1396 Rev. H
Issue Date: March 2000
Rev. Date: May 2004
TABLE OF CONTENTS
1.0
INTRODUCTION
2.0
FEATURES
3.0
CERTIFICATION
4.0
OPERATION
5.0
ROUTINE MAINTENANCE
6.0
7.0
FIELD TESTING
8.0
9.0
Unit
1396
Rev.
Page 1 of 41
3.0 CERTIFICATION - Testing - All BOPs are hydrostatic and function tested per API 6A.
H2S Service - Materials in contact with pressured well fluids conform to NACE Specification MR-01-75
for H2S Service.
Arctic Service - In addition to the NACE Specifications above meets the API 6A with Charpy Impacts
at -50EF.
North Sea Service - In addition to the NACE Specification s and API requirements additional Charpy
Impact and NDE are carried out. A Design Review and Certificate of Compliance by DNV, Lloyds, or
Bureau Veritas are furnished with the Data Book.
4.0 OPERATION
Ram Open and Close - Before opening the rams be sure the lock screws are backed fully out (turn
counter clockwise). If lock screws do not turn out easily after a closed and locked wellbore pressure
test apply 1,500 to 3,000 psi hydraulic pressure to the "CLOSE" hydraulic port to relieve the load from
the end of the tail rod.
To open the rams apply 1,500 psi hydraulic pressure to the body port marked "OPEN". Close the rams
by applying 1,500 to 3,000 psi hydraulic pressure to the body port marked "CLOSE".
Bonnet Open and Close - Remove the bonnet bolts (23).
Unit
1396
Rev.
Page 2 of 41
To open the bonnets apply 500 to 1,500 psi hydraulic pressure to the body port marked "CLOSE" (ram
close). To close the bonnets apply 1,500 psi operating pressure to the body port marked "OPEN" (ram
open). After closing the bonnets maintain the 1,500 psi hydraulic pressure to keep the bonnet pulled
tightly against the body as the bonnet bolts are reinstalled.
Ram Change -
Remove the bonnet bolts and open the bonnets as described above. Maintain hydraulic pressure until
the bonnets have fully retracted and the rams have fully extended making them accessible. Vent all
hydraulic pressure to zero to prevent personal injury in the event that the bonnet is closed prematurely
during the ram change procedure. As an added safety precaution install the ram change rod covers
(9601-3036) to prevent the accidental closure of the bonnets as well as to prevent damage to the ram
change rods.
Remove the ram by lifting up and over the ram change rod. NOTE: Do not scratch ram change rods.
Front and rear seals may be replaced without fully removing the rams. Lift the ram up until it clears the
ram guide rod and rotate slightly to gain access to the front seal.
SPECIAL OPERATING INSTRUCTIONS - LARGE BORE SHEAR SEAL
Reference Drawings 2000-5001 & ES36-T010
The large bore shear seal BOP is equipped with pressure reducing regulators on the ram open
hydraulic circuit to prevent damage in the event ram open pressure is applied while the rams are
sealing wellbore pressure. During operation, the reducing regulator should be set at 1000 psi or less.
During ram change operations, it may be necessary to increase the pressure setting on the regulator
to fully close the bonnet. It may take as much as 1500 to 2000 psi to fully close the bonnets against
the body. After the ram change operation is complete, the regulator should be reset to its 1000 psi
operating setting.
Unit
1396
Rev.
Page 3 of 41
Unit
1396
Rev.
Page 4 of 41
Unit
1396
Rev.
Page 5 of 41
Unit
1396
Rev.
Page 6 of 41
Unit
1396
Rev.
Page 7 of 41
Unit
1396
Rev.
Page 8 of 41
Remove o-rings (13) from body. Remove ram change rods (6) and (7) from bonnet (1). Remove Tseals (18) from ram change rods (6) and (7). Remove o-rings (15) and (16), seals (20) and retainers
(21) from bonnet (1). Remove bushings (11) and seals (14) from bonnet (1). Clean and inspect all
parts for wear before reassembly.
