
4.15
2.000
1/2 x 1/2 x 3
3.00
1.88
1.375
5/16 x 5/16 x 2
255
341
M ar s
4.25
14.04
16.79
6.13
9.13
7.62
0.38
1.50
4.98
2.500
3.50
2.38
1.625
261
347
80
diminfoR2.p65
79
Black
7/19/2002, 10:39 AM
DIMENSIONAL DRAWINGS
Scoop Mount with Slidebase Venus through Titan
Motor Frame Size Range
Series
Venus (s,d,t,q), Atlas (s,d,t,q), Earth(q), Polaris (q)
Earth (s,d,t), Polaris (s,d,t), Neptune (q), Orion (q)
Neptune (s,d,t), Orion (s,d,t), Saturn (q), Titan (q)
Saturn (s,d,t), Titan (s,d,t)
Assy 1
143T - 256T
145T - 256T
213T - 286T
254T - 326T
Assy 2
284T - 286T
284T - 326T
324T - 326T
364T - 365T
Assy 1
s,d,t
quad
15.25
15.25
15.25
15.25
16.75
15.25
16.75
15.25
23.00
16.75
23.00
16.75
27.25
23.00
27.25
23.00
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Assy 2
s,d,t
quad
17.00
17.00
17.00
17.00
19.00
17.00
19.00
17.00
23.00
19.00
23.00
19.00
27.25
23.00
27.25
23.00
Series
EA
FA
GA
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
20.00
20.00
25.00
25.00
32.00
32.00
35.00
35.00
11.00
11.00
11.00
15.25
12.00
19.00
14.00
18.00
3.88
3.88
4.50
5.38
5.75
5.75
6.75
6.75
AA
24.00
24.00
30.00
31.00
38.00
38.00
42.00
42.00
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
13.50
13.50
13.50
17.75
15.00
24.00
18.00
22.00
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
3.50
3.50
4.00
5.00
5.00
5.00
6.00
6.00
4.50
4.50
5.25
5.38
6.25
6.25
6.50
6.50
17.38
17.38
20.44
22.56
26.69
26.69
31.00
31.00
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
U*
Key
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.500
Assy 1
s,d,t
quad
49.89
49.89
50.89
50.89
54.64
55.87
56.86
58.08
65.63
63.25
69.05
66.67
75.28
75.33
77.03
77.08
PA
min.
7.75
7.75
9.88
9.82
12.88
12.88
14.25
14.25
80
DA
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
11.63
11.63
13.25
15.38
17.00
17.00
19.63
19.63
QA
0.38
0.38
0.50
0.38
0.75
0.75
0.75
0.75
1.25
1.25
1.25
1.25
1.50
2.50
2.00
2.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
w/o fan
s,d,t quad
4.25
3.50
4.25
3.50
4.50
4.25
4.50
4.25
5.68
4.50
5.68
4.50
6.50
5.68
6.50
5.68
w/ fan
s,d,t quad
2.88
2.50
2.88
2.50
3.25
2.88
2.88
2.88
3.56
3.25
3.56
3.25
4.38
3.56
4.38
3.56
UA*
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
Key
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
81
Black
2
quad
52.89
53.89
58.87
61.08
68.25
71.67
78.33
80.08
7.90
8.90
10.65
9.54
16.93
12.87
20.54
17.74
s = single reduction, d = double reduction, t = triple reduction, quad (q) = quadruple reduction
Add 0.66 w/ Backstop
Contact factory for motor frame sizes other than "T" frame motors listed.
* TOLERANCES: 3.000" Diameter or less +.000/-.001 over 3.000" Diameter +.000/-.002
NOTE: Dimensions subject to change. Certified dimensions of ordered material furnished upon request.
diminfoR2.p65
Assy
s,d,t
52.89
53.89
59.64
61.86
68.63
72.05
78.28
80.03
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
CA
BA
7/19/2002, 10:40 AM
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
Assy 1
437
467
674
993
1312
1531
2045
2562
Assy 2
463
493
717
1015
1313
1533
2079
2596
DIMENSIONAL DRAWINGS
Baseplate with Slidebase Venus through Titan
Motor Frame Size Range
Series
Motor Frame
324T - 405T
Venus
324T - 405T
Atlas
364T - 444T
Earth
364T - 444T
Polaris
364T - 445T
Neptune
364T - 445T
Orion
404T - 447T
Saturn
404T - 449T
Titan
Series
AA
BA
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
26.00
26.00
32.00
33.00
41.00
41.00
45.00
47.00
29.00
29.00
31.00
33.50
33.50
37.50
38.00
44.00
s,d,t
29.73
30.73
34.08
36.30
42.79
46.21
50.03
51.78
quad
28.52
29.52
35.71
37.93
42.69
46.11
52.50
54.25
CA
DA
DD
EA
FA
GA
60.63
61.63
67.38
71.16
78.33
81.87
89.04
97.74
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
16.88
16.88
19.50
22.88
24.75
25.75
28.75
29.75
8.13
8.13
9.13
10.50
11.75
11.75
13.50
13.50
22.00
22.00
27.00
27.00
35.00
35.00
38.00
40.00
25.00
25.00
27.00
29.50
28.50
32.50
32.00
38.00
9.13
9.13
10.75
12.88
13.50
14.50
15.87
16.87
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
0.38
0.38
0.50
0.38
0.75
0.75
0.75
0.75
2.00
2.00
2.00
2.00
2.50
2.50
3.00
3.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
U*
Key
5.50
6.50
7.00
8.00
9.00
10.00
11.00
11.25
2.750
3.250
3.500
4.000
4.500
5.000
5.500
6.500
3.50
3.50
4.00
5.00
5.00
5.00
6.00
6.00
5.25
5.25
5.50
5.63
7.00
7.00
7.00
7.50
22.63
22.63
26.69
30.06
34.44
35.44
40.13
41.13
PA
min.
8.38
8.38
10.75
10.69
14.00
14.00
15.50
16.25
QA
8.63
9.63
11.38
10.79
18.83
14.37
22.04
18.74
H
bolt
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
w/o fan
w/ fan
s,d,t quad s,d,t quad
4.25
3.50
2.88
2.50
4.25
3.50
2.88
2.50
4.50
4.25
3.25
2.88
4.50
4.25
2.88
2.88
5.68
4.50
3.56
3.25
5.68
4.50
3.56
3.25
6.50
5.68
4.38
3.56
6.50
5.68
4.38
3.56
UA*
s,d,t
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
quad
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
Avg. Wt.
Lbs
Key
s,d,t
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
3/4 x 3/4 x 5 7/8
3/4 x 3/4 x 5 7/8
quad
3/8 x 3/8 x 2 1/2
3/8 x 3/8 x 2 1/2
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 3 3/4
1/2 x 1/2 x 4
1/2 x 1/2 x 4
5/8 x 5/8 x 5 1/8
5/8 x 5/8 x 5 1/8
555
585
947
1389
1830
2008
2735
3632
82
diminfoR2.p65
81
Black
7/19/2002, 10:40 AM
DIMENSIONAL DRAWINGS
C-face Reducer Mercury & Mars
BC
H
bolt
s,d,t
quad
Mercury
11.75
15.13
5.750
6.25
4.19
9.41
7/8
3.00
10.38
12.63
5.50
9.91
6.59
M ar s
11.75
15.13
5.750
6.25
4.19
9.41
7/8
3.00
10.38
12.63
6.37
9.91
7.46
max.
max.
Mercury
7.32
M ar s
7.32
Series
Motor Frame
AJ
4.50
0.50
4.50
0.50
AK
BD
HA
2.09
4.15
2.000
1/2 x 1/2 x 3
149
2.09
4.98
2.500
155
WA
Mercury
Key
C
UA
bolt
56C
143TC, 145TC,
182C, 184C
182TC, 184TC,
213C, 215C
213TC, 215TC
quad
s, d, t
quad
5.875
4.50
6.63
3/8
5/8
4.00
19.88
22.13
20.75
23.00
5.875
4.50
6.63
3/8
7/8
4.00
19.88
22.13
20.75
23.00
7.250
8.50
9.00
1/2
1 1/8
4.69
4.50
20.57
22.82
21.44
23.69
7.250
8.50
9.00
1/2
1 3/8
4.69
4.50
20.57
22.82
21.44
23.69
83
82
Black
M ar s
s, d, t
diminfoR2.p65
7/19/2002, 10:40 AM
DIMENSIONAL DRAWINGS
C-face Reducer Venus through Orion
BC
Ve nus
A tla s
Ea rth
Pola ris
Ne ptune
Orion
18.00
18.00
23.25
23.25
29.25
29.25
11.75
11.75
11.75
14.00
11.69
19.62
10.500
10.500
13.375
13.375
18.250
18.250
7.75
7.75
8.75
10.00
11.25
11.25
8.00
8.00
9.88
9.88
12.88
12.88
9.53
9.53
9.53
11.75
8.19
16.00
1.25
1.25
2.00
2.00
2.75
2.75
Series
Venus
Atlas
Earth
Polaris
Neptune
Orion
13.50
13.50
15.94
17.19
20.94
20.94
8.63
9.63
11.38
11.29
19.00
14.37
11.50
11.50
14.38
14.38
19.38
19.38
S
max.
7.28
7.28
11.90
9.14
16.52
13.00
1.11
1.11
1.11
1.13
1.75
1.81
1.00
1.00
1.00
1.00
1.00
1.00
AJ
AK
BD
UA
2.25
2.25
3.13
3.00
4.00
4.00
2.62
2.62
2.62
2.88
4.00
5.00
L
s,d,t
13.19
13.19
14.12
16.59
N
5.50
6.50
7.00
8.00
9.00
10.00
s,d,t
qu a d
15.63
15.63
16.34
18.82
16.12
23.92
6.76
7.76
9.58
9.33
16.20
11.81
WA
quad
Earth &
Polaris
Neptune &
Orion
s,d,t
quad
Earth &
Polaris
Neptune &
Orion
5.875
4.50
6.63
3/8
5/8
Venus &
Atlas
3.38
Venus &
Atlas
3.19
5.875
4.50
6.63
3/8
7/8
4.86
3.38
4.86
4.86
4.67
3.19
4.67
4.67
7.250
8.50
9.00
1/2
1 1/8
5.91
4.06
5.91
5.91
5.72
3.88
5.72
5.72
7.250
7.250
9.000
8.50
8.50
10.50
9.00
9.00
11.00
1/2
1/2
1/2
1 3/8
1 5/8
1 7/8
5.91
5.91
6.06
4.06
5.91
5.91
6.06
5.91
5.91
6.06
5.72
5.72
5.87
3.88
5.72
5.72
5.87
5.72
5.72
5.87
bolt
56C
143TC, 145TC,
182C, 184C
182TC, 184TC
213C, 215C
210T C
250T C
280T C
HA
Motor Frame
H
bolt
1
1
1
1
1 1/4
1 1/4
C
Motor Frame
56C
143TC, 145TC,
182C, 184C
182TC, 184TC,
213C, 215C
210T C
250T C
280T C
Venus
Atlas
Earth
s,d,t
quad
25.77
s,d,t
quad
26.77
s,d,t
quad
s,d,t
Polaris
quad
24.81
25.77
25.81
26.77
28.56
30.78
30.78
33.01
Neptune
s,d,t
quad
40.60
25.86
26.45
26.86
27.45
29.61
31.83
31.83
34.06
38.23
41.64
26.45
26.86
26.86
27.01
27.45
29.61
29.61
29.76
31.83
31.83
31.98
31.83
31.83
31.98
34.06
34.06
34.21
38.23
38.23
38.38
41.64
41.64
41.79
83
Black
37.18
quad
25.86
25.86
26.01
diminfoR2.p65
Orion
s,d,t
7/19/2002, 10:40 AM
84
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
3.53 Nominal Ratio
Single Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
6,000
10,000
18,000
34,000
45,000
85,000
80,000
4,000
8,000
12,000
24,000
44,000
55,000
100,000
100,000
14,000
30,000
54,000
65,000
120,000
16,000
36,000
75,000
42,000
Single Reduction
MARS
VENUS
5,000
10,000
EARTH
20,000
POLARIS
32,000
NEPTUNE
30,000
ORION
90,000
SATURN
90,000
TITAN
JUPITER
4,000
7,000
12,000
24,000
26,000
42,000
40,000
105,000
110,000
14,000
28,000
32,000
52,000
50,000
130,000
16,000
38,000
60,000
44,000
70,000
80,000
Single Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000
5,000
11,000
18,000
34,000
35,000
100,000
3,000
7,000
13,000
22,000
40,000
45,000
120,000
15,000
26,000
46,000
55,000
140,000
17,000
30,000
65,000
75,000
85,000
Double Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
14,000
32,000
44,000
70,000
JUPITER
18,000
38,000
54,000
80,000
22,000
44,000
64,000
90,000
26,000
50,000
100,000
110,000
Double Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000
6,000
13,000
24,000
42,000
50,000
80,000
110,000
150,000
210,000
3,000
8,000
15,000
28,000
48,000
60,000
90,000
125,000
165,000
250,000
5,000
10,000
17,000
32,000
54,000
70,000
100,000
140,000
180,000
19,000
36,000
60,000
80,000
110,000
21,000
85
tech infoR2.p65
84
Black
7/19/2002, 10:57 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
Double Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
8,000
14,000
26,000
40,000
65,000
85,000
120,000
160,000
220,000
300,000
4,000
10,000
16,000
30,000
46,000
75,000
95,000
135,000
175,000
260,000
330,000
6,000
12,000
18,000
34,000
52,000
85,000
105,000
150,000
190,000
20,000
38,000
58,000
115,000
22,000
64,000
Double Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
7,000
15,000
22,000
40,000
65,000
90,000
130,000
160,000
200,000
4,000
9,000
17,000
26,000
46,000
75,000
100,000
140,000
175,000
240,000
6,000
11,000
19,000
30,000
52,000
85,000
110,000
150,000
190,000
280,000
13,000
21,000
34,000
58,000
120,000
320,000
38,000
64,000
Double Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
8,000
15,000
26,000
40,000
80,000
110,000
140,000
170,000
240,000
300,000
4,000
10,000
17,000
30,000
46,000
90,000
120,000
150,000
190,000
280,000
350,000
6,000
12,000
19,000
34,000
52,000
100,000
130,000
160,000
210,000
400,000
21,000
38,000
58,000
450,000
23,000
64,000
70,000
Double Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000
8,000
16,000
26,000
42,000
70,000
95,000
140,000
180,000
230,000
300,000
3,000
10,000
18,000
30,000
48,000
80,000
105,000
155,000
195,000
270,000
350,000
5,000
12,000
20,000
34,000
54,000
90,000
115,000
170,000
210,000
310,000
400,000
7,000
14,000
22,000
38,000
60,000
125,000
350,000
450,000
66,000
135,000
3 1 .6 3 Nomina l R a tio
MER CURY
MA R S
VENUS
ATLA S
EA RTH
P O L A R IS
NEPTUNE
OR ION
SATUR N
TITA N
JUPITER
2,000d
7,000d
15,000d
20,000d
38,000d
70,000t
90,000d
155,000t
200,000d
280,000d
400,000d
4,000d
9,000d
17,000d
24,000d
44,000d
80,000t
100,000d
170,000t
220,000d
320,000d
450,000d
6,000d
11,000d
19,000d
28,000d
50,000d
110,000d
360,000d
500,000d
13,000d
32,000d
56,000d
120,000d
34,000t
60,000t
130,000t
38,000t
66,000t
140,000t
150,000t
86
tech infoR2.p65
85
Black
7/19/2002, 10:57 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000t
9,000t
17,000t
25,000t
46,000t
80,000t
110,000t
170,000t
220,000t
280,000t
300,000d
3,000t
11,000t
19,000t
29,000t
52,000t
90,000t
120,000t
185,000t
235,000t
320,000t
350,000d
5,000t
7,000t
13,000t
15,000t
21,000t
23,000t
33,000t
37,000t
41,000t
58,000t
64,000t
70,000t
100,000t
110,000t
130,000t
140,000t
150,000t
200,000t
250,000t
360,000t
400,000d
450,000d
500,000d
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000d
8,000d
18,000t
25,000t
42,000t
75,000t
120,000t
175,000t
230,000t
300,000t
500,000t
3,000d
10,000d
20,000t
29,000t
48,000t
85,000t
130,000t
200,000t
245,000t
340,000t
550,000t
5,000d
12,000t
22,000t
33,000t
54,000t
95,000t
140,000t
225,000t
260,000t
380,000t
600,000t
7,000t
14,000t
24,000t
37,000t
60,000t
105,000t
150,000t
16,000t
41,000t
66,000t
115,000t
72,000t
Triple Reduction
