Mechanical
Anchoring
Product Catalogue
Chemical Anchors
Page 4
Mechanical Anchors
Page 40
Chemical
Anchoring
The Ramset Chemical Anchoring range
consists of Epcon and ChemSet
Injection Adhesives and ChemSet
Maxima glass capsules. Epcon
& ChemSet are Leading Chemical
Anchoring brands in Australia and New
Zealand due to high quality, reliability and
versatility.
The versatile Ramset Chemical Anchor
range provides different options of cost and
performance for anchoring threaded studs,
reinforcing bars and starter
bars into solid and hollow substrates.
Ramset is the specifiers choice, with
easy to use engineering data created
by Ramset engineering professionals
and backed by rigorous testing at the
Ramset Product Engineering Laboratory.
Ramset is part of the world wide ITW
organisation, ensuring youre kept up
to date with the latest technology and
international standards and approvals.
www.ramset.com.au
Contents
Chemical Anchoring
Introduction 4
Selection Guide
8
Injection Adhesives
10
24
26
32
Installation Guide
34
Epcon C8
Reo502 & Reo502EF
Epcon C6EF
Structaset 801
Structaset 401
ChemSet 101 Plus
UltraFix Plus
www.ramset.co.nz
0800RAMSET (726739)
No more dust!
No more hole cleaning!
Safe, secure Chemical Anchoring!
www.ramset.com.au
www.ramset.com.au
www.ramset.co.nz
Chemical Anchoring
Ramset System
Dispensing Solutions
Bonding
Fixing Solutions
Threaded Studs
Overhead Retention
www.ramset.co.nz
0800RAMSET (726739)
Selection Guide
Chemical Anchoring
Pure Epoxy
Epoxy Acrylate
Polyester
Capsule
EPCON C8
EPCON C6EF
Reo 502EF
Reo 502
CHEMSET
801
STRUCTASET
401
CHEMSET
101 PLUS
ULTRAFIX
PLUS
CHEMSET
MAXIMA
M8aM30
M8aM24
M8aM36
M8aM36
M8aM24
M8aM30
M8aM24
M8aM24
M8aM24
8a32
10a32
10a40
10a40
10a24
8a32
10a24
10a24
N/A
Optimum Adhesive
Installation
Temperature (C)
5 a 40
5 a 35
5 a 40
20 a 40
5 a 30
5 a 30
5 a 30
5 a 30
-5 a 35
Working Time
Minutes @ 20C
11min
20min
13min
20min
6min
6min
6min
6min
Loading Time
Hours @ 20C
Dry or Damp
16hrs
3hrs
12hrs
3hrs
50min
50min
50min
50min
20min
Loading Time
Hours @ 20C
Flooded or
Underwater
32hrs
48hrs
85hrs
24hrs
50min
50min
50min
40min
N/A
N/A
Indicative
Load Ranking
(Dry and Damp)
Indicative
Load Ranking
(Flooded &
Underwater)
EPCON
mic loading
Seismic
N/A
EPCON
EPCON
EPCON
EPCON
EPCON
EPCON
EPCON
Dynamic loading
Drilled holes
Fire Rated
SeismicDynamicDrinking
loading water Fire Cracked
Rated concreteSeismic
Drilled holesDrinking water
Cored holes
Cracked concrete
Flooded holesDrilledOversized
holes holesCored holes
Solid Concrete
Flooded holes
safe
safe
Oversized holes
Solid Concret
FireDrinking
Rated water
Dynamic loading
Seismic
Cracked concrete
FireDrinking
RatedDrilled
Dynamic
waterholes
loading
Seismic
CrackedCored
concrete
Fireholes
Drinking
RatedDynamic
Drilled
water
Flooded
holes
loading
Seismic
Cracked
holes Cored
concrete
Fire
Oversized
Rated
holes
Drinking
holes
Drilled
Dynamic
water
Flooded
holes
Seismic
Solid
loading
Cracked
holes
Concrete
concrete
Cored
Oversized
Fire
Drinking
holes
RatedDrilled
holes
water
Dynamic
Flooded
holes
Cracked
loading
Solid
Seismic
holes
Concrete
concrete
Cored
Oversized
Fire
holes
Drinking
Rated
Drilled
holes
Dynamic
water
Flooded
holes loading
Solid
Seismic
Cracked
holes
Concrete
Cored
concrete
Oversized
Fire
holes
Drinking
Ratedholes
Drilled
Dynamic
water
Flooded
holes
Solid
loading
Seismic
holes
Cracked
Concrete
Cored
concrete
Oversized
Fireholes
Drinking
Rated
holes
Drilled
water
Flooded
holes
Solid
Seismic
Cracked
holes
Concrete
Cored
concrete
Oversized
holes
Drinking
holes
Drilled
water
Flooded
holes
Solid
Cracked
holes
Concrete
Cored
concrete
Oversized
holes holes
DrilledFlooded
holes
Solid
holes
Concrete
Cored
Oversized
holes holesFloo
safe
safe
safe
safe
safe
safe
safe
safe
safe
EPCON
EPCON
EPCON
Cored holes
eDrinking
Rated water
Dynamic loading
Seismic
Cracked concrete
FireDrinking
RatedDrilled
Dynamic
waterholes
loading
Seismic
CrackedCored
concrete
Fireholes
Drinking
RatedDynamic
Drilled
water
Flooded
holes
loading
Seismic
Cracked
holes Cored
concrete
Fire
Oversized
Rated
holes
Drinking
holes
Drilled
water
Flooded
holes
Seismic
Solid
Cracked
holes
Concrete
concrete
Cored
Oversized
Drinking
holes
holes
waterFlooded
holes
Cracked
Solid
holes
Concrete
concrete
Cored
Oversized
holes
Drilled
holes
Flooded
holes Solid
holes
Concrete
Cored
Oversized
holes holes
Flooded
Solid
holesConcrete
Oversized
holes Flooded
Solid
Concrete
Dynamic
loading
Fire
RatedDrilled
Seismic
Drinking
water
Cracked
concrete
Drilled
Dynamic
holes
loading
Cored
Fireholes
Rated
Seismic
holes
Oversized
Drinking
holes
water
safe
safe
safe
safe
safe
safe
safe
Flooded holes
Over
Damp
holes
Dynamic
loading
Fireholes
RatedDrilled
Seismic
Drinking
water
Cracked
concrete
Drilled
Dynamic
holes
loading
Cored
Fireholes
Rated Drilled
Flooded
holes Cored
Oversized
Drinking
holes
water
Cracked
Concrete
concrete
DrilledFlooded
holesSolid
Cored
holes holesFlooded
holes
Pull
down
Close
to Seismic
Pullholes
down
ZINC
Close
to Solid
Stainless
Stainless
Seismic
Cracked
ading concrete
FireDrinking
RatedDrilled
Dynamic
waterholes
loading
Seismic
CrackedCored
concrete
Fireholes
Drinking
Rated Drilled
water
Flooded
holesSeismic
Cracked
holes Cored
concrete
Oversized
holes
Drinking
holes
Drilled
water
Flooded
holes
Solid
Cracked
holes
Concrete
concrete
Cored
Oversized
holes
Dynamic
Flooded
holesloading
Solid
holes
Concrete
Cored
Oversized
Fire
holes
Ratedholes
Dynamic
Flooded
loading
Solid
Seismic
holes
Concrete
Oversized
FireDrinking
Ratedholes
water
Solid
Seismic
Cracked
Concrete
concrete
Drinking
water
holes
Cracked
concrete
Drilled
Flooded
holes
holes
Cored
Oversized
holesZINCholes
holes
Concrete
Oversized
Solid
ConcreteOversized holes
Galvanised
Galvanised
feature
feature safe edge
Steel 316
Steel 316
safe
safe
safe
safe
safe
safe edge
Solid
Hole Condition
EPCON
EPCON
EPCON
EPCON
HCR
HCR
HCR
king
edDrilled
Dynamic
waterholes
loading
Seismic
CrackedCored
concrete
Fireholes
Drinking
Rated Drilled
water
Flooded
holesSeismic
Cracked
holes Cored
concrete
Oversized
holes
Drinking
holes
Drilled
water
Flooded
holes
Solid
Cracked
holes
Concrete
concrete
Cored
Oversized
holes Drilled
holes Flooded
holesSolid
holes
Concrete
Cored
Oversized
holes holesFlooded
Solid
holes
ConcreteOversized holes
safe
safe
safe
edge
feature
EPCON
Substrate
EPCON HCR
HCREPCON
HCR
EPCON HCR
HCR
HCR
Brick &
Hollow Wall
EPCON
HCR
Brick &
Hollow Wall
HCR
Brick &
Hollow Wall
HCR
Brick &
Hollow Wall
Brick &
Hollow Wall
Stainless
Pull down
kg
Steel
feature
316
HCR
Brick &
Hollow Wall
Solid Concrete
Close to
edge
ZINC
kg
HCR
Brick &
Hollow Wall
Brick &
Hollow Wall
Hollow
applications
Oversized
holes
Flooded
holesSolid Concrete
Oversized holes
Galvanised
HCR
Dynamic loading
Fire Rated Pull down
Seismic
Drinkingtowater
DrilledZINC
Cored holes
Flooded holes
Oversized holes Close
SolidtoConcrete
Pull down
ZINCStainless
Close
Stainless
nvanised
Close toZINC
Stainless
Pull down
Close toZINC
Stainless
ZINCStainless
Stainless
PullCracked
down concrete
Close
toholesPull down
ZINC
Stainless
kg
kg
kg
kg
Galvanised
Galvanised Close toZINC
Galvanised
Galvanised
Galvanised
Galvanised
Galvanised
kg
kg
safe
feature
edge Steel 316
feature
edge
316
edge Steel
feature
316
edge Steel 316
Steel
316
Steel
feature
316
edge
feature
edge Steel
Steel 316
Damp holes
Damp holes
Damp holes
Damp holes
Damp holes
Damp holes
Damp holes
Damp holes
Brick &
Brick
&
Brick
&
Brick
&
Brick
&
Brick &
Brick &
HCR
HCR
HCR
HCR
HCR
Hollow Wall
Hollow Wall
Hollow Wall
Hollow Wall
Hollow Wall
HCR
Hollow Wall
Hollow Wall
HCR
ZINC
Stainless
Galvanised
Steel 316
HCR
Stainless Galvanised
ZINC
Steel 316 kg
HCR
Brick &
HCR
Hollow Wall
Brick &
HCR
Hollow Wall
Dynamic
loading
Fire Rated
Seismic
Drinking
Cracked
concreteSeismic
Drilled holesDrinking
Cored
holes
Flooded holesDrilled
Oversized
holesCored holes
Solid Concrete
Hollow
applications
mic
Cracked
Seismic
loading
Cored
concrete
holesFire
Drinking
Rated
Drilled
Flooded
water
holes
Dynamic
holes
Cracked
Seismic
loading
Cored
Oversized
concrete
holesFire
Drinking
holes
Rated
Drilled
Flooded
water
Solid
holes
Dynamic
holes
Concrete
Cracked
Seismic
loading
Cored
Oversized
concrete
holesFire
Drinking
holes
Rated
Drilled
Flooded
water
Solid
holesholes
Concrete
Cracked
Seismic
Cored
Oversized
concrete
holesDrinking
holesDrilled
Flooded
water
Solid
holesholes
Concrete
Cracked
Cored
Oversized
concrete
holesholes
Drilled
Flooded
Solid
holes
holes
Concrete
Cored
Oversized
holes
holes
Flooded
Solid water
holes
Concrete
holes
Solid water
Concrete
Dynamic
loading
Fire
RatedOversized
Cracked
concrete
holes
Dynamic
loading
Fire
Rated
Seismic
Drinking
water
Cracked
concrete
Drilled
holes
CoredFlooded
holesholes
Oversized
safe holes
safe
safe
safe
safe
safe
safe
se toZINCPull down
Stainless
Pull down
Pull
Stainless
downGalvanisedClose to ZINCStainless
Pull down
to Stainless
Galvanised Close toZINC
Galvanised Close toZINC
Galvanised CloseZINC
Galvanised
kg
dge
feature kg
edge Steel
feature
316 kg
edge Steel
feature
316 kg
edge
Steel
316kg
feature
edge Steel 316
Brick &
Hollow Wall
Stainless
Steel 316
HCR
Stainless
Steel 316
ON
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
ZINC
Stainless
Pull down
Close toZINC
Stainless
ZINCStainless
Stainless kg
Galvanised
Galvanised
Galvanised
kg
kg
feature
316
edgeholes
Steel 316
Steel 316
Steel 316
esSteel
Damp
Damp
Damp
holes
Hollow
applications
Hollowholes
applications
Hollow
applications
HCR BrickAnchoring
HCR Brick &
HCR Brick &
HCR
&
Environment
Hollow
Wall
Hollow Wall
Hollow Wall
down
alvanised
ure
Dynamic loading
CloseZINC
toStainless
PullGalvanised
down
kg
edgeSteel 316
feature
Hollow applications
Damp holes
rick &
ow Wall
ons
Dynamic loading
Fire Rated
Hollow applications
Damp holes
Brick &
Hollow Wall
Fire Rated
Seismic
kg
kg
feature
Pull down
feature
Drinking water
safe
Close to
edge
Hollow applications
down
HollowPull
applications
tions
Brick &
Hollow Wall
Hollow Wall
Pull down
feature
Damp
holes
Damp holes
Close to
edge
Drinking water
Cracked concrete
Close
toStainless Galvanised
safe ZINC
edgeSteel 316
Hollow applications
Pull down
feature
Hollow
Brick
& applications
Hollow&holes
applications
Brick
Damp
Hollow Wall
Hollow applications
Seismic
CloseZINC
toStainless
PullGalvanised
down
edgeSteel 316
feature
Cracked concrete
HCR
Drilled holes
Cored holes
ZINC
Stainless Galvanised
Steel 316
Flooded holes
Oversized holes
Flooded holes
kg
Hollow applications
Brick &
Hollow Wall
Brick &
Hollow Wall
Oversized holes
Damp holes
Drilled holes
Cored holes
Hollow Wall
kg
ZINC
Damp holes
Galvanised
ZINC
Flooded holes
Brick &
Hollow Wall
Galvanised
Brick &
Hollow Wall
Stainless
Steel 316
Brick &
www.ramset.com.au
Hollow Wall
Galvanised
Oversized holes
Stainless
Steel 316
kg
kg
Hollowholes
applications
Damp
Stainless ZINC
Steel 316
Galvanised
Hollowholes
applications
Damp
Brick &
Hollow Wall
Hollow Wall
loading
Close to Dynamic
edge
Brick &
Damp holes
HCR
kg
Fire
Rated
Hollow
applications
Hollow applications
Damp holes
Stainless
Steel 316
Hollow applications
Hollow applications
Brick
&
Hollow Wall
Seismic
Hollow applications
Drinking water
safe
Hollow applications
Hollow applications
Brick &
Hollow Wall
Solid Concrete
HCR
StainlessHollow applications
Steel 316
Stainless
Steel 316
Damp holes
HCR
Stainless
Steel 316
Hollow applications
HCR
Close to
edge
Hollow applications
HCR
kg
Stainless
Pull down
Steel 316
feature
Hollow applications
Solid Concrete
Hollow applications
Galvanised
Close to
edge
kg
Close to
edge Brick
Hollow&applications
kg
ZINC
Hollow
applications
Damp holes
Pull down
feature
Damp holes
Hollow applications
Damp holes
Cored holes
kg
Hollow applications
Damp holes
kg
Drilled holes
Cracked concrete
Cored holes
kg
HCR
Solid Concrete
Flooded holes
Damp holes
Damp holes
Pull down
Pull down
Pull down
Stainless
Close toZINCPull down
Stainless
Pull down
Pull
Stainless
downGalvanisedClose to ZINCStainless
Pull down
to Stainless
Stainless
Stainless
Galvanised Close toZINC
Galvanised
Galvanised Close toZINC
Galvanised Close toZINC
Galvanised CloseZINC
Galvanised Close toZINC
Galvanised Close toZINC
feature
edge Steelfeature
edge Steel
feature
edge Steel 316
edge Steel
feature
316
edge Steel
feature
316
edge
Steel
feature
316
edge Steel
316
316
316
down
ture
Drilled holes
HCR
kg
HCR
Solid
Cracked
Concrete
concrete
Hollow applications
HCR
Hollow applications
Hollow applications
HCR
Stainless
Steel 316
HCR
Solid Concrete
Selection Guide
Key to Selection Table
Load Ranking indicates load capacity relative to other Ramset Chemical Anchoring adhesives. For load design Refer to Ramset Specifiers Resource Book
Holes drilled with carbide bit and dust removed in accordance with steps 1 to 4 on page 35.
Drilled holes
Holes drilled with diamond core bit dust removed in accordance with steps 1,2 & 3 on page 35.