Assembly -Typical reverse order of disassembly - pay careful attention to ram change rod surface do not scratch.
Install T-seals (18) into ram change rods (6) and (7). Install seals (14) and thread bushings (11) into
bonnet (1). Install seals (20), retainers (21) and o-rings (15) and (16), into bonnet (1). Install ram
change rods (6) and (7) through bonnet (1). NOTE: Do not scratch surfaces of ram change rods.
Install o-rings (13) into body. Support weight of bonnet (1) and thread ram change rods (6) and (7)
into body. NOTE: Ram change rods have different threads (6) = .875-9UNC, (7) = 1.000-8UNC.
Install T-seal (17) onto piston (5). Install piston (5) into bonnet (1). Install rod head (8)and secure with
Loctite #242 blue. Install main cylinder (4) and change cylinders (3). Install seal (20), retainer (21)
and o-rings (15) and (16), into end cap (2). Install indicator rod seal (33) and retainer (34) into end
cap (2).
Position indicator rod (32) into groove on piston (5) and align into end cap (2). Upon installation of end
cap onto main cylinder (4) and change cylinders (3), secure with socket head cap screws (25) and
(26). Install seal (61) and spacer (35) into pressure balance chamber (30).
Install pressure balance chamber (30) onto end cap (2). Secure with socket head cap screws (31).
Install bonnet seal (24 & 29). Actuator can now be tested and functioned per 4.0 Operation.
SHEAR SEAL ACTUATOR - Reference Drawing 9905-2002
Disassembly - Open the bonnets per 4.0 Operation and vent all hydraulic pressure to zero. Remove
rams; remove bonnet seal (24 & 29). Remove socket head cap screws (37) and end cap (2) from
secondary cylinder (49). Remove socket head cap screw (47) and remove slide (46) from end cap
(2). Remove retainer (43) from lock screw (50) and remove lock screw (50) from slide (46). Remove
SHBS (44) and remove leaf spring (45) from slide (46).
Remove o-ring (41), retainer (21) and seal (20) from end cap (2). Remove secondary rod (36) and
secondary piston (48). Remove T-seals (39 & 40) from secondary piston (48). Remove secondary
cylinder (49). Remove o-rings (13, 15, & 16), retainer (21) and seal (20) from secondary cylinder (49).
Remove main cylinder (4) and change cylinders (3). Remove main rod (38) from main piston (5).
Remove main piston (5) and T-seal (17). Remove guide (60) from main rod (38).
Support the weight of bonnet (1) and remove ram change rod (6 & 7) from body with allen wrench.
CAUTION: Do not scratch surfaces of ram change rods. NOTE: Specific location of change rods as
they have differing thread sizes. Remove o-rings (13) from body.
Remove ram change rods (6 & 7) from bonnet (1). Remove T-seals (18) from ram change rods (6 &
7). Remove o-rings (15 & 16), seals (20) and retainers (21) from bonnet (1). Remove bushings (11)
and seals (14) from bonnet (1). Clean and inspect all parts for wear before reassembly.
Assembly - Typical reverse order of disassembly. Install seals (14) and thread bushings (11) into
bonnet (1). Install seals (20), retainers (21) and o-rings (15 & 16) into bonnet (1). Insert ram change
rods (6 & 7) through bonnet (1). CAUTION: Pay careful attention to ram change rod surface - do not
scratch. Install o-rings (13) into body.
Unit
1396
Rev.
Page 9 of 41
Support weight of bonnet (1) and thread ram change rods (6 & 7) into body. NOTE: Ram change rods
have different threads (6) = .875-9UNC, (7) = 1.000-8UNC. Install T-seals (18) onto change rods (6
& 7). Install T-seal (17) onto piston (5). Install guide (60) onto main rod (38). Insert main rod (38) into
bonnet (1); thread main piston (5) onto main rod (38). Install main cylinder (4) and change cylinders
(3).