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
26,000
48,000
80,000
130,000
180,000
240,000
280,000
450,000
4,000
11,000
20,000
30,000
54,000
90,000
140,000
195,000
255,000
320,000
500,000
6,000
13,000
22,000
34,000
60,000
100,000
150,000
210,000
270,000
360,000
550,000
8,000
15,000
24,000
38,000
66,000
110,000
400,000
600,000
17,000
42,000
72,000
120,000
MERCURY
Triple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
26,000
48,000
80,000
125,000
180,000
240,000
300,000
450,000
4,000
11,000
20,000
30,000
54,000
90,000
135,000
205,000
255,000
340,000
500,000
6,000
13,000
22,000
34,000
60,000
100,000
145,000
230,000
270,000
380,000
550,000
8,000
15,000
24,000
38,000
66,000
110,000
155,000
420,000
600,000
17,000
42,000
72,000
120,000
650,000
Triple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000
9,000
18,000
23,000
44,000
75,000
115,000
180,000
240,000
320,000
450,000
3,000
11,000
20,000
27,000
50,000
85,000
125,000
205,000
260,000
360,000
500,000
5,000
13,000
22,000
31,000
56,000
95,000
135,000
230,000
280,000
400,000
550,000
7,000
15,000
35,000
62,000
105,000
145,000
600,000
17,000
39,000
68,000
640,000
87
tech infoR2.p65
86
Black
7/19/2002, 10:58 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
Triple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
26,000
44,000
80,000
130,000
190,000
240,000
310,000
450,000
4,000
11,000
20,000
30,000
50,000
90,000
140,000
205,000
270,000
350,000
500,000
6,000
13,000
22,000
34,000
56,000
100,000
150,000
220,000
300,000
390,000
550,000
8,000
15,000
24,000
38,000
62,000
110,000
160,000
430,000
600,000
17,000
42,000
68,000
120,000
650,000
74,000
9 1 .4 1 Nomina l R a tio
Triple Reduction
MER CURY
MA R S
VENUS
ATLA S
EA RTH
P O L A R IS
NEPTUNE
OR ION
SATUR N
TITA N
JUPITER
2,000
9,000
22,000
42,000
80,000
180,000
300,000
4,000
11,000
26,000
48,000
90,000
210,000
350,000
6,000
13,000
30,000
54,000
100,000
240,000
400,000
8,000
15,000
34,000
110,000
260,000
450,000
17,000
38,000
120,000
500,000
130,000
550,000
600,000
650,000
Triple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000
9,000
17,000
24,000
46,000
75,000
115,000
190,000
250,000
300,000
450,000
3,000
11,000
19,000
28,000
52,000
85,000
125,000
215,000
265,000
340,000
500,000
5,000
13,000
21,000
32,000
58,000
95,000
135,000
240,000
280,000
380,000
7,000
15,000
23,000
36,000
64,000
105,000
145,000
420,000
40,000
70,000
Triple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
26,000
44,000
80,000
130,000
190,000
240,000
320,000
450,000
4,000
11,000
20,000
30,000
50,000
90,000
140,000
205,000
270,000
360,000
500,000
6,000
13,000
22,000
34,000
56,000
100,000
150,000
220,000
300,000
400,000
550,000
8,000
15,000
24,000
38,000
62,000
110,000
160,000
440,000
600,000
17,000
42,000
68,000
120,000
650,000
74,000
1 2 1 .4 Nomina l R a tio
MER CURY
MA R S
VENUS
ATLA S
EA RTH
P O L A R IS
NEPTUNE
OR ION
SATUR N
TITA N
JUPITER
1,000q
9,000q
22,000q
44,000q
80,000q
130,000q
180,000q
260,000q
320,000q
450,000t
3,000q
11,000q
26,000q
50,000q
90,000q
140,000q
205,000q
280,000q
360,000q
500,000t
5,000q
13,000q
30,000q
56,000q
100,000q
150,000q
230,000q
300,000q
400,000q
550,000t
7,000q
15,000q
34,000q
62,000q
110,000q
160,000q
440,000q
600,000t
17,000q
38,000q
68,000q
120,000q
650,000t
74,000q
tech infoR2.p65
87
Black
88
7/19/2002, 10:58 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000t
9,000t
17,000t
27,000t
46,000t
80,000t
120,000t
190,000t
250,000t
300,000t
450,000t
3,000t
11,000t
19,000t
31,000t
52,000t
90,000t
130,000t
215,000t
265,000t
340,000t
500,000t
5,000t
13,000t
21,000t
35,000t
58,000t
100,000t
140,000t
240,000t
280,000t
380,000t
7,000t
15,000t
23,000t
39,000t
64,000t
110,000t
150,000t
420,000t
24,000q
43,000q
70,000t
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000t
9,000t
18,000q
27,000q
44,000q
80,000q
130,000q
190,000q
260,000q
320,000q
450,000t
4,000t
11,000t
20,000q
31,000q
50,000q
90,000q
140,000q
215,000q
280,000q
360,000q
500,000t
6,000t
13,000t
22,000q
35,000q
56,000q
100,000q
150,000q
240,000q
300,000q
400,000q
550,000t
8,000t
15,000t
24,000q
39,000q
62,000q
110,000q
160,000q
440,000q
600,000t
17,000t
43,000q
68,000q
120,000q
650,000t
74,000q
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000t
9,000t
16,000t
21,000t
36,000t
80,000q
130,000t
190,000q
230,000t
320,000q
450,000t
3,000t
11,000t
18,000t
25,000t
42,000t
90,000q
140,000q
215,000q
260,000q
360,000q
500,000t
5,000t
13,000t
20,000t
29,000t
48,000t
100,000q
150,000q
240,000q
280,000q
400,000q
7,000t
15,000t
33,000t
54,000t
110,000q
160,000q
300,000q
440,000q
60,000t
120,000q
64,000q
70,000q
76,000q
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
27,000
46,000
80,000
130,000
190,000
260,000
320,000
450,000
4,000
11,000
20,000
31,000
52,000
90,000
140,000
215,000
280,000
360,000
500,000
6,000
13,000
22,000
35,000
58,000
100,000
150,000
240,000
300,000
400,000
550,000
8,000
15,000
24,000
39,000
64,000
110,000
160,000
440,000
600,000
17,000
43,000
70,000
120,000
650,000
76,000
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
27,000
46,000
80,000
130,000
180,000
260,000
320,000
550,000
4,000
11,000
20,000
31,000
52,000
90,000
140,000
205,000
280,000
360,000
600,000
6,000
13,000
22,000
35,000
58,000
100,000
150,000
230,000
300,000
400,000
650,000
8,000
15,000
24,000
39,000
64,000
110,000
160,000
440,000
17,000
43,000
70,000
120,000
76,000
89
tech infoR2.p65
88
Black
7/19/2002, 10:59 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000t
8,000t
18,000q
27,000q
46,000q
80,000q
130,000q
190,000q
260,000q
320,000q
450,000q
3,000t
10,000t
20,000q
31,000q
52,000q
90,000q
140,000q
215,000q
280,000q
360,000q
500,000q
5,000t
13,000q
22,000q
35,000q
58,000q
100,000q
150,000q
240,000q
300,000q
400,000q
550,000q
7,000q
15,000q
24,000q
39,000q
64,000q
110,000q
160,000q
440,000q
600,000q
17,000q
43,000q
70,000q
120,000q
650,000q
76,000q
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
9,000
18,000
27,000
48,000
75,000
120,000
190,000
250,000
300,000
450,000
4,000
11,000
20,000
31,000
54,000
85,000
130,000
215,000
265,000
340,000
500,000
6,000
13,000
22,000
35,000
60,000
95,000
140,000
240,000
280,000
380,000
550,000
8,000
15,000
24,000
39,000
66,000
105,000
150,000
420,000
600,000
17,000
43,000
72,000
115,000
650,000
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
10,000
19,000
24,000
46,000
80,000
130,000
180,000
260,000
320,000
450,000
4,000
12,000
21,000
28,000
52,000
90,000
140,000
205,000
280,000
360,000
500,000
6,000
14,000
23,000
32,000
58,000
100,000
150,000
230,000
300,000
400,000
550,000
8,000
16,000
36,000
64,000
110,000
160,000
440,000
600,000
18,000
40,000
70,000
120,000
650,000
76,000
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
10,000
20,000
27,000
46,000
80,000
130,000
190,000
260,000
320,000
450,000
4,000
12,000
22,000
31,000
52,000
90,000
140,000
215,000
280,000
360,000
500,000
6,000
14,000
24,000
35,000
58,000
100,000
150,000
240,000
300,000
400,000
550,000
8,000
16,000
39,000
64,000
110,000
160,000
440,000
600,000
18,000
43,000
70,000
120,000
650,000
76,000
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
10,000
20,000
27,000
48,000
75,000
125,000
190,000
250,000
310,000
450,000
4,000
12,000
22,000
31,000
54,000
85,000
135,000
215,000
265,000
350,000
500,000
6,000
14,000
24,000
35,000
60,000
95,000
145,000
240,000
280,000
390,000
550,000
8,000
16,000
39,000
66,000
105,000
155,000
430,000
600,000
18,000
43,000
72,000
115,000
650,000
90
tech infoR2.p65
89
Black
7/19/2002, 10:59 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000
8,000
17,000
24,000
46,000
80,000
130,000
180,000
260,000
320,000
450,000
3,000
10,000
19,000
28,000
52,000
90,000
140,000
205,000
280,000
360,000
500,000
5,000
12,000
21,000
32,000
58,000
100,000
150,000
230,000
300,000
400,000
550,000
7,000
14,000
23,000
36,000
64,000
110,000
160,000
440,000
600,000
16,000
40,000
70,000
120,000
650,000
76,000
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
10,000
20,000
27,000
48,000
75,000
125,000
190,000
250,000
310,000
450,000
4,000
12,000
22,000
31,000
54,000
85,000
135,000
215,000
265,000
350,000
500,000
6,000
14,000
24,000
35,000
60,000
95,000
145,000
240,000
280,000
390,000
550,000
8,000
16,000
39,000
66,000
105,000
155,000
430,000
600,000
18,000
43,000
72,000
115,000
650,000
Quadruple Reduction
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000
10,000
19,000
24,000
46,000
80,000
130,000
190,000
260,000
320,000
450,000
4,000
12,000
21,000
28,000
52,000
90,000
140,000
215,000
280,000
360,000
500,000
6,000
14,000
23,000
32,000
58,000
100,000
150,000
240,000
300,000
400,000
550,000
8,000
16,000
36,000
64,000
110,000
160,000
440,000
600,000
18,000
40,000
70,000
120,000
650,000
76,000
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000q
8,000q
30,000qu
70,000qu
130,000qu
190,000qu
260,000qu
320,000qu
450,000q
3,000q
10,000q
36,000qu
80,000qu
140,000qu
215,000qu
280,000qu
360,000qu
500,000q
5,000q
12,000q
42,000qu
90,000qu
150,000qu
240,000qu
300,000qu
400,000qu
550,000q
7,000q
14,000q
48,000qu
100,000qu
160,000qu
440,000qu
16,000q
54,000qu
110,000qu
120,000qu
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000q
10,000q
20,000q
27,000q
48,000q
75,000q
125,000q
190,000q
250,000q
310,000q
450,000qu
4,000q
12,000q
22,000q
31,000q
54,000q
85,000q
135,000q
215,000q
265,000q
350,000q
500,000qu
6,000q
14,000q
24,000q
35,000q
60,000q
95,000q
145,000q
240,000q
280,000q
390,000q
550,000qu
8,000q
16,000q
39,000q
66,000q
105,000q
155,000q
430,000q
18,000q
43,000q
72,000q
115,000q
91
tech infoR2.p65
90
Black
7/19/2002, 10:59 AM
TECHNICAL INFORMATION
Low Speed Shaft Torque Ratings
TABLE 5
Reducer Only Selection*
Low Speed Shaft Torque Ratings (lb-in)
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000q
8,000q
17,000q
24,000q
42,000qu
65,000qu
120,000qu
190,000qu
260,000qu
320,000qu
450,000q
3,000q
10,000q
19,000q
28,000q
48,000qu
75,000qu
130,000qu
215,000qu
280,000qu
360,000qu
500,000q
5,000q
12,000q
21,000q
32,000q
54,000qu
85,000qu
140,000qu
240,000qu
300,000qu
400,000qu
550,000q
7,000q
14,000q
23,000q
36,000q
95,000qu
150,000qu
440,000qu
600,000q
16,000q
40,000q
105,000qu
160,000qu
650,000q
115,000qu
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000q
10,000q
20,000q
21,000q
36,000q
70,000qu
130,000q
190,000qu
260,000qu
280,000qu
450,000qu
4,000q
12,000q
25,000q
42,000q
80,000qu
215,000qu
280,000qu
320,000qu
500,000qu
6,000q
14,000q
29,000q
48,000q
90,000qu
240,000qu
300,000qu
360,000qu
550,000qu
8,000q
16,000q
33,000q
54,000q
100,000qu
400,000qu
600,000qu
18,000q
60,000q
110,000qu
440,000qu
650,000qu
120,000qu
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
1,000q
8,000q
18,000q
21,000q
36,000qu
65,000qu
120,000qu
190,000qu
260,000qu
320,000qu
450,000qu
3,000q
10,000q
20,000q
25,000q
42,000qu
75,000qu
130,000qu
215,000qu
280,000qu
360,000qu
500,000qu
5,000q
12,000q
29,000q
48,000qu
85,000qu
140,000qu
240,000qu
300,000qu
400,000qu
550,000qu
7,000q
14,000q
33,000q
54,000qu
95,000qu
150,000qu
440,000qu
600,000qu
16,000q
105,000qu
160,000qu
650,000qu
115,000qu
MERCURY
MARS
VENUS
ATLAS
EARTH
POLARIS
NEPTUNE
ORION
SATURN
TITAN
JUPITER
2,000q
8,000q
30,000qu
65,000qu
120,000qu
190,000qu
260,000qu
320,000qu
450,000qu
4,000q
10,000q
36,000qu
75,000qu
130,000qu
215,000qu
280,000qu
360,000qu
500,000qu
6,000q
42,000qu
85,000qu
140,000qu
240,000qu
300,000qu
400,000qu
550,000qu
48,000qu
95,000qu
150,000qu
440,000qu
600,000qu
54,000qu
105,000qu
160,000qu
650,000qu
115,000qu
92
tech infoR2.p65
91
Black
7/19/2002, 11:00 AM
TECHNICAL INFORMATION
Maximum Mechanical Input HP Ratings at 1750 RPM
TABLE 6
R e duc tion
Single
Nomina l
R a tio
Me rc ury
Ma rs
Ve nus
3 .5 3
30.38
60.75
137.25
4 .3 9
24.39
42.69
110.87
6 .1 2
13.14
30.67
84.34
80.36
154.54
197.82
9 .3 0
Double
E a rt h
Pola ris
Ne ptune
Orion
S a t u rn
360.27
463.21
643.34
857.79
1029.35
194.02
304.88
360.31
554.33
727.56
900.79
148.84
228.23
Jupite r
694.60
340.00
1 1 .0 2
14.26
28.52
55.66
95.42
159.03
212.04
291.56
371.08
477.10
662.64
12.46
24.93
47.04
81.25
136.85
181.75
245.90
320.74
406.27