Cored holes
Water in Holes and not removed or water in holes for greater than 24 hours even if the water is
removed.
Flooded holes
Solid Concrete. All Ramset Chemical Anchoring adhesives are recommended for solid concrete
Solid Concrete
Suitable for installation in hollow clay brick and hollow concrete block in conjunction with perforated
sleeves & sieves. See pages 30 & 37
Hollow applications
Fire Rated
Seismic
Cracked concrete
Certified for load performance in tension zones and other cracked concrete applications.
Refer to Ramset Specifiers Resource Book
www.ramset.co.nz
0800RAMSET (726739)
EPCON C8
CERTIFIED
HIGH PERFORMACE
DESIGN LIFE
Key Features
Injection Adhesives
Pure Epoxy
Seismic Rated (rebar)
Cracked concrete rated
Fire Rated (rebar)
ETAG001-5 option 1
100 years design life
Epcon C8
ETA
ETA
Structaset 401
ETA
Chemset Maxima
VmOpliCant
ETA
Co
ETA 13/0778
ETA
C8 -450
Advantages
High load performance, versatile Pure Epoxy Chemistry
100 year design life in sustained loading
Seismic Design Approved
Cracked concrete and Tension zone approved
Suitable for Flooded Holes, Oversized diameter, Core drilled holes
Easy cold weather dispensing epoxy
Fire Rated for Rebar applications
Certified for contact with Drinking water
Electrical Insulator
Typical Applications
Seismic Upgrade of concrete structures
Tunnel smoke ducts and corbells
Bridge construction and structural upgrades
Road and rail construction
Water infrastructure
Approvals
Certification
ETA 10/0309
ETA 07/0189
26007642/b
DIBt Report
Z-21.8-1866
3/12-727
10
www.ramset.com.au
MAT/LAB 622A
Nr 6010-1845
5 September 2013
EPCON C8
LOAD RANKING*
DRY
Anchoring Environments
FLOODED
Hole
Condition
Dynamic loading
Fire Rated
Seismic
EPCON
Rebar Size Range - 8 to 32
Drinking water
safe
Cracked concrete
Pull down
feature
Drilled holes
Close to
edge
35
30
25
20
15
10
Adhesive
kg
5C to 40C
Galvanised
Operating
Temperature
Range
40
Substrate
5C to 40C
Cored holes
Flooded holes
Oversized holes
Solid Concrete
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Substrates
ZINC
45
Drilled holes
Anchoring
Environment
EPCON EPCON
EPCON
Cored holes
Flooded holes
Oversized holes
50
Installation
Temperature
Range
Cracked concrete
HCR
Solid Concrete
Injection Adhesives
Drinking water
safe
Cored h
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
-40C
50C
HC
5
0
Brick &
Hollow Wall
Pull down
feature
Close to
edge
ZINC
Galvanised
Stainless
Steel 316
HCR
HCR
Damp holes
Stainless
Substrate
GalvanisedTemperature
Steel 316
Working Time
Close
Close
tokg to
Pull down
edgeedge feature
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Hollow applications
5 to 9C
Brick &
Hollow Wall
down
PullPull
down
feature
feature
20 min
30 hours
10 to 19C
14 min
Damp
23holes
hours
20 to 24C
11 min
25 to 29C
8 min
kg
kg
12 hours
30 to 39C
5 min
8 hours
40C
5 min
6 hours
and Underwater
60 hours
kg
BrickBrick
& &
Hollow
Hollow
WallWall
16 hours
Damp
Damp
holesholes
Stainless
Steel 316
Brick &
46
hours
Hollow
Wall
32 hours
24 hours
Damp holes
Hollow applications
16 hours
Hollow
applications
Hollow
applications
12 hours
Hollow applications
Hollow applications
Order Number
C8-450
Related Items
Box Qty
12
Applicator
E108
Mixing Nozzle
ISNE
www.ramset.co.nz
0800RAMSET (726739)
11
ChemSet Reo502
AU
ONLY
Key Features
Injection Adhesives
Pure Epoxy
High bond Strength
Submerged Application
Tolerant of various
hole conditions
Quick 3 hour loading (REO502)
VmOpliCant
Co
NEW
HIGH
PERFORMANCE
CARTRIDGE
ISNE
REO502J600
REO502EF600
Reo 502 is a high performance pure epoxy that provides high load
capacity combined with tolerance to adverse anchoring environments
including core drilled holes, oversized diameters, flooded conditions
and underwater.
One product for all anchoring environments simplifies product
selection.
Reo 502 is available in two versions; Reo 502 EF for easy
dispensing in cold conditions and standard Reo 502 with quick 3
hour setting.
Advantages
High load performance
Versatile Pure Epoxy Chemistry
Suitable for Flooded Holes, Oversized diameter, core drilled holes
and underwater
Quick 3 hour loading time @ 20C (Reo 502)
Easy cold weather dispensing epoxy (Reo 502 EF)
Long working time for deep embedment
Certified for repeated loading for 3 million cycles
Electrical insulator (non-conductive)
Typical Applications
Post - installed reinforcing bar connections for concrete walls,
columns and beams
Structural steel connections
Timber frame tie down per AS1684.2-1999
Starter Bars
Approvals
Certification
3 million Cycles
12
www.ramset.com.au
ChemSet Reo502
LOAD RANKING*
DRY
FLOODED
Anchoring Environments
Hole
Condition
Dynamic loading
Fire Rated
Seismic
EPCON
50
45
40
Substrate
5C to 40C
30
25
Range
15
10
Pull down
feature
5
50
45
40
Installation
Temperature
Range
20C to 40C
Close to
edge
REO502EF
35
30
25
20
15
10
Drilled holes
Cored holes
Flooded holes
Oversized holes
Solid Concrete
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Anchoring
Environment
EPCON EPCON
EPCON
Cored holes
Flooded holes
Oversized holes
Drinking water
Cracked concrete
Drilled holes
Installation
Adhesive
safeTemperature
20
Cracked concrete
Drilled holes
Substrates
REO502
35
Seismic
Drinking water
safe
Adhesive
kg
5C to 40C
Substrate
5C to 30C
ZINC
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
Operating
Temperature
Range
-40C
50C
HC
Pull down
feature
Close to
edge
ZINC
Stainless
Steel 316
Galvanised
HCR
HCR
Damp holes
HCR
Galvanised
Substrate
Temperature
5C
Brick &
Hollow Wall
down
PullPull
down
feature
feature
Reo 502
Stainless
Steel 316
Close
Close
tokg to
Pull down
edgeedge feature
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Reo 502 EF
Brick &
Hollow
TimeWall
to Full Load Capacity
Hollow
Timeapplications
to Full Load Capacity
Working Time
-
Flooded and
Underwater
-
kg
Working
Time
kg
Damp holes
10C
27 min
8 hours
48 hours
23 min
5 hours
32 hours
20C
20 min
3 hours
24 hours
13 min
25C
12 min
2.5 hours
15 hours
30C
8.5 min
2 hours
12 hours
8.5 min
Hollow applications
kg
32 min
15C
Pack Size
600 ml
600 ml
96 hours
22 min
Damp
Damp
holesholes
17 min
Damp holes
Flooded and
Underwater
Brick &
Hollow Wall 240 hours
48 hours
160 hours
22 hours
115 hours
Hollow applications
12 hours
85 hours
Hollow applications
Hollow applications
6 hours
Stainless
Steel 316
Hollow applications
48 hours
Related Items
Box Qty
15
15
Applicator
CUAP/CUAR18
CUAP/CUAR18
Mixing Nozzle
ISNE
ISNE
Cored h
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Galvanised
Brick &
Hollow Wall
HCR
Solid Concrete
Injection Adhesives
www.ramset.co.nz
0800RAMSET (726739)
13
EPCON C6EF
NZ
ONLY
Key Features
Injection Adhesives
Pure Epoxy
High bond Strength
Submerged Application
Tolerant of various
hole conditions
Quick 3 hour loading
ISNE
Co
C6EF-600
Advantages
High load performance
Reliable, strong epoxy bond in adverse conditions
Versatile Pure Epoxy Chemistry
Suitable for Flooded Holes, Oversized diameter, core drilled holes
and underwater
Quick 3 hour loading time @ 20C
Easy cold weather dispensing epoxy
Long working time for deep embedment
14
VmOpliCant
www.ramset.com.au
Typical Applications
Post - installed reinforcing bar connections for concrete walls,
columns and beams
Structural steel connections
Starter Bars
Threaded Studs
EPCON C6EF
LOAD RANKING*
DRY
Anchoring Environments
FLOODED
Hole
Condition
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Cored holes
Flooded holes
Oversized holes
Solid Concrete
Injection Adhesives
Substrates
Seismic
Drinking water
Cracked concrete
Drilled holes
safeThreaded Bar Size Range
50
45
40
EPCON
EPCON
Cored holes
Flooded holes
- M8 to M24
Solid Concrete
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
-40C
Substrate
5C to 30C
25
20
15
10
50C
HCR
35
30
Max
Short Term:
80C
Long Term:
Operating
Temperature
Range
Epcon C6EF
Installation
Adhesive
Temperature
5C to 35C
Range
Pull down
Close to
feature
edge
EPCON
Oversized holes
ZINC
Stainless
Steel 316
Galvanised
HCR
HCR
HCR
down
PullPull
down
feature
feature
kg
ZINC
Stainless
Steel 316
Galvanised
Close
Close
to to
Pull down
edgeedge feature
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Brick &
Hollow Wall
kg
kg
kg
BrickBrick
& &
Hollow
Hollow
WallWall
Damp holes
Brick &
Hollow Wall
Damp
Damp
holesholes
EPCON C6EF
Substrate
Temperature
10C
Brick &
Hollow Wall
Damp holes
Hollow
Timeapplications
to Full Load Capacity
Working Time
Flooded and
Underwater
27 min
8 hours
96 hours
16C
23 min
5 hours
72 hours
Hollow applications
20C
20 min
3 hours
48 hours
27C
12 min
2.5 hours
36 hours
32C
8.5 min
2 hours
24 hours
Stainless
Steel 316
Order Number
C6EF-600
Hollow
applications
Hollow
applications
Hollow applications
Related Items
Box Qty
15
Applicator
CUAP/CUAR18
Mixing Nozzle
ISNE
www.ramset.co.nz
0800RAMSET (726739)
15
ChemSet 801
AU
ONLY
FAST SETTING
HEAVY DUTY
Key Features
Injection Adhesives
Fast Setting
Heavy Duty
Ideal for wall frame tie down
ISNE
C801J
VmOpliCant
Co
C801C
ChemSet 801 is a heavy duty vinyl ester that sets fast for high
productivity.
Fast setting makes ChemSet 801 ideal for applications requiring
fast installation such as hand rails, structural steel, timber frame hold
down, shelf angles etc
Advantages
Heavy duty load performance
Fast setting
Suitable for core drilled holes
Easy cold weather dispensing
Typical Applications
Timber frame tie down per AS1684.2-1999
Corrrosion resistant applications ( water treatment, Industrial)
Fabricated steel (Handrails, Sign posts, Safety rails, Structural
Steel)
Approvals
Certification
AWQC 85026
16
www.ramset.com.au
ChemSet 801
LOAD RANKING*
DRY
Dynamic loading
N/A
Fire Rated
Seismic
Pull down
feature
Close to
edge
Fire Rated
15
10
Adhesive
kg
5C to 30C
Seismic
Galvanised
Operating
Temperature
Range
35
20
Flooded
holes
Damp holes
Oversized holes
Solid Concrete
Drinking water
safe
Substrate
0C to 40C
Cracked concrete
Drilled holes
Cored holes
Flooded holes
Oversized holes
Substrates
ZINC
40
25
Cored holes
Hollow applications
EPCON EPCON
EPCON
Cored holes
Flooded holes
Oversized holes
45
30
Drilled holes
Anchoring
Environment
50
Installation
Temperature
Range
Cracked concrete
Injection Adhesives
Drinking water
safe
S
S
Galvanised
Brick &
Hollow Wall
Hole
Condition
Dynamic loading
Cracked concrete
ZINC
kg
Drinking water
safe
Close to
edge
Anchoring Environments
FLOODED
EPCON
Seismic
Pull down
feature
HCR
Solid Concrete
Solid Co
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
-40C
50C
HCR
Brick &
Hollow
Close toWall
edge
Pull down
feature
ZINC
Galvanised
5C
kg
Working Time
Stainless
Steel 316
Hollow applications
18 min
10C
Brick &
Hollow Wall
down
PullPull
down
feature
feature
Close
Close
to to
Pull Time
down
edgeedge feature
and Damp
20C
25C
5 min
Galvanised
ZINCZINC Galvanised
Close toLoad
to Full
Capacity
edge
kg
kg
BrickBrick
& &
Hollow
Hollow
WallWall
50 minutes
40 minutes
Damp
Damp
holesholes
4 min
35 minutes
Stainless
Steel 316
kg
85 minutes
6 min
Stainless
ZINCStainless
Galvanised
SteelSteel
316316
145 minutes
10 min
Damp holes
30C
Stainless
Steel 316
Galvanised
HCR
HCR
Damp holes
Working and
Loading HCR
Times
Substrate Temperature
ZINC
Brick &
Hollow
- Wall
Damp holes
Hollow applications
Hollow
applications
Hollow
applications
Related Items
Hollow applications
Pack Size
380 ml
750 ml
Order Number
C801C
C801J
Hollow applications
Box Qty
20
12
Applicator
CUAP/CUAR18
CUAP/CUAR18
Mixing Nozzle
ISNE
ISNE
www.ramset.co.nz
0800RAMSET (726739)
17
StructaSet 401
CERTIFIED High Performance
CRACKED CONCRETE
CERTIFIED
Key Features
Injection Adhesives
Structaset 401
ETA
ETA
VmOpliCant
Co
ISNP
S401J
S401C
Advantages
Certified High load performance
50 year design life in sustained load applications
Certified for Cracked Concrete and Tension zones
Suitable for flooded and core drilled holes
Fast setting for high productivity
Easy cold weather dispensing
Certified for contact with drinking water
EPCON
Typical Applications
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drinking water
safe
Cracked concrete
Approvals
Certification
ETA 14/0148
Pull down
feature
Close to
edge
Pull down
feature
Close to
edge
kg
ETA 13/0778
ZINC
Galvanised
ZINC
Galvanised
Brick &
Hollow Wall
kg
Damp holes
Brick &
Hollow Wall
AWQC 77922
Hollow applications
Damp holes
Hollow applications
18
www.ramset.com.au
StructaSet 401
CERTIFIED High Performance
LOAD RANKING*
DRY
Anchoring Environments
FLOODED
Hole
Condition
Dynamic loading
Fire Rated
Drinking water
safe
Cracked concrete
Dynamic loading
Fire Rated
Substrates
Threaded Bar Size Range - M8 to M30
EPCON EPCON
EPCON
Drinking water
safe
Cracked concrete
Pull down
feature
Drilled holes
Cored holes
Flooded holes
Close to
edge
ZINC
45
40
35
30
25
20
15
10
Adhesive
kg
5C to 30C
Oversized holes
Galvanised
Operating
Temperature
Range
50
Installation
Temperature
Range
Cored holes
Flooded holes
Oversized holes
Solid Concrete
Seismic
Dynamic
loading
Drinking
water
Fire Rated
safe
Cracked
concrete
Seismic
Drilled holes
Drinking
water
safe
Cored concrete
holes
Cracked
Anchoring
Environment
EPCON
Seismic
Drilled holes
Injection Adhesives
EPCON
Seismic
Substrate
0C to 40C
Flooded
holes
Drilled holes
HCR
Solid Concrete
Oversized
Cored h
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
-40C
50C
HCR
HC
Brick &
Hollow
Wall
Pull
down
feature
Close to
edge
ZINCto
Close
edge
Pull down
feature
Stainless
ZINC
Galvanised
Steel 316
Galvanised
Stainless
Steel 316
HCR
HCR
Damp holes
Stainless
Substrate
GalvanisedTemperature
Steel 316
Brick &
Hollow Wall
kg
down
PullPull
down
feature
feature
Brick &
Working Time
18 min
10C
10 min
20C
6 min
25C
5 min
30C
4 min
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Brick &
Hollow
Wall
Flooded
DryHollow
andWall
Damp
Hollow applications
5C
Close
Close