Install seals (20), retainers (21) and o-rings (13, 15, & 16) into secondary cylinder (49). Install
secondary cylinder (49) onto main cylinder (4) and change cylinders (3). Thread secondary rod (36)
into main piston (5).
Install o-rings (41), retainer (21) and seal (20) into end cap (2). Upon installation of end cap (2) onto
secondary cylinder (49), secure with socket head cap screws (37). Thread lock screw (50) into slide
(46) and secure with retainer (43). Attach leaf spring (45) to slide (46) with SHBS (44). Install slide
(46) into end cap (2) to full close position. Secure slide (46) into end cap (2) with socket head cap
screw (47). Install bonnet seal (24 & 29). Actuator can now be tested and functioned per 4.0
Operation.
LARGE BORE SHEAR SEAL ACTUATOR - Reference Drawing 2000-5001
Disassembly - Open the bonnets per 4.0 Operation and vent all hydraulic pressure to zero. Remove
rams; remove bonnet seal (24 & 29). Remove socket head cap screws (40) and end cap (2) from
cylinder (4). Remove socket head cap screw (47) and remove slide (46) from end cap (2). Remove
retainer (43) from lock screw (50) and remove lock screw (50) from slide (46). Remove SHBS (44)
and remove leaf spring (45) from slide (46).
Remove o-ring (16), retainer (21) and seal (20) from end cap (2). Remove cylinder (4) and change
cylinders (3), secondary rod (36) and lock collar (49) from inner piston (5). Remove outer piston (48)
form inner piston (5) and replace o-rings (39) and T-seal (17). Remove guide (60) and head (8).
Remove piston rod (38) from bonnet (1).
Support the weight of bonnet (1) and remove ram change rod (6 & 7) from body with allen wrench.
CAUTION: Do not scratch surfaces of ram change rods. NOTE: Specific location of change rods as
they have differing thread sizes. Remove o-rings (13) from body.
Remove ram change rods (6 & 7) from bonnet (1). Remove T-seals (18) from ram change rods (6 &
7). Remove o-rings (15 & 16), seals (20) and retainers (21) from bonnet (1). Remove bushings (11)
and seals (14) from bonnet (1). Clean and inspect all parts for wear before reassembly.
Assembly - Typical reverse order of disassembly.
COMBI PIPE SLIP ACTUATOR - Reference Drawing 9905-2003
Disassembly - Open the bonnets per 4.0 Operation and vent all hydraulic pressure to zero. Remove
rams and remove rod head (8). Remove bonnet seal (24 & 29). Remove socket head cap screws (31)
and housing (51) from end cap (2). Remove socket head cap screws (25 & 26).
Remove end cap (2) and indicator rod (32). CAUTION: Do not scratch inside surface of main cylinder
(4) when removing indicator rod. Remove o-rings (15 & 16), seal (20) and retainer (21) from end cap
(2). Remove indicator rod seal (33) and retainer (34) from end cap (2). Remove change cylinders (3)
and main cylinder (4) from bonnet (1). Remove piston (5) and T-seal (17) from bonnet (1).
Support weight of bonnet (1) and remove ram change rod (6 & 7) from body with allen wrench.
CAUTION: Do not scratch surfaces of ram change rods. NOTE: Specific location of change rods as
they have differing thread sizes.
Unit
1396
Rev.
Page 10 of 41
Remove o-rings (13) from body. Remove ram change rods (6 & 7) from bonnet (1). Remove T-seals
(18) from ram change rods (6 & 7). Remove o-rings (15 & 16), seals (20) and retainers (21) from
bonnet (1). Remove bushings (11) and seals (14) from bonnet (1). Clean and inspect all parts for
wear before reassembly.
Assembly - Typical reverse order of Disassembly. Install seals (14) and thread bushings (11) into
bonnet (1). Install seals (20), retainers (21) and o-rings (15 & 16) into bonnet (1). Insert ram change
rods (6 & 7) through bonnet (1). CAUTION: Pay careful attention to ram change rod surface - do not
scratch. Install T-seals (18) onto change rods (6 & 7). Install o-rings (13) into body.