555.95
1 7 .2 1
10.01
21.70
36.23
65.56
110.42
146.65
207.03
258.79
327.80
552.09
753.04
2 0 .4 1
8.05
16.09
35.27
58.26
107.33
153.33
199.33
245.32
321.99
429.32
688.89
2 4 .0 0
8.39
16.77
27.22
47.01
81.65
111.34
167.01
210.31
259.80
433.00
532.36
3 1 .6 3
5.78
12.52
16.85
28.38
49.66
195.08
344.76
511.54
4 3 .7 8
3.46
6.91
36.29
63.03
76.40
143.25
162.35
3 6 .5 6
5.46
11.70
18.84
33.59
57.34
90.11
122.88
163.84
204.80
294.91
424.18d
4 3 .7 8
4.84
11.06
15.86
27.10
47.58
77.00
99.13
148.70
171.83
251.14
423.03
5 4 .4 5
4.55
9.66
12.80
22.40
38.39
58.66
79.99
111.98
143.98
213.30
351.89
6 4 .4 2
3.65
7.76
11.37
19.90
34.11
52.12
73.44
108.97
127.92
198.99
307.58
6 9 .6 3
3.01
7.31
9.46
16.78
29.25
45.17
62.38
98.94
120.45
172.07
293.66
9.17
43.96
61.16
84.10
114.68
164.37
248.12
8 0 .0 1
2.93
6.24
9 1 .4 1
2.62
5.57
9 9 .3 8
2.06
4.42
1 1 1 .5
2.11
4.48
106.41
16.06
28.29
12.14
17.25
7.09
12.33
21.59
32.38
44.71
74.01
86.34
129.51
147.49
6.58
11.51
20.28
31.51
43.85
60.29
82.21
120.58
177.86
18.73
29.11
40.51
58.23
75.95
111.39
153.27
8.62
15.48
24.32
33.16
53.06
61.90
92.85
105.73
23.49q
32.68q
49.02q
61.27q
89.87q
127.51
36.45
72.50
75.79
1 2 1 .4
1.75
4.25
1 3 8 .5
1.48
3.17
5.08
5.38
9.64
1 5 9 .8
1.51
3.21
4.32q
7.74q
15.11q
1 9 3 .1
1.06
2.28
3.17
5.23
9.51
1 9 3 .1
Qua d
421.72
Tita n
1 3 .8 5
3 1 .6 3
Triple
A tla s
12.52
41.52
85.87
20.60
18.95
26.36
39.54
220.48
49.43
2 0 6 .2
1.24
2.64
3.49
6.25
11.13
16.84
23.43
35.14
43.92
64.42
95.04
2 3 8 .2
1.00
2.12
3.10
5.56
10.10
15.29
21.27
30.57
39.88
58.49
81.90
2 6 5 .4
0.55t
1.09t
2.81
5.04
8.98
13.58
18.90
28.35
35.44
51.97
76.67
0.82
2.00
2 9 5 .7
0.80
1.71
2.50
4.48
7.72
11.80
16.08
25.74
30.02
45.04
68.13
3 3 0 .1
0.72
1.61
2.17
3.78
7.24
10.96
15.25
21.92
28.59
41.93
61.85
3 6 9 .8
0.64
1.45
2.02
3.62
6.44
9.74
13.55
20.32
25.40
37.26
54.96
4 1 2 .1
0.58
1.30
1.79
3.21
5.53
8.46
11.92
18.45
21.52
33.06
53.30
4 5 9 .0
0.45
1.04
1.56
2.71
5.19
7.86
10.93
15.71
20.49
30.06
44.34
5 3 2 .5
0.46
1.04
1.45
2.59
3.97
6.06
8.54
13.23
15.43
23.70
39.40
6 1 7 .9
0.41
0.93
1.12
1.95
3.72
5.63
7.84
11.75
14.69
21.55
31.79
6 6 0 .6
0.33
0.74
2.51q u
5.35q u
7.66q u
10.86q u
14.36q u
21.07q u
25.76
7 4 1 .2
0.33
0.75
1.04
1.86
2.84
4.35
6.12
9.48
11.06
16.99
23.80q u
9 0 0 .3
0.23
0.53
0.80
1.40
1.84q u
3.75q u
5.49q u
8.76q u
10.30q u
15.10q u
22.79
1057
0.24
0.54
0.57
0.94
1.70
3.49q u
3.68
7.07q u
9.15q u
13.42q u
19.11q u
1255
0.17
0.38
0.50
0.83
1.32q u
2.69q u
3.94q u
6.28q u
7.38q u
10.83q u
16.47q u
1785
0.10
0.17
0.95q u
1.93q u
2.82q u
4.09q u
5.29q u
7.76q u
11.81q u
93
tech infoR2.p65
92
Black
7/19/2002, 11:00 AM
TECHNICAL INFORMATION
Maximum Mechanical Input HP Ratings at 1430 RPM
TABLE 6
R e duc tion
Single
Nomina l
R a tio
Me rc ury
Ma rs
Ve nus
3 .5 3
24.82
49.65
112.15
Ne ptune
Orion
S a t u rn
378.51
525.70
700.94
841.13
294.43
452.97
594.52
Tita n
Jupite r
19.93
34.88
90.59
158.54
249.13
10.74
25.06
68.92
121.63
186.49
65.67
126.29
161.64
277.83
1 1 .0 2
11.65
23.31
45.48
77.97
129.95
173.27
238.25
303.22
389.86
1 3 .8 5
10.19
20.37
38.44
66.40
111.83
148.52
200.94
269.02
331.98
454.29
1 7 .2 1
8.18
17.73
29.61
53.57
90.23
119.83
169.18
211.47
267.86
451.14
2 0 .4 1
6.58
13.15
28.82
47.61
87.70
125.29
162.88
200.47
263.11
350.81
562.92
2 4 .0 0
6.85
13.71
22.24
38.42
66.72
90.98
136.47
171.86
212.29
353.82
435.02
3 1 .6 3
4.72
10.23
13.77
23.19
40.58
159.41
281.72
418.01
4 3 .7 8
2.82
5.65
29.65
51.50
62.43
117.05
132.66
3 6 .5 6
4.46
9.56
15.4
27.45
46.86
73.63
100.41
133.88
167.35
240.98
346.61d
4 3 .7 8
3.95
9.04
12.96
22.14
38.88
59.4
81.01
121.51
140.41
205.21
345.68
5 4 .4 5
3.71
7.89
10.46
18.30
31.37
47.93
65.36
91.51
117.65
174.30
287.55
344.61
736.07
567.59
86.95
541.47
615.34
6 4 .4 2
2.98
6.34
9.29
16.26
27.88
42.59
60.01
89.05
104.53
162.61
251.33
6 9 .6 3
2.46
5.97
7.73
13.71
23.90
36.91
50.97
80.85
98.43
140.61
239.96
7.50
13.12
23.11
35.92
49.98
68.72
93.71
134.32
202.75
9.92
14.09
105.83
120.52
8 0 .0 1
2.40
5.10
9 1 .4 1
2.14
4.55
9 9 .3 8
1.69
3.61
5.80
10.08
17.64
5.37
9.41
16.57
25.75
35.83
49.26
67.18
98.53
145.34
15.31
23.79
33.10
47.58
62.06
91.02
125.24
12.65
19.87
27.10
43.36
50.58
75.87
86.4
19.19q
26.70q
40.05q
50.07q
73.43q
104.2
29.79
59.24
61.93
77.66
1 1 1 .5
1.72
3.66
1 2 1 .4
1.43
3.47
1 3 8 .5
1.21
2.59
4.15
7.05
4.39
7.87
33.93
26.46
36.54
70.17
60.48
70.55
180.16
1 5 9 .8
1.24
2.63
3.53q
6.33q
12.35q
1 9 3 .1
0.87
1.86
2.59
4.27
7.77
10.23
15.48
21.54
32.31
40.39
2 0 6 .2
1.02
2.16
2.85
5.10
9.09
13.76
19.14
28.71
35.89
52.64
2 3 8 .2
0.82
1.73
2.54
4.54
8.25
12.49
17.38
24.98
32.58
47.79
66.92
2 6 5 .4
0.45t
0.89t
2.30
4.12
7.34
11.10
15.44
23.16
28.96
42.47
62.65
1 9 3 .1
Qua d
Pola ris
294.39
4 .3 9
3 1 .6 3
Triple
Ea rth
6 .1 2
9 .3 0
Double
A tla s
16.84
0.67
1.63
2 9 5 .7
0.66
1.39
2.05
3.66
6.31
9.64
13.14
21.03
24.53
36.80
55.67
3 3 0 .1
0.59
1.32
1.78
3.09
5.92
8.95
12.46
17.91
23.36
34.26
50.54
3 6 9 .8
0.53
1.19
1.65
2.96
5.26
7.96
11.07
16.61
20.76
30.44
44.91
4 1 2 .1
0.47
1.06
1.47
2.63
4.52
6.91
9.74
15.08
17.59
27.01
43.55
36.23
4 5 9 .0
0.37
0.85
1.28
2.22
4.24
6.42
8.93
12.84
16.75
24.56
5 3 2 .5
0.38
0.85
1.18
2.12
3.24
4.95
6.98
10.81
12.61
19.36
32.2
6 1 7 .9
0.34
0.76
0.91
1.59
3.04
4.60
6.40
9.60
12.00
17.61
25.97
2.05q u
4.38q u
6.26q u
8.87q u
11.74q u
17.21q u
21.05
1.52
2.32
3.55
5.00
7.75
9.04
13.88
19.45q u
6 6 0 .6
0.27
0.61
7 4 1 .2
0.27
0.61
0.85
9 0 0 .3
0.19
0.44
0.66
1.14
1.50q u
3.06q u
4.49q u
7.16q u
8.41q u
12.34q u
18.62
1057
0.20
0.44
0.46
0.77
1.39
2.85q u
3.01
5.77q u
7.48q u
10.97q u
15.62q u
1255
0.14
0.31
0.41
0.67
1.08q u
2.20q u
3.22q u
5.13q u
6.03q u
8.85q u
13.46q u
1785
0.08
0.14
0.77q u
1.58q u
2.31q u
3.34q u
4.32q u
6.34q u
9.65q u
94
tech infoR2.p65
93
Black
7/19/2002, 11:00 AM
TECHNICAL INFORMATION
Maximum Mechanical Input HP Ratings at 1170 RPM
TABLE 6
R e duc tion
Single
Nomina l
R a tio
Me rc ury
Ma rs
Ve nus
3 .5 3
20.31
40.62
91.76
4 .3 9
16.31
28.54
74.12
6 .1 2
8.79
20.50
56.39
53.73
103.32
132.25
227.31
1 1 .0 2
9.54
19.07
37.21
63.79
106.32
141.77
194.93
248.09
318.97
443.02
1 3 .8 5
8.33
16.67
31.45
54.32
91.49
121.52
164.40
214.44
271.62
371.69
1 7 .2 1
6.70
14.51
24.22
43.83
73.82
98.05
138.42
173.02
219.16
369.11
9 .3 0
Double
E a rt h
Pola ris
Ne ptune
Orion
S a t u rn
240.87
309.69
430.12
573.50
688.20
129.71
203.84
240.90
370.61
486.42
99.51
152.59
Jupite r
602.24
464.39
503.46
2 0 .4 1
5.38
10.76
23.58
38.95
71.76
102.51
133.26
164.02
215.27
287.03
460.57
5.61
11.21
18.20
31.43
54.59
74.44
111.66
140.61
173.69
289.49
355.92
3 1 .6 3
3.86
8.37
11.26
18.97
33.20
130.43
230.50
342.00
4 3 .7 8
2.31
4.62
24.26
42.14
51.08
95.77
108.54
3 6 .5 6
3.65
7.82
12.60
22.46
38.34
60.25
82.15
109.54
136.92
197.17
283.59d
4 3 .7 8
3.24
7.40
10.60
18.12
31.81
48.60
66.28
99.42
114.88
167.90
282.83
5 4 .4 5
3.04
6.46
8.56
14.97
25.67
39.22
53.48
74.87
96.26
142.61
235.27
205.64
71.14
6 4 .4 2
2.44
5.19
7.60
13.30
22.81
34.84
49.10
72.86
85.53
133.04
6 9 .6 3
2.01
4.89
6.33
11.22
19.56
30.20
41.70
66.15
80.53
115.04
196.33
8 0 .0 1
1.96
4.17
6.13
10.73
18.91
29.39
40.89
56.23
76.67
109.89
165.89
9 1 .4 1
1.75
3.72
8.11
11.53
9 9 .3 8
1.38
2.96
4.74
8.25
14.43
21.65
29.89
49.48
57.73
86.59
98.61
1 1 1 .5
1.41
2.99
4.40
7.70
13.56
21.07
29.31
40.31
54.96
80.61
118.92
1 2 1 .4
1.17
2.84
12.52
19.46
27.08
38.93
50.78
74.47
102.47
1 3 8 .5
0.99
2.12
3.40
5.76
10.35
16.26
22.17
35.47
41.39
62.08
70.69
3.60
6.44
15.70q
21.85q
32.77q
40.96q
60.08q
85.25q
24.37
48.47
50.67
63.54
1 5 9 .8
1.01
2.15
2.89q
5.18q
10.10q
1 9 3 .1
0.71
1.52
2.12
3.50
6.36
1 9 3 .1
Qua d
281.95
Tita n
2 4 .0 0
3 1 .6 3
Triple
A tla s
8.37
27.76
57.41
13.77
12.67
17.63
26.44
33.05
147.41
2 0 6 .2
0.83
1.77
2.33
4.18
7.44
11.26
15.66
23.49
29.37
43.07
2 3 8 .2
0.67
1.42
2.07
3.72
6.75
10.22
14.22
20.44
26.66
39.10
54.75
2 6 5 .4
0.36t
0.73t
1.88
3.37
6.00
9.08
12.64
18.95
23.69
34.75
51.26
0.55
1.34
2 9 5 .7
0.54
1.14
1.67
3.00
5.16
7.89
10.75
17.21
20.07
30.11
45.55
3 3 0 .1
0.48
1.08
1.45
2.53
4.84
7.33
10.19
14.65
19.11
28.03
41.35
3 6 9 .8
0.43
0.97
1.35
2.42
4.30
6.51
9.06
13.59
16.98
24.91
36.75
4 1 2 .1
0.39
0.87
1.20
2.15
3.70
5.65
7.97
12.33
14.39
22.10
35.63
29.65
4 5 9 .0
0.30
0.69
1.04
1.82
3.47
5.25
7.31
10.50
13.70
20.10
5 3 2 .5
0.31
0.70
0.97
1.73
2.65
4.05
5.71
8.84
10.32
15.84
26.34
6 1 7 .9
0.28
0.62
0.75
1.30
2.49
3.77
5.24
7.86
9.82
14.41
21.25
6 6 0 .6
0.22
0.50
1.68q u
3.58q u
5.12q u
7.26q u
9.60q u
14.08q u
17.22
7 4 1 .2
0.22
0.50
0.69
1.24
1.90
2.91
4.09
6.34
7.40
11.36
15.91q u
9 0 0 .3
0.16
0.36
0.54
0.93
1.23q u
2.50q u
3.67q u
5.86q u
6.88q u
10.10q u
15.24
1057
0.16
0.36
0.38
0.63
1.14
2.33q u
2.46
4.72q u
6.11q u
8.97q u
12.78q u
0.33
0.55
0.88q u
1.80q u
2.63q u
4.20q u
4.94q u
7.24q u
11.01q u
0.63q u
1.29q u
1.89q u
2.73q u
3.54q u
5.19q u
7.89q u
1255
0.11
0.26
1785
0.07
0.12
95
tech infoR2.p65
94
Black
7/19/2002, 11:01 AM
TECHNICAL INFORMATION
Maximum Mechanical Input HP Ratings at 870 RPM
TABLE 6
R e duc tion
Single
Nomina l
R a tio
Me rc ury
Ma rs
Ve nus
3 .5 3
15.10
30.20
68.23
4 .3 9
12.13
21.22
55.12
6 .1 2
6.53
15.25
41.93
39.95
76.83
98.34
169.03
1 1 .0 2
7.09
14.18
27.67
47.44
79.06
105.42
144.95
184.48
237.19
329.42
1 3 .8 5
6.20
12.39
23.39
40.40
68.03
90.36
122.25
159.45
201.98
276.39
1 7 .2 1
4.98
10.79
18.01
32.59
54.89
72.91
102.93
128.66
162.96
274.47
9 .3 0
Double
Ea rth
Pola ris
Ne ptune
Orion
S a t u rn
179.11
230.28
319.83
426.45
511.73
96.45
151.57
179.13
275.58
361.70
74.00
113.46
Jupite r
447.82
345.32
374.37
2 0 .4 1
4.00
8.00
17.53
28.97
53.36
76.23
99.09
121.96
160.07
213.43
342.48
4.17
8.34
13.53
23.37
40.59
55.35
83.03
104.56
129.16
215.26
264.66
3 1 .6 3
2.87
6.22
8.38
14.11
24.69
96.98
171.40
254.31
4 3 .7 8
1.72
3.44
18.04
31.33
37.98
71.21
80.71
3 6 .5 6
2.71
5.82
9.37
16.7
28.51
44.8
61.09
81.45
101.81
146.41
210.88d
4 3 .7 8
2.41
5.5
7.89
13.47
23.66
36.14
49.28
73.92
85.42
124.85
210.31
5 4 .4 5
2.26
4.80
6.36
11.13
19.09
29.16
39.77
55.67
71.58
106.04
174.94
52.90
6 4 .4 2
1.82
3.86
5.65
9.89
16.96
25.91
36.51
54.17
63.60
98.93
152.91
6 9 .6 3
1.50
3.63
4.70
8.34
14.54
22.46
31.01
49.19
59.88
85.54
145.99
4.56
7.98
14.06
21.85
30.41
41.81
57.01
81.72
123.35
6.03
8.57
8 0 .0 1
1.46
3.10
9 1 .4 1
1.30
2.77
9 9 .3 8
1.03
2.20
3.53
6.13
10.73
16.10
22.23
36.79
42.92
64.39
73.32
1 1 1 .5
1.05
2.23
3.27
5.72
10.08
15.67
21.80
29.97
40.87
59.94
88.42
1 2 1 .4
0.87
2.11
9.31
14.47
20.14
28.95
37.76
55.38
76.2
1 3 8 .5
0.74
1.58
2.53
4.29
7.69
12.09
16.49
26.38
30.77
46.16
52.56
2.67
4.79
1 5 9 .8
0.75
1.60
2.15q
3.85q
7.51q
11.68q
16.25q
24.37q
30.46q
44.68q
63.39q
1 9 3 .1
0.53
1.13
1.58
2.60
4.73
18.12
36.04
37.68
47.25
1 9 3 .1
Qua d
209.66
Tita n
2 4 .0 0
3 1 .6 3
Triple
A tla s
20.64
42.69
10.24
6.23
9.42
13.11
19.66
24.57
109.61
2 0 6 .2
0.62
1.31
1.73
3.11
5.53
8.37
11.65
17.47
21.84
32.03
2 3 8 .2
0.50
1.06
1.54
2.76
5.02
7.60
10.57
15.20
19.82
29.08
40.71
2 6 5 .4
0.27t
0.54t
1.40
2.51
4.46
6.75
9.40
14.09
17.62
25.84
38.12
0.41
0.99
2 9 5 .7
0.40
0.85
1.24
2.23
3.84
5.86
8.00
12.79
14.93
22.39
33.87
3 3 0 .1
0.36
0.80
1.08
1.88
3.60
5.45
7.58
10.90
14.21
20.84
30.75
3 6 9 .8
0.32
0.72
1.00
1.80
3.20
4.84
6.74
10.10
12.63
18.52
27.32
4 1 2 .1
0.29
0.64
0.89
1.60
2.75
4.20
5.92
9.17
10.70
16.43
26.5
4 5 9 .0
0.23
0.52
0.78
1.35
2.58
3.91
5.43
7.81
10.19
14.94
22.04
5 3 2 .5
0.23
0.52
0.72
1.29
1.97
3.01
4.25
6.58
7.67
11.78
19.59
6 1 7 .9
0.21
0.46
0.56
0.97
1.85
2.80
3.90
5.84
7.30
10.71
15.8
6 6 0 .6
0.16
0.37
1.25q u
2.66q u
3.81q u
5.40q u
7.14q u
10.47q u
12.81
7 4 1 .2
0.17
0.37
0.52
0.92
1.41
2.16
3.04
4.71
5.50
8.45
11.83q u
9 0 0 .3
0.12
0.27
0.40
0.69
0.91q u
1.86q u
2.73q u
4.35q u
5.12q u
7.51q u
11.33
1057
0.12
0.27
0.28
0.47
0.84
1.73q u
1.83
3.51q u
4.55q u
6.67q u
9.50q u
1255
0.08
0.19
0.25
0.41
0.66q u
1.34q u
1.96q u
3.12q u
3.67q u
5.38q u
8.19q u
1785
0.05
0.09
0.47q u
0.96q u
1.40q u
2.03q u
2.63q u
3.86q u
5.87q u
96
tech infoR2.p65
95
Black
7/19/2002, 11:01 AM
TECHNICAL INFORMATION
Couplings with Straight Bore Hubs
Sta nda rd
Ome ga
No.