tokg to
Pull down
edgeedge feature
145 minutes
kg
kg
BrickBrick
& &
Hollow
Hollow
WallWall
50 minutes
40 minutes
Damp
Damp
holesholes
40 minutes
Damp holes
Hollow applications
35 minutes
Hollow
applications
Hollow
applications
AU
ONLY
Brick
&
85Hollow
minutes
Wall
50 minutes
Hollow applications
35 minutes
and Underwater
145 minutes
kg
Damp
85holes
minutes
Damp holes
Hollow applications
Related Items
Pack Size
380 ml
Order Number
S401C
Box Qty
20
Applicator
CUAP/CUAR18
Mixing Nozzle
ISNP#
750 ml
S401J
12
CUAP/CUAR18
ISNP#
Hollow applications
Stainless
Steel 316
www.ramset.co.nz
0800RAMSET (726739)
19
NO MIXING NO MESS
NO WASTE
ETA
Key Features
Epcon C8
Injection Adhesives
VmOpliCant
ETA
ETA
CERTIFIED Co
HIGH PERFORMACE
Structaset 401
Chemset Maxima
ETA
ETA
ETA 13/0778
DESIGN LIFE
ETA
ISKP
C101C
C101J
ISNP
Not just any polyester; Chemset 101 Plus is formulated using high
performance, Marine Grade Polyester Resin. The European Technical
Approval certification provides peace of mind that Chemset 101 Plus
will deliver what it promises: High Quality, consistent Load Capacity,
even in flooded holes
Advantages
safe
Typical Applications
Fabricated steel (Handrails, Sign posts, Safety rails )
Gates, Fence posts, Rails to hollow brick and Block
Starter bars
Approvals
Pull down
Certification
ETA 13/0681
Close to
edge
ZINC
kg
Brick &
Hollow Wall
Damp holes
20
www.ramset.com.au
Galvanised
S
S
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Cored holes
Flooded holes
Oversized h
LOAD RANKING*
DRY
Anchoring Environments
FLOODED
HCR
Hole
Condition
Pull down
Seismic
Fire Rated
Close to
ZINC
Cored
holes
Drilled
holes
Stainless
Galvanised
Flooded
Cored
holesholes
Oversized
Solid
Concrete
Flooded
holesholes Steel
Oversized
holes
Solid Concrete
316
kg
Anchoring
Environment
EPCON
Brick &
Hollow Wall
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Damp holes
Substrates
Drinking water
safe
Pull down
feature
Cracked concrete
PullClose
downto
edge
feature
Drilled holes
Close to
edge
EPCON EPCON
EPCON
Cored holes
Flooded holes
Oversized holes
ZINC
ZINC
Galvanised
Operating
Temperature
Range
50
45
40
Installation
Temperature
Range
35
30
25
kg
20
15
10
Adhesive
kg
5C to 30C
Stainless
Galvanised
Steel 316
Substrate
0C to 40C
HCR
HCR
Hollow applications
Solid Concrete
Injection Adhesives
Drinking
Crackedwater
concreteCracked
Drilled
holes
Seismic water feature
Drinking
concrete
edge
safe
safe
Cored h
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
-40C
50C
HC
Brick &
Brick &
Hollow Wall Hollow Wall
Damp holes
ZINC
Stainless
GalvanisedTemperature
Substrate
Steel 316
down
PullPull
down
feature
feature
Stainless
Steel 316
5C
18 min
10C
10 min
20C
6 min
25C
Close
Close
tokg to
Pull down
edgeedge feature
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Hollow Wall
kg
kg
145 minutes
BrickBrick
& &
Hollow
Hollow
WallWall
Damp holes
85 minutes
50 minutes
Damp
Damp
holesholes
5 min
40 minutes
4 min
40 minutes
35 minutes
Hollow applications
Related Items
Hollow applications
Order Number
ISKP
C101C
C101J
Brick &
Wall
85Hollow
minutes
Hollow applications
35 minutes
145 minutes
50 minutes
Damp holes
Hollow
applications
Hollow
applications
Pack Size
2 x 380ml Kit
380ml
750ml
Stainless
Steel 316
Time
HollowWorking
applications
Hollow
applications
30C
AU
ONLY
Galvanised
HCR
HCR
HCR
Brick &
Hollow Wall
Close to
edge
Damp holes
Pull down
feature
Box Qty
10
20
12
Applicator
CUAP/CUAR18
CUAP/CUAR18
CUAP/CUAR18
Mixing Nozzle
ISNP#
ISNP#
ISNP#
# NOTE: Mixing nozzle ISNE is also approved for Chemset 101 Plus
For drilling dimensions and full Installation details, refer page 34. In hollow substrate, refer page 37
NOTE: Load Index is the relative load compared with other Chemical Anchoring products in the Ramset range and is intended to assist with product selection. Load Index is not intended to assist with load
design. For load capacity and design information, consult the Ramset Specifiers Resource Book available from Ramset in hard copy or download from the website
www.ramset.co.nz
0800RAMSET (726739)
21
UltraFix Plus
NO MIXING NO MESS
NO WASTE
ETA
Key Features
Epcon C8
VmOpliCant
ETA
Injection Adhesives
CERTIFIED Co
HIGH PERFORMACE
ETA
Structaset 401
Chemset Maxima
ETA
ETA
ETA 13/0778
DESIGN LIFE
ETA
UFP300P
Advantages
Superior Marine Grade Polyester
Suitable for flooded holes
Hollow Brick and Concrete Block
(See page 28 for perforated sleeves)
Solid Concrete
Styrene Free
Fast setting
Easy cold weather dispensing
Typical Applications
Gates, Fences, Rails, plumbing and electrical fixtures to hollow
brickEPCON
and block
Dynamic concrete
loading
Fire Rated
Seismic
Drinking water
Hand rails, Fences, Signposts to solid
safe
Cracked concrete
Dri
Approvals
Pull down
Certification
ETA 13/0681
Close to
edge
ZINC
Galvanised
kg
Brick &
Hollow Wall
Damp holes
Hollow applications
22
www.ramset.com.au
St
Ste
safe
UltraFix Plus
LOAD RANKING*
DRY
Anchoring Environments
FLOODED
HCR
Hole
Condition
Pull down
Close to
ZINC
Cored
holes
Drilled
holes
Stainless
Galvanised
316
Oversized
Solid
Concrete
Flooded
holesholes Steel
Oversized
holes
Solid Concrete
Flooded
Cored
holesholes
kg
EPCON
Anchoring
Environment
Brick &
Hollow Wall
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Damp holes
Drinking water
safe
Pull down
feature
Cracked concrete
PullClose
downto
edge
feature
Drilled holes
Close to
edge
ZINC
ZINC
Galvanised
45
40
Installation
Temperature
Range
35
25
20
kg
15
10
Adhesive
kg
5C to 30C
Stainless
Galvanised
Steel 316
Operating
Temperature
Range
50
30
Substrates
EPCON
EPCON
Cored holes
Flooded holes EPCON
Oversized holes
Substrate
0C to 40C
HCR
HCR
Hollow applications
Solid Concrete
Injection Adhesives
edge
Drinking
Crackedwater
concreteCracked
Drilled
holes
Seismic water feature
Drinking
concrete
safe
safe
Seismic
Fire Rated
Cored h
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
-40C
50C
HC
5
0
Damp holes
Brick &
Brick &
Hollow Wall Hollow Wall
Damp holes
Galvanised
Stainless
Steel 316
Substrate Temperature
Brick &
Hollow Wall
Close to
edge
ZINC
Galvanised
Stainless
Steel 316
HCR
HCR
HCR
down
PullPull
down
feature
feature
ZINC
Pull down
feature
Close
Close
tokg to
Pull down
edgeedge feature
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Stainless
Steel 316
Brick &
Wall
Time to Full LoadHollow
Capacity
Hollow applications
Hollow applications
Working Time
kg
5C
18 min
145holes
minutes
Damp
10C
10 min
85 minutes
20C
6 min
25C
5 min
40 minutes
30C
4 min
35 minutes
50 minutes
Damp
Damp
holesholes
kg
BrickBrick
& &
Hollow
Hollow
WallWall
Brick
&
145
minutes
Hollow Wall
85 minutes
50 minutes
Damp holes
Hollow applications
40 minutes
Hollow
applications
Hollow
applications
35 minutes
Hollow applications
Hollow applications
Order Number
UFP300P
Related Items
Box Qty
12
Applicator
CAGU300
Mixing Nozzle
ISNP
For drilling dimensions and full Installation details, refer page 34. In hollow substrate, refer page 37
*NOTE: Load Index is the relative load compared with other Chemical Anchoring products in the Ramset range and is intended to assist with product selection. Load Index is not intended to assist with load
design. For load capacity and design information, consult the Ramset Specifiers Resource Book available from Ramset in hard copy or download from the website
www.ramset.co.nz
0800RAMSET (726739)
23
ChemSet Maxima
No Mixing, No Waste, No Mistakes
NO MIXING NO MESS
NO WASTE
Epcon C8
Anchoring Capsules
Key Features
ETA
ETA
1 capsule = 1 fixing
Ideal for overhead fixing
No mixing, no mess, no waste
ETAG-001-5 Option 7
Submerged applications
VmOpliCant
ETA
Co
Structaset 401
ETA
ETA
ETA 13/0778
CERTIFIED
HIGH PERFORMACE
ETA
DESIGN LIFE
Maxima glass capsules are the ideal solution for jobs with only a
few fixings where an injection product would be wasted. Maxima
glass capsules non-sag and rapid setting features make them the
best solution for anchoring overhead and in soffit.
The glass breaks during installation and scours the walls of the
borehole to create a strong secure bond in adverse conditions such
as improperly cleaned, core drilled or flooded holes. They can even
be installed underwater.
Maxima capsules are certified for 50 year design life under
sustained loading.
Ideal for structural steel, hand rails, balustrades, cable trays,
mechanical services,
Advantages
The ideal overhead solution
Certified High load performance
One capsule = one fixing = no waste
50 year design life in sustained load applications
Suitable for flooded and core drilled holes
Rapid setting for high productivity
Typical Applications
Fabricated steel connections ( Hand rails, Gates, Fence posts,
Balustrade posts)
Structural Steel connections
EPCON
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Approvals
Certification
Pull down
feature
Close to
edge
ZINC
Galvanised
kg
Brick &
Hollow Wall
Damp holes
24
www.ramset.com.au
Hollow applications
S
S
ChemSet Maxima
No Mixing, No Waste, No Mistakes
LOAD RANKING*
DRY
Anchoring Environments
FLOODED
Hole
Condition
Dynamic loading
Fire Rated
Drinking water
safe
Drinking water
safe
Cracked concrete
Drilled holes
Pull down
feature
Close to
edge
Flooded holes
ZINC
45
40
Installation
Temperature
Range
35
25
20
15
10
Adhesive
kg
-5C to 35C
EPCON
Oversized holes
Galvanised
Operating
Temperature
Range
50
30
Cored holes
Flooded holes
Oversized holes
Solid Concrete
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Substrates
EPCON
EPCON
Cored holes
Drilled holes
Anchoring
Environment
EPCON
Cracked concrete
Substrate
-5C to 35C
HCR
Solid Concrete
Anchoring Capsules
Seismic
Cored h
Dynamic
loading Fire Rated
Fire Rated
Seismic Drinking
Drinking water Cracked
Cracked
concrete Drilled
Drilled holes Cored
Cored holes
Flooded
Dynamic
loading
Seismic
concrete
Dynamic loading
Fire Rated water Seismic
Drinking water holes
Cracked concreteholes Drilled Flooded
holes holes
safe safe
safe
Max
Short Term:
80C
Stainless
Steel 316 Long Term:
-40C
50C
HC
5
0
Brick &
Hollow Wall
Pull down
feature
Close to
edge
ZINC
Galvanised
Stainless
Steel 316
HCR
HCR
Damp holes
Stainless
Substrate
GalvanisedTemperature
Steel 316
Working
Time
Hollow applications
-5 to 0C
Brick &
Hollow Wall
down
PullPull
down
feature
feature
10 to 20C
>20C
Stainless
Galvanised ZINCStainless
Close to ZINCZINC Galvanised
Galvanised
SteelSteel
316316
edge
Hollow
Wall
Flooded
0 to 10C
Close
Close
tokg to
Pull down
edgeedge feature
5 hours
kg
kg
BrickBrick
& &
Hollow
Hollow
WallWall
30 minutes
Damp
Damp
holesholes
20 minutes
and Underwater
10 hours
kg
Damp
60holes
minutes
Stainless
Steel 316
Brick &
120
minutes
Hollow
Wall
60 minutes
40 minutes
Damp holes
Hollow applications
Hollow
applications
Hollow
applications
Order Number
CHEM08
CHEM10
CHEM12
CHEM16
CHEM2024
CHEM2024
Related Items
Box Qty
10
10
10
10
6
6
Applicator
None
None
None
None
None
None
Hollow applications
Mixing Nozzle
None
None
None
None
None
None
For drilling dimensions and full Installation details, refer page 34.
*NOTE: Load Index is the relative load compared with other Chemical Anchoring products in the Ramset range and is intended to assist with product selection. Load Index is not intended to assist with load
design. For load capacity and design information, consult the Ramset Specifiers Resource Book available from Ramset in hard copy or download from the website
www.ramset.co.nz
0800RAMSET (726739)
25
ChemSet Anchor
Key Features
Grade 5.8 Carbon Steel
42um Hot Dip Galvanised
AISI 316 Stainless Steel
Materials
5.8
ZINC
ZINC
ZINC
ZINC
Galvanised
Electroplated Electroplated
Electroplated Electroplated
Stainless
Galvanised
Steel 316
5.8
Carbon
StainlessSteel Carbon Steel
Steel 316
ChemSet Anchor Studs are made from Grade 5.8 carbon steel to
get the most out of adhesive tensile capacities and provide higher
shear capacities than regular Grade 4.6 grade studs. Galvanising of
ChemSet Anchor Studs meets Australian Standards. Stainless Steel
ChemSet Anchor Studs are high corrosion resistant AISI 316 (A4).
External hex drive avoids jamming common with hex bar driven studs.
External hex does not collect rainwater leading to accelerated
corrosion in internal hex drive.
Advantages
High Performance Grade 5.8 Carbon Steel
Hot dip galvanised to AS1650 and AS1214
Hot dip galvanised to 42 micron for exterior applications
High Performance AISI316 Stainless Steel for Coastal Applications
Pre-cut to standard chemical anchoring lengths
Supplied with nuts and washers
Depth set mark to ensure correct embedment
Reliable external hex drive for installing capsules
Ramset Quality
Description
5.8
ZINC
Electroplated
ZINC
ZINC
ZINC
Galvanised
ZINC
Stainless
Galvanised
Electroplated Electroplated
Electroplated Electroplated
Steel 316
5.8
Box
5.8Quantity
Stainless
Carbon Steel Carbon Steel
Galvanised
Carbon
Steel Stainless
Steel 316
Steel 316
M8
CS08110
CS08110GH
CS08110SS
10
M10
CS10130
CS10130GH
CS10130SS
10
M12
CS12160
CS12160GH
CS12160SS
10
M12
CS12180
M16
CS16190
CS16190GH
CS16190SS
10
M20
CS20260
CS20260GH
CS20260SS
M24
CS24300
CS24300GH
CS24300SS
Other sizes and steel types available on request. (Maybe subject to lead time)
10
AU
ONLY
26
www.ramset.com.au
Section
Modulus, Z
(mm3)
31.2
62.3
109.2
109.2
277.5
540.9
935.5
ZINC
troplated
ChemSet Anchor
Key Features
Internal Thread
Flush fitting
Temporary and permanent fixings
Materials
5.8
ZINC
ZINC
ZINC
Stainless
Galvanised
Electroplated Electroplated Electroplated
Steel 316
Carbon Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Advantages
Internally threaded steel inserts are for use with Epcon C8, Epcon
C6EF, ChemSet Reo502 and StructaSet401 adhesives.
Available in zinc plated carbon steel or high corrosion resistant AISI
316 (A4). Ideal for applications where a bolt finish is required.