Support weight of bonnet (1) and thread ram change rods (6 & 7) into body. Note: Ram change rods
have different threads (6) = .875-9UNC, (7) = 1.000-8UNC. Install T-seal (17) onto piston (5). Install
piston (5) into bonnet (1). Install rod head (8) secure with Loctite #242 blue. Install main cylinder (4)
and change cylinders (3).
Install seals (20), retainers (21) and o-rings (15 & 16) into end cap (2). Install indicator seal (33) and
retainer (34) into end cap (2). Position indicator rod (32) into groove on piston (5) and align into end
cap (2), upon installation of end cap onto main cylinder (4) and change rods (3). Secure with socket
head cap screws (25 & 26).
Attach housing (51) to end cap (2) and secure with socket head cap screw (31). Install bonnet seal
(24 & 29). Actuator can now be tested and functioned per 4.0 Operation.
6.0 RECOMMENDED MAINTENANCE PROGRAM
After Each Job - Inspect Ram Rubber Seals
Normal wear will be a moderate amount of extrusion downstream of the pressured side.
Replace the ram seals when usage has resulted in any noticeable loss of rubber. Field testing only
to the maximum anticipated well pressure will extend the life of the seals.
Inspect Bonnet Seal - Any extrusion indicates improper tightening of the bonnet bolts. Extrusion all
around the o-ring indicates even, but inadequate tightening of the bonnet nuts. Extrusion over only
a part of the o-ring indicates uneven tightening of the bonnet bolts. Replace if any extrusion is evident.
Check cutting edges of the shear or shear seal inserts. If the blade is chipped then the cutting action
of the insert may be impaired and therefore it should be discarded.
Check the teeth of the slip inserts. If the slip teeth are blunt or dulled then the gripping action of the
ram may be impaired and therefore the slips should be discarded.
Always store and operate the BOP with the equalizing valve closed.
After 20 Jobs or 12 Months Maximum - Completely disassemble the equalizing valve, replace all
seals and worn parts.
Completely disassemble and inspect the bonnet assemblies. Replace all seals and worn parts.
Inspect all threads, connections, bushings and fittings. Replace and repair as required.
Unit
1396
Rev.
Page 11 of 41
Unit
1396
Rev.
Page 12 of 41
Part Name
Qty.
H2S -50F
Part No.
Body
Single
2000-2900B
2000-5000B
Dual
2000-4680B
Quad
2000-2800B
Quint
2000-4690B
7949-1844B
Nuts
7937-0818B
7949-1437B
Nuts
7937-0514B
Single
ES46-SCG1
ES46-SCG1
Dual
ES46-SNG1
Quad
ES46-SCG1
Quint
ES36-SLG1
7934-9094
Studs
Connector Guards
Qty.
H2S -50F
Part No.
Single
2000-1900B
2000-1900B
Dual
2000-4700B
2000-4700B
Quad
9908-2600B
9908-2600B
Quint
2000-1220B
2000-1220B
Part Name
Body
Studs
Studs - Studded Flange Up
7949-2260B
Nuts
7937-0822B
7949-1437B
Nuts
7937-0514B
ES46-SCG1
Connector Guards
Single
Unit
1396
Rev.
Page 13 of 41
Part Name
Qty.
Dual
ES46-SNG1
Quad
ES46-SLG1
Quint
ES36-SLG1
7934-9094R
Qty.
Part No.
2000-3260
H2S -50F
Part No.
Unit
1396
Rev.
Page 14 of 41
Item No
Part Name
Qty.
H2S -50F
Part No.
