Postfach 1166
D -- 24100 Kiel
Germany
Tel +49--4 31--30 19--0
Fax +49--4 31--30 19--501
Email Service@raykiel.com
www.raytheon--anschuetz.de
Digital
Repeater Compass
Type 133 -- 811
SERVICE MANUAL
1 Installation and First Putting into Operation
2 Maintenance, Repair
3 Description, Technical Data
3194E/133--811.DOC032
Edition:
Revision:
CONTENTS
Technical
Documentation
page
1.1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1--1
1.2
1.2.1
1.2.2
1.2.3
2
2.1
2.1.1
2.1.2
2.1.3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3--1
3.1
Annexes
3194E/133--811.DOC032
Left blank
3194E/133--811.DOC032
II
1.1
Installation
Technical
Documentation
Drilling scheme for desk mounting see Dimensional Drawing 133 D 811.HP005 and
133--811.HP015.
Connection of the Digital Repeater Compass to a Gyro compass (for example STD 22):
see cable and connection diagram of the whole equipment.
Connection of the Digital Repeater Compass to any serial NMEA interface:
Pin
e. g. 148--495
4.7 k
5
+24 VDC
+
0
1
3
0V
Pin
RS 232
TX+
TX--
TX--
TX+
DIMMER
DIMMER GND
Input
SERIAL
REMOTE
CONTROL
1
2
3
4
5
6
7
8
9
RS 422
1--1
3194E/133--811.DOC032
1.2
1.2.1
Comments,
Notes
approx. 10s
simultaneously
keep
pressed
or:
3194E/133--811.DOC032
1--2
Indications
Technical
Documentation
Comments,
Notes
1--3
3194E/133--811.DOC032
1.2.2
Indication
Comments,
Notes
e. g.:
approx. 10s
simultaneously
or:
*)
or
-- HEADING SERIAL *)
Note:
On changing to the HEADING
SERIAL*) interface, the digital
repeater compass must be reconfi-gured if it is to serve as steering
repeater compass in a Gyro com-pass equipment
STANDARD 20/22.
(See System Description, Service
Manual)
*)
3194E/133--811.DOC032
1--4
1.2.3
Technical
Documentation
Indication
Comments,
Notes
simultaneously
until --CF-is dispayed
Configuration
Pressing the right button the parameters of the configuration are selected
and
pressing the left button the selected parameter is acknowledged or selected.
The adjusted (acknowledged) parameter flashes in the display.
After approx. 15 seconds without pressing one of the buttons it is automatically switched back to the normal operation mode.
1--5
3194E/133--811.DOC032
Indication
Comments,
Notes
2. Pressing of the right button:
Adjusting the heading source Gyro*.
If the display G-- is flashing, then this
adjustment is active.
If this display does not flash, then it can
be activated by pressing the left button.
* GPS/SAT compass also
3. Pressing of the right button:
Adjusting the heading source Magnetic.
If the display M-- is flashing, then this
adjustment is active.
If this display does not flash, then it can
be activated by pressing the left button.
3194E/133--811.DOC032
1--6
Technical
Documentation
Indication
Comments,
Notes
Switching ON or OFF the LED ring (turn rate and turn direction indicator).
6. Pressing of the right button:
Switching ON or OFF the LED ring.
Flashing rOY (= Rate of Turn Yes) or
rOn (=Rate of Turn no) means this
parameter is active.
With each pressing of the left button it
can be switched (toggle function) between rOY or rOn .
1--7
3194E/133--811.DOC032
Indication
Comments,
Notes
3194E/133--811.DOC032
1--8
Technical
Documentation
Indication
Comments,
Notes
1--9
3194E/133--811.DOC032
Left blank
3194E/133--811.DOC032
1--10
Technical
Documentation
2.1.1
Indications
Possible Cause
Measures
Exchange the cable of the terminals 6 and 7
1
2
3
4
5
6
7
8
9
+
0
flashing
DIMMER
DIMMER GND
SER IN +
SER IN -REMOTE
CONTROL
2.1
2.1.2
Indications
Possible Cause
-- Fault in data storage
-- Phase error
-- Tolerance error
2--1
Measures
-- Fault correction refer to Handbook Magnetic Sonde
3194E/133--811.DOC032
flashing
Possible Cause
--
--
Measures
Change Cable of terminal 6 and 7
DIMMER
DIMMER GND
SER IN +
SER IN -REMOTE
CONTROL
Indications
+
0
2.1.3
1
2
3
4
5
6
7
8
9
flashing
3194E/133--811.DOC032
2--2
Technical
Documentation
Description
The Digital Repeater Compass is designed to indicate the ships heading referred to
north, which has been ascertained by the Gyro/Magnetic compass (GPS/SAT compass
for development status E02 only). The heading is read off at a 7--segment LCD display
(luminous numerals). The numerals are recognizable from up to 10 m, even when
viewed at different angles. The Gyro heading is shown in degrees and decimal degrees.
The decimal digit is made smaller to prevent erroneous reading.
Heading changes are indicated by a tendency indicator. Depending on the speed of the
heading change, a ring consisting of bi--colour LCDs indicate a turn to starboard by
green light and a turn to backboard by red light. The R.o.T. in the LED ring is proportional to the ships R.o.T.
Further characteristics of the Digital Repeater Compass:
-- Recognition of a RS 422 interface acc. to NMEA and therefore automatic change-over of the operation mode when heading serial is detected.
-- Brightness control of all indication elements by keys
-- Synchronisation unnecessary because transmission of absolute values
-- Equipment is ready for assembly in desks and steering stands or
-- for bulkhead, desk and ceiling mounting on a bracket
-- Connection for a central dimmer
-- Connection of a push--button to execute the Freeze function for taking bearings with
a bearing disc
3--1
3194E/133--811.DOC032
3.1
Technical Data
Mechanical Data:
Dimensions:
Weight:
Accuracy of the indication:
0.1 /s
Type of enclosure:
in casing:
Electrical Data:
Voltage supply:
24 VDC (8 to 36 VDC)
Power consumption:
max. 4 W
Input interfaces:
3194E/133--811.DOC032
3--2
Technical
Documentation
NMEA -- Specification:
Transmission mode:
(all information transmitted in acc. to IEC 61162--1; for development status E02
IEC 6112--2 repetiton rate)
3--3
3194E/133--811.DOC032
Left blank
3194E/133--811.DOC032
3--4
Technical
Documentation
Annexes:
Diagrams:
Dimensional Drawings
Annex
3194E/133--811.DOC032
Left blank
3194E/133--811.DOC032
Annex