Typical Properties
500 MPa Carbon Steel
AISI 316 (A4) Stainless Steel
Steel Grades
Threaded Inserts
Drilling Dimensions
Thread
Size
Description
Diameter (mm)
Depth (mm)
5.8 5.8
Box Quantity
M8
Threaded Insert M8 x 60
14
65
062770
062860
10
M10
20
70
062480
062960
10
M12
24
80
062760
063100
10
M16
28
130
062800
051175
10
M20
35
175
062810
10
REO502J600
C8-450
S401J
S401C
C6EF- 600
Typical Properties
Thread Size
M8
M10
M12
M16
M20
60
65
75
125
170
25
32
38
50
63
Carbon Steel
UTS, fu
Tensile Yield
(MPa)
Strength, fy
(MPa)
420
520
420
520
420
520
420
520
420
520
Stainless Steel
UTS, fu
Yield Strength, fy
(MPa
(MPa)
350
350
350
-
650
650
650
-
www.ramset.co.nz
0800RAMSET (726739)
27
ChemSet Anchor
Key Features
Non- destructive
Corrosion resistant
Fast installation
Materials
Nylon
d Concrete
Solid Brick
Substrates
Typical Properties
Property
Overall Length
Nominal Diameter
Material
Service Temperature
Yield Strength Tension ASTM D638
Substrates
Typical Value
220.0 mm
12 mm
Glass Filled Nylon
-5C to 40C
170 MPa
Solid Brick, Solid Concrete
Anchoring Environments
Solid Concrete
Nylon
Nylon
Solid Concrete
Solid Brick
Solid Brick
Advantages
High strength, corrosion resistant glass reinforced nylon
No expansion stress on bricks
Non-destructive installation
Easy, simple and quick to install
Install from either side of the wall
No setting tool required
Fast setting time (in conjunction with ChemSet 101 Plus and Ultrafix Plus)
Recessed for neat finish
Designed to prevent water transfer between cavities
Suitable for installation in damp conditions (with ChemSet 101 Plus and
Ultrafix Plus)
Typical Applications
Description
Part No
Box Quantity
RA225
100
28
www.ramset.com.au
C101J
ISKP
UFP300P
ChemSet Anchor
Nylon Remedial Wall Ties
Installation
3. Insert outer sleeve through first brick into the second until it
reaches the back of the hole
5. Insert the wall tie plunger into the outer sleeve all the way in
6. Adhesive will cure and hold the two brick leaves together
Characteristic Load
0.87 kN
2.05 kN
www.ramset.co.nz
0800RAMSET (726739)
29
ChemSet Anchor
Hollow Brick & Block Sleeves
EPCON
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Cored holes
Key Features
Secure fixing to hollow
substrates, Extruded Clay Brick,
Hollow Concrete Block
Materials
HCR
Pull down
feature
Nylon
Solid Concrete
Close to
edge
ZINC
Solid Brick
kg
Brick &
Hollow Wall
Use with ChemSet 101 Plus and Ultrafix Plus to anchor threaded
studs into hollow brick and block
Anchoring Environments
Damp holes
Forms a solid plug of adhesive in the brick or block cavity to
provide secure anchoring point
Hole
Durable nylon sleeves ideal for 3 hole brick and hollow
EPCON
Conditions
concrete block
Dynamic loading
Rated
Seismic
Drinking water
Cracked concrete
Drilled holes
Coredapplications
holes
Hollow
Fine Metal Mesh Sleeves ideal
for 10 holeFire
brick
safe
For Thread
Size
Typical Applications
Anchoring threaded bar into wire cut extruded clay brick, hollow
concrete block
Pull down
feature
Close to
edge
M6
M8
M10
M12
M16
Substrates
ZINC
Description
Nylon Sleeve 12 mm Diameter
Nylon Sleeve 14 mm Diameter
Nylon Sleeve 16 mm Diameter
Fine Metal Mesh Sleeve12 x 1000 mm
Fine Metal Mesh Sleeve16 x 1000 mm
Fine Metal Mesh Sleeve 22 x 1000 mm
Flooded holes
Oversized holes
Typical Properties
Advantages
Stainless
Steel 316
Galvanised
www.ramset.com.au
Hole
12mm
kg
14mm
16mm
12mm
16mm
22mm
Galvanised
To Suit
M8 Thread
M10 Thread
M12 Thread
Brick &
M8 / M10
Thread
Hollow
Wall
M10 / M12 Thread
M16 Thread
Damp holes
Hollow applications
Nylon Sleeve
Overall
Nominal
Length
Diameter
(mm)
(mm)
64
12
64
14
64
16
HCR
Part Number
ISS08
ISS10
ISS12
ISM10
ISM12
ISM16
Pack Quantity
100
100
100
1
1
1
Solid Concrete
Flooded
ChemSet Anchor
Horizontal & Overhead Accessories
Key Features
Accurate adhesive dose
Ideal for deep holes
Avoids trapped air bubbles
Dosing Cap
The unique Ramset Dosing Cap assists with complete filling of the
hole and avoids trapping air, which can reduce the load capacity of
the bonded fixing.
The unique innovative design allows one part to fit multiple hole
diameters from 15 mm to 40 mm.
Advantages
Installation
Dosing Cap
Description
Dosing Cap
Part Number
050969
Pack Quantity
5
Overhead Retaining
Overhead retaining collars enable threaded studs to remain in place when installed overhead (see page 34.)
Part Number
ISR12
ISR16
Pack Quantity
100
100
www.ramset.co.nz
0800RAMSET (726739)
31
Accessories
Chemical Anchoring
CUAP
CUAR18
Key Features
Key Features
NZ
ONLY
Pack Size
380ml
750ml
380ml
750ml
380ml
750ml
600ml
600ml
600ml
Product
ChemSet 101 Plus
ChemSet 101 Plus
ChemSet 801
ChemSet 801
StructaSet 401
StructaSet 401
ChemSet Reo502
ChemSet Reo502EF
EPCON C6EF
Part Number
C101C, ISKP
C101J
C801C
C801J
S401C
S401J
RE0502J600
RE0502EF600
C6EF-600
E108
Key Features
Robust All Metal design
Dispenses all products in the 450ml Epcong range
Suitable for C8-450 and C6EF-450
32
www.ramset.com.au
Accessories
Chemical Anchoring
Includes:
1 x E108 Applicator
1 x HCBT13 Brush 13mm
1 x HCBT20 Brush 20mm
1 x HCBT26 Brush 26mm
1 x HCPHV Blower
Tough jobsite tool bag
Includes:
1 x CUAP Applicator
1 x HCBT13 Brush 13mm
1 x HCBT20 Brush 20mm
1 x HCBT26 Brush 26mm
1 x HCPHV Blower
Tough jobsite tool bag
Note. Hole cleaning is not necessary with Ramset Dustless Drilling System.
Cleaning dust and debris from holes is necessary to obtain full adhesion and load capacity from Chemical Anchors.
Ramset provides a full range of hole cleaning accessories to ensure the best results from Ramset Chemical Anchoring products
To remove dust and debris after drilling
Removing dust ensures rated load capacities are achieved
Description
Hole Cleaning Pump (High Volume)
Hole Cleaning Brush 13 mm
Hole Cleaning Brush 20 mm
Hole Cleaning Brush 26 mm
Hole Cleaning Brush 20 mm x 1m
Hole Cleaning Brush 26 mm x 1m
Hole Cleaning Brush 36 mm x 1m
Hole Cleaning Brush 42 mm x 1m
To Suit
All hole sizes
8 12 mm Diameter Holes
14 20 mm Diameter Holes
20 24 mm Diameter Holes
14 20 mm Diameter Holes
20 24 mm Diameter Holes
26 34 mm Diameter Holes
36 40 mm Diameter Holes
Part Number
HCPHV
HCBT13
HCBT20
HCBT26
HCBT261000
HCBT201000
HCBT361000
HCBT421000
Pack Quantity
1
1
1
1
1
1
1
1
Always use recommended mixing nozzles for each adhesive. Using the incorrect nozzle will result in improper mixing and poor load resistance.
SO55838
ISNP
Description
AU
ONLY
NZ
ONLY
AU
ONLY
ISNE
SO55837
Compatible With
Part Number
ISNE
10mm
240mm
(425mm extension)
HI Flo Nozzle
S055837
22mm
190mm
Hi Flo Extension
S055838
18mm
400mm
ISNP
10mm
215mm
Description
Compatible With
Part Number
ISNE
10mm
240mm
(425mm extension)
HI Flo Nozzle
C8-450, C6EF-600
S055837
22mm
190mm
Hi Flo Extension
C8-450, C6EF-600
S055838
18mm
400mm
www.ramset.co.nz
0800RAMSET (726739)
33
Installation Instructions
Chemical Anchors Solid Concrete
Installation Guide
Refer to Engineers drawings for specified dimensions. In the absence of Engineer specification, the following dimensions are required.
Refer to Ramset Specifiers Anchoring Resource Book for load design (Available from Ramset or the website www.ramset.com.au)
Bar Size
Minimum Edge
Distance, ec (mm)
Minimum Anchor
Spacing, ac (mm)
Minimum Structural
Thickness, bm (mm)
10
12
16
20
24
28
32
36
40
14
16
20
25
30
35
40
45
50
70
90
120
150
180
210
240
270
300
40
50
65
80
100
115
130
145
160
60
70
100
120
145
170
195
220
240
100
120
160
200
240
280
320
360
400
Table 1. Chemical Anchor Installation Details for Post-Installed Reinforcing Bar in solid Concrete
Installation Details Threaded Bar and ChemSet Anchors Studs in Solid Concrete
Refer to Engineers drawings for specified dimensions. In the absence of Engineer specification, the following dimensions are required.
Refer to Ramset Specifiers Anchoring Resource Book for load design (Available from Ramset or the website www.ramset.com.au)
Thread Size
M8
M10
M12
M16
10
12
14
18
M20
24
M24
26
M30
M36
32
38
Drill Hole
Depth
in Substrate
(mm)
Maximum
Fixture
Clearance
(mm)
Maximum
Fixture
Thickness
(mm)
Tightening
Torque, Tr
(Nm)
Minimum
Edge
Distance,
ec
(mm)
Minimum
Anchor
Spacing,
ac
(mm)
Minimum
Structural
Thickness,
bm
(mm)
80
90
110
125
150
170
160
210
270
330
10
12
15
20
15
25
30
40
10
20
40
95
35
40
50
65
50
60
75
100
24
80
180
80
120
28
105
315
100
145
32
38
650
1150
120
145
180
220
100
120
140
160
190
220
200
270
300
365
Table 2. Chemical Anchor Installation Details for Threaded Bar and ChemSet Anchor Studs in solid Concrete
Tightening
Torque, Tr
(Nm)
Minimum Edge
Distance, ec (mm)
Minimum Anchor
Spacing, ac (mm)
Minimum
Structural
Thickness, bm
(mm)
M8
14
65
10
65
120
100
M10
20
70
22
65
130
100
M12
M16
M20
24
28
35
80
130
175
36
80
120
85
125
170
150
250
340
125
180
240
34
www.ramset.com.au
3
7
45
Installation Instructions
Chemical Anchors Solid Concrete
Installation Details Drilling
Dynamic loading
Fire Rated
Seismic
Drinking water
safe
Cracked concrete
Drilled holes
Cored holes
Flooded holes
Oversized holes
Solid Concrete
Dynamic loading
Pull down
feature
HCPHV
HCR
Drilled holes
Carbide
Drilled
Cored holes
Flooded holes
Oversized holes
Wet/Dry VAC
Solid Concrete
Stainless
Steel 316
mic
micloading
loading
down
down
ure
ature
Compressed Air
Pure Epoxy
x2
x2
x2
x2
x2
HCR
Stainless
Steel 316
Damp holes
Hollow applications
Fire
FireRated
Rated
Seismic
Drinking water
Cracked concrete
Drilled holes
Seismic
Drinking water
Cracked concrete
Drilled holes
Remove dust
and drilling
debris from
Core drilled or
flooded
safe
safe
holes as follows:
Cored
Coredholes
holes
Flooded
Floodedholes
holes
Oversized
Oversizedholes
holes
Solid
SolidConcrete
Concrete
x2
HCR
HCR
Close
Close
toto
edge
edge
ZINC
ZINC
Galvanised
Galvanised
Stainless
Stainless
Steel
Steel316
316
www.ramset.co.nz
0800RAMSET (726739)
35
Installation Instructions
Chemical Anchors Solid Concrete
Opening And Using Cartridge
Installation Guide
1.
Manual CUAP
2.
3.
Pneumatic CUAPN
4.
Manual E108
5.
6.
1. Remove cap from cartridge and attach mixing nozzle. Refer to product
label for correct part number.
2. Load cartridge into dispensing gun (Ramset Part Numbers CUAP (Manual),
E108 (Manual), CUAPN (Pneumatic) and CUAR18 (18V Battery Powered)
3. Dispense a small quantity of adhesive (2 to 3 trigger pulls) to waste to
ensure both adhesive components are balanced.
4. Insert mixing nozzle tip to bottom of hole (to avoid air bubbles) and inject
adhesive. Gradually withdraw nozzle to keep the nozzle tip at the surface
of the adhesive Continue injecting until hole is about filled.
5. Insert fixing using a twisting / rotating motion into adhesive and wipe away
any excess.
6. Allow adhesive to cure. Refer to product label or product pages in this
book or Technical Data Sheets for curing times at various temperatures.
7. Load anchor and apply torque (to threaded fixings) after appropriate cure
time.
Avoid trapping air bubbles. Air bubbles reduce the bonded
area resulting in a lower load capacity
Deep Embedment
4.
1.
For deep holes up to 425 mm, use an extension tube (included with ISNE
mixing nozzles).
For holes deeper than 425mm, use flexible pvc tube with a Ramset Dosing
Cap (Part Number 050969).
1. Break off larger discs from Dosing
Cap to obtain the correct diameter
2. Measure depth of hole.
3. Attach dosing cap to end of
extension tube. Measure and
mark half the hole depth on the
extension tube.
4. Insert extension tube to end of
hole and inject adhesive. Adhesive
in the hole will apply force to the
disc, pushing it back. Stop injecting
when mark on tube appears.
7.
5.
2.
6.
3.
Overhead Installation
Note: Dustless carbide system is recommened to eliminate falling dust and debris during overhead drilling.
Select correct retaining collar from page 31 for M12 and M16 threaded rod. For other threaded rod sizes and rebar, use plastic wedges after the anchor has
been installed.
1. Insert mixing nozzle tip to bottom of hole (to avoid air bubbles) and inject
adhesive. If using retaining collar, place it in the hole and insert nozzle as
illustrated. Gradually withdraw nozzle to keep the nozzle tip at the surface of
the adhesive. Continue injecting until hole is about filled. Dosing Cap (Part
Number 050969) is recommended for deep holes and hole diameters > 18
mm.
2. Insert fixing using a twisting / rotating motion into adhesive and wipe away
any excess. Retaining collar will hold rod in place while adhesive sets. With no
retaining collar, hold fixings in place by inserting 4 x plastic wedges between
the fixing and the concrete.
36
www.ramset.com.au
3. Allow adhesive to cure. Refer to product label or product pages in this book or
Technical Data Sheets for curing times at various temperatures.
4. Load anchor and apply torque (to threaded fixings) after appropriate cure time.
1.
2.
3.
4.
Installation Instructions
Chemical Anchors Hollow Substrates
Read the Precautions section of these instructions prior to use, see page 34.
Setting and technical data provided applies to:
Holes drilled with Rotary Hammers using carbide drill bits and where holes
have been cleaned using a brush and air pump.
Always wear safety goggles.
1. Drill hole using correctly sized drill bit
through wall of hollow block or brick, see
pack or product information.
Correct installation
1.
2.
Installation Guide
Installation Instructions:
Correct installation
8.
4.
10.
www.ramset.co.nz
0800RAMSET (726739)
37
Ramset App
38
www.ramset.com.au
Notes
Chemical Anchoring
Notes
www.ramset.co.nz
0800RAMSET (726739)
39
Mechanical
Anchoring
Ramset have been offering mechanical anchors to
the Australian market for 50 years. During this time,
trusted Ramset brand names, like DynaBolt and
TruBolt, have become so renowned for their quality,
reliability and
performance that their names have entered into
common language on building sites all over Australia.
Unlike any direct competitor, Ramset develops
and manufactures a significant portion of its product
range in Australia for both local and overseas markets.
Ramset also extensively and rigorously tests the
performance of all its anchoring products here in
Australia, in Australian substrates for Australian
applications and conditions to ensure the supply of
accurate information required for anchor design,
selection and safe installation purposes, in Australia.
This Product Guide is designed to provide
information to assist in the selection, ordering
and installation of the appropriate Ramset
mechanical anchor for general anchoring
applications. It has been divided into six
categorised sections - Heavy Duty Anchors,
Medium Duty Anchors, Light Duty Anchors,
Specialised Anchors, Plasterboard & Cavity
Anchors, and Self Drilling Screws - for ease of use.
For more specific or technical information, or for the
purpose of anchor design and strength limit state
calculations, please refer to the Ramset
Specifiers Resource Book.
40
www.ramset.com.au
Contents
Mechanical Anchoring
Anchoring Principles 42
Selection Guide 44
Heavy Duty Anchors 45
SpaTec Plus
Boa Coil
TruBolt
RamPlug
EasyDrive
Nylon Anchors
ShureDrive
Concrete Nails
Specialised Anchors 77
Stainless Steel Trubolt
InsulFast Drill Anchor
Seismic Anchors
www.ramset.co.nz
85
0800RAMSET (726739)
41
Anchoring Principles
Mechanical Anchoring
Types of Substrate
The load capacities, depths, spacings and edge distances published in this
guide are recommended only for the substrates specified in the data tables
for each anchor and are to be used for reference only. Different substrates
may require a different design. Load capacities are also dependent on the
strength of the substrate.