Bonnet
9905-2824B
9905-2824B
End Cap
9905-2825B
9905-2825B
Change Cylinder
9905-2826B
9905-2826B
Main Cylinder
9905-2827B
9905-2827B
Piston
9905-2861XB
9905-2861XB
9905-2829B
9905-2829B
9905-2828B
9905-2828B
Rod Head
9905-2833B
9905-2833B
Lock Screw
9905-2832B
9905-2832B
10
Hand Wheel
9905-2851
9905-2851
11
Bushing
9905-2835
9905-2835
12
Guide Plate
9905-2857
9905-2857
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A248
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
19
Bushing
7830-0087
7830-0087
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
22
9905-2858
9905-2858
23
Bonnet Bolts
9905-2834B
9905-2834B
24
O-Ring
7813-3355
7813-A355
25
9905-1234G
9905-1234G
26
9905-0838G
9905-0838G
27
Plug, SAE
7934-0202
7934-0202
28
Nut
7938-0510
7938-0510
29
Back-Up Ring
9905-2859
9905-2859
60
Guide
2001-0025B
2001-0025B
62
O-Ring
7813-3148
7813-A148
63
7981-0302
7981-0302
Unit
1396
Rev.
Page 15 of 41
Unit
1396
Rev.
Page 16 of 41
Item No
Part Name
Qty.
H2S -50F
Part No.
Bonnet
9905-2841B
9905-2841B
End Cap
9905-2842B
9905-2842B
Change Cylinder
9905-2843B
9905-2843B
Main Cylinder
9905-2844B
9905-2844B
Piston
9905-2867XB
9905-2867XB
9905-2846B
9905-2846B
9905-2845B
9905-2845B
Rod Head
9905-2854B
9905-2854B
11
Bushing
9905-2835
9905-2835
12
Guide Plate
9905-2868
9905-2868
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A248
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
19
Bushing
7830-0087
7830-0087
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
22
9905-2869
9905-2869
23
Bonnet Bolts
9905-2834B
9905-2834B
24
O-Ring
7813-3355
7813-A355
25
9905-1242G
9905-1242G
26
9905-0846G
9905-0846G
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
30
9905-2848B
9905-2848B
31
7935-1018G
7935-1018G
32
Indicator Rod
9905-2853B
9905-2853B
33
Seal
7820-0251
7821-0251B
34
Retainer
8007-3038
8007-3038
35
Spacer
9905-2855
9905-2855
61
Pip Seal
7978-1379
7978-1379B
Unit
1396
Rev.
Page 17 of 41
Shear
Actuator
Unit
1396
Rev.
Page 18 of 41
Item No
Part Name
Qty.
H2S -50F
Part No.
Bonnet
9905-2921B
9905-2921B
End Cap
9905-2928B
9905-2928B
Change Cylinder
9905-2932B
9905-2932B
Main Cylinder
9905-2922B
9905-2922B
Piston
9905-2924B
9905-2924B
9905-2929B
9905-2929B
9905-2931B
9905-2931B
11
Bushing
9905-2835
9905-2835
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A2448
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
19
Bushing
7830-0087
7830-0087
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
23
Bonnet Bolt
9905-2937B
9905-2937B
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
35
Guide
9905-2936
9905-2936
36
Secondary Rod
9905-2927B
9905-2927B
37
9905-1487G
9905-1487G
38
Main Rod
9905-2926B
9905-2926B
39
T-Seal
7951-3342
7951-A342
40
T-Seal
7950-3324
7950-A324
41
O-Ring
7813-3241
7813-A241
42
Bushing
7830-0088
7830-0088
43
Retainer
7824-1257
7824-1257
44
SHBS
7943-0402
7943-0402
45
Leaf Spring
9905-2935
9905-2935
46
Slide
9905-2933B
9905-2933B
47
9905-2938
9905-2938
Unit
1396
Rev.
Page 19 of 41
Item No
Part Name
Qty.
H2S -50F
Part No.
48
Outer Piston
2000-5040B
2000-5041B
49
Lock Collar
2000-5041B
2000-5041B
50
Lock Screw
9905-2934B
9905-2934B
60
Guide
2001-0025B
2001-0025B
Shear Seal
Actuator
Unit
1396
Rev.