R e c omm.
Ma x. B ore
(In.)
HP/1 0 0
R PM
1
Torque
(In. Lbs.)
1
Ma x.
R PM
V110
V125
V130
V170
V190
V215
V245
V290
E70
E80
E100
E120
E140
1.44
1.88
2.13
2.50
2.88
3.13
3.75
4.38
4.50
6.00
6.75
7.50
9.00
0.88
1.48
2.30
3.65
5.76
8.85
13.17
17.86
35.12
62.70
135
270
540
550
925
1450
2722
3650
5500
8297
11,250
22,125
39,500
85,050
170,100
340,200
5400
5400
5100
4800
4600
4300
4100
3900
3600
2000
1900
1800
1500
4.32
4.74
5.09
6.62
7.48
8.38
9.65
11.40
14.00
16.00
21.00
25.00
30.00
1.51
1.51
1.60
2.00
2.05
2.50
2.54
2.88
3.62
4.87
5.50
6.00
7.00
C
(IN)
0.34
0.36
0.26
0.36
0.26
0.44
0.28
0.32
0.75
0.75
1.75
2.25
3.00
(OUT)
2.16
2.18
2.16
2.36
2.36
2.51
2.86
3.72
3.75
5.00
3.75
4.88
5.00
D
23.7
2.75
3.13
3.75
4.62
6.88
6.75
8.47
9.25
11.25
14.13
17.63
20.88
F
(IN)
3.36
3.38
3.46
4.36
4.36
5.44
5.36
6.08
8.00
10.50
12.75
14.24
17.00
(OUT)
5.18
5.20
5.36
6.36
6.46
7.51
7.95
9.48
11.00
14.75
14.75
16.88
19.00
We ight
(Lbs.)
2
3.1
3.8
4.7
9.4
12.2
21.1
31.7
55.0
86
170
244
425
746
97
tech infoR2.p65
96
Black
7/19/2002, 11:01 AM
TECHNICAL INFORMATION
Table 7 - Viva Coupling Selection for Scoop Mount Reducers
Motor HP
Frame Size
Motor Shaft
Dia. (in.)
1
1.5
2
3
5
7.5
10
15
20
25
30
40
50
60
75
100
125
150
200
250
143T
145T
145T
182T
184T
213T
215T
254T
256T
284T
286T
324T
326T
364T
365T
404T
405T
444T
445T
447T
7/8
7/8
7/8
1 1/8
1 1/8
1 3/8
1 3/8
1 5/8
1 5/8
1 7/8
1 7/8
2 1/8
2 1/8
2 3/8
2 3/8
2 7/8
2 7/8
3 3/8
3 3/8
3 3/8
Motor HP
Frame Size
Motor Shaft
Dia. (in.)
1
1.5
2
3
5
7.5
10
15
20
25
30
40
50
60
75
100
125
150
200
250
143T
145T
145T
182T
184T
213T
215T
254T
256T
284T
286T
324T
326T
364T
365T
404T
405T
444T
445T
447T
7/8
7/8
7/8
1 1/8
1 1/8
1 3/8
1 3/8
1 5/8
1 5/8
1 7/8
1 7/8
2 1/8
2 1/8
2 3/8
2 3/8
2 7/8
2 7/8
3 3/8
3 3/8
3 3/8
Motor HP
Frame Size
Motor Shaft
Dia. (in.)
1
1.5
2
3
5
7.5
10
15
20
25
30
40
50
60
75
100
125
150
200
250
143T
145T
145T
182T
184T
213T
215T
254T
256T
284T
286T
324T
326T
364T
365T
404T
405T
444T
445T
447T
7/8
7/8
7/8
1 1/8
1 1/8
1 3/8
1 3/8
1 5/8
1 5/8
1 7/8
1 7/8
2 1/8
2 1/8
2 3/8
2 3/8
2 7/8
2 7/8
3 3/8
3 3/8
3 3/8
Mercury
1 3/8"
V110
V110
V110
V110
V110
V110
V110
V125
V125
V125
V130
Mercury
1 3/8"
V110
V110
V110
V110
V110
V110
V110
V125
V130
Mercury
1 3/8"
V110
V110
V110
V110
V110
V110
V125
V130
Note: Taper-Lock hub (reducer side only) required on Polaris (s,d,t) when a fan is used.
tech infoR2.p65
97
Black
V215
V215
V215
V215
V215
V215
V215
V215
V215
V245
V245
V290
V215
V215
V215
V215
V215
V215
V215
V215
V215
V245
V245
V290
E70
V215
V215
V215
V215
V215
V215
V215
V215
V215
V245
V290
V290
E70
E70
98
7/19/2002, 11:02 AM
TECHNICAL INFORMATION
Load Location Factors High Speed and Low Speed Shafts
TABLE 8
TABLE 9
Reducer Series
Distance
in
Inches Mercury
Mars
Venus (q)
Atlas (q)
Earth (qu)
Polaris (qu)
Venus
Atlas
Earth (q)
Polaris (q)
Neptune (qu)
Orion (qu)
Saturn (qu)
Titan (qu)
Earth
Polaris
Neptune(q)
Orion (q)
Neptune
Orion
Saturn (q)
Titan (q)
Saturn
Titan
Jupiter
0.84
0.77
0.71
0.72
0.67
0.70
0.72
0.72
1 1/4
1 1/2
0.69
0.63
0.61
0.88
0.81
0.75
0.74
0.70
0.73
0.74
0.92
0.85
0.80
0.78
0.72
0.75
0.76
0.74
0.71
0.65
0.63
0.75
0.72
0.67
0.65
1 3/4
0.96
0.89
0.84
0.81
0.75
0.78
0.78
0.77
0.74
0.69
0.67
3/4
0.85
0.80
0.80
0.73
0.70
0.73
1.00
0.92
0.88
0.84
0.78
0.80
0.80
0.79
0.76
0.70
0.69
0.91
0.86
0.85
0.78
0.74
0.76
2 1/4
1.04
0.96
0.92
0.87
0.81
0.83
0.82
0.81
0.78
0.72
0.70
2 1/2
1.08
1.00
0.96
0.90
0.83
0.85
0.84
0.82
0.79
0.73
0.72
2 3/4
1.12
1.04
1.00
0.93
0.86
0.88
0.86
0.84
0.81
0.75
0.73
1.16
1.08
1.04
0.97
0.90
0.90
0.88
0.86
0.83
0.77
0.75
1 1/4
0.97
0.91
0.89
0.82
0.79
0.79
1 1/2
1.03
0.97
0.93
0.87
0.83
0.82
1 3/4
1.09
1.03
0.98
0.92
0.87
0.85
3 1/4
1.20
1.11
1.08
1.00
0.95
0.93
0.90
0.88
0.85
0.78
0.77
3 1/2
1.25
1.15
1.12
1.03
1.00
0.95
0.92
0.89
0.86
0.80
0.78
3 3/4
1.29
1.19
1.16
1.06
1.05
0.97
0.94
0.91
0.88
0.82
0.80
1.33
1.23
1.10
1.09
1.10
1.00
0.96
0.93
0.90
0.83
0.82
1.15
1.09
1.02
0.97
0.91
0.88
2 1/4
1.21
1.14
1.07
1.03
0.96
0.91
2 1/2
1.27
1.20
1.11
1.08
1.00
0.94
4 1/4
1.26
1.25
1.12
1.14
1.02
0.98
0.95
0.91
0.85
0.89
2 3/4
1.33
1.26
1.15
1.13
1.04
0.97
4 1/2
1.30
1.29
1.16
1.19
1.05
1.00
0.96
0.93
0.87
0.85
1.39
1.31
1.20
1.18
1.09
1.00
4 3/4
1.34
1.33
1.19
1.24
1.07
1.02
0.98
0.95
0.88
0.87
1.38
1.37
1.22
1.29
1.10
1.06
1.00
0.97
0.90
0.88
1.45
3 1/4
1.37
1.25
1.23
1.13
1.03
3 1/2
1.43
1.31
1.28
1.17
1.06
1.38
1.33
1.21
5 1/2
3 3/4
1.28
1.38
1.15
1.12
1.04
1.00
0.93
0.91
1.35
1.48
1.20
1.19
1.07
1.03
0.97
0.95
1.09
6 1/2
1.41
1.57
1.25
1.25
1.11
1.07
1.00
0.97
1.67
1.30
1.32
1.14
1.10
1.03
1.00
7 1/2
1.35
1.39
1.18
1.14
1.07
1.03
1.40
1.45
1.21
1.17
1.10
1.07
1.44
1.38
1.26
1.12
4 1/4
1.50
1.43
1.31
1.15
4 1/2
1.49
1.37
1.18
8 1/2
1.52
1.25
1.21
1.13
1.10
4 3/4
1.42
1.21
1.58
1.28
1.24
1.17
1.13
1.47
1.24
9 1/2
1.32
1.28
1.20
1.17
10
1.35
1.31
1.23
1.20
5 1/2
1.58
1.30
1.36
6 1/2
1.42
10 1/2
1.34
1.27
1.23
11
1.38
1.30
1.27
12
1.30
* Factor based on the distance from load centerline to reducer seal cage.
* Factor based on the distance from load centerline to reducer seal cage.
99
tech infoR2.p65
98
Black
7/19/2002, 11:02 AM
TECHNICAL INFORMATION
Overhung Load Capacity High Speed and Low Speed Shafts
TABLE 10
Overhung Load Capacity - POUNDS*
High Speed Shafts
H.S. Shaft
RPM
Mercury
1750
1430
1170
870
720
580
720
765
813
888
940
1,000
Reducer Series
Venus
Atlas
M ar s
Earth (q)
Earth
Venus (q)
Polaris (q)
Polaris
Atlas (q)
Neptune (qu) Neptune (q)
Earth (qu)
Orion (qu)
Orion (q)
Polaris (qu)
Saturn (qu)
Titan (qu)
679
941
1,500
721
999
1,600
766
1,060
1,700
837
1,160
1,860
886
1,230
1,960
946
1,310
2,100
Neptune
Orion
Saturn (q)
Titan (q)
Saturn
Titan
Jupiter
1,900
2,040
2,160
2,360
2,500
2,670
2,500
2,660
2,830
3,100
3,270
3,490
* Capacities are for pure radial loads. If overhung and thrust loads are applied together or if radial loads
exceed listed capacities, consult factory.
If desired speed is not shown, use next higher speed.
q = quadruple reduction (values do not pertain to other reductions within this particular reducer series.)
qu = quintuple reduction (values do not pertain to other reductions within this particular reducer series.)
TABLE 11
Overhung Load Capacity - POUNDS*
Low Speed Shafts
Approximate
L.S. Shaft
RPM
496
399
286
159
126
102
86
73
55
48
40
32
27
25
22
19.1
17.6
15.7
14.4
12.6
11.0
9.1
6.4
Reducer Series
Mercury
M ar s
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
2,230
2,380
2,630
3,080
3,320
3,540
3,780
3,910
4,180
4,420
4,610
4,930
5,260
5,360
5,630
5,820
6,010
6,210
6,390
6,630
6,870
7,020
7,020
2,060
2,200
2,430
2,850
3,070
3,270
3,500
3,620
3,860
4,080
4,270
4,560
4,870
4,960
5,200
5,380
5,550
5,590
5,590
5,590
5,590
5,590
5,590
4,390
4,680
5,180
6,300
6,720
7,160
7,420
7,920
8,750
9,030
9,630
10,300
10,600
11,000
11,400
11,900
12,100
12,500
12,700
12,700
12,700
12,700
12,700
3,970
4,200
4,700
5,600
6,000
6,390
6,720
7,060
7,680
8,000
8,460
9,040
9,500
9,740
10,100
10,600
11,800
11,800
11,800
11,800
11,800
11,800
11,800
6,150
6,560
7,250
8,820
9,410
10,000
10,400
11,100
12,200
12,600
13,500
14,400
14,900
15,300
15,900
16,600
16,900
17,600
18,200
18,300
18,300
18,300
18,300
6,550
7,000
7,750
9,250
9,950
10,600
11,100
11,700
12,700
13,200
14,000
15,000
15,800
16,100
16,800
17,500
17,900
18,500
19,000
19,800
20,600
21,800
23,000
11,500
12,250
13,600
16,200
17,400
18,500
19,500
20,500
22,300
23,250
24,500
26,250
27,500
27,500
27,500
27,500
27,500
27,500
27,500
27,500
27,500
27,500
27,500
13,450
14,350
15,850
18,900
20,300
21,600
22,750
23,900
26,000
27,100
28,600
29,700
29,700
29,700
29,700
29,700
29,700
29,700
29,700
29,700
29,700
29,700
29,700
14,300
15,300
16,950
20,200
21,650
23,000
24,300
25,500
27,750
28,900
30,500
32,400
32,400
32,400
32,400
32,400
32,400
32,400
32,400
32,400
32,400
32,400
32,400
15,400
16,400
18,200
21,700
23,200
24,700
26,000
27,300
29,800
31,000
32,800
35,000
36,900
37,700
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
38,000
16,000
17,000
18,800
22,400
24,000
25,600
27,000
28,300
30,900
32,200
34,000
36,300
38,200
39,100
40,600
42,400
43,500
45,000
46,200
48,000
50,000
53,000
58,900
* Capacities are for pure radial loads. If overhung and thrust loads are applied together or if radial loads exceed listed capacities, consult factory.
Interpolate for intermediate values for a min. of 5,000 hr L10 life.