Anchoring Principles
Setting Methods
Torque
Torque Setting Anchors, also known as Torque Controlled Anchors, require
the application of a recommended or controlled assembly torque, or twisting force, to the nut or bolt head to be correctly set and achieve published
loads. This is applied and measured with a torque wrench and is checkable
after installation.
Rotation
Rotation Setting Anchors are set by rotation. These anchors will achieve
published loads when tight without the need for the application of a
controlled torque.
Should your anchoring scenario vary from the basis of the published data,
please consult the Ramset Specifiers Resource Book or qualified engineer
for more information.
Load Directions
Load capacities published in this guide refer to Tensile and Shear. These load
directions are defined below.
Tensile (0 a 10)
Displacement
Displacement Setting Anchors, are set by driving a captive expander
component into the bottom end of the anchor, usually with hammer blows, to
a controlled depth that is checkable after anchor installation.
Impact
Impact Setting Anchors are set with hammer blows. They can either be a
single element or an anchor with an expander component. The difference
between Impact Setting Anchors and Displacement Setting Anchors is that
Impact Setting Anchors do not require a controlled measure to achieve a set.
Load Assisted
Load Assisted Anchors are set by the application of a tension load. They also
do not require a controlled measure to achieve a set. This type of anchor is
usually only used as a suspension anchor.
Anchoring Methods
Expansion
Expansion Anchors are generally installed in a pre-drilled hole with a
diameter slightly larger than the outer diameter of the anchor. The anchors
diameter is then expanded at the bottom end utilising the appropriate setting
method. This expansion creates a high friction force between the base of
the anchor and the wall of the hole. The surrounding substrate contains and
restricts the expansion forces and holds the anchor in place.
If your required load angle is more complex, i.e. a combination of tensile and
shear loads, please consult the Ramset Specifiers Resource Book or
qualified engineer for more information.
Load Classification
Static Load
An applied load is static when it changes very little over time.
Thread Forming
Thread Forming Anchors tap their own thread in a pre-drilled hole that is
slightly smaller than the outer diameter of the anchor, creating a mechanical
interlock between the anchor and the substrate. This method of anchoring
does not apply expansive forces or burst the substrate, making it suitable for
close-to-edge or close-to-anchor applications.
Vibrating Load
A variable cyclic load of relatively low amplitude and high frequency e.g.
motor or fan vibration.
Interference Fit
Interference or Friction Fit Anchors achieve anchorage by applying a friction
force between the anchor and the wall of the hole along the anchors length.
The surrounding substrate contains the forces and holds the anchor in place.
This anchoring method is usually reserved for light duty applications.
Shock Load
An isolated high load applied in a very short period of time.
Deformation
Deformation Anchors are used for cavity fixing. Anchorage is achieved by
changing the shape of the anchor on the inside of the cavity and clamping
the anchor body up against the substrate via the appropriate setting method.
42
www.ramset.com.au
Dynamic Load
An irregular variable load of relatively medium or high amplitude e.g. wind.
Anchoring Principles
Mechanical Anchoring
Anchor Spacing
Taking into account the stress values created by mechanical anchors and the loads they are designed to support, the following points must be considered
when establishing the performance of each individual product (recommended load):
Anchoring Principles
www.ramset.co.nz
0800RAMSET (726739)
43
Selection Guide
4 4 4 4 4 4 4
4 4 4 4 4 4 4
Nylon Anchors
4 4 4 4
4 4 4 4 4 4 4
Concrete Nails
4 4
4 4 4 4
4 4
4 4 4
44
www.ramset.com.au
Cement Sheet
Timber
4 4 4 4 4 4
Particleboard
Hollow Brick
Aerated Concrete
Hollow Slab
Plasterboard
4 4 4 4 4 4
Hollow Block
Solid Brick
Solid Block
Solid Stone
Mechanical Anchor
Concrete
Selection Guide
Mechanical Anchoring
Heavy Duty
Mechanical Anchoring
www.ramset.co.nz
0800RAMSET (726739)
45
SpaTec Plus
Safety Anchors
ZINC
ectroplated
Materials
5.8
ZINC
Galvanised
Electroplated
Stainless
ZINC
Electroplated
Steel 316
Carbon
Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Description
The SpaTec Plus Safety Anchor is a heavy duty, torque controlled expansion
anchor, with an integrated pull-down section, designed for high performance
in both static and dynamic load applications, in both cracked and
non-cracked concrete~. The SpaTec Plus is ideally suited for through fixing
into concrete when security and reliability are paramount.
~
Whether a concrete element is classified as cracked or non-cracked is to be determined
by a qualified structural engineer.
Specification
Material - Bolt
Class 8.8 High Tensile Carbon Steel
( 316 (A4) Stainless Steel available to order )
Corrosion Protection
Zinc Plating
Head Styles
Hex or Countersunk. (SP16145ESS-Hex Nut)
Fixing Method
Through Fixture
Setting Method
Torque Controlled
Anchoring Method Expansion
Thread Diameters
M10, M12, M16, M20
Drilled Hole Diameters
15mm,18mm, 24mm, 28mm
Anchor Lengths
105mm, 110mm, 120mm, 130mm,
145mm, 170mm
Maximum Fixture Thickness 10mm, 20mm, 25mm, 27mm, 40mm
Indicative Working
Max Tensile 16.7kN - 46.0kN
Loads in 32MPa Concrete* Max Shear 19.3kN - 75.8kN
Substrates Concrete
* Refer to load table
Related Products
DynaDrill
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
46
www.ramset.com.au
The combination of a high tensile class 8.8 bolt with an extra thick-walled
spacer allows a smaller diameter bolt to be used for easier installation
while still providing both excellent tensile and shear performance. The
spacer also incorporates a visual maximum fixture thickness indicator for
ease of use.
The patented anti-rotation expansion sleeve is designed with sharp angled
protrusions that grip the sides of the hole, preventing anchor rotation
during installation. As expansion of the sleeve begins, the locking barbs
also grip the sides of the hole, further embedding as expansion
progresses, giving extra holding power. The sleeve pulls down during
tightening ensuring excellent pressure between the fixture and the
concrete.
The low profile hex or countersunk heads provide a neat finish.
SpaTec Plus
Safety Anchors
Steel Maintenance Plumbing Electrical
Construction Elevator
Fabricator
Fitter
Contractor
Contractor
Contractor Installer
Anchoring structural steel columns/beams
4
Anchoring HVAC units
4
4
Machinery hold down
4
Anchoring crane rails
4
Anchoring Elevator Guide Rails
4
1. Drill or core a hole to the recommended diameter and depth using the
fixture as a template. Clean the hole thoroughly with a hole cleaning brush.
Remove the debris with a hand pump, compressed air, or vacuum.
2. After ensuring that the anchor is assembled correctly, insert the anchor
through the fixture and drive with a hammer until the washer contacts
the fixture.
3. Tighten the bolt with a torque wrench to the specified assembly torque.
SP06065
NZ
ONLY SP06080
Thread
Size
Max Fixture
Thickness (mm)
Overall Anchor
Length (mm)
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Drilled Hole
(mm)
Stainless
Steel 316
Carbon Steel
Fixture Hole
(mm)
Min Hole
Depth (mm)
Effective
Length (mm)
Order
Qty
M6
5
65
10
12
M6
20
80
10
12
SP08065 M8
1
65
12
14
SP08090 M8
20
90
12
14
SP12NUT M12
SP10075 M10
1
75
15
17
70
70
80
80
105
90
55 100
70 100
61 100
80 50
SP10105
SP12105
SP12120
SP16145
SP20170
90
105
105
131
157
90
90
105
125
150
M10
M12
M12
M16
M20
20
10
25
25
25
105
105
120
145
170
15
18
18
24
28
17
20
20
26
31
NZ
Overall Anchor
Length (mm)
95
105
130
71 25
25
25
25
10
5
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Installation
Carbon Steel
Drilled Hole
Fixture Hole
Min Hole
Effective
Order
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
12
14
80
86 50
15
17
90
97
25
18
20
90
120
10
Available to order.
Lead times apply.
SpaTec Plus Safety Anchors - Hex Bolt - Stainless Steel Grade AISI 316 (A4)
Part No
SP10105SS
SP12120SS
SP16145ESS*
Thread
Size
M10
M12
M16
Max Fixture
Thickness (mm)
25
25
25
Overall Anchor
Length (mm)
115
120
157
Drilled Hole
(mm)
15
18
24
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Fixture Hole
(mm)
17
20
26
5.8
Stainless
Steel 316
Carbon Steel
Min Hole
Depth (mm)
90
105
130
Effective
Length (mm)
95
105
120
Order
Qty
25
25
10
Embedment
Depth (mm)
80
95
115
140
Tightening
Torque (Nm)
50
80
120
200
Min Edge
Distance (mm)
120
145
175
210
Min Anchor
Spacing (mm)
240
285
345
420
Max Tensile
Load, Na (kN)*
16.7
22.6
32.4
46.0
Max Shear
Load, Va (kN)*
19.3
27.6
52.3
75.8
*The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset Specifiers Resource Book for more information or explanation of technical data.
www.ramset.co.nz
0800RAMSET (726739)
47
Boa Coil
Expansion Anchors
Materials
Expansion coil
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Description
The Boa Coil Expansion Anchor is a removable, high strength, heavy duty,
rotation setting expansion anchor for concrete. The Boa is ideally suited for
though fixing into concrete when cast-in performance or clean removal is
required.
Specification
Material - Bolt
Carbon Steel
Corrosion Protection
Zinc Plating
Head Styles Hex
Fixing Method
Through Fixture
Setting Method Rotation
Anchoring Method Expansion
Drilled Hole Diameters
13mm, 16mm, 19mm
Anchor Lengths
75mm, 90mm, 100mm, 115mm, 125mm
Maximum Fixture Thickness 12mm, 25mm,30mm, 40mm
Indicative Working
Max Tensile 12.6kN - 19.6kN
Loads in 32MPa Concrete* Max Shear 15.4kN - 28.4kN
Substrates Concrete
* Refer to load table
Related Products
DynaDrill
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
Hole Cleaning Brush
48
www.ramset.com.au
High load capacity is achieved due to the expansion coil locking into the
sides of the hole, when set, to give cast-in type performance.
High clamping load and resistance to cyclic loading result from the pull-
down effect achieved through the rotation setting action of the anchor.
Low profile hex head provides a neat finish.
Removal is easy, clean and fast, as the expansion coil stays in the hole
leaving no protruding metal parts to grind off. The bolt can even be re-
used with a new coil.
Boa Coil
Expansion Anchors
Steel
Concrete
Scaffold Maintenance
Fabricator
Formworker
Contractor
Fitter
Installing handrails, balustrades & safety barriers
4
Formwork support
4
Scaffold support
4
Anchoring structural steel columns/beams
4
Machinery hold down
4
Installation
1. Drill or core a hole to the recommended diameter and depth using the fixture
as a template. Clean the hole thoroughly with a hole cleaning brush.
Remove the debris with a hand pump, compressed air, or vacuum.
2. After ensuring that the anchor is assembled correctly (the coil tab points up
the anchor), insert the anchor through the fixture. Tap the anchor down to
the depth set mark, with a hammer, and stop.
3. Wind the anchor down, with an appropriately sized spanner or socket
wrench, until the washer is firmly held to the fixture and stop (5 turns).
Ensure washer is tight and snug fit.
4. The Boa Coil anchor is ready to take load. (The bolt can be removed
leaving the coil in the hole. To re-insert, follow steps 3 and 4.)
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No
Anchor
Max Fixture
Overall Anchor
Drilled Hole
Fixture Hole
Min Hole
Effective Order
Size (mm) Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm) Length (mm) Qty
BAC08075
13
12
75
13
14
90
59
50
BAC08100
13 30 100 13 14 100
84
50
BAC10090
16 12 90 16 19 105
71
25
BAC10125
16 40 125 16 19 130
106
25
BAC12115
19 25 115 19 21 120
93
20
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Coil Only
Order
Part No
Qty
BAC08 100
BAC10 50
BAC12 50
Embedment
Depth (mm)
75
90
80
Torque
(turns to set)
5 turns
5 turns
5 turns
Min Edge
Distance (mm)
80
100
120
Min Anchor
Spacing (mm)
160
200
230
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Max Tensile
Load, Na (kN)*
12.6
18.6
19.6
Max Shear
Load, Va (kN)*
15.4
26.0
28.4
*The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset Specifiers Resource Book for more information or explanation of technical data.
www.ramset.co.nz
0800RAMSET (726739)
49
TruBolt
Stud Anchors
ZINC
Electroplated
Anchor diameter
equals Hole diameter
Materials
Anti-rotation expansion sleeve
5.8
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Description
Specification
Material - Bolt
Carbon Steel, Stainless Steel 316 (A4)
Corrosion Protection
Zinc Plating, Hot Dipped Galvanising
Head Styles
Hex Nut
Fixing Method
Through Fixture
Setting Method
Torque Controlled
Anchoring Method Expansion
Thread Diameters
M6, M8, M10, M12, M16, M20
Drilled Hole Diameters
6mm, 8mm, 10mm, 12mm, 16mm, 20mm
Anchor Lengths
55mm, 65mm, 75mm, 80mm, 85mm,
90mm, 100mm, 120mm, 125mm, 140mm,
150mm, 160mm, 175mm, 180mm, 215mm
Maximum Fixture Thickness 6mm, 8mm, 10mm, 12mm, 15mm, 20mm,
25mm, 30mm, 35mm, 40mm, 45mm,
50mm, 65mm, 70mm, 80mm, 90mm,
100mm
Indicative Working
Max Tensile 3.4kN - 32.5kN
Loads in 32MPa Concrete* Max Shear 2.8kN - 27.3kN
Substrates Concrete
* Refer to load table
Related Products
DynaDrill
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
Hole Cleaning Brush
50
www.ramset.com.au
TruBolt
Stud Anchors
Installation
1. Drill or core a hole to the recommended diameter (same as the TruBolt)
and depth using the fixture as a template. Clean the hole thoroughly with
a hole cleaning brush. Remove the debris with a hand pump, compressed
air, or vacuum.
2. Insert the anchor through the fixture and drive with a hammer until the
washer contacts the fixture.