Page 20 of 41
Item No
Part Name
Qty.
H2S -50F
Part No.
Bonnet
2000-5031B
2000-5031B
End Cap
2000-5032B
2000-5032B
Change Cylinder
2000-5034B
2000-5034B
Main Cylinder
2000-5033B
2000-5033B
Piston, Inner
2000-5039B
2000-5039B
9905-2929B
9905-2929B
9905-2931B
9905-2931B
11
Bushing
9905-2835
9905-2835
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3259
7813-A259
17
T-Seal
7951-3437
7951-A437
18
T-Seal
7951-3220
7951-A220
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
23
Bonnet Bolt
9905-2937B
9905-2937B
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
35
Guide
9905-2936
9905-2936
36
Secondary Rod
2000-5037B
2000-5037B
37
2000-5042G
2000-5042G
38
Main Rod
2000-5038B
2000-5038B
39
O-Ring
7813-3244
7813-3244
40
2000-5043G
2000-5043G
43
Retainer
7824-1257
7824-1257
44
SHBS
7943-0402
7943-0402
45
Leaf Spring
9905-2935
9905-2935
46
Slide
9905-2933B
9905-2933B
47
9905-2938
9905-2938
48
Outer Piston
2000-5040B
2000-5040 B
49
Lock Collar
2000-5041B
2000-5041 B
50
Lock Screw
9905-2934B
9905-2934B
60
Guide
2001-0025B
2001-0025B
Unit
1396
Rev.
Page 21 of 41
Unit
1396
Rev.
Page 22 of 41
Item No
Part Name
Qty.
H2S -50F
Part No.
Bonnet
9905-2841B
9905-2841B
End Cap
9905-2842B
9905-2842B
Change Cylinder
9905-2843B
9905-2843B
Main Cylinder
9905-2844B
9905-2844B
Piston
9905-2421XB
9905-2421XB
9905-2846B
9905-2846B
9905-2845B
9905-2845B
Rod Head
9905-2425B
9905-2425B
10
Handwheel
9905-2851
9905-2851
11
Bushing
9905-2835
9905-2835
12
Guide Plate
9905-2424
9905-2424
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A248
17
T-Seal
7951-3350
7951-A358
18
T-Seal
7951-3220
7951-A220
19
Bushing
7830-0087
7830-0087
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
23
Bonnet Bolts
9905-2834B
9905-2834B
24
O-Ring
7813-3355
7813-A355
25
9905-1242G
9905-1242G
26
9905-0846G
9905-0846G
27
Plug, SAE
7934-0202
7934-0202
28
Nut
7938-0510B
7938-0510B
29
Back-Up Ring
9905-2859
9905-2859
31
7935-1018G
7935-1018G
32
Indicator Rod
9905-2853
9905-2853
33
Seal
7820-0251
7821-0251B
34
Retainer
8007-3038
8007-3038
50
Lock Screw
9905-2832B
9905-2832B
51
Housing
9905-2422B
9905-2422B
Unit
1396
Rev.
Page 23 of 41
Unit
1396
Rev.
Page 24 of 41
Item No
Part Name
Qty
H2 S
Part No.
H2S -50F
Part No.
101
Bonnet
7909-2425
7909-2425B
7909-2425B
102
O-Ring
7813-4918
7813-A918
7813-4918
103
Stem
7909-2426XB
7909-2426XB
7909-2426XB
104
Spacer
7808-1427
7808-1427
7808-1427
105
7817-0371
7817-0371P
7817-0371
106
Seat
7909-2427XB
7909-2427XB
7909-2427XB
109
7940-2501
7940-2501
7940-2501
110*
Spacer
9610-1021
9610-1021
9610-1021
Part Name
EVA6-S000
EVA6-S000B
Qty
H2S -50F
Part No.