For slower speeds, use the capacity at 6.4 RPM.
100
tech infoR2.p65
99
Black
7/19/2002, 11:03 AM
TECHNICAL INFORMATION
Horizontal Service Thermal HP Limits - 1750 RPM Input Speed
TABLE 12
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating.
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Re d uce r Se rie s
13.85
10
10
10
17.21
10
20.41
10
24.00
11
31.63d
11
31.63t
25
Without Fan
With Fan
C-Face
Without Fan
With Fan
Without Fan
With Fan
Without Fan
With Fan
30
20
125
25
100
25
15
125
20
15
150
15
20
210
20
150
25
150
14**
43
103 43**
44
104 44**
15
135
30
20
250
25
375
20
75
25
15
100 40**
15
125
20
25
200
10
31
31**
20
75
30
15
100
20
15
125
30
25
185
25
185
25
150
25
200
10
52
52**
46
81
46**
20
100
30
20
150
30
25
230
25
230
25
230
25
310
M
P
D
R
E
0 PE L
5
17 T S TA
N
U
P
O
Z
N
I
I
R
O
H
With Fan
10
100
Jup ite r
Without Fan
10
Titan
With Fan
10
100 38**
Saturn
Without Fan
11.02
38
Orio n
C-Face
9.30
11*
Ne p tune
With Fan
14
30
Po laris
Without Fan
15**
75
Earth
C-Face
15
20
With Fan
6.12
40
Without Fan
11
C-Face
13**
With Fan
13
Atlas
Without Fan
4.39
32
Ve nus
C-Face
12**
Without Fan
12
C-Face
3.53
With Fan
No minal
Ratio
With Fan
Mars
Without Fan
Me rcury
25
155
10
50
50**
30
100 40**
30
140
30
25
260
25
275
25
285
25
380
10
70
70**
45
105 45**
40
160
30
25
240
25
250
35
350
55
470
40
445
11**
50
110
40
40**
30
30
275
35
55
515
60
490
11**
55
55**
25
500
30
30
30
55
55**
30
65
65**
30
50**
40
35
30
25
100
25
150
25
150
40
200
85
30
25
115
25
135
25
150
40
200
155
100
30
30
120
35
145
35
165
55
205
20
260
40
40**
30
40
145
50
180
70
225
40
260
40
40**
30
35
140
45
175
60
215
85
320
69.63
35
35**
30
45
55
70
230
95
335
80.01
50
50**
30
45
65
70
100
335
91.41
30
40
40
99.38
30
50
70
70
105
111.5
30
45
80
100
150
75
155
105
125
36.56
7.5
43.78
7.5
54.45
7.5
64.42
10
33
10
10
31
31
121.4
138.5
30
50
80
140
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
101
tech infoR2.p65
100
Black
7/19/2002, 11:03 AM
TECHNICAL INFORMATION
Horizontal Service Thermal HP Limits - 1430 RPM Input Speed
TABLE 12
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating.
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Reducer Series
20.41
24.00
31.63d
With Fan
C-Face
Without Fan
With Fan
C-Face
Without Fan
With Fan
Without Fan
With Fan
Without Fan
With Fan
Without Fan
10
100
10
10
155
10
20
165
20
65
25
50
20
15
245
15
30
270
25
270
25
270
40
300
65
470
122 57**
43
108 43**
20
135
16
16**
61
61**
62
127 62**
70
175 70**
30
30
50
100 50**
30
150
30
25
200
40**
40
100 40**
40
145 40**
25
235
25
235
25
200
25
275
275
40
300
25
320
35
410
370
40
465
C-Face
57
With Fan
14**
M
P
D
R
E
0 PE L
3
14 T S TA
N
U
P
O
Z
N
I
I
R
O
H
10
10
47
47**
40
92
10
10
59
59**
50
110
50**
40
170 40**
40
11
11**
63
63**
60
115
60**
40
40**
55
55
30
11
11**
75
75**
50
50**
50
50
40
13
13**
70
70**
60
60**
60
60
40
75
31.63t
30
36.56
7.5
43.78
54.45
64.42
Titan
7.5
69.63
80.01
30
30
30
30
30
30
50
100 50**
30
40
40**
45
30
125
Jupiter
With Fan
17.21
Saturn
Without Fan
13.85
Orion
With Fan
11.02
Neptune
Without Fan
9.30
101 40**
Polaris
Without Fan
6.12
40
Earth
14
42
C-Face
14**
With Fan
14
Atlas
Without Fan
4.39
Venus
C-Face
14**
With Fan
14
C-Face
3.53
With Fan
Nominal
Ratio
Without Fan
Mars
Without Fan
Mercury
25
350
85
75
590
85
100
40
50
30
60
40
155
40
180
65
220
210
40
50
160
50
190
75
235
60
305
45**
40
55
65
90
65
305
50
50**
40
50
60
85
85
355
45
45**
40
60
70
95
85
40
60
75
105
125
91.41
160
99.38
40
60
80
110
130
111.5
40
60
85
115
170
121.4
175
138.5
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
102
tech infoR2.p65
101
Black
7/19/2002, 11:03 AM
TECHNICAL INFORMATION
Horizontal Service Thermal HP Limits - 1170 RPM Input Speed
TABLE 12
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating.
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Reducer Series
31.63d
31.63t
36.56
235
30
240
30
250
61
130 61**
60
205
60
40
325
75**
40
325
40
330
50
380
18**
75
75**
76
76**
115
115**
60
345
105
545
40
40**
75
75**
30
40**
30
11**
52
52**
75
130 75**
50
180 50**
35
50
50
290
12**
70
70**
75
75**
50
50**
65
65
70
70**
55
55**
85
85
85**
70
70**
75
75**
50
380
55
70
490
85
70
70
75
75
70
140
115
90
90
70
140
150
M
P
D
R
E
0 PE L
7
11 T S TA
N
U
P
O
Z
N
I
I
R
O
H
13**
340
90
50
40
50
100
30
510
35
35**
40
60
60
100
50
50**
50
65
70
100
95
50
50**
50
65
80
105
100
45
65
75
100
105
69.63
50
70
85
110
105
80.01
50
70
90
120
150
43.78
54.45
64.42
91.41
245
With Fan
30
Without Fan
40**
Jupiter
With Fan
250
C-Face
30
With Fan
Without Fan
30
C-Face
140
C-Face
30
Titan
Without Fan
24.00
With Fan
20.41
Without Fan
13
With Fan
17.21
Without Fan
12
With Fan
13.85
Without Fan
11
C-Face
11.02
75**
Saturn
With Fan
9.30
72
Orion
Without Fan
18
16**
Neptune
C-Face
6.12
124 55**
Polaris
With Fan
16
55
Earth
Without Fan
4.39
Atlas
With Fan
49
Venus
Without Fan
22**
With Fan
Without Fan
22
Mars
C-Face
3.53
With Fan
Nominal
Ratio
Without Fan
Mercury
305
175
99.38
111.5
121.4
138.5
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
103
tech infoR2.p65
102
Black
7/19/2002, 11:03 AM
340
TECHNICAL INFORMATION
Horizontal Service Thermal HP Limits - 870 RPM Input Speed
TABLE 12
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Reducer Series
330
30
370
20
6.12
9.30
11.02
20**
13
13.85
17.21
20.41
24.00
31.63d
31.63t
36.56
82
82**
93
93**
130
130** 100
54.45
64.42
90
385
90
110
50
50**
75
400
40
510
140
85
85**
75
75**
80
80
55
70
90
90**
75
75**
105
105
105
140
85
85**
120
140
140
140
95
95**
110
145
210
210
210
210
220
125
265
45
43.78
100*
45**
With Fan
30
Jupiter
Without Fan
With Fan
315
With Fan
Without Fan
30
Titan
Without Fan
With Fan
75**
M D
P
R
E
0 PE L
7
8 T S TA
N
U
P
O
Z
N
I
I
R
O
H
4.39
Saturn
Without Fan
Orion
With Fan
75
With Fan
With Fan
105**
Neptune
Without Fan
105
Polaris
C-Face
77**
Without Fan
C-Face
With Fan
Without Fan
C-Face
With Fan
Earth
Without Fan
77
Atlas
C-Face
3.53
Without Fan
Venus
C-Face
With Fan
Without Fan
Mars
C-Face
With Fan
Nominal
Ratio
Without Fan
Mercury
100
125
50
75
80
110
55
80
90
115
150
100
125
140
120
170
69.63
175
80.01
91.41
99.38
111.5
121.4
138.5
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
104
* Contact factory for heat exchanger selection.
tech infoR2.p65
103
Black
7/19/2002, 11:04 AM
d = double reduction
t = triple reduction
TECHNICAL INFORMATION
Vertical Service Thermal HP Limits - 1750 RPM Input Speed
TABLE 13
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating.
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Reducer Series
85
60
6.12
10
10
12
12**
94
12
9.30
11.02
10
10
10
13.85
10
10
10
17.21
10
20.41
10
24.00
10
31.63d
10
31.63t
36.56
7.5
43.78
7.5
54.45
7.5
50
50
70
101
12
15
100
15
140
175
175
40
50
50
75
50
60
60
100
100
75
100
103
30
20
75
20
20
85
20
175
175
100
150
C-Face
With Fan
With Fan
10
Without Fan
40
With Fan
10
Without Fan
10
With Fan
10
Without Fan
4.39
With Fan
Without Fan
34
M
P
D
R
E
0 PE
5
17 T S AL
U TIC
P
IN ER
V
25
10
10
40
40**
30
10
51
51**
37
37**
15
100
15
30
110
30
210
210
135
210
76
76**
20
80
20
30
150
30
210
210
210
285
10
20
90
20
40
40**
250
350
10
25
25
35
350
15
15
30
10
70
Titan
C-Face
Saturn
With Fan
10
Orion
Without Fan
34
Neptune
C-Face
C-Face
10
Polaris
With Fan
With Fan
10
Earth
Without Fan
Without Fan
10
Without Fan
C-Face
3.53
With Fan
Nominal
Ratio
With Fan
Atlas
Without Fan
Venus
C-Face
Mars
Without Fan
Mercury
100
30
115
130
100
75
150
115
105
170
20
140
140
205
10
27
27
30
30
30
10
31
31**
30
30
30
30
20
35
35**
40
40**
30
25
175
20
235
64.42
35
35**
40
40**
30
20
20
165
20
220
69.63
35
35**
25
25
30
30
30
35
55
55**
30
35
40
55
10
80.01
80
30
91.41
30
40
99.38
30
40
40
65
111.5
30
35
55
75
121.4
75
138.5
15
40
60
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
Contact factory for Jupiter and Neptune/Saturn/Titan low speed shaft up applications.
105
tech infoR2.p65
104
Black
7/19/2002, 11:04 AM
85
TECHNICAL INFORMATION
Vertical Service Thermal HP Limits - 1430 RPM Input Speed
TABLE 13
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating.
Based on 80F ambient temperature. See page 109 for adjustment dfactors at different temperatures.
Reducer Series
41
41
44
138
With Fan
15**
Without Fan
15
With Fan
100
Without Fan
30
With Fan
34
Without Fan
125
With Fan
34
Without Fan
11**
50
50
30
75
105
140
50
50
44**
20
125
20
260
350
30
15
60
15
15
60
15
150
30
20
75
20
20
105
20
200
200
100
150
140
30
265
250
195
285
285
350
300
C-Face
M
P
D
R
E
0 PE
3
14 T S AL
U TIC
P
IN ER
V
30
11.02
13.85
17.21
20.41
24.00
31.63d
31.63t
36.56
10
10
10
10
52
52**
30
85
30
30
10
10
59
59**
40
95
40**
40
40**
10
10
50
50**
50
50**
12
12**
60
60**
7.5
30
30
34**
30
30
35**
50
50**
30
45
45**
35
35**
40
40
40**
64.42
50
69.63
40
*
*
170
225
45
30
195
250
40
50
50
50**
40
40
40
45
40**
40
55
55
70
40
55
60
85
99.38
35
60
65
95
111.5
30
55
75
105
54.45
34
87
35
43.78
7.5
30
Titan
C-Face
11
Saturn
With Fan
Orion
Without Fan
83
Neptune
C-Face
Polaris
With Fan
12**
With Fan
C-Face
10
Without Fan
With Fan
46
Earth
Without Fan
9.30
Without Fan
6.12
12
Atlas
C-Face
10
10
Venus
With Fan
4.39
Without Fan
10
Mars
C-Face
3.53
With Fan
Nominal
Ratio
Without Fan
Mercury
80.01
140
35
170
91.41
121.4
138.5
35
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
Contact factory for Jupiter and Neptune/Saturn/Titan low speed shaft up applications.
106
tech infoR2.p65
105
Black
7/19/2002, 11:04 AM
TECHNICAL INFORMATION
Vertical Service Thermal HP Limits - 1170 RPM Input Speed
TABLE 13
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Reducer Series
17.21
12
20.41
24.00
31.63d
31.63t
36.56
With Fan
11
Without Fan
13.85
With Fan
10
Without Fan
11.02
With Fan
9.30
Without Fan
19
With Fan
6.12
Without Fan
15
C-Face
4.39
20
75
20
20
105
20
125
100
100
40**
30
110
30
30
140
30
210
210
210
70
70**
50
50**
345
545
40
40**
40
40**
40
75
40**
50
50**
50
110
50**
50
140
50**
150
230
71
71**
75
125
75**
50
50**
20
20
285
450
75
75**
50
50**
45
65
300
15
15
60
60**
50
30
20
20
50
50**
75
65
30
30
55
40
130
40
40
40
M
P
D
R
E
0 PE
7
11 T S AL
U TIC
P
IN ER
V
15**
57
57**
40
19**
68
68**
10
11**
51
51**
Titan
With Fan
30
Saturn
Without Fan
122
Orion
C-Face
30
Neptune
With Fan
19**
Polaris
Without Fan
C-Face
55
C-Face
With Fan
19
Earth
With Fan
Without Fan
15**
Without Fan
C-Face
Atlas
With Fan
Venus
Without Fan
15
Mars
C-Face
3.53
With Fan
Nominal
Ratio
Without Fan
Mercury
137
12**
50
25
25
40
55
50
50
45
45**
50
65
50
70
50
50**
50
70
75
90
64.42
35
60
60
80
69.63
45
75
70
85
80.01
45
75
85
85
43.78
54.45
50**
270
91.41
99.38
120
111.5
121.4
138.5
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
Contact factory for Jupiter and Neptune/Saturn/Titan low speed shaft up applications.
107
tech infoR2.p65
106
Black
7/19/2002, 11:04 AM
270
TECHNICAL INFORMATION
Vertical Service Thermal HP Limits - 870 RPM Input Speed
TABLE 13
Thermal HP Limits
Maximum motor HP (without service factor) that reducer will transmit continuously without overheating
Based on 80F ambient temperature. See page 109 for adjustment factors at different temperatures.
Reducer Series
With Fan
With Fan
Without Fan
Without Fan
50**
210
210
200
15
75
75**
50
50
30
30
460
30
30
75
75**
80
80
50
70
35
35**
65
65**
105
105
90
105
35
35**
85
85**
90
120
180
140
110
145
M D
P
R
E
0 PE
7
8 T S AL
U TIC
P
IN ER
V
4.39
20
6.12
9.30
11.02
13
13.85
17.21
20.41
24.00
31.63t
36.56
43.78
20**
78
78**
75
75**
100
100**
30
30
67
67**
75
75**
30
375
460
60
50
50**
40
45
54.45
Titan
15
With Fan
With Fan
50
Without Fan
50**
Saturn
With Fan
Without Fan
200
Orion
Without Fan
C-Face
50
Neptune
C-Face
With Fan
C-Face
69**
Polaris
Without Fan
Earth
With Fan
Without Fan
69
Atlas
C-Face
26**
With Fan
Without Fan
With Fan
26
Venus
C-Face
3.53
Without Fan
Mars
C-Face
With Fan
Nominal
Ratio
Without Fan
Mercury
45**
210
220
125
50
80
65
95
55
90
85
110
100
125
64.42
69.63
115
80.01
91.41
99.38
111.50
121.40
138.50
If the nominal ratio is not listed or no value is given above, your application will not be thermally limited. Refer to page 5 and 109 for other conditions.
* Contact factory for heat exchanger selection.
** Check for available motor frame sizes.
d = double reduction
t = triple reduction
Contact factory for Jupiter and Neptune/Saturn/Titan low speed shaft up applications.