3. Tighten the nut with a torque wrench to the specified assembly torque.
Ramset
Part No
Description
Thread
Diameter
ZINC
Electroplated
Galvanised
Carbon Steel
Total
anchor
length
Drill
Diameter
Hole depth
minus fixture
thickness
Minimum
Drilling depth
Maximum
fixture
thickness
Maximum
tightening
Torque
Fixture
clearance
hole diameter
T06055SSA
Trubolt M6 x 55mm
55mm
66mm
51mm
15mm
10Nm
T08055SSA
Trubolt M8 x 55mm
55mm
70mm
65mm
5mm
20Nm
T08070SSA
Trubolt M8 x 70mm
70mm
85mm
65mm
20mm
20Nm
T08090SSA
Trubolt M8 x 90mm
90mm
105mm
65mm
40mm
20Nm
T08130SSA
Trubolt M8 x 130mm
130mm
145mm
65mm
80mm
20Nm
T10065SSA
10
10
65mm
83mm
78mm
5mm
35Nm
12
T10075SSA
10
10
75mm
93mm
78mm
15mm
35Nm
12
T10095SSA
10
10
95mm
113mm
78mm
35mm
35Nm
12
T10120SSA
10
10
120mm
138mm
78mm
60mm
35Nm
12
T12080SSA
12
12
80mm
100mm
95mm
5mm
50Nm
14
T12100SSA
12
12
100mm
120mm
95mm
25mm
50Nm
14
T12115SSA
12
12
115mm
135mm
95mm
40mm
50Nm
14
T12140SSA
12
12
140mm
160mm
95mm
65mm
50Nm
14
T16125SSA
16
16
125mm
147mm
117mm
30mm
100Nm
18
T16150SSA
16
16
150mm
172mm
117mm
55mm
100Nm
18
T16170SSA
16
16
170mm
192mm
117mm
75mm
100Nm
18
Part No
Thread
Size
Max Fixture
Thickness (mm)
T20140SS M20
T20160SS
M20
5.8
Stainless
Steel 316
10
35
ZINC
Electroplated
Galvanised
5.8
Stainless
Steel 316
Overall Anchor
Length (mm)
120
160
Carbon Steel
Drilled Hole
(mm)
20
20
Fixture Hole
(mm)
24
24
www.ramset.co.nz
Min Hole
Depth (mm)
Effective
Length
Order
Qty
140 85 10
170
115
10
0800RAMSET (726739)
51
TruBolt
Stud Anchors
ZINC
Electroplated
5.8
Galvanised
Stainless
Steel 316
Carbon Steel
Part No
Thread
Max Fixture
Overall Anchor
Drilled Hole
Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length
Qty
T12080GH M12
6
80
12
15
90 58 20
T12100GH M12
25
100
12
15
105 71 20
T12120GH
NZ
ONLY
M12
T12140GH M12
T12180GH M12
T16110GH M16
T16125GH M16
T16150GH M16
T16175GH M16
T20140GH M20
T20160GH
M20
T20215GH M20
45
120
12
15
105
93
65
100
8
20
45
70
10
35
90
140
180
100
125
150
175
120
160
215
12
12
16
16
16
16
20
20
20
15
15
19
19
19
19
24
24
24
105
125
115
135
145
145
140
170
200
111 20
151 20
67 20
85 20
110 20
135 20
85 10
115
10
170 10
AU
ONLY
ZINC
Electroplated
20
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No
Thread
Max Fixture
Overall Anchor
Drilled Hole
Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length
Qty
T06055
M6
15
55
6
8
55
38
100
T06085 M6
45
85
6
8
75
68 100
T06120 M6
80
120
6
8
75
103 50
T06150 M6
110
150
6
8
75
133 100
T06180
M6
140
180
6
8
75
163
100
T08065
M8 12
65 8 10 65 45
50
T08090
M8 40
90 8 10 75 70
50
T10075
M10 12
75 10 12 80 52
50
T10090
M10 30
90 10 12 90 67
50
T10120
M10 50
120 10 12 100 97
20
T12080
M12 6
80 12 15 90 58
20
T12100
M12 25
100 12 15 105 71
20
T12120
M12 45
120 12 15 105 93
20
T12140 M12
65
140
12
15
105
111 20
T12180 M12 100
180
12
15
125
151 20
T16110
M16 8
110 16 19 125 67
20
T16125
M16 20
125 16 19 135 85
20
T16150 M16
45
150
16
19
145
110 20
T16175 M16
70
175
16
19
145
135 20
T20140
M20 10
140 20 24 160 85
10
T20160
M20
35
160
20
24
170
115
10
T20215 M20
90
215
20
24
200
170 10
52
www.ramset.com.au
Medium Duty
Mechanical Anchoring
www.ramset.co.nz
0800RAMSET (726739)
53
WERCS AnkaScrew
Screw-In Anchors
ZINC
Electroplated
Hardened, ductile
carbon
steel construction
NEERWCS
Materials
5.8
ZINC
Electroplated
Galvanised
Stainless
Steel 316
W EAD
THR
Patented WERCS sawtooth thread
design provides clearance for rapid
removal of material
Reduces jamming
Reduces installation torque by around 50%
Increases ease of installation
Carbon Steel
Description
Specification
Material
Carbon Steel
Corrosion Protection
Zinc Plating, Mechanical Galvanising
Head Style
Flanged Hex (5mm & 6mm),
Hex (8mm, 10mm & 12mm)
Fixing Method
Through Fixture
Setting Method
Rotation
Anchoring Method
Thread Forming
Drilled Hole Diameters
5mm, 6mm, 8mm, 10mm, 12mm
Anchor Lengths
30mm, 50mm, 60mm, 75mm,
100mm, 120mm, 150mm
Maximum Fixture Thickness 5mm, 10mm, 15mm, 20mm, 25mm,
35mm, 40mm, 45mm, 50mm, 60mm,
70mm, 90mm, 100mm
Indicative Working
Max Tensile 1.4kN -14.4kN
Loads in 32MPa Concrete* Max Shear 1.5kN - 16.7kN
Substrates
Concrete, Solid Brick, Solid Block,
Hollow Block, Hollow Slab, Hollow Brick
* Refer to load table
54
www.ramset.com.au
Related Products
DynaDrill
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
Hole Cleaning Brush
WERCS AnkaScrew
Screw-In Anchors
Concrete Formworker
Installation
1. Drill or core a hole to the recommended diameter and depth using the fixture
as a template. Clean the hole thoroughly with a hole cleaning brush. Remove
the debris with a hand pump, compressed air, or vacuum.
2. Insert the AnkaScrew through the fixture and screw it into the hole with
either a socket wrench or an impact wrench (with an impact socket) using
slight pressure until the self-tapping action begins.
3. Tighten the AnkaScrew until the fixture is held firm. If resistance is
experienced when tightening, unscrew the anchor one turn and re-tighten.
Ensure that you do not over tighten.
Part No
Finish
Anchor
Size
(mm)
SHW4 -134
NZ
ONLY
SPF4 -334
410SS
410SS
5mm
5mm
AS06050WGM100
AS06075WGM100
AS06100WGM100
AS08060WGM100
AS08075WGM100
AS08100WGM100
AS10060WGM50
AS10075WGM50
AS10100WGM50
AS10150GH
ONLY AS12075WGM50
AS12100WGM50
AS12150WGM20
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
GALVANISED
6mm
6mm
6mm
8mm
8mm
8mm
10mm
10mm
10mm
10mm
12mm
12mm
12mm
NZ
Maximum
Fixture
Thickness
(mm)
AS06100W100
AS08060W100
AS08075W100
AS08100W100
AS10060W50
AS10075W50
AS10100W50
AS12075W50
AS12100W50
AS12150W20
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
ZINC
6mm
6mm
6mm
8mm
8mm
8mm
10mm
10mm
10mm
12mm
12mm
12mm
5.8
Galvanised
Stainless
Steel 316
Carbon Steel
Drill
Diameter
(mm)
Fixture Hole
Diameter
(mm)
Min Hole
Depth
(mm)
Socket
Size
(mm)
Qty
19mm
69mm
45mm
95mm
5mm
5mm
7mm
7mm
8mm
8mm
100
100
20 mm
45 mm
70 mm
20 mm
35 mm
60 mm
10 mm
25 mm
50 mm
100 mm
15 mm
40 mm
90 mm
50mm
75mm
100mm
60mm
75mm
100mm
60mm
75mm
100mm
150mm
75mm
100mm
150mm
6 mm
6 mm
6 mm
8 mm
8 mm
8 mm
10 mm
10 mm
10 mm
10 mm
12 mm
12 mm
12 mm
8 mm
8 mm
8 mm
10 mm
10 mm
10 mm
13 mm
13 mm
13 mm
13 mm
15 mm
15 mm
15 mm
10 mm
10 mm
10 mm
13 mm
13 mm
13 mm
15 mm
15 mm
15 mm
14 mm
16 mm
16 mm
16 mm
100
100
100
100
100
100
50
50
50
25
50
50
20
10 mm
10 mm
10 mm
13 mm
13 mm
13 mm
15 mm
15 mm
15 mm
16 mm
16 mm
16 mm
100
100
100
100
100
100
50
50
50
50
50
20
AS06050W100
AU
ONLY AS06075W100
ZINC
Electroplated
Overall
Anchor
Length
(mm)
20 mm
45 mm
70 mm
20 mm
35 mm
60 mm
10 mm
25 mm
50 mm
15 mm
40 mm
90 mm
5.8
ZINC
Electroplated
50mm
75mm
100mm
60mm
75mm
100mm
60mm
75mm
100mm
75mm
100mm
150mm
ZINC
Electroplated
Galvanised
Stainless
Steel 316
6 mm
6 mm
6 mm
8 mm
8 mm
8 mm
10 mm
10 mm
10 mm
12 mm
12 mm
12 mm
Carbon Steel
8 mm
8 mm
8 mm
10 mm
10 mm
10 mm
13 mm
13 mm
13 mm
15 mm
15 mm
15 mm
Embedment
Min Edge
Min Anchor
Hole (mm)
Depth (mm)
Distance (mm)
Spacing (mm)
45
60
75
90
60
80
100
120
35
45
60
70
6
8
10
12
Max Tensile
Load, Na (kN)*
4.1
6.6
9.8
14.4
Max Shear
Load, Va (kN)*
4.5
8.4
13.8
16.7
*The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset Specifiers Resource Book for more information or explanation of technical data.
www.ramset.co.nz
0800RAMSET (726739)
55
DynaBolt Plus
Sleeve Anchors
ZINC
Electroplated
Materials
5.8
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Description
Specification
Material
Carbon Steel, Stainless Steel 316 (A4)
Corrosion Protection
Zinc Plating, Hot Dipped Galvanising
Head Style
Hex Nut, Hex Bolt, Countersunk/Flat Head,
Round Head, Hook, Eye, Tie Wire
Fixing Method
Through Fixture
Setting Method
Torque Controlled
Anchoring Method
Expansion
Thread Sizes
M4.5, M6, M8, M10, M12, M16
Drilled Hole Diameters
6mm, 8mm, 10mm, 12mm, 16mm, 20mm
Anchor Lengths
26mm, 34mm, 38mm, 40mm, 41mm
45mm, 49mm, 55mm, 57mm,
60mm, 62mm, 65mm, 66mm, 70mm,
75mm, 76mm, 80mm, 81mm, 85mm,
92mm, 98mm, 100mm, 103mm,
106mm, 113mm, 126mm, 140mm, 157mm
Maximum Fixture Thickness 3mm, 6mm, 8mm, 10mm, 12mm,
15mm, 20mm, 25mm, 30mm,
35mm, 45mm, 50mm, 55mm,
65mm, 70mm,
Indicative Working
Max Tensile 2.7kN -16.6kN
Loads in 32MPa Concrete* Max Shear 2.5kN - 15.6kN
Substrates
Concrete, Solid Brick, Solid Block,
Hollow Brick, Hollow Block, Hollow Slab
* Refer to load table
56
www.ramset.com.au
Related Products
DynaDrill
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
DynaBolt Plus
Sleeve Anchors
Racking Installer
Installation
1. Drill or core a hole to the recommended diameter and depth using the
fixture as a template. Clean the hole thoroughly with a hole cleaning
brush. Remove the debris with a hand pump, compressed air, or vacuum.
2. Insert the DynaBolt Plus through the fixture and drive with a hammer
until the washer contacts the fixture.
3. Tighten the DynaBolt Plus, allowing the sleeve to twist and pull down the
fixture firmly onto the substrate. For optimum performance, a torque
wrench should be used.
AU
ONLY
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
D6026
M4.5 3 26 6 8 30 23
100
DP06040
M4.5 12 38 6 8 45 34
100
DP06060
M4.5 30 57 6 8 55 53
100
DP08040 M6
6
40
8
10
50
34 100
DP08065 M6
25
66
8 10
65 60 50
DP08090 M6
50
92
8 10
75 86 50
DP10040
M8 3 41 10 12 50 34
50
DP10050
M8 20 49 10 12 55 42
50
DP10075
M8 30 76 10 12 65 69
50
DP10100 M8
50
103 10 12
80 96 25
DP10125 M8
80
124
10 12
85 117 25
DP12060
M10 10 55 12 15 70 47
25
DP12070
M10 15 70 12 15 70 62
25
DP12100
M10 45 98 12 15 95 90
20
DP12125 M10
70
126
12 15
95 118 20
DP16065
M12 6 62 16 19 80 51
20
DP16110
M12 35 106 16 19 120 95
10
DP16140
M12 65 140 16 19 120 129
10
DP20080 M16
8
81
20 24 100 70 10
DP20115
M16 25 113 20 24 125 102
5
DP20160
M16 70 157 20 24 155 146
5
www.ramset.co.nz
0800RAMSET (726739)
57
DynaBolt
Sleeve Anchors
ZINC
Electroplated
ZINC
Electroplated
5.8
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
DP10040GH
M8 3 41 10 12 50 34
50
AU
ONLY
DP10050GH
M8 20
DP10075GH
M8 30
DP10100GH M8
50
DP12060GH
M10 10
DP12070GH
M10 15
DP12100GH
M10 45
DP12125GH M10
70
DP16065GH
M12 6
DP16110GH
M12 35
DP16140GH
M12 65
DP20080GH M16
8
DP20115GH
M16 25
49 10 12 55 42
50
76 10 12 65 69
50
103
10
12
80
96 25
55 12 15 70 47
25
70 12 15 70 62
25
98 12 15 95 90
20
126
12
15
95
118 20
62 16 19 80 51
20
106 16 19 120 95
10
140 16 19 120 129
10
81
20
24
100
70 10
113 20 24 125 102
5
DynaBolt Plus Sleeve Anchor Hex Nut - Stainless Steel Grade AISI 316 (A4)
ZINC
Electroplated
ZINC
Electroplated
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
DP06040SS
M4.5 12 38 6 8 45 34
100
DP06060SS
M4.5 30 57 6 8 55 53
100
DP08040SS M6
6
40
8
10
50
34 100
DP08065SS M6
25
66
8
10
65
60 50
DP10050SS
M8 20 49 10 12 55 42
50
DP10075SS
M8 30 76 10 12 65 69
50
DP10100SS M8
50
103
10
12
80
96 25
DP12060SS
M10 10 55 12 15 70 47
25
DP12070SS
M10 15 70 12 15 70 62
25
DP12100SS
M10 45 98 12 15 95 90
20
AU
ONLY
DP12125SS M10
70
126
12
15
95
118 20
ZINC
Electroplated
5.8
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
AU
DP08045H M6
15
45
8
10
55
34 100
ONLY
DP08070H M6
32
70
8
10
65
60 50
DP10045H
M8 8 45 10 12 55 34
50
DP10055H
M8 20 55 10 12 55 42
50
DP10080H
M8 30 80 10 12 80 69
50
DP10105H M8
60
105
10
12
85
96 25
DP12065H
M10 15 65 12 15 75 47
25
DP12075H
M10 20 75 12 15 75 62
25
DP12105H M10
50
110
12
15
95
90 20
DP16110H M12
49
110
16
19
95
95 10
58
www.ramset.com.au
DynaBolt
Sleeve Anchors
DynaBolt Sleeve Anchor Hex Bolt- Stainless Steel Grade AISI 316 (A4)
ZINC
Electroplated
ZINC
Electroplated
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
DP08045HSS M6
15
45
8
10
55
34
100
AU
ONLY DP08070HSS M6
32
70
8
10
65
60 50
DP10045HSS
M8 8 45 10 12 55 34
50
DP10060HSS
M8 20 60 10 12 60 56
50
DP10080HSS
M8 30 80 10 12 80 69
50
DP10105HSS M8
60
105
10
12
85
96 25
DP12075HSS
M10 20 75 12 15 75 62
25
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
D6032R
M4.5 5 32 6 8 40 30
100
AU
ONLY DP06055R
M4.5 25 55 6 8 50 25
100
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
D6034F
M4.5 10 34 6 8 40 30
100
DP06060F
M4.5 30 60 6 8 50 25
100
DP06075F
M4.5 45 75 6 8 50 25
100
DP06100F M4.5
70
100
6
8
60
25 100
DP08060F M6
20
60
8
10
70
30 100
DP08085F M6
45
85
8
10
75
30 50
DP10075F
M8 30 75 10 12 85 34
50
DP10100F M8
55
100
10 12
85
34 50
M8 80 125 10 12 105 34
25
AU DP10125F
ONLY
DynaBolt Sleeve Anchor Countersunk Head- Stainless Steel Grade AISI 316 (A4)
ZINC
Electroplated
ZINC
Electroplated
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
Hole (mm)
Depth (mm)
Length (mm)
Qty
DP06060FSS
M4.5 30 60 6 8 50 25
100
AU
ONLY DP06075FSS
M4.5 45 75 6 8 50 25
100
www.ramset.co.nz
0800RAMSET (726739)
59
DynaBolt
Sleeve Anchors
5.8
ZINC
Electroplated
ZINC
Electroplated
Stainless
Steel 316
Galvanised
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
DO6026S M4.5
-
26
6
-
30
23 500
D06038S M4.5
-
38
6
-
41
34 100
5.8
ZINC
Electroplated
ZINC
Electroplated
Stainless
Steel 316
Galvanised
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
D08042E M6
-
42
8
-
50
34 100
AU
ONLY
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
D08045K M6
-
47
8
-
55
32 100
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
D08045X M6
-
47
8
-
55
32 100
Thread
Size
M4.5
M6
M8
M10
M12
M16
Embedment
Depth (mm)
25
35
45
50
65
85
Tightening
Torque (Nm)
10
15
35
55
85
165
Min Edge
Distance (mm)
55
60
70
75
100
130
Min Anchor
Spacing (mm)
75
105
135
150
195
255
Max Tensile
Load, Na (kN)*
2.7
4.2
5.9
7.7
11.9
16.6
*The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset Specifiers Resource Book for more information or explanation of technical data.
60
www.ramset.com.au
Max Shear
Load, Va (kN)*
2.5
4.0
6.4
7.9
10.5
15.6
DynaBolt
Sleeve Anchors
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
DynaBolt Decorative Post Head - Countersunk - ZincPlated & Stainless Steel 316
ZINC
Electroplated
ZINC
Electroplated
5.8
Galvanised
ZINC
Electroplated
Stainless
ZINC
Steel 316
Electroplated
Carbon Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
REM06 M6
-
44
-
-
-
- 100
AU
ONLY REM08 M8
-
47
-
-
-
- 100
REM10 M10
-
52
- -
-
- 50
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
DF045SS* M4.5
-
23
-
8
-
- 100
RFM06
M6 - 23 - 10 - -
100
AU
ONLY DF06SS*
M6 - 23 - 10 - -
100
RFM08
M8 - 27 - 12 - -
100
DF08SS*
M8 - 27 - 12 - -
100
*Denotes Stainless Steel Grade AISI 316 (A4)
DynaBolt Decorative Post Head - Round - ZincPlated & Stainless Steel 316
ZINC
Electroplated
ZINC
Electroplated
5.8
Galvanised
ZINC
Electroplated
Stainless
ZINC
Steel 316
Electroplated
Carbon Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Part No.