102
O-Ring
7813-4918
7813-A918
104
Spacer
7808-1427
7808-1427
105
7817-0371
7817-0371P
109
Allen Wrench
7940-2501
7940-2501
Part Name
EVA6-S001
EVA6-S051B
Qty
H2S -50F
Part No.
102
O-Ring
7813-4918
7813-A918
104
Spacer
7808-1427
7808-1427
105
7817-0371
7817-0371P
109
Allen Wrench
7940-2501
7940-2501
110
Spacer
9610-1021
9610-1021
Unit
1396
Rev.
Page 25 of 41
Unit
1396
Rev.
Page 26 of 41
Part Name
ES46-SK01
ES46-SK01B
Qty.
H2S -50F
Part No.
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A248
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
62
O-Ring
7813-3148
7813-A148
63
7981-0302
7981-0302
Part Name
ES46-SK02
ES46-SK02B
Qty.
H2S -50F
Part No.
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A248
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
33
Seal
7820-0251
7821-0251B
61
Pip Seal
7978-1379
7978-1379B
Unit
1396
Rev.
Page 27 of 41
Part Name
ES46-SK03
ES46-SK03B
Qty.
H2S -50F
Part No.
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A2448
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
39
T-Seal
7951-3342
7951-A342
40
T-Seal
7950-3324
7950-A324
41
O-Ring
7813-3241
7813-A241
43
Retainer
7824-1257
7824-1257
Part Name
ES46-SK04
ES46-SK04B
Qty.
H2S -50F
Part No.
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3248
7813-A248
17
T-Seal
7951-3350
7951-A350
18
T-Seal
7951-3220
7951-A220
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
33
Seal
7820-0251
7821-0251B
34
Retainer
8007-3038
8007-3038
Unit
1396
Rev.
Page 28 of 41
Part Name
ES46-SK05
ES46-SK05B
Qty.
H2S -50F
Part No.
13
O-Ring
7813-3220
7813-A220
14
Seal
7820-1371
7821-1371B
15
O-Ring
7813-3225
7813-A225
16
O-Ring
7813-3259
7813-A259
17
T-Seal
7951-3437
7951-A437
18
T-Seal
7951-3220
7951-A220
20
Seal
7821-1379
7821-1379B
21
Retainer
7826-1756
7826-1756
24
O-Ring
7813-3355
7813-A355
27
Plug, SAE
7934-0202
7934-0202
29
Back-Up Ring
9905-2859
9905-2859
39
O-Ring
7813-3244
7813-A244
43
Retainer
7824-1257
7824-1257
Unit
1396
Rev.
Page 29 of 41
Part Name
601
ES4R-OC41AB
Qty.
Ram Body, RH
9905-1241AB
602
Ram Body, LH
9905-1441AB
603
Multi-Cut Blade
8042-5346
604
SHCS
7935-1006
Shear Ram
Assemblies
Unit
1396
Rev.
Page 30 of 41
ES4ROG35AB
ES4ROG37AB
ES4ROG41AB
ES4ROG44AB
ES4ROG51AB
ES4ROG56AB
ES4ROG61AB
ES4ROG73AB
1.00 Coil
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
2.88 Coil
Qty
9905-0100AB
8041-0143
Slip Ram
Assemblies
ES4ROG35A
ES4ROG37A
ES4ROG41A
ES4ROG44A
ES4ROG51A
ES4ROG56A
ES4ROG61A
ES4ROG73A
1.00 Coil
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
2.88 Coil
Qty
9905-0100AB
8041-0143
Unit
1396
Rev.
Page 31 of 41
1.00
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
501
Ram Body
502
Slip Insert
8440-6735
503
Front Seal
8440-6435D
504
Rear Seal
9905-1901D
505
Retainer Bar
8302-2721
506
O-Ring
507
Compression Pin
9905-2426XB
508
Rocker
8741-0169B
509
Rod Head
9905-2425B
510
Set Screw
7942-0402
511
Ram Guide
2001-0168B
512
Retainer Ring
7824-1007
2.18 Coil
2.38 Coil
2.88 Coil
7813-4210
8440-6737
8440-6741
8440-6744
8440-6751
8440-6756
8440-6761
8440-6773
7813-4210
7813-4210
7813-4210
7813-4210
7813-4210
7813-4210
7813-4210
Unit
1396
Rev.