108
tech infoR2.p65
107
Black
7/19/2002, 11:05 AM
TECHNICAL INFORMATION
Tables
TABLE 14
Ambient Temperature Adjustment Factor (AC)
Ambient Temperature
(F)
below 54
55 to 69
70 to 84
85 to 99
100 to 114
above 115
TABLE 15
Extended Usable Input Shaft Lengths
Reducer
Series
Mercury
Shaft Length
6.00
M ar s
Venus Quad
Atlas Quad
7.00
Venus
Earth Quad
Polaris Quad
8.50
Atlas
Earth Quad
Polaris Quad
8.50
Earth, Polaris
Neptune Quad
Orion Quad
9.00
Neptune, Orion
Saturn Quad
Titan Quad
11.56
Saturn
Titan
Jupiter
13.00
Mercury
M ar s
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
7.15
12.44
11.00
13.00
12.00
14.00
16.00
17.00
19.00
TABLE 16
Nominal and Actual Reduction Ratios
R e duc tion
Single
Double
Nomina l
R a tio
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
1 7 .2 1
2 0 .4 1
2 4 .0 0
3 1 .6 3
Me rc ury
3.75
4.67
6.50
Ma rs
3.75
4.67
6.50
Ve nus
3.32
4.11
5.74
10.24
14.06
17.50
21.78
24.38
30.33
10.24
14.06
17.50
21.78
24.38
30.33
11.02
13.66
16.93
19.05
23.61
32.94
38.40
d 42.25
45.00
52.73
65.63
69.69
81.67
91.41
101.63
113.75
q 122.88
141.56
36.57
45.33
5 4 .4 5
6 4 .4 2
6 9 .6 3
8 0 .0 1
9 1 .4 1
9 9 .3 8
1 1 1 .5
1 2 1 .4
1 3 8 .5 0
38.40
d 42.25
45.00
52.73
65.63
69.69
81.67
91.41
101.63
113.75
q 122.88
141.56
1 5 9 .8
1 9 3 .1
158.44
197.17
158.44
197.17
3 6 .5 6
4 3 .7 8
Triple
2 0 6 .2
2 3 8 .2
2 6 5 .4
56.18
63.23
69.64
78.37
A tla s
4.11
5.74
9.45
11.02
13.66
16.93
19.05
23.61
32.94
t31.37
36.57
45.33
97.15
109.32
56.18
63.23
69.64
78.37
93.79
97.15
109.32
135.51
q 137.12
q 170.64
189.03
135.51
q 137.12
q 170.64
189.03
197.75
197.75
211.52
211.52
246.09
246.09
237.68
237.68
t274.63
t274.63
262.19
262.19
261.33
261.33
2 9 5 .7
306.25
306.25
294.62
294.62
3 3 0 .1
342.77
342.77
325.01
325.01
3 6 9 .8
381.11
381.11
365.20
365.20
4 1 2 .1
426.56
426.56
410.97
410.97
Qua druple
4 5 9 .0
474.27
474.27
452.69
452.69
5 3 2 .5
530.83
530.83
509.43
509.43
6 1 7 .9
594.14
594.14
631.46
631.46
6 6 0 .6
660.59
660.59
7 4 1 .2
739.38
739.38
710.61
710.61
9 0 0 .3
920.11
920.11
880.85
880.85
1057
1029.84
1029.84
1080.19
1080.19
1255
1281.58
1281.58
1228.72
1228.72
1785
1785.06
1785.06
d = double reduction, t = triple reduction, q = quadruple reduction, qu = quintuple reduction
E a rt h
3.32
4.11
5.74
9.45
11.02
13.66
16.93
19.05
23.61
32.94
t31.37
36.57
45.33
56.18
63.23
69.64
78.37
93.79
97.15
109.32
q 121.37
135.51
q 150.44
189.03
q 186.48
209.86
231.16
260.13
286.54
322.45
362.87
399.70
449.79
557.55
627.43
q u676.79
777.74
q u925.44
1084.89
q u1289.00
q u1798.07
R e duc e r Type
Pola ris
Ne ptune
3.32
3.32
4.11
4.11
5.74
9.45
9.45
11.02
11.02
13.66
13.66
16.93
16.93
19.05
19.05
23.61
23.61
32.94
t31.37
t31.37
36.57
36.57
45.33
45.33
56.18
63.23
69.64
78.37
97.15
109.32
q 121.37
135.51
q 150.44
56.18
63.23
69.64
78.37
93.79
97.15
109.32
q 121.37
135.51
Orion
3.32
4.11
Sa turn
3.32
4.11
5.74
Tita n
11.02
13.66
16.93
19.05
23.61
11.02
13.66
16.93
19.05
23.61
32.94
11.02
13.66
16.93
19.05
23.61
30.50
19.08
24.69
28.55
36.57
45.33
36.57
45.33
d 34.43
42.49
56.18
63.23
69.64
78.37
90.71
97.15
109.32
q 121.37
135.51
56.18
63.23
69.64
78.37
97.15
109.32
q 121.37
135.51
51.08
63.31
65.29
78.48
88.32
101.56
109.48
127.05
141.67
q 150.44
q 186.48
152.71
197.63
209.86
231.16
260.13
210.15
243.87
260.49
286.54
322.45
362.87
399.70
449.79
557.55
627.43
q u658.21
777.74
q u918.16
q u1033.24
q u1280.77
q u1786.58
293.14
322.89
363.37
374.71
450.41
506.87
628.30
655.95
q u728.21
876.43
q u1071.74
q u1243.73
q u1734.92
t31.37
36.57
45.33
56.18
63.23
69.64
78.37
97.15
109.32
121.37
135.51
q 186.48
209.86
231.16
260.13
q 150.44
189.03
q 186.48
209.86
231.16
260.13
150.44
186.48
209.86
231.16
260.13
q 150.44
189.03
q 186.48
209.86
231.16
260.13
286.54
322.45
362.87
399.70
449.79
557.55
627.43
q u676.79
777.74
q u925.44
q u1039.89
q u1289.00
q u1798.07
286.54
322.45
362.87
399.70
449.79
557.55
627.43
q u658.21
777.74
q u918.16
1084.89
q u1280.77
q u1786.58
286.54
322.45
362.87
399.70
449.79
557.55
627.43
q u696.55
777.74
q u863.42
q u1070.26
q u1204.40
q u1850.58
286.54
322.45
362.87
399.70
449.79
557.55
627.43
q u658.21
777.74
q u918.16
q u1033.24
q u1280.77
q u1786.58
109
tech infoR2.p65
108
Black
7/19/2002, 11:05 AM
Jupite r
12.80
TECHNICAL INFORMATION
Moment of Inertia - WR 2 at Reducer Input
TABLE 17
R e duc tion
Single
Double
Triple
Qua d / Quint
Nomina l
R a tio
R e duc e r Type
Me rc ury
(lb-in)
4.62
3.67
2.87
Ma rs
(lb-in)
6.95
5.36
3.97
Ve nus
(lb-in)
30.29
21.73
14.59
Pola ris
(lb-in)
165.91
113.42
16.31
12.69
27.59
18.07
19.81
18.56
14.33
Ea rth
(lb-in)
132.47
89.11
51.72
46.14
40.59
29.07
5.45
4.25
6.10
4.77
1 7 .2 1
2 0 .4 1
2 4 .0 0
3.42
3.37
2.73
3.89
3.82
3.16
12.19
9.51
9.26
13.70
10.55
10.22
26.44
19.22
17.87
3 1 .6 3
4 3 .7 8
3 1 .6 3
3 6 .5 6
4 3 .7 8
5 4 .4 5
2.70
2.68
3.12
3.08
9.04
9.93
16.76
4.27
4.19
4.18
4.67
4.59
4.58
14.77
12.43
12.21
15.09
14.97
12.56
12.31
19.23
18.72
15.68
15.00
22.75
21.17
16.63
15.79
73.09
66.05
53.15
49.58
6 4 .4 2
6 9 .6 3
8 0 .0 1
3.36
3.33
3.33
3.75
3.72
3.71
8.88
12.18
8.77
8.95
12.27
8.82
11.50
14.85
11.15
12.55
15.60
12.12
9 1 .4 1
9 9 .3 8
1 1 1 .5
2.68
3.32
2.7
3.07
3.71
3.0
8.76
8.68
8.72
8.80
8.71
10.91
11.07
10.85
12.02
11.73
1 3 8 .5
1 9 3 .1
1 2 1 .4
1 3 8 .5 0
1 5 9 .8 *
2.66
2.58
4.27
3.04
2.97
4.65
2.64
3.03
4.66
3.67
8.70
8.69
4.69
4.68
3.68
10.81
10.78
14.84
12.47
12.24
2 0 6 .2
2 3 8 .2
2 6 5 .4
4.18
3.36
3.33
4.57
3.75
3.71
3.53
2.40
3.52
3.53
2.40
3.52
2 9 5 .7
3 3 0 .1
3 6 9 .8
3.32
2.68
3.32
3.71
3.06
3.71
2.76
3.52
2.76
4 1 2 .1
4 5 9 .0
5 3 2 .5
2.66
3.32
2.66
3.04
3.71
3.04
6 1 7 .9
6 6 0 .6
7 4 1 .2
2.64
2.66
2.64
3.03
3.04
3.03
9 0 0 .3
1057
1255
2.64
2.64
2.64
3.03
3.03
3.03
1785
2.64
3.03
3 .5 3
4 .3 9
6 .1 2
9 .3 0
1 1 .0 2
1 3 .8 5
8.67
8.66
A tla s
(lb-in)
Orion
(lb-in)
798.12
543.23
Sa turn
(lb-in)
1246.99
884.49
526.26
Tita n
(lb-in)
Jupite r
(lb-in)
67.77
50.31
36.08
Ne ptune
(lb-in)
624.57
413.40
237.13
205.27
201.01
140.79
216.50
151.59
764.45
528.88
822.27
566.60
1334.77
32.97
23.31
21.72
128.28
89.45
83.03
136.50
95.25
87.51
503.47
330.11
317.08
529.87
349.44
330.61
914.02
880.62
306.20
251.50
706.16
75.02
67.45
54.07
50.22
276.01
213.49
199.53
281.26
216.92
201.76
524.27d
772.43
768.56
42.01
48.84
40.18
42.48
49.33
40.51
160.09
198.02
152.93
161.84
199.59
154.07
531.56
506.87
505.22
42.92
39.80
38.62
40.05
38.80
158.42
152.16
146.89
152.96
147.48
331.48
503.24
317.98
77.68
11.68
38.56
15.06
12.61
12.35
38.43
38.27
19.10
15.93
15.16
146.91
19.23
16.01
15.22
146.49
146.16
66.62
53.53
49.83
8.90
12.20
8.79
8.98
12.30
8.84
11.62
14.95
11.23
11.67
14.99
11.26
42.20
49.00
40.30
42.36
49.14
40.41
213.72
160.32
199.68
2.77
3.52
2.76
12.19
8.77
8.68
12.28
8.81
8.72
14.91
11.12
10.89
14.94
11.14
10.91
48.91
39.88
38.68
49.01
39.95
.
198.12
153.00
2.70
2.76
2.70
2.70
2.76
2.70
8.76
8.67
8.67
8.81
8.70
8.70
11.10
10.84
10.83
11.12
10.85
10.83
39.83
38.47
38.44
39.88
38.50
38.47
152.26
152.21
146.93
2.70
2.70
2.70
8.66
2.11
8.66
8.69
2.12
8.69
10.79
16.03
10.78
10.80
8.92
10.79
38.28
13.42
38.27
38.30
13.44
38.28
146.52
146.88
66.62
2.70
2.70
2.92
2.70
2.70
2.92
2.70
3.52
8.66
2.01
3.53
1.86
2.03
11.93
10.78
11.84
8.80
8.77
8.69
9.38
38.26
8.99
9.40
9.03
9.01
146.18
38.95
39.88
1.96
1.97
11.82
8.67
8.97
8.93
38.46
63.24
53.31
50.04
316.96
306.14
307.09t
306.14
To attain WR2 at reducer low speed shaft (output), multiply WR2 of reducer input by the exact ratio squared.
* Mercury/Mars 159.8 ratio is a triple reduction.
110
tech infoR2.p65
109
Black
7/19/2002, 11:05 AM
Operation of the reducer shall not differ from the application data warranted on the nameplate. Any change from this data requires submittal of new application
information along with all nameplate data to the factory for engineering approval. All data changes require a new nameplate be issued and installed on the
reducer. Note location of serial number and model number on the nameplate. When contacting the factory or sales representative, have the serial number and
model number available as these unique numbers fully describe the reducer and allow for the fastest and most accurate exchange of information.
Spare and Repair Parts
When ordering parts, always give complete data from the nameplate on the Planetgear
reducer. Model number and serial number information is necessary. Complete
nameplate data will assure that you are receiving the correct parts. If a new nameplate is received with the new parts, (as when a drive ratio is changed), replace the
old nameplate on the drive with the new nameplate for future reference. Sun gears
and carrier assemblies are stamped with a part number for easy identification.
Installation
All speed reducers should be mounted on a vibration-free, solid, level foundation.
The normal method of mounting is horizontal. However, the unit may be oriented in other positions, including vertical. Relocation of the oil fill, oil drain, and
oil level plugs may be necessary. Vertical mounting requires an oil reservoir kit.
Please indicate mounting orientation if other than horizontal when ordering.
Foundation, Steel
When mounting the unit on structural steel, use of a rigid baseplate is
strongly recommended. The baseplate should be designed to minimize
bending, twisting, and localized bending between stiffeners. The baseplate must be flat to prevent distortion of the reducer. The baseplate should
extend the entire length of the unit. Bolt the unit securely to the structural
steel support.
Foundation, Concrete
For best results, grout structural steel mounting pads into the mounting
base. The reducer is then installed and shimmed off the structural pads. If
shims are used to level or align the unit, they should be distributed evenly
under all mounting pads to equalize the support load. Use a feeler gauge
to determine thickness of required shims. All pads must be squarely supported to prevent distortion of the housing when the unit is bolted down.
Alignment
Align reducer with driven equipment by placing broad flat shims under all mounting pads of the reducer. Start at the low speed end and level across the length
and width of the reducer. Check with feeler gauge to make certain that all pads
are supported to prevent distortion of housing when reducer is bolted down.
After reducer is aligned with driven equipment and bolted down, align prime
mover to the reducer input shaft.
If reducer is received coupled to a motor, it has been aligned at the factory.
However, because alignment may have been disturbed in shipment, it is best to
check alignment and realign if necessary. The reliability and long life of the
reducer requires careful installation of accessories and accurate alignment of the
connecting shafts.
If the reducer is mounted onto a Planetgear baseplate and must be direct coupled
to a drive shaft, shimming should be done underneath the baseplate. Shim under
the baseplate until the baseplate is level and all feet are on the same plane.
After first week Check alignment of the total system and realign if necessary.
Also tighten all bolts and plugs as required. Remember to remove the load from
the system before attempting to service the reducer. This action reduces the
possibility of unexpected motion in the system. Check coupling for alignment
to make sure that setting or vibration has not caused excessive misalignment.
Coupling Alignment
Detailed instruction for installation of Rexnord Elastomer couplings are available from the factory, your Sales Engineer, or local distributor. The following
are general instruction:
Correct for angular misalignment by measuring the distance from coupling
hub (on motor shaft) to coupling hub (on reducer input shaft) at four places each
90 degrees apart. Adjust or shim until the four readings are equal.
Correct for parallel offset misalignment by placing a straight edge across the
hub flange in two places 90 degrees apart. Adjust or shim until the straight edge
lays flat on both ends.
Recheck for angular misalignment, adjust if necessary and tighten down the
connected equipment.
Install Elastomer center member elements. Tighten all cap screws to the
correct torque value listed in the coupling installation sheet.
Face Mounted Scoops
The scoops have been designed to accommodate the motor weight and the
starting torque based on the correct selections in this catalog and using standard
1750, 1430, 1170 and 950 AC motors. If a customer feels deflection is excessive, we suggest either placing a support under the end of the scoop, or drilling
a hole in the end of the face scoop and installing a jack screw.
Sprocket, Pulley and Sheave Connections
Mount power takeoff as close as possible to the gear case in order to reduce the
cantilever effect of overhung loads on the shaft bearings. If the power takeoff
has only one hub, that hub should be on the outside with the plate closest to the
seal cage of the reducer. Adjust belts or chains to manufacturer specifications to
prevent overtightening.
111
instmaintR2.p65
110
Black
7/19/2002, 10:46 AM
15F to 60F
50F to 125F
Viscosity
@ 4 0 C
Centistokes
90 - 110
135 - 165
AGMA
G r ad e #
ISO
G r ad e #
3
4
100
150
Operating Temperature
If the speed reducer operates under extreme conditions or is exposed to
large temperature fluctuations, the use of a synthetic oil is recommended.
Contact lubrication supplier for recommendations.