Thread
Max Fixture
Overall Anchor Drilled Hole Fixture Hole
Min Hole
Effective
Order
Size
Thickness (mm)
Length (mm)
(mm)
(mm)
Depth (mm)
Length (mm)
Qty
DR045SS* M4.5
-
22
-
8
-
- 100
AU
ONLY DR06 M6 - 22 -
10 - -
100
DR06SS*
M6 - 22 - 10 - -
100
*Denotes Stainless Steel Grade AISI 316 (A4)
www.ramset.co.nz
0800RAMSET (726739)
61
DynaSet
Drop-In Anchors
Internally threaded
anchor places
no restrictions on
fixture thickness
ZINC
Electroplated
Materials
ZINC
Galvanised
Electroplated
Stainless
Galvanised
Steel 316
5.8
5.8
Carbon
Stainless
Steel
Steel 316
Carbon Steel
Description
Specification
Material
Carbon Steel, Stainless Steel 316 (A4)
Corrosion Protection
Zinc Plating
Head Style
Fixing Method
Fixture Aligned
Setting Method
Displacement
Anchoring Method
Expansion
Thread Sizes
M6, M8, M10, M12, M16, M20
Drilled Hole Diameters
8mm, 10mm, 12mm, 15mm, 16mm, 20mm, 25mm
Anchor Lengths
25mm, 30mm, 40mm, 50mm, 60mm,
65mm, 80mm
Maximum Fixture Thickness Indicative Working
Max Tensile 2.5kN -15.8kN
Loads in 32MPa Concrete* Max Shear 2.2kN - 13.1kN
Substrates
Concrete
* Refer to load table
Related Products
DynaDrill
Carbide Drill Bits
Diamond Motor
Diamond Core Drill Bits
Hole Cleaning Brush
62
www.ramset.com.au
The Dyna Set fits flush with, or just below, the surface of the substrate,
leaving no protrusions when not in use and allowing for easy patch work.
The anchors internal thread facilitates the use of machine bolts and
threaded studs of any length, removing restrictions on fixture thickness.
The DynaSet requires only shallow embedment, which reduces the risk
of drilling into rebar.
The setting tool provides a visual expansion check for correct setting of the
anchor.
The flanged version (zinc plated only) has a retaining lip to keep the
anchor flush with the surface of the substrate. This also allows for
consistent threaded rod drop lengths.
DynaSet
Drop-In Anchors
Installation
1. Drill or core a hole to the recommended diameter and depth. Clean the
hole thoroughly with a hole cleaning brush. Remove the debris with a hand
pump, compressed air, or vacuum.
2. Insert the anchor into the hole. Using a hammer and the appropriate
setting tool, drive the expansion plug into the anchor until the shoulder of
the tool rests against the surface of the anchor.
3. Position the fixture, insert the bolt or threaded rod and tighten with a
spanner.
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Overall Anchor
Drilled Hole
Min Hole
Setting
Order
Length (mm)
(mm)
Depth (mm)
Tool
Qty
25
8
28 SETDS1 100
30
10
33 SETDS2 100
40
12 43 SETDS3 50
50
16 53 SETDS4 50
65
20 68 SETDS5 25
80
25 83 SETDS6 25
5.8
ZINC
Electroplated
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Overall Anchor
Drilled Hole
Min Hole
Setting
Order
Length (mm)
(mm)
Depth (mm)
Tool
Qty
25
8
28 SETDS1 100
30
12 33 SETDF3 100
30
12 33 SETDF3 500
50
16 53 SETDS4 50
50
16
53 SETDS4 200
* Rod Anchoring Pack (RAP) includes setting tool in a handy carry bucket
Part No
Thread
Thread
Size
Length (mm)
DSM06SS M6
11
DSM08SS M8
13
DSM10SS M10
16
DSM12SS M12
21
DSM16SS M16
28
ZINC
Electroplated
Overall Anchor
Length (mm)
25
30
40
50
60
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Drilled Hole
Min Hole
Setting
Order
(mm)
Depth (mm)
Tool
Qty
8
28
SETDS1 100
10
33
SETDS2 100
12
43
SETDS3 50
15
53 SETDS4*/SETDSA4 50
20
68
SETDS5 25
www.ramset.co.nz
0800RAMSET (726739)
63
DynaSet
Drop-In Anchors
*The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset Specifiers Resource Book for more information or explanation of technical data.
Description
M6 x 25 Setting Tool
M8 x 30 Setting Tool
M10 x 40 Setting Tool
M10 x 30 Setting Tool
M12 x 50 Setting Tool
M16 x 65 Setting Tool
M20 x 80 Setting Tool
Suits
DSM06/DSF06 / DSM06SS
DSM08 / DSM08SS
DSM10 / DSM10SS
DSF10
DSM12 / DSF12 / DSM12SS
DSM16 / DSM16SS
DSM20
Installation
1. Drill or core a 15mm hole to depth of 130mm 2.5mm. Clean the hole thorougly
with a hole cleaning brush. Remove the debris with a hand pump, compressed air, or
vacuum.
2. Check depth is correct, using the reverse e nd of the setting tool (SETSA4).
The depth indicator groove MUST be level with the concrete surface.
3. Insert the DSM12SS into the hole
4. Using a hammer and the setting tool, drive t he expansion plug into the anchor until
the depth indication groove is level with the c oncretesurface. If this cannot be
achieved, an alternative anchor point location must be selected.
5. Insert safety ring anchor and rubber seal. Tighten with a bar to the following
Tightening Specification:
b. Using a 150mm long bar, not more than 10mm in diameter and of yield
strength not exceeding 300MPa. R10 reinforcement bar is suitable for this
purpose. When the bar starts to bend, the anchor ring should be returned back to
the closest vertical orientation.
Ensure the anchor ring is left in a vertical position.
The DynaSet will remain in position if the safety ring anchor is removed.
64
www.ramset.com.au
Order Qty
1
1
1
1
1
1
1
Light Duty
Mechanical Anchoring
www.ramset.co.nz
0800RAMSET (726739)
65
RamPlug
Materials
5.8
Nylon
olid Concrete
ZINC
Electroplated
ZINC
Galvanised
Electroplated
Solid Brick
Stainless
ZINC
Electroplated
Steel 316
Carbon
Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Description
Material - Sleeve
Nylon
Material
Screw
Carbon Steel
AU
ONLY (Ultra Long only)
Corrosion Protection
Zinc Plating
(Ultra Long only)
Head Style
Countersunk, Hex
(Ultra Long only)
Fixing Method
Through Fixture (Long, Ultra Long)
Fixture Aligned (Standard)
Setting Method
Rotation
Anchoring Method
Interference Fit
Screw Gauge
5 - 24
Drilled Hole Diameters
5mm, 6mm, 7mm, 8mm, 10mm, 12mm
Anchor Lengths
25mm, 30mm, 40mm, 50mm, 60mm,
80mm, 100mm, 135mm, 160mm
Maximum
Fixture
Thickness 10mm,
45mm, 70mm
AU
ONLY (Ultra Long and Long only)
Substrates
Concrete, Stone, Solid Brick, Hollow Brick,
Solid Block, Hollow Block, Hollow Slab,
Lightweight Concrete (AAC) Block
www.ramset.com.au
Related Products
Specification
66
Impact Driver
Hex Sockets
Drill Driver
Screw Gun
Screwdriver Bits
RamPlug
Window/Door Installer
4
1. Drill a hole to the recommended diameter and depth using the fixture as
a template. If the fixture thickness is less than the maximum, increase the
hole depth accordingly. Clean the hole thoroughly with a hole cleaning
brush. Remove the debris with a hand pump, compressed air, or vacuum.
2. Insert the anchor through the fixture and tap with a hammer until the collar
of the anchor contacts the fixture.
3. Tighten screw until the head of the screw is flush with the collar of the
anchor.
AU
ONLY
Part No
DNP05
DNP06
DNP07
DNP08
DNP10
DNP12
Anchor
Size (mm)
5
6
7
8
10
12
Max Fixture
Thickness (mm)
-
-
-
-
-
-
Overall Anchor
Length (mm)
25
30
30
40
50
60
Drilled Hole
(mm)
5
6
7
8
10
12
Min Hole
Depth (mm)
30
40
40
50
60
75
Screw
Gauge
5 - 7
6 - 9
9 - 12
10 - 14
14 - 18
18 - 24
Order
Qty
100
100
100
100
50
25
Overall Anchor
Length (mm)
80
80
Drilled Hole
(mm)
8
10
Min Hole
Depth (mm)
90
90
Screw
Gauge
10 - 14
14 - 18
Order
Qty
100
50
Overall Anchor
Length (mm)
80
80
100
100
135
135
160
160
Drilled Hole
Min Hole
(mm)
Depth (mm)
10
90
10
90
10
110
10
110
10
145
10
145
10
170
10
170
AU
ONLY
Part No
DLP08
DLP10
Anchor
Size (mm)
8
10
Max Fixture
Thickness (mm)
10
10
Countersunk
www.ramset.co.nz
Head
Order
Style
Qty
Countersunk 25
Hex
25
Countersunk 25
Hex
25
Countersunk 25
Hex
25
Countersunk 25
Hex
25
0800RAMSET (726739)
67
EasyDrive
ZINC
ZINC
Electroplated
Electroplated
Materials
ZINC
Galvanised
Electroplated
Stainless
Galvanised
Steel 316
5.8
5.8
Carbon
Stainless
Steel
Steel 316
Carbon Steel
Description
Specification
Related Products
Material - Sleeve
Nylon
Material - Drive Screw
Carbon Steel, Stainless Steel 316 (A4)
Corrosion Protection
Zinc Plating
Head Style - Drive Screw Countersunk
Fixing Method
Through Fixture
Setting Method
Impact/Rotation
Anchoring Method
Interference Fit
Drilled Hole Diameters
5mm, 6mm, 8mm
Anchor Lengths
33mm, 42mm, 55mm
75mm, 120mm
Maximum Fixture Thickness 6mm,12mm, 25mm, 30mm, 40mm, 75mm
Substrates
Concrete, Stone, Solid Brick, Solid Block,
Hollow Block, Hollow Slab, Hollow Brick
68
www.ramset.com.au
Screw Gun
Screwdriver Bits
EasyDrive
Nylon Drive Anchors
Installation
1. Drill a hole to the recommended diameter and depth using the fixture as
a template. If the fixture thickness is less than the maximum, increase the
hole depth accordingly. Remove the debris with a hand pump, compressed
air, or vacuum.
2. Insert the anchor through the fixture until the collar of the anchor contacts
the fixture.
3. Screw or tap home the drive screw with a hammer until the head is flush
with the collar of the anchor. The drive screw can easily be removed with a
screwdriver.
5.8
ZINC
Electroplated
ZINC
Electroplated
Galvanised
Stainless
Steel 316
Carbon Steel
Part No
Anchor
Max Fixture
Overall Anchor
Drilled Hole
Min Hole
Order
Size (mm)
Thickness (mm)
Length (mm)
(mm)
Depth (mm)
Qty
ED05033 5
6 33 5 40 100
ED05050 5
20 50 5 45 100
AU
ONLY
ED06042 6
12 42 6 50 100
ED06055 6
25 55 6 50 100
ED06075 6
40 70 6 50 100
ED08080 8
30 75 8 80 50
AU
ONLY ED08120 8
75 120 8 95 50
EasyDrive Nylon Anchors - Stainless Steel AISI 316 (A4) Drive Screw
ZINC
Electroplated
ZINC
Electroplated
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Part No
Anchor
Max Fixture
Overall Anchor
Drilled Hole
Min Hole
Size (mm)
Thickness (mm)
Length (mm)
(mm)
Depth (mm)
ED05033SS 5
6
33 5 40
ED06042SS 6
12
42 6 50
ED06055SS 6
25
55 6 50
ED06075SS 6
40
70 6 50
www.ramset.co.nz
0800RAMSET (726739)
Order
Qty
100
100
100
100
69
Nylon Anchors
olid Concrete
ZINC
Electroplated
Materials
Nylon
ZINC
ZINC
Electroplated
Electroplated
Solid Brick
ZINC
Galvanised
Electroplated
Stainless
Galvanised
Steel 316
5.8
5.8
Carbon
Stainless
Steel
Steel 316
Carbon Steel
Description
Specification
Related Products
Material - Sleeve
Nylon
Material - Drive Screw
Carbon Steel, Stainless Steel 316 (A4)
Corrosion Protection
Zinc Plating
Head Style - Anchor
Mushroom, Round, Countersunk, Flat
Fixing Method
Through Fixture
Setting Method
Impact/Rotation
Anchoring Method
Interference Fit
Drilled Hole Diameters
5mm, 6.5mm
Anchor Lengths
25mm, 38mm, 50mm, 75mm
Maximum Fixture Thickness 2mm, 5mm,13mm, 25mm, 50mm
Substrates
Concrete, Stone, Solid Brick, Solid Block
70
www.ramset.com.au
Drill Driver
Screw Gun
Screwdriver Bits
Nylon Anchors
Trades & Applications
Electrical Contractor
Signwriter
Plumbing Contractor
Electrical Fitting Installation
4
Sign Installation
4
Pipe/Conduit Saddle Installation
4
4
Installation
1. Drill a hole to the recommended diameter and depth using the fixture as
a template. If the fixture thickness is less than the maximum, increase the
hole depth accordingly. Remove the debris with a hand pump, compressed
air, or vacuum.
2. Insert the anchor through the fixture until the collar of the anchor contacts
the fixture.
3. Screw or hammer home the drive screw until the head is flush with the
collar of the anchor. The drive screw can easily be removed with a
screwdriver.
# Available with stainless steel expansion nail. Add SS to end of Part No.
AU
ONLY
# Available with stainless steel expansion nail. Add SS to end of Part No.
AU
ONLY
www.ramset.co.nz
0800RAMSET (726739)
71
ShureDrive
Drive Anchors
ZINC
Galvanised
Electroplated
Materials
5.8
Stainless
ZINC
Electroplated
Steel 316
Carbon
Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Description
The ShureDrive Drive Anchor is an all metal light duty, impact setting,
interference fit anchor, designed for tamper resistant use in a variety of
substrates such as concrete, stone, solid brick, solid block, hollow brick,
hollow block and hollow slab.
Material
Zinc Alloy Body, Carbon Steel Nail
Corrosion Protection
Zinc Plating
Head Style - Anchor
Mushroom
Fixing Method
Through Fixture
Setting Method
Impact
Anchoring Method
Interference Fit
Drilled Hole Diameters
5mm, 6mm
Anchor Lengths
22mm, 30mm, 50mm
Maximum Fixture Thickness 3mm, 5mm, 25mm
Substrates
Concrete, Stone, Solid Brick, Solid Block,
Grout Filled Block, Hollow Brick, Hollow Block,
Hollow Slab
www.ramset.com.au
Specification
72
Related Products
ShureDrive
Drive Anchors
Signwriter
Plumbing Contractor
Brick Tie Installation
Sign Installation
4
Pipe/Conduit Saddle Installation
4
4
Bricklayer
4
Installation
1. Drill a hole to the recommended diameter and depth using the fixture as a
template. Remove the debris with a hand pump, compressed air, or
vacuum.
2. Insert the anchor through the fixture until the flange of the anchor contacts
the fixture.
3. Hammer home the expansion nail until the head is flush with the flange of
the anchor.
ShureDrive Anchors
Part No
Anchor
Max Fixture
Overall Anchor
Head
Drilled
Fixture Hole
Min Hole
Order
Size
Thickness
Length
Hole
Depth
Qty
(mm) (mm) (mm) (mm) (mm) (mm)
(mm)
SDM05022
5
3
22
11
5
6 30 100
SDM06030
6
5
30
13
6
7 35 100
SDM06030SS 6
5
30
13
6
7 35 100
SDM06050
6
25
50
13
6
7 55 100
www.ramset.co.nz
0800RAMSET (726739)
73
Concrete Nails
Pre-assembled washer
improves pullover strength
(CW - Washered range only)
ZINC
Galvanised
Electroplated
Materials
5.8
Stainless
ZINC
Electroplated
Steel 316
Carbon
Steel
Galvanised
5.8
Stainless
Steel 316
Carbon Steel
Description
Specification
Material
Carbon Steel
Corrosion Protection
Zinc Plating, Mechanical Galvanising
Head Style
Flat, Countersunk, Bullet
Fixing Method
Through fixture
Setting Method
Impact
Anchoring Method
Interference fit
Shank Diameters
2.4mm, 3.2mm, 3.8mm
Anchor Length
25mm, 30mm, 40mm, 50mm,
60mm, 75mm
Maximum Fixture Thickness up to 50mm
Substrates
Concrete, Solid Block
74
www.ramset.com.au
Concrete Nails
Trades & Applications
Carpenter
Signwriter
Plumbing
Contractor
Electrical
Contractor
Concrete
Formworker
Installation
1. Hammer the concrete nail through the fixture into the concrete until the
nail head is flush with the fixture.