Page 32 of 41
Qty
ES4RVT35AB
ES4RVT37AB
ES4RVT41AB
ES4RVT44AB
ES4RVT51AB
ES4RVT56AB
ES4RVT61AB
ES4RVT73AB
1.00
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
2.88 Coil
501
Ram Body
502
Slip Insert
8440-6735
503
Front Seal
8440-6635D
504
Rear Seal
9905-1903D
505
Retainer Bar
8302-2721
506
O-Ring
507
Compression Pin
9905-2426XB
508
Rocker
8741-0169B
509
Rod Head
9905-2425B
510
Set Screw
7942-0402
511
Ram Guide
2001-0168B
512
Retainer Ring
7824-1007
7813-A210
8440-6737
8440-6741
8440-6744
8440-6751
8440-6756
8440-6761
8440-6773
7813-A210
7813-A210
7813-A210
7813-A210
7813-A210
7813-A210
7813-A210
Unit
1396
Rev.
Page 33 of 41
Blind Ram
Assembly Number
Pipe Ram
ES4RVP21A
ES4RVP35A
ES4RVP37A
ES4RVP41A
ES4RVP44A
ES4RVP51A
ES4RVP56A
ES4RVP61A
ES4RVP73A
Qty
N/A
1.00 Coil
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
2.88 Coil
99051021AB
99051035AB
99051037AB
99051041AB
99051044AB
99051051AB
99051056AB
99051061AB
99051073AB
7804-2537
8308-2124
8308-2123
Unit
1396
Rev.
Page 34 of 41
Blind Ram
Assembly Number
Pipe Ram
ES4RVP21AB
ES4RVP35AB
ES4RVP37AB
ES4RVP41AB
ES4RVP44AB
ES4RVP51AB
ES4RVP56AB
ES4RVP61AB
ES4RVP73AB
Qty
N/A
1.00 Coil
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
2.88 Coil
99051021AB
99051035AB
99051037AB
99051041AB
99051044AB
99051051AB
99051056AB
99051061AB
99051073AB
7804-2538
8308-2124
8308-2123
Unit
1396
Rev.
Page 35 of 41
Part Name
Qty
ES4RVS35A
ES4RVS37A
ES4RVS41A
ES4RVS44A
ES4RVS51A
ES4RVS56A
ES4RVS61A
1.00 Coil
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
701
Ram Body LH
9905-4251AB
702
Ram Body RH
9905-4151AB
703
Rear Seal
7804-2537
704
Socket Head
Cap Screw
7935-0606
705
Shear Blade LH
706
Shear Blade RH
707
Retainer Bar
8741-0132
Unit
1396
Rev.
Page 36 of 41
Part Name
Qty
ES4RVS35AB
ES4RVS37AB
ES4RVS41AB
ES4RVS44AB
ES4RVS51AB
ES4RVS56AB
ES4RVS61AB
1.00 Coil
1.25 Coil
1.50 Coil
1.75 Coil
2.00 Coil
2.18 Coil
2.38 Coil
701
Ram Body LH
9905-4251AB
702
Ram Body RH
9905-4151AB
703
Rear Seal
7804-2538
704
Socket Head
Cap Screw
7935-0606
705
Shear Blade LH
706
Shear Blade RH
707
Retainer Bar
8741-0132
Unit
1396
Rev.
Page 37 of 41
ES46-T001
Open X Studded
ES46-T001
Open X Studded
Unit
1396
Page 38 of 41
Rev.
Unit
1396
Rev.
Page 39 of 41
Unit
1396
Page 40 of 41
Rev.
Unit
1396
Rev.
Page 41 of 41