Note: The synthetic lubricant should conform to the requirements of
ANSI/AGMA 9005-D94.
If the speed reducer operates in an environment where the temperature
fluctuations are predictable, choose an oil viscosity that is recommended
for that given temperature (i.e. for cold weather operation, use an oil that
will circulate freely at all times). The pour point of the oil should be 9F(5C)
less than the minimum external temperature during reducer operation.
During hot weather, use a higher viscosity oil that will not thin out and lose
its lubricating qualities.
Special measures should be taken to protect drives operating in direct sunlight at ambient temperatures over 38F (100F). This protection can consist of a canopy over the drive or reflective paint on the drive. If neither is
possible, a heat exchanger or other cooling device may be required to prevent the reducer sump temperature from exceeding the allowable maximum oil temperature of 200F(93C).
Temperatures in excess of 120F(49C) feel hot to the human hand.
Planetgear reducers can be operated with reducer sump oil temperatures of
up to 200F (93C).
Oil Levels
Determine specific oil quantity needed. From the nameplate or
the oil capacity chart below, determine the quantity of oil in gallons needed to operate the reducer.
Reducer
Series
M ercury
M ars
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
Reduction Type
Single
0.25 (0.50)
0.25 (0.50)
3.8 (5.0)
3.8 (5.0)
5.0 (7.0)
6.8 (8.8)
7.8 (14.0)
12.0 (19.0)
13.0 (22.5)
Double
0.25 (0.50)
0.25 (0.50)
3.8 (5.0)
3.8 (5.0)
5.0 (7.0)
6.8 (8.8)
7.8 (14.0)
12.0 (19.0)
13.0 (22.5)
15.5 (34.0)
32.0
Triple
0.25 (0.50)
0.25 (0.50)
3.8 (5.0)
3.8 (5.0)
5.0 (7.0)
6.8 (8.8)
7.8 (14.0)
12.0 (19.0)
13.0 (22.5)
15.5 (34.0)
32.0
Quadruple
0.38 (0.61)
0.38 (0.61)
3.5 (4.5)
3.5 (4.5)
5.0 (7.0)
6.8 (8.8)
8.5 (15.5)
12.7 (20.0)
15.0 (25.5)
17.5 (38.0)
32.0
Quintuple
5.0 (7.0)
6.8 (8.8)
8.3 (15.3)
12.8 (21.0)
LUBRICATION CHANGES
Oil
For normal conditions, change oil every six months or 2,500 hours, whichever comes first. If operating under abnormal conditions such as high temperature, severe duty, moisture or particle contamination, oil may need to
be changed more frequently. Reference Owners' Manual for maintenance.
112
instmaintR2.p65
111
Black
7/19/2002, 10:46 AM
NON-HORIZONTAL SERVICE
Planetgear speed reducers can be installed on an incline or in the vertical orientation. Contact factory or sales representative if the
reducer is mounted in a rotated position with respect to the drive line.
Note: If any reducer application exceeds max. allowable tilt, consult factory or sales representative for possible modifications.
113
instmaintR2.p65
112
Black
7/19/2002, 10:46 AM
FIGURE 1
C-FACE SECTIONAL VIEWS
114
instmaintR2.p65
113
Black
7/19/2002, 10:46 AM
3
3
3
3
3
115
SpecR2.p65
114
Black
7/19/2002, 10:55 AM
Secondary reducer/motor
package offers an additional
10:1 reduction in inching mode.
116
SpecR2.p65
115
Black
7/19/2002, 10:55 AM
117
SpecR2.p65
116
Black
7/19/2002, 10:55 AM
118
SpecR2.p65
117
Black
7/19/2002, 10:55 AM
AREA
Circle
SOLID
SURFACE AREA
VOLUME
6a2
a3
lxwxh
4r 2
4r 3
3
2rh + 2r 2
r 2 h
Cube
r 2
circumference = 2r
Rectangular Prism
Ellipse
ab
Sphere
Triangle
ab
Cylinder
Square
a2
Cone
Rectangle
lw
+ h2
(+ r2 if you add
the base)
119
gen infoR2.p65
118
Black
7/19/2002, 10:42 AM
r 2 h
3
WEIGHT
FORMULA
VARIABLES
N=
VARIABLES
N = Speed of shaft rotation (rpm)
V
0.262D
TORQUE
TORQUE (T) = F x R (lb-in)
ACCELERATION / DECELERATION
OF TORQUE AND FORCE
F = Force (lbs)
R = Perpendicular distance from the
center of rotation to the force (in)
Rotating Objects
T=
(WK2)N
308t
HORSEPOWER (HP)
Rotating Objects
HP =
T x RPM
63,025
F=
WV
1,933t
W = Weight (lbs)
V = Change in velocity (fpm)
FxV
33,000
Hydraulic
HP =
GPM x PSI
1,714
TEMPERATURE
TO CONVERT FROM
TO
USE FORMULA
temperature Celsius, t C
temperature Kelvin, tK
temperature Fahrenheit, tF
temperature Kelvin, tK
tK = tC + 273.15
tK = (tF + 459.67) / 1.8
temperature Celsius, t C
temperature Fahrenheit, tF
tF = 1.8 tC + 32
temperature Fahrenheit, tF
temperature Celsius, tC
temperature Kelvin, t K
temperature Celsius, tC
tC = tK - 273.15
temperature Kelvin, t K
temperature Fahrenheit, tF
tF = 1.8 tK - 459.67
temperature Kelvin, t K
temperature Rankine, tR
tR = 9/5 tK
temperature Rankine, tR
temperature Kelvin, tK
tK = 5/9 tR
120
gen infoR2.p65
119
Black
7/19/2002, 10:42 AM
MULTIPLY:
centim eters
centim eters
feet
feet
feet
inches
inches
inches
kilom eters
m eters
m eters
m eters
m eters
m iles (U.S.)
m iles (U.S.)
m illim eters
m illim eters
y ards
TO OBTAIN:
feet
inches
m eters
centim eters
m illim eters
m eters
centim eters
m illim eters
m iles (U.S.)
inches
feet
y ards
m iles (U.S.)
m eters
kilom eters
feet
inches
m eters
MULTIPLY:
square centim eters
square centim eters
square feet
square feet
square feet
square inches
square inches
square inches
square m eters
square m eters
square m eters
square m illim eters
square m illim eters
AREA
BY
0.1550003
0.001076391
0.09290304*
929.0304
92,903.04*
645.16*
6.4516*
0.00064516*
1550.003
10.763910
1.195990
0.00001076391
0.001550003
TO OBTAIN:
square inches
square feet
square m eters
square centim eters
square m illim eters
square m illim eters
square centim eters
square m eters
square inches
square feet
square y ards
square feet
square inches
MULTIPLY:
cubic centim eters
cubic feet
cubic feet
gallons (U.K.)
gallons (U.K.)
gallons (U.S.)
gallons (U.S.)
cubic inches
cubic inches
cubic inches
liters
liters
liters
liters
cubic m eters
cubic m eters
cubic m eters
cubic m eters
cubic m eters
cubic m illim eters
VOLUME
BY
0.06102376
0.02831685
28.31685
0.004546092
4.546092
0.003785412
3.785412
16,387.06
16.38706
0.000016387
0.001*
0.2199692
0.2641720
0.03531466
219.9692
264.172
35.31466
1000.*
61,023.76
0.00006102
TO OBTAIN:
cubic inches
cubic m eters
liters
cubic m eters
liters
cubic m eters
liters
cubic m illim eters
cubic centim eters
cubic m eters
cubic m eters
gallons(U.K.)
gallons (U.S.)
cubic feet
gallons (U.K.)
gallons (U.S.)
cubic feet
liters
cubic inches
cubic inches
121
gen infoR2.p65
120
Black
7/19/2002, 10:42 AM
TO OBTAIN:
grains
kilogram s
pounds/cubic inch
gram s
ounces
ounces (troy )
pounds
slugs
tons (long)
tons (short)
tons (m etric)
pounds/cubic foot
pounds/gallon (U.K.)
pounds/gallon (U.S.)
gram s
kilogram s
kilogram s
kilogram s/cubic m eter
gram s/cubic centim eter
kilogram s/cubic m eter
kilogram s/cubic m eter
kilogram s
kilogram s
kilogram s
kilogram s
MULTIPLY:
kilogram s-force
new tons
new tons
new tons/m eter
new tons/m eter
pounds-force
pounds/inch
pounds/foot
TO OBTAIN:
new tons
kilogram s-force
pounds-force
pounds/inch
pounds/foot
new tons
new tons/m eter
new tons/m eter
MULTIPLY:
kilogram s-m eters
ounce-inches
ounce-inches
new ton-m eters
new ton-m eters
new ton-m eters
new ton-m illim eters
pound-feet
MULTIPLY:
bars
kilogram s/square centim eter
kilogram s/square m eter
kilogram s/square m eter
new tons/square centim eter
new tons/square m eter
new tons/square m eter
pounds/cubic foot
pounds/cubic inch
pounds/cubic inch
pounds/cubic inch
pounds/cubic inch
pounds/cubic inch
(CONTINUED)
MULTIPLY:
Btu (m ean)
calorie (m ean)
foot-pound
joule
joule
joule
joule
joule
joule (International U.S.)
joule (U.S. legal, 1948)
joule
w att-hour
TO OBTAIN:
joule
joule
joule
Btu (m ean)
calorie (m ean)
foot-pound
joule (International U.S.)
joule (U.S. legal, 1948)
joule
joule
w att-hour
joule
MULTIPLY:
Btu (International Talbe )hour
foot-pound/hour
foot-pound/m inute
horsepow er (550 ft-lb/s)
horsepow er (550 ft-lb/s)
horsepow er (electric)
horsepow er (m etric)
horsepow er (U.K.)
kilow att
w att
w att
w att
w att
w att
w att
w att
POWER
BY
0.2930711
0.000376616
0.02259697
0.7456999
745.6999
746*
735.499
745.7
1.341022
2655.224
44.25372
0.001341022
0.001340483
0.001359621
0.001341022
3.412141
TO OBTAIN:
w att
w att
w att
kilow att
w att
w att
w att
w att
horsepow er (550 ft-lb/s)
foot-pound/hour
foot-pound/m inute
horsepow er (550 ft-lb/s)
horsepow er (electric)
horsepow er (m etric)
horsepow er (U.K.)
Btu (International Table)/hour
MULTIPLY:
kilogram -m eters squared
kilogram -m eters squared
pound-feet squared
pound-inches squared
MOMENT OF INERTIA
BY
23.73036
3417.171
0.04214011
0.00029264
TO OBTAIN:
pound-feet squared
pound-inches squared
kilogram -m eters squared
kilogram -m eters squared
MULTIPLY:
kilogram -m eters/second
kilogram -m eters/second
pound-feet/second
pound-inches/second
MOMENTUM
BY
7.233011
86.79614
0.1382550
0.01152125
TO OBTAIN:
pound-feet/second
pound-inches/second
kilogram -m eters/second
kilogram -m eters/second
MULTIPLY:
centipoise
centistoke
m eters squared/second
m eters squared/second
pascal-second
pascal-second
poise
stoke
VISCOSITY
BY
0.001*
0.000001*
1,000,000
10,000.*
1000.*
10.*
0.1*
0.0001
TO OBTAIN:
pascal-second
m eters squared/second
centistoke
stoke
centipoise
poise
pascal-second
m eters squared/second
122
gen infoR2.p65
121
Black
7/19/2002, 10:43 AM
Shaft Diameters
O v er
Thru
7/16
9/16
9/16
7/8
7/8
1 1/4
1 1/4
1 3/8
1 3/8
1 3/4
D-
- W2
Key
WxH
1/8 x 1/8
3/16 x 3/16
1/4 x 1/4
5/16 x 5/16
3/8 x 3/8
Set
Screw
#10
1/4
5/16
3/8
3/8
Shaft Diameters
O v er
Thru
1 3/4
2 1/4
2 1/4
2 3/4
2 3/4
3 1/4
3 1/4
3 3/4
3 3/4
4 1/2
Key
WxH
1/2 x 1/2
5/8 x 5/8
3/4 x 3/4
7/8 x 7/8
1x1
Set
Screw
1/2
1/2
5/8
3/4
3/4
Shaft Diameters
O v er
Thru
4 1/2
5 1/2
5 1/2
6 1/2
6 1/2
7 1/2
7 1/2
9
9
11
Key
WxH
1 1/4 x 1 1/4
1 1/2 x 1 1/2
1 3/4 x 1 1/2
2 x 1 1/2
2 1/2 x 1 3/4
Set
Screw
7/8
1
-
Shaft Diameters
O v er
Thru
11
13
13
15
15
18
18
22
22
26
Key
WxH
3x2
3 1/2 x 2 1/2
4x3
5 x 3 1/2
6x4
BOLT TORQUES
SAE
0
1
2
3
0.0600
0.0730
0.0860
0.0990
64
56
48
0.00263
0.00370
0.00487
0.00218
0.00310
0.00406
80
72
64
56
0.00180
0.00278
0.00394
0.00523
0.00151
0.00237
0.00339
0.00451
4
5
6
8
0.1120
0.1250
0.1380
0.1640
40
40
32
32
0.00604
0.00796
0.00909
0.0140
0.00496
0.00672
0.00745
0.01196
48
44
40
36
0.00661
0.00830
0.01015
0.01474
0.00566
0.00716
0.00874
0.01285
10
12
1/4
5/16
0.1900
0.2160
0.2500
0.3125
24
24
20
18
0.0175
0.0242
0.0318
0.0524
0.01450
0.0206
0.0269
0.0454
32
28
28
24
0.0200
0.0258
0.0364
0.0580
0.0175
0.0226
0.0326
0.0524
3/8
7/16
1/2
9/16
0.3750
0.4375
0.5000
0.5625
16
14
13
12
0.0775
0.1063
0.1419
0.182
0.0678
0.0933
0.1257
0.162
24
20
20
18
0.0878
0.1187
0.1599
0.203
0.0809
0.1090
0.1486
0.189
5/8
3/4
7/8
1
0.6250
0.7500
0.8750
1.0000
11
10
9
8
0.226
0.334
0.462
0.606
0.202
0.302
0.419
0.551
18
16
14
12
0.256
0.373
0.509
0.663
0.240
0.351
0.480
0.625
1 1/4
1 1/2
1.2500
1.5000
7
6
0.969
1.405
0.890
1.294
12
12
1.073
1.581
1.024
1.521
123
gen infoR2.p65
122
Black
7/19/2002, 10:43 AM
TO FIND
ALTERNATING OR
DIRECT CURRENT
HP x 746
1.73 x E x Eff x pf
E/R
KW x 1,000
E x pf
KW x 1,000
1.73 x E x pf
IR
E/I
Kva x 1,000
E
Kva x 1,000
1.73 x E
Kilowatts
I x E x pf
1,000
1.73 x I x E x pf
1,000
Kva
IxE
1,000
1.73 x I x E
1,000
Horsepower = (Output)
I x E x Eff x pf
746
1.73 x I x E x Eff x pf
746
TO FIND
Single-Phase
Three-Phase
HP x 746
E x Eff x pf
I = Amperes
E = Volts
Eff = Efficiency
pf = Power Factor
KW = Kilowatts
R = Ohms
Kva = Kilovolt Amperes
Alternating
Current
Single
Three
Phase
Phase
4.9
2.0
8.0
3.4
10.0
4.8
12.0
6.2
17.0
8.6
DC
HP
2.7
4.8
6.6
8.5
12.5
5
7 1/2
10
15
20
Alternating
Current
Single
Three
Phase
Phase
28
14.4
40
21.0
50
26.0
38.0
50.0
DC
HP
20
29
38
56
74
25
30
40
50
60
DC
HP
92
110
146
180
215
75
100
125
150
200
Alternating
Current
Single
Three
Phase
Phase
180
240
300
360
480
DC
268
355
443
534
712
Alternating
Current
Single
Three
Phase
Phase
60
75
100
120
150
230 x 100
550
I=
= 42 amps
Power Factor estimated at 80% for most motors. Efficiency is usually 80-90%.
25
15
30
20
gen infoR2.p65
U-Frame
No.
182
184
213
215
254U
256U
284U
286U
324U
324S
326U
326S
123
Black
U
7/8
7/8
1 1/8
1 1/8
1 3/8
1 3/8
1 5/8
1 5/8
1 7/8
1 5/8
1 7/8
1 5/8
Shaft Keyseat
Width Depth
3/16
3/32
3/16
3/32
1/4
1/8
1/4
1/8
1/4
1/8
1/4
1/8
3/8
3/16
3/8
3/16
1/2
1/4
3/8
3/16
1/2
1/4
3/8
3/16
Key
Length
1 3/8
1 3/8
2
2
2 3/4
2 3/4
3 3/4
3 3/4
4 1/4
1 7/8
4 1/4
1 7/8
N-W
2 1/4
2 1/4
3
3
3 3/4
3 3/4
4 7/8
4 7/8
5 5/8
3 1/4
5 5/8
3 1/4
Horsepower Ratings
1800
1200
40
25
50
30
60
40
75
50
100
60
125
75
U-Frame
No.