CF - Plain Shank
CW - Washered
Concrete Nails
Part No
CD425
AU
ONLY
CD430
CD440
CD525
CD540
CF650
CF660
CF675
CW415
CW415Q500
CW420
CW420Q500
CW425
CW425Q500
CW430
CW430Q500
CW440
CK540
CK750
CK760
CK775
Description
Plain
Plain
Plain
Plain
Plain
Plain
Plain
Plain
Washered
Washered
Washered
Washered
Washered
Washered
Washered
Washered
Washered
Striated
Striated
Striated
Striated
Shank (mm)
2.4
2.4
2.4
3.2
3.2
3.8
3.8
3.8
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
3.2
3.6
4.0
4.2
www.ramset.co.nz
0800RAMSET (726739)
Order Qty
100
100
100
100
100
100
100
100
100
500
100
500
100
500
100
500
100
100
100
100
100
75
Notes
76
www.ramset.com.au
Specialised
Mechanical Anchoring
www.ramset.co.nz
0800RAMSET (726739)
77
Trubolt
ETA Approved
for Cracked
Concrete
Ramset TruBolt Advantages:
A self expanding stud anchor. Torque controlled mechanical
through fixing, for speed and afficiency on site. Conforms to
ETA option 1, approved for an assured fix into cracked and
non-cracked concrete.
ETA Option 1 approved anchor For cracked and noncracked concrete
Highest Performance in Cracked Concrete for floor, wall
and overhead applications
TR020 Fire tested Fire Rated Performance up to 120
minutes
FM Approved
Transport for London Underground authorised for use
Nut of Class 8 European Standard
Approvals
Certification
European Technical Approval ETAG 001-5 Option 1
FM Approved
Transport for London Underground authorised for use
78
www.ramset.com.au
ETA
European Technical Assessment
Option 1
Substrates
Concrete
Solid Stone
Applications
Technical Specification
Thread
Diameter
Drill
Diameter
Total
anchor
length
Hole depth
minus fixture
thickness
Minimum
Drilling
depth
Maximum
fixture
thickness
Maximum
tightening
Torque
Fixture
clearance
hole
diameter
T06055SSA
Trubolt M6 x 55mm
55mm
66mm
51mm
15mm
10Nn
T08055SSA
Trubolt M8 x 55mm
55mm
70mm
65mm
5mm
20Nn
T08070SSA
Trubolt M8 x 70mm
70mm
85mm
65mm
20mm
20Nn
T08090SSA
Trubolt M8 x 90mm
90mm
105mm
65mm
40mm
20Nn
T08130SSA
Trubolt M8 x 130mm
130mm
145mm
65mm
80mm
20Nn
T10065SSA
10
10
65mm
83mm
78mm
5mm
35Nn
12
T10075SSA
10
10
75mm
93mm
78mm
15mm
35Nn
12
T10095SSA
10
10
95mm
113mm
78mm
35mm
35Nn
12
T10120SSA
10
10
120mm
138mm
78mm
60mm
35Nn
12
T12080SSA
12
12
80mm
100mm
95mm
5mm
50Nn
14
T12100SSA
12
12
100mm
120mm
95mm
25mm
50Nn
14
T12115SSA
12
12
115mm
135mm
95mm
40mm
50Nn
14
T12140SSA
12
12
140mm
160mm
95mm
65mm
50Nn
14
T16125SSA
16
16
125mm
147mm
117mm
30mm
100Nn
18
T16150SSA
16
16
150mm
172mm
117mm
55mm
100Nn
18
T16170SSA
16
16
170mm
192mm
117mm
75mm
100Nn
18
Ramset
Part No
Installation
1. Drill or core a hole to the recommended diameter (same as the TruBolt) and depth using the
fixture as a template.
Clean the hole thoroughly with a hole cleaning brush. Remove the debris with a hand pump,
compressed air, or vacuum.
2. Insert the anchor through the fixture and drive with a hammer until the washer contacts the fixture.
3. Tighten the nut with a torque wrench to the specified assembly torque.
www.ramset.co.nz
0800RAMSET (726739)
79
Insulation Anchor
For Cracked Concrete
NZ
ONLY
Description
Drill
Diameter
Overall
Length
Max Insulation
Thickness
Min Drill
Depth
Minimum
Embedment
Box
Quantity
S057600
10 - 30
10mm
60mm
30mm
50mm
30mm
200
S057610
40 - 60
10mm
90mm
60mm
50mm
30mm
200
S057620
70 - 80
10mm
110mm
80mm
50mm
30mm
200
S057630*
90 - 100
10mm
130mm
100mm
50mm
30mm
200
S057640*
110 - 120
10mm
150mm
120mm
50mm
30mm
200
Product Range - ISO Universal Insulation Anchor Indicative Loads - Wall Insulation Substrates
Anchor (mm)
10 - 30
0.15kN
0.07kN
0.15kN
40 - 60+
0.20kN
0.13kN
0.20kN
Product Range - ISO Universal Insulation Anchor Indicative - Soffit Insulation Substrates
Anchor (mm)
10 - 30
0.07kN
0.04kN
0.07kN
40 - 60+
0.10kN
0.06kN
0.10kN
80
www.ramset.com.au
Approvals
Insulation Anchor
Ma
Exp
(Ex
Substrates
NZ
ONLY
Applications
Hollow floor beams
Concrete
Anc
Solid block
The
Solid brick
Tem
materials
Stone
Installation
Installation
1. D
Product Advantages
2. In
3. In
n
A.
B.
Specification
The expansion portion of the anchor is set by hammering in an
integral expansion nail.
Material
Expansion nail: Glass reinforced polamide 6
(Except part 057600 - Polypropylene).
Anchor Body:
Thermal conductivity:
Temperature Range in use:
Polypropylene
0.12 W/m - C
-30C to +80C
168
www.ramset.co.nz
0800RAMSET (726739)
81
InsulFast
Drill Anchor
AU
ONLY
Specialised Anchors
Gripping barbs
Description
The InsulFast Drill Anchor is a light duty, impact set, interference fit anchor,
designed for fixing the majority of insulation materials to solid substrates
such as concrete, brick, block and stone.
Specification
Material
Polypropylene
Temperature Range
-30C to + 80C
Head Style
Disc
Fixing Method
Through Fixture
Setting Method
Impact
Anchoring Method
Interference Fit
Drilled Hole Diameter
8mm
Anchor Lengths
95mm, 115mm, 135mm
Min/Max Insulation
50/60mm, 70/80mm,
Thickness- 90/100mm
Indicative Tensile Loads
Concrete - 10kg
Solid Brick - 8kg
Stone/Solid Block - 6kg
Substrates
Stone, Concrete, Solid Brick, Solid Block
82
www.ramset.com.au
Related Products
InsulFast
Drill Anchor
Insulation Contractor
Fibreglass / Rockwool
(Compatibility dependent on ability
to drill through insulation)
Expanded Polystyrene
Installation
1. Drill an 8mm hole through the insulation and a further 45mm into the
substrate.
2. Insert the anchor through the insulation and into the pre-drilled hole.
3. Using light hammer blows, drive the anchor into the hole until the head of
the anchor is in contact with the insulation and the insulation is firmly held
against the substrate.
Specialised Anchors
Extruded Polystyrene
www.ramset.co.nz
0800RAMSET (726739)
83
Anchor Description
Tapconwater
Screw Anchor
Drinking
safe
SAMMYS Screw
Anchor for Threaded
Rod
Image
Overhead Suspension
Overhead Suspension
EPCONC8 used to
install post-installed
rebar
Rebar connections
for wall, slab,
columns and beams
Starter Bars
SpaTec Plus
Structural Steel/
Columns/Beams
Cracked concrete
ICC-ESR3614
CSTB-3/12-727
Test as per ACI 355.4
ETA-10/0276
Anchor Type
8mm x 55mm
6.5mm
3511407
8mm x 75mm
6.5mm
3507407
9.5mm x 75mm
9.5mm
LDT3830
9.5mm x 100mm
9.5mm
LDT3840
13mm x 150mm
13mm
LDT1260
M10 x 45mm
6.5mm
8173957
15mm x 105mm
15mm
SP10105
84
Seismic
Qualification
Application
www.ramset.com.au
www.ramset.co.nz
0800RAMSET (726739)
85
Hollow Wall
Anchors
Anti-rotation barbs
Integral nut
Collapsing legs
Description
The Ramset Hollow Wall Anchor is an all metal, light duty, cavity fixing for
plasterboard and other hollow wall materials up to 38mm.
The Hollow Wall Anchors low profile head allows for flush finishing.
The anchors large flange prevents the head from pulling into the
substrate.
Anti-rotation barbs, incorporated in the flange, prevent the anchor from
spinning in the hole.
Collapsing legs with an integral nut provide high strength and allow the
screw to be removed without loosing the anchor inside the cavity.
Specification
Material
Pressed Steel Body, Carbon Steel Screw
Corrosion Protection
Zinc Plating
Head Style
Slotted Philips Button Head
Fixing Method
Fixture Aligned
Setting Method
Setting Tool/Rotation
Anchoring Method
Deformation
Thread Diameters
M4, M5, M6
Drilled Hole Diameters
8mm, 9mm, 13mm
Wall Thickness
0mm-5mm, 6mm-10mm, 6mm-16mm,
8mm-13mm, 16mm-24mm, 34mm-38mm
Maximum Fixture Thickness 10mm, 15mm, 17mm, 20mm, 22mm
Substrates
Plasterboard, Ply Wood, Cement Sheet
86
www.ramset.com.au
Related Products
Drill
Drill Bits
Drill Driver
Screw Gun
Screwdriver Bits
Hollow Wall Anchor Setting Tool
Hollow Wall
Anchors
4
4
Miscellaneous Trades
Plumbing Contractor
Light Hook/Bracket Installation
4
Electrical Fitting Installation
Pipe/Conduit Saddle Installation
4
Installation
1. Drill a hole to the recommended diameter.
(HW10M4P may be hammered into plasterboard)
2. Tap the anchor into the hole until it is flush with the surface of
the substrate.
3. Attach the setting tool to the head of the screw.
Squeeze the trigger to expand the anchor.
(Small sizes may be set using a screwdriver)
4. Remove the screw and place it through the fixture then back into the
anchor. Tighten the screw until the fixture is fixed.
Thread
Size
M4
M4
M4
M4
M4
M5
M6
Wall
Thickness (mm)
0 - 5
6 - 10
8 - 13
16 - 24
34 - 38
8 - 13
6 - 16
Max Fixture
Thickness (mm)
10
15
15
17
15
20
22
Drilled Hole
(mm)
8
8
8
8
8
9
13
Order
Qty
100
100
100
100
100
100
100
Description
Setting Tool
Order Qty
1
www.ramset.co.nz
0800RAMSET (726739)
87
WallMate
Plasterboard Anchors
Flush head
Description
Specification
Material
Nylon, Zinc Composite
Corrosion Protection
Head Style
Flush - Phillips #2
Fixing Method
Fixture Aligned
Setting Method
Rotation
Anchoring Method
Thread Forming
Screw Gauges
6-8
Drilled Hole Diameters*
8mm
Anchor Lengths
42mm
Minimum Screw Length 20mm
Substrates
Plasterboard, Dry Partition Walls, Aerated
Concrete (with 8mm pre-drilled hole)
*For pre-drilling into aerated concrete
88
www.ramset.com.au
Both versions of the WallMate feature an effective drill point for easy
penetration of plasterboard and fast installation. If a long screw is used,
this point will break away so as not to restrict achievement of a firm fix.
The anchors screw thread profile is designed for efficient cutting and
positive grip.
Both the screw and the WallMate can be easily removed without losing
the anchor inside the cavity.
The low profile head allows for flush fixing.
Related Products
Drill
Hole Cleaning Pump*
Wet and Dry Vacuum*
Drill Driver
Screw Gun
Drill Bits
WallMate
Plasterboard Anchors
Trades & Applications
Electrical Contractor
Miscellaneous Trades
Plumbing Contractor
Light Hook/Bracket Installation
4
Electrical Fitting Installation
Bathroom Accessory Installation
4
Installation
1. Insert the point of a #2 Philips Head screwdriver into the recess of the
WallMate, place the drill point against the wall, lightly piercing the face
paper, and screw the anchor into the plasterboard until the head is flush
with the surface.
2. Place the fixture over the anchor, insert the appropriate gauge screw
through the fixture, into the head of the WallMate and tighten the fixture
in place.
NYLON
METAL
WMZ
AU
ONLY
WM25
Anchor
Length (mm)
42
42
Min Screw
Length (mm)
20
20
Drilled Hole
* (mm)
8
8
Screw
Gauge
6-8
6-8
Body
Type
Metal
Nylon
Order
Qty
100
250
42
42
20
20
8
8
6-8
6-8
Metal
Nylon
100
100
www.ramset.co.nz
0800RAMSET (726739)
89
Notes
Notes
90
www.ramset.com.au
AUSTRALIA
Sales, Orders and Enquiries
Fax:
Tel:
Email:
Web:
NEW ZEALAND
Sales, Orders and Enquiries
Fax:
Tel:
Email:
Web:
enquiry@ramset.com.au
www.ramset.com.au
VICTORIA
5/71 Victoria Crescent, Abbotsford 3067
1 Ramset Drive, Chirnside Park 3116
SOUTH AUSTRALIA
115 Sir Donald Bradman Drive, Hilton 5033
ACT
5/19 Tennant Street, Fyshwick 2609
QUEENSLAND
53 Doggett Street, Newstead 4006
WESTERN AUSTRALIA
525 Abernethy Road, Kewdale 6105
Hamilton
15 Somerset St
p 07 847 9047
f 07 847 9980
e hamilton@ramset.co.nz
Napier - Onekawa
124 Taradale Road
p 06 843 0067
f 06 843 0043
e napier@ramset.co.nz
Christchurch - Hornby
Unit 2/37 Foremans Rd
p 03 349 4749
f 03 349 4750
e hornby@ramset.co.nz
Auckland - Penrose
35 Station Rd
p 09 579 3072
f 09 579 1701
e auckland@ramset.co.nz
Tauranga - Mt Maunganui
Unit 1, 15 Portside Drive
p 07 572 0520
f 07 572 0530
e tauranga@ramset.co.nz
Lower Hutt
46 Victoria St
p 04 569 7247
f 04 566 8752
e lowerhutt@ramset.co.nz
Dunedin
5 Melbourne St
p 03 455 1134
f 03 456 1388
e dunedin@ramset.co.nz
Auckland - Henderson
123 Central Park Drive
p 09 838 9865
f 09 837 3014
e henderson@ramset.co.nz
Rotorua
Waterford Park Estate
50 Old Taupo Rd
p 07 348 0190
f 07 348 9200
e rotorua@ramset.co.nz
Wellington
147 Taranaki St
p 04 384 4138
f 04 385 0868
e wellington@ramset.co.nz
Invercargill
121 Clyde St
p 03 218 9241
f 03 214 7787
e invercargill@ramset.co.nz
New Plymouth
p 06 759 8984
f 06 759 8983
e newplymouth@ramset.co.nz
Nelson
p 03 548 2664
f 03 548 3559
e nelson@ramset.co.nz
Queenstown
200A Glenda Dr
p 03 442 8073
f 03 442 8074
e queenstown@ramset.co.nz
Whangarei
2A Herekino St
p 09 438 2010
f 09 438 9188
e whangarei@ramset.co.nz
Palmerston North
903 Tremaine Avenue
p 06 357 6745
f 06 357 6775
e palmerstonnorth@ramset.co.nz
Christchurch - City
120 Montreal St
p 03 341 8710
f 03 341 8730
e christchurch@ramset.co.nz
In the interests of product improvement, Ramset reserves the right to alter product specifications as required. Information included in this resource book is correct at time of printing.
It is the responsibility of the user to ensure product selected is appropriate for its intended use. For further technical information go to www.ramset.com.au or contact Ramset on the numbers
indicated. ITW Australia Pty. Ltd. ABN 63 004 235 063 trading as Ramset Copyright 2015 Trademarks of Cetram Pty. Ltd. used under license by Ramset
PART No.RAMCMA2015ANZ
STATE BRANCHES