364U
364US
365U
365US
404U
404US
405U
405US
444U
444US
445U
445US
7/19/2002, 10:43 AM
U
2 1/8
1 7/8
2 1/8
1 7/8
2 3/8
2 1/8
2 3/8
2 1/8
2 7/8
2 1/8
2 7/8
2 1/8
Shaft Keyseat
Width Depth
1/2
1/4
1/2
1/4
1/2
1/4
1/2
1/4
5/8
1/4
1/2
1/4
5/8
1/4
1/2
1/4
3/4
3/8
1/2
1/4
3/4
3/8
1/2
1/4
Key
Length
5
2
5
2
5 1/2
2 3/4
5 1/2
2 3/4
7
2 3/4
7
2 1/4
N-W
6 3/8
3 3/4
6 3/8
3 3/4
7 1/8
4 1/4
7 1/8
4 1/4
8 5/8
4 1/4
8 5/8
4 1/4
124
100
60
50
100
60
50
100
125
75
60
100
125
75
60
125
150
100
75
125
150
100
75
150
200
125
100
150
200
125
100
TEFC
Shaft Keyseat
T-Frame
No.
143T
145T
182T
184T
213T
215T
254T
256T
284T
284T S
286T
286T S
324T
324T S
326T
326T S
364T
364T S
365T
365T S
404T
404T S
405T
405T S
444T
444T S
445T
445T S
447T
447T S
449T
449T S
0.875
0.875
1.125
1.125
1.375
1.375
1.625
1.625
1.875
1.625
1.875
1.625
2.125
1.875
2.125
1.875
2.375
1.875
2.375
1.875
2.875
2.125
2.875
2.125
3.375
2.375
3.375
2.375
3.375
2.375
3.375
2.375
Key
N-W *
Width Depth Length
0.19
0.19
0.25
0.25
0.31
0.31
0.38
0.38
0.50
0.38
0.50
0.38
0.50
0.50
0.50
0.50
0.63
0.50
0.63
0.50
0.75
0.50
0.75
0.50
0.88
0.63
0.88
0.63
0.88
0.63
0.88
0.63
0.09
0.09
0.13
0.13
0.16
0.16
0.19
0.19
0.25
0.19
0.25
0.19
0.25
0.25
0.25
0.25
0.31
0.25
0.31
0.25
0.38
0.25
0.38
0.25
0.44
0.31
0.44
0.31
0.44
0.31
0.44
0.31
1.38
1.38
1.75
1.75
2.38
2.38
2.88
2.88
3.25
1.88
3.25
1.88
3.88
2.00
3.88
2.00
4.25
2.00
4.25
2.00
5.63
2.75
5.63
2.75
6.88
3.00
6.88
3.00
6.88
3.00
6.88
3.00
2.25
2.25
2.75
2.75
3.38
3.38
4.00
4.00
4.63
3.25
4.63
3.25
5.25
3.75
5.25
3.75
5.88
3.75
5.88
3.75
7.25
4.25
7.25
4.25
8.50
4.75
8.50
4.75
8.50
4.75
8.50
4.75
A
Max.
B
Max.
BA
7.00
7.00
9.00
9.00
10.50
10.50
12.50
12.50
14.00
14.00
14.00
14.00
16.00
16.00
16.00
16.00
18.00
18.00
18.00
18.00
20.00
20.00
20.00
20.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
6.00
6.00
6.50
7.50
7.50
9.00
10.75
12.50
12.50
12.50
14.00
14.00
14.00
14.00
15.50
15.50
15.25
15.25
16.25
16.25
16.25
16.25
17.75
17.75
18.50
18.50
20.50
20.50
23.00
23.00
28.00
28.00
12.63
12.63
12.75
13.75
15.81
17.31
20.50
22.25
23.31
22.00
24.88
23.50
26.50
24.63
27.75
26.13
28.75
26.56
29.75
27.56
32.63
29.63
34.13
31.13
37.88
34.13
39.88
36.13
43.25
39.50
48.25
44.50
3.50
3.50
4.50
4.50
5.25
5.25
6.25
6.25
7.00
7.00
7.00
7.00
8.00
8.00
8.00
8.00
9.00
9.00
9.00
9.00
10.00
10.00
10.00
10.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
2.75
2.75
3.75
3.75
4.25
4.25
5.00
5.00
5.50
5.50
5.50
5.50
6.25
6.25
6.25
6.25
7.00
7.00
7.00
7.00
8.00
8.00
8.00
8.00
9.00
9.00
9.00
9.00
9.00
9.00
9.00
9.00
2.00
2.50
2.25
2.75
2.75
3.50
4.13
5.00
4.75
4.75
5.50
5.50
5.25
5.25
6.00
6.00
5.63
5.63
6.13
6.13
6.13
6.13
6.88
6.88
7.25
7.25
8.25
8.25
10.00
10.00
12.50
12.50
0.34
0.34
0.41
0.41
0.41
0.41
0.53
0.53
0.53
0.53
0.53
0.53
0.66
0.66
0.66
0.66
0.66
0.66
0.66
0.66
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
2.25
2.25
2.75
2.75
3.50
3.50
4.25
4.25
4.75
4.75
4.75
4.75
5.25
5.25
5.25
5.25
5.88
5.88
5.88
5.88
6.63
6.63
6.63
6.63
7.50
7.50
7.50
7.50
7.50
7.50
7.50
7.50
7.00
7.00
9.00
9.00
10.50
10.50
12.50
12.50
14.00
14.00
14.00
14.00
16.00
16.00
16.00
16.00
18.00
18.00
18.00
18.00
20.00
20.00
20.00
20.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
22.00
NOTE: Suffix "S" indicates short shaft for direct coupled service only. Motors of 25 hp and up listed as T-Frame may also be available in TS-Frames.
These dimensions are not NEMA standard, but they are average and common to a number of manufactures for Open (Drip Proof) motors. TEFC motors will be up to
5 inches longer, and may be slightly taller (less than an inch difference).
* Usable length of shaft "V" is 1/4 inch shorter than "N-W".
125
gen infoR2.p65
124
Black
7/19/2002, 10:44 AM
AJ
AK
BA
BB
min.
BC
BD
max.
56C
143TC and 145TC
182TC and 184TC
182TCH and 184TCH
213TC and 215TC
254TC and 256TC
284TC and 286TC
284TSC and 286TSC
324TC and 326TC
324TSC and 326TSC
364TC and 365TC
364TSC and 365TSC
404TC and 405TC
404TSC and 405TSC
444TC and 445TC
444TSC and 445TSC
5.875
5.875
7.250
5.875
7.250
7.250
9.000
9.000
11.000
11.000
11.000
11.000
11.000
11.000
14.000
14.000
4.500
4.500
8.500
4.500
8.500
8.500
10.500
10.500
12.500
12.500
12.500
12.500
12.500
12.500
16.000
16.000
2.75
2.75
3.50
3.50
4.25
4.75
4.75
4.75
5.25
5.25
5.88
5.88
6.62
6.62
7.50
7.50
0.16
0.16
0.25
0.16
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
-0.19
0.12
0.12
0.12
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
6.50
6.50
9.00
6.50
9.00
10.00
11.25
11.25
14.00
14.00
14.00
14.00
15.50
15.50
18.00
18.00
BF (hole)
Number
Bolt
of
Tap Size Penetration
Holes
Allowance
4
3/8-16
4
3/8-16
0.56
4
1/2-13
0.75
4
3/8-16
0.56
4
1/2-13
0.75
4
1/2-13
0.75
4
1/2-13
0.75
4
1/2-13
0.75
4
5/8-11
0.94
4
5/8-11
0.94
8
5/8-11
0.94
8
5/8-11
0.94
8
5/8-11
0.94
8
5/8-11
0.94
8
5/8-11
0.94
8
5/8-11
0.94
Shaft Keyseat
AH
2.06
2.12
2.62
2.62
3.12
3.75
4.38
3.00
5.00
3.50
5.62
3.50
7.00
4.00
8.25
4.50
0.625
0.875
1.125
1.125
1.375
1.625
1.875
1.625
2.125
1.875
2.375
1.875
2.875
2.125
3.375
2.375
Width
Depth
Key
Length
0.19
0.19
0.25
0.25
0.31
0.38
0.50
0.38
0.50
0.50
0.63
0.50
0.75
0.50
0.88
0.63
0.09
0.09
0.13
0.13
0.16
0.19
0.25
0.19
0.25
0.25
0.31
0.25
0.38
0.25
0.44
0.31
1.38
1.38
1.75
1.75
2.38
2.88
3.25
1.88
3.88
2.00
4.25
2.00
5.63
2.75
6.88
3.00
126
gen infoR2.p65
125
Black
7/19/2002, 10:44 AM
IEC STANDARDS Many countries have adopted IEC Standards, IEC stands for "The International Electrotechnical Commission". The object of the
commission is to facilitate the coordination and unification of National Electrotechnical Standards.
IEC motors are in service worldwide. The standards have been incorporated into individual national standards. Outputs are in KW and dimensions
are in millimeters. Table below shows the common IEC frame sizes of one motor manufacturer.
Mechanically, the major mounting dimensions of NEMA vs IEC are similar. Each standard has adopted units of dimensions predominant with the
country used in.
11, 15
18.5
22
30, 37
45
55
75
90
110
132
KW R a ting
IEC Fra me No.*
R PM
D
C
U
(mm)
(mm)
1500 1000
750
.25, .37
80
19
1.1
0.75
90
S
24
1.5
1.1
90
L
24
2.2, 3
1.5
.75, 1.1
100
L
28
4
2.2
1.5
112
M
28
5.5
3
2.2
132
S
38
7.5
4, 5.5
3
132
M
38
11
7.5
4, 5.5
160
M
42
15
11
7.5
160
L
42
18.5
180
M
48
22
15
11
180
L
48
30
18.5, 22
15
200
L
55
37
18.5
225
S
60
225
M
55
45
30
22
225
M
60
250
M
60
55
37
30
250
M
65
280
S
65
75
45
37
280
S
75
280
M
65
90
55
45
280
M
75
315
S
65
110
75
55
315
S
80
315
M
65
132
90
75
315
M
80
N-W
(mm)
E
(mm)
F
(mm)
BA
(mm)
40
50
50
60
60
80
80
110
110
110
110
110
140
110
140
140
140
140
140
140
140
140
170
140
170
63
70
70
80
95
108
108
127
127
140
140
159
178
178
178
203
203
229
229
229
229
254
254
254
254
50
50
62
70
70
70
89
105
127
120
140
152
143
156
156
174
174
184
184
210
210
203
203
228
228
50
56
56
63
70
89
89
108
108
121
121
133
149
149
149
168
168
190
190
190
190
216
216
216
216
* IEC frame sizes are made up of shaft height, (mm), length (letter) and shaft diameter (mm), for
example 90S-24. Three frame lengths may be offered, S = Short, M = Medium, L = Long.
KEY SIZES
Sha ft Size Dia . Sha ft Le ngth
Ke y Size
U
(N-W)
(Squa re : W, H)
(mm)
(mm)
(mm)
7
16
2
9
20
3
11
23
4
14
30
5
16
40
5
18
40
6
19
40
6
22
50
6
24
50
8
28
60
8
32
80
10
38
80
10
42
110
12
48
110
14
55
110
16
60
140
18
65
140
18
70
140
20
75
140
20
80
170
22
85
170
22
90
170
25
95
170
25
100
210
28
110
210
28
127
gen infoR2.p65
126
Black
7/19/2002, 10:44 AM
128
UA
E
A
- SEE TABLE 5, PAGES 85-92 * Ratios listed may not be available in all
speed reducer series
Series
Mercury
M ar s
Venus
Atlas
Earth
Polaris
Neptune
Orion
Saturn
Titan
Jupiter
11.75
11.75
18.00
18.00
23.25
23.25
29.25
29.25
33.00
33.25
33.25
15.13
15.13
11.75
11.75
11.75
14.00
11.69
19.62
14.75
19.86
28.88
C*
s,d,t
22.13
23.50
29.73
30.73
34.08
36.30
42.80
46.21
50.03
51.78
62.94
quad
24.38
25.75
28.52
29.52
35.71
37.92
42.69
46.11
52.50
54.25
62.94
6.25
6.25
7.75
7.75
8.75
10.00
11.25
11.25
12.88
12.88
16.50
4.19
4.19
8.00
8.00
9.88
9.88
12.88
12.88
14.63
14.63
14.63
9.41
9.41
9.53
9.53
9.53
11.75
8.19
16.00
11.00
16.00
12.50
Low Speed
Shaft
Series
2
Black
9.91
9.91
13.50
13.50
15.94
17.19
20.94
20.94
24.25
24.25
31.50
6.59
7.46
8.63
9.63
11.38
11.29
18.83
14.37
22.04
18.74
20.88
7.32
7.32
11.50
11.50
14.38
14.38
19.38
19.38
22.75
22.75
30.00
w/o fan
s,d,t
quad
4.15
2.000
3.00
3.00
Mercury
4.98
2.500
3.50
3.50
M ar s
1.00
5.50
2.750
4.25
3.50
Venus
1.00
6.50
3.250
4.25
3.50
Atlas
1.00
7.00
3.500
4.50
4.25
Earth
1.00
8.00
4.000
4.50
4.25
Polaris
1.00
9.00
4.500
5.68
4.50
Neptune
1.00
10.00
5.000
5.68
4.50
Orion
1.00
11.00
5.500
6.50
5.68
Saturn
1.00
11.25
6.500
6.50
5.68
Titan
3.50
12.25
7.250
6.50
6.50
Jupiter
* Mercury and Mars: Add 0.66 in. with backstop
* Venus Quad: Add 0.66 in. with backstop
* Atlas Quad: Add 0.66 in. with backstop
w/ fan
s,d,t
quad
1.88
1.88
2.38
2.38
2.88
2.50
2.88
2.50
3.25
2.88
2.88
2.88
3.56
3.25
3.56
3.25
4.38
3.56
4.38
3.56
4.38
4.38
129
quickR2.p65
H
bolt
7/8
7/8
1
1
1
1
1 1/4
1 1/4
1 1/2
1 1/2
1 1/2
7/19/2002, 10:49 AM
Avg. Wt.
Lbs.
UA
s,d,t
1.375
1.625
1.875
1.875
2.125
2.125
2.500
2.500
3.000
3.000
3.000
quad
1.375
1.625
1.625
1.625
1.875
1.875
2.125
2.125
2.500
2.500
3.000
144
150
295
325
481
702
923
1146
1512
2000
3470
Rexnord are registered trademarks of Rexnord Industries, LLC. Planetgear is a trademark of Rexnord.
All rights reserved.
CHINA
Rexnord China
Shanghai, China
Phone: 86-21-62701942
Fax: 86-21-62701943
BRAZIL
Rexnord Correntes Ltda.
Sao Leopoldo - RS
Phone: 55-51-579-8022
Fax: 55-51-579-8029
EUROPE
Rexnord NV/SA
Mechelen, Belgium
Phone: 32-15-.443811
Fax: 32-15-443860
CANADA
Rexnord Canada Ltd.
Scarborough, Ontario
Phone: 1-416-297-6868
Fax: 1-416-297-6873
Rexnord Industries, LLC, Gear Group, 3001 West Canal Street, Milwaukee, WI 53208-4200 USA
Phone: 414-342-3131
Fax: 414-937-4359
2007 Rexnord Industries LLC
LATIN AMERICA
Rexnord International, Inc.
Milwaukee, Wisconsin
Phone: 1-414-643-2366
Fax: 1-414-643-3222
E-mail: international2@rexnord.com
MEXICO
Rexnord S.A. de C.V.
Queretaro, Qro.
Phone: 52-442-218.5000
Fax: 52-.442-218-1090
SINGAPORE
Rexnord International, Inc.
Singapore City, Singapore
Phone: 65-6338-5622
Fax: 65-6338-5422
UNITED STATES
Customer Service
Phone: 1-866-REXNORD
(1-866-739-6673)
Fax: 1-614-675-1898
E-mail: rexnordcs(state)@rexnord.com
Example: rexnordcsohio@rexnord.com
ALL COUNTRIES NOT LISTED
Rexnord International
Milwaukee, Wisconsin
Phone: 1-414-643-2366
Fax: 1-414-643-3222
E-mail: international1@rexnord.com